Convert atari_scsi to platform device and eliminate scsi_register(). Validate __setup options later on so that module options are checked as well. Remove the comment about the scsi mid-layer disabling the host irq as it is no longer true (AFAICT). Also remove the obsolete slow interrupt stuff (IRQ_TYPE_SLOW == 0 anyway). Signed-off-by: Finn Thain --- arch/m68k/atari/config.c | 5 drivers/scsi/atari_scsi.c | 426 ++++++++++++++++++++++------------------------ drivers/scsi/atari_scsi.h | 17 - 3 files changed, 217 insertions(+), 231 deletions(-) Index: linux/arch/m68k/atari/config.c =================================================================== --- linux.orig/arch/m68k/atari/config.c 2014-10-02 16:55:28.000000000 +1000 +++ linux/arch/m68k/atari/config.c 2014-10-02 16:56:21.000000000 +1000 @@ -892,6 +892,11 @@ int __init atari_platform_init(void) } #endif +#ifdef CONFIG_ATARI_SCSI + if (ATARIHW_PRESENT(ST_SCSI) || ATARIHW_PRESENT(TT_SCSI)) + platform_device_register_simple("atari_scsi", -1, NULL, 0); +#endif + return rv; } Index: linux/drivers/scsi/atari_scsi.c =================================================================== --- linux.orig/drivers/scsi/atari_scsi.c 2014-10-02 16:56:20.000000000 +1000 +++ linux/drivers/scsi/atari_scsi.c 2014-10-02 16:56:21.000000000 +1000 @@ -74,33 +74,26 @@ #define MAX_TAGS 32 #include -#include -#include #include -#include #include #include #include #include #include #include +#include #include #include #include -#include -#include -#include -#include - -#include -#include "atari_scsi.h" -#include "NCR5380.h" #include #include #include -#include +#include + +#include "atari_scsi.h" +#include "NCR5380.h" #define IS_A_TT() ATARIHW_PRESENT(TT_SCSI) @@ -176,25 +169,9 @@ static inline void DISABLE_IRQ(void) #define AFTER_RESET_DELAY (5*HZ/2) #endif -/***************************** Prototypes *****************************/ - #ifdef REAL_DMA static void atari_scsi_fetch_restbytes(void); #endif -static irqreturn_t scsi_tt_intr(int irq, void *dummy); -static irqreturn_t scsi_falcon_intr(int irq, void *dummy); -static void falcon_release_lock_if_possible(struct NCR5380_hostdata *hostdata); -static int falcon_get_lock(void); -#ifdef CONFIG_ATARI_SCSI_RESET_BOOT -static void atari_scsi_reset_boot(void); -#endif -static unsigned char atari_scsi_tt_reg_read(unsigned char reg); -static void atari_scsi_tt_reg_write(unsigned char reg, unsigned char value); -static unsigned char atari_scsi_falcon_reg_read(unsigned char reg); -static void atari_scsi_falcon_reg_write(unsigned char reg, unsigned char value); - -/************************* End of Prototypes **************************/ - static struct Scsi_Host *atari_scsi_host; static unsigned char (*atari_scsi_reg_read)(unsigned char reg); @@ -518,160 +495,12 @@ static int falcon_get_lock(void) } } - -static int __init atari_scsi_detect(struct scsi_host_template *host) -{ - static int called = 0; - struct Scsi_Host *instance; - - if (!MACH_IS_ATARI || - (!ATARIHW_PRESENT(ST_SCSI) && !ATARIHW_PRESENT(TT_SCSI)) || - called) - return 0; - - host->proc_name = "Atari"; - - atari_scsi_reg_read = IS_A_TT() ? atari_scsi_tt_reg_read : - atari_scsi_falcon_reg_read; - atari_scsi_reg_write = IS_A_TT() ? atari_scsi_tt_reg_write : - atari_scsi_falcon_reg_write; - - /* setup variables */ - host->can_queue = - (setup_can_queue > 0) ? setup_can_queue : - IS_A_TT() ? ATARI_TT_CAN_QUEUE : ATARI_FALCON_CAN_QUEUE; - host->cmd_per_lun = - (setup_cmd_per_lun > 0) ? setup_cmd_per_lun : - IS_A_TT() ? ATARI_TT_CMD_PER_LUN : ATARI_FALCON_CMD_PER_LUN; - /* Force sg_tablesize to 0 on a Falcon! */ - host->sg_tablesize = - !IS_A_TT() ? ATARI_FALCON_SG_TABLESIZE : - (setup_sg_tablesize >= 0) ? setup_sg_tablesize : ATARI_TT_SG_TABLESIZE; - - if (setup_hostid >= 0) - host->this_id = setup_hostid; - else { - /* use 7 as default */ - host->this_id = 7; - /* Test if a host id is set in the NVRam */ - if (ATARIHW_PRESENT(TT_CLK) && nvram_check_checksum()) { - unsigned char b = nvram_read_byte( 14 ); - /* Arbitration enabled? (for TOS) If yes, use configured host ID */ - if (b & 0x80) - host->this_id = b & 7; - } - } - -#ifdef SUPPORT_TAGS - if (setup_use_tagged_queuing < 0) - setup_use_tagged_queuing = 0; -#endif -#ifdef REAL_DMA - /* If running on a Falcon and if there's TT-Ram (i.e., more than one - * memory block, since there's always ST-Ram in a Falcon), then allocate a - * STRAM_BUFFER_SIZE byte dribble buffer for transfers from/to alternative - * Ram. - */ - if (MACH_IS_ATARI && ATARIHW_PRESENT(ST_SCSI) && - !ATARIHW_PRESENT(EXTD_DMA) && m68k_num_memory > 1) { - atari_dma_buffer = atari_stram_alloc(STRAM_BUFFER_SIZE, "SCSI"); - if (!atari_dma_buffer) { - printk(KERN_ERR "atari_scsi_detect: can't allocate ST-RAM " - "double buffer\n"); - return 0; - } - atari_dma_phys_buffer = atari_stram_to_phys(atari_dma_buffer); - atari_dma_orig_addr = 0; - } -#endif - instance = scsi_register(host, sizeof(struct NCR5380_hostdata)); - if (instance == NULL) { - atari_stram_free(atari_dma_buffer); - atari_dma_buffer = 0; - return 0; - } - atari_scsi_host = instance; - /* - * Set irq to 0, to avoid that the mid-level code disables our interrupt - * during queue_command calls. This is completely unnecessary, and even - * worse causes bad problems on the Falcon, where the int is shared with - * IDE and floppy! - */ - instance->irq = 0; - -#ifdef CONFIG_ATARI_SCSI_RESET_BOOT - atari_scsi_reset_boot(); -#endif - NCR5380_init(instance, 0); - - if (IS_A_TT()) { - - /* This int is actually "pseudo-slow", i.e. it acts like a slow - * interrupt after having cleared the pending flag for the DMA - * interrupt. */ - if (request_irq(IRQ_TT_MFP_SCSI, scsi_tt_intr, IRQ_TYPE_SLOW, - "SCSI NCR5380", instance)) { - printk(KERN_ERR "atari_scsi_detect: cannot allocate irq %d, aborting",IRQ_TT_MFP_SCSI); - scsi_unregister(atari_scsi_host); - atari_stram_free(atari_dma_buffer); - atari_dma_buffer = 0; - return 0; - } - tt_mfp.active_edge |= 0x80; /* SCSI int on L->H */ -#ifdef REAL_DMA - tt_scsi_dma.dma_ctrl = 0; - atari_dma_residual = 0; - - if (MACH_IS_MEDUSA) { - /* While the read overruns (described by Drew Eckhardt in - * NCR5380.c) never happened on TTs, they do in fact on the Medusa - * (This was the cause why SCSI didn't work right for so long - * there.) Since handling the overruns slows down a bit, I turned - * the #ifdef's into a runtime condition. - * - * In principle it should be sufficient to do max. 1 byte with - * PIO, but there is another problem on the Medusa with the DMA - * rest data register. So 'atari_read_overruns' is currently set - * to 4 to avoid having transfers that aren't a multiple of 4. If - * the rest data bug is fixed, this can be lowered to 1. - */ - atari_read_overruns = 4; - } -#endif /*REAL_DMA*/ - } else { /* ! IS_A_TT */ - - /* Nothing to do for the interrupt: the ST-DMA is initialized - * already by atari_init_INTS() - */ - -#ifdef REAL_DMA - atari_dma_residual = 0; - atari_dma_active = 0; - atari_dma_stram_mask = (ATARIHW_PRESENT(EXTD_DMA) ? 0x00000000 - : 0xff000000); -#endif - } - - called = 1; - return 1; -} - -static int atari_scsi_release(struct Scsi_Host *sh) -{ - if (IS_A_TT()) - free_irq(IRQ_TT_MFP_SCSI, sh); - if (atari_dma_buffer) - atari_stram_free(atari_dma_buffer); - NCR5380_exit(sh); - return 1; -} - #ifndef MODULE static int __init atari_scsi_setup(char *str) { /* Format of atascsi parameter is: * atascsi=,,,, - * Defaults depend on TT or Falcon, hostid determined at run time. + * Defaults depend on TT or Falcon, determined at run time. * Negative values mean don't change. */ int ints[6]; @@ -682,36 +511,17 @@ static int __init atari_scsi_setup(char printk("atari_scsi_setup: no arguments!\n"); return 0; } - - if (ints[0] >= 1) { - if (ints[1] > 0) - /* no limits on this, just > 0 */ - setup_can_queue = ints[1]; - } - if (ints[0] >= 2) { - if (ints[2] > 0) - setup_cmd_per_lun = ints[2]; - } - if (ints[0] >= 3) { - if (ints[3] >= 0) { - setup_sg_tablesize = ints[3]; - /* Must be <= SG_ALL (255) */ - if (setup_sg_tablesize > SG_ALL) - setup_sg_tablesize = SG_ALL; - } - } - if (ints[0] >= 4) { - /* Must be between 0 and 7 */ - if (ints[4] >= 0 && ints[4] <= 7) - setup_hostid = ints[4]; - else if (ints[4] > 7) - printk("atari_scsi_setup: invalid host ID %d !\n", ints[4]); - } + if (ints[0] >= 1) + setup_can_queue = ints[1]; + if (ints[0] >= 2) + setup_cmd_per_lun = ints[2]; + if (ints[0] >= 3) + setup_sg_tablesize = ints[3]; + if (ints[0] >= 4) + setup_hostid = ints[4]; #ifdef SUPPORT_TAGS - if (ints[0] >= 5) { - if (ints[5] >= 0) - setup_use_tagged_queuing = !!ints[5]; - } + if (ints[0] >= 5) + setup_use_tagged_queuing = ints[5]; #endif return 1; @@ -1020,23 +830,211 @@ static int atari_scsi_bus_reset(struct s return rv; } -static struct scsi_host_template driver_template = { +#define DRV_MODULE_NAME "atari_scsi" +#define PFX DRV_MODULE_NAME ": " + +static struct scsi_host_template atari_scsi_template = { + .module = THIS_MODULE, + .proc_name = DRV_MODULE_NAME, .show_info = atari_scsi_show_info, .name = "Atari native SCSI", - .detect = atari_scsi_detect, - .release = atari_scsi_release, .info = atari_scsi_info, .queuecommand = atari_scsi_queue_command, .eh_abort_handler = atari_scsi_abort, .eh_bus_reset_handler = atari_scsi_bus_reset, - .can_queue = 0, /* initialized at run-time */ - .this_id = 0, /* initialized at run-time */ - .sg_tablesize = 0, /* initialized at run-time */ - .cmd_per_lun = 0, /* initialized at run-time */ + .this_id = 7, .use_clustering = DISABLE_CLUSTERING }; +static int __init atari_scsi_probe(struct platform_device *pdev) +{ + struct Scsi_Host *instance; + int error; + + if (!MACH_IS_ATARI) + return -ENODEV; + + if (ATARIHW_PRESENT(TT_SCSI)) { + atari_scsi_reg_read = atari_scsi_tt_reg_read; + atari_scsi_reg_write = atari_scsi_tt_reg_write; + } else if (ATARIHW_PRESENT(ST_SCSI)) { + atari_scsi_reg_read = atari_scsi_falcon_reg_read; + atari_scsi_reg_write = atari_scsi_falcon_reg_write; + } else + return -ENODEV; + + /* The values for CMD_PER_LUN and CAN_QUEUE are somehow arbitrary. + * Higher values should work, too; try it! + * (But cmd_per_lun costs memory!) + * + * But there seems to be a bug somewhere that requires CAN_QUEUE to be + * 2*CMD_PER_LUN. At least on a TT, no spurious timeouts seen since + * changed CMD_PER_LUN... + * + * Note: The Falcon currently uses 8/1 setting due to unsolved problems + * with cmd_per_lun != 1 + */ + if (IS_A_TT()) { + atari_scsi_template.can_queue = 16; + atari_scsi_template.cmd_per_lun = 8; + atari_scsi_template.sg_tablesize = SG_ALL; + } else { + atari_scsi_template.can_queue = 8; + atari_scsi_template.cmd_per_lun = 1; + atari_scsi_template.sg_tablesize = SG_NONE; + } + + if (setup_can_queue > 0) + atari_scsi_template.can_queue = setup_can_queue; + + if (setup_cmd_per_lun > 0) + atari_scsi_template.cmd_per_lun = setup_cmd_per_lun; + + /* Leave sg_tablesize at 0 on a Falcon! */ + if (IS_A_TT() && setup_sg_tablesize >= 0) + atari_scsi_template.sg_tablesize = setup_sg_tablesize; + + if (setup_hostid >= 0) { + atari_scsi_template.this_id = setup_hostid & 7; + } else { + /* Test if a host id is set in the NVRam */ + if (ATARIHW_PRESENT(TT_CLK) && nvram_check_checksum()) { + unsigned char b = nvram_read_byte(14); + + /* Arbitration enabled? (for TOS) + * If yes, use configured host ID + */ + if (b & 0x80) + atari_scsi_template.this_id = b & 7; + } + } + +#ifdef SUPPORT_TAGS + if (setup_use_tagged_queuing < 0) + setup_use_tagged_queuing = 0; +#endif + +#ifdef REAL_DMA + /* If running on a Falcon and if there's TT-Ram (i.e., more than one + * memory block, since there's always ST-Ram in a Falcon), then + * allocate a STRAM_BUFFER_SIZE byte dribble buffer for transfers + * from/to alternative Ram. + */ + if (ATARIHW_PRESENT(ST_SCSI) && !ATARIHW_PRESENT(EXTD_DMA) && + m68k_num_memory > 1) { + atari_dma_buffer = atari_stram_alloc(STRAM_BUFFER_SIZE, "SCSI"); + if (!atari_dma_buffer) { + pr_err(PFX "can't allocate ST-RAM double buffer\n"); + return -ENOMEM; + } + atari_dma_phys_buffer = atari_stram_to_phys(atari_dma_buffer); + atari_dma_orig_addr = 0; + } +#endif + + instance = scsi_host_alloc(&atari_scsi_template, + sizeof(struct NCR5380_hostdata)); + if (!instance) { + error = -ENOMEM; + goto fail_alloc; + } + atari_scsi_host = instance; + +#ifdef CONFIG_ATARI_SCSI_RESET_BOOT + atari_scsi_reset_boot(); +#endif + + if (IS_A_TT()) + instance->irq = IRQ_TT_MFP_SCSI; + else + instance->irq = IRQ_NONE; + + NCR5380_init(instance, 0); + + if (IS_A_TT()) { + error = request_irq(instance->irq, scsi_tt_intr, 0, + "NCR5380", instance); + if (error) { + pr_err(PFX "request irq %d failed, aborting\n", + instance->irq); + goto fail_irq; + } + tt_mfp.active_edge |= 0x80; /* SCSI int on L->H */ +#ifdef REAL_DMA + tt_scsi_dma.dma_ctrl = 0; + atari_dma_residual = 0; + + /* While the read overruns (described by Drew Eckhardt in + * NCR5380.c) never happened on TTs, they do in fact on the + * Medusa (This was the cause why SCSI didn't work right for + * so long there.) Since handling the overruns slows down + * a bit, I turned the #ifdef's into a runtime condition. + * + * In principle it should be sufficient to do max. 1 byte with + * PIO, but there is another problem on the Medusa with the DMA + * rest data register. So 'atari_read_overruns' is currently set + * to 4 to avoid having transfers that aren't a multiple of 4. + * If the rest data bug is fixed, this can be lowered to 1. + */ + if (MACH_IS_MEDUSA) + atari_read_overruns = 4; +#endif + } else { + /* Nothing to do for the interrupt: the ST-DMA is initialized + * already. + */ +#ifdef REAL_DMA + atari_dma_residual = 0; + atari_dma_active = 0; + atari_dma_stram_mask = (ATARIHW_PRESENT(EXTD_DMA) ? 0x00000000 + : 0xff000000); +#endif + } + + error = scsi_add_host(instance, NULL); + if (error) + goto fail_host; + + platform_set_drvdata(pdev, instance); + + scsi_scan_host(instance); + return 0; + +fail_host: + if (instance->irq != IRQ_NONE) + free_irq(instance->irq, instance); +fail_irq: + NCR5380_exit(instance); + scsi_host_put(instance); +fail_alloc: + if (atari_dma_buffer) + atari_stram_free(atari_dma_buffer); + return error; +} + +static int __exit atari_scsi_remove(struct platform_device *pdev) +{ + struct Scsi_Host *instance = platform_get_drvdata(pdev); + + scsi_remove_host(instance); + if (instance->irq != IRQ_NONE) + free_irq(instance->irq, instance); + NCR5380_exit(instance); + scsi_host_put(instance); + if (atari_dma_buffer) + atari_stram_free(atari_dma_buffer); + return 0; +} + +static struct platform_driver atari_scsi_driver = { + .remove = __exit_p(atari_scsi_remove), + .driver = { + .name = DRV_MODULE_NAME, + .owner = THIS_MODULE, + }, +}; -#include "scsi_module.c" +module_platform_driver_probe(atari_scsi_driver, atari_scsi_probe); +MODULE_ALIAS("platform:" DRV_MODULE_NAME); MODULE_LICENSE("GPL"); Index: linux/drivers/scsi/atari_scsi.h =================================================================== --- linux.orig/drivers/scsi/atari_scsi.h 2014-10-02 16:56:10.000000000 +1000 +++ linux/drivers/scsi/atari_scsi.h 2014-10-02 16:56:21.000000000 +1000 @@ -18,23 +18,6 @@ /* (I_HAVE_OVERRUNS stuff removed) */ #ifndef ASM -/* The values for CMD_PER_LUN and CAN_QUEUE are somehow arbitrary. Higher - * values should work, too; try it! (but cmd_per_lun costs memory!) */ - -/* But there seems to be a bug somewhere that requires CAN_QUEUE to be - * 2*CMD_PER_LUN. At least on a TT, no spurious timeouts seen since - * changed CMD_PER_LUN... */ - -/* Note: The Falcon currently uses 8/1 setting due to unsolved problems with - * cmd_per_lun != 1 */ - -#define ATARI_TT_CAN_QUEUE 16 -#define ATARI_TT_CMD_PER_LUN 8 -#define ATARI_TT_SG_TABLESIZE SG_ALL - -#define ATARI_FALCON_CAN_QUEUE 8 -#define ATARI_FALCON_CMD_PER_LUN 1 -#define ATARI_FALCON_SG_TABLESIZE SG_NONE #define NCR5380_implementation_fields /* none */