From: Markus Pargmann <mpa@pengutronix.de>
To: Jonathan Cameron <jic23@kernel.org>
Cc: Vlad Dogaru <vlad.dogaru@intel.com>,
Paul Bolle <pebolle@tiscali.nl>,
linux-iio@vger.kernel.org, linux-kernel@vger.kernel.org,
kernel@pengutronix.de,
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Subject: Re: [PATCH v2 1/6] iio: bmg160: Use i2c regmap instead of direct i2c access
Date: Sun, 9 Aug 2015 08:47:52 +0200 [thread overview]
Message-ID: <20150809064752.GV19600@pengutronix.de> (raw)
In-Reply-To: <1438686179-18635-2-git-send-email-mpa@pengutronix.de>
[-- Attachment #1: Type: text/plain, Size: 17144 bytes --]
On Tue, Aug 04, 2015 at 01:02:54PM +0200, Markus Pargmann wrote:
> This patch introduces regmap usage into the driver. This is done to
> later easily support the SPI interface of this chip.
>
> Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
> ---
> drivers/iio/gyro/Kconfig | 2 +
> drivers/iio/gyro/bmg160.c | 200 +++++++++++++++++++++-------------------------
> 2 files changed, 91 insertions(+), 111 deletions(-)
>
> diff --git a/drivers/iio/gyro/Kconfig b/drivers/iio/gyro/Kconfig
> index 8d2439345673..b44984b3bb24 100644
> --- a/drivers/iio/gyro/Kconfig
> +++ b/drivers/iio/gyro/Kconfig
> @@ -55,6 +55,8 @@ config BMG160
> depends on I2C
> select IIO_BUFFER
> select IIO_TRIGGERED_BUFFER
> + select REGMAP
> + select REGMAP_I2C
> help
> Say yes here to build support for Bosch BMG160 Tri-axis Gyro Sensor
> driver. This driver also supports BMI055 gyroscope.
> diff --git a/drivers/iio/gyro/bmg160.c b/drivers/iio/gyro/bmg160.c
> index 460bf715d541..626f5c98dde8 100644
> --- a/drivers/iio/gyro/bmg160.c
> +++ b/drivers/iio/gyro/bmg160.c
> @@ -28,6 +28,7 @@
> #include <linux/iio/events.h>
> #include <linux/iio/trigger_consumer.h>
> #include <linux/iio/triggered_buffer.h>
> +#include <linux/regmap.h>
>
> #define BMG160_DRV_NAME "bmg160"
> #define BMG160_IRQ_NAME "bmg160_event"
> @@ -98,6 +99,7 @@
>
> struct bmg160_data {
> struct i2c_client *client;
> + struct regmap *regmap;
> struct iio_trigger *dready_trig;
> struct iio_trigger *motion_trig;
> struct mutex mutex;
> @@ -134,12 +136,19 @@ static const struct {
> { 133, BMG160_RANGE_250DPS},
> { 66, BMG160_RANGE_125DPS} };
>
> +struct regmap_config bmg160_regmap_i2c_conf = {
> + .reg_bits = 8,
> + .val_bits = 8,
> +
> + .use_single_rw = true,
This should not be necessary, we should be able to read multiple
registers at once. This is the same for the spi regmap config.
Also a max_register is missing. Will fix it.
Regards,
Markus
> + .cache_type = REGCACHE_NONE,
> +};
> +
> static int bmg160_set_mode(struct bmg160_data *data, u8 mode)
> {
> int ret;
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_PMU_LPW, mode);
> + ret = regmap_write(data->regmap, BMG160_REG_PMU_LPW, mode);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_pmu_lpw\n");
> return ret;
> @@ -169,8 +178,7 @@ static int bmg160_set_bw(struct bmg160_data *data, int val)
> if (bw_bits < 0)
> return bw_bits;
>
> - ret = i2c_smbus_write_byte_data(data->client, BMG160_REG_PMU_BW,
> - bw_bits);
> + ret = regmap_write(data->regmap, BMG160_REG_PMU_BW, bw_bits);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_pmu_bw\n");
> return ret;
> @@ -184,16 +192,17 @@ static int bmg160_set_bw(struct bmg160_data *data, int val)
> static int bmg160_chip_init(struct bmg160_data *data)
> {
> int ret;
> + unsigned int val;
>
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_CHIP_ID);
> + ret = regmap_read(data->regmap, BMG160_REG_CHIP_ID, &val);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading reg_chip_id\n");
> return ret;
> }
>
> - dev_dbg(&data->client->dev, "Chip Id %x\n", ret);
> - if (ret != BMG160_CHIP_ID_VAL) {
> - dev_err(&data->client->dev, "invalid chip %x\n", ret);
> + dev_dbg(&data->client->dev, "Chip Id %x\n", val);
> + if (val != BMG160_CHIP_ID_VAL) {
> + dev_err(&data->client->dev, "invalid chip %x\n", val);
> return -ENODEV;
> }
>
> @@ -210,40 +219,31 @@ static int bmg160_chip_init(struct bmg160_data *data)
> return ret;
>
> /* Set Default Range */
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_RANGE,
> - BMG160_RANGE_500DPS);
> + ret = regmap_write(data->regmap, BMG160_REG_RANGE, BMG160_RANGE_500DPS);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_range\n");
> return ret;
> }
> data->dps_range = BMG160_RANGE_500DPS;
>
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_SLOPE_THRES);
> + ret = regmap_read(data->regmap, BMG160_REG_SLOPE_THRES, &val);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading reg_slope_thres\n");
> return ret;
> }
> - data->slope_thres = ret;
> + data->slope_thres = val;
>
> /* Set default interrupt mode */
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_EN_1);
> - if (ret < 0) {
> - dev_err(&data->client->dev, "Error reading reg_int_en_1\n");
> - return ret;
> - }
> - ret &= ~BMG160_INT1_BIT_OD;
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_1, ret);
> + ret = regmap_update_bits(data->regmap, BMG160_REG_INT_EN_1,
> + BMG160_INT1_BIT_OD, 0);
> if (ret < 0) {
> - dev_err(&data->client->dev, "Error writing reg_int_en_1\n");
> + dev_err(&data->client->dev, "Error updating bits in reg_int_en_1\n");
> return ret;
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_motion_intr\n");
> @@ -284,41 +284,28 @@ static int bmg160_setup_any_motion_interrupt(struct bmg160_data *data,
> int ret;
>
> /* Enable/Disable INT_MAP0 mapping */
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_MAP_0);
> - if (ret < 0) {
> - dev_err(&data->client->dev, "Error reading reg_int_map0\n");
> - return ret;
> - }
> - if (status)
> - ret |= BMG160_INT_MAP_0_BIT_ANY;
> - else
> - ret &= ~BMG160_INT_MAP_0_BIT_ANY;
> -
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_MAP_0,
> - ret);
> + ret = regmap_update_bits(data->regmap, BMG160_REG_INT_MAP_0,
> + BMG160_INT_MAP_0_BIT_ANY,
> + (status ? BMG160_INT_MAP_0_BIT_ANY : 0));
> if (ret < 0) {
> - dev_err(&data->client->dev, "Error writing reg_int_map0\n");
> + dev_err(&data->client->dev, "Error updating bits reg_int_map0\n");
> return ret;
> }
>
> /* Enable/Disable slope interrupts */
> if (status) {
> /* Update slope thres */
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_SLOPE_THRES,
> - data->slope_thres);
> + ret = regmap_write(data->regmap, BMG160_REG_SLOPE_THRES,
> + data->slope_thres);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_slope_thres\n");
> return ret;
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_MOTION_INTR,
> - BMG160_INT_MOTION_X |
> - BMG160_INT_MOTION_Y |
> - BMG160_INT_MOTION_Z);
> + ret = regmap_write(data->regmap, BMG160_REG_MOTION_INTR,
> + BMG160_INT_MOTION_X | BMG160_INT_MOTION_Y |
> + BMG160_INT_MOTION_Z);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_motion_intr\n");
> @@ -331,10 +318,10 @@ static int bmg160_setup_any_motion_interrupt(struct bmg160_data *data,
> * to set latched mode, we will be flooded anyway with INTR
> */
> if (!data->dready_trigger_on) {
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap,
> + BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_rst_latch\n");
> @@ -342,14 +329,12 @@ static int bmg160_setup_any_motion_interrupt(struct bmg160_data *data,
> }
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_0,
> - BMG160_DATA_ENABLE_INT);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0,
> + BMG160_DATA_ENABLE_INT);
>
> - } else
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_0,
> - 0);
> + } else {
> + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0, 0);
> + }
>
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_int_en0\n");
> @@ -365,55 +350,39 @@ static int bmg160_setup_new_data_interrupt(struct bmg160_data *data,
> int ret;
>
> /* Enable/Disable INT_MAP1 mapping */
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_MAP_1);
> - if (ret < 0) {
> - dev_err(&data->client->dev, "Error reading reg_int_map1\n");
> - return ret;
> - }
> -
> - if (status)
> - ret |= BMG160_INT_MAP_1_BIT_NEW_DATA;
> - else
> - ret &= ~BMG160_INT_MAP_1_BIT_NEW_DATA;
> -
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_MAP_1,
> - ret);
> + ret = regmap_update_bits(data->regmap, BMG160_REG_INT_MAP_1,
> + BMG160_INT_MAP_1_BIT_NEW_DATA,
> + (status ? BMG160_INT_MAP_1_BIT_NEW_DATA : 0));
> if (ret < 0) {
> - dev_err(&data->client->dev, "Error writing reg_int_map1\n");
> + dev_err(&data->client->dev, "Error updating bits in reg_int_map1\n");
> return ret;
> }
>
> if (status) {
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_NON_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_NON_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_rst_latch\n");
> return ret;
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_0,
> - BMG160_DATA_ENABLE_INT);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0,
> + BMG160_DATA_ENABLE_INT);
>
> } else {
> /* Restore interrupt mode */
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_rst_latch\n");
> return ret;
> }
>
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_EN_0,
> - 0);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0, 0);
> }
>
> if (ret < 0) {
> @@ -444,10 +413,8 @@ static int bmg160_set_scale(struct bmg160_data *data, int val)
>
> for (i = 0; i < ARRAY_SIZE(bmg160_scale_table); ++i) {
> if (bmg160_scale_table[i].scale == val) {
> - ret = i2c_smbus_write_byte_data(
> - data->client,
> - BMG160_REG_RANGE,
> - bmg160_scale_table[i].dps_range);
> + ret = regmap_write(data->regmap, BMG160_REG_RANGE,
> + bmg160_scale_table[i].dps_range);
> if (ret < 0) {
> dev_err(&data->client->dev,
> "Error writing reg_range\n");
> @@ -464,6 +431,7 @@ static int bmg160_set_scale(struct bmg160_data *data, int val)
> static int bmg160_get_temp(struct bmg160_data *data, int *val)
> {
> int ret;
> + unsigned int raw_val;
>
> mutex_lock(&data->mutex);
> ret = bmg160_set_power_state(data, true);
> @@ -472,7 +440,7 @@ static int bmg160_get_temp(struct bmg160_data *data, int *val)
> return ret;
> }
>
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_TEMP);
> + ret = regmap_read(data->regmap, BMG160_REG_TEMP, &raw_val);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading reg_temp\n");
> bmg160_set_power_state(data, false);
> @@ -480,7 +448,7 @@ static int bmg160_get_temp(struct bmg160_data *data, int *val)
> return ret;
> }
>
> - *val = sign_extend32(ret, 7);
> + *val = sign_extend32(raw_val, 7);
> ret = bmg160_set_power_state(data, false);
> mutex_unlock(&data->mutex);
> if (ret < 0)
> @@ -492,6 +460,7 @@ static int bmg160_get_temp(struct bmg160_data *data, int *val)
> static int bmg160_get_axis(struct bmg160_data *data, int axis, int *val)
> {
> int ret;
> + unsigned int raw_val;
>
> mutex_lock(&data->mutex);
> ret = bmg160_set_power_state(data, true);
> @@ -500,7 +469,8 @@ static int bmg160_get_axis(struct bmg160_data *data, int axis, int *val)
> return ret;
> }
>
> - ret = i2c_smbus_read_word_data(data->client, BMG160_AXIS_TO_REG(axis));
> + ret = regmap_bulk_read(data->regmap, BMG160_AXIS_TO_REG(axis), &raw_val,
> + 2);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading axis %d\n", axis);
> bmg160_set_power_state(data, false);
> @@ -508,7 +478,7 @@ static int bmg160_get_axis(struct bmg160_data *data, int axis, int *val)
> return ret;
> }
>
> - *val = sign_extend32(ret, 15);
> + *val = sign_extend32(raw_val, 15);
> ret = bmg160_set_power_state(data, false);
> mutex_unlock(&data->mutex);
> if (ret < 0)
> @@ -807,12 +777,13 @@ static irqreturn_t bmg160_trigger_handler(int irq, void *p)
> struct iio_dev *indio_dev = pf->indio_dev;
> struct bmg160_data *data = iio_priv(indio_dev);
> int bit, ret, i = 0;
> + unsigned int val;
>
> mutex_lock(&data->mutex);
> for_each_set_bit(bit, indio_dev->active_scan_mask,
> indio_dev->masklength) {
> - ret = i2c_smbus_read_word_data(data->client,
> - BMG160_AXIS_TO_REG(bit));
> + ret = regmap_bulk_read(data->regmap, BMG160_AXIS_TO_REG(bit),
> + &val, 2);
> if (ret < 0) {
> mutex_unlock(&data->mutex);
> goto err;
> @@ -840,10 +811,9 @@ static int bmg160_trig_try_reen(struct iio_trigger *trig)
> return 0;
>
> /* Set latched mode interrupt and clear any latched interrupt */
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error writing reg_rst_latch\n");
> return ret;
> @@ -907,33 +877,34 @@ static irqreturn_t bmg160_event_handler(int irq, void *private)
> struct bmg160_data *data = iio_priv(indio_dev);
> int ret;
> int dir;
> + unsigned int val;
>
> - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_STATUS_2);
> + ret = regmap_read(data->regmap, BMG160_REG_INT_STATUS_2, &val);
> if (ret < 0) {
> dev_err(&data->client->dev, "Error reading reg_int_status2\n");
> goto ack_intr_status;
> }
>
> - if (ret & 0x08)
> + if (val & 0x08)
> dir = IIO_EV_DIR_RISING;
> else
> dir = IIO_EV_DIR_FALLING;
>
> - if (ret & BMG160_ANY_MOTION_BIT_X)
> + if (val & BMG160_ANY_MOTION_BIT_X)
> iio_push_event(indio_dev, IIO_MOD_EVENT_CODE(IIO_ANGL_VEL,
> 0,
> IIO_MOD_X,
> IIO_EV_TYPE_ROC,
> dir),
> iio_get_time_ns());
> - if (ret & BMG160_ANY_MOTION_BIT_Y)
> + if (val & BMG160_ANY_MOTION_BIT_Y)
> iio_push_event(indio_dev, IIO_MOD_EVENT_CODE(IIO_ANGL_VEL,
> 0,
> IIO_MOD_Y,
> IIO_EV_TYPE_ROC,
> dir),
> iio_get_time_ns());
> - if (ret & BMG160_ANY_MOTION_BIT_Z)
> + if (val & BMG160_ANY_MOTION_BIT_Z)
> iio_push_event(indio_dev, IIO_MOD_EVENT_CODE(IIO_ANGL_VEL,
> 0,
> IIO_MOD_Z,
> @@ -943,10 +914,9 @@ static irqreturn_t bmg160_event_handler(int irq, void *private)
>
> ack_intr_status:
> if (!data->dready_trigger_on) {
> - ret = i2c_smbus_write_byte_data(data->client,
> - BMG160_REG_INT_RST_LATCH,
> - BMG160_INT_MODE_LATCH_INT |
> - BMG160_INT_MODE_LATCH_RESET);
> + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH,
> + BMG160_INT_MODE_LATCH_INT |
> + BMG160_INT_MODE_LATCH_RESET);
> if (ret < 0)
> dev_err(&data->client->dev,
> "Error writing reg_rst_latch\n");
> @@ -1038,6 +1008,14 @@ static int bmg160_probe(struct i2c_client *client,
> struct iio_dev *indio_dev;
> int ret;
> const char *name = NULL;
> + struct regmap *regmap;
> +
> + regmap = devm_regmap_init_i2c(client, &bmg160_regmap_i2c_conf);
> + if (IS_ERR(regmap)) {
> + dev_err(&client->dev, "Failed to register i2c regmap %d\n",
> + (int)PTR_ERR(regmap));
> + return PTR_ERR(regmap);
> + }
>
> indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> if (!indio_dev)
> --
> 2.1.4
>
>
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
next prev parent reply other threads:[~2015-08-09 6:47 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-08-04 11:02 [PATCH v2 0/6] iio: bmg160: Add SPI connection Markus Pargmann
2015-08-04 11:02 ` [PATCH v2 1/6] iio: bmg160: Use i2c regmap instead of direct i2c access Markus Pargmann
2015-08-09 6:47 ` Markus Pargmann [this message]
2015-08-04 11:02 ` [PATCH v2 2/6] iio: bmg160: Remove i2c_client from data struct Markus Pargmann
2015-08-04 11:02 ` [PATCH v2 3/6] iio: bmg160: Use generic dev_drvdata Markus Pargmann
2015-08-04 11:02 ` [PATCH v2 4/6] iio: bmg160: Remove remaining uses of i2c_client Markus Pargmann
2015-08-04 11:02 ` [PATCH v2 5/6] iio: bmg160: Separate i2c and core driver Markus Pargmann
2015-08-08 16:11 ` Jonathan Cameron
2015-08-09 6:45 ` Markus Pargmann
2015-08-04 11:02 ` [PATCH v2 6/6] iio: bmg160: Add SPI driver Markus Pargmann
2015-08-10 13:38 ` Markus Pargmann
2015-08-08 16:12 ` [PATCH v2 0/6] iio: bmg160: Add SPI connection Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150809064752.GV19600@pengutronix.de \
--to=mpa@pengutronix.de \
--cc=jic23@kernel.org \
--cc=kernel@pengutronix.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=pebolle@tiscali.nl \
--cc=srinivas.pandruvada@linux.intel.com \
--cc=vlad.dogaru@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.