On Mon, Oct 19, 2015 at 12:49:03PM +0200, Peter Rosin wrote:
> On 2015-10-19 10:51, Ludovic Desroches wrote:
> > Hi Peter,
> > 
> > On Fri, Oct 16, 2015 at 11:08:42AM +0200, Peter Rosin wrote:
> >> On 2015-10-16 01:47, Peter Rosin wrote:
> >>> On 2015-10-14 07:43, Ludovic Desroches wrote:
> >>>> On Tue, Oct 13, 2015 at 08:01:34PM +0200, Peter Rosin wrote:
> >>>>> On 2015-10-13 18:47, Cyrille Pitchen wrote:
> >>>>>> Le 13/10/2015 17:19, Peter Rosin a écrit :
> >>>>>>> On 2015-10-13 16:21, Ludovic Desroches wrote:
> > 
> > [...]
> > 
> >>> I have started to get this when I run with this patch:
> >>>
> >>> [   73.310000] at91_i2c f0014000.i2c: RXRDY still set!
> >>> [  198.200000] at91_i2c f0014000.i2c: RXRDY still set!
> >>> [  509.880000] at91_i2c f0014000.i2c: RXRDY still set!
> >>> [  615.750000] at91_i2c f0014000.i2c: RXRDY still set!
> >>> [  617.750000] at91_i2c f0014000.i2c: RXRDY still set!
> >>> [ 1766.640000] at91_i2c f0014000.i2c: RXRDY still set!
> >>> [ 2035.380000] at91_i2c f0014000.i2c: RXRDY still set!
> >>> [ 2227.190000] at91_i2c f0014000.i2c: RXRDY still set!
> >>> [ 2313.100000] at91_i2c f0014000.i2c: RXRDY still set!
> >>>
> >>> My USB serial dongle was hung which was why I didn't notice until just now.
> >>>
> >>> This is probably not when communication with the eeprom though, and certainly not
> >>> writing to it, but perhpaps when polling the temperature (using the jc42 driver).
> >>> I'll investigate further in the morning to see if I can pinpoint it.
> >>
> >> Yep, it's the jc42 accesses that triggers this (to the same chip as the
> >> eeprom, but a different block of transistors I suppose).
> >>
> >> Looking at the i2c bus, the accesses normally go like this:
> >>
> >> [0.000000] S 0x18 W 0x05 S 0x18 R 0xc1 0xbe NACK P
> >> [0.000521] S 0x18 W 0x04 S 0x18 R 0x00 0x00 NACK P
> >> [0.001024] S 0x18 W 0x03 S 0x18 R 0x00 0x00 NACK P
> >> [0.001524] S 0x18 W 0x02 S 0x18 R 0x00 0x00 NACK P
> >> [0.196991] S 0x18 W 0x05 S 0x18 R 0xc1 0xbe NACK P
> >> [0.197514] S 0x18 W 0x04 S 0x18 R 0x00 0x00 NACK P
> >> [0.198019] S 0x18 W 0x03 S 0x18 R 0x00 0x00 NACK P
> >> [0.198520] S 0x18 W 0x02 S 0x18 R 0x00 0x00 NACK P
> >>
> >> I.e. chunks of four transfers every ~200 ms (I removed the 1Hz rate
> >> limiter in the jc42 driver to get more frequent incidents).
> >>
> >> But when the diagnostic (RXRDY still set!) is output it continues
> >> with this:
> >>
> >> [0.399755] S 0x18 W 0x05 S 0x18 R 0xc1 0xbe NACK P
> >> [0.404998] S 0x18 W 0x04 S 0x18 R 0x00 0x00 NACK P
> >> [0.405508] S 0x18 W 0x03 S 0x18 R 0x00 0x00 NACK P
> >> [0.406008] S 0x18 W 0x02 S 0x18 R 0x00 0x00 NACK P
> >>
> >> Notice the ~5 ms delay (about the time it should take to output
> >> the diagnostic at 115200 baud) after the access to register 0x05
> >> at 0.399755.
> >>
> >> This is the only thing that I can observe on the bus, so it appears
> >> to be harmless.
> >>
> >> It appears that the i2c access at 0.399755 finds the TWI
> >> registers in an odd state, but nothing from the access at
> >> 0.198520 appears to have gone wrong. Is this a race? Anyway,
> >> the diagnostic is pretty frequent and annoying. printk_once?
> > 
> > I'll try to reproduce it on my side. The only issue you have is having
> > the message about RXRDY? I mean no issue with i2c transfers?
> 
> Exactly, the only issue is the message, the bus looks good and transfers
> work as they should AFAICT.
> > It is not the possible bug we had in mind, this bug will prevent the
> > master device to release the i2c bus. It will stop the transfer but
> > without sending a stop on the bus.
> 
> Agreed, this is not about the extra frame caused by the spurious write
> to the THR register. This is something else.
> 
> One suspicion is that the driver gets an unexpected irq from its own
> NACK (the one that it puts out to end the read) and races with the
> expected interrupt at TXCOMP?
>

I have discussed with the designer of this IP. So the NACK flag is only
used for 'real' nack not protocol ones.

Concerning the read issue, it have attached a patch (apply it on top of
Cyrille's patch). Could you have a try? I have reproduced your issue only one
time so it's hard for me to tell if it works well or not.

Regards

Ludovic