* [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards
@ 2015-11-15 21:36 Ondrej Zary
2015-11-15 21:36 ` [PATCH 2/2] ipg: Remove ipg driver Ondrej Zary
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Ondrej Zary @ 2015-11-15 21:36 UTC (permalink / raw)
To: netdev; +Cc: Francois Romieu, David Miller, Kernel development list
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
---
drivers/net/ethernet/dlink/Kconfig | 5 ++--
drivers/net/ethernet/dlink/dl2k.c | 55 ++++++++++++++++++++++++++++++++++--
drivers/net/ethernet/dlink/dl2k.h | 15 +++++++++-
3 files changed, 69 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/dlink/Kconfig b/drivers/net/ethernet/dlink/Kconfig
index f6e858d..ebdc832 100644
--- a/drivers/net/ethernet/dlink/Kconfig
+++ b/drivers/net/ethernet/dlink/Kconfig
@@ -17,15 +17,16 @@ config NET_VENDOR_DLINK
if NET_VENDOR_DLINK
config DL2K
- tristate "DL2000/TC902x-based Gigabit Ethernet support"
+ tristate "DL2000/TC902x/IP1000A-based Gigabit Ethernet support"
depends on PCI
select CRC32
---help---
- This driver supports DL2000/TC902x-based Gigabit ethernet cards,
+ This driver supports DL2000/TC902x/IP1000A-based Gigabit ethernet cards,
which includes
D-Link DGE-550T Gigabit Ethernet Adapter.
D-Link DL2000-based Gigabit Ethernet Adapter.
Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
+ ICPlus IP1000A-based cards
To compile this driver as a module, choose M here: the
module will be called dl2k.
diff --git a/drivers/net/ethernet/dlink/dl2k.c b/drivers/net/ethernet/dlink/dl2k.c
index cf0a5fc..ccca479 100644
--- a/drivers/net/ethernet/dlink/dl2k.c
+++ b/drivers/net/ethernet/dlink/dl2k.c
@@ -253,6 +253,19 @@ rio_probe1 (struct pci_dev *pdev, const struct pci_device_id *ent)
if (err)
goto err_out_unmap_rx;
+ if (np->chip_id == CHIP_IP1000A &&
+ (np->pdev->revision == 0x40 || np->pdev->revision == 0x41)) {
+ /* PHY magic taken from ipg driver, undocumented registers */
+ mii_write(dev, np->phy_addr, 31, 0x0001);
+ mii_write(dev, np->phy_addr, 27, 0x01e0);
+ mii_write(dev, np->phy_addr, 31, 0x0002);
+ mii_write(dev, np->phy_addr, 27, 0xeb8e);
+ mii_write(dev, np->phy_addr, 31, 0x0000);
+ mii_write(dev, np->phy_addr, 30, 0x005e);
+ /* advertise 1000BASE-T half & full duplex, prefer MASTER */
+ mii_write(dev, np->phy_addr, MII_CTRL1000, 0x0700);
+ }
+
/* Fiber device? */
np->phy_media = (dr16(ASICCtrl) & PhyMedia) ? 1 : 0;
np->link_status = 0;
@@ -361,6 +374,11 @@ parse_eeprom (struct net_device *dev)
for (i = 0; i < 6; i++)
dev->dev_addr[i] = psrom->mac_addr[i];
+ if (np->chip_id == CHIP_IP1000A) {
+ np->led_mode = psrom->led_mode;
+ return 0;
+ }
+
if (np->pdev->vendor != PCI_VENDOR_ID_DLINK) {
return 0;
}
@@ -406,6 +424,28 @@ parse_eeprom (struct net_device *dev)
return 0;
}
+static void rio_set_led_mode(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->ioaddr;
+ u32 mode;
+
+ if (np->chip_id != CHIP_IP1000A)
+ return;
+
+ mode = dr32(ASICCtrl);
+ mode &= ~(IPG_AC_LED_MODE_BIT_1 | IPG_AC_LED_MODE | IPG_AC_LED_SPEED);
+
+ if (np->led_mode & 0x01)
+ mode |= IPG_AC_LED_MODE;
+ if (np->led_mode & 0x02)
+ mode |= IPG_AC_LED_MODE_BIT_1;
+ if (np->led_mode & 0x08)
+ mode |= IPG_AC_LED_SPEED;
+
+ dw32(ASICCtrl, mode);
+}
+
static int
rio_open (struct net_device *dev)
{
@@ -424,6 +464,8 @@ rio_open (struct net_device *dev)
GlobalReset | DMAReset | FIFOReset | NetworkReset | HostReset);
mdelay(10);
+ rio_set_led_mode(dev);
+
/* DebugCtrl bit 4, 5, 9 must set */
dw32(DebugCtrl, dr32(DebugCtrl) | 0x0230);
@@ -433,9 +475,13 @@ rio_open (struct net_device *dev)
alloc_list (dev);
- /* Get station address */
- for (i = 0; i < 6; i++)
- dw8(StationAddr0 + i, dev->dev_addr[i]);
+ /* Set station address */
+ /* 16 or 32-bit access is required by TC9020 datasheet but 8-bit works
+ * too. However, it doesn't work on IP1000A so we use 16-bit access.
+ */
+ for (i = 0; i < 3; i++)
+ dw16(StationAddr0 + 2 * i,
+ cpu_to_le16(((u16 *)dev->dev_addr)[i]));
set_multicast (dev);
if (np->coalesce) {
@@ -780,6 +826,7 @@ tx_error (struct net_device *dev, int tx_status)
break;
mdelay (1);
}
+ rio_set_led_mode(dev);
rio_free_tx (dev, 1);
/* Reset TFDListPtr */
dw32(TFDListPtr0, np->tx_ring_dma +
@@ -799,6 +846,7 @@ tx_error (struct net_device *dev, int tx_status)
break;
mdelay (1);
}
+ rio_set_led_mode(dev);
/* Let TxStartThresh stay default value */
}
/* Maximum Collisions */
@@ -965,6 +1013,7 @@ rio_error (struct net_device *dev, int int_status)
dev->name, int_status);
dw16(ASICCtrl + 2, GlobalReset | HostReset);
mdelay (500);
+ rio_set_led_mode(dev);
}
}
diff --git a/drivers/net/ethernet/dlink/dl2k.h b/drivers/net/ethernet/dlink/dl2k.h
index 23c07b0..8f4f612 100644
--- a/drivers/net/ethernet/dlink/dl2k.h
+++ b/drivers/net/ethernet/dlink/dl2k.h
@@ -211,6 +211,10 @@ enum ASICCtrl_HiWord_bits {
ResetBusy = 0x0400,
};
+#define IPG_AC_LED_MODE BIT(14)
+#define IPG_AC_LED_SPEED BIT(27)
+#define IPG_AC_LED_MODE_BIT_1 BIT(29)
+
/* Transmit Frame Control bits */
enum TFC_bits {
DwordAlign = 0x00000000,
@@ -332,7 +336,10 @@ typedef struct t_SROM {
u16 asic_ctrl; /* 0x02 */
u16 sub_vendor_id; /* 0x04 */
u16 sub_system_id; /* 0x06 */
- u16 reserved1[12]; /* 0x08-0x1f */
+ u16 pci_base_1; /* 0x08 (IP1000A only) */
+ u16 pci_base_2; /* 0x0a (IP1000A only) */
+ u16 led_mode; /* 0x0c (IP1000A only) */
+ u16 reserved1[9]; /* 0x0e-0x1f */
u8 mac_addr[6]; /* 0x20-0x25 */
u8 reserved2[10]; /* 0x26-0x2f */
u8 sib[204]; /* 0x30-0xfb */
@@ -397,6 +404,7 @@ struct netdev_private {
u16 advertising; /* NWay media advertisement */
u16 negotiate; /* Negotiated media */
int phy_addr; /* PHY addresses. */
+ u16 led_mode; /* LED mode read from EEPROM (IP1000A only) */
};
/* The station address location in the EEPROM. */
@@ -407,10 +415,15 @@ struct netdev_private {
class_mask of the class are honored during the comparison.
driver_data Data private to the driver.
*/
+#define CHIP_IP1000A 1
static const struct pci_device_id rio_pci_tbl[] = {
{0x1186, 0x4000, PCI_ANY_ID, PCI_ANY_ID, },
{0x13f0, 0x1021, PCI_ANY_ID, PCI_ANY_ID, },
+ { PCI_VDEVICE(SUNDANCE, 0x1023), CHIP_IP1000A },
+ { PCI_VDEVICE(SUNDANCE, 0x2021), CHIP_IP1000A },
+ { PCI_VDEVICE(DLINK, 0x9021), CHIP_IP1000A },
+ { PCI_VDEVICE(DLINK, 0x4020), CHIP_IP1000A },
{ }
};
MODULE_DEVICE_TABLE (pci, rio_pci_tbl);
--
Ondrej Zary
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/2] ipg: Remove ipg driver
2015-11-15 21:36 [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards Ondrej Zary
@ 2015-11-15 21:36 ` Ondrej Zary
2015-11-16 22:12 ` David Miller
2015-11-16 8:41 ` [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards Andy Shevchenko
2015-11-16 22:11 ` David Miller
2 siblings, 1 reply; 5+ messages in thread
From: Ondrej Zary @ 2015-11-15 21:36 UTC (permalink / raw)
To: netdev; +Cc: Francois Romieu, David Miller, Kernel development list
Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
---
MAINTAINERS | 7 -
drivers/net/ethernet/Kconfig | 1 -
drivers/net/ethernet/Makefile | 1 -
drivers/net/ethernet/icplus/Kconfig | 13 -
drivers/net/ethernet/icplus/Makefile | 5 -
drivers/net/ethernet/icplus/ipg.c | 2300 ----------------------------------
drivers/net/ethernet/icplus/ipg.h | 748 -----------
7 files changed, 3075 deletions(-)
delete mode 100644 drivers/net/ethernet/icplus/Kconfig
delete mode 100644 drivers/net/ethernet/icplus/Makefile
delete mode 100644 drivers/net/ethernet/icplus/ipg.c
delete mode 100644 drivers/net/ethernet/icplus/ipg.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 7ba7ab7..b683820 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5588,13 +5588,6 @@ M: Juanjo Ciarlante <jjciarla@raiz.uncu.edu.ar>
S: Maintained
F: net/ipv4/netfilter/ipt_MASQUERADE.c
-IP1000A 10/100/1000 GIGABIT ETHERNET DRIVER
-M: Francois Romieu <romieu@fr.zoreil.com>
-M: Sorbica Shieh <sorbica@icplus.com.tw>
-L: netdev@vger.kernel.org
-S: Maintained
-F: drivers/net/ethernet/icplus/ipg.*
-
IPATH DRIVER
M: Mike Marciniszyn <infinipath@intel.com>
L: linux-rdma@vger.kernel.org
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 05aa759..955d06b 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -78,7 +78,6 @@ source "drivers/net/ethernet/ibm/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
source "drivers/net/ethernet/i825xx/Kconfig"
source "drivers/net/ethernet/xscale/Kconfig"
-source "drivers/net/ethernet/icplus/Kconfig"
config JME
tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index ddfc808..4a2ee98 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -41,7 +41,6 @@ obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
obj-$(CONFIG_NET_VENDOR_XSCALE) += xscale/
-obj-$(CONFIG_IP1000) += icplus/
obj-$(CONFIG_JME) += jme.o
obj-$(CONFIG_KORINA) += korina.o
obj-$(CONFIG_LANTIQ_ETOP) += lantiq_etop.o
diff --git a/drivers/net/ethernet/icplus/Kconfig b/drivers/net/ethernet/icplus/Kconfig
deleted file mode 100644
index 14a66e9..0000000
--- a/drivers/net/ethernet/icplus/Kconfig
+++ /dev/null
@@ -1,13 +0,0 @@
-#
-# IC Plus device configuration
-#
-
-config IP1000
- tristate "IP1000 Gigabit Ethernet support"
- depends on PCI
- select MII
- ---help---
- This driver supports IP1000 gigabit Ethernet cards.
-
- To compile this driver as a module, choose M here: the module
- will be called ipg. This is recommended.
diff --git a/drivers/net/ethernet/icplus/Makefile b/drivers/net/ethernet/icplus/Makefile
deleted file mode 100644
index 5bc87c1..0000000
--- a/drivers/net/ethernet/icplus/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# Makefile for the IC Plus device drivers
-#
-
-obj-$(CONFIG_IP1000) += ipg.o
diff --git a/drivers/net/ethernet/icplus/ipg.c b/drivers/net/ethernet/icplus/ipg.c
deleted file mode 100644
index c3b6af8..0000000
--- a/drivers/net/ethernet/icplus/ipg.c
+++ /dev/null
@@ -1,2300 +0,0 @@
-/*
- * ipg.c: Device Driver for the IP1000 Gigabit Ethernet Adapter
- *
- * Copyright (C) 2003, 2007 IC Plus Corp
- *
- * Original Author:
- *
- * Craig Rich
- * Sundance Technology, Inc.
- * www.sundanceti.com
- * craig_rich@sundanceti.com
- *
- * Current Maintainer:
- *
- * Sorbica Shieh.
- * http://www.icplus.com.tw
- * sorbica@icplus.com.tw
- *
- * Jesse Huang
- * http://www.icplus.com.tw
- * jesse@icplus.com.tw
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/crc32.h>
-#include <linux/ethtool.h>
-#include <linux/interrupt.h>
-#include <linux/gfp.h>
-#include <linux/mii.h>
-#include <linux/mutex.h>
-
-#include <asm/div64.h>
-
-#define IPG_RX_RING_BYTES (sizeof(struct ipg_rx) * IPG_RFDLIST_LENGTH)
-#define IPG_TX_RING_BYTES (sizeof(struct ipg_tx) * IPG_TFDLIST_LENGTH)
-#define IPG_RESET_MASK \
- (IPG_AC_GLOBAL_RESET | IPG_AC_RX_RESET | IPG_AC_TX_RESET | \
- IPG_AC_DMA | IPG_AC_FIFO | IPG_AC_NETWORK | IPG_AC_HOST | \
- IPG_AC_AUTO_INIT)
-
-#define ipg_w32(val32, reg) iowrite32((val32), ioaddr + (reg))
-#define ipg_w16(val16, reg) iowrite16((val16), ioaddr + (reg))
-#define ipg_w8(val8, reg) iowrite8((val8), ioaddr + (reg))
-
-#define ipg_r32(reg) ioread32(ioaddr + (reg))
-#define ipg_r16(reg) ioread16(ioaddr + (reg))
-#define ipg_r8(reg) ioread8(ioaddr + (reg))
-
-enum {
- netdev_io_size = 128
-};
-
-#include "ipg.h"
-#define DRV_NAME "ipg"
-
-MODULE_AUTHOR("IC Plus Corp. 2003");
-MODULE_DESCRIPTION("IC Plus IP1000 Gigabit Ethernet Adapter Linux Driver");
-MODULE_LICENSE("GPL");
-
-/*
- * Defaults
- */
-#define IPG_MAX_RXFRAME_SIZE 0x0600
-#define IPG_RXFRAG_SIZE 0x0600
-#define IPG_RXSUPPORT_SIZE 0x0600
-#define IPG_IS_JUMBO false
-
-/*
- * Variable record -- index by leading revision/length
- * Revision/Length(=N*4), Address1, Data1, Address2, Data2,...,AddressN,DataN
- */
-static const unsigned short DefaultPhyParam[] = {
- /* 11/12/03 IP1000A v1-3 rev=0x40 */
- /*--------------------------------------------------------------------------
- (0x4000|(15*4)), 31, 0x0001, 27, 0x01e0, 31, 0x0002, 22, 0x85bd, 24, 0xfff2,
- 27, 0x0c10, 28, 0x0c10, 29, 0x2c10, 31, 0x0003, 23, 0x92f6,
- 31, 0x0000, 23, 0x003d, 30, 0x00de, 20, 0x20e7, 9, 0x0700,
- --------------------------------------------------------------------------*/
- /* 12/17/03 IP1000A v1-4 rev=0x40 */
- (0x4000 | (07 * 4)), 31, 0x0001, 27, 0x01e0, 31, 0x0002, 27, 0xeb8e, 31,
- 0x0000,
- 30, 0x005e, 9, 0x0700,
- /* 01/09/04 IP1000A v1-5 rev=0x41 */
- (0x4100 | (07 * 4)), 31, 0x0001, 27, 0x01e0, 31, 0x0002, 27, 0xeb8e, 31,
- 0x0000,
- 30, 0x005e, 9, 0x0700,
- 0x0000
-};
-
-static const char * const ipg_brand_name[] = {
- "IC PLUS IP1000 1000/100/10 based NIC",
- "Sundance Technology ST2021 based NIC",
- "Tamarack Microelectronics TC9020/9021 based NIC",
- "D-Link NIC IP1000A"
-};
-
-static const struct pci_device_id ipg_pci_tbl[] = {
- { PCI_VDEVICE(SUNDANCE, 0x1023), 0 },
- { PCI_VDEVICE(SUNDANCE, 0x2021), 1 },
- { PCI_VDEVICE(DLINK, 0x9021), 2 },
- { PCI_VDEVICE(DLINK, 0x4020), 3 },
- { 0, }
-};
-
-MODULE_DEVICE_TABLE(pci, ipg_pci_tbl);
-
-static inline void __iomem *ipg_ioaddr(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- return sp->ioaddr;
-}
-
-#ifdef IPG_DEBUG
-static void ipg_dump_rfdlist(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
- u32 offset;
-
- IPG_DEBUG_MSG("_dump_rfdlist\n");
-
- netdev_info(dev, "rx_current = %02x\n", sp->rx_current);
- netdev_info(dev, "rx_dirty = %02x\n", sp->rx_dirty);
- netdev_info(dev, "RFDList start address = %016lx\n",
- (unsigned long)sp->rxd_map);
- netdev_info(dev, "RFDListPtr register = %08x%08x\n",
- ipg_r32(IPG_RFDLISTPTR1), ipg_r32(IPG_RFDLISTPTR0));
-
- for (i = 0; i < IPG_RFDLIST_LENGTH; i++) {
- offset = (u32) &sp->rxd[i].next_desc - (u32) sp->rxd;
- netdev_info(dev, "%02x %04x RFDNextPtr = %016lx\n",
- i, offset, (unsigned long)sp->rxd[i].next_desc);
- offset = (u32) &sp->rxd[i].rfs - (u32) sp->rxd;
- netdev_info(dev, "%02x %04x RFS = %016lx\n",
- i, offset, (unsigned long)sp->rxd[i].rfs);
- offset = (u32) &sp->rxd[i].frag_info - (u32) sp->rxd;
- netdev_info(dev, "%02x %04x frag_info = %016lx\n",
- i, offset, (unsigned long)sp->rxd[i].frag_info);
- }
-}
-
-static void ipg_dump_tfdlist(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
- u32 offset;
-
- IPG_DEBUG_MSG("_dump_tfdlist\n");
-
- netdev_info(dev, "tx_current = %02x\n", sp->tx_current);
- netdev_info(dev, "tx_dirty = %02x\n", sp->tx_dirty);
- netdev_info(dev, "TFDList start address = %016lx\n",
- (unsigned long) sp->txd_map);
- netdev_info(dev, "TFDListPtr register = %08x%08x\n",
- ipg_r32(IPG_TFDLISTPTR1), ipg_r32(IPG_TFDLISTPTR0));
-
- for (i = 0; i < IPG_TFDLIST_LENGTH; i++) {
- offset = (u32) &sp->txd[i].next_desc - (u32) sp->txd;
- netdev_info(dev, "%02x %04x TFDNextPtr = %016lx\n",
- i, offset, (unsigned long)sp->txd[i].next_desc);
-
- offset = (u32) &sp->txd[i].tfc - (u32) sp->txd;
- netdev_info(dev, "%02x %04x TFC = %016lx\n",
- i, offset, (unsigned long) sp->txd[i].tfc);
- offset = (u32) &sp->txd[i].frag_info - (u32) sp->txd;
- netdev_info(dev, "%02x %04x frag_info = %016lx\n",
- i, offset, (unsigned long) sp->txd[i].frag_info);
- }
-}
-#endif
-
-static void ipg_write_phy_ctl(void __iomem *ioaddr, u8 data)
-{
- ipg_w8(IPG_PC_RSVD_MASK & data, PHY_CTRL);
- ndelay(IPG_PC_PHYCTRLWAIT_NS);
-}
-
-static void ipg_drive_phy_ctl_low_high(void __iomem *ioaddr, u8 data)
-{
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_LO | data);
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_HI | data);
-}
-
-static void send_three_state(void __iomem *ioaddr, u8 phyctrlpolarity)
-{
- phyctrlpolarity |= (IPG_PC_MGMTDATA & 0) | IPG_PC_MGMTDIR;
-
- ipg_drive_phy_ctl_low_high(ioaddr, phyctrlpolarity);
-}
-
-static void send_end(void __iomem *ioaddr, u8 phyctrlpolarity)
-{
- ipg_w8((IPG_PC_MGMTCLK_LO | (IPG_PC_MGMTDATA & 0) | IPG_PC_MGMTDIR |
- phyctrlpolarity) & IPG_PC_RSVD_MASK, PHY_CTRL);
-}
-
-static u16 read_phy_bit(void __iomem *ioaddr, u8 phyctrlpolarity)
-{
- u16 bit_data;
-
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_LO | phyctrlpolarity);
-
- bit_data = ((ipg_r8(PHY_CTRL) & IPG_PC_MGMTDATA) >> 1) & 1;
-
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_HI | phyctrlpolarity);
-
- return bit_data;
-}
-
-/*
- * Read a register from the Physical Layer device located
- * on the IPG NIC, using the IPG PHYCTRL register.
- */
-static int mdio_read(struct net_device *dev, int phy_id, int phy_reg)
-{
- void __iomem *ioaddr = ipg_ioaddr(dev);
- /*
- * The GMII mangement frame structure for a read is as follows:
- *
- * |Preamble|st|op|phyad|regad|ta| data |idle|
- * |< 32 1s>|01|10|AAAAA|RRRRR|z0|DDDDDDDDDDDDDDDD|z |
- *
- * <32 1s> = 32 consecutive logic 1 values
- * A = bit of Physical Layer device address (MSB first)
- * R = bit of register address (MSB first)
- * z = High impedance state
- * D = bit of read data (MSB first)
- *
- * Transmission order is 'Preamble' field first, bits transmitted
- * left to right (first to last).
- */
- struct {
- u32 field;
- unsigned int len;
- } p[] = {
- { GMII_PREAMBLE, 32 }, /* Preamble */
- { GMII_ST, 2 }, /* ST */
- { GMII_READ, 2 }, /* OP */
- { phy_id, 5 }, /* PHYAD */
- { phy_reg, 5 }, /* REGAD */
- { 0x0000, 2 }, /* TA */
- { 0x0000, 16 }, /* DATA */
- { 0x0000, 1 } /* IDLE */
- };
- unsigned int i, j;
- u8 polarity, data;
-
- polarity = ipg_r8(PHY_CTRL);
- polarity &= (IPG_PC_DUPLEX_POLARITY | IPG_PC_LINK_POLARITY);
-
- /* Create the Preamble, ST, OP, PHYAD, and REGAD field. */
- for (j = 0; j < 5; j++) {
- for (i = 0; i < p[j].len; i++) {
- /* For each variable length field, the MSB must be
- * transmitted first. Rotate through the field bits,
- * starting with the MSB, and move each bit into the
- * the 1st (2^1) bit position (this is the bit position
- * corresponding to the MgmtData bit of the PhyCtrl
- * register for the IPG).
- *
- * Example: ST = 01;
- *
- * First write a '0' to bit 1 of the PhyCtrl
- * register, then write a '1' to bit 1 of the
- * PhyCtrl register.
- *
- * To do this, right shift the MSB of ST by the value:
- * [field length - 1 - #ST bits already written]
- * then left shift this result by 1.
- */
- data = (p[j].field >> (p[j].len - 1 - i)) << 1;
- data &= IPG_PC_MGMTDATA;
- data |= polarity | IPG_PC_MGMTDIR;
-
- ipg_drive_phy_ctl_low_high(ioaddr, data);
- }
- }
-
- send_three_state(ioaddr, polarity);
-
- read_phy_bit(ioaddr, polarity);
-
- /*
- * For a read cycle, the bits for the next two fields (TA and
- * DATA) are driven by the PHY (the IPG reads these bits).
- */
- for (i = 0; i < p[6].len; i++) {
- p[6].field |=
- (read_phy_bit(ioaddr, polarity) << (p[6].len - 1 - i));
- }
-
- send_three_state(ioaddr, polarity);
- send_three_state(ioaddr, polarity);
- send_three_state(ioaddr, polarity);
- send_end(ioaddr, polarity);
-
- /* Return the value of the DATA field. */
- return p[6].field;
-}
-
-/*
- * Write to a register from the Physical Layer device located
- * on the IPG NIC, using the IPG PHYCTRL register.
- */
-static void mdio_write(struct net_device *dev, int phy_id, int phy_reg, int val)
-{
- void __iomem *ioaddr = ipg_ioaddr(dev);
- /*
- * The GMII mangement frame structure for a read is as follows:
- *
- * |Preamble|st|op|phyad|regad|ta| data |idle|
- * |< 32 1s>|01|10|AAAAA|RRRRR|z0|DDDDDDDDDDDDDDDD|z |
- *
- * <32 1s> = 32 consecutive logic 1 values
- * A = bit of Physical Layer device address (MSB first)
- * R = bit of register address (MSB first)
- * z = High impedance state
- * D = bit of write data (MSB first)
- *
- * Transmission order is 'Preamble' field first, bits transmitted
- * left to right (first to last).
- */
- struct {
- u32 field;
- unsigned int len;
- } p[] = {
- { GMII_PREAMBLE, 32 }, /* Preamble */
- { GMII_ST, 2 }, /* ST */
- { GMII_WRITE, 2 }, /* OP */
- { phy_id, 5 }, /* PHYAD */
- { phy_reg, 5 }, /* REGAD */
- { 0x0002, 2 }, /* TA */
- { val & 0xffff, 16 }, /* DATA */
- { 0x0000, 1 } /* IDLE */
- };
- unsigned int i, j;
- u8 polarity, data;
-
- polarity = ipg_r8(PHY_CTRL);
- polarity &= (IPG_PC_DUPLEX_POLARITY | IPG_PC_LINK_POLARITY);
-
- /* Create the Preamble, ST, OP, PHYAD, and REGAD field. */
- for (j = 0; j < 7; j++) {
- for (i = 0; i < p[j].len; i++) {
- /* For each variable length field, the MSB must be
- * transmitted first. Rotate through the field bits,
- * starting with the MSB, and move each bit into the
- * the 1st (2^1) bit position (this is the bit position
- * corresponding to the MgmtData bit of the PhyCtrl
- * register for the IPG).
- *
- * Example: ST = 01;
- *
- * First write a '0' to bit 1 of the PhyCtrl
- * register, then write a '1' to bit 1 of the
- * PhyCtrl register.
- *
- * To do this, right shift the MSB of ST by the value:
- * [field length - 1 - #ST bits already written]
- * then left shift this result by 1.
- */
- data = (p[j].field >> (p[j].len - 1 - i)) << 1;
- data &= IPG_PC_MGMTDATA;
- data |= polarity | IPG_PC_MGMTDIR;
-
- ipg_drive_phy_ctl_low_high(ioaddr, data);
- }
- }
-
- /* The last cycle is a tri-state, so read from the PHY. */
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_LO | polarity);
- ipg_r8(PHY_CTRL);
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_HI | polarity);
-}
-
-static void ipg_set_led_mode(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- u32 mode;
-
- mode = ipg_r32(ASIC_CTRL);
- mode &= ~(IPG_AC_LED_MODE_BIT_1 | IPG_AC_LED_MODE | IPG_AC_LED_SPEED);
-
- if ((sp->led_mode & 0x03) > 1)
- mode |= IPG_AC_LED_MODE_BIT_1; /* Write Asic Control Bit 29 */
-
- if ((sp->led_mode & 0x01) == 1)
- mode |= IPG_AC_LED_MODE; /* Write Asic Control Bit 14 */
-
- if ((sp->led_mode & 0x08) == 8)
- mode |= IPG_AC_LED_SPEED; /* Write Asic Control Bit 27 */
-
- ipg_w32(mode, ASIC_CTRL);
-}
-
-static void ipg_set_phy_set(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- int physet;
-
- physet = ipg_r8(PHY_SET);
- physet &= ~(IPG_PS_MEM_LENB9B | IPG_PS_MEM_LEN9 | IPG_PS_NON_COMPDET);
- physet |= ((sp->led_mode & 0x70) >> 4);
- ipg_w8(physet, PHY_SET);
-}
-
-static int ipg_reset(struct net_device *dev, u32 resetflags)
-{
- /* Assert functional resets via the IPG AsicCtrl
- * register as specified by the 'resetflags' input
- * parameter.
- */
- void __iomem *ioaddr = ipg_ioaddr(dev);
- unsigned int timeout_count = 0;
-
- IPG_DEBUG_MSG("_reset\n");
-
- ipg_w32(ipg_r32(ASIC_CTRL) | resetflags, ASIC_CTRL);
-
- /* Delay added to account for problem with 10Mbps reset. */
- mdelay(IPG_AC_RESETWAIT);
-
- while (IPG_AC_RESET_BUSY & ipg_r32(ASIC_CTRL)) {
- mdelay(IPG_AC_RESETWAIT);
- if (++timeout_count > IPG_AC_RESET_TIMEOUT)
- return -ETIME;
- }
- /* Set LED Mode in Asic Control */
- ipg_set_led_mode(dev);
-
- /* Set PHYSet Register Value */
- ipg_set_phy_set(dev);
- return 0;
-}
-
-/* Find the GMII PHY address. */
-static int ipg_find_phyaddr(struct net_device *dev)
-{
- unsigned int phyaddr, i;
-
- for (i = 0; i < 32; i++) {
- u32 status;
-
- /* Search for the correct PHY address among 32 possible. */
- phyaddr = (IPG_NIC_PHY_ADDRESS + i) % 32;
-
- /* 10/22/03 Grace change verify from GMII_PHY_STATUS to
- GMII_PHY_ID1
- */
-
- status = mdio_read(dev, phyaddr, MII_BMSR);
-
- if ((status != 0xFFFF) && (status != 0))
- return phyaddr;
- }
-
- return 0x1f;
-}
-
-/*
- * Configure IPG based on result of IEEE 802.3 PHY
- * auto-negotiation.
- */
-static int ipg_config_autoneg(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int txflowcontrol;
- unsigned int rxflowcontrol;
- unsigned int fullduplex;
- u32 mac_ctrl_val;
- u32 asicctrl;
- u8 phyctrl;
- const char *speed;
- const char *duplex;
- const char *tx_desc;
- const char *rx_desc;
-
- IPG_DEBUG_MSG("_config_autoneg\n");
-
- asicctrl = ipg_r32(ASIC_CTRL);
- phyctrl = ipg_r8(PHY_CTRL);
- mac_ctrl_val = ipg_r32(MAC_CTRL);
-
- /* Set flags for use in resolving auto-negotiation, assuming
- * non-1000Mbps, half duplex, no flow control.
- */
- fullduplex = 0;
- txflowcontrol = 0;
- rxflowcontrol = 0;
-
- /* To accommodate a problem in 10Mbps operation,
- * set a global flag if PHY running in 10Mbps mode.
- */
- sp->tenmbpsmode = 0;
-
- /* Determine actual speed of operation. */
- switch (phyctrl & IPG_PC_LINK_SPEED) {
- case IPG_PC_LINK_SPEED_10MBPS:
- speed = "10Mbps";
- sp->tenmbpsmode = 1;
- break;
- case IPG_PC_LINK_SPEED_100MBPS:
- speed = "100Mbps";
- break;
- case IPG_PC_LINK_SPEED_1000MBPS:
- speed = "1000Mbps";
- break;
- default:
- speed = "undefined!";
- return 0;
- }
-
- netdev_info(dev, "Link speed = %s\n", speed);
- if (sp->tenmbpsmode == 1)
- netdev_info(dev, "10Mbps operational mode enabled\n");
-
- if (phyctrl & IPG_PC_DUPLEX_STATUS) {
- fullduplex = 1;
- txflowcontrol = 1;
- rxflowcontrol = 1;
- }
-
- /* Configure full duplex, and flow control. */
- if (fullduplex == 1) {
-
- /* Configure IPG for full duplex operation. */
-
- duplex = "full";
-
- mac_ctrl_val |= IPG_MC_DUPLEX_SELECT_FD;
-
- if (txflowcontrol == 1) {
- tx_desc = "";
- mac_ctrl_val |= IPG_MC_TX_FLOW_CONTROL_ENABLE;
- } else {
- tx_desc = "no ";
- mac_ctrl_val &= ~IPG_MC_TX_FLOW_CONTROL_ENABLE;
- }
-
- if (rxflowcontrol == 1) {
- rx_desc = "";
- mac_ctrl_val |= IPG_MC_RX_FLOW_CONTROL_ENABLE;
- } else {
- rx_desc = "no ";
- mac_ctrl_val &= ~IPG_MC_RX_FLOW_CONTROL_ENABLE;
- }
- } else {
- duplex = "half";
- tx_desc = "no ";
- rx_desc = "no ";
- mac_ctrl_val &= (~IPG_MC_DUPLEX_SELECT_FD &
- ~IPG_MC_TX_FLOW_CONTROL_ENABLE &
- ~IPG_MC_RX_FLOW_CONTROL_ENABLE);
- }
-
- netdev_info(dev, "setting %s duplex, %sTX, %sRX flow control\n",
- duplex, tx_desc, rx_desc);
- ipg_w32(mac_ctrl_val, MAC_CTRL);
-
- return 0;
-}
-
-/* Determine and configure multicast operation and set
- * receive mode for IPG.
- */
-static void ipg_nic_set_multicast_list(struct net_device *dev)
-{
- void __iomem *ioaddr = ipg_ioaddr(dev);
- struct netdev_hw_addr *ha;
- unsigned int hashindex;
- u32 hashtable[2];
- u8 receivemode;
-
- IPG_DEBUG_MSG("_nic_set_multicast_list\n");
-
- receivemode = IPG_RM_RECEIVEUNICAST | IPG_RM_RECEIVEBROADCAST;
-
- if (dev->flags & IFF_PROMISC) {
- /* NIC to be configured in promiscuous mode. */
- receivemode = IPG_RM_RECEIVEALLFRAMES;
- } else if ((dev->flags & IFF_ALLMULTI) ||
- ((dev->flags & IFF_MULTICAST) &&
- (netdev_mc_count(dev) > IPG_MULTICAST_HASHTABLE_SIZE))) {
- /* NIC to be configured to receive all multicast
- * frames. */
- receivemode |= IPG_RM_RECEIVEMULTICAST;
- } else if ((dev->flags & IFF_MULTICAST) && !netdev_mc_empty(dev)) {
- /* NIC to be configured to receive selected
- * multicast addresses. */
- receivemode |= IPG_RM_RECEIVEMULTICASTHASH;
- }
-
- /* Calculate the bits to set for the 64 bit, IPG HASHTABLE.
- * The IPG applies a cyclic-redundancy-check (the same CRC
- * used to calculate the frame data FCS) to the destination
- * address all incoming multicast frames whose destination
- * address has the multicast bit set. The least significant
- * 6 bits of the CRC result are used as an addressing index
- * into the hash table. If the value of the bit addressed by
- * this index is a 1, the frame is passed to the host system.
- */
-
- /* Clear hashtable. */
- hashtable[0] = 0x00000000;
- hashtable[1] = 0x00000000;
-
- /* Cycle through all multicast addresses to filter. */
- netdev_for_each_mc_addr(ha, dev) {
- /* Calculate CRC result for each multicast address. */
- hashindex = crc32_le(0xffffffff, ha->addr,
- ETH_ALEN);
-
- /* Use only the least significant 6 bits. */
- hashindex = hashindex & 0x3F;
-
- /* Within "hashtable", set bit number "hashindex"
- * to a logic 1.
- */
- set_bit(hashindex, (void *)hashtable);
- }
-
- /* Write the value of the hashtable, to the 4, 16 bit
- * HASHTABLE IPG registers.
- */
- ipg_w32(hashtable[0], HASHTABLE_0);
- ipg_w32(hashtable[1], HASHTABLE_1);
-
- ipg_w8(IPG_RM_RSVD_MASK & receivemode, RECEIVE_MODE);
-
- IPG_DEBUG_MSG("ReceiveMode = %x\n", ipg_r8(RECEIVE_MODE));
-}
-
-static int ipg_io_config(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = ipg_ioaddr(dev);
- u32 origmacctrl;
- u32 restoremacctrl;
-
- IPG_DEBUG_MSG("_io_config\n");
-
- origmacctrl = ipg_r32(MAC_CTRL);
-
- restoremacctrl = origmacctrl | IPG_MC_STATISTICS_ENABLE;
-
- /* Based on compilation option, determine if FCS is to be
- * stripped on receive frames by IPG.
- */
- if (!IPG_STRIP_FCS_ON_RX)
- restoremacctrl |= IPG_MC_RCV_FCS;
-
- /* Determine if transmitter and/or receiver are
- * enabled so we may restore MACCTRL correctly.
- */
- if (origmacctrl & IPG_MC_TX_ENABLED)
- restoremacctrl |= IPG_MC_TX_ENABLE;
-
- if (origmacctrl & IPG_MC_RX_ENABLED)
- restoremacctrl |= IPG_MC_RX_ENABLE;
-
- /* Transmitter and receiver must be disabled before setting
- * IFSSelect.
- */
- ipg_w32((origmacctrl & (IPG_MC_RX_DISABLE | IPG_MC_TX_DISABLE)) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
-
- /* Now that transmitter and receiver are disabled, write
- * to IFSSelect.
- */
- ipg_w32((origmacctrl & IPG_MC_IFS_96BIT) & IPG_MC_RSVD_MASK, MAC_CTRL);
-
- /* Set RECEIVEMODE register. */
- ipg_nic_set_multicast_list(dev);
-
- ipg_w16(sp->max_rxframe_size, MAX_FRAME_SIZE);
-
- ipg_w8(IPG_RXDMAPOLLPERIOD_VALUE, RX_DMA_POLL_PERIOD);
- ipg_w8(IPG_RXDMAURGENTTHRESH_VALUE, RX_DMA_URGENT_THRESH);
- ipg_w8(IPG_RXDMABURSTTHRESH_VALUE, RX_DMA_BURST_THRESH);
- ipg_w8(IPG_TXDMAPOLLPERIOD_VALUE, TX_DMA_POLL_PERIOD);
- ipg_w8(IPG_TXDMAURGENTTHRESH_VALUE, TX_DMA_URGENT_THRESH);
- ipg_w8(IPG_TXDMABURSTTHRESH_VALUE, TX_DMA_BURST_THRESH);
- ipg_w16((IPG_IE_HOST_ERROR | IPG_IE_TX_DMA_COMPLETE |
- IPG_IE_TX_COMPLETE | IPG_IE_INT_REQUESTED |
- IPG_IE_UPDATE_STATS | IPG_IE_LINK_EVENT |
- IPG_IE_RX_DMA_COMPLETE | IPG_IE_RX_DMA_PRIORITY), INT_ENABLE);
- ipg_w16(IPG_FLOWONTHRESH_VALUE, FLOW_ON_THRESH);
- ipg_w16(IPG_FLOWOFFTHRESH_VALUE, FLOW_OFF_THRESH);
-
- /* IPG multi-frag frame bug workaround.
- * Per silicon revision B3 eratta.
- */
- ipg_w16(ipg_r16(DEBUG_CTRL) | 0x0200, DEBUG_CTRL);
-
- /* IPG TX poll now bug workaround.
- * Per silicon revision B3 eratta.
- */
- ipg_w16(ipg_r16(DEBUG_CTRL) | 0x0010, DEBUG_CTRL);
-
- /* IPG RX poll now bug workaround.
- * Per silicon revision B3 eratta.
- */
- ipg_w16(ipg_r16(DEBUG_CTRL) | 0x0020, DEBUG_CTRL);
-
- /* Now restore MACCTRL to original setting. */
- ipg_w32(IPG_MC_RSVD_MASK & restoremacctrl, MAC_CTRL);
-
- /* Disable unused RMON statistics. */
- ipg_w32(IPG_RZ_ALL, RMON_STATISTICS_MASK);
-
- /* Disable unused MIB statistics. */
- ipg_w32(IPG_SM_MACCONTROLFRAMESXMTD | IPG_SM_MACCONTROLFRAMESRCVD |
- IPG_SM_BCSTOCTETXMTOK_BCSTFRAMESXMTDOK | IPG_SM_TXJUMBOFRAMES |
- IPG_SM_MCSTOCTETXMTOK_MCSTFRAMESXMTDOK | IPG_SM_RXJUMBOFRAMES |
- IPG_SM_BCSTOCTETRCVDOK_BCSTFRAMESRCVDOK |
- IPG_SM_UDPCHECKSUMERRORS | IPG_SM_TCPCHECKSUMERRORS |
- IPG_SM_IPCHECKSUMERRORS, STATISTICS_MASK);
-
- return 0;
-}
-
-/*
- * Create a receive buffer within system memory and update
- * NIC private structure appropriately.
- */
-static int ipg_get_rxbuff(struct net_device *dev, int entry)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- struct ipg_rx *rxfd = sp->rxd + entry;
- struct sk_buff *skb;
- u64 rxfragsize;
-
- IPG_DEBUG_MSG("_get_rxbuff\n");
-
- skb = netdev_alloc_skb_ip_align(dev, sp->rxsupport_size);
- if (!skb) {
- sp->rx_buff[entry] = NULL;
- return -ENOMEM;
- }
-
- /* Save the address of the sk_buff structure. */
- sp->rx_buff[entry] = skb;
-
- rxfd->frag_info = cpu_to_le64(pci_map_single(sp->pdev, skb->data,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE));
-
- /* Set the RFD fragment length. */
- rxfragsize = sp->rxfrag_size;
- rxfd->frag_info |= cpu_to_le64((rxfragsize << 48) & IPG_RFI_FRAGLEN);
-
- return 0;
-}
-
-static int init_rfdlist(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
-
- IPG_DEBUG_MSG("_init_rfdlist\n");
-
- for (i = 0; i < IPG_RFDLIST_LENGTH; i++) {
- struct ipg_rx *rxfd = sp->rxd + i;
-
- if (sp->rx_buff[i]) {
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
- dev_kfree_skb_irq(sp->rx_buff[i]);
- sp->rx_buff[i] = NULL;
- }
-
- /* Clear out the RFS field. */
- rxfd->rfs = 0x0000000000000000;
-
- if (ipg_get_rxbuff(dev, i) < 0) {
- /*
- * A receive buffer was not ready, break the
- * RFD list here.
- */
- IPG_DEBUG_MSG("Cannot allocate Rx buffer\n");
-
- /* Just in case we cannot allocate a single RFD.
- * Should not occur.
- */
- if (i == 0) {
- netdev_err(dev, "No memory available for RFD list\n");
- return -ENOMEM;
- }
- }
-
- rxfd->next_desc = cpu_to_le64(sp->rxd_map +
- sizeof(struct ipg_rx)*(i + 1));
- }
- sp->rxd[i - 1].next_desc = cpu_to_le64(sp->rxd_map);
-
- sp->rx_current = 0;
- sp->rx_dirty = 0;
-
- /* Write the location of the RFDList to the IPG. */
- ipg_w32((u32) sp->rxd_map, RFD_LIST_PTR_0);
- ipg_w32(0x00000000, RFD_LIST_PTR_1);
-
- return 0;
-}
-
-static void init_tfdlist(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
-
- IPG_DEBUG_MSG("_init_tfdlist\n");
-
- for (i = 0; i < IPG_TFDLIST_LENGTH; i++) {
- struct ipg_tx *txfd = sp->txd + i;
-
- txfd->tfc = cpu_to_le64(IPG_TFC_TFDDONE);
-
- if (sp->tx_buff[i]) {
- dev_kfree_skb_irq(sp->tx_buff[i]);
- sp->tx_buff[i] = NULL;
- }
-
- txfd->next_desc = cpu_to_le64(sp->txd_map +
- sizeof(struct ipg_tx)*(i + 1));
- }
- sp->txd[i - 1].next_desc = cpu_to_le64(sp->txd_map);
-
- sp->tx_current = 0;
- sp->tx_dirty = 0;
-
- /* Write the location of the TFDList to the IPG. */
- IPG_DDEBUG_MSG("Starting TFDListPtr = %08x\n",
- (u32) sp->txd_map);
- ipg_w32((u32) sp->txd_map, TFD_LIST_PTR_0);
- ipg_w32(0x00000000, TFD_LIST_PTR_1);
-
- sp->reset_current_tfd = 1;
-}
-
-/*
- * Free all transmit buffers which have already been transferred
- * via DMA to the IPG.
- */
-static void ipg_nic_txfree(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int released, pending, dirty;
-
- IPG_DEBUG_MSG("_nic_txfree\n");
-
- pending = sp->tx_current - sp->tx_dirty;
- dirty = sp->tx_dirty % IPG_TFDLIST_LENGTH;
-
- for (released = 0; released < pending; released++) {
- struct sk_buff *skb = sp->tx_buff[dirty];
- struct ipg_tx *txfd = sp->txd + dirty;
-
- IPG_DEBUG_MSG("TFC = %016lx\n", (unsigned long) txfd->tfc);
-
- /* Look at each TFD's TFC field beginning
- * at the last freed TFD up to the current TFD.
- * If the TFDDone bit is set, free the associated
- * buffer.
- */
- if (!(txfd->tfc & cpu_to_le64(IPG_TFC_TFDDONE)))
- break;
-
- /* Free the transmit buffer. */
- if (skb) {
- pci_unmap_single(sp->pdev,
- le64_to_cpu(txfd->frag_info) & ~IPG_TFI_FRAGLEN,
- skb->len, PCI_DMA_TODEVICE);
-
- dev_kfree_skb_irq(skb);
-
- sp->tx_buff[dirty] = NULL;
- }
- dirty = (dirty + 1) % IPG_TFDLIST_LENGTH;
- }
-
- sp->tx_dirty += released;
-
- if (netif_queue_stopped(dev) &&
- (sp->tx_current != (sp->tx_dirty + IPG_TFDLIST_LENGTH))) {
- netif_wake_queue(dev);
- }
-}
-
-static void ipg_tx_timeout(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
-
- ipg_reset(dev, IPG_AC_TX_RESET | IPG_AC_DMA | IPG_AC_NETWORK |
- IPG_AC_FIFO);
-
- spin_lock_irq(&sp->lock);
-
- /* Re-configure after DMA reset. */
- if (ipg_io_config(dev) < 0)
- netdev_info(dev, "Error during re-configuration\n");
-
- init_tfdlist(dev);
-
- spin_unlock_irq(&sp->lock);
-
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_TX_ENABLE) & IPG_MC_RSVD_MASK,
- MAC_CTRL);
-}
-
-/*
- * For TxComplete interrupts, free all transmit
- * buffers which have already been transferred via DMA
- * to the IPG.
- */
-static void ipg_nic_txcleanup(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
-
- IPG_DEBUG_MSG("_nic_txcleanup\n");
-
- for (i = 0; i < IPG_TFDLIST_LENGTH; i++) {
- /* Reading the TXSTATUS register clears the
- * TX_COMPLETE interrupt.
- */
- u32 txstatusdword = ipg_r32(TX_STATUS);
-
- IPG_DEBUG_MSG("TxStatus = %08x\n", txstatusdword);
-
- /* Check for Transmit errors. Error bits only valid if
- * TX_COMPLETE bit in the TXSTATUS register is a 1.
- */
- if (!(txstatusdword & IPG_TS_TX_COMPLETE))
- break;
-
- /* If in 10Mbps mode, indicate transmit is ready. */
- if (sp->tenmbpsmode) {
- netif_wake_queue(dev);
- }
-
- /* Transmit error, increment stat counters. */
- if (txstatusdword & IPG_TS_TX_ERROR) {
- IPG_DEBUG_MSG("Transmit error\n");
- sp->stats.tx_errors++;
- }
-
- /* Late collision, re-enable transmitter. */
- if (txstatusdword & IPG_TS_LATE_COLLISION) {
- IPG_DEBUG_MSG("Late collision on transmit\n");
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_TX_ENABLE) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
- }
-
- /* Maximum collisions, re-enable transmitter. */
- if (txstatusdword & IPG_TS_TX_MAX_COLL) {
- IPG_DEBUG_MSG("Maximum collisions on transmit\n");
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_TX_ENABLE) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
- }
-
- /* Transmit underrun, reset and re-enable
- * transmitter.
- */
- if (txstatusdword & IPG_TS_TX_UNDERRUN) {
- IPG_DEBUG_MSG("Transmitter underrun\n");
- sp->stats.tx_fifo_errors++;
- ipg_reset(dev, IPG_AC_TX_RESET | IPG_AC_DMA |
- IPG_AC_NETWORK | IPG_AC_FIFO);
-
- /* Re-configure after DMA reset. */
- if (ipg_io_config(dev) < 0) {
- netdev_info(dev, "Error during re-configuration\n");
- }
- init_tfdlist(dev);
-
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_TX_ENABLE) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
- }
- }
-
- ipg_nic_txfree(dev);
-}
-
-/* Provides statistical information about the IPG NIC. */
-static struct net_device_stats *ipg_nic_get_stats(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- u16 temp1;
- u16 temp2;
-
- IPG_DEBUG_MSG("_nic_get_stats\n");
-
- /* Check to see if the NIC has been initialized via nic_open,
- * before trying to read statistic registers.
- */
- if (!netif_running(dev))
- return &sp->stats;
-
- sp->stats.rx_packets += ipg_r32(IPG_FRAMESRCVDOK);
- sp->stats.tx_packets += ipg_r32(IPG_FRAMESXMTDOK);
- sp->stats.rx_bytes += ipg_r32(IPG_OCTETRCVOK);
- sp->stats.tx_bytes += ipg_r32(IPG_OCTETXMTOK);
- temp1 = ipg_r16(IPG_FRAMESLOSTRXERRORS);
- sp->stats.rx_errors += temp1;
- sp->stats.rx_missed_errors += temp1;
- temp1 = ipg_r32(IPG_SINGLECOLFRAMES) + ipg_r32(IPG_MULTICOLFRAMES) +
- ipg_r32(IPG_LATECOLLISIONS);
- temp2 = ipg_r16(IPG_CARRIERSENSEERRORS);
- sp->stats.collisions += temp1;
- sp->stats.tx_dropped += ipg_r16(IPG_FRAMESABORTXSCOLLS);
- sp->stats.tx_errors += ipg_r16(IPG_FRAMESWEXDEFERRAL) +
- ipg_r32(IPG_FRAMESWDEFERREDXMT) + temp1 + temp2;
- sp->stats.multicast += ipg_r32(IPG_MCSTOCTETRCVDOK);
-
- /* detailed tx_errors */
- sp->stats.tx_carrier_errors += temp2;
-
- /* detailed rx_errors */
- sp->stats.rx_length_errors += ipg_r16(IPG_INRANGELENGTHERRORS) +
- ipg_r16(IPG_FRAMETOOLONGERRORS);
- sp->stats.rx_crc_errors += ipg_r16(IPG_FRAMECHECKSEQERRORS);
-
- /* Unutilized IPG statistic registers. */
- ipg_r32(IPG_MCSTFRAMESRCVDOK);
-
- return &sp->stats;
-}
-
-/* Restore used receive buffers. */
-static int ipg_nic_rxrestore(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- const unsigned int curr = sp->rx_current;
- unsigned int dirty = sp->rx_dirty;
-
- IPG_DEBUG_MSG("_nic_rxrestore\n");
-
- for (dirty = sp->rx_dirty; curr - dirty > 0; dirty++) {
- unsigned int entry = dirty % IPG_RFDLIST_LENGTH;
-
- /* rx_copybreak may poke hole here and there. */
- if (sp->rx_buff[entry])
- continue;
-
- /* Generate a new receive buffer to replace the
- * current buffer (which will be released by the
- * Linux system).
- */
- if (ipg_get_rxbuff(dev, entry) < 0) {
- IPG_DEBUG_MSG("Cannot allocate new Rx buffer\n");
-
- break;
- }
-
- /* Reset the RFS field. */
- sp->rxd[entry].rfs = 0x0000000000000000;
- }
- sp->rx_dirty = dirty;
-
- return 0;
-}
-
-/* use jumboindex and jumbosize to control jumbo frame status
- * initial status is jumboindex=-1 and jumbosize=0
- * 1. jumboindex = -1 and jumbosize=0 : previous jumbo frame has been done.
- * 2. jumboindex != -1 and jumbosize != 0 : jumbo frame is not over size and receiving
- * 3. jumboindex = -1 and jumbosize != 0 : jumbo frame is over size, already dump
- * previous receiving and need to continue dumping the current one
- */
-enum {
- NORMAL_PACKET,
- ERROR_PACKET
-};
-
-enum {
- FRAME_NO_START_NO_END = 0,
- FRAME_WITH_START = 1,
- FRAME_WITH_END = 10,
- FRAME_WITH_START_WITH_END = 11
-};
-
-static void ipg_nic_rx_free_skb(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int entry = sp->rx_current % IPG_RFDLIST_LENGTH;
-
- if (sp->rx_buff[entry]) {
- struct ipg_rx *rxfd = sp->rxd + entry;
-
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
- dev_kfree_skb_irq(sp->rx_buff[entry]);
- sp->rx_buff[entry] = NULL;
- }
-}
-
-static int ipg_nic_rx_check_frame_type(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- struct ipg_rx *rxfd = sp->rxd + (sp->rx_current % IPG_RFDLIST_LENGTH);
- int type = FRAME_NO_START_NO_END;
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_FRAMESTART)
- type += FRAME_WITH_START;
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_FRAMEEND)
- type += FRAME_WITH_END;
- return type;
-}
-
-static int ipg_nic_rx_check_error(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int entry = sp->rx_current % IPG_RFDLIST_LENGTH;
- struct ipg_rx *rxfd = sp->rxd + entry;
-
- if (IPG_DROP_ON_RX_ETH_ERRORS && (le64_to_cpu(rxfd->rfs) &
- (IPG_RFS_RXFIFOOVERRUN | IPG_RFS_RXRUNTFRAME |
- IPG_RFS_RXALIGNMENTERROR | IPG_RFS_RXFCSERROR |
- IPG_RFS_RXOVERSIZEDFRAME | IPG_RFS_RXLENGTHERROR))) {
- IPG_DEBUG_MSG("Rx error, RFS = %016lx\n",
- (unsigned long) rxfd->rfs);
-
- /* Increment general receive error statistic. */
- sp->stats.rx_errors++;
-
- /* Increment detailed receive error statistics. */
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFIFOOVERRUN) {
- IPG_DEBUG_MSG("RX FIFO overrun occurred\n");
-
- sp->stats.rx_fifo_errors++;
- }
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXRUNTFRAME) {
- IPG_DEBUG_MSG("RX runt occurred\n");
- sp->stats.rx_length_errors++;
- }
-
- /* Do nothing for IPG_RFS_RXOVERSIZEDFRAME,
- * error count handled by a IPG statistic register.
- */
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXALIGNMENTERROR) {
- IPG_DEBUG_MSG("RX alignment error occurred\n");
- sp->stats.rx_frame_errors++;
- }
-
- /* Do nothing for IPG_RFS_RXFCSERROR, error count
- * handled by a IPG statistic register.
- */
-
- /* Free the memory associated with the RX
- * buffer since it is erroneous and we will
- * not pass it to higher layer processes.
- */
- if (sp->rx_buff[entry]) {
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
-
- dev_kfree_skb_irq(sp->rx_buff[entry]);
- sp->rx_buff[entry] = NULL;
- }
- return ERROR_PACKET;
- }
- return NORMAL_PACKET;
-}
-
-static void ipg_nic_rx_with_start_and_end(struct net_device *dev,
- struct ipg_nic_private *sp,
- struct ipg_rx *rxfd, unsigned entry)
-{
- struct ipg_jumbo *jumbo = &sp->jumbo;
- struct sk_buff *skb;
- int framelen;
-
- if (jumbo->found_start) {
- dev_kfree_skb_irq(jumbo->skb);
- jumbo->found_start = 0;
- jumbo->current_size = 0;
- jumbo->skb = NULL;
- }
-
- /* 1: found error, 0 no error */
- if (ipg_nic_rx_check_error(dev) != NORMAL_PACKET)
- return;
-
- skb = sp->rx_buff[entry];
- if (!skb)
- return;
-
- /* accept this frame and send to upper layer */
- framelen = le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFRAMELEN;
- if (framelen > sp->rxfrag_size)
- framelen = sp->rxfrag_size;
-
- skb_put(skb, framelen);
- skb->protocol = eth_type_trans(skb, dev);
- skb_checksum_none_assert(skb);
- netif_rx(skb);
- sp->rx_buff[entry] = NULL;
-}
-
-static void ipg_nic_rx_with_start(struct net_device *dev,
- struct ipg_nic_private *sp,
- struct ipg_rx *rxfd, unsigned entry)
-{
- struct ipg_jumbo *jumbo = &sp->jumbo;
- struct pci_dev *pdev = sp->pdev;
- struct sk_buff *skb;
-
- /* 1: found error, 0 no error */
- if (ipg_nic_rx_check_error(dev) != NORMAL_PACKET)
- return;
-
- /* accept this frame and send to upper layer */
- skb = sp->rx_buff[entry];
- if (!skb)
- return;
-
- if (jumbo->found_start)
- dev_kfree_skb_irq(jumbo->skb);
-
- pci_unmap_single(pdev, le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
-
- skb_put(skb, sp->rxfrag_size);
-
- jumbo->found_start = 1;
- jumbo->current_size = sp->rxfrag_size;
- jumbo->skb = skb;
-
- sp->rx_buff[entry] = NULL;
-}
-
-static void ipg_nic_rx_with_end(struct net_device *dev,
- struct ipg_nic_private *sp,
- struct ipg_rx *rxfd, unsigned entry)
-{
- struct ipg_jumbo *jumbo = &sp->jumbo;
-
- /* 1: found error, 0 no error */
- if (ipg_nic_rx_check_error(dev) == NORMAL_PACKET) {
- struct sk_buff *skb = sp->rx_buff[entry];
-
- if (!skb)
- return;
-
- if (jumbo->found_start) {
- int framelen, endframelen;
-
- framelen = le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFRAMELEN;
-
- endframelen = framelen - jumbo->current_size;
- if (framelen > sp->rxsupport_size)
- dev_kfree_skb_irq(jumbo->skb);
- else {
- memcpy(skb_put(jumbo->skb, endframelen),
- skb->data, endframelen);
-
- jumbo->skb->protocol =
- eth_type_trans(jumbo->skb, dev);
-
- skb_checksum_none_assert(jumbo->skb);
- netif_rx(jumbo->skb);
- }
- }
-
- jumbo->found_start = 0;
- jumbo->current_size = 0;
- jumbo->skb = NULL;
-
- ipg_nic_rx_free_skb(dev);
- } else {
- dev_kfree_skb_irq(jumbo->skb);
- jumbo->found_start = 0;
- jumbo->current_size = 0;
- jumbo->skb = NULL;
- }
-}
-
-static void ipg_nic_rx_no_start_no_end(struct net_device *dev,
- struct ipg_nic_private *sp,
- struct ipg_rx *rxfd, unsigned entry)
-{
- struct ipg_jumbo *jumbo = &sp->jumbo;
-
- /* 1: found error, 0 no error */
- if (ipg_nic_rx_check_error(dev) == NORMAL_PACKET) {
- struct sk_buff *skb = sp->rx_buff[entry];
-
- if (skb) {
- if (jumbo->found_start) {
- jumbo->current_size += sp->rxfrag_size;
- if (jumbo->current_size <= sp->rxsupport_size) {
- memcpy(skb_put(jumbo->skb,
- sp->rxfrag_size),
- skb->data, sp->rxfrag_size);
- }
- }
- ipg_nic_rx_free_skb(dev);
- }
- } else {
- dev_kfree_skb_irq(jumbo->skb);
- jumbo->found_start = 0;
- jumbo->current_size = 0;
- jumbo->skb = NULL;
- }
-}
-
-static int ipg_nic_rx_jumbo(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int curr = sp->rx_current;
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
-
- IPG_DEBUG_MSG("_nic_rx\n");
-
- for (i = 0; i < IPG_MAXRFDPROCESS_COUNT; i++, curr++) {
- unsigned int entry = curr % IPG_RFDLIST_LENGTH;
- struct ipg_rx *rxfd = sp->rxd + entry;
-
- if (!(rxfd->rfs & cpu_to_le64(IPG_RFS_RFDDONE)))
- break;
-
- switch (ipg_nic_rx_check_frame_type(dev)) {
- case FRAME_WITH_START_WITH_END:
- ipg_nic_rx_with_start_and_end(dev, sp, rxfd, entry);
- break;
- case FRAME_WITH_START:
- ipg_nic_rx_with_start(dev, sp, rxfd, entry);
- break;
- case FRAME_WITH_END:
- ipg_nic_rx_with_end(dev, sp, rxfd, entry);
- break;
- case FRAME_NO_START_NO_END:
- ipg_nic_rx_no_start_no_end(dev, sp, rxfd, entry);
- break;
- }
- }
-
- sp->rx_current = curr;
-
- if (i == IPG_MAXRFDPROCESS_COUNT) {
- /* There are more RFDs to process, however the
- * allocated amount of RFD processing time has
- * expired. Assert Interrupt Requested to make
- * sure we come back to process the remaining RFDs.
- */
- ipg_w32(ipg_r32(ASIC_CTRL) | IPG_AC_INT_REQUEST, ASIC_CTRL);
- }
-
- ipg_nic_rxrestore(dev);
-
- return 0;
-}
-
-static int ipg_nic_rx(struct net_device *dev)
-{
- /* Transfer received Ethernet frames to higher network layers. */
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int curr = sp->rx_current;
- void __iomem *ioaddr = sp->ioaddr;
- struct ipg_rx *rxfd;
- unsigned int i;
-
- IPG_DEBUG_MSG("_nic_rx\n");
-
-#define __RFS_MASK \
- cpu_to_le64(IPG_RFS_RFDDONE | IPG_RFS_FRAMESTART | IPG_RFS_FRAMEEND)
-
- for (i = 0; i < IPG_MAXRFDPROCESS_COUNT; i++, curr++) {
- unsigned int entry = curr % IPG_RFDLIST_LENGTH;
- struct sk_buff *skb = sp->rx_buff[entry];
- unsigned int framelen;
-
- rxfd = sp->rxd + entry;
-
- if (((rxfd->rfs & __RFS_MASK) != __RFS_MASK) || !skb)
- break;
-
- /* Get received frame length. */
- framelen = le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFRAMELEN;
-
- /* Check for jumbo frame arrival with too small
- * RXFRAG_SIZE.
- */
- if (framelen > sp->rxfrag_size) {
- IPG_DEBUG_MSG
- ("RFS FrameLen > allocated fragment size\n");
-
- framelen = sp->rxfrag_size;
- }
-
- if ((IPG_DROP_ON_RX_ETH_ERRORS && (le64_to_cpu(rxfd->rfs) &
- (IPG_RFS_RXFIFOOVERRUN | IPG_RFS_RXRUNTFRAME |
- IPG_RFS_RXALIGNMENTERROR | IPG_RFS_RXFCSERROR |
- IPG_RFS_RXOVERSIZEDFRAME | IPG_RFS_RXLENGTHERROR)))) {
-
- IPG_DEBUG_MSG("Rx error, RFS = %016lx\n",
- (unsigned long int) rxfd->rfs);
-
- /* Increment general receive error statistic. */
- sp->stats.rx_errors++;
-
- /* Increment detailed receive error statistics. */
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFIFOOVERRUN) {
- IPG_DEBUG_MSG("RX FIFO overrun occurred\n");
- sp->stats.rx_fifo_errors++;
- }
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXRUNTFRAME) {
- IPG_DEBUG_MSG("RX runt occurred\n");
- sp->stats.rx_length_errors++;
- }
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXOVERSIZEDFRAME) ;
- /* Do nothing, error count handled by a IPG
- * statistic register.
- */
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXALIGNMENTERROR) {
- IPG_DEBUG_MSG("RX alignment error occurred\n");
- sp->stats.rx_frame_errors++;
- }
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFCSERROR) ;
- /* Do nothing, error count handled by a IPG
- * statistic register.
- */
-
- /* Free the memory associated with the RX
- * buffer since it is erroneous and we will
- * not pass it to higher layer processes.
- */
- if (skb) {
- __le64 info = rxfd->frag_info;
-
- pci_unmap_single(sp->pdev,
- le64_to_cpu(info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
-
- dev_kfree_skb_irq(skb);
- }
- } else {
-
- /* Adjust the new buffer length to accommodate the size
- * of the received frame.
- */
- skb_put(skb, framelen);
-
- /* Set the buffer's protocol field to Ethernet. */
- skb->protocol = eth_type_trans(skb, dev);
-
- /* The IPG encountered an error with (or
- * there were no) IP/TCP/UDP checksums.
- * This may or may not indicate an invalid
- * IP/TCP/UDP frame was received. Let the
- * upper layer decide.
- */
- skb_checksum_none_assert(skb);
-
- /* Hand off frame for higher layer processing.
- * The function netif_rx() releases the sk_buff
- * when processing completes.
- */
- netif_rx(skb);
- }
-
- /* Assure RX buffer is not reused by IPG. */
- sp->rx_buff[entry] = NULL;
- }
-
- /*
- * If there are more RFDs to process and the allocated amount of RFD
- * processing time has expired, assert Interrupt Requested to make
- * sure we come back to process the remaining RFDs.
- */
- if (i == IPG_MAXRFDPROCESS_COUNT)
- ipg_w32(ipg_r32(ASIC_CTRL) | IPG_AC_INT_REQUEST, ASIC_CTRL);
-
-#ifdef IPG_DEBUG
- /* Check if the RFD list contained no receive frame data. */
- if (!i)
- sp->EmptyRFDListCount++;
-#endif
- while ((le64_to_cpu(rxfd->rfs) & IPG_RFS_RFDDONE) &&
- !((le64_to_cpu(rxfd->rfs) & IPG_RFS_FRAMESTART) &&
- (le64_to_cpu(rxfd->rfs) & IPG_RFS_FRAMEEND))) {
- unsigned int entry = curr++ % IPG_RFDLIST_LENGTH;
-
- rxfd = sp->rxd + entry;
-
- IPG_DEBUG_MSG("Frame requires multiple RFDs\n");
-
- /* An unexpected event, additional code needed to handle
- * properly. So for the time being, just disregard the
- * frame.
- */
-
- /* Free the memory associated with the RX
- * buffer since it is erroneous and we will
- * not pass it to higher layer processes.
- */
- if (sp->rx_buff[entry]) {
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
- dev_kfree_skb_irq(sp->rx_buff[entry]);
- }
-
- /* Assure RX buffer is not reused by IPG. */
- sp->rx_buff[entry] = NULL;
- }
-
- sp->rx_current = curr;
-
- /* Check to see if there are a minimum number of used
- * RFDs before restoring any (should improve performance.)
- */
- if ((curr - sp->rx_dirty) >= IPG_MINUSEDRFDSTOFREE)
- ipg_nic_rxrestore(dev);
-
- return 0;
-}
-
-static void ipg_reset_after_host_error(struct work_struct *work)
-{
- struct ipg_nic_private *sp =
- container_of(work, struct ipg_nic_private, task.work);
- struct net_device *dev = sp->dev;
-
- /*
- * Acknowledge HostError interrupt by resetting
- * IPG DMA and HOST.
- */
- ipg_reset(dev, IPG_AC_GLOBAL_RESET | IPG_AC_HOST | IPG_AC_DMA);
-
- init_rfdlist(dev);
- init_tfdlist(dev);
-
- if (ipg_io_config(dev) < 0) {
- netdev_info(dev, "Cannot recover from PCI error\n");
- schedule_delayed_work(&sp->task, HZ);
- }
-}
-
-static irqreturn_t ipg_interrupt_handler(int irq, void *dev_inst)
-{
- struct net_device *dev = dev_inst;
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int handled = 0;
- u16 status;
-
- IPG_DEBUG_MSG("_interrupt_handler\n");
-
- if (sp->is_jumbo)
- ipg_nic_rxrestore(dev);
-
- spin_lock(&sp->lock);
-
- /* Get interrupt source information, and acknowledge
- * some (i.e. TxDMAComplete, RxDMAComplete, RxEarly,
- * IntRequested, MacControlFrame, LinkEvent) interrupts
- * if issued. Also, all IPG interrupts are disabled by
- * reading IntStatusAck.
- */
- status = ipg_r16(INT_STATUS_ACK);
-
- IPG_DEBUG_MSG("IntStatusAck = %04x\n", status);
-
- /* Shared IRQ of remove event. */
- if (!(status & IPG_IS_RSVD_MASK))
- goto out_enable;
-
- handled = 1;
-
- if (unlikely(!netif_running(dev)))
- goto out_unlock;
-
- /* If RFDListEnd interrupt, restore all used RFDs. */
- if (status & IPG_IS_RFD_LIST_END) {
- IPG_DEBUG_MSG("RFDListEnd Interrupt\n");
-
- /* The RFD list end indicates an RFD was encountered
- * with a 0 NextPtr, or with an RFDDone bit set to 1
- * (indicating the RFD is not read for use by the
- * IPG.) Try to restore all RFDs.
- */
- ipg_nic_rxrestore(dev);
-
-#ifdef IPG_DEBUG
- /* Increment the RFDlistendCount counter. */
- sp->RFDlistendCount++;
-#endif
- }
-
- /* If RFDListEnd, RxDMAPriority, RxDMAComplete, or
- * IntRequested interrupt, process received frames. */
- if ((status & IPG_IS_RX_DMA_PRIORITY) ||
- (status & IPG_IS_RFD_LIST_END) ||
- (status & IPG_IS_RX_DMA_COMPLETE) ||
- (status & IPG_IS_INT_REQUESTED)) {
-#ifdef IPG_DEBUG
- /* Increment the RFD list checked counter if interrupted
- * only to check the RFD list. */
- if (status & (~(IPG_IS_RX_DMA_PRIORITY | IPG_IS_RFD_LIST_END |
- IPG_IS_RX_DMA_COMPLETE | IPG_IS_INT_REQUESTED) &
- (IPG_IS_HOST_ERROR | IPG_IS_TX_DMA_COMPLETE |
- IPG_IS_LINK_EVENT | IPG_IS_TX_COMPLETE |
- IPG_IS_UPDATE_STATS)))
- sp->RFDListCheckedCount++;
-#endif
-
- if (sp->is_jumbo)
- ipg_nic_rx_jumbo(dev);
- else
- ipg_nic_rx(dev);
- }
-
- /* If TxDMAComplete interrupt, free used TFDs. */
- if (status & IPG_IS_TX_DMA_COMPLETE)
- ipg_nic_txfree(dev);
-
- /* TxComplete interrupts indicate one of numerous actions.
- * Determine what action to take based on TXSTATUS register.
- */
- if (status & IPG_IS_TX_COMPLETE)
- ipg_nic_txcleanup(dev);
-
- /* If UpdateStats interrupt, update Linux Ethernet statistics */
- if (status & IPG_IS_UPDATE_STATS)
- ipg_nic_get_stats(dev);
-
- /* If HostError interrupt, reset IPG. */
- if (status & IPG_IS_HOST_ERROR) {
- IPG_DDEBUG_MSG("HostError Interrupt\n");
-
- schedule_delayed_work(&sp->task, 0);
- }
-
- /* If LinkEvent interrupt, resolve autonegotiation. */
- if (status & IPG_IS_LINK_EVENT) {
- if (ipg_config_autoneg(dev) < 0)
- netdev_info(dev, "Auto-negotiation error\n");
- }
-
- /* If MACCtrlFrame interrupt, do nothing. */
- if (status & IPG_IS_MAC_CTRL_FRAME)
- IPG_DEBUG_MSG("MACCtrlFrame interrupt\n");
-
- /* If RxComplete interrupt, do nothing. */
- if (status & IPG_IS_RX_COMPLETE)
- IPG_DEBUG_MSG("RxComplete interrupt\n");
-
- /* If RxEarly interrupt, do nothing. */
- if (status & IPG_IS_RX_EARLY)
- IPG_DEBUG_MSG("RxEarly interrupt\n");
-
-out_enable:
- /* Re-enable IPG interrupts. */
- ipg_w16(IPG_IE_TX_DMA_COMPLETE | IPG_IE_RX_DMA_COMPLETE |
- IPG_IE_HOST_ERROR | IPG_IE_INT_REQUESTED | IPG_IE_TX_COMPLETE |
- IPG_IE_LINK_EVENT | IPG_IE_UPDATE_STATS, INT_ENABLE);
-out_unlock:
- spin_unlock(&sp->lock);
-
- return IRQ_RETVAL(handled);
-}
-
-static void ipg_rx_clear(struct ipg_nic_private *sp)
-{
- unsigned int i;
-
- for (i = 0; i < IPG_RFDLIST_LENGTH; i++) {
- if (sp->rx_buff[i]) {
- struct ipg_rx *rxfd = sp->rxd + i;
-
- dev_kfree_skb_irq(sp->rx_buff[i]);
- sp->rx_buff[i] = NULL;
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
- }
- }
-}
-
-static void ipg_tx_clear(struct ipg_nic_private *sp)
-{
- unsigned int i;
-
- for (i = 0; i < IPG_TFDLIST_LENGTH; i++) {
- if (sp->tx_buff[i]) {
- struct ipg_tx *txfd = sp->txd + i;
-
- pci_unmap_single(sp->pdev,
- le64_to_cpu(txfd->frag_info) & ~IPG_TFI_FRAGLEN,
- sp->tx_buff[i]->len, PCI_DMA_TODEVICE);
-
- dev_kfree_skb_irq(sp->tx_buff[i]);
-
- sp->tx_buff[i] = NULL;
- }
- }
-}
-
-static int ipg_nic_open(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- struct pci_dev *pdev = sp->pdev;
- int rc;
-
- IPG_DEBUG_MSG("_nic_open\n");
-
- sp->rx_buf_sz = sp->rxsupport_size;
-
- /* Check for interrupt line conflicts, and request interrupt
- * line for IPG.
- *
- * IMPORTANT: Disable IPG interrupts prior to registering
- * IRQ.
- */
- ipg_w16(0x0000, INT_ENABLE);
-
- /* Register the interrupt line to be used by the IPG within
- * the Linux system.
- */
- rc = request_irq(pdev->irq, ipg_interrupt_handler, IRQF_SHARED,
- dev->name, dev);
- if (rc < 0) {
- netdev_info(dev, "Error when requesting interrupt\n");
- goto out;
- }
-
- dev->irq = pdev->irq;
-
- rc = -ENOMEM;
-
- sp->rxd = dma_alloc_coherent(&pdev->dev, IPG_RX_RING_BYTES,
- &sp->rxd_map, GFP_KERNEL);
- if (!sp->rxd)
- goto err_free_irq_0;
-
- sp->txd = dma_alloc_coherent(&pdev->dev, IPG_TX_RING_BYTES,
- &sp->txd_map, GFP_KERNEL);
- if (!sp->txd)
- goto err_free_rx_1;
-
- rc = init_rfdlist(dev);
- if (rc < 0) {
- netdev_info(dev, "Error during configuration\n");
- goto err_free_tx_2;
- }
-
- init_tfdlist(dev);
-
- rc = ipg_io_config(dev);
- if (rc < 0) {
- netdev_info(dev, "Error during configuration\n");
- goto err_release_tfdlist_3;
- }
-
- /* Resolve autonegotiation. */
- if (ipg_config_autoneg(dev) < 0)
- netdev_info(dev, "Auto-negotiation error\n");
-
- /* initialize JUMBO Frame control variable */
- sp->jumbo.found_start = 0;
- sp->jumbo.current_size = 0;
- sp->jumbo.skb = NULL;
-
- /* Enable transmit and receive operation of the IPG. */
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_RX_ENABLE | IPG_MC_TX_ENABLE) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
-
- netif_start_queue(dev);
-out:
- return rc;
-
-err_release_tfdlist_3:
- ipg_tx_clear(sp);
- ipg_rx_clear(sp);
-err_free_tx_2:
- dma_free_coherent(&pdev->dev, IPG_TX_RING_BYTES, sp->txd, sp->txd_map);
-err_free_rx_1:
- dma_free_coherent(&pdev->dev, IPG_RX_RING_BYTES, sp->rxd, sp->rxd_map);
-err_free_irq_0:
- free_irq(pdev->irq, dev);
- goto out;
-}
-
-static int ipg_nic_stop(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- struct pci_dev *pdev = sp->pdev;
-
- IPG_DEBUG_MSG("_nic_stop\n");
-
- netif_stop_queue(dev);
-
- IPG_DUMPTFDLIST(dev);
-
- do {
- (void) ipg_r16(INT_STATUS_ACK);
-
- ipg_reset(dev, IPG_AC_GLOBAL_RESET | IPG_AC_HOST | IPG_AC_DMA);
-
- synchronize_irq(pdev->irq);
- } while (ipg_r16(INT_ENABLE) & IPG_IE_RSVD_MASK);
-
- ipg_rx_clear(sp);
-
- ipg_tx_clear(sp);
-
- pci_free_consistent(pdev, IPG_RX_RING_BYTES, sp->rxd, sp->rxd_map);
- pci_free_consistent(pdev, IPG_TX_RING_BYTES, sp->txd, sp->txd_map);
-
- free_irq(pdev->irq, dev);
-
- return 0;
-}
-
-static netdev_tx_t ipg_nic_hard_start_xmit(struct sk_buff *skb,
- struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int entry = sp->tx_current % IPG_TFDLIST_LENGTH;
- unsigned long flags;
- struct ipg_tx *txfd;
-
- IPG_DDEBUG_MSG("_nic_hard_start_xmit\n");
-
- /* If in 10Mbps mode, stop the transmit queue so
- * no more transmit frames are accepted.
- */
- if (sp->tenmbpsmode)
- netif_stop_queue(dev);
-
- if (sp->reset_current_tfd) {
- sp->reset_current_tfd = 0;
- entry = 0;
- }
-
- txfd = sp->txd + entry;
-
- sp->tx_buff[entry] = skb;
-
- /* Clear all TFC fields, except TFDDONE. */
- txfd->tfc = cpu_to_le64(IPG_TFC_TFDDONE);
-
- /* Specify the TFC field within the TFD. */
- txfd->tfc |= cpu_to_le64(IPG_TFC_WORDALIGNDISABLED |
- (IPG_TFC_FRAMEID & sp->tx_current) |
- (IPG_TFC_FRAGCOUNT & (1 << 24)));
- /*
- * 16--17 (WordAlign) <- 3 (disable),
- * 0--15 (FrameId) <- sp->tx_current,
- * 24--27 (FragCount) <- 1
- */
-
- /* Request TxComplete interrupts at an interval defined
- * by the constant IPG_FRAMESBETWEENTXCOMPLETES.
- * Request TxComplete interrupt for every frame
- * if in 10Mbps mode to accommodate problem with 10Mbps
- * processing.
- */
- if (sp->tenmbpsmode)
- txfd->tfc |= cpu_to_le64(IPG_TFC_TXINDICATE);
- txfd->tfc |= cpu_to_le64(IPG_TFC_TXDMAINDICATE);
- /* Based on compilation option, determine if FCS is to be
- * appended to transmit frame by IPG.
- */
- if (!(IPG_APPEND_FCS_ON_TX))
- txfd->tfc |= cpu_to_le64(IPG_TFC_FCSAPPENDDISABLE);
-
- /* Based on compilation option, determine if IP, TCP and/or
- * UDP checksums are to be added to transmit frame by IPG.
- */
- if (IPG_ADD_IPCHECKSUM_ON_TX)
- txfd->tfc |= cpu_to_le64(IPG_TFC_IPCHECKSUMENABLE);
-
- if (IPG_ADD_TCPCHECKSUM_ON_TX)
- txfd->tfc |= cpu_to_le64(IPG_TFC_TCPCHECKSUMENABLE);
-
- if (IPG_ADD_UDPCHECKSUM_ON_TX)
- txfd->tfc |= cpu_to_le64(IPG_TFC_UDPCHECKSUMENABLE);
-
- /* Based on compilation option, determine if VLAN tag info is to be
- * inserted into transmit frame by IPG.
- */
- if (IPG_INSERT_MANUAL_VLAN_TAG) {
- txfd->tfc |= cpu_to_le64(IPG_TFC_VLANTAGINSERT |
- ((u64) IPG_MANUAL_VLAN_VID << 32) |
- ((u64) IPG_MANUAL_VLAN_CFI << 44) |
- ((u64) IPG_MANUAL_VLAN_USERPRIORITY << 45));
- }
-
- /* The fragment start location within system memory is defined
- * by the sk_buff structure's data field. The physical address
- * of this location within the system's virtual memory space
- * is determined using the IPG_HOST2BUS_MAP function.
- */
- txfd->frag_info = cpu_to_le64(pci_map_single(sp->pdev, skb->data,
- skb->len, PCI_DMA_TODEVICE));
-
- /* The length of the fragment within system memory is defined by
- * the sk_buff structure's len field.
- */
- txfd->frag_info |= cpu_to_le64(IPG_TFI_FRAGLEN &
- ((u64) (skb->len & 0xffff) << 48));
-
- /* Clear the TFDDone bit last to indicate the TFD is ready
- * for transfer to the IPG.
- */
- txfd->tfc &= cpu_to_le64(~IPG_TFC_TFDDONE);
-
- spin_lock_irqsave(&sp->lock, flags);
-
- sp->tx_current++;
-
- mmiowb();
-
- ipg_w32(IPG_DC_TX_DMA_POLL_NOW, DMA_CTRL);
-
- if (sp->tx_current == (sp->tx_dirty + IPG_TFDLIST_LENGTH))
- netif_stop_queue(dev);
-
- spin_unlock_irqrestore(&sp->lock, flags);
-
- return NETDEV_TX_OK;
-}
-
-static void ipg_set_phy_default_param(unsigned char rev,
- struct net_device *dev, int phy_address)
-{
- unsigned short length;
- unsigned char revision;
- const unsigned short *phy_param;
- unsigned short address, value;
-
- phy_param = &DefaultPhyParam[0];
- length = *phy_param & 0x00FF;
- revision = (unsigned char)((*phy_param) >> 8);
- phy_param++;
- while (length != 0) {
- if (rev == revision) {
- while (length > 1) {
- address = *phy_param;
- value = *(phy_param + 1);
- phy_param += 2;
- mdio_write(dev, phy_address, address, value);
- length -= 4;
- }
- break;
- } else {
- phy_param += length / 2;
- length = *phy_param & 0x00FF;
- revision = (unsigned char)((*phy_param) >> 8);
- phy_param++;
- }
- }
-}
-
-static int read_eeprom(struct net_device *dev, int eep_addr)
-{
- void __iomem *ioaddr = ipg_ioaddr(dev);
- unsigned int i;
- int ret = 0;
- u16 value;
-
- value = IPG_EC_EEPROM_READOPCODE | (eep_addr & 0xff);
- ipg_w16(value, EEPROM_CTRL);
-
- for (i = 0; i < 1000; i++) {
- u16 data;
-
- mdelay(10);
- data = ipg_r16(EEPROM_CTRL);
- if (!(data & IPG_EC_EEPROM_BUSY)) {
- ret = ipg_r16(EEPROM_DATA);
- break;
- }
- }
- return ret;
-}
-
-static void ipg_init_mii(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- struct mii_if_info *mii_if = &sp->mii_if;
- int phyaddr;
-
- mii_if->dev = dev;
- mii_if->mdio_read = mdio_read;
- mii_if->mdio_write = mdio_write;
- mii_if->phy_id_mask = 0x1f;
- mii_if->reg_num_mask = 0x1f;
-
- mii_if->phy_id = phyaddr = ipg_find_phyaddr(dev);
-
- if (phyaddr != 0x1f) {
- u16 mii_phyctrl, mii_1000cr;
-
- mii_1000cr = mdio_read(dev, phyaddr, MII_CTRL1000);
- mii_1000cr |= ADVERTISE_1000FULL | ADVERTISE_1000HALF |
- GMII_PHY_1000BASETCONTROL_PreferMaster;
- mdio_write(dev, phyaddr, MII_CTRL1000, mii_1000cr);
-
- mii_phyctrl = mdio_read(dev, phyaddr, MII_BMCR);
-
- /* Set default phyparam */
- ipg_set_phy_default_param(sp->pdev->revision, dev, phyaddr);
-
- /* Reset PHY */
- mii_phyctrl |= BMCR_RESET | BMCR_ANRESTART;
- mdio_write(dev, phyaddr, MII_BMCR, mii_phyctrl);
-
- }
-}
-
-static int ipg_hw_init(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
- int rc;
-
- /* Read/Write and Reset EEPROM Value */
- /* Read LED Mode Configuration from EEPROM */
- sp->led_mode = read_eeprom(dev, 6);
-
- /* Reset all functions within the IPG. Do not assert
- * RST_OUT as not compatible with some PHYs.
- */
- rc = ipg_reset(dev, IPG_RESET_MASK);
- if (rc < 0)
- goto out;
-
- ipg_init_mii(dev);
-
- /* Read MAC Address from EEPROM */
- for (i = 0; i < 3; i++)
- sp->station_addr[i] = read_eeprom(dev, 16 + i);
-
- for (i = 0; i < 3; i++)
- ipg_w16(sp->station_addr[i], STATION_ADDRESS_0 + 2*i);
-
- /* Set station address in ethernet_device structure. */
- dev->dev_addr[0] = ipg_r16(STATION_ADDRESS_0) & 0x00ff;
- dev->dev_addr[1] = (ipg_r16(STATION_ADDRESS_0) & 0xff00) >> 8;
- dev->dev_addr[2] = ipg_r16(STATION_ADDRESS_1) & 0x00ff;
- dev->dev_addr[3] = (ipg_r16(STATION_ADDRESS_1) & 0xff00) >> 8;
- dev->dev_addr[4] = ipg_r16(STATION_ADDRESS_2) & 0x00ff;
- dev->dev_addr[5] = (ipg_r16(STATION_ADDRESS_2) & 0xff00) >> 8;
-out:
- return rc;
-}
-
-static int ipg_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int rc;
-
- mutex_lock(&sp->mii_mutex);
- rc = generic_mii_ioctl(&sp->mii_if, if_mii(ifr), cmd, NULL);
- mutex_unlock(&sp->mii_mutex);
-
- return rc;
-}
-
-static int ipg_nic_change_mtu(struct net_device *dev, int new_mtu)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int err;
-
- /* Function to accommodate changes to Maximum Transfer Unit
- * (or MTU) of IPG NIC. Cannot use default function since
- * the default will not allow for MTU > 1500 bytes.
- */
-
- IPG_DEBUG_MSG("_nic_change_mtu\n");
-
- /*
- * Check that the new MTU value is between 68 (14 byte header, 46 byte
- * payload, 4 byte FCS) and 10 KB, which is the largest supported MTU.
- */
- if (new_mtu < 68 || new_mtu > 10240)
- return -EINVAL;
-
- err = ipg_nic_stop(dev);
- if (err)
- return err;
-
- dev->mtu = new_mtu;
-
- sp->max_rxframe_size = new_mtu;
-
- sp->rxfrag_size = new_mtu;
- if (sp->rxfrag_size > 4088)
- sp->rxfrag_size = 4088;
-
- sp->rxsupport_size = sp->max_rxframe_size;
-
- if (new_mtu > 0x0600)
- sp->is_jumbo = true;
- else
- sp->is_jumbo = false;
-
- return ipg_nic_open(dev);
-}
-
-static int ipg_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int rc;
-
- mutex_lock(&sp->mii_mutex);
- rc = mii_ethtool_gset(&sp->mii_if, cmd);
- mutex_unlock(&sp->mii_mutex);
-
- return rc;
-}
-
-static int ipg_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int rc;
-
- mutex_lock(&sp->mii_mutex);
- rc = mii_ethtool_sset(&sp->mii_if, cmd);
- mutex_unlock(&sp->mii_mutex);
-
- return rc;
-}
-
-static int ipg_nway_reset(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int rc;
-
- mutex_lock(&sp->mii_mutex);
- rc = mii_nway_restart(&sp->mii_if);
- mutex_unlock(&sp->mii_mutex);
-
- return rc;
-}
-
-static const struct ethtool_ops ipg_ethtool_ops = {
- .get_settings = ipg_get_settings,
- .set_settings = ipg_set_settings,
- .nway_reset = ipg_nway_reset,
-};
-
-static void ipg_remove(struct pci_dev *pdev)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
- struct ipg_nic_private *sp = netdev_priv(dev);
-
- IPG_DEBUG_MSG("_remove\n");
-
- /* Un-register Ethernet device. */
- unregister_netdev(dev);
-
- pci_iounmap(pdev, sp->ioaddr);
-
- pci_release_regions(pdev);
-
- free_netdev(dev);
- pci_disable_device(pdev);
-}
-
-static const struct net_device_ops ipg_netdev_ops = {
- .ndo_open = ipg_nic_open,
- .ndo_stop = ipg_nic_stop,
- .ndo_start_xmit = ipg_nic_hard_start_xmit,
- .ndo_get_stats = ipg_nic_get_stats,
- .ndo_set_rx_mode = ipg_nic_set_multicast_list,
- .ndo_do_ioctl = ipg_ioctl,
- .ndo_tx_timeout = ipg_tx_timeout,
- .ndo_change_mtu = ipg_nic_change_mtu,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_validate_addr = eth_validate_addr,
-};
-
-static int ipg_probe(struct pci_dev *pdev, const struct pci_device_id *id)
-{
- unsigned int i = id->driver_data;
- struct ipg_nic_private *sp;
- struct net_device *dev;
- void __iomem *ioaddr;
- int rc;
-
- rc = pci_enable_device(pdev);
- if (rc < 0)
- goto out;
-
- pr_info("%s: %s\n", pci_name(pdev), ipg_brand_name[i]);
-
- pci_set_master(pdev);
-
- rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(40));
- if (rc < 0) {
- rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
- if (rc < 0) {
- pr_err("%s: DMA config failed\n", pci_name(pdev));
- goto err_disable_0;
- }
- }
-
- /*
- * Initialize net device.
- */
- dev = alloc_etherdev(sizeof(struct ipg_nic_private));
- if (!dev) {
- rc = -ENOMEM;
- goto err_disable_0;
- }
-
- sp = netdev_priv(dev);
- spin_lock_init(&sp->lock);
- mutex_init(&sp->mii_mutex);
-
- sp->is_jumbo = IPG_IS_JUMBO;
- sp->rxfrag_size = IPG_RXFRAG_SIZE;
- sp->rxsupport_size = IPG_RXSUPPORT_SIZE;
- sp->max_rxframe_size = IPG_MAX_RXFRAME_SIZE;
-
- /* Declare IPG NIC functions for Ethernet device methods.
- */
- dev->netdev_ops = &ipg_netdev_ops;
- SET_NETDEV_DEV(dev, &pdev->dev);
- dev->ethtool_ops = &ipg_ethtool_ops;
-
- rc = pci_request_regions(pdev, DRV_NAME);
- if (rc)
- goto err_free_dev_1;
-
- ioaddr = pci_iomap(pdev, 1, pci_resource_len(pdev, 1));
- if (!ioaddr) {
- pr_err("%s: cannot map MMIO\n", pci_name(pdev));
- rc = -EIO;
- goto err_release_regions_2;
- }
-
- /* Save the pointer to the PCI device information. */
- sp->ioaddr = ioaddr;
- sp->pdev = pdev;
- sp->dev = dev;
-
- INIT_DELAYED_WORK(&sp->task, ipg_reset_after_host_error);
-
- pci_set_drvdata(pdev, dev);
-
- rc = ipg_hw_init(dev);
- if (rc < 0)
- goto err_unmap_3;
-
- rc = register_netdev(dev);
- if (rc < 0)
- goto err_unmap_3;
-
- netdev_info(dev, "Ethernet device registered\n");
-out:
- return rc;
-
-err_unmap_3:
- pci_iounmap(pdev, ioaddr);
-err_release_regions_2:
- pci_release_regions(pdev);
-err_free_dev_1:
- free_netdev(dev);
-err_disable_0:
- pci_disable_device(pdev);
- goto out;
-}
-
-static struct pci_driver ipg_pci_driver = {
- .name = IPG_DRIVER_NAME,
- .id_table = ipg_pci_tbl,
- .probe = ipg_probe,
- .remove = ipg_remove,
-};
-
-module_pci_driver(ipg_pci_driver);
diff --git a/drivers/net/ethernet/icplus/ipg.h b/drivers/net/ethernet/icplus/ipg.h
deleted file mode 100644
index de60628..0000000
--- a/drivers/net/ethernet/icplus/ipg.h
+++ /dev/null
@@ -1,748 +0,0 @@
-/*
- * Include file for Gigabit Ethernet device driver for Network
- * Interface Cards (NICs) utilizing the Tamarack Microelectronics
- * Inc. IPG Gigabit or Triple Speed Ethernet Media Access
- * Controller.
- */
-#ifndef __LINUX_IPG_H
-#define __LINUX_IPG_H
-
-#include <linux/module.h>
-
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/errno.h>
-#include <asm/io.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <asm/bitops.h>
-
-/*
- * Constants
- */
-
-/* GMII based PHY IDs */
-#define NS 0x2000
-#define MARVELL 0x0141
-#define ICPLUS_PHY 0x243
-
-/* NIC Physical Layer Device MII register fields. */
-#define MII_PHY_SELECTOR_IEEE8023 0x0001
-#define MII_PHY_TECHABILITYFIELD 0x1FE0
-
-/* GMII_PHY_1000 need to set to prefer master */
-#define GMII_PHY_1000BASETCONTROL_PreferMaster 0x0400
-
-/* NIC Physical Layer Device GMII constants. */
-#define GMII_PREAMBLE 0xFFFFFFFF
-#define GMII_ST 0x1
-#define GMII_READ 0x2
-#define GMII_WRITE 0x1
-#define GMII_TA_READ_MASK 0x1
-#define GMII_TA_WRITE 0x2
-
-/* I/O register offsets. */
-enum ipg_regs {
- DMA_CTRL = 0x00,
- RX_DMA_STATUS = 0x08, /* Unused + reserved */
- TFD_LIST_PTR_0 = 0x10,
- TFD_LIST_PTR_1 = 0x14,
- TX_DMA_BURST_THRESH = 0x18,
- TX_DMA_URGENT_THRESH = 0x19,
- TX_DMA_POLL_PERIOD = 0x1a,
- RFD_LIST_PTR_0 = 0x1c,
- RFD_LIST_PTR_1 = 0x20,
- RX_DMA_BURST_THRESH = 0x24,
- RX_DMA_URGENT_THRESH = 0x25,
- RX_DMA_POLL_PERIOD = 0x26,
- DEBUG_CTRL = 0x2c,
- ASIC_CTRL = 0x30,
- FIFO_CTRL = 0x38, /* Unused */
- FLOW_OFF_THRESH = 0x3c,
- FLOW_ON_THRESH = 0x3e,
- EEPROM_DATA = 0x48,
- EEPROM_CTRL = 0x4a,
- EXPROM_ADDR = 0x4c, /* Unused */
- EXPROM_DATA = 0x50, /* Unused */
- WAKE_EVENT = 0x51, /* Unused */
- COUNTDOWN = 0x54, /* Unused */
- INT_STATUS_ACK = 0x5a,
- INT_ENABLE = 0x5c,
- INT_STATUS = 0x5e, /* Unused */
- TX_STATUS = 0x60,
- MAC_CTRL = 0x6c,
- VLAN_TAG = 0x70, /* Unused */
- PHY_SET = 0x75,
- PHY_CTRL = 0x76,
- STATION_ADDRESS_0 = 0x78,
- STATION_ADDRESS_1 = 0x7a,
- STATION_ADDRESS_2 = 0x7c,
- MAX_FRAME_SIZE = 0x86,
- RECEIVE_MODE = 0x88,
- HASHTABLE_0 = 0x8c,
- HASHTABLE_1 = 0x90,
- RMON_STATISTICS_MASK = 0x98,
- STATISTICS_MASK = 0x9c,
- RX_JUMBO_FRAMES = 0xbc, /* Unused */
- TCP_CHECKSUM_ERRORS = 0xc0, /* Unused */
- IP_CHECKSUM_ERRORS = 0xc2, /* Unused */
- UDP_CHECKSUM_ERRORS = 0xc4, /* Unused */
- TX_JUMBO_FRAMES = 0xf4 /* Unused */
-};
-
-/* Ethernet MIB statistic register offsets. */
-#define IPG_OCTETRCVOK 0xA8
-#define IPG_MCSTOCTETRCVDOK 0xAC
-#define IPG_BCSTOCTETRCVOK 0xB0
-#define IPG_FRAMESRCVDOK 0xB4
-#define IPG_MCSTFRAMESRCVDOK 0xB8
-#define IPG_BCSTFRAMESRCVDOK 0xBE
-#define IPG_MACCONTROLFRAMESRCVD 0xC6
-#define IPG_FRAMETOOLONGERRORS 0xC8
-#define IPG_INRANGELENGTHERRORS 0xCA
-#define IPG_FRAMECHECKSEQERRORS 0xCC
-#define IPG_FRAMESLOSTRXERRORS 0xCE
-#define IPG_OCTETXMTOK 0xD0
-#define IPG_MCSTOCTETXMTOK 0xD4
-#define IPG_BCSTOCTETXMTOK 0xD8
-#define IPG_FRAMESXMTDOK 0xDC
-#define IPG_MCSTFRAMESXMTDOK 0xE0
-#define IPG_FRAMESWDEFERREDXMT 0xE4
-#define IPG_LATECOLLISIONS 0xE8
-#define IPG_MULTICOLFRAMES 0xEC
-#define IPG_SINGLECOLFRAMES 0xF0
-#define IPG_BCSTFRAMESXMTDOK 0xF6
-#define IPG_CARRIERSENSEERRORS 0xF8
-#define IPG_MACCONTROLFRAMESXMTDOK 0xFA
-#define IPG_FRAMESABORTXSCOLLS 0xFC
-#define IPG_FRAMESWEXDEFERRAL 0xFE
-
-/* RMON statistic register offsets. */
-#define IPG_ETHERSTATSCOLLISIONS 0x100
-#define IPG_ETHERSTATSOCTETSTRANSMIT 0x104
-#define IPG_ETHERSTATSPKTSTRANSMIT 0x108
-#define IPG_ETHERSTATSPKTS64OCTESTSTRANSMIT 0x10C
-#define IPG_ETHERSTATSPKTS65TO127OCTESTSTRANSMIT 0x110
-#define IPG_ETHERSTATSPKTS128TO255OCTESTSTRANSMIT 0x114
-#define IPG_ETHERSTATSPKTS256TO511OCTESTSTRANSMIT 0x118
-#define IPG_ETHERSTATSPKTS512TO1023OCTESTSTRANSMIT 0x11C
-#define IPG_ETHERSTATSPKTS1024TO1518OCTESTSTRANSMIT 0x120
-#define IPG_ETHERSTATSCRCALIGNERRORS 0x124
-#define IPG_ETHERSTATSUNDERSIZEPKTS 0x128
-#define IPG_ETHERSTATSFRAGMENTS 0x12C
-#define IPG_ETHERSTATSJABBERS 0x130
-#define IPG_ETHERSTATSOCTETS 0x134
-#define IPG_ETHERSTATSPKTS 0x138
-#define IPG_ETHERSTATSPKTS64OCTESTS 0x13C
-#define IPG_ETHERSTATSPKTS65TO127OCTESTS 0x140
-#define IPG_ETHERSTATSPKTS128TO255OCTESTS 0x144
-#define IPG_ETHERSTATSPKTS256TO511OCTESTS 0x148
-#define IPG_ETHERSTATSPKTS512TO1023OCTESTS 0x14C
-#define IPG_ETHERSTATSPKTS1024TO1518OCTESTS 0x150
-
-/* RMON statistic register equivalents. */
-#define IPG_ETHERSTATSMULTICASTPKTSTRANSMIT 0xE0
-#define IPG_ETHERSTATSBROADCASTPKTSTRANSMIT 0xF6
-#define IPG_ETHERSTATSMULTICASTPKTS 0xB8
-#define IPG_ETHERSTATSBROADCASTPKTS 0xBE
-#define IPG_ETHERSTATSOVERSIZEPKTS 0xC8
-#define IPG_ETHERSTATSDROPEVENTS 0xCE
-
-/* Serial EEPROM offsets */
-#define IPG_EEPROM_CONFIGPARAM 0x00
-#define IPG_EEPROM_ASICCTRL 0x01
-#define IPG_EEPROM_SUBSYSTEMVENDORID 0x02
-#define IPG_EEPROM_SUBSYSTEMID 0x03
-#define IPG_EEPROM_STATIONADDRESS0 0x10
-#define IPG_EEPROM_STATIONADDRESS1 0x11
-#define IPG_EEPROM_STATIONADDRESS2 0x12
-
-/* Register & data structure bit masks */
-
-/* PCI register masks. */
-
-/* IOBaseAddress */
-#define IPG_PIB_RSVD_MASK 0xFFFFFE01
-#define IPG_PIB_IOBASEADDRESS 0xFFFFFF00
-#define IPG_PIB_IOBASEADDRIND 0x00000001
-
-/* MemBaseAddress */
-#define IPG_PMB_RSVD_MASK 0xFFFFFE07
-#define IPG_PMB_MEMBASEADDRIND 0x00000001
-#define IPG_PMB_MEMMAPTYPE 0x00000006
-#define IPG_PMB_MEMMAPTYPE0 0x00000002
-#define IPG_PMB_MEMMAPTYPE1 0x00000004
-#define IPG_PMB_MEMBASEADDRESS 0xFFFFFE00
-
-/* ConfigStatus */
-#define IPG_CS_RSVD_MASK 0xFFB0
-#define IPG_CS_CAPABILITIES 0x0010
-#define IPG_CS_66MHZCAPABLE 0x0020
-#define IPG_CS_FASTBACK2BACK 0x0080
-#define IPG_CS_DATAPARITYREPORTED 0x0100
-#define IPG_CS_DEVSELTIMING 0x0600
-#define IPG_CS_SIGNALEDTARGETABORT 0x0800
-#define IPG_CS_RECEIVEDTARGETABORT 0x1000
-#define IPG_CS_RECEIVEDMASTERABORT 0x2000
-#define IPG_CS_SIGNALEDSYSTEMERROR 0x4000
-#define IPG_CS_DETECTEDPARITYERROR 0x8000
-
-/* TFD data structure masks. */
-
-/* TFDList, TFC */
-#define IPG_TFC_RSVD_MASK 0x0000FFFF9FFFFFFFULL
-#define IPG_TFC_FRAMEID 0x000000000000FFFFULL
-#define IPG_TFC_WORDALIGN 0x0000000000030000ULL
-#define IPG_TFC_WORDALIGNTODWORD 0x0000000000000000ULL
-#define IPG_TFC_WORDALIGNTOWORD 0x0000000000020000ULL
-#define IPG_TFC_WORDALIGNDISABLED 0x0000000000030000ULL
-#define IPG_TFC_TCPCHECKSUMENABLE 0x0000000000040000ULL
-#define IPG_TFC_UDPCHECKSUMENABLE 0x0000000000080000ULL
-#define IPG_TFC_IPCHECKSUMENABLE 0x0000000000100000ULL
-#define IPG_TFC_FCSAPPENDDISABLE 0x0000000000200000ULL
-#define IPG_TFC_TXINDICATE 0x0000000000400000ULL
-#define IPG_TFC_TXDMAINDICATE 0x0000000000800000ULL
-#define IPG_TFC_FRAGCOUNT 0x000000000F000000ULL
-#define IPG_TFC_VLANTAGINSERT 0x0000000010000000ULL
-#define IPG_TFC_TFDDONE 0x0000000080000000ULL
-#define IPG_TFC_VID 0x00000FFF00000000ULL
-#define IPG_TFC_CFI 0x0000100000000000ULL
-#define IPG_TFC_USERPRIORITY 0x0000E00000000000ULL
-
-/* TFDList, FragInfo */
-#define IPG_TFI_RSVD_MASK 0xFFFF00FFFFFFFFFFULL
-#define IPG_TFI_FRAGADDR 0x000000FFFFFFFFFFULL
-#define IPG_TFI_FRAGLEN 0xFFFF000000000000ULL
-
-/* RFD data structure masks. */
-
-/* RFDList, RFS */
-#define IPG_RFS_RSVD_MASK 0x0000FFFFFFFFFFFFULL
-#define IPG_RFS_RXFRAMELEN 0x000000000000FFFFULL
-#define IPG_RFS_RXFIFOOVERRUN 0x0000000000010000ULL
-#define IPG_RFS_RXRUNTFRAME 0x0000000000020000ULL
-#define IPG_RFS_RXALIGNMENTERROR 0x0000000000040000ULL
-#define IPG_RFS_RXFCSERROR 0x0000000000080000ULL
-#define IPG_RFS_RXOVERSIZEDFRAME 0x0000000000100000ULL
-#define IPG_RFS_RXLENGTHERROR 0x0000000000200000ULL
-#define IPG_RFS_VLANDETECTED 0x0000000000400000ULL
-#define IPG_RFS_TCPDETECTED 0x0000000000800000ULL
-#define IPG_RFS_TCPERROR 0x0000000001000000ULL
-#define IPG_RFS_UDPDETECTED 0x0000000002000000ULL
-#define IPG_RFS_UDPERROR 0x0000000004000000ULL
-#define IPG_RFS_IPDETECTED 0x0000000008000000ULL
-#define IPG_RFS_IPERROR 0x0000000010000000ULL
-#define IPG_RFS_FRAMESTART 0x0000000020000000ULL
-#define IPG_RFS_FRAMEEND 0x0000000040000000ULL
-#define IPG_RFS_RFDDONE 0x0000000080000000ULL
-#define IPG_RFS_TCI 0x0000FFFF00000000ULL
-
-/* RFDList, FragInfo */
-#define IPG_RFI_RSVD_MASK 0xFFFF00FFFFFFFFFFULL
-#define IPG_RFI_FRAGADDR 0x000000FFFFFFFFFFULL
-#define IPG_RFI_FRAGLEN 0xFFFF000000000000ULL
-
-/* I/O Register masks. */
-
-/* RMON Statistics Mask */
-#define IPG_RZ_ALL 0x0FFFFFFF
-
-/* Statistics Mask */
-#define IPG_SM_ALL 0x0FFFFFFF
-#define IPG_SM_OCTETRCVOK_FRAMESRCVDOK 0x00000001
-#define IPG_SM_MCSTOCTETRCVDOK_MCSTFRAMESRCVDOK 0x00000002
-#define IPG_SM_BCSTOCTETRCVDOK_BCSTFRAMESRCVDOK 0x00000004
-#define IPG_SM_RXJUMBOFRAMES 0x00000008
-#define IPG_SM_TCPCHECKSUMERRORS 0x00000010
-#define IPG_SM_IPCHECKSUMERRORS 0x00000020
-#define IPG_SM_UDPCHECKSUMERRORS 0x00000040
-#define IPG_SM_MACCONTROLFRAMESRCVD 0x00000080
-#define IPG_SM_FRAMESTOOLONGERRORS 0x00000100
-#define IPG_SM_INRANGELENGTHERRORS 0x00000200
-#define IPG_SM_FRAMECHECKSEQERRORS 0x00000400
-#define IPG_SM_FRAMESLOSTRXERRORS 0x00000800
-#define IPG_SM_OCTETXMTOK_FRAMESXMTOK 0x00001000
-#define IPG_SM_MCSTOCTETXMTOK_MCSTFRAMESXMTDOK 0x00002000
-#define IPG_SM_BCSTOCTETXMTOK_BCSTFRAMESXMTDOK 0x00004000
-#define IPG_SM_FRAMESWDEFERREDXMT 0x00008000
-#define IPG_SM_LATECOLLISIONS 0x00010000
-#define IPG_SM_MULTICOLFRAMES 0x00020000
-#define IPG_SM_SINGLECOLFRAMES 0x00040000
-#define IPG_SM_TXJUMBOFRAMES 0x00080000
-#define IPG_SM_CARRIERSENSEERRORS 0x00100000
-#define IPG_SM_MACCONTROLFRAMESXMTD 0x00200000
-#define IPG_SM_FRAMESABORTXSCOLLS 0x00400000
-#define IPG_SM_FRAMESWEXDEFERAL 0x00800000
-
-/* Countdown */
-#define IPG_CD_RSVD_MASK 0x0700FFFF
-#define IPG_CD_COUNT 0x0000FFFF
-#define IPG_CD_COUNTDOWNSPEED 0x01000000
-#define IPG_CD_COUNTDOWNMODE 0x02000000
-#define IPG_CD_COUNTINTENABLED 0x04000000
-
-/* TxDMABurstThresh */
-#define IPG_TB_RSVD_MASK 0xFF
-
-/* TxDMAUrgentThresh */
-#define IPG_TU_RSVD_MASK 0xFF
-
-/* TxDMAPollPeriod */
-#define IPG_TP_RSVD_MASK 0xFF
-
-/* RxDMAUrgentThresh */
-#define IPG_RU_RSVD_MASK 0xFF
-
-/* RxDMAPollPeriod */
-#define IPG_RP_RSVD_MASK 0xFF
-
-/* ReceiveMode */
-#define IPG_RM_RSVD_MASK 0x3F
-#define IPG_RM_RECEIVEUNICAST 0x01
-#define IPG_RM_RECEIVEMULTICAST 0x02
-#define IPG_RM_RECEIVEBROADCAST 0x04
-#define IPG_RM_RECEIVEALLFRAMES 0x08
-#define IPG_RM_RECEIVEMULTICASTHASH 0x10
-#define IPG_RM_RECEIVEIPMULTICAST 0x20
-
-/* PhySet */
-#define IPG_PS_MEM_LENB9B 0x01
-#define IPG_PS_MEM_LEN9 0x02
-#define IPG_PS_NON_COMPDET 0x04
-
-/* PhyCtrl */
-#define IPG_PC_RSVD_MASK 0xFF
-#define IPG_PC_MGMTCLK_LO 0x00
-#define IPG_PC_MGMTCLK_HI 0x01
-#define IPG_PC_MGMTCLK 0x01
-#define IPG_PC_MGMTDATA 0x02
-#define IPG_PC_MGMTDIR 0x04
-#define IPG_PC_DUPLEX_POLARITY 0x08
-#define IPG_PC_DUPLEX_STATUS 0x10
-#define IPG_PC_LINK_POLARITY 0x20
-#define IPG_PC_LINK_SPEED 0xC0
-#define IPG_PC_LINK_SPEED_10MBPS 0x40
-#define IPG_PC_LINK_SPEED_100MBPS 0x80
-#define IPG_PC_LINK_SPEED_1000MBPS 0xC0
-
-/* DMACtrl */
-#define IPG_DC_RSVD_MASK 0xC07D9818
-#define IPG_DC_RX_DMA_COMPLETE 0x00000008
-#define IPG_DC_RX_DMA_POLL_NOW 0x00000010
-#define IPG_DC_TX_DMA_COMPLETE 0x00000800
-#define IPG_DC_TX_DMA_POLL_NOW 0x00001000
-#define IPG_DC_TX_DMA_IN_PROG 0x00008000
-#define IPG_DC_RX_EARLY_DISABLE 0x00010000
-#define IPG_DC_MWI_DISABLE 0x00040000
-#define IPG_DC_TX_WRITE_BACK_DISABLE 0x00080000
-#define IPG_DC_TX_BURST_LIMIT 0x00700000
-#define IPG_DC_TARGET_ABORT 0x40000000
-#define IPG_DC_MASTER_ABORT 0x80000000
-
-/* ASICCtrl */
-#define IPG_AC_RSVD_MASK 0x07FFEFF2
-#define IPG_AC_EXP_ROM_SIZE 0x00000002
-#define IPG_AC_PHY_SPEED10 0x00000010
-#define IPG_AC_PHY_SPEED100 0x00000020
-#define IPG_AC_PHY_SPEED1000 0x00000040
-#define IPG_AC_PHY_MEDIA 0x00000080
-#define IPG_AC_FORCED_CFG 0x00000700
-#define IPG_AC_D3RESETDISABLE 0x00000800
-#define IPG_AC_SPEED_UP_MODE 0x00002000
-#define IPG_AC_LED_MODE 0x00004000
-#define IPG_AC_RST_OUT_POLARITY 0x00008000
-#define IPG_AC_GLOBAL_RESET 0x00010000
-#define IPG_AC_RX_RESET 0x00020000
-#define IPG_AC_TX_RESET 0x00040000
-#define IPG_AC_DMA 0x00080000
-#define IPG_AC_FIFO 0x00100000
-#define IPG_AC_NETWORK 0x00200000
-#define IPG_AC_HOST 0x00400000
-#define IPG_AC_AUTO_INIT 0x00800000
-#define IPG_AC_RST_OUT 0x01000000
-#define IPG_AC_INT_REQUEST 0x02000000
-#define IPG_AC_RESET_BUSY 0x04000000
-#define IPG_AC_LED_SPEED 0x08000000
-#define IPG_AC_LED_MODE_BIT_1 0x20000000
-
-/* EepromCtrl */
-#define IPG_EC_RSVD_MASK 0x83FF
-#define IPG_EC_EEPROM_ADDR 0x00FF
-#define IPG_EC_EEPROM_OPCODE 0x0300
-#define IPG_EC_EEPROM_SUBCOMMAD 0x0000
-#define IPG_EC_EEPROM_WRITEOPCODE 0x0100
-#define IPG_EC_EEPROM_READOPCODE 0x0200
-#define IPG_EC_EEPROM_ERASEOPCODE 0x0300
-#define IPG_EC_EEPROM_BUSY 0x8000
-
-/* FIFOCtrl */
-#define IPG_FC_RSVD_MASK 0xC001
-#define IPG_FC_RAM_TEST_MODE 0x0001
-#define IPG_FC_TRANSMITTING 0x4000
-#define IPG_FC_RECEIVING 0x8000
-
-/* TxStatus */
-#define IPG_TS_RSVD_MASK 0xFFFF00DD
-#define IPG_TS_TX_ERROR 0x00000001
-#define IPG_TS_LATE_COLLISION 0x00000004
-#define IPG_TS_TX_MAX_COLL 0x00000008
-#define IPG_TS_TX_UNDERRUN 0x00000010
-#define IPG_TS_TX_IND_REQD 0x00000040
-#define IPG_TS_TX_COMPLETE 0x00000080
-#define IPG_TS_TX_FRAMEID 0xFFFF0000
-
-/* WakeEvent */
-#define IPG_WE_WAKE_PKT_ENABLE 0x01
-#define IPG_WE_MAGIC_PKT_ENABLE 0x02
-#define IPG_WE_LINK_EVT_ENABLE 0x04
-#define IPG_WE_WAKE_POLARITY 0x08
-#define IPG_WE_WAKE_PKT_EVT 0x10
-#define IPG_WE_MAGIC_PKT_EVT 0x20
-#define IPG_WE_LINK_EVT 0x40
-#define IPG_WE_WOL_ENABLE 0x80
-
-/* IntEnable */
-#define IPG_IE_RSVD_MASK 0x1FFE
-#define IPG_IE_HOST_ERROR 0x0002
-#define IPG_IE_TX_COMPLETE 0x0004
-#define IPG_IE_MAC_CTRL_FRAME 0x0008
-#define IPG_IE_RX_COMPLETE 0x0010
-#define IPG_IE_RX_EARLY 0x0020
-#define IPG_IE_INT_REQUESTED 0x0040
-#define IPG_IE_UPDATE_STATS 0x0080
-#define IPG_IE_LINK_EVENT 0x0100
-#define IPG_IE_TX_DMA_COMPLETE 0x0200
-#define IPG_IE_RX_DMA_COMPLETE 0x0400
-#define IPG_IE_RFD_LIST_END 0x0800
-#define IPG_IE_RX_DMA_PRIORITY 0x1000
-
-/* IntStatus */
-#define IPG_IS_RSVD_MASK 0x1FFF
-#define IPG_IS_INTERRUPT_STATUS 0x0001
-#define IPG_IS_HOST_ERROR 0x0002
-#define IPG_IS_TX_COMPLETE 0x0004
-#define IPG_IS_MAC_CTRL_FRAME 0x0008
-#define IPG_IS_RX_COMPLETE 0x0010
-#define IPG_IS_RX_EARLY 0x0020
-#define IPG_IS_INT_REQUESTED 0x0040
-#define IPG_IS_UPDATE_STATS 0x0080
-#define IPG_IS_LINK_EVENT 0x0100
-#define IPG_IS_TX_DMA_COMPLETE 0x0200
-#define IPG_IS_RX_DMA_COMPLETE 0x0400
-#define IPG_IS_RFD_LIST_END 0x0800
-#define IPG_IS_RX_DMA_PRIORITY 0x1000
-
-/* MACCtrl */
-#define IPG_MC_RSVD_MASK 0x7FE33FA3
-#define IPG_MC_IFS_SELECT 0x00000003
-#define IPG_MC_IFS_4352BIT 0x00000003
-#define IPG_MC_IFS_1792BIT 0x00000002
-#define IPG_MC_IFS_1024BIT 0x00000001
-#define IPG_MC_IFS_96BIT 0x00000000
-#define IPG_MC_DUPLEX_SELECT 0x00000020
-#define IPG_MC_DUPLEX_SELECT_FD 0x00000020
-#define IPG_MC_DUPLEX_SELECT_HD 0x00000000
-#define IPG_MC_TX_FLOW_CONTROL_ENABLE 0x00000080
-#define IPG_MC_RX_FLOW_CONTROL_ENABLE 0x00000100
-#define IPG_MC_RCV_FCS 0x00000200
-#define IPG_MC_FIFO_LOOPBACK 0x00000400
-#define IPG_MC_MAC_LOOPBACK 0x00000800
-#define IPG_MC_AUTO_VLAN_TAGGING 0x00001000
-#define IPG_MC_AUTO_VLAN_UNTAGGING 0x00002000
-#define IPG_MC_COLLISION_DETECT 0x00010000
-#define IPG_MC_CARRIER_SENSE 0x00020000
-#define IPG_MC_STATISTICS_ENABLE 0x00200000
-#define IPG_MC_STATISTICS_DISABLE 0x00400000
-#define IPG_MC_STATISTICS_ENABLED 0x00800000
-#define IPG_MC_TX_ENABLE 0x01000000
-#define IPG_MC_TX_DISABLE 0x02000000
-#define IPG_MC_TX_ENABLED 0x04000000
-#define IPG_MC_RX_ENABLE 0x08000000
-#define IPG_MC_RX_DISABLE 0x10000000
-#define IPG_MC_RX_ENABLED 0x20000000
-#define IPG_MC_PAUSED 0x40000000
-
-/*
- * Tune
- */
-
-/* Assign IPG_APPEND_FCS_ON_TX > 0 for auto FCS append on TX. */
-#define IPG_APPEND_FCS_ON_TX 1
-
-/* Assign IPG_APPEND_FCS_ON_TX > 0 for auto FCS strip on RX. */
-#define IPG_STRIP_FCS_ON_RX 1
-
-/* Assign IPG_DROP_ON_RX_ETH_ERRORS > 0 to drop RX frames with
- * Ethernet errors.
- */
-#define IPG_DROP_ON_RX_ETH_ERRORS 1
-
-/* Assign IPG_INSERT_MANUAL_VLAN_TAG > 0 to insert VLAN tags manually
- * (via TFC).
- */
-#define IPG_INSERT_MANUAL_VLAN_TAG 0
-
-/* Assign IPG_ADD_IPCHECKSUM_ON_TX > 0 for auto IP checksum on TX. */
-#define IPG_ADD_IPCHECKSUM_ON_TX 0
-
-/* Assign IPG_ADD_TCPCHECKSUM_ON_TX > 0 for auto TCP checksum on TX.
- * DO NOT USE FOR SILICON REVISIONS B3 AND EARLIER.
- */
-#define IPG_ADD_TCPCHECKSUM_ON_TX 0
-
-/* Assign IPG_ADD_UDPCHECKSUM_ON_TX > 0 for auto UDP checksum on TX.
- * DO NOT USE FOR SILICON REVISIONS B3 AND EARLIER.
- */
-#define IPG_ADD_UDPCHECKSUM_ON_TX 0
-
-/* If inserting VLAN tags manually, assign the IPG_MANUAL_VLAN_xx
- * constants as desired.
- */
-#define IPG_MANUAL_VLAN_VID 0xABC
-#define IPG_MANUAL_VLAN_CFI 0x1
-#define IPG_MANUAL_VLAN_USERPRIORITY 0x5
-
-#define IPG_IO_REG_RANGE 0xFF
-#define IPG_MEM_REG_RANGE 0x154
-#define IPG_DRIVER_NAME "Sundance Technology IPG Triple-Speed Ethernet"
-#define IPG_NIC_PHY_ADDRESS 0x01
-#define IPG_DMALIST_ALIGN_PAD 0x07
-#define IPG_MULTICAST_HASHTABLE_SIZE 0x40
-
-/* Number of milliseconds to wait after issuing a software reset.
- * 0x05 <= IPG_AC_RESETWAIT to account for proper 10Mbps operation.
- */
-#define IPG_AC_RESETWAIT 0x05
-
-/* Number of IPG_AC_RESETWAIT timeperiods before declaring timeout. */
-#define IPG_AC_RESET_TIMEOUT 0x0A
-
-/* Minimum number of nanoseconds used to toggle MDC clock during
- * MII/GMII register access.
- */
-#define IPG_PC_PHYCTRLWAIT_NS 200
-
-#define IPG_TFDLIST_LENGTH 0x100
-
-/* Number of frames between TxDMAComplete interrupt.
- * 0 < IPG_FRAMESBETWEENTXDMACOMPLETES <= IPG_TFDLIST_LENGTH
- */
-#define IPG_FRAMESBETWEENTXDMACOMPLETES 0x1
-
-#define IPG_RFDLIST_LENGTH 0x100
-
-/* Maximum number of RFDs to process per interrupt.
- * 1 < IPG_MAXRFDPROCESS_COUNT < IPG_RFDLIST_LENGTH
- */
-#define IPG_MAXRFDPROCESS_COUNT 0x80
-
-/* Minimum margin between last freed RFD, and current RFD.
- * 1 < IPG_MINUSEDRFDSTOFREE < IPG_RFDLIST_LENGTH
- */
-#define IPG_MINUSEDRFDSTOFREE 0x80
-
-/* specify the jumbo frame maximum size
- * per unit is 0x600 (the rx_buffer size that one RFD can carry)
- */
-#define MAX_JUMBOSIZE 0x8 /* max is 12K */
-
-/* Key register values loaded at driver start up. */
-
-/* TXDMAPollPeriod is specified in 320ns increments.
- *
- * Value Time
- * ---------------------
- * 0x00-0x01 320ns
- * 0x03 ~1us
- * 0x1F ~10us
- * 0xFF ~82us
- */
-#define IPG_TXDMAPOLLPERIOD_VALUE 0x26
-
-/* TxDMAUrgentThresh specifies the minimum amount of
- * data in the transmit FIFO before asserting an
- * urgent transmit DMA request.
- *
- * Value Min TxFIFO occupied space before urgent TX request
- * ---------------------------------------------------------------
- * 0x00-0x04 128 bytes (1024 bits)
- * 0x27 1248 bytes (~10000 bits)
- * 0x30 1536 bytes (12288 bits)
- * 0xFF 8192 bytes (65535 bits)
- */
-#define IPG_TXDMAURGENTTHRESH_VALUE 0x04
-
-/* TxDMABurstThresh specifies the minimum amount of
- * free space in the transmit FIFO before asserting an
- * transmit DMA request.
- *
- * Value Min TxFIFO free space before TX request
- * ----------------------------------------------------
- * 0x00-0x08 256 bytes
- * 0x30 1536 bytes
- * 0xFF 8192 bytes
- */
-#define IPG_TXDMABURSTTHRESH_VALUE 0x30
-
-/* RXDMAPollPeriod is specified in 320ns increments.
- *
- * Value Time
- * ---------------------
- * 0x00-0x01 320ns
- * 0x03 ~1us
- * 0x1F ~10us
- * 0xFF ~82us
- */
-#define IPG_RXDMAPOLLPERIOD_VALUE 0x01
-
-/* RxDMAUrgentThresh specifies the minimum amount of
- * free space within the receive FIFO before asserting
- * a urgent receive DMA request.
- *
- * Value Min RxFIFO free space before urgent RX request
- * ---------------------------------------------------------------
- * 0x00-0x04 128 bytes (1024 bits)
- * 0x27 1248 bytes (~10000 bits)
- * 0x30 1536 bytes (12288 bits)
- * 0xFF 8192 bytes (65535 bits)
- */
-#define IPG_RXDMAURGENTTHRESH_VALUE 0x30
-
-/* RxDMABurstThresh specifies the minimum amount of
- * occupied space within the receive FIFO before asserting
- * a receive DMA request.
- *
- * Value Min TxFIFO free space before TX request
- * ----------------------------------------------------
- * 0x00-0x08 256 bytes
- * 0x30 1536 bytes
- * 0xFF 8192 bytes
- */
-#define IPG_RXDMABURSTTHRESH_VALUE 0x30
-
-/* FlowOnThresh specifies the maximum amount of occupied
- * space in the receive FIFO before a PAUSE frame with
- * maximum pause time transmitted.
- *
- * Value Max RxFIFO occupied space before PAUSE
- * ---------------------------------------------------
- * 0x0000 0 bytes
- * 0x0740 29,696 bytes
- * 0x07FF 32,752 bytes
- */
-#define IPG_FLOWONTHRESH_VALUE 0x0740
-
-/* FlowOffThresh specifies the minimum amount of occupied
- * space in the receive FIFO before a PAUSE frame with
- * zero pause time is transmitted.
- *
- * Value Max RxFIFO occupied space before PAUSE
- * ---------------------------------------------------
- * 0x0000 0 bytes
- * 0x00BF 3056 bytes
- * 0x07FF 32,752 bytes
- */
-#define IPG_FLOWOFFTHRESH_VALUE 0x00BF
-
-/*
- * Miscellaneous macros.
- */
-
-/* Macros for printing debug statements. */
-#ifdef IPG_DEBUG
-# define IPG_DEBUG_MSG(fmt, args...) \
-do { \
- if (0) \
- printk(KERN_DEBUG "IPG: " fmt, ##args); \
-} while (0)
-# define IPG_DDEBUG_MSG(fmt, args...) \
- printk(KERN_DEBUG "IPG: " fmt, ##args)
-# define IPG_DUMPRFDLIST(args) ipg_dump_rfdlist(args)
-# define IPG_DUMPTFDLIST(args) ipg_dump_tfdlist(args)
-#else
-# define IPG_DEBUG_MSG(fmt, args...) \
-do { \
- if (0) \
- printk(KERN_DEBUG "IPG: " fmt, ##args); \
-} while (0)
-# define IPG_DDEBUG_MSG(fmt, args...) \
-do { \
- if (0) \
- printk(KERN_DEBUG "IPG: " fmt, ##args); \
-} while (0)
-# define IPG_DUMPRFDLIST(args)
-# define IPG_DUMPTFDLIST(args)
-#endif
-
-/*
- * End miscellaneous macros.
- */
-
-/* Transmit Frame Descriptor. The IPG supports 15 fragments,
- * however Linux requires only a single fragment. Note, each
- * TFD field is 64 bits wide.
- */
-struct ipg_tx {
- __le64 next_desc;
- __le64 tfc;
- __le64 frag_info;
-};
-
-/* Receive Frame Descriptor. Note, each RFD field is 64 bits wide.
- */
-struct ipg_rx {
- __le64 next_desc;
- __le64 rfs;
- __le64 frag_info;
-};
-
-struct ipg_jumbo {
- int found_start;
- int current_size;
- struct sk_buff *skb;
-};
-
-/* Structure of IPG NIC specific data. */
-struct ipg_nic_private {
- void __iomem *ioaddr;
- struct ipg_tx *txd;
- struct ipg_rx *rxd;
- dma_addr_t txd_map;
- dma_addr_t rxd_map;
- struct sk_buff *tx_buff[IPG_TFDLIST_LENGTH];
- struct sk_buff *rx_buff[IPG_RFDLIST_LENGTH];
- unsigned int tx_current;
- unsigned int tx_dirty;
- unsigned int rx_current;
- unsigned int rx_dirty;
- bool is_jumbo;
- struct ipg_jumbo jumbo;
- unsigned long rxfrag_size;
- unsigned long rxsupport_size;
- unsigned long max_rxframe_size;
- unsigned int rx_buf_sz;
- struct pci_dev *pdev;
- struct net_device *dev;
- struct net_device_stats stats;
- spinlock_t lock;
- int tenmbpsmode;
-
- u16 led_mode;
- u16 station_addr[3]; /* Station Address in EEPROM Reg 0x10..0x12 */
-
- struct mutex mii_mutex;
- struct mii_if_info mii_if;
- int reset_current_tfd;
-#ifdef IPG_DEBUG
- int RFDlistendCount;
- int RFDListCheckedCount;
- int EmptyRFDListCount;
-#endif
- struct delayed_work task;
-};
-
-#endif /* __LINUX_IPG_H */
--
Ondrej Zary
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards
2015-11-15 21:36 [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards Ondrej Zary
2015-11-15 21:36 ` [PATCH 2/2] ipg: Remove ipg driver Ondrej Zary
@ 2015-11-16 8:41 ` Andy Shevchenko
2015-11-16 22:11 ` David Miller
2 siblings, 0 replies; 5+ messages in thread
From: Andy Shevchenko @ 2015-11-16 8:41 UTC (permalink / raw)
To: Ondrej Zary
Cc: netdev, Francois Romieu, David Miller, Kernel development list
On Sun, Nov 15, 2015 at 11:36 PM, Ondrej Zary
<linux@rainbow-software.org> wrote:
> Add support for IP1000A chips to dl2k driver.
> IP1000A chip looks like a TC9020 with integrated PHY.
>
> This allows IP1000A chips to work reliably because the ipg driver is
> buggy - it loses packets under load and then completely stops
> transmitting data.
>
> Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
> vendor=0x13f0 device=0x1023 (rev 0x41)
> subsystem vendor=0x1043 device=0x8180
>
> MAC address registers access needed to be changed from 8-bit to 16-bit
> because 8-bit does not work on IP1000A. 8-bit access is not even
> allowed in the TC9020 datasheet (although it worked). 16-bit access
> works on both.
>
> Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
> a rebranded TC9020):
> vendor=0x1186 device=0x4000 (rev 0x0c)
> subsystem vendor=0x1186 device=0x4000
>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
> Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
> ---
> drivers/net/ethernet/dlink/Kconfig | 5 ++--
> drivers/net/ethernet/dlink/dl2k.c | 55 ++++++++++++++++++++++++++++++++++--
> drivers/net/ethernet/dlink/dl2k.h | 15 +++++++++-
> 3 files changed, 69 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/net/ethernet/dlink/Kconfig b/drivers/net/ethernet/dlink/Kconfig
> index f6e858d..ebdc832 100644
> --- a/drivers/net/ethernet/dlink/Kconfig
> +++ b/drivers/net/ethernet/dlink/Kconfig
> @@ -17,15 +17,16 @@ config NET_VENDOR_DLINK
> if NET_VENDOR_DLINK
>
> config DL2K
> - tristate "DL2000/TC902x-based Gigabit Ethernet support"
> + tristate "DL2000/TC902x/IP1000A-based Gigabit Ethernet support"
> depends on PCI
> select CRC32
> ---help---
> - This driver supports DL2000/TC902x-based Gigabit ethernet cards,
> + This driver supports DL2000/TC902x/IP1000A-based Gigabit ethernet cards,
> which includes
> D-Link DGE-550T Gigabit Ethernet Adapter.
> D-Link DL2000-based Gigabit Ethernet Adapter.
> Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
> + ICPlus IP1000A-based cards
>
> To compile this driver as a module, choose M here: the
> module will be called dl2k.
> diff --git a/drivers/net/ethernet/dlink/dl2k.c b/drivers/net/ethernet/dlink/dl2k.c
> index cf0a5fc..ccca479 100644
> --- a/drivers/net/ethernet/dlink/dl2k.c
> +++ b/drivers/net/ethernet/dlink/dl2k.c
> @@ -253,6 +253,19 @@ rio_probe1 (struct pci_dev *pdev, const struct pci_device_id *ent)
> if (err)
> goto err_out_unmap_rx;
>
> + if (np->chip_id == CHIP_IP1000A &&
> + (np->pdev->revision == 0x40 || np->pdev->revision == 0x41)) {
> + /* PHY magic taken from ipg driver, undocumented registers */
> + mii_write(dev, np->phy_addr, 31, 0x0001);
> + mii_write(dev, np->phy_addr, 27, 0x01e0);
> + mii_write(dev, np->phy_addr, 31, 0x0002);
> + mii_write(dev, np->phy_addr, 27, 0xeb8e);
> + mii_write(dev, np->phy_addr, 31, 0x0000);
> + mii_write(dev, np->phy_addr, 30, 0x005e);
> + /* advertise 1000BASE-T half & full duplex, prefer MASTER */
> + mii_write(dev, np->phy_addr, MII_CTRL1000, 0x0700);
> + }
> +
> /* Fiber device? */
> np->phy_media = (dr16(ASICCtrl) & PhyMedia) ? 1 : 0;
> np->link_status = 0;
> @@ -361,6 +374,11 @@ parse_eeprom (struct net_device *dev)
> for (i = 0; i < 6; i++)
> dev->dev_addr[i] = psrom->mac_addr[i];
>
> + if (np->chip_id == CHIP_IP1000A) {
> + np->led_mode = psrom->led_mode;
> + return 0;
> + }
> +
> if (np->pdev->vendor != PCI_VENDOR_ID_DLINK) {
> return 0;
> }
> @@ -406,6 +424,28 @@ parse_eeprom (struct net_device *dev)
> return 0;
> }
>
> +static void rio_set_led_mode(struct net_device *dev)
> +{
> + struct netdev_private *np = netdev_priv(dev);
> + void __iomem *ioaddr = np->ioaddr;
> + u32 mode;
> +
> + if (np->chip_id != CHIP_IP1000A)
> + return;
> +
> + mode = dr32(ASICCtrl);
> + mode &= ~(IPG_AC_LED_MODE_BIT_1 | IPG_AC_LED_MODE | IPG_AC_LED_SPEED);
> +
> + if (np->led_mode & 0x01)
> + mode |= IPG_AC_LED_MODE;
> + if (np->led_mode & 0x02)
> + mode |= IPG_AC_LED_MODE_BIT_1;
> + if (np->led_mode & 0x08)
> + mode |= IPG_AC_LED_SPEED;
> +
> + dw32(ASICCtrl, mode);
> +}
> +
> static int
> rio_open (struct net_device *dev)
> {
> @@ -424,6 +464,8 @@ rio_open (struct net_device *dev)
> GlobalReset | DMAReset | FIFOReset | NetworkReset | HostReset);
> mdelay(10);
>
> + rio_set_led_mode(dev);
> +
> /* DebugCtrl bit 4, 5, 9 must set */
> dw32(DebugCtrl, dr32(DebugCtrl) | 0x0230);
>
> @@ -433,9 +475,13 @@ rio_open (struct net_device *dev)
>
> alloc_list (dev);
>
> - /* Get station address */
> - for (i = 0; i < 6; i++)
> - dw8(StationAddr0 + i, dev->dev_addr[i]);
> + /* Set station address */
> + /* 16 or 32-bit access is required by TC9020 datasheet but 8-bit works
> + * too. However, it doesn't work on IP1000A so we use 16-bit access.
> + */
> + for (i = 0; i < 3; i++)
> + dw16(StationAddr0 + 2 * i,
> + cpu_to_le16(((u16 *)dev->dev_addr)[i]));
>
> set_multicast (dev);
> if (np->coalesce) {
> @@ -780,6 +826,7 @@ tx_error (struct net_device *dev, int tx_status)
> break;
> mdelay (1);
> }
> + rio_set_led_mode(dev);
> rio_free_tx (dev, 1);
> /* Reset TFDListPtr */
> dw32(TFDListPtr0, np->tx_ring_dma +
> @@ -799,6 +846,7 @@ tx_error (struct net_device *dev, int tx_status)
> break;
> mdelay (1);
> }
> + rio_set_led_mode(dev);
> /* Let TxStartThresh stay default value */
> }
> /* Maximum Collisions */
> @@ -965,6 +1013,7 @@ rio_error (struct net_device *dev, int int_status)
> dev->name, int_status);
> dw16(ASICCtrl + 2, GlobalReset | HostReset);
> mdelay (500);
> + rio_set_led_mode(dev);
> }
> }
>
> diff --git a/drivers/net/ethernet/dlink/dl2k.h b/drivers/net/ethernet/dlink/dl2k.h
> index 23c07b0..8f4f612 100644
> --- a/drivers/net/ethernet/dlink/dl2k.h
> +++ b/drivers/net/ethernet/dlink/dl2k.h
> @@ -211,6 +211,10 @@ enum ASICCtrl_HiWord_bits {
> ResetBusy = 0x0400,
> };
>
> +#define IPG_AC_LED_MODE BIT(14)
> +#define IPG_AC_LED_SPEED BIT(27)
> +#define IPG_AC_LED_MODE_BIT_1 BIT(29)
> +
> /* Transmit Frame Control bits */
> enum TFC_bits {
> DwordAlign = 0x00000000,
> @@ -332,7 +336,10 @@ typedef struct t_SROM {
> u16 asic_ctrl; /* 0x02 */
> u16 sub_vendor_id; /* 0x04 */
> u16 sub_system_id; /* 0x06 */
> - u16 reserved1[12]; /* 0x08-0x1f */
> + u16 pci_base_1; /* 0x08 (IP1000A only) */
> + u16 pci_base_2; /* 0x0a (IP1000A only) */
> + u16 led_mode; /* 0x0c (IP1000A only) */
> + u16 reserved1[9]; /* 0x0e-0x1f */
> u8 mac_addr[6]; /* 0x20-0x25 */
> u8 reserved2[10]; /* 0x26-0x2f */
> u8 sib[204]; /* 0x30-0xfb */
> @@ -397,6 +404,7 @@ struct netdev_private {
> u16 advertising; /* NWay media advertisement */
> u16 negotiate; /* Negotiated media */
> int phy_addr; /* PHY addresses. */
> + u16 led_mode; /* LED mode read from EEPROM (IP1000A only) */
> };
>
> /* The station address location in the EEPROM. */
> @@ -407,10 +415,15 @@ struct netdev_private {
> class_mask of the class are honored during the comparison.
> driver_data Data private to the driver.
> */
> +#define CHIP_IP1000A 1
>
> static const struct pci_device_id rio_pci_tbl[] = {
> {0x1186, 0x4000, PCI_ANY_ID, PCI_ANY_ID, },
> {0x13f0, 0x1021, PCI_ANY_ID, PCI_ANY_ID, },
> + { PCI_VDEVICE(SUNDANCE, 0x1023), CHIP_IP1000A },
> + { PCI_VDEVICE(SUNDANCE, 0x2021), CHIP_IP1000A },
> + { PCI_VDEVICE(DLINK, 0x9021), CHIP_IP1000A },
> + { PCI_VDEVICE(DLINK, 0x4020), CHIP_IP1000A },
> { }
> };
> MODULE_DEVICE_TABLE (pci, rio_pci_tbl);
> --
> Ondrej Zary
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
--
With Best Regards,
Andy Shevchenko
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards
2015-11-15 21:36 [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards Ondrej Zary
2015-11-15 21:36 ` [PATCH 2/2] ipg: Remove ipg driver Ondrej Zary
2015-11-16 8:41 ` [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards Andy Shevchenko
@ 2015-11-16 22:11 ` David Miller
2 siblings, 0 replies; 5+ messages in thread
From: David Miller @ 2015-11-16 22:11 UTC (permalink / raw)
To: linux; +Cc: netdev, romieu, linux-kernel
From: Ondrej Zary <linux@rainbow-software.org>
Date: Sun, 15 Nov 2015 22:36:11 +0100
> Add support for IP1000A chips to dl2k driver.
> IP1000A chip looks like a TC9020 with integrated PHY.
>
> This allows IP1000A chips to work reliably because the ipg driver is
> buggy - it loses packets under load and then completely stops
> transmitting data.
>
> Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
> vendor=0x13f0 device=0x1023 (rev 0x41)
> subsystem vendor=0x1043 device=0x8180
>
> MAC address registers access needed to be changed from 8-bit to 16-bit
> because 8-bit does not work on IP1000A. 8-bit access is not even
> allowed in the TC9020 datasheet (although it worked). 16-bit access
> works on both.
>
> Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
> a rebranded TC9020):
> vendor=0x1186 device=0x4000 (rev 0x0c)
> subsystem vendor=0x1186 device=0x4000
>
> Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Ok, this is a major step forward, thanks for doing this work.
Applied.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 2/2] ipg: Remove ipg driver
2015-11-15 21:36 ` [PATCH 2/2] ipg: Remove ipg driver Ondrej Zary
@ 2015-11-16 22:12 ` David Miller
0 siblings, 0 replies; 5+ messages in thread
From: David Miller @ 2015-11-16 22:12 UTC (permalink / raw)
To: linux; +Cc: netdev, romieu, linux-kernel
From: Ondrej Zary <linux@rainbow-software.org>
Date: Sun, 15 Nov 2015 22:36:12 +0100
> Now that IP1000A chips are supported by dl2k driver, the buggy ipg
> driver can be removed.
>
> Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Also applied, thanks again.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2015-11-16 22:12 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-11-15 21:36 [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards Ondrej Zary
2015-11-15 21:36 ` [PATCH 2/2] ipg: Remove ipg driver Ondrej Zary
2015-11-16 22:12 ` David Miller
2015-11-16 8:41 ` [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards Andy Shevchenko
2015-11-16 22:11 ` David Miller
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.