* [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
@ 2016-08-25 21:39 Timur Tabi
2016-08-27 4:29 ` David Miller
` (2 more replies)
0 siblings, 3 replies; 17+ messages in thread
From: Timur Tabi @ 2016-08-25 21:39 UTC (permalink / raw)
To: netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
sdharia-sgV2jX0FEOL9JmXXK+q4OQ, shankerd-sgV2jX0FEOL9JmXXK+q4OQ,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, cov-sgV2jX0FEOL9JmXXK+q4OQ,
gavidov-sgV2jX0FEOL9JmXXK+q4OQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
andrew-g2DYL2Zd6BY, bjorn.andersson-QSEj5FYQhm4dnm+yROfE0A,
mlangsdo-H+wXaHxf7aLQT0dZR+AlfA, jcm-H+wXaHxf7aLQT0dZR+AlfA,
agross-sgV2jX0FEOL9JmXXK+q4OQ, davem-fT/PcQaiUtIeIZ0/mPfg9Q,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, LinoSanfilippo-Mmb7MZpHnFY
Add support for the Qualcomm Technologies, Inc. EMAC gigabit Ethernet
controller.
This driver supports the following features:
1) Checksum offload.
2) Interrupt coalescing support.
3) SGMII phy.
4) phylib interface for external phy
Based on original work by
Niranjana Vishwanathapura <nvishwan-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Gilad Avidov <gavidov-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Timur Tabi <timur-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
v9:
- Define a separate DT node for the internal phy
- Kconfig option now selects required PHYLIB
- Use netdev_alloc_skb_ip_align
- Use devm functions for enabling clocks
- Remove redundancy from the Makefile
- Fix error messages and clean up error paths
- Miscellaneous reformatting
.../devicetree/bindings/net/qcom-emac.txt | 112 ++
MAINTAINERS | 6 +
drivers/net/ethernet/qualcomm/Kconfig | 12 +
drivers/net/ethernet/qualcomm/Makefile | 2 +
drivers/net/ethernet/qualcomm/emac/Makefile | 7 +
drivers/net/ethernet/qualcomm/emac/emac-mac.c | 1530 ++++++++++++++++++++
drivers/net/ethernet/qualcomm/emac/emac-mac.h | 248 ++++
drivers/net/ethernet/qualcomm/emac/emac-phy.c | 203 +++
drivers/net/ethernet/qualcomm/emac/emac-phy.h | 33 +
drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 722 +++++++++
drivers/net/ethernet/qualcomm/emac/emac-sgmii.h | 24 +
drivers/net/ethernet/qualcomm/emac/emac.c | 751 ++++++++++
drivers/net/ethernet/qualcomm/emac/emac.h | 335 +++++
13 files changed, 3985 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/qcom-emac.txt
create mode 100644 drivers/net/ethernet/qualcomm/emac/Makefile
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.c
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.h
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.c
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.h
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.c
create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.h
diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt
new file mode 100644
index 0000000..4599c78
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qcom-emac.txt
@@ -0,0 +1,112 @@
+Qualcomm Technologies EMAC Gigabit Ethernet Controller
+
+This network controller consists of two devices: a MAC and an SGMII
+internal PHY. Each device is represented by a device tree node. A phandle
+connects the MAC node to its corresponding internal phy node. Another
+phandle points to the external PHY node.
+
+Required properties:
+
+MAC node:
+- compatible : Should be "qcom,fsm9900-emac".
+- reg : Offset and length of the register regions for the device
+- interrupts : Interrupt number used by this controller
+- mac-address : The 6-byte MAC address. If present, it is the default
+ MAC address.
+- internal-phy : phandle to the internal PHY node
+- phy-handle : phandle the the external PHY node
+
+Internal PHY node:
+- compatible : Should be "qcom,fsm9900-emac-sgmii" or "qcom,qdf2432-emac-sgmii".
+- reg : Offset and length of the register region(s) for the device
+- interrupts : Interrupt number used by this controller
+
+The external phy child node:
+- reg : The phy address
+
+Example:
+
+FSM9900:
+
+soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ emac0: ethernet@feb20000 {
+ compatible = "qcom,fsm9900-emac";
+ reg = <0xfeb20000 0x10000>,
+ <0xfeb36000 0x1000>;
+ interrupts = <76>;
+
+ clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>,
+ <&gcc 6>, <&gcc 7>;
+ clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk",
+ "mdio_clk", "tx_clk", "rx_clk", "sys_clk";
+
+ internal-phy = <&emac_sgmii>;
+
+ phy-handle = <&phy0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins_a>;
+ };
+
+ emac_sgmii: ethernet@feb38000 {
+ compatible = "qcom,fsm9900-emac-sgmii";
+ reg = <0xfeb38000 0x1000>;
+ interrupts = <80>;
+ };
+
+ tlmm: pinctrl@fd510000 {
+ compatible = "qcom,fsm9900-pinctrl";
+
+ mdio_pins_a: mdio {
+ state {
+ pins = "gpio123", "gpio124";
+ function = "mdio";
+ };
+ };
+ };
+
+
+QDF2432:
+
+soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ emac0: ethernet@38800000 {
+ compatible = "qcom,fsm9900-emac";
+ reg = <0x0 0x38800000 0x0 0x10000>,
+ <0x0 0x38816000 0x0 0x1000>;
+ interrupts = <0 0x100 0>;
+
+ clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>,
+ <&gcc 6>, <&gcc 7>;
+ clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk",
+ "mdio_clk", "tx_clk", "rx_clk", "sys_clk";
+
+ internal-phy = <&emac_sgmii>;
+
+ phy-handle = <&phy0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@4 {
+ reg = <4>;
+ };
+ };
+
+ emac_sgmii: ethernet@410400 {
+ compatible = "qcom,qdf2432-emac-sgmii";
+ reg = <0x0 0x00410400 0x0 0xc00>, /* Base address */
+ <0x0 0x00410000 0x0 0x400>; /* Pre-lane digital */
+ interrupts = <0 0x104 0>;
+ };
+
diff --git a/MAINTAINERS b/MAINTAINERS
index 952fd2a..38dabdf 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9404,6 +9404,12 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
S: Supported
F: drivers/net/wireless/ath/ath10k/
+QUALCOMM EMAC GIGABIT ETHERNET DRIVER
+M: Timur Tabi <timur-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
+L: netdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
+S: Supported
+F: drivers/net/ethernet/qualcomm/emac/
+
QUALCOMM HEXAGON ARCHITECTURE
M: Richard Kuo <rkuo-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
L: linux-hexagon-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
diff --git a/drivers/net/ethernet/qualcomm/Kconfig b/drivers/net/ethernet/qualcomm/Kconfig
index a76e380..9ba568d 100644
--- a/drivers/net/ethernet/qualcomm/Kconfig
+++ b/drivers/net/ethernet/qualcomm/Kconfig
@@ -24,4 +24,16 @@ config QCA7000
To compile this driver as a module, choose M here. The module
will be called qcaspi.
+config QCOM_EMAC
+ tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
+ select CRC32
+ select PHYLIB
+ ---help---
+ This driver supports the Qualcomm Technologies, Inc. Gigabit
+ Ethernet Media Access Controller (EMAC). The controller
+ supports IEEE 802.3-2002, half-duplex mode at 10/100 Mb/s,
+ full-duplex mode at 10/100/1000Mb/s, Wake On LAN (WOL) for
+ low power, Receive-Side Scaling (RSS), and IEEE 1588-2008
+ Precision Clock Synchronization Protocol.
+
endif # NET_VENDOR_QUALCOMM
diff --git a/drivers/net/ethernet/qualcomm/Makefile b/drivers/net/ethernet/qualcomm/Makefile
index 9da2d75..1b3a0ce 100644
--- a/drivers/net/ethernet/qualcomm/Makefile
+++ b/drivers/net/ethernet/qualcomm/Makefile
@@ -4,3 +4,5 @@
obj-$(CONFIG_QCA7000) += qcaspi.o
qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o
+
+obj-$(CONFIG_QCOM_EMAC) += emac/
diff --git a/drivers/net/ethernet/qualcomm/emac/Makefile b/drivers/net/ethernet/qualcomm/emac/Makefile
new file mode 100644
index 0000000..700ee6e
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/Makefile
@@ -0,0 +1,7 @@
+#
+# Makefile for the Qualcomm Technologies, Inc. EMAC Gigabit Ethernet driver
+#
+
+obj-y += qcom-emac.o
+
+qcom-emac-objs := emac.o emac-mac.o emac-phy.o emac-sgmii.o
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-mac.c b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
new file mode 100644
index 0000000..baec5d8
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
@@ -0,0 +1,1530 @@
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC Ethernet Controller MAC layer support
+ */
+
+#include <linux/tcp.h>
+#include <linux/ip.h>
+#include <linux/ipv6.h>
+#include <linux/crc32.h>
+#include <linux/if_vlan.h>
+#include <linux/jiffies.h>
+#include <linux/phy.h>
+#include <linux/of.h>
+#include <net/ip6_checksum.h>
+#include "emac.h"
+#include "emac-sgmii.h"
+
+/* EMAC base register offsets */
+#define EMAC_MAC_CTRL 0x001480
+#define EMAC_WOL_CTRL0 0x0014a0
+#define EMAC_RSS_KEY0 0x0014b0
+#define EMAC_H1TPD_BASE_ADDR_LO 0x0014e0
+#define EMAC_H2TPD_BASE_ADDR_LO 0x0014e4
+#define EMAC_H3TPD_BASE_ADDR_LO 0x0014e8
+#define EMAC_INTER_SRAM_PART9 0x001534
+#define EMAC_DESC_CTRL_0 0x001540
+#define EMAC_DESC_CTRL_1 0x001544
+#define EMAC_DESC_CTRL_2 0x001550
+#define EMAC_DESC_CTRL_10 0x001554
+#define EMAC_DESC_CTRL_12 0x001558
+#define EMAC_DESC_CTRL_13 0x00155c
+#define EMAC_DESC_CTRL_3 0x001560
+#define EMAC_DESC_CTRL_4 0x001564
+#define EMAC_DESC_CTRL_5 0x001568
+#define EMAC_DESC_CTRL_14 0x00156c
+#define EMAC_DESC_CTRL_15 0x001570
+#define EMAC_DESC_CTRL_16 0x001574
+#define EMAC_DESC_CTRL_6 0x001578
+#define EMAC_DESC_CTRL_8 0x001580
+#define EMAC_DESC_CTRL_9 0x001584
+#define EMAC_DESC_CTRL_11 0x001588
+#define EMAC_TXQ_CTRL_0 0x001590
+#define EMAC_TXQ_CTRL_1 0x001594
+#define EMAC_TXQ_CTRL_2 0x001598
+#define EMAC_RXQ_CTRL_0 0x0015a0
+#define EMAC_RXQ_CTRL_1 0x0015a4
+#define EMAC_RXQ_CTRL_2 0x0015a8
+#define EMAC_RXQ_CTRL_3 0x0015ac
+#define EMAC_BASE_CPU_NUMBER 0x0015b8
+#define EMAC_DMA_CTRL 0x0015c0
+#define EMAC_MAILBOX_0 0x0015e0
+#define EMAC_MAILBOX_5 0x0015e4
+#define EMAC_MAILBOX_6 0x0015e8
+#define EMAC_MAILBOX_13 0x0015ec
+#define EMAC_MAILBOX_2 0x0015f4
+#define EMAC_MAILBOX_3 0x0015f8
+#define EMAC_MAILBOX_11 0x00160c
+#define EMAC_AXI_MAST_CTRL 0x001610
+#define EMAC_MAILBOX_12 0x001614
+#define EMAC_MAILBOX_9 0x001618
+#define EMAC_MAILBOX_10 0x00161c
+#define EMAC_ATHR_HEADER_CTRL 0x001620
+#define EMAC_CLK_GATE_CTRL 0x001814
+#define EMAC_MISC_CTRL 0x001990
+#define EMAC_MAILBOX_7 0x0019e0
+#define EMAC_MAILBOX_8 0x0019e4
+#define EMAC_MAILBOX_15 0x001bd4
+#define EMAC_MAILBOX_16 0x001bd8
+
+/* EMAC_MAC_CTRL */
+#define SINGLE_PAUSE_MODE 0x10000000
+#define DEBUG_MODE 0x08000000
+#define BROAD_EN 0x04000000
+#define MULTI_ALL 0x02000000
+#define RX_CHKSUM_EN 0x01000000
+#define HUGE 0x00800000
+#define SPEED(x) (((x) & 0x3) << 20)
+#define SPEED_MASK SPEED(0x3)
+#define SIMR 0x00080000
+#define TPAUSE 0x00010000
+#define PROM_MODE 0x00008000
+#define VLAN_STRIP 0x00004000
+#define PRLEN_BMSK 0x00003c00
+#define PRLEN_SHFT 10
+#define HUGEN 0x00000200
+#define FLCHK 0x00000100
+#define PCRCE 0x00000080
+#define CRCE 0x00000040
+#define FULLD 0x00000020
+#define MAC_LP_EN 0x00000010
+#define RXFC 0x00000008
+#define TXFC 0x00000004
+#define RXEN 0x00000002
+#define TXEN 0x00000001
+
+
+/* EMAC_WOL_CTRL0 */
+#define LK_CHG_PME 0x20
+#define LK_CHG_EN 0x10
+#define MG_FRAME_PME 0x8
+#define MG_FRAME_EN 0x4
+#define WK_FRAME_EN 0x1
+
+/* EMAC_DESC_CTRL_3 */
+#define RFD_RING_SIZE_BMSK 0xfff
+
+/* EMAC_DESC_CTRL_4 */
+#define RX_BUFFER_SIZE_BMSK 0xffff
+
+/* EMAC_DESC_CTRL_6 */
+#define RRD_RING_SIZE_BMSK 0xfff
+
+/* EMAC_DESC_CTRL_9 */
+#define TPD_RING_SIZE_BMSK 0xffff
+
+/* EMAC_TXQ_CTRL_0 */
+#define NUM_TXF_BURST_PREF_BMSK 0xffff0000
+#define NUM_TXF_BURST_PREF_SHFT 16
+#define LS_8023_SP 0x80
+#define TXQ_MODE 0x40
+#define TXQ_EN 0x20
+#define IP_OP_SP 0x10
+#define NUM_TPD_BURST_PREF_BMSK 0xf
+#define NUM_TPD_BURST_PREF_SHFT 0
+
+/* EMAC_TXQ_CTRL_1 */
+#define JUMBO_TASK_OFFLOAD_THRESHOLD_BMSK 0x7ff
+
+/* EMAC_TXQ_CTRL_2 */
+#define TXF_HWM_BMSK 0xfff0000
+#define TXF_LWM_BMSK 0xfff
+
+/* EMAC_RXQ_CTRL_0 */
+#define RXQ_EN BIT(31)
+#define CUT_THRU_EN BIT(30)
+#define RSS_HASH_EN BIT(29)
+#define NUM_RFD_BURST_PREF_BMSK 0x3f00000
+#define NUM_RFD_BURST_PREF_SHFT 20
+#define IDT_TABLE_SIZE_BMSK 0x1ff00
+#define IDT_TABLE_SIZE_SHFT 8
+#define SP_IPV6 0x80
+
+/* EMAC_RXQ_CTRL_1 */
+#define JUMBO_1KAH_BMSK 0xf000
+#define JUMBO_1KAH_SHFT 12
+#define RFD_PREF_LOW_TH 0x10
+#define RFD_PREF_LOW_THRESHOLD_BMSK 0xfc0
+#define RFD_PREF_LOW_THRESHOLD_SHFT 6
+#define RFD_PREF_UP_TH 0x10
+#define RFD_PREF_UP_THRESHOLD_BMSK 0x3f
+#define RFD_PREF_UP_THRESHOLD_SHFT 0
+
+/* EMAC_RXQ_CTRL_2 */
+#define RXF_DOF_THRESFHOLD 0x1a0
+#define RXF_DOF_THRESHOLD_BMSK 0xfff0000
+#define RXF_DOF_THRESHOLD_SHFT 16
+#define RXF_UOF_THRESFHOLD 0xbe
+#define RXF_UOF_THRESHOLD_BMSK 0xfff
+#define RXF_UOF_THRESHOLD_SHFT 0
+
+/* EMAC_RXQ_CTRL_3 */
+#define RXD_TIMER_BMSK 0xffff0000
+#define RXD_THRESHOLD_BMSK 0xfff
+#define RXD_THRESHOLD_SHFT 0
+
+/* EMAC_DMA_CTRL */
+#define DMAW_DLY_CNT_BMSK 0xf0000
+#define DMAW_DLY_CNT_SHFT 16
+#define DMAR_DLY_CNT_BMSK 0xf800
+#define DMAR_DLY_CNT_SHFT 11
+#define DMAR_REQ_PRI 0x400
+#define REGWRBLEN_BMSK 0x380
+#define REGWRBLEN_SHFT 7
+#define REGRDBLEN_BMSK 0x70
+#define REGRDBLEN_SHFT 4
+#define OUT_ORDER_MODE 0x4
+#define ENH_ORDER_MODE 0x2
+#define IN_ORDER_MODE 0x1
+
+/* EMAC_MAILBOX_13 */
+#define RFD3_PROC_IDX_BMSK 0xfff0000
+#define RFD3_PROC_IDX_SHFT 16
+#define RFD3_PROD_IDX_BMSK 0xfff
+#define RFD3_PROD_IDX_SHFT 0
+
+/* EMAC_MAILBOX_2 */
+#define NTPD_CONS_IDX_BMSK 0xffff0000
+#define NTPD_CONS_IDX_SHFT 16
+
+/* EMAC_MAILBOX_3 */
+#define RFD0_CONS_IDX_BMSK 0xfff
+#define RFD0_CONS_IDX_SHFT 0
+
+/* EMAC_MAILBOX_11 */
+#define H3TPD_PROD_IDX_BMSK 0xffff0000
+#define H3TPD_PROD_IDX_SHFT 16
+
+/* EMAC_AXI_MAST_CTRL */
+#define DATA_BYTE_SWAP 0x8
+#define MAX_BOUND 0x2
+#define MAX_BTYPE 0x1
+
+/* EMAC_MAILBOX_12 */
+#define H3TPD_CONS_IDX_BMSK 0xffff0000
+#define H3TPD_CONS_IDX_SHFT 16
+
+/* EMAC_MAILBOX_9 */
+#define H2TPD_PROD_IDX_BMSK 0xffff
+#define H2TPD_PROD_IDX_SHFT 0
+
+/* EMAC_MAILBOX_10 */
+#define H1TPD_CONS_IDX_BMSK 0xffff0000
+#define H1TPD_CONS_IDX_SHFT 16
+#define H2TPD_CONS_IDX_BMSK 0xffff
+#define H2TPD_CONS_IDX_SHFT 0
+
+/* EMAC_ATHR_HEADER_CTRL */
+#define HEADER_CNT_EN 0x2
+#define HEADER_ENABLE 0x1
+
+/* EMAC_MAILBOX_0 */
+#define RFD0_PROC_IDX_BMSK 0xfff0000
+#define RFD0_PROC_IDX_SHFT 16
+#define RFD0_PROD_IDX_BMSK 0xfff
+#define RFD0_PROD_IDX_SHFT 0
+
+/* EMAC_MAILBOX_5 */
+#define RFD1_PROC_IDX_BMSK 0xfff0000
+#define RFD1_PROC_IDX_SHFT 16
+#define RFD1_PROD_IDX_BMSK 0xfff
+#define RFD1_PROD_IDX_SHFT 0
+
+/* EMAC_MISC_CTRL */
+#define RX_UNCPL_INT_EN 0x1
+
+/* EMAC_MAILBOX_7 */
+#define RFD2_CONS_IDX_BMSK 0xfff0000
+#define RFD2_CONS_IDX_SHFT 16
+#define RFD1_CONS_IDX_BMSK 0xfff
+#define RFD1_CONS_IDX_SHFT 0
+
+/* EMAC_MAILBOX_8 */
+#define RFD3_CONS_IDX_BMSK 0xfff
+#define RFD3_CONS_IDX_SHFT 0
+
+/* EMAC_MAILBOX_15 */
+#define NTPD_PROD_IDX_BMSK 0xffff
+#define NTPD_PROD_IDX_SHFT 0
+
+/* EMAC_MAILBOX_16 */
+#define H1TPD_PROD_IDX_BMSK 0xffff
+#define H1TPD_PROD_IDX_SHFT 0
+
+#define RXQ0_RSS_HSTYP_IPV6_TCP_EN 0x20
+#define RXQ0_RSS_HSTYP_IPV6_EN 0x10
+#define RXQ0_RSS_HSTYP_IPV4_TCP_EN 0x8
+#define RXQ0_RSS_HSTYP_IPV4_EN 0x4
+
+/* EMAC_EMAC_WRAPPER_TX_TS_INX */
+#define EMAC_WRAPPER_TX_TS_EMPTY BIT(31)
+#define EMAC_WRAPPER_TX_TS_INX_BMSK 0xffff
+
+struct emac_skb_cb {
+ u32 tpd_idx;
+ unsigned long jiffies;
+};
+
+#define EMAC_SKB_CB(skb) ((struct emac_skb_cb *)(skb)->cb)
+#define EMAC_RSS_IDT_SIZE 256
+#define JUMBO_1KAH 0x4
+#define RXD_TH 0x100
+#define EMAC_TPD_LAST_FRAGMENT 0x80000000
+#define EMAC_TPD_TSTAMP_SAVE 0x80000000
+
+/* EMAC Errors in emac_rrd.word[3] */
+#define EMAC_RRD_L4F BIT(14)
+#define EMAC_RRD_IPF BIT(15)
+#define EMAC_RRD_CRC BIT(21)
+#define EMAC_RRD_FAE BIT(22)
+#define EMAC_RRD_TRN BIT(23)
+#define EMAC_RRD_RNT BIT(24)
+#define EMAC_RRD_INC BIT(25)
+#define EMAC_RRD_FOV BIT(29)
+#define EMAC_RRD_LEN BIT(30)
+
+/* Error bits that will result in a received frame being discarded */
+#define EMAC_RRD_ERROR (EMAC_RRD_IPF | EMAC_RRD_CRC | EMAC_RRD_FAE | \
+ EMAC_RRD_TRN | EMAC_RRD_RNT | EMAC_RRD_INC | \
+ EMAC_RRD_FOV | EMAC_RRD_LEN)
+#define EMAC_RRD_STATS_DW_IDX 3
+
+#define EMAC_RRD(RXQ, SIZE, IDX) ((RXQ)->rrd.v_addr + (SIZE * (IDX)))
+#define EMAC_RFD(RXQ, SIZE, IDX) ((RXQ)->rfd.v_addr + (SIZE * (IDX)))
+#define EMAC_TPD(TXQ, SIZE, IDX) ((TXQ)->tpd.v_addr + (SIZE * (IDX)))
+
+#define GET_RFD_BUFFER(RXQ, IDX) (&((RXQ)->rfd.rfbuff[(IDX)]))
+#define GET_TPD_BUFFER(RTQ, IDX) (&((RTQ)->tpd.tpbuff[(IDX)]))
+
+#define EMAC_TX_POLL_HWTXTSTAMP_THRESHOLD 8
+
+#define ISR_RX_PKT (\
+ RX_PKT_INT0 |\
+ RX_PKT_INT1 |\
+ RX_PKT_INT2 |\
+ RX_PKT_INT3)
+
+#define EMAC_MAC_IRQ_RES "core0"
+
+void emac_mac_multicast_addr_set(struct emac_adapter *adpt, u8 *addr)
+{
+ u32 crc32, bit, reg, mta;
+
+ /* Calculate the CRC of the MAC address */
+ crc32 = ether_crc(ETH_ALEN, addr);
+
+ /* The HASH Table is an array of 2 32-bit registers. It is
+ * treated like an array of 64 bits (BitArray[hash_value]).
+ * Use the upper 6 bits of the above CRC as the hash value.
+ */
+ reg = (crc32 >> 31) & 0x1;
+ bit = (crc32 >> 26) & 0x1F;
+
+ mta = readl(adpt->base + EMAC_HASH_TAB_REG0 + (reg << 2));
+ mta |= BIT(bit);
+ writel(mta, adpt->base + EMAC_HASH_TAB_REG0 + (reg << 2));
+}
+
+void emac_mac_multicast_addr_clear(struct emac_adapter *adpt)
+{
+ writel(0, adpt->base + EMAC_HASH_TAB_REG0);
+ writel(0, adpt->base + EMAC_HASH_TAB_REG1);
+}
+
+/* definitions for RSS */
+#define EMAC_RSS_KEY(_i, _type) \
+ (EMAC_RSS_KEY0 + ((_i) * sizeof(_type)))
+#define EMAC_RSS_TBL(_i, _type) \
+ (EMAC_IDT_TABLE0 + ((_i) * sizeof(_type)))
+
+/* Config MAC modes */
+void emac_mac_mode_config(struct emac_adapter *adpt)
+{
+ struct net_device *netdev = adpt->netdev;
+ u32 mac;
+
+ mac = readl(adpt->base + EMAC_MAC_CTRL);
+ mac &= ~(VLAN_STRIP | PROM_MODE | MULTI_ALL | MAC_LP_EN);
+
+ if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX)
+ mac |= VLAN_STRIP;
+
+ if (netdev->flags & IFF_PROMISC)
+ mac |= PROM_MODE;
+
+ if (netdev->flags & IFF_ALLMULTI)
+ mac |= MULTI_ALL;
+
+ writel(mac, adpt->base + EMAC_MAC_CTRL);
+}
+
+/* Config descriptor rings */
+static void emac_mac_dma_rings_config(struct emac_adapter *adpt)
+{
+ static const unsigned short tpd_q_offset[] = {
+ EMAC_DESC_CTRL_8, EMAC_H1TPD_BASE_ADDR_LO,
+ EMAC_H2TPD_BASE_ADDR_LO, EMAC_H3TPD_BASE_ADDR_LO};
+ static const unsigned short rfd_q_offset[] = {
+ EMAC_DESC_CTRL_2, EMAC_DESC_CTRL_10,
+ EMAC_DESC_CTRL_12, EMAC_DESC_CTRL_13};
+ static const unsigned short rrd_q_offset[] = {
+ EMAC_DESC_CTRL_5, EMAC_DESC_CTRL_14,
+ EMAC_DESC_CTRL_15, EMAC_DESC_CTRL_16};
+
+ /* TPD (Transmit Packet Descriptor) */
+ writel(upper_32_bits(adpt->tx_q.tpd.dma_addr),
+ adpt->base + EMAC_DESC_CTRL_1);
+
+ writel(lower_32_bits(adpt->tx_q.tpd.dma_addr),
+ adpt->base + tpd_q_offset[0]);
+
+ writel(adpt->tx_q.tpd.count & TPD_RING_SIZE_BMSK,
+ adpt->base + EMAC_DESC_CTRL_9);
+
+ /* RFD (Receive Free Descriptor) & RRD (Receive Return Descriptor) */
+ writel(upper_32_bits(adpt->rx_q.rfd.dma_addr),
+ adpt->base + EMAC_DESC_CTRL_0);
+
+ writel(lower_32_bits(adpt->rx_q.rfd.dma_addr),
+ adpt->base + rfd_q_offset[0]);
+ writel(lower_32_bits(adpt->rx_q.rrd.dma_addr),
+ adpt->base + rrd_q_offset[0]);
+
+ writel(adpt->rx_q.rfd.count & RFD_RING_SIZE_BMSK,
+ adpt->base + EMAC_DESC_CTRL_3);
+ writel(adpt->rx_q.rrd.count & RRD_RING_SIZE_BMSK,
+ adpt->base + EMAC_DESC_CTRL_6);
+
+ writel(adpt->rxbuf_size & RX_BUFFER_SIZE_BMSK,
+ adpt->base + EMAC_DESC_CTRL_4);
+
+ writel(0, adpt->base + EMAC_DESC_CTRL_11);
+
+ /* Load all of the base addresses above and ensure that triggering HW to
+ * read ring pointers is flushed
+ */
+ writel(1, adpt->base + EMAC_INTER_SRAM_PART9);
+}
+
+/* Config transmit parameters */
+static void emac_mac_tx_config(struct emac_adapter *adpt)
+{
+ u32 val;
+
+ writel((EMAC_MAX_TX_OFFLOAD_THRESH >> 3) &
+ JUMBO_TASK_OFFLOAD_THRESHOLD_BMSK, adpt->base + EMAC_TXQ_CTRL_1);
+
+ val = (adpt->tpd_burst << NUM_TPD_BURST_PREF_SHFT) &
+ NUM_TPD_BURST_PREF_BMSK;
+
+ val |= TXQ_MODE | LS_8023_SP;
+ val |= (0x0100 << NUM_TXF_BURST_PREF_SHFT) &
+ NUM_TXF_BURST_PREF_BMSK;
+
+ writel(val, adpt->base + EMAC_TXQ_CTRL_0);
+ emac_reg_update32(adpt->base + EMAC_TXQ_CTRL_2,
+ (TXF_HWM_BMSK | TXF_LWM_BMSK), 0);
+}
+
+/* Config receive parameters */
+static void emac_mac_rx_config(struct emac_adapter *adpt)
+{
+ u32 val;
+
+ val = (adpt->rfd_burst << NUM_RFD_BURST_PREF_SHFT) &
+ NUM_RFD_BURST_PREF_BMSK;
+ val |= (SP_IPV6 | CUT_THRU_EN);
+
+ writel(val, adpt->base + EMAC_RXQ_CTRL_0);
+
+ val = readl(adpt->base + EMAC_RXQ_CTRL_1);
+ val &= ~(JUMBO_1KAH_BMSK | RFD_PREF_LOW_THRESHOLD_BMSK |
+ RFD_PREF_UP_THRESHOLD_BMSK);
+ val |= (JUMBO_1KAH << JUMBO_1KAH_SHFT) |
+ (RFD_PREF_LOW_TH << RFD_PREF_LOW_THRESHOLD_SHFT) |
+ (RFD_PREF_UP_TH << RFD_PREF_UP_THRESHOLD_SHFT);
+ writel(val, adpt->base + EMAC_RXQ_CTRL_1);
+
+ val = readl(adpt->base + EMAC_RXQ_CTRL_2);
+ val &= ~(RXF_DOF_THRESHOLD_BMSK | RXF_UOF_THRESHOLD_BMSK);
+ val |= (RXF_DOF_THRESFHOLD << RXF_DOF_THRESHOLD_SHFT) |
+ (RXF_UOF_THRESFHOLD << RXF_UOF_THRESHOLD_SHFT);
+ writel(val, adpt->base + EMAC_RXQ_CTRL_2);
+
+ val = readl(adpt->base + EMAC_RXQ_CTRL_3);
+ val &= ~(RXD_TIMER_BMSK | RXD_THRESHOLD_BMSK);
+ val |= RXD_TH << RXD_THRESHOLD_SHFT;
+ writel(val, adpt->base + EMAC_RXQ_CTRL_3);
+}
+
+/* Config dma */
+static void emac_mac_dma_config(struct emac_adapter *adpt)
+{
+ u32 dma_ctrl = DMAR_REQ_PRI;
+
+ switch (adpt->dma_order) {
+ case emac_dma_ord_in:
+ dma_ctrl |= IN_ORDER_MODE;
+ break;
+ case emac_dma_ord_enh:
+ dma_ctrl |= ENH_ORDER_MODE;
+ break;
+ case emac_dma_ord_out:
+ dma_ctrl |= OUT_ORDER_MODE;
+ break;
+ default:
+ break;
+ }
+
+ dma_ctrl |= (((u32)adpt->dmar_block) << REGRDBLEN_SHFT) &
+ REGRDBLEN_BMSK;
+ dma_ctrl |= (((u32)adpt->dmaw_block) << REGWRBLEN_SHFT) &
+ REGWRBLEN_BMSK;
+ dma_ctrl |= (((u32)adpt->dmar_dly_cnt) << DMAR_DLY_CNT_SHFT) &
+ DMAR_DLY_CNT_BMSK;
+ dma_ctrl |= (((u32)adpt->dmaw_dly_cnt) << DMAW_DLY_CNT_SHFT) &
+ DMAW_DLY_CNT_BMSK;
+
+ /* config DMA and ensure that configuration is flushed to HW */
+ writel(dma_ctrl, adpt->base + EMAC_DMA_CTRL);
+}
+
+/* set MAC address */
+static void emac_set_mac_address(struct emac_adapter *adpt, u8 *addr)
+{
+ u32 sta;
+
+ /* for example: 00-A0-C6-11-22-33
+ * 0<-->C6112233, 1<-->00A0.
+ */
+
+ /* low 32bit word */
+ sta = (((u32)addr[2]) << 24) | (((u32)addr[3]) << 16) |
+ (((u32)addr[4]) << 8) | (((u32)addr[5]));
+ writel(sta, adpt->base + EMAC_MAC_STA_ADDR0);
+
+ /* hight 32bit word */
+ sta = (((u32)addr[0]) << 8) | (u32)addr[1];
+ writel(sta, adpt->base + EMAC_MAC_STA_ADDR1);
+}
+
+void emac_mac_config(struct emac_adapter *adpt)
+{
+ struct net_device *netdev = adpt->netdev;
+ unsigned int max_frame;
+ u32 val;
+
+ emac_set_mac_address(adpt, netdev->dev_addr);
+
+ max_frame = netdev->mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
+ adpt->rxbuf_size = netdev->mtu > EMAC_DEF_RX_BUF_SIZE ?
+ ALIGN(max_frame, 8) : EMAC_DEF_RX_BUF_SIZE;
+
+ emac_mac_dma_rings_config(adpt);
+
+ writel(netdev->mtu + ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN,
+ adpt->base + EMAC_MAX_FRAM_LEN_CTRL);
+
+ emac_mac_tx_config(adpt);
+ emac_mac_rx_config(adpt);
+ emac_mac_dma_config(adpt);
+
+ val = readl(adpt->base + EMAC_AXI_MAST_CTRL);
+ val &= ~(DATA_BYTE_SWAP | MAX_BOUND);
+ val |= MAX_BTYPE;
+ writel(val, adpt->base + EMAC_AXI_MAST_CTRL);
+ writel(0, adpt->base + EMAC_CLK_GATE_CTRL);
+ writel(RX_UNCPL_INT_EN, adpt->base + EMAC_MISC_CTRL);
+}
+
+void emac_mac_reset(struct emac_adapter *adpt)
+{
+ emac_mac_stop(adpt);
+
+ emac_reg_update32(adpt->base + EMAC_DMA_MAS_CTRL, 0, SOFT_RST);
+ usleep_range(100, 150); /* reset may take up to 100usec */
+
+ /* interrupt clear-on-read */
+ emac_reg_update32(adpt->base + EMAC_DMA_MAS_CTRL, 0, INT_RD_CLR_EN);
+}
+
+void emac_mac_start(struct emac_adapter *adpt)
+{
+ struct phy_device *phydev = adpt->phydev;
+ u32 mac, csr1;
+
+ /* enable tx queue */
+ emac_reg_update32(adpt->base + EMAC_TXQ_CTRL_0, 0, TXQ_EN);
+
+ /* enable rx queue */
+ emac_reg_update32(adpt->base + EMAC_RXQ_CTRL_0, 0, RXQ_EN);
+
+ /* enable mac control */
+ mac = readl(adpt->base + EMAC_MAC_CTRL);
+ csr1 = readl(adpt->csr + EMAC_EMAC_WRAPPER_CSR1);
+
+ mac |= TXEN | RXEN; /* enable RX/TX */
+
+ /* We don't have ethtool support yet, so force flow-control mode
+ * to 'full' always.
+ */
+ mac |= TXFC | RXFC;
+
+ /* setup link speed */
+ mac &= ~SPEED_MASK;
+ if (phydev->speed == SPEED_1000) {
+ mac |= SPEED(2);
+ csr1 |= FREQ_MODE;
+ } else {
+ mac |= SPEED(1);
+ csr1 &= ~FREQ_MODE;
+ }
+
+ if (phydev->duplex == DUPLEX_FULL)
+ mac |= FULLD;
+ else
+ mac &= ~FULLD;
+
+ /* other parameters */
+ mac |= (CRCE | PCRCE);
+ mac |= ((adpt->preamble << PRLEN_SHFT) & PRLEN_BMSK);
+ mac |= BROAD_EN;
+ mac |= FLCHK;
+ mac &= ~RX_CHKSUM_EN;
+ mac &= ~(HUGEN | VLAN_STRIP | TPAUSE | SIMR | HUGE | MULTI_ALL |
+ DEBUG_MODE | SINGLE_PAUSE_MODE);
+
+ writel_relaxed(csr1, adpt->csr + EMAC_EMAC_WRAPPER_CSR1);
+
+ writel_relaxed(mac, adpt->base + EMAC_MAC_CTRL);
+
+ /* enable interrupt read clear, low power sleep mode and
+ * the irq moderators
+ */
+
+ writel_relaxed(adpt->irq_mod, adpt->base + EMAC_IRQ_MOD_TIM_INIT);
+ writel_relaxed(INT_RD_CLR_EN | LPW_MODE | IRQ_MODERATOR_EN |
+ IRQ_MODERATOR2_EN, adpt->base + EMAC_DMA_MAS_CTRL);
+
+ emac_mac_mode_config(adpt);
+
+ emac_reg_update32(adpt->base + EMAC_ATHR_HEADER_CTRL,
+ (HEADER_ENABLE | HEADER_CNT_EN), 0);
+
+ emac_reg_update32(adpt->csr + EMAC_EMAC_WRAPPER_CSR2, 0, WOL_EN);
+}
+
+void emac_mac_stop(struct emac_adapter *adpt)
+{
+ emac_reg_update32(adpt->base + EMAC_RXQ_CTRL_0, RXQ_EN, 0);
+ emac_reg_update32(adpt->base + EMAC_TXQ_CTRL_0, TXQ_EN, 0);
+ emac_reg_update32(adpt->base + EMAC_MAC_CTRL, TXEN | RXEN, 0);
+ usleep_range(1000, 1050); /* stopping mac may take upto 1msec */
+}
+
+/* Free all descriptors of given transmit queue */
+static void emac_tx_q_descs_free(struct emac_adapter *adpt)
+{
+ struct emac_tx_queue *tx_q = &adpt->tx_q;
+ unsigned int i;
+ size_t size;
+
+ /* ring already cleared, nothing to do */
+ if (!tx_q->tpd.tpbuff)
+ return;
+
+ for (i = 0; i < tx_q->tpd.count; i++) {
+ struct emac_buffer *tpbuf = GET_TPD_BUFFER(tx_q, i);
+
+ if (tpbuf->dma_addr) {
+ dma_unmap_single(adpt->netdev->dev.parent,
+ tpbuf->dma_addr, tpbuf->length,
+ DMA_TO_DEVICE);
+ tpbuf->dma_addr = 0;
+ }
+ if (tpbuf->skb) {
+ dev_kfree_skb_any(tpbuf->skb);
+ tpbuf->skb = NULL;
+ }
+ }
+
+ size = sizeof(struct emac_buffer) * tx_q->tpd.count;
+ memset(tx_q->tpd.tpbuff, 0, size);
+
+ /* clear the descriptor ring */
+ memset(tx_q->tpd.v_addr, 0, tx_q->tpd.size);
+
+ tx_q->tpd.consume_idx = 0;
+ tx_q->tpd.produce_idx = 0;
+}
+
+/* Free all descriptors of given receive queue */
+static void emac_rx_q_free_descs(struct emac_adapter *adpt)
+{
+ struct device *dev = adpt->netdev->dev.parent;
+ struct emac_rx_queue *rx_q = &adpt->rx_q;
+ unsigned int i;
+ size_t size;
+
+ /* ring already cleared, nothing to do */
+ if (!rx_q->rfd.rfbuff)
+ return;
+
+ for (i = 0; i < rx_q->rfd.count; i++) {
+ struct emac_buffer *rfbuf = GET_RFD_BUFFER(rx_q, i);
+
+ if (rfbuf->dma_addr) {
+ dma_unmap_single(dev, rfbuf->dma_addr, rfbuf->length,
+ DMA_FROM_DEVICE);
+ rfbuf->dma_addr = 0;
+ }
+ if (rfbuf->skb) {
+ dev_kfree_skb(rfbuf->skb);
+ rfbuf->skb = NULL;
+ }
+ }
+
+ size = sizeof(struct emac_buffer) * rx_q->rfd.count;
+ memset(rx_q->rfd.rfbuff, 0, size);
+
+ /* clear the descriptor rings */
+ memset(rx_q->rrd.v_addr, 0, rx_q->rrd.size);
+ rx_q->rrd.produce_idx = 0;
+ rx_q->rrd.consume_idx = 0;
+
+ memset(rx_q->rfd.v_addr, 0, rx_q->rfd.size);
+ rx_q->rfd.produce_idx = 0;
+ rx_q->rfd.consume_idx = 0;
+}
+
+/* Free all buffers associated with given transmit queue */
+static void emac_tx_q_bufs_free(struct emac_adapter *adpt)
+{
+ struct emac_tx_queue *tx_q = &adpt->tx_q;
+
+ emac_tx_q_descs_free(adpt);
+
+ kfree(tx_q->tpd.tpbuff);
+ tx_q->tpd.tpbuff = NULL;
+ tx_q->tpd.v_addr = NULL;
+ tx_q->tpd.dma_addr = 0;
+ tx_q->tpd.size = 0;
+}
+
+/* Allocate TX descriptor ring for the given transmit queue */
+static int emac_tx_q_desc_alloc(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q)
+{
+ struct emac_ring_header *ring_header = &adpt->ring_header;
+ size_t size;
+
+ size = sizeof(struct emac_buffer) * tx_q->tpd.count;
+ tx_q->tpd.tpbuff = kzalloc(size, GFP_KERNEL);
+ if (!tx_q->tpd.tpbuff)
+ return -ENOMEM;
+
+ tx_q->tpd.size = tx_q->tpd.count * (adpt->tpd_size * 4);
+ tx_q->tpd.dma_addr = ring_header->dma_addr + ring_header->used;
+ tx_q->tpd.v_addr = ring_header->v_addr + ring_header->used;
+ ring_header->used += ALIGN(tx_q->tpd.size, 8);
+ tx_q->tpd.produce_idx = 0;
+ tx_q->tpd.consume_idx = 0;
+
+ return 0;
+}
+
+/* Free all buffers associated with given transmit queue */
+static void emac_rx_q_bufs_free(struct emac_adapter *adpt)
+{
+ struct emac_rx_queue *rx_q = &adpt->rx_q;
+
+ emac_rx_q_free_descs(adpt);
+
+ kfree(rx_q->rfd.rfbuff);
+ rx_q->rfd.rfbuff = NULL;
+
+ rx_q->rfd.v_addr = NULL;
+ rx_q->rfd.dma_addr = 0;
+ rx_q->rfd.size = 0;
+
+ rx_q->rrd.v_addr = NULL;
+ rx_q->rrd.dma_addr = 0;
+ rx_q->rrd.size = 0;
+}
+
+/* Allocate RX descriptor rings for the given receive queue */
+static int emac_rx_descs_alloc(struct emac_adapter *adpt)
+{
+ struct emac_ring_header *ring_header = &adpt->ring_header;
+ struct emac_rx_queue *rx_q = &adpt->rx_q;
+ size_t size;
+
+ size = sizeof(struct emac_buffer) * rx_q->rfd.count;
+ rx_q->rfd.rfbuff = kzalloc(size, GFP_KERNEL);
+ if (!rx_q->rfd.rfbuff)
+ return -ENOMEM;
+
+ rx_q->rrd.size = rx_q->rrd.count * (adpt->rrd_size * 4);
+ rx_q->rfd.size = rx_q->rfd.count * (adpt->rfd_size * 4);
+
+ rx_q->rrd.dma_addr = ring_header->dma_addr + ring_header->used;
+ rx_q->rrd.v_addr = ring_header->v_addr + ring_header->used;
+ ring_header->used += ALIGN(rx_q->rrd.size, 8);
+
+ rx_q->rfd.dma_addr = ring_header->dma_addr + ring_header->used;
+ rx_q->rfd.v_addr = ring_header->v_addr + ring_header->used;
+ ring_header->used += ALIGN(rx_q->rfd.size, 8);
+
+ rx_q->rrd.produce_idx = 0;
+ rx_q->rrd.consume_idx = 0;
+
+ rx_q->rfd.produce_idx = 0;
+ rx_q->rfd.consume_idx = 0;
+
+ return 0;
+}
+
+/* Allocate all TX and RX descriptor rings */
+int emac_mac_rx_tx_rings_alloc_all(struct emac_adapter *adpt)
+{
+ struct emac_ring_header *ring_header = &adpt->ring_header;
+ struct device *dev = adpt->netdev->dev.parent;
+ unsigned int num_tx_descs = adpt->tx_desc_cnt;
+ unsigned int num_rx_descs = adpt->rx_desc_cnt;
+ int ret;
+
+ adpt->tx_q.tpd.count = adpt->tx_desc_cnt;
+
+ adpt->rx_q.rrd.count = adpt->rx_desc_cnt;
+ adpt->rx_q.rfd.count = adpt->rx_desc_cnt;
+
+ /* Ring DMA buffer. Each ring may need up to 8 bytes for alignment,
+ * hence the additional padding bytes are allocated.
+ */
+ ring_header->size = num_tx_descs * (adpt->tpd_size * 4) +
+ num_rx_descs * (adpt->rfd_size * 4) +
+ num_rx_descs * (adpt->rrd_size * 4) +
+ 8 + 2 * 8; /* 8 byte per one Tx and two Rx rings */
+
+ ring_header->used = 0;
+ ring_header->v_addr = dma_zalloc_coherent(dev, ring_header->size,
+ &ring_header->dma_addr,
+ GFP_KERNEL);
+ if (!ring_header->v_addr)
+ return -ENOMEM;
+
+ ring_header->used = ALIGN(ring_header->dma_addr, 8) -
+ ring_header->dma_addr;
+
+ ret = emac_tx_q_desc_alloc(adpt, &adpt->tx_q);
+ if (ret) {
+ netdev_err(adpt->netdev, "error: Tx Queue alloc failed\n");
+ goto err_alloc_tx;
+ }
+
+ ret = emac_rx_descs_alloc(adpt);
+ if (ret) {
+ netdev_err(adpt->netdev, "error: Rx Queue alloc failed\n");
+ goto err_alloc_rx;
+ }
+
+ return 0;
+
+err_alloc_rx:
+ emac_tx_q_bufs_free(adpt);
+err_alloc_tx:
+ dma_free_coherent(dev, ring_header->size,
+ ring_header->v_addr, ring_header->dma_addr);
+
+ ring_header->v_addr = NULL;
+ ring_header->dma_addr = 0;
+ ring_header->size = 0;
+ ring_header->used = 0;
+
+ return ret;
+}
+
+/* Free all TX and RX descriptor rings */
+void emac_mac_rx_tx_rings_free_all(struct emac_adapter *adpt)
+{
+ struct emac_ring_header *ring_header = &adpt->ring_header;
+ struct device *dev = adpt->netdev->dev.parent;
+
+ emac_tx_q_bufs_free(adpt);
+ emac_rx_q_bufs_free(adpt);
+
+ dma_free_coherent(dev, ring_header->size,
+ ring_header->v_addr, ring_header->dma_addr);
+
+ ring_header->v_addr = NULL;
+ ring_header->dma_addr = 0;
+ ring_header->size = 0;
+ ring_header->used = 0;
+}
+
+/* Initialize descriptor rings */
+static void emac_mac_rx_tx_ring_reset_all(struct emac_adapter *adpt)
+{
+ unsigned int i;
+
+ adpt->tx_q.tpd.produce_idx = 0;
+ adpt->tx_q.tpd.consume_idx = 0;
+ for (i = 0; i < adpt->tx_q.tpd.count; i++)
+ adpt->tx_q.tpd.tpbuff[i].dma_addr = 0;
+
+ adpt->rx_q.rrd.produce_idx = 0;
+ adpt->rx_q.rrd.consume_idx = 0;
+ adpt->rx_q.rfd.produce_idx = 0;
+ adpt->rx_q.rfd.consume_idx = 0;
+ for (i = 0; i < adpt->rx_q.rfd.count; i++)
+ adpt->rx_q.rfd.rfbuff[i].dma_addr = 0;
+}
+
+/* Produce new receive free descriptor */
+static void emac_mac_rx_rfd_create(struct emac_adapter *adpt,
+ struct emac_rx_queue *rx_q,
+ dma_addr_t addr)
+{
+ u32 *hw_rfd = EMAC_RFD(rx_q, adpt->rfd_size, rx_q->rfd.produce_idx);
+
+ *(hw_rfd++) = lower_32_bits(addr);
+ *hw_rfd = upper_32_bits(addr);
+
+ if (++rx_q->rfd.produce_idx == rx_q->rfd.count)
+ rx_q->rfd.produce_idx = 0;
+}
+
+/* Fill up receive queue's RFD with preallocated receive buffers */
+static void emac_mac_rx_descs_refill(struct emac_adapter *adpt,
+ struct emac_rx_queue *rx_q)
+{
+ struct emac_buffer *curr_rxbuf;
+ struct emac_buffer *next_rxbuf;
+ unsigned int count = 0;
+ u32 next_produce_idx;
+
+ next_produce_idx = rx_q->rfd.produce_idx + 1;
+ if (next_produce_idx == rx_q->rfd.count)
+ next_produce_idx = 0;
+
+ curr_rxbuf = GET_RFD_BUFFER(rx_q, rx_q->rfd.produce_idx);
+ next_rxbuf = GET_RFD_BUFFER(rx_q, next_produce_idx);
+
+ /* this always has a blank rx_buffer*/
+ while (!next_rxbuf->dma_addr) {
+ struct sk_buff *skb;
+ int ret;
+
+ skb = netdev_alloc_skb_ip_align(adpt->netdev, adpt->rxbuf_size);
+ if (!skb)
+ break;
+
+ curr_rxbuf->dma_addr =
+ dma_map_single(adpt->netdev->dev.parent, skb->data,
+ curr_rxbuf->length, DMA_FROM_DEVICE);
+ ret = dma_mapping_error(adpt->netdev->dev.parent,
+ curr_rxbuf->dma_addr);
+ if (ret) {
+ dev_kfree_skb(skb);
+ break;
+ }
+ curr_rxbuf->skb = skb;
+ curr_rxbuf->length = adpt->rxbuf_size;
+
+ emac_mac_rx_rfd_create(adpt, rx_q, curr_rxbuf->dma_addr);
+ next_produce_idx = rx_q->rfd.produce_idx + 1;
+ if (next_produce_idx == rx_q->rfd.count)
+ next_produce_idx = 0;
+
+ curr_rxbuf = GET_RFD_BUFFER(rx_q, rx_q->rfd.produce_idx);
+ next_rxbuf = GET_RFD_BUFFER(rx_q, next_produce_idx);
+ count++;
+ }
+
+ if (count) {
+ u32 prod_idx = (rx_q->rfd.produce_idx << rx_q->produce_shift) &
+ rx_q->produce_mask;
+ emac_reg_update32(adpt->base + rx_q->produce_reg,
+ rx_q->produce_mask, prod_idx);
+ }
+}
+
+static void emac_adjust_link(struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ struct phy_device *phydev = netdev->phydev;
+
+ if (phydev->link)
+ emac_mac_start(adpt);
+ else
+ emac_mac_stop(adpt);
+
+ phy_print_status(phydev);
+}
+
+/* Bringup the interface/HW */
+int emac_mac_up(struct emac_adapter *adpt)
+{
+ struct net_device *netdev = adpt->netdev;
+ struct emac_irq *irq = &adpt->irq;
+ int ret;
+
+ emac_mac_rx_tx_ring_reset_all(adpt);
+ emac_mac_config(adpt);
+
+ ret = request_irq(irq->irq, emac_isr, 0, EMAC_MAC_IRQ_RES, irq);
+ if (ret) {
+ netdev_err(adpt->netdev, "could not request %s irq\n",
+ EMAC_MAC_IRQ_RES);
+ return ret;
+ }
+
+ emac_mac_rx_descs_refill(adpt, &adpt->rx_q);
+
+ ret = phy_connect_direct(netdev, adpt->phydev, emac_adjust_link,
+ PHY_INTERFACE_MODE_SGMII);
+ if (ret) {
+ netdev_err(adpt->netdev, "could not connect phy\n");
+ free_irq(irq->irq, irq);
+ return ret;
+ }
+
+ /* enable mac irq */
+ writel((u32)~DIS_INT, adpt->base + EMAC_INT_STATUS);
+ writel(adpt->irq.mask, adpt->base + EMAC_INT_MASK);
+
+ adpt->phydev->irq = PHY_IGNORE_INTERRUPT;
+ phy_start(adpt->phydev);
+
+ napi_enable(&adpt->rx_q.napi);
+ netif_start_queue(netdev);
+
+ return 0;
+}
+
+/* Bring down the interface/HW */
+void emac_mac_down(struct emac_adapter *adpt)
+{
+ struct net_device *netdev = adpt->netdev;
+
+ netif_stop_queue(netdev);
+ napi_disable(&adpt->rx_q.napi);
+
+ phy_stop(adpt->phydev);
+ phy_disconnect(adpt->phydev);
+
+ /* disable mac irq */
+ writel(DIS_INT, adpt->base + EMAC_INT_STATUS);
+ writel(0, adpt->base + EMAC_INT_MASK);
+ synchronize_irq(adpt->irq.irq);
+ free_irq(adpt->irq.irq, &adpt->irq);
+
+ emac_mac_reset(adpt);
+
+ emac_tx_q_descs_free(adpt);
+ netdev_reset_queue(adpt->netdev);
+ emac_rx_q_free_descs(adpt);
+}
+
+/* Consume next received packet descriptor */
+static bool emac_rx_process_rrd(struct emac_adapter *adpt,
+ struct emac_rx_queue *rx_q,
+ struct emac_rrd *rrd)
+{
+ u32 *hw_rrd = EMAC_RRD(rx_q, adpt->rrd_size, rx_q->rrd.consume_idx);
+
+ rrd->word[3] = *(hw_rrd + 3);
+
+ if (!RRD_UPDT(rrd))
+ return false;
+
+ rrd->word[4] = 0;
+ rrd->word[5] = 0;
+
+ rrd->word[0] = *(hw_rrd++);
+ rrd->word[1] = *(hw_rrd++);
+ rrd->word[2] = *(hw_rrd++);
+
+ if (unlikely(RRD_NOR(rrd) != 1)) {
+ netdev_err(adpt->netdev,
+ "error: multi-RFD not support yet! nor:%lu\n",
+ RRD_NOR(rrd));
+ }
+
+ /* mark rrd as processed */
+ RRD_UPDT_SET(rrd, 0);
+ *hw_rrd = rrd->word[3];
+
+ if (++rx_q->rrd.consume_idx == rx_q->rrd.count)
+ rx_q->rrd.consume_idx = 0;
+
+ return true;
+}
+
+/* Produce new transmit descriptor */
+static bool emac_tx_tpd_create(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q, struct emac_tpd *tpd)
+{
+ u32 *hw_tpd;
+
+ tx_q->tpd.last_produce_idx = tx_q->tpd.produce_idx;
+ hw_tpd = EMAC_TPD(tx_q, adpt->tpd_size, tx_q->tpd.produce_idx);
+
+ if (++tx_q->tpd.produce_idx == tx_q->tpd.count)
+ tx_q->tpd.produce_idx = 0;
+
+ *(hw_tpd++) = tpd->word[0];
+ *(hw_tpd++) = tpd->word[1];
+ *(hw_tpd++) = tpd->word[2];
+ *hw_tpd = tpd->word[3];
+
+ return true;
+}
+
+/* Mark the last transmit descriptor as such (for the transmit packet) */
+static void emac_tx_tpd_mark_last(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q)
+{
+ u32 *hw_tpd =
+ EMAC_TPD(tx_q, adpt->tpd_size, tx_q->tpd.last_produce_idx);
+ u32 tmp_tpd;
+
+ tmp_tpd = *(hw_tpd + 1);
+ tmp_tpd |= EMAC_TPD_LAST_FRAGMENT;
+ *(hw_tpd + 1) = tmp_tpd;
+}
+
+static void emac_rx_rfd_clean(struct emac_rx_queue *rx_q, struct emac_rrd *rrd)
+{
+ struct emac_buffer *rfbuf = rx_q->rfd.rfbuff;
+ u32 consume_idx = RRD_SI(rrd);
+ unsigned int i;
+
+ for (i = 0; i < RRD_NOR(rrd); i++) {
+ rfbuf[consume_idx].skb = NULL;
+ if (++consume_idx == rx_q->rfd.count)
+ consume_idx = 0;
+ }
+
+ rx_q->rfd.consume_idx = consume_idx;
+ rx_q->rfd.process_idx = consume_idx;
+}
+
+/* Push the received skb to upper layers */
+static void emac_receive_skb(struct emac_rx_queue *rx_q,
+ struct sk_buff *skb,
+ u16 vlan_tag, bool vlan_flag)
+{
+ if (vlan_flag) {
+ u16 vlan;
+
+ EMAC_TAG_TO_VLAN(vlan_tag, vlan);
+ __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan);
+ }
+
+ napi_gro_receive(&rx_q->napi, skb);
+}
+
+/* Process receive event */
+void emac_mac_rx_process(struct emac_adapter *adpt, struct emac_rx_queue *rx_q,
+ int *num_pkts, int max_pkts)
+{
+ u32 proc_idx, hw_consume_idx, num_consume_pkts;
+ struct net_device *netdev = adpt->netdev;
+ struct emac_buffer *rfbuf;
+ unsigned int count = 0;
+ struct emac_rrd rrd;
+ struct sk_buff *skb;
+ u32 reg;
+
+ reg = readl_relaxed(adpt->base + rx_q->consume_reg);
+
+ hw_consume_idx = (reg & rx_q->consume_mask) >> rx_q->consume_shift;
+ num_consume_pkts = (hw_consume_idx >= rx_q->rrd.consume_idx) ?
+ (hw_consume_idx - rx_q->rrd.consume_idx) :
+ (hw_consume_idx + rx_q->rrd.count - rx_q->rrd.consume_idx);
+
+ do {
+ if (!num_consume_pkts)
+ break;
+
+ if (!emac_rx_process_rrd(adpt, rx_q, &rrd))
+ break;
+
+ if (likely(RRD_NOR(&rrd) == 1)) {
+ /* good receive */
+ rfbuf = GET_RFD_BUFFER(rx_q, RRD_SI(&rrd));
+ dma_unmap_single(adpt->netdev->dev.parent,
+ rfbuf->dma_addr, rfbuf->length,
+ DMA_FROM_DEVICE);
+ rfbuf->dma_addr = 0;
+ skb = rfbuf->skb;
+ } else {
+ netdev_err(adpt->netdev,
+ "error: multi-RFD not support yet!\n");
+ break;
+ }
+ emac_rx_rfd_clean(rx_q, &rrd);
+ num_consume_pkts--;
+ count++;
+
+ /* Due to a HW issue in L4 check sum detection (UDP/TCP frags
+ * with DF set are marked as error), drop packets based on the
+ * error mask rather than the summary bit (ignoring L4F errors)
+ */
+ if (rrd.word[EMAC_RRD_STATS_DW_IDX] & EMAC_RRD_ERROR) {
+ netif_dbg(adpt, rx_status, adpt->netdev,
+ "Drop error packet[RRD: 0x%x:0x%x:0x%x:0x%x]\n",
+ rrd.word[0], rrd.word[1],
+ rrd.word[2], rrd.word[3]);
+
+ dev_kfree_skb(skb);
+ continue;
+ }
+
+ skb_put(skb, RRD_PKT_SIZE(&rrd) - ETH_FCS_LEN);
+ skb->dev = netdev;
+ skb->protocol = eth_type_trans(skb, skb->dev);
+ if (netdev->features & NETIF_F_RXCSUM)
+ skb->ip_summed = RRD_L4F(&rrd) ?
+ CHECKSUM_NONE : CHECKSUM_UNNECESSARY;
+ else
+ skb_checksum_none_assert(skb);
+
+ emac_receive_skb(rx_q, skb, (u16)RRD_CVALN_TAG(&rrd),
+ (bool)RRD_CVTAG(&rrd));
+
+ netdev->last_rx = jiffies;
+ (*num_pkts)++;
+ } while (*num_pkts < max_pkts);
+
+ if (count) {
+ proc_idx = (rx_q->rfd.process_idx << rx_q->process_shft) &
+ rx_q->process_mask;
+ emac_reg_update32(adpt->base + rx_q->process_reg,
+ rx_q->process_mask, proc_idx);
+ emac_mac_rx_descs_refill(adpt, rx_q);
+ }
+}
+
+/* get the number of free transmit descriptors */
+static unsigned int emac_tpd_num_free_descs(struct emac_tx_queue *tx_q)
+{
+ u32 produce_idx = tx_q->tpd.produce_idx;
+ u32 consume_idx = tx_q->tpd.consume_idx;
+
+ return (consume_idx > produce_idx) ?
+ (consume_idx - produce_idx - 1) :
+ (tx_q->tpd.count + consume_idx - produce_idx - 1);
+}
+
+/* Process transmit event */
+void emac_mac_tx_process(struct emac_adapter *adpt, struct emac_tx_queue *tx_q)
+{
+ u32 reg = readl_relaxed(adpt->base + tx_q->consume_reg);
+ u32 hw_consume_idx, pkts_compl = 0, bytes_compl = 0;
+ struct emac_buffer *tpbuf;
+
+ hw_consume_idx = (reg & tx_q->consume_mask) >> tx_q->consume_shift;
+
+ while (tx_q->tpd.consume_idx != hw_consume_idx) {
+ tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.consume_idx);
+ if (tpbuf->dma_addr) {
+ dma_unmap_single(adpt->netdev->dev.parent,
+ tpbuf->dma_addr, tpbuf->length,
+ DMA_TO_DEVICE);
+ tpbuf->dma_addr = 0;
+ }
+
+ if (tpbuf->skb) {
+ pkts_compl++;
+ bytes_compl += tpbuf->skb->len;
+ dev_kfree_skb_irq(tpbuf->skb);
+ tpbuf->skb = NULL;
+ }
+
+ if (++tx_q->tpd.consume_idx == tx_q->tpd.count)
+ tx_q->tpd.consume_idx = 0;
+ }
+
+ netdev_completed_queue(adpt->netdev, pkts_compl, bytes_compl);
+
+ if (netif_queue_stopped(adpt->netdev))
+ if (emac_tpd_num_free_descs(tx_q) > (MAX_SKB_FRAGS + 1))
+ netif_wake_queue(adpt->netdev);
+}
+
+/* Initialize all queue data structures */
+void emac_mac_rx_tx_ring_init_all(struct platform_device *pdev,
+ struct emac_adapter *adpt)
+{
+ adpt->rx_q.netdev = adpt->netdev;
+
+ adpt->rx_q.produce_reg = EMAC_MAILBOX_0;
+ adpt->rx_q.produce_mask = RFD0_PROD_IDX_BMSK;
+ adpt->rx_q.produce_shift = RFD0_PROD_IDX_SHFT;
+
+ adpt->rx_q.process_reg = EMAC_MAILBOX_0;
+ adpt->rx_q.process_mask = RFD0_PROC_IDX_BMSK;
+ adpt->rx_q.process_shft = RFD0_PROC_IDX_SHFT;
+
+ adpt->rx_q.consume_reg = EMAC_MAILBOX_3;
+ adpt->rx_q.consume_mask = RFD0_CONS_IDX_BMSK;
+ adpt->rx_q.consume_shift = RFD0_CONS_IDX_SHFT;
+
+ adpt->rx_q.irq = &adpt->irq;
+ adpt->rx_q.intr = adpt->irq.mask & ISR_RX_PKT;
+
+ adpt->tx_q.produce_reg = EMAC_MAILBOX_15;
+ adpt->tx_q.produce_mask = NTPD_PROD_IDX_BMSK;
+ adpt->tx_q.produce_shift = NTPD_PROD_IDX_SHFT;
+
+ adpt->tx_q.consume_reg = EMAC_MAILBOX_2;
+ adpt->tx_q.consume_mask = NTPD_CONS_IDX_BMSK;
+ adpt->tx_q.consume_shift = NTPD_CONS_IDX_SHFT;
+}
+
+/* Fill up transmit descriptors with TSO and Checksum offload information */
+static int emac_tso_csum(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q,
+ struct sk_buff *skb,
+ struct emac_tpd *tpd)
+{
+ unsigned int hdr_len;
+ int ret;
+
+ if (skb_is_gso(skb)) {
+ if (skb_header_cloned(skb)) {
+ ret = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+ if (unlikely(ret))
+ return ret;
+ }
+
+ if (skb->protocol == htons(ETH_P_IP)) {
+ u32 pkt_len = ((unsigned char *)ip_hdr(skb) - skb->data)
+ + ntohs(ip_hdr(skb)->tot_len);
+ if (skb->len > pkt_len)
+ pskb_trim(skb, pkt_len);
+ }
+
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ if (unlikely(skb->len == hdr_len)) {
+ /* we only need to do csum */
+ netif_warn(adpt, tx_err, adpt->netdev,
+ "tso not needed for packet with 0 data\n");
+ goto do_csum;
+ }
+
+ if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV4) {
+ ip_hdr(skb)->check = 0;
+ tcp_hdr(skb)->check =
+ ~csum_tcpudp_magic(ip_hdr(skb)->saddr,
+ ip_hdr(skb)->daddr,
+ 0, IPPROTO_TCP, 0);
+ TPD_IPV4_SET(tpd, 1);
+ }
+
+ if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6) {
+ /* ipv6 tso need an extra tpd */
+ struct emac_tpd extra_tpd;
+
+ memset(tpd, 0, sizeof(*tpd));
+ memset(&extra_tpd, 0, sizeof(extra_tpd));
+
+ ipv6_hdr(skb)->payload_len = 0;
+ tcp_hdr(skb)->check =
+ ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
+ &ipv6_hdr(skb)->daddr,
+ 0, IPPROTO_TCP, 0);
+ TPD_PKT_LEN_SET(&extra_tpd, skb->len);
+ TPD_LSO_SET(&extra_tpd, 1);
+ TPD_LSOV_SET(&extra_tpd, 1);
+ emac_tx_tpd_create(adpt, tx_q, &extra_tpd);
+ TPD_LSOV_SET(tpd, 1);
+ }
+
+ TPD_LSO_SET(tpd, 1);
+ TPD_TCPHDR_OFFSET_SET(tpd, skb_transport_offset(skb));
+ TPD_MSS_SET(tpd, skb_shinfo(skb)->gso_size);
+ return 0;
+ }
+
+do_csum:
+ if (likely(skb->ip_summed == CHECKSUM_PARTIAL)) {
+ unsigned int css, cso;
+
+ cso = skb_transport_offset(skb);
+ if (unlikely(cso & 0x1)) {
+ netdev_err(adpt->netdev,
+ "error: payload offset should be even\n");
+ return -EINVAL;
+ }
+ css = cso + skb->csum_offset;
+
+ TPD_PAYLOAD_OFFSET_SET(tpd, cso >> 1);
+ TPD_CXSUM_OFFSET_SET(tpd, css >> 1);
+ TPD_CSX_SET(tpd, 1);
+ }
+
+ return 0;
+}
+
+/* Fill up transmit descriptors */
+static void emac_tx_fill_tpd(struct emac_adapter *adpt,
+ struct emac_tx_queue *tx_q, struct sk_buff *skb,
+ struct emac_tpd *tpd)
+{
+ unsigned int nr_frags = skb_shinfo(skb)->nr_frags;
+ unsigned int first = tx_q->tpd.produce_idx;
+ unsigned int len = skb_headlen(skb);
+ struct emac_buffer *tpbuf = NULL;
+ unsigned int mapped_len = 0;
+ unsigned int i;
+ int count = 0;
+ int ret;
+
+ /* if Large Segment Offload is (in TCP Segmentation Offload struct) */
+ if (TPD_LSO(tpd)) {
+ mapped_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+
+ tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.produce_idx);
+ tpbuf->length = mapped_len;
+ tpbuf->dma_addr = dma_map_single(adpt->netdev->dev.parent,
+ skb->data, tpbuf->length,
+ DMA_TO_DEVICE);
+ ret = dma_mapping_error(adpt->netdev->dev.parent,
+ tpbuf->dma_addr);
+ if (ret)
+ goto error;
+
+ TPD_BUFFER_ADDR_L_SET(tpd, lower_32_bits(tpbuf->dma_addr));
+ TPD_BUFFER_ADDR_H_SET(tpd, upper_32_bits(tpbuf->dma_addr));
+ TPD_BUF_LEN_SET(tpd, tpbuf->length);
+ emac_tx_tpd_create(adpt, tx_q, tpd);
+ count++;
+ }
+
+ if (mapped_len < len) {
+ tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.produce_idx);
+ tpbuf->length = len - mapped_len;
+ tpbuf->dma_addr = dma_map_single(adpt->netdev->dev.parent,
+ skb->data + mapped_len,
+ tpbuf->length, DMA_TO_DEVICE);
+ ret = dma_mapping_error(adpt->netdev->dev.parent,
+ tpbuf->dma_addr);
+ if (ret)
+ goto error;
+
+ TPD_BUFFER_ADDR_L_SET(tpd, lower_32_bits(tpbuf->dma_addr));
+ TPD_BUFFER_ADDR_H_SET(tpd, upper_32_bits(tpbuf->dma_addr));
+ TPD_BUF_LEN_SET(tpd, tpbuf->length);
+ emac_tx_tpd_create(adpt, tx_q, tpd);
+ count++;
+ }
+
+ for (i = 0; i < nr_frags; i++) {
+ struct skb_frag_struct *frag;
+
+ frag = &skb_shinfo(skb)->frags[i];
+
+ tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.produce_idx);
+ tpbuf->length = frag->size;
+ tpbuf->dma_addr = dma_map_page(adpt->netdev->dev.parent,
+ frag->page.p, frag->page_offset,
+ tpbuf->length, DMA_TO_DEVICE);
+ ret = dma_mapping_error(adpt->netdev->dev.parent,
+ tpbuf->dma_addr);
+ if (ret)
+ goto error;
+
+ TPD_BUFFER_ADDR_L_SET(tpd, lower_32_bits(tpbuf->dma_addr));
+ TPD_BUFFER_ADDR_H_SET(tpd, upper_32_bits(tpbuf->dma_addr));
+ TPD_BUF_LEN_SET(tpd, tpbuf->length);
+ emac_tx_tpd_create(adpt, tx_q, tpd);
+ count++;
+ }
+
+ /* The last tpd */
+ wmb();
+ emac_tx_tpd_mark_last(adpt, tx_q);
+
+ /* The last buffer info contain the skb address,
+ * so it will be freed after unmap
+ */
+ tpbuf->skb = skb;
+
+ return;
+
+error:
+ /* One of the memory mappings failed, so undo everything */
+ tx_q->tpd.produce_idx = first;
+
+ while (count--) {
+ tpbuf = GET_TPD_BUFFER(tx_q, first);
+ dma_unmap_page(adpt->netdev->dev.parent, tpbuf->dma_addr,
+ tpbuf->length, DMA_TO_DEVICE);
+ tpbuf->dma_addr = 0;
+ tpbuf->length = 0;
+
+ if (++first == tx_q->tpd.count)
+ first = 0;
+ }
+
+ dev_kfree_skb(skb);
+}
+
+/* Transmit the packet using specified transmit queue */
+int emac_mac_tx_buf_send(struct emac_adapter *adpt, struct emac_tx_queue *tx_q,
+ struct sk_buff *skb)
+{
+ struct emac_tpd tpd;
+ u32 prod_idx;
+
+ memset(&tpd, 0, sizeof(tpd));
+
+ if (emac_tso_csum(adpt, tx_q, skb, &tpd) != 0) {
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ if (skb_vlan_tag_present(skb)) {
+ u16 tag;
+
+ EMAC_VLAN_TO_TAG(skb_vlan_tag_get(skb), tag);
+ TPD_CVLAN_TAG_SET(&tpd, tag);
+ TPD_INSTC_SET(&tpd, 1);
+ }
+
+ if (skb_network_offset(skb) != ETH_HLEN)
+ TPD_TYP_SET(&tpd, 1);
+
+ emac_tx_fill_tpd(adpt, tx_q, skb, &tpd);
+
+ netdev_sent_queue(adpt->netdev, skb->len);
+
+ /* Make sure the are enough free descriptors to hold one
+ * maximum-sized SKB. We need one desc for each fragment,
+ * one for the checksum (emac_tso_csum), one for TSO, and
+ * and one for the SKB header.
+ */
+ if (emac_tpd_num_free_descs(tx_q) < (MAX_SKB_FRAGS + 3))
+ netif_stop_queue(adpt->netdev);
+
+ /* update produce idx */
+ prod_idx = (tx_q->tpd.produce_idx << tx_q->produce_shift) &
+ tx_q->produce_mask;
+ emac_reg_update32(adpt->base + tx_q->produce_reg,
+ tx_q->produce_mask, prod_idx);
+
+ return NETDEV_TX_OK;
+}
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-mac.h b/drivers/net/ethernet/qualcomm/emac/emac-mac.h
new file mode 100644
index 0000000..0d3499f
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-mac.h
@@ -0,0 +1,248 @@
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* EMAC DMA HW engine uses three rings:
+ * Tx:
+ * TPD: Transmit Packet Descriptor ring.
+ * Rx:
+ * RFD: Receive Free Descriptor ring.
+ * Ring of descriptors with empty buffers to be filled by Rx HW.
+ * RRD: Receive Return Descriptor ring.
+ * Ring of descriptors with buffers filled with received data.
+ */
+
+#ifndef _EMAC_HW_H_
+#define _EMAC_HW_H_
+
+/* EMAC_CSR register offsets */
+#define EMAC_EMAC_WRAPPER_CSR1 0x000000
+#define EMAC_EMAC_WRAPPER_CSR2 0x000004
+#define EMAC_EMAC_WRAPPER_TX_TS_LO 0x000104
+#define EMAC_EMAC_WRAPPER_TX_TS_HI 0x000108
+#define EMAC_EMAC_WRAPPER_TX_TS_INX 0x00010c
+
+/* DMA Order Settings */
+enum emac_dma_order {
+ emac_dma_ord_in = 1,
+ emac_dma_ord_enh = 2,
+ emac_dma_ord_out = 4
+};
+
+enum emac_dma_req_block {
+ emac_dma_req_128 = 0,
+ emac_dma_req_256 = 1,
+ emac_dma_req_512 = 2,
+ emac_dma_req_1024 = 3,
+ emac_dma_req_2048 = 4,
+ emac_dma_req_4096 = 5
+};
+
+/* Returns the value of bits idx...idx+n_bits */
+#define BITS_GET(val, lo, hi) ((le32_to_cpu(val) & GENMASK((hi), (lo))) >> lo)
+#define BITS_SET(val, lo, hi, new_val) \
+ val = cpu_to_le32((le32_to_cpu(val) & (~GENMASK((hi), (lo)))) | \
+ (((new_val) << (lo)) & GENMASK((hi), (lo))))
+
+/* RRD (Receive Return Descriptor) */
+struct emac_rrd {
+ u32 word[6];
+
+/* number of RFD */
+#define RRD_NOR(rrd) BITS_GET((rrd)->word[0], 16, 19)
+/* start consumer index of rfd-ring */
+#define RRD_SI(rrd) BITS_GET((rrd)->word[0], 20, 31)
+/* vlan-tag (CVID, CFI and PRI) */
+#define RRD_CVALN_TAG(rrd) BITS_GET((rrd)->word[2], 0, 15)
+/* length of the packet */
+#define RRD_PKT_SIZE(rrd) BITS_GET((rrd)->word[3], 0, 13)
+/* L4(TCP/UDP) checksum failed */
+#define RRD_L4F(rrd) BITS_GET((rrd)->word[3], 14, 14)
+/* vlan tagged */
+#define RRD_CVTAG(rrd) BITS_GET((rrd)->word[3], 16, 16)
+/* When set, indicates that the descriptor is updated by the IP core.
+ * When cleared, indicates that the descriptor is invalid.
+ */
+#define RRD_UPDT(rrd) BITS_GET((rrd)->word[3], 31, 31)
+#define RRD_UPDT_SET(rrd, val) BITS_SET((rrd)->word[3], 31, 31, val)
+/* timestamp low */
+#define RRD_TS_LOW(rrd) BITS_GET((rrd)->word[4], 0, 29)
+/* timestamp high */
+#define RRD_TS_HI(rrd) le32_to_cpu((rrd)->word[5])
+};
+
+/* TPD (Transmit Packet Descriptor) */
+struct emac_tpd {
+ u32 word[4];
+
+/* Number of bytes of the transmit packet. (include 4-byte CRC) */
+#define TPD_BUF_LEN_SET(tpd, val) BITS_SET((tpd)->word[0], 0, 15, val)
+/* Custom Checksum Offload: When set, ask IP core to offload custom checksum */
+#define TPD_CSX_SET(tpd, val) BITS_SET((tpd)->word[1], 8, 8, val)
+/* TCP Large Send Offload: When set, ask IP core to do offload TCP Large Send */
+#define TPD_LSO(tpd) BITS_GET((tpd)->word[1], 12, 12)
+#define TPD_LSO_SET(tpd, val) BITS_SET((tpd)->word[1], 12, 12, val)
+/* Large Send Offload Version: When set, indicates this is an LSOv2
+ * (for both IPv4 and IPv6). When cleared, indicates this is an LSOv1
+ * (only for IPv4).
+ */
+#define TPD_LSOV_SET(tpd, val) BITS_SET((tpd)->word[1], 13, 13, val)
+/* IPv4 packet: When set, indicates this is an IPv4 packet, this bit is only
+ * for LSOV2 format.
+ */
+#define TPD_IPV4_SET(tpd, val) BITS_SET((tpd)->word[1], 16, 16, val)
+/* 0: Ethernet frame (DA+SA+TYPE+DATA+CRC)
+ * 1: IEEE 802.3 frame (DA+SA+LEN+DSAP+SSAP+CTL+ORG+TYPE+DATA+CRC)
+ */
+#define TPD_TYP_SET(tpd, val) BITS_SET((tpd)->word[1], 17, 17, val)
+/* Low-32bit Buffer Address */
+#define TPD_BUFFER_ADDR_L_SET(tpd, val) ((tpd)->word[2] = cpu_to_le32(val))
+/* CVLAN Tag to be inserted if INS_VLAN_TAG is set, CVLAN TPID based on global
+ * register configuration.
+ */
+#define TPD_CVLAN_TAG_SET(tpd, val) BITS_SET((tpd)->word[3], 0, 15, val)
+/* Insert CVlan Tag: When set, ask MAC to insert CVLAN TAG to outgoing packet
+ */
+#define TPD_INSTC_SET(tpd, val) BITS_SET((tpd)->word[3], 17, 17, val)
+/* High-14bit Buffer Address, So, the 64b-bit address is
+ * {DESC_CTRL_11_TX_DATA_HIADDR[17:0],(register) BUFFER_ADDR_H, BUFFER_ADDR_L}
+ */
+#define TPD_BUFFER_ADDR_H_SET(tpd, val) BITS_SET((tpd)->word[3], 18, 30, val)
+/* Format D. Word offset from the 1st byte of this packet to start to calculate
+ * the custom checksum.
+ */
+#define TPD_PAYLOAD_OFFSET_SET(tpd, val) BITS_SET((tpd)->word[1], 0, 7, val)
+/* Format D. Word offset from the 1st byte of this packet to fill the custom
+ * checksum to
+ */
+#define TPD_CXSUM_OFFSET_SET(tpd, val) BITS_SET((tpd)->word[1], 18, 25, val)
+
+/* Format C. TCP Header offset from the 1st byte of this packet. (byte unit) */
+#define TPD_TCPHDR_OFFSET_SET(tpd, val) BITS_SET((tpd)->word[1], 0, 7, val)
+/* Format C. MSS (Maximum Segment Size) got from the protocol layer. (byte unit)
+ */
+#define TPD_MSS_SET(tpd, val) BITS_SET((tpd)->word[1], 18, 30, val)
+/* packet length in ext tpd */
+#define TPD_PKT_LEN_SET(tpd, val) ((tpd)->word[2] = cpu_to_le32(val))
+};
+
+/* emac_ring_header represents a single, contiguous block of DMA space
+ * mapped for the three descriptor rings (tpd, rfd, rrd)
+ */
+struct emac_ring_header {
+ void *v_addr; /* virtual address */
+ dma_addr_t dma_addr; /* dma address */
+ size_t size; /* length in bytes */
+ size_t used;
+};
+
+/* emac_buffer is wrapper around a pointer to a socket buffer
+ * so a DMA handle can be stored along with the skb
+ */
+struct emac_buffer {
+ struct sk_buff *skb; /* socket buffer */
+ u16 length; /* rx buffer length */
+ dma_addr_t dma_addr; /* dma address */
+};
+
+/* receive free descriptor (rfd) ring */
+struct emac_rfd_ring {
+ struct emac_buffer *rfbuff;
+ u32 __iomem *v_addr; /* virtual address */
+ dma_addr_t dma_addr; /* dma address */
+ size_t size; /* length in bytes */
+ unsigned int count; /* number of desc in the ring */
+ unsigned int produce_idx;
+ unsigned int process_idx;
+ unsigned int consume_idx; /* unused */
+};
+
+/* Receive Return Desciptor (RRD) ring */
+struct emac_rrd_ring {
+ u32 __iomem *v_addr; /* virtual address */
+ dma_addr_t dma_addr; /* physical address */
+ size_t size; /* length in bytes */
+ unsigned int count; /* number of desc in the ring */
+ unsigned int produce_idx; /* unused */
+ unsigned int consume_idx;
+};
+
+/* Rx queue */
+struct emac_rx_queue {
+ struct net_device *netdev; /* netdev ring belongs to */
+ struct emac_rrd_ring rrd;
+ struct emac_rfd_ring rfd;
+ struct napi_struct napi;
+ struct emac_irq *irq;
+
+ u32 intr;
+ u32 produce_mask;
+ u32 process_mask;
+ u32 consume_mask;
+
+ u16 produce_reg;
+ u16 process_reg;
+ u16 consume_reg;
+
+ u8 produce_shift;
+ u8 process_shft;
+ u8 consume_shift;
+};
+
+/* Transimit Packet Descriptor (tpd) ring */
+struct emac_tpd_ring {
+ struct emac_buffer *tpbuff;
+ u32 __iomem *v_addr; /* virtual address */
+ dma_addr_t dma_addr; /* dma address */
+
+ size_t size; /* length in bytes */
+ unsigned int count; /* number of desc in the ring */
+ unsigned int produce_idx;
+ unsigned int consume_idx;
+ unsigned int last_produce_idx;
+};
+
+/* Tx queue */
+struct emac_tx_queue {
+ struct emac_tpd_ring tpd;
+
+ u32 produce_mask;
+ u32 consume_mask;
+
+ u16 max_packets; /* max packets per interrupt */
+ u16 produce_reg;
+ u16 consume_reg;
+
+ u8 produce_shift;
+ u8 consume_shift;
+};
+
+struct emac_adapter;
+
+int emac_mac_up(struct emac_adapter *adpt);
+void emac_mac_down(struct emac_adapter *adpt);
+void emac_mac_reset(struct emac_adapter *adpt);
+void emac_mac_start(struct emac_adapter *adpt);
+void emac_mac_stop(struct emac_adapter *adpt);
+void emac_mac_mode_config(struct emac_adapter *adpt);
+void emac_mac_rx_process(struct emac_adapter *adpt, struct emac_rx_queue *rx_q,
+ int *num_pkts, int max_pkts);
+int emac_mac_tx_buf_send(struct emac_adapter *adpt, struct emac_tx_queue *tx_q,
+ struct sk_buff *skb);
+void emac_mac_tx_process(struct emac_adapter *adpt, struct emac_tx_queue *tx_q);
+void emac_mac_rx_tx_ring_init_all(struct platform_device *pdev,
+ struct emac_adapter *adpt);
+int emac_mac_rx_tx_rings_alloc_all(struct emac_adapter *adpt);
+void emac_mac_rx_tx_rings_free_all(struct emac_adapter *adpt);
+void emac_mac_multicast_addr_clear(struct emac_adapter *adpt);
+void emac_mac_multicast_addr_set(struct emac_adapter *adpt, u8 *addr);
+
+#endif /*_EMAC_HW_H_*/
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-phy.c b/drivers/net/ethernet/qualcomm/emac/emac-phy.c
new file mode 100644
index 0000000..de6919c
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-phy.c
@@ -0,0 +1,203 @@
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC PHY Controller driver.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+#include <linux/phy.h>
+#include <linux/iopoll.h>
+#include "emac.h"
+#include "emac-mac.h"
+#include "emac-phy.h"
+#include "emac-sgmii.h"
+
+/* EMAC base register offsets */
+#define EMAC_MDIO_CTRL 0x001414
+#define EMAC_PHY_STS 0x001418
+#define EMAC_MDIO_EX_CTRL 0x001440
+
+/* EMAC_MDIO_CTRL */
+#define MDIO_MODE BIT(30)
+#define MDIO_PR BIT(29)
+#define MDIO_AP_EN BIT(28)
+#define MDIO_BUSY BIT(27)
+#define MDIO_CLK_SEL_BMSK 0x7000000
+#define MDIO_CLK_SEL_SHFT 24
+#define MDIO_START BIT(23)
+#define SUP_PREAMBLE BIT(22)
+#define MDIO_RD_NWR BIT(21)
+#define MDIO_REG_ADDR_BMSK 0x1f0000
+#define MDIO_REG_ADDR_SHFT 16
+#define MDIO_DATA_BMSK 0xffff
+#define MDIO_DATA_SHFT 0
+
+/* EMAC_PHY_STS */
+#define PHY_ADDR_BMSK 0x1f0000
+#define PHY_ADDR_SHFT 16
+
+#define MDIO_CLK_25_4 0
+#define MDIO_CLK_25_28 7
+
+#define MDIO_WAIT_TIMES 1000
+
+#define EMAC_LINK_SPEED_DEFAULT (\
+ EMAC_LINK_SPEED_10_HALF |\
+ EMAC_LINK_SPEED_10_FULL |\
+ EMAC_LINK_SPEED_100_HALF |\
+ EMAC_LINK_SPEED_100_FULL |\
+ EMAC_LINK_SPEED_1GB_FULL)
+
+/**
+ * emac_phy_mdio_autopoll_disable() - disable mdio autopoll
+ * @adpt: the emac adapter
+ *
+ * The autopoll feature takes over the MDIO bus. In order for
+ * the PHY driver to be able to talk to the PHY over the MDIO
+ * bus, we need to temporarily disable the autopoll feature.
+ */
+static int emac_phy_mdio_autopoll_disable(struct emac_adapter *adpt)
+{
+ u32 val;
+
+ /* disable autopoll */
+ emac_reg_update32(adpt->base + EMAC_MDIO_CTRL, MDIO_AP_EN, 0);
+
+ /* wait for any mdio polling to complete */
+ if (!readl_poll_timeout(adpt->base + EMAC_MDIO_CTRL, val,
+ !(val & MDIO_BUSY), 100, MDIO_WAIT_TIMES * 100))
+ return 0;
+
+ /* failed to disable; ensure it is enabled before returning */
+ emac_reg_update32(adpt->base + EMAC_MDIO_CTRL, 0, MDIO_AP_EN);
+
+ return -EBUSY;
+}
+
+/**
+ * emac_phy_mdio_autopoll_disable() - disable mdio autopoll
+ * @adpt: the emac adapter
+ *
+ * The EMAC has the ability to poll the external PHY on the MDIO
+ * bus for link state changes. This eliminates the need for the
+ * driver to poll the phy. If if the link state does change,
+ * the EMAC issues an interrupt on behalf of the PHY.
+ */
+static void emac_phy_mdio_autopoll_enable(struct emac_adapter *adpt)
+{
+ emac_reg_update32(adpt->base + EMAC_MDIO_CTRL, 0, MDIO_AP_EN);
+}
+
+static int emac_mdio_read(struct mii_bus *bus, int addr, int regnum)
+{
+ struct emac_adapter *adpt = bus->priv;
+ u32 reg;
+ int ret;
+
+ ret = emac_phy_mdio_autopoll_disable(adpt);
+ if (ret)
+ return ret;
+
+ emac_reg_update32(adpt->base + EMAC_PHY_STS, PHY_ADDR_BMSK,
+ (addr << PHY_ADDR_SHFT));
+
+ reg = SUP_PREAMBLE |
+ ((MDIO_CLK_25_4 << MDIO_CLK_SEL_SHFT) & MDIO_CLK_SEL_BMSK) |
+ ((regnum << MDIO_REG_ADDR_SHFT) & MDIO_REG_ADDR_BMSK) |
+ MDIO_START | MDIO_RD_NWR;
+
+ writel(reg, adpt->base + EMAC_MDIO_CTRL);
+
+ if (readl_poll_timeout(adpt->base + EMAC_MDIO_CTRL, reg,
+ !(reg & (MDIO_START | MDIO_BUSY)),
+ 100, MDIO_WAIT_TIMES * 100))
+ ret = -EIO;
+ else
+ ret = (reg >> MDIO_DATA_SHFT) & MDIO_DATA_BMSK;
+
+ emac_phy_mdio_autopoll_enable(adpt);
+
+ return ret;
+}
+
+static int emac_mdio_write(struct mii_bus *bus, int addr, int regnum, u16 val)
+{
+ struct emac_adapter *adpt = bus->priv;
+ u32 reg;
+ int ret;
+
+ ret = emac_phy_mdio_autopoll_disable(adpt);
+ if (ret)
+ return ret;
+
+ emac_reg_update32(adpt->base + EMAC_PHY_STS, PHY_ADDR_BMSK,
+ (addr << PHY_ADDR_SHFT));
+
+ reg = SUP_PREAMBLE |
+ ((MDIO_CLK_25_4 << MDIO_CLK_SEL_SHFT) & MDIO_CLK_SEL_BMSK) |
+ ((regnum << MDIO_REG_ADDR_SHFT) & MDIO_REG_ADDR_BMSK) |
+ ((val << MDIO_DATA_SHFT) & MDIO_DATA_BMSK) |
+ MDIO_START;
+
+ writel(reg, adpt->base + EMAC_MDIO_CTRL);
+
+ if (readl_poll_timeout(adpt->base + EMAC_MDIO_CTRL, reg,
+ !(reg & (MDIO_START | MDIO_BUSY)), 100,
+ MDIO_WAIT_TIMES * 100))
+ ret = -EIO;
+
+ emac_phy_mdio_autopoll_enable(adpt);
+
+ return ret;
+}
+
+/* Configure the MDIO bus and connect the external PHY */
+int emac_phy_config(struct platform_device *pdev, struct emac_adapter *adpt)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *phy_np;
+ struct mii_bus *mii_bus;
+ int ret;
+
+ /* Create the mii_bus object for talking to the MDIO bus */
+ adpt->mii_bus = mii_bus = devm_mdiobus_alloc(&pdev->dev);
+ if (!mii_bus)
+ return -ENOMEM;
+
+ mii_bus->name = "emac-mdio";
+ snprintf(mii_bus->id, MII_BUS_ID_SIZE, "%s", pdev->name);
+ mii_bus->read = emac_mdio_read;
+ mii_bus->write = emac_mdio_write;
+ mii_bus->parent = &pdev->dev;
+ mii_bus->priv = adpt;
+
+ ret = of_mdiobus_register(mii_bus, np);
+ if (ret) {
+ dev_err(&pdev->dev, "could not register mdio bus\n");
+ return ret;
+ }
+
+ phy_np = of_parse_phandle(np, "phy-handle", 0);
+ adpt->phydev = of_phy_find_device(phy_np);
+ if (!adpt->phydev) {
+ dev_err(&pdev->dev, "could not find external phy\n");
+ mdiobus_unregister(mii_bus);
+ return -ENODEV;
+ }
+
+ phy_attached_print(adpt->phydev, NULL);
+
+ return 0;
+}
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-phy.h b/drivers/net/ethernet/qualcomm/emac/emac-phy.h
new file mode 100644
index 0000000..49f3701
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-phy.h
@@ -0,0 +1,33 @@
+/* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+*
+* This program is free software; you can redistribute it and/or modify
+* it under the terms of the GNU General Public License version 2 and
+* only version 2 as published by the Free Software Foundation.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+* GNU General Public License for more details.
+*/
+
+#ifndef _EMAC_PHY_H_
+#define _EMAC_PHY_H_
+
+typedef int (*emac_sgmii_initialize)(struct emac_adapter *adpt);
+
+/** emac_phy - internal emac phy
+ * @base base address
+ * @digital per-lane digital block
+ * @initialize initialization function
+ */
+struct emac_phy {
+ void __iomem *base;
+ void __iomem *digital;
+ emac_sgmii_initialize initialize;
+};
+
+struct emac_adapter;
+
+int emac_phy_config(struct platform_device *pdev, struct emac_adapter *adpt);
+
+#endif /* _EMAC_PHY_H_ */
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
new file mode 100644
index 0000000..ca084db
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
@@ -0,0 +1,722 @@
+/* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC SGMII Controller driver.
+ */
+
+#include <linux/iopoll.h>
+#include <linux/of_device.h>
+#include "emac.h"
+#include "emac-mac.h"
+#include "emac-sgmii.h"
+
+/* EMAC_QSERDES register offsets */
+#define EMAC_QSERDES_COM_SYS_CLK_CTRL 0x000000
+#define EMAC_QSERDES_COM_PLL_CNTRL 0x000014
+#define EMAC_QSERDES_COM_PLL_IP_SETI 0x000018
+#define EMAC_QSERDES_COM_PLL_CP_SETI 0x000024
+#define EMAC_QSERDES_COM_PLL_IP_SETP 0x000028
+#define EMAC_QSERDES_COM_PLL_CP_SETP 0x00002c
+#define EMAC_QSERDES_COM_SYSCLK_EN_SEL 0x000038
+#define EMAC_QSERDES_COM_RESETSM_CNTRL 0x000040
+#define EMAC_QSERDES_COM_PLLLOCK_CMP1 0x000044
+#define EMAC_QSERDES_COM_PLLLOCK_CMP2 0x000048
+#define EMAC_QSERDES_COM_PLLLOCK_CMP3 0x00004c
+#define EMAC_QSERDES_COM_PLLLOCK_CMP_EN 0x000050
+#define EMAC_QSERDES_COM_DEC_START1 0x000064
+#define EMAC_QSERDES_COM_DIV_FRAC_START1 0x000098
+#define EMAC_QSERDES_COM_DIV_FRAC_START2 0x00009c
+#define EMAC_QSERDES_COM_DIV_FRAC_START3 0x0000a0
+#define EMAC_QSERDES_COM_DEC_START2 0x0000a4
+#define EMAC_QSERDES_COM_PLL_CRCTRL 0x0000ac
+#define EMAC_QSERDES_COM_RESET_SM 0x0000bc
+#define EMAC_QSERDES_TX_BIST_MODE_LANENO 0x000100
+#define EMAC_QSERDES_TX_TX_EMP_POST1_LVL 0x000108
+#define EMAC_QSERDES_TX_TX_DRV_LVL 0x00010c
+#define EMAC_QSERDES_TX_LANE_MODE 0x000150
+#define EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN 0x000170
+#define EMAC_QSERDES_RX_CDR_CONTROL 0x000200
+#define EMAC_QSERDES_RX_CDR_CONTROL2 0x000210
+#define EMAC_QSERDES_RX_RX_EQ_GAIN12 0x000230
+
+/* EMAC_SGMII register offsets */
+#define EMAC_SGMII_PHY_SERDES_START 0x000000
+#define EMAC_SGMII_PHY_CMN_PWR_CTRL 0x000004
+#define EMAC_SGMII_PHY_RX_PWR_CTRL 0x000008
+#define EMAC_SGMII_PHY_TX_PWR_CTRL 0x00000C
+#define EMAC_SGMII_PHY_LANE_CTRL1 0x000018
+#define EMAC_SGMII_PHY_AUTONEG_CFG2 0x000048
+#define EMAC_SGMII_PHY_CDR_CTRL0 0x000058
+#define EMAC_SGMII_PHY_SPEED_CFG1 0x000074
+#define EMAC_SGMII_PHY_POW_DWN_CTRL0 0x000080
+#define EMAC_SGMII_PHY_RESET_CTRL 0x0000a8
+#define EMAC_SGMII_PHY_IRQ_CMD 0x0000ac
+#define EMAC_SGMII_PHY_INTERRUPT_CLEAR 0x0000b0
+#define EMAC_SGMII_PHY_INTERRUPT_MASK 0x0000b4
+#define EMAC_SGMII_PHY_INTERRUPT_STATUS 0x0000b8
+#define EMAC_SGMII_PHY_RX_CHK_STATUS 0x0000d4
+#define EMAC_SGMII_PHY_AUTONEG0_STATUS 0x0000e0
+#define EMAC_SGMII_PHY_AUTONEG1_STATUS 0x0000e4
+
+/* EMAC_QSERDES_COM_PLL_IP_SETI */
+#define PLL_IPSETI(x) ((x) & 0x3f)
+
+/* EMAC_QSERDES_COM_PLL_CP_SETI */
+#define PLL_CPSETI(x) ((x) & 0xff)
+
+/* EMAC_QSERDES_COM_PLL_IP_SETP */
+#define PLL_IPSETP(x) ((x) & 0x3f)
+
+/* EMAC_QSERDES_COM_PLL_CP_SETP */
+#define PLL_CPSETP(x) ((x) & 0x1f)
+
+/* EMAC_QSERDES_COM_PLL_CRCTRL */
+#define PLL_RCTRL(x) (((x) & 0xf) << 4)
+#define PLL_CCTRL(x) ((x) & 0xf)
+
+/* SGMII v2 PHY registers per lane */
+#define EMAC_SGMII_PHY_LN_OFFSET 0x0400
+
+/* SGMII v2 digital lane registers */
+#define EMAC_SGMII_LN_DRVR_CTRL0 0x00C
+#define EMAC_SGMII_LN_DRVR_TAP_EN 0x018
+#define EMAC_SGMII_LN_TX_MARGINING 0x01C
+#define EMAC_SGMII_LN_TX_PRE 0x020
+#define EMAC_SGMII_LN_TX_POST 0x024
+#define EMAC_SGMII_LN_TX_BAND_MODE 0x060
+#define EMAC_SGMII_LN_LANE_MODE 0x064
+#define EMAC_SGMII_LN_PARALLEL_RATE 0x078
+#define EMAC_SGMII_LN_CML_CTRL_MODE0 0x0B8
+#define EMAC_SGMII_LN_MIXER_CTRL_MODE0 0x0D0
+#define EMAC_SGMII_LN_VGA_INITVAL 0x134
+#define EMAC_SGMII_LN_UCDR_FO_GAIN_MODE0 0x17C
+#define EMAC_SGMII_LN_UCDR_SO_GAIN_MODE0 0x188
+#define EMAC_SGMII_LN_UCDR_SO_CONFIG 0x194
+#define EMAC_SGMII_LN_RX_BAND 0x19C
+#define EMAC_SGMII_LN_RX_RCVR_PATH1_MODE0 0x1B8
+#define EMAC_SGMII_LN_RSM_CONFIG 0x1F0
+#define EMAC_SGMII_LN_SIGDET_ENABLES 0x224
+#define EMAC_SGMII_LN_SIGDET_CNTRL 0x228
+#define EMAC_SGMII_LN_SIGDET_DEGLITCH_CNTRL 0x22C
+#define EMAC_SGMII_LN_RX_EN_SIGNAL 0x2A0
+#define EMAC_SGMII_LN_RX_MISC_CNTRL0 0x2AC
+#define EMAC_SGMII_LN_DRVR_LOGIC_CLKDIV 0x2BC
+
+/* SGMII v2 digital lane register values */
+#define UCDR_STEP_BY_TWO_MODE0 BIT(7)
+#define UCDR_xO_GAIN_MODE(x) ((x) & 0x7f)
+#define UCDR_ENABLE BIT(6)
+#define UCDR_SO_SATURATION(x) ((x) & 0x3f)
+#define SIGDET_LP_BYP_PS4 BIT(7)
+#define SIGDET_EN_PS0_TO_PS2 BIT(6)
+#define EN_ACCOUPLEVCM_SW_MUX BIT(5)
+#define EN_ACCOUPLEVCM_SW BIT(4)
+#define RX_SYNC_EN BIT(3)
+#define RXTERM_HIGHZ_PS5 BIT(2)
+#define SIGDET_EN_PS3 BIT(1)
+#define EN_ACCOUPLE_VCM_PS3 BIT(0)
+#define UFS_MODE BIT(5)
+#define TXVAL_VALID_INIT BIT(4)
+#define TXVAL_VALID_MUX BIT(3)
+#define TXVAL_VALID BIT(2)
+#define USB3P1_MODE BIT(1)
+#define KR_PCIGEN3_MODE BIT(0)
+#define PRE_EN BIT(3)
+#define POST_EN BIT(2)
+#define MAIN_EN_MUX BIT(1)
+#define MAIN_EN BIT(0)
+#define TX_MARGINING_MUX BIT(6)
+#define TX_MARGINING(x) ((x) & 0x3f)
+#define TX_PRE_MUX BIT(6)
+#define TX_PRE(x) ((x) & 0x3f)
+#define TX_POST_MUX BIT(6)
+#define TX_POST(x) ((x) & 0x3f)
+#define CML_GEAR_MODE(x) (((x) & 7) << 3)
+#define CML2CMOS_IBOOST_MODE(x) ((x) & 7)
+#define MIXER_LOADB_MODE(x) (((x) & 0xf) << 2)
+#define MIXER_DATARATE_MODE(x) ((x) & 3)
+#define VGA_THRESH_DFE(x) ((x) & 0x3f)
+#define SIGDET_LP_BYP_PS0_TO_PS2 BIT(5)
+#define SIGDET_LP_BYP_MUX BIT(4)
+#define SIGDET_LP_BYP BIT(3)
+#define SIGDET_EN_MUX BIT(2)
+#define SIGDET_EN BIT(1)
+#define SIGDET_FLT_BYP BIT(0)
+#define SIGDET_LVL(x) (((x) & 0xf) << 4)
+#define SIGDET_BW_CTRL(x) ((x) & 0xf)
+#define SIGDET_DEGLITCH_CTRL(x) (((x) & 0xf) << 1)
+#define SIGDET_DEGLITCH_BYP BIT(0)
+#define INVERT_PCS_RX_CLK BIT(7)
+#define PWM_EN BIT(6)
+#define RXBIAS_SEL(x) (((x) & 0x3) << 4)
+#define EBDAC_SIGN BIT(3)
+#define EDAC_SIGN BIT(2)
+#define EN_AUXTAP1SIGN_INVERT BIT(1)
+#define EN_DAC_CHOPPING BIT(0)
+#define DRVR_LOGIC_CLK_EN BIT(4)
+#define DRVR_LOGIC_CLK_DIV(x) ((x) & 0xf)
+#define PARALLEL_RATE_MODE2(x) (((x) & 0x3) << 4)
+#define PARALLEL_RATE_MODE1(x) (((x) & 0x3) << 2)
+#define PARALLEL_RATE_MODE0(x) ((x) & 0x3)
+#define BAND_MODE2(x) (((x) & 0x3) << 4)
+#define BAND_MODE1(x) (((x) & 0x3) << 2)
+#define BAND_MODE0(x) ((x) & 0x3)
+#define LANE_SYNC_MODE BIT(5)
+#define LANE_MODE(x) ((x) & 0x1f)
+#define CDR_PD_SEL_MODE0(x) (((x) & 0x3) << 5)
+#define EN_DLL_MODE0 BIT(4)
+#define EN_IQ_DCC_MODE0 BIT(3)
+#define EN_IQCAL_MODE0 BIT(2)
+#define EN_QPATH_MODE0 BIT(1)
+#define EN_EPATH_MODE0 BIT(0)
+#define FORCE_TSYNC_ACK BIT(7)
+#define FORCE_CMN_ACK BIT(6)
+#define FORCE_CMN_READY BIT(5)
+#define EN_RCLK_DEGLITCH BIT(4)
+#define BYPASS_RSM_CDR_RESET BIT(3)
+#define BYPASS_RSM_TSYNC BIT(2)
+#define BYPASS_RSM_SAMP_CAL BIT(1)
+#define BYPASS_RSM_DLL_CAL BIT(0)
+
+/* EMAC_QSERDES_COM_SYS_CLK_CTRL */
+#define SYSCLK_CM BIT(4)
+#define SYSCLK_AC_COUPLE BIT(3)
+
+/* EMAC_QSERDES_COM_PLL_CNTRL */
+#define OCP_EN BIT(5)
+#define PLL_DIV_FFEN BIT(2)
+#define PLL_DIV_ORD BIT(1)
+
+/* EMAC_QSERDES_COM_SYSCLK_EN_SEL */
+#define SYSCLK_SEL_CMOS BIT(3)
+
+/* EMAC_QSERDES_COM_RESETSM_CNTRL */
+#define FRQ_TUNE_MODE BIT(4)
+
+/* EMAC_QSERDES_COM_PLLLOCK_CMP_EN */
+#define PLLLOCK_CMP_EN BIT(0)
+
+/* EMAC_QSERDES_COM_DEC_START1 */
+#define DEC_START1_MUX BIT(7)
+#define DEC_START1(x) ((x) & 0x7f)
+
+/* EMAC_QSERDES_COM_DIV_FRAC_START1 * EMAC_QSERDES_COM_DIV_FRAC_START2 */
+#define DIV_FRAC_START_MUX BIT(7)
+#define DIV_FRAC_START(x) ((x) & 0x7f)
+
+/* EMAC_QSERDES_COM_DIV_FRAC_START3 */
+#define DIV_FRAC_START3_MUX BIT(4)
+#define DIV_FRAC_START3(x) ((x) & 0xf)
+
+/* EMAC_QSERDES_COM_DEC_START2 */
+#define DEC_START2_MUX BIT(1)
+#define DEC_START2 BIT(0)
+
+/* EMAC_QSERDES_COM_RESET_SM */
+#define READY BIT(5)
+
+/* EMAC_QSERDES_TX_TX_EMP_POST1_LVL */
+#define TX_EMP_POST1_LVL_MUX BIT(5)
+#define TX_EMP_POST1_LVL(x) ((x) & 0x1f)
+#define TX_EMP_POST1_LVL_BMSK 0x1f
+#define TX_EMP_POST1_LVL_SHFT 0
+
+/* EMAC_QSERDES_TX_TX_DRV_LVL */
+#define TX_DRV_LVL_MUX BIT(4)
+#define TX_DRV_LVL(x) ((x) & 0xf)
+
+/* EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN */
+#define EMP_EN_MUX BIT(1)
+#define EMP_EN BIT(0)
+
+/* EMAC_QSERDES_RX_CDR_CONTROL & EMAC_QSERDES_RX_CDR_CONTROL2 */
+#define HBW_PD_EN BIT(7)
+#define SECONDORDERENABLE BIT(6)
+#define FIRSTORDER_THRESH(x) (((x) & 0x7) << 3)
+#define SECONDORDERGAIN(x) ((x) & 0x7)
+
+/* EMAC_QSERDES_RX_RX_EQ_GAIN12 */
+#define RX_EQ_GAIN2(x) (((x) & 0xf) << 4)
+#define RX_EQ_GAIN1(x) ((x) & 0xf)
+
+/* EMAC_SGMII_PHY_SERDES_START */
+#define SERDES_START BIT(0)
+
+/* EMAC_SGMII_PHY_CMN_PWR_CTRL */
+#define BIAS_EN BIT(6)
+#define PLL_EN BIT(5)
+#define SYSCLK_EN BIT(4)
+#define CLKBUF_L_EN BIT(3)
+#define PLL_TXCLK_EN BIT(1)
+#define PLL_RXCLK_EN BIT(0)
+
+/* EMAC_SGMII_PHY_RX_PWR_CTRL */
+#define L0_RX_SIGDET_EN BIT(7)
+#define L0_RX_TERM_MODE(x) (((x) & 3) << 4)
+#define L0_RX_I_EN BIT(1)
+
+/* EMAC_SGMII_PHY_TX_PWR_CTRL */
+#define L0_TX_EN BIT(5)
+#define L0_CLKBUF_EN BIT(4)
+#define L0_TRAN_BIAS_EN BIT(1)
+
+/* EMAC_SGMII_PHY_LANE_CTRL1 */
+#define L0_RX_EQUALIZE_ENABLE BIT(6)
+#define L0_RESET_TSYNC_EN BIT(4)
+#define L0_DRV_LVL(x) ((x) & 0xf)
+
+/* EMAC_SGMII_PHY_AUTONEG_CFG2 */
+#define FORCE_AN_TX_CFG BIT(5)
+#define FORCE_AN_RX_CFG BIT(4)
+#define AN_ENABLE BIT(0)
+
+/* EMAC_SGMII_PHY_SPEED_CFG1 */
+#define DUPLEX_MODE BIT(4)
+#define SPDMODE_1000 BIT(1)
+#define SPDMODE_100 BIT(0)
+#define SPDMODE_10 0
+#define SPDMODE_BMSK 3
+#define SPDMODE_SHFT 0
+
+/* EMAC_SGMII_PHY_POW_DWN_CTRL0 */
+#define PWRDN_B BIT(0)
+#define CDR_MAX_CNT(x) ((x) & 0xff)
+
+/* EMAC_QSERDES_TX_BIST_MODE_LANENO */
+#define BIST_LANE_NUMBER(x) (((x) & 3) << 5)
+#define BISTMODE(x) ((x) & 0x1f)
+
+/* EMAC_QSERDES_COM_PLLLOCK_CMPx */
+#define PLLLOCK_CMP(x) ((x) & 0xff)
+
+/* EMAC_SGMII_PHY_RESET_CTRL */
+#define PHY_SW_RESET BIT(0)
+
+/* EMAC_SGMII_PHY_IRQ_CMD */
+#define IRQ_GLOBAL_CLEAR BIT(0)
+
+/* EMAC_SGMII_PHY_INTERRUPT_MASK */
+#define DECODE_CODE_ERR BIT(7)
+#define DECODE_DISP_ERR BIT(6)
+#define PLL_UNLOCK BIT(5)
+#define AN_ILLEGAL_TERM BIT(4)
+#define SYNC_FAIL BIT(3)
+#define AN_START BIT(2)
+#define AN_END BIT(1)
+#define AN_REQUEST BIT(0)
+
+#define SGMII_PHY_IRQ_CLR_WAIT_TIME 10
+
+#define SGMII_PHY_INTERRUPT_ERR (\
+ DECODE_CODE_ERR |\
+ DECODE_DISP_ERR)
+
+#define SGMII_ISR_AN_MASK (\
+ AN_REQUEST |\
+ AN_START |\
+ AN_END |\
+ AN_ILLEGAL_TERM |\
+ PLL_UNLOCK |\
+ SYNC_FAIL)
+
+#define SGMII_ISR_MASK (\
+ SGMII_PHY_INTERRUPT_ERR |\
+ SGMII_ISR_AN_MASK)
+
+/* SGMII TX_CONFIG */
+#define TXCFG_LINK 0x8000
+#define TXCFG_MODE_BMSK 0x1c00
+#define TXCFG_1000_FULL 0x1800
+#define TXCFG_100_FULL 0x1400
+#define TXCFG_100_HALF 0x0400
+#define TXCFG_10_FULL 0x1000
+#define TXCFG_10_HALF 0x0000
+
+#define SERDES_START_WAIT_TIMES 100
+
+struct emac_reg_write {
+ unsigned int offset;
+ u32 val;
+};
+
+static void emac_reg_write_all(void __iomem *base,
+ const struct emac_reg_write *itr, size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; ++itr, ++i)
+ writel(itr->val, base + itr->offset);
+}
+
+static const struct emac_reg_write physical_coding_sublayer_programming_v1[] = {
+ {EMAC_SGMII_PHY_CDR_CTRL0, CDR_MAX_CNT(15)},
+ {EMAC_SGMII_PHY_POW_DWN_CTRL0, PWRDN_B},
+ {EMAC_SGMII_PHY_CMN_PWR_CTRL,
+ BIAS_EN | SYSCLK_EN | CLKBUF_L_EN | PLL_TXCLK_EN | PLL_RXCLK_EN},
+ {EMAC_SGMII_PHY_TX_PWR_CTRL, L0_TX_EN | L0_CLKBUF_EN | L0_TRAN_BIAS_EN},
+ {EMAC_SGMII_PHY_RX_PWR_CTRL,
+ L0_RX_SIGDET_EN | L0_RX_TERM_MODE(1) | L0_RX_I_EN},
+ {EMAC_SGMII_PHY_CMN_PWR_CTRL,
+ BIAS_EN | PLL_EN | SYSCLK_EN | CLKBUF_L_EN | PLL_TXCLK_EN |
+ PLL_RXCLK_EN},
+ {EMAC_SGMII_PHY_LANE_CTRL1,
+ L0_RX_EQUALIZE_ENABLE | L0_RESET_TSYNC_EN | L0_DRV_LVL(15)},
+};
+
+static const struct emac_reg_write sysclk_refclk_setting[] = {
+ {EMAC_QSERDES_COM_SYSCLK_EN_SEL, SYSCLK_SEL_CMOS},
+ {EMAC_QSERDES_COM_SYS_CLK_CTRL, SYSCLK_CM | SYSCLK_AC_COUPLE},
+};
+
+static const struct emac_reg_write pll_setting[] = {
+ {EMAC_QSERDES_COM_PLL_IP_SETI, PLL_IPSETI(1)},
+ {EMAC_QSERDES_COM_PLL_CP_SETI, PLL_CPSETI(59)},
+ {EMAC_QSERDES_COM_PLL_IP_SETP, PLL_IPSETP(10)},
+ {EMAC_QSERDES_COM_PLL_CP_SETP, PLL_CPSETP(9)},
+ {EMAC_QSERDES_COM_PLL_CRCTRL, PLL_RCTRL(15) | PLL_CCTRL(11)},
+ {EMAC_QSERDES_COM_PLL_CNTRL, OCP_EN | PLL_DIV_FFEN | PLL_DIV_ORD},
+ {EMAC_QSERDES_COM_DEC_START1, DEC_START1_MUX | DEC_START1(2)},
+ {EMAC_QSERDES_COM_DEC_START2, DEC_START2_MUX | DEC_START2},
+ {EMAC_QSERDES_COM_DIV_FRAC_START1,
+ DIV_FRAC_START_MUX | DIV_FRAC_START(85)},
+ {EMAC_QSERDES_COM_DIV_FRAC_START2,
+ DIV_FRAC_START_MUX | DIV_FRAC_START(42)},
+ {EMAC_QSERDES_COM_DIV_FRAC_START3,
+ DIV_FRAC_START3_MUX | DIV_FRAC_START3(3)},
+ {EMAC_QSERDES_COM_PLLLOCK_CMP1, PLLLOCK_CMP(43)},
+ {EMAC_QSERDES_COM_PLLLOCK_CMP2, PLLLOCK_CMP(104)},
+ {EMAC_QSERDES_COM_PLLLOCK_CMP3, PLLLOCK_CMP(0)},
+ {EMAC_QSERDES_COM_PLLLOCK_CMP_EN, PLLLOCK_CMP_EN},
+ {EMAC_QSERDES_COM_RESETSM_CNTRL, FRQ_TUNE_MODE},
+};
+
+static const struct emac_reg_write cdr_setting[] = {
+ {EMAC_QSERDES_RX_CDR_CONTROL,
+ SECONDORDERENABLE | FIRSTORDER_THRESH(3) | SECONDORDERGAIN(2)},
+ {EMAC_QSERDES_RX_CDR_CONTROL2,
+ SECONDORDERENABLE | FIRSTORDER_THRESH(3) | SECONDORDERGAIN(4)},
+};
+
+static const struct emac_reg_write tx_rx_setting[] = {
+ {EMAC_QSERDES_TX_BIST_MODE_LANENO, 0},
+ {EMAC_QSERDES_TX_TX_DRV_LVL, TX_DRV_LVL_MUX | TX_DRV_LVL(15)},
+ {EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN, EMP_EN_MUX | EMP_EN},
+ {EMAC_QSERDES_TX_TX_EMP_POST1_LVL,
+ TX_EMP_POST1_LVL_MUX | TX_EMP_POST1_LVL(1)},
+ {EMAC_QSERDES_RX_RX_EQ_GAIN12, RX_EQ_GAIN2(15) | RX_EQ_GAIN1(15)},
+ {EMAC_QSERDES_TX_LANE_MODE, LANE_MODE(8)},
+};
+
+static const struct emac_reg_write sgmii_v2_laned[] = {
+ /* CDR Settings */
+ {EMAC_SGMII_LN_UCDR_FO_GAIN_MODE0,
+ UCDR_STEP_BY_TWO_MODE0 | UCDR_xO_GAIN_MODE(10)},
+ {EMAC_SGMII_LN_UCDR_SO_GAIN_MODE0, UCDR_xO_GAIN_MODE(6)},
+ {EMAC_SGMII_LN_UCDR_SO_CONFIG, UCDR_ENABLE | UCDR_SO_SATURATION(12)},
+
+ /* TX/RX Settings */
+ {EMAC_SGMII_LN_RX_EN_SIGNAL, SIGDET_LP_BYP_PS4 | SIGDET_EN_PS0_TO_PS2},
+
+ {EMAC_SGMII_LN_DRVR_CTRL0, TXVAL_VALID_INIT | KR_PCIGEN3_MODE},
+ {EMAC_SGMII_LN_DRVR_TAP_EN, MAIN_EN},
+ {EMAC_SGMII_LN_TX_MARGINING, TX_MARGINING_MUX | TX_MARGINING(25)},
+ {EMAC_SGMII_LN_TX_PRE, TX_PRE_MUX},
+ {EMAC_SGMII_LN_TX_POST, TX_POST_MUX},
+
+ {EMAC_SGMII_LN_CML_CTRL_MODE0,
+ CML_GEAR_MODE(1) | CML2CMOS_IBOOST_MODE(1)},
+ {EMAC_SGMII_LN_MIXER_CTRL_MODE0,
+ MIXER_LOADB_MODE(12) | MIXER_DATARATE_MODE(1)},
+ {EMAC_SGMII_LN_VGA_INITVAL, VGA_THRESH_DFE(31)},
+ {EMAC_SGMII_LN_SIGDET_ENABLES,
+ SIGDET_LP_BYP_PS0_TO_PS2 | SIGDET_FLT_BYP},
+ {EMAC_SGMII_LN_SIGDET_CNTRL, SIGDET_LVL(8)},
+
+ {EMAC_SGMII_LN_SIGDET_DEGLITCH_CNTRL, SIGDET_DEGLITCH_CTRL(4)},
+ {EMAC_SGMII_LN_RX_MISC_CNTRL0, 0},
+ {EMAC_SGMII_LN_DRVR_LOGIC_CLKDIV,
+ DRVR_LOGIC_CLK_EN | DRVR_LOGIC_CLK_DIV(4)},
+
+ {EMAC_SGMII_LN_PARALLEL_RATE, PARALLEL_RATE_MODE0(1)},
+ {EMAC_SGMII_LN_TX_BAND_MODE, BAND_MODE0(2)},
+ {EMAC_SGMII_LN_RX_BAND, BAND_MODE0(3)},
+ {EMAC_SGMII_LN_LANE_MODE, LANE_MODE(26)},
+ {EMAC_SGMII_LN_RX_RCVR_PATH1_MODE0, CDR_PD_SEL_MODE0(3)},
+ {EMAC_SGMII_LN_RSM_CONFIG, BYPASS_RSM_SAMP_CAL | BYPASS_RSM_DLL_CAL},
+};
+
+static const struct emac_reg_write physical_coding_sublayer_programming_v2[] = {
+ {EMAC_SGMII_PHY_POW_DWN_CTRL0, PWRDN_B},
+ {EMAC_SGMII_PHY_CDR_CTRL0, CDR_MAX_CNT(15)},
+ {EMAC_SGMII_PHY_TX_PWR_CTRL, 0},
+ {EMAC_SGMII_PHY_LANE_CTRL1, L0_RX_EQUALIZE_ENABLE},
+};
+
+static int emac_sgmii_link_init(struct emac_adapter *adpt)
+{
+ struct phy_device *phydev = adpt->phydev;
+ struct emac_phy *phy = &adpt->phy;
+ u32 val;
+
+ val = readl(phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+
+ if (phydev->autoneg == AUTONEG_ENABLE) {
+ val &= ~(FORCE_AN_RX_CFG | FORCE_AN_TX_CFG);
+ val |= AN_ENABLE;
+ writel(val, phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+ } else {
+ u32 speed_cfg;
+
+ switch (phydev->speed) {
+ case SPEED_10:
+ speed_cfg = SPDMODE_10;
+ break;
+ case SPEED_100:
+ speed_cfg = SPDMODE_100;
+ break;
+ case SPEED_1000:
+ speed_cfg = SPDMODE_1000;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (phydev->duplex == DUPLEX_FULL)
+ speed_cfg |= DUPLEX_MODE;
+
+ val &= ~AN_ENABLE;
+ writel(speed_cfg, phy->base + EMAC_SGMII_PHY_SPEED_CFG1);
+ writel(val, phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+ }
+
+ return 0;
+}
+
+static int emac_sgmii_irq_clear(struct emac_adapter *adpt, u32 irq_bits)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 status;
+
+ writel_relaxed(irq_bits, phy->base + EMAC_SGMII_PHY_INTERRUPT_CLEAR);
+ writel_relaxed(IRQ_GLOBAL_CLEAR, phy->base + EMAC_SGMII_PHY_IRQ_CMD);
+ /* Ensure interrupt clear command is written to HW */
+ wmb();
+
+ /* After set the IRQ_GLOBAL_CLEAR bit, the status clearing must
+ * be confirmed before clearing the bits in other registers.
+ * It takes a few cycles for hw to clear the interrupt status.
+ */
+ if (readl_poll_timeout_atomic(phy->base +
+ EMAC_SGMII_PHY_INTERRUPT_STATUS,
+ status, !(status & irq_bits), 1,
+ SGMII_PHY_IRQ_CLR_WAIT_TIME)) {
+ netdev_err(adpt->netdev,
+ "error: failed clear SGMII irq: status:0x%x bits:0x%x\n",
+ status, irq_bits);
+ return -EIO;
+ }
+
+ /* Finalize clearing procedure */
+ writel_relaxed(0, phy->base + EMAC_SGMII_PHY_IRQ_CMD);
+ writel_relaxed(0, phy->base + EMAC_SGMII_PHY_INTERRUPT_CLEAR);
+
+ /* Ensure that clearing procedure finalization is written to HW */
+ wmb();
+
+ return 0;
+}
+
+int emac_sgmii_init_v1(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ unsigned int i;
+ int ret;
+
+ ret = emac_sgmii_link_init(adpt);
+ if (ret)
+ return ret;
+
+ emac_reg_write_all(phy->base, physical_coding_sublayer_programming_v1,
+ ARRAY_SIZE(physical_coding_sublayer_programming_v1));
+ emac_reg_write_all(phy->base, sysclk_refclk_setting,
+ ARRAY_SIZE(sysclk_refclk_setting));
+ emac_reg_write_all(phy->base, pll_setting, ARRAY_SIZE(pll_setting));
+ emac_reg_write_all(phy->base, cdr_setting, ARRAY_SIZE(cdr_setting));
+ emac_reg_write_all(phy->base, tx_rx_setting,
+ ARRAY_SIZE(tx_rx_setting));
+
+ /* Power up the Ser/Des engine */
+ writel(SERDES_START, phy->base + EMAC_SGMII_PHY_SERDES_START);
+
+ for (i = 0; i < SERDES_START_WAIT_TIMES; i++) {
+ if (readl(phy->base + EMAC_QSERDES_COM_RESET_SM) & READY)
+ break;
+ usleep_range(100, 200);
+ }
+
+ if (i == SERDES_START_WAIT_TIMES) {
+ netdev_err(adpt->netdev, "error: ser/des failed to start\n");
+ return -EIO;
+ }
+ /* Mask out all the SGMII Interrupt */
+ writel(0, phy->base + EMAC_SGMII_PHY_INTERRUPT_MASK);
+
+ emac_sgmii_irq_clear(adpt, SGMII_PHY_INTERRUPT_ERR);
+
+ return 0;
+}
+
+int emac_sgmii_init_v2(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ void __iomem *phy_regs = phy->base;
+ void __iomem *laned = phy->digital;
+ unsigned int i;
+ u32 lnstatus;
+ int ret;
+
+ ret = emac_sgmii_link_init(adpt);
+ if (ret)
+ return ret;
+
+ /* PCS lane-x init */
+ emac_reg_write_all(phy->base, physical_coding_sublayer_programming_v2,
+ ARRAY_SIZE(physical_coding_sublayer_programming_v2));
+
+ /* SGMII lane-x init */
+ emac_reg_write_all(phy->digital,
+ sgmii_v2_laned, ARRAY_SIZE(sgmii_v2_laned));
+
+ /* Power up PCS and start reset lane state machine */
+
+ writel(0, phy_regs + EMAC_SGMII_PHY_RESET_CTRL);
+ writel(1, laned + SGMII_LN_RSM_START);
+
+ /* Wait for c_ready assertion */
+ for (i = 0; i < SERDES_START_WAIT_TIMES; i++) {
+ lnstatus = readl(phy_regs + SGMII_PHY_LN_LANE_STATUS);
+ if (lnstatus & BIT(1))
+ break;
+ usleep_range(100, 200);
+ }
+
+ if (i == SERDES_START_WAIT_TIMES) {
+ netdev_err(adpt->netdev, "SGMII failed to start\n");
+ return -EIO;
+ }
+
+ /* Disable digital and SERDES loopback */
+ writel(0, phy_regs + SGMII_PHY_LN_BIST_GEN0);
+ writel(0, phy_regs + SGMII_PHY_LN_BIST_GEN2);
+ writel(0, phy_regs + SGMII_PHY_LN_CDR_CTRL1);
+
+ /* Mask out all the SGMII Interrupt */
+ writel(0, phy_regs + EMAC_SGMII_PHY_INTERRUPT_MASK);
+
+ emac_sgmii_irq_clear(adpt, SGMII_PHY_INTERRUPT_ERR);
+
+ return 0;
+}
+
+void emac_sgmii_reset_prepare(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ u32 val;
+
+ /* Reset PHY */
+ val = readl(phy->base + EMAC_EMAC_WRAPPER_CSR2);
+ writel(((val & ~PHY_RESET) | PHY_RESET), phy->base +
+ EMAC_EMAC_WRAPPER_CSR2);
+ /* Ensure phy-reset command is written to HW before the release cmd */
+ msleep(50);
+ val = readl(phy->base + EMAC_EMAC_WRAPPER_CSR2);
+ writel((val & ~PHY_RESET), phy->base + EMAC_EMAC_WRAPPER_CSR2);
+ /* Ensure phy-reset release command is written to HW before initializing
+ * SGMII
+ */
+ msleep(50);
+}
+
+void emac_sgmii_reset(struct emac_adapter *adpt)
+{
+ int ret;
+
+ clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 19200000);
+ emac_sgmii_reset_prepare(adpt);
+
+ ret = adpt->phy.initialize(adpt);
+ if (ret)
+ netdev_err(adpt->netdev,
+ "could not reinitialize internal PHY (error=%i)\n",
+ ret);
+
+ clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 125000000);
+}
+
+static const struct of_device_id emac_sgmii_dt_match[] = {
+ {
+ .compatible = "qcom,fsm9900-emac-sgmii",
+ .data = emac_sgmii_init_v1,
+ },
+ {
+ .compatible = "qcom,qdf2432-emac-sgmii",
+ .data = emac_sgmii_init_v2,
+ },
+ {}
+};
+
+int emac_sgmii_config(struct platform_device *pdev, struct emac_adapter *adpt)
+{
+ struct platform_device *sgmii_pdev = NULL;
+ struct emac_phy *phy = &adpt->phy;
+ struct resource *res;
+ const struct of_device_id *match;
+ struct device_node *np;
+
+ np = of_parse_phandle(pdev->dev.of_node, "internal-phy", 0);
+ if (!np) {
+ dev_err(&pdev->dev, "missing internal-phy property\n");
+ return -ENODEV;
+ }
+
+ sgmii_pdev = of_find_device_by_node(np);
+ if (!sgmii_pdev) {
+ dev_err(&pdev->dev, "invalid internal-phy property\n");
+ return -ENODEV;
+ }
+
+ match = of_match_device(emac_sgmii_dt_match, &sgmii_pdev->dev);
+ if (!match) {
+ dev_err(&pdev->dev, "unrecognized internal phy node\n");
+ return -ENODEV;
+ }
+
+ phy->initialize = match->data;
+
+ /* Base address is the first address */
+ res = platform_get_resource(sgmii_pdev, IORESOURCE_MEM, 0);
+ phy->base = devm_ioremap_resource(&sgmii_pdev->dev, res);
+ if (IS_ERR(phy->base))
+ return PTR_ERR(phy->base);
+
+ /* v2 SGMII has a per-lane digital digital, so parse it if it exists */
+ res = platform_get_resource(sgmii_pdev, IORESOURCE_MEM, 1);
+ if (res) {
+ phy->digital = devm_ioremap_resource(&sgmii_pdev->dev, res);
+ if (IS_ERR(phy->base))
+ return PTR_ERR(phy->base);
+
+ }
+
+ return phy->initialize(adpt);
+}
+
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-sgmii.h b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
new file mode 100644
index 0000000..ce79212
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
@@ -0,0 +1,24 @@
+/* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _EMAC_SGMII_H_
+#define _EMAC_SGMII_H_
+
+struct emac_adapter;
+struct platform_device;
+
+int emac_sgmii_init_v1(struct emac_adapter *adpt);
+int emac_sgmii_init_v2(struct emac_adapter *adpt);
+int emac_sgmii_config(struct platform_device *pdev, struct emac_adapter *adpt);
+void emac_sgmii_reset(struct emac_adapter *adpt);
+
+#endif
diff --git a/drivers/net/ethernet/qualcomm/emac/emac.c b/drivers/net/ethernet/qualcomm/emac/emac.c
new file mode 100644
index 0000000..f0a86f4
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac.c
@@ -0,0 +1,751 @@
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC Gigabit Ethernet Driver */
+
+#include <linux/if_ether.h>
+#include <linux/if_vlan.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_device.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include "emac.h"
+#include "emac-mac.h"
+#include "emac-phy.h"
+#include "emac-sgmii.h"
+
+#define EMAC_MSG_DEFAULT (NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK | \
+ NETIF_MSG_TIMER | NETIF_MSG_IFDOWN | NETIF_MSG_IFUP)
+
+#define EMAC_RRD_SIZE 4
+/* The RRD size if timestamping is enabled: */
+#define EMAC_TS_RRD_SIZE 6
+#define EMAC_TPD_SIZE 4
+#define EMAC_RFD_SIZE 2
+
+#define REG_MAC_RX_STATUS_BIN EMAC_RXMAC_STATC_REG0
+#define REG_MAC_RX_STATUS_END EMAC_RXMAC_STATC_REG22
+#define REG_MAC_TX_STATUS_BIN EMAC_TXMAC_STATC_REG0
+#define REG_MAC_TX_STATUS_END EMAC_TXMAC_STATC_REG24
+
+#define RXQ0_NUM_RFD_PREF_DEF 8
+#define TXQ0_NUM_TPD_PREF_DEF 5
+
+#define EMAC_PREAMBLE_DEF 7
+
+#define DMAR_DLY_CNT_DEF 15
+#define DMAW_DLY_CNT_DEF 4
+
+#define IMR_NORMAL_MASK (\
+ ISR_ERROR |\
+ ISR_GPHY_LINK |\
+ ISR_TX_PKT |\
+ GPHY_WAKEUP_INT)
+
+#define IMR_EXTENDED_MASK (\
+ SW_MAN_INT |\
+ ISR_OVER |\
+ ISR_ERROR |\
+ ISR_GPHY_LINK |\
+ ISR_TX_PKT |\
+ GPHY_WAKEUP_INT)
+
+#define ISR_TX_PKT (\
+ TX_PKT_INT |\
+ TX_PKT_INT1 |\
+ TX_PKT_INT2 |\
+ TX_PKT_INT3)
+
+#define ISR_GPHY_LINK (\
+ GPHY_LINK_UP_INT |\
+ GPHY_LINK_DOWN_INT)
+
+#define ISR_OVER (\
+ RFD0_UR_INT |\
+ RFD1_UR_INT |\
+ RFD2_UR_INT |\
+ RFD3_UR_INT |\
+ RFD4_UR_INT |\
+ RXF_OF_INT |\
+ TXF_UR_INT)
+
+#define ISR_ERROR (\
+ DMAR_TO_INT |\
+ DMAW_TO_INT |\
+ TXQ_TO_INT)
+
+/* in sync with enum emac_clk_id */
+static const char * const emac_clk_name[] = {
+ "axi_clk", "cfg_ahb_clk", "high_speed_clk", "mdio_clk", "tx_clk",
+ "rx_clk", "sys_clk"
+};
+
+void emac_reg_update32(void __iomem *addr, u32 mask, u32 val)
+{
+ u32 data = readl(addr);
+
+ writel(((data & ~mask) | val), addr);
+}
+
+/* reinitialize */
+int emac_reinit_locked(struct emac_adapter *adpt)
+{
+ int ret;
+
+ mutex_lock(&adpt->reset_lock);
+
+ emac_mac_down(adpt);
+ emac_sgmii_reset(adpt);
+ ret = emac_mac_up(adpt);
+
+ mutex_unlock(&adpt->reset_lock);
+
+ return ret;
+}
+
+/* NAPI */
+static int emac_napi_rtx(struct napi_struct *napi, int budget)
+{
+ struct emac_rx_queue *rx_q =
+ container_of(napi, struct emac_rx_queue, napi);
+ struct emac_adapter *adpt = netdev_priv(rx_q->netdev);
+ struct emac_irq *irq = rx_q->irq;
+ int work_done = 0;
+
+ emac_mac_rx_process(adpt, rx_q, &work_done, budget);
+
+ if (work_done < budget) {
+ napi_complete(napi);
+
+ irq->mask |= rx_q->intr;
+ writel(irq->mask, adpt->base + EMAC_INT_MASK);
+ }
+
+ return work_done;
+}
+
+/* Transmit the packet */
+static int emac_start_xmit(struct sk_buff *skb, struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ return emac_mac_tx_buf_send(adpt, &adpt->tx_q, skb);
+}
+
+irqreturn_t emac_isr(int _irq, void *data)
+{
+ struct emac_irq *irq = data;
+ struct emac_adapter *adpt =
+ container_of(irq, struct emac_adapter, irq);
+ struct emac_rx_queue *rx_q = &adpt->rx_q;
+ u32 isr, status;
+
+ /* disable the interrupt */
+ writel(0, adpt->base + EMAC_INT_MASK);
+
+ isr = readl_relaxed(adpt->base + EMAC_INT_STATUS);
+
+ status = isr & irq->mask;
+ if (status == 0)
+ goto exit;
+
+ if (status & ISR_ERROR) {
+ netif_warn(adpt, intr, adpt->netdev,
+ "warning: error irq status 0x%lx\n",
+ status & ISR_ERROR);
+ /* reset MAC */
+ schedule_work(&adpt->work_thread);
+ }
+
+ /* Schedule the napi for receive queue with interrupt
+ * status bit set
+ */
+ if (status & rx_q->intr) {
+ if (napi_schedule_prep(&rx_q->napi)) {
+ irq->mask &= ~rx_q->intr;
+ __napi_schedule(&rx_q->napi);
+ }
+ }
+
+ if (status & TX_PKT_INT)
+ emac_mac_tx_process(adpt, &adpt->tx_q);
+
+ if (status & ISR_OVER)
+ net_warn_ratelimited("warning: TX/RX overflow\n");
+
+ /* link event */
+ if (status & ISR_GPHY_LINK)
+ phy_mac_interrupt(adpt->phydev, !!(status & GPHY_LINK_UP_INT));
+
+exit:
+ /* enable the interrupt */
+ writel(irq->mask, adpt->base + EMAC_INT_MASK);
+
+ return IRQ_HANDLED;
+}
+
+/* Configure VLAN tag strip/insert feature */
+static int emac_set_features(struct net_device *netdev,
+ netdev_features_t features)
+{
+ netdev_features_t changed = features ^ netdev->features;
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ /* We only need to reprogram the hardware if the VLAN tag features
+ * have changed, and if it's already running.
+ */
+ if (!(changed & (NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX)))
+ return 0;
+
+ if (!netif_running(netdev))
+ return 0;
+
+ /* emac_mac_mode_config() uses netdev->features to configure the EMAC,
+ * so make sure it's set first.
+ */
+ netdev->features = features;
+
+ return emac_reinit_locked(adpt);
+}
+
+/* Configure Multicast and Promiscuous modes */
+static void emac_rx_mode_set(struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ struct netdev_hw_addr *ha;
+
+ emac_mac_mode_config(adpt);
+
+ /* update multicast address filtering */
+ emac_mac_multicast_addr_clear(adpt);
+ netdev_for_each_mc_addr(ha, netdev)
+ emac_mac_multicast_addr_set(adpt, ha->addr);
+}
+
+/* Change the Maximum Transfer Unit (MTU) */
+static int emac_change_mtu(struct net_device *netdev, int new_mtu)
+{
+ unsigned int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ if ((max_frame < EMAC_MIN_ETH_FRAME_SIZE) ||
+ (max_frame > EMAC_MAX_ETH_FRAME_SIZE)) {
+ netdev_err(adpt->netdev, "error: invalid MTU setting\n");
+ return -EINVAL;
+ }
+
+ netif_info(adpt, hw, adpt->netdev,
+ "changing MTU from %d to %d\n", netdev->mtu,
+ new_mtu);
+ netdev->mtu = new_mtu;
+
+ if (netif_running(netdev))
+ return emac_reinit_locked(adpt);
+
+ return 0;
+}
+
+/* Called when the network interface is made active */
+static int emac_open(struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ int ret;
+
+ /* allocate rx/tx dma buffer & descriptors */
+ ret = emac_mac_rx_tx_rings_alloc_all(adpt);
+ if (ret) {
+ netdev_err(adpt->netdev, "error allocating rx/tx rings\n");
+ return ret;
+ }
+
+ ret = emac_mac_up(adpt);
+ if (ret) {
+ emac_mac_rx_tx_rings_free_all(adpt);
+ return ret;
+ }
+
+ emac_mac_start(adpt);
+
+ return 0;
+}
+
+/* Called when the network interface is disabled */
+static int emac_close(struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ mutex_lock(&adpt->reset_lock);
+
+ emac_mac_down(adpt);
+ emac_mac_rx_tx_rings_free_all(adpt);
+
+ mutex_unlock(&adpt->reset_lock);
+
+ return 0;
+}
+
+/* Respond to a TX hang */
+static void emac_tx_timeout(struct net_device *netdev)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ schedule_work(&adpt->work_thread);
+}
+
+/* IOCTL support for the interface */
+static int emac_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+{
+ if (!netif_running(netdev))
+ return -EINVAL;
+
+ if (!netdev->phydev)
+ return -ENODEV;
+
+ return phy_mii_ioctl(netdev->phydev, ifr, cmd);
+}
+
+/* Provide network statistics info for the interface */
+static struct rtnl_link_stats64 *emac_get_stats64(struct net_device *netdev,
+ struct rtnl_link_stats64 *net_stats)
+{
+ struct emac_adapter *adpt = netdev_priv(netdev);
+ unsigned int addr = REG_MAC_RX_STATUS_BIN;
+ struct emac_stats *stats = &adpt->stats;
+ u64 *stats_itr = &adpt->stats.rx_ok;
+ u32 val;
+
+ spin_lock(&stats->lock);
+
+ while (addr <= REG_MAC_RX_STATUS_END) {
+ val = readl_relaxed(adpt->base + addr);
+ *stats_itr += val;
+ stats_itr++;
+ addr += sizeof(u32);
+ }
+
+ /* additional rx status */
+ val = readl_relaxed(adpt->base + EMAC_RXMAC_STATC_REG23);
+ adpt->stats.rx_crc_align += val;
+ val = readl_relaxed(adpt->base + EMAC_RXMAC_STATC_REG24);
+ adpt->stats.rx_jubbers += val;
+
+ /* update tx status */
+ addr = REG_MAC_TX_STATUS_BIN;
+ stats_itr = &adpt->stats.tx_ok;
+
+ while (addr <= REG_MAC_TX_STATUS_END) {
+ val = readl_relaxed(adpt->base + addr);
+ *stats_itr += val;
+ ++stats_itr;
+ addr += sizeof(u32);
+ }
+
+ /* additional tx status */
+ val = readl_relaxed(adpt->base + EMAC_TXMAC_STATC_REG25);
+ adpt->stats.tx_col += val;
+
+ /* return parsed statistics */
+ net_stats->rx_packets = stats->rx_ok;
+ net_stats->tx_packets = stats->tx_ok;
+ net_stats->rx_bytes = stats->rx_byte_cnt;
+ net_stats->tx_bytes = stats->tx_byte_cnt;
+ net_stats->multicast = stats->rx_mcast;
+ net_stats->collisions = stats->tx_1_col + stats->tx_2_col * 2 +
+ stats->tx_late_col + stats->tx_abort_col;
+
+ net_stats->rx_errors = stats->rx_frag + stats->rx_fcs_err +
+ stats->rx_len_err + stats->rx_sz_ov +
+ stats->rx_align_err;
+ net_stats->rx_fifo_errors = stats->rx_rxf_ov;
+ net_stats->rx_length_errors = stats->rx_len_err;
+ net_stats->rx_crc_errors = stats->rx_fcs_err;
+ net_stats->rx_frame_errors = stats->rx_align_err;
+ net_stats->rx_over_errors = stats->rx_rxf_ov;
+ net_stats->rx_missed_errors = stats->rx_rxf_ov;
+
+ net_stats->tx_errors = stats->tx_late_col + stats->tx_abort_col +
+ stats->tx_underrun + stats->tx_trunc;
+ net_stats->tx_fifo_errors = stats->tx_underrun;
+ net_stats->tx_aborted_errors = stats->tx_abort_col;
+ net_stats->tx_window_errors = stats->tx_late_col;
+
+ spin_unlock(&stats->lock);
+
+ return net_stats;
+}
+
+static const struct net_device_ops emac_netdev_ops = {
+ .ndo_open = emac_open,
+ .ndo_stop = emac_close,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_start_xmit = emac_start_xmit,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = emac_change_mtu,
+ .ndo_do_ioctl = emac_ioctl,
+ .ndo_tx_timeout = emac_tx_timeout,
+ .ndo_get_stats64 = emac_get_stats64,
+ .ndo_set_features = emac_set_features,
+ .ndo_set_rx_mode = emac_rx_mode_set,
+};
+
+/* Watchdog task routine, called to reinitialize the EMAC */
+static void emac_work_thread(struct work_struct *work)
+{
+ struct emac_adapter *adpt =
+ container_of(work, struct emac_adapter, work_thread);
+
+ emac_reinit_locked(adpt);
+}
+
+/* Initialize various data structures */
+static void emac_init_adapter(struct emac_adapter *adpt)
+{
+ u32 reg;
+
+ /* descriptors */
+ adpt->tx_desc_cnt = EMAC_DEF_TX_DESCS;
+ adpt->rx_desc_cnt = EMAC_DEF_RX_DESCS;
+
+ /* dma */
+ adpt->dma_order = emac_dma_ord_out;
+ adpt->dmar_block = emac_dma_req_4096;
+ adpt->dmaw_block = emac_dma_req_128;
+ adpt->dmar_dly_cnt = DMAR_DLY_CNT_DEF;
+ adpt->dmaw_dly_cnt = DMAW_DLY_CNT_DEF;
+ adpt->tpd_burst = TXQ0_NUM_TPD_PREF_DEF;
+ adpt->rfd_burst = RXQ0_NUM_RFD_PREF_DEF;
+
+ /* irq moderator */
+ reg = ((EMAC_DEF_RX_IRQ_MOD >> 1) << IRQ_MODERATOR2_INIT_SHFT) |
+ ((EMAC_DEF_TX_IRQ_MOD >> 1) << IRQ_MODERATOR_INIT_SHFT);
+ adpt->irq_mod = reg;
+
+ /* others */
+ adpt->preamble = EMAC_PREAMBLE_DEF;
+}
+
+static const u8 duuid[] = {
+ 0x77, 0x79, 0x60, 0xbf,
+ 0x2d, 0xab,
+ 0x9d, 0x4b,
+ 0x94, 0xf0,
+ 0xe1, 0x11, 0x98, 0x01, 0xa2, 0xba
+};
+
+/* Get the clock */
+static int emac_clks_get(struct platform_device *pdev,
+ struct emac_adapter *adpt)
+{
+ unsigned int i;
+
+ for (i = 0; i < EMAC_CLK_CNT; i++) {
+ struct clk *clk = devm_clk_get(&pdev->dev, emac_clk_name[i]);
+
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev,
+ "could not claim clock %s (error=%li)\n",
+ emac_clk_name[i], PTR_ERR(clk));
+
+ return PTR_ERR(clk);
+ }
+
+ adpt->clk[i] = clk;
+ }
+
+ return 0;
+}
+
+/* Initialize clocks */
+static int emac_clks_phase1_init(struct platform_device *pdev,
+ struct emac_adapter *adpt)
+{
+ int ret;
+
+ ret = emac_clks_get(pdev, adpt);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_AXI]);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_CFG_AHB]);
+ if (ret)
+ return ret;
+
+ ret = clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 19200000);
+ if (ret)
+ return ret;
+
+ return clk_prepare_enable(adpt->clk[EMAC_CLK_HIGH_SPEED]);
+}
+
+/* Enable clocks; needs emac_clks_phase1_init to be called before */
+static int emac_clks_phase2_init(struct platform_device *pdev,
+ struct emac_adapter *adpt)
+{
+ int ret;
+
+ ret = clk_set_rate(adpt->clk[EMAC_CLK_TX], 125000000);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_TX]);
+ if (ret)
+ return ret;
+
+ ret = clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 125000000);
+ if (ret)
+ return ret;
+
+ ret = clk_set_rate(adpt->clk[EMAC_CLK_MDIO], 25000000);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_MDIO]);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(adpt->clk[EMAC_CLK_RX]);
+ if (ret)
+ return ret;
+
+ return clk_prepare_enable(adpt->clk[EMAC_CLK_SYS]);
+}
+
+static void emac_clks_teardown(struct emac_adapter *adpt)
+{
+
+ unsigned int i;
+
+ for (i = 0; i < EMAC_CLK_CNT; i++)
+ clk_disable_unprepare(adpt->clk[i]);
+}
+
+/* Get the resources */
+static int emac_probe_resources(struct platform_device *pdev,
+ struct emac_adapter *adpt)
+{
+ struct device_node *node = pdev->dev.of_node;
+ struct net_device *netdev = adpt->netdev;
+ struct resource *res;
+ const void *maddr;
+ int ret = 0;
+
+ /* get mac address */
+ maddr = of_get_mac_address(node);
+ if (!maddr)
+ eth_hw_addr_random(netdev);
+ else
+ ether_addr_copy(netdev->dev_addr, maddr);
+
+ /* Core 0 interrupt */
+ ret = platform_get_irq(pdev, 0);
+ if (ret < 0) {
+ dev_err(&pdev->dev,
+ "error: missing core0 irq resource (error=%i)\n", ret);
+ return ret;
+ }
+ adpt->irq.irq = ret;
+
+ /* base register address */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ adpt->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(adpt->base))
+ return PTR_ERR(adpt->base);
+
+ /* CSR register address */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ adpt->csr = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(adpt->csr))
+ return PTR_ERR(adpt->csr);
+
+ netdev->base_addr = (unsigned long)adpt->base;
+
+ return 0;
+}
+
+static const struct of_device_id emac_dt_match[] = {
+ {
+ .compatible = "qcom,fsm9900-emac",
+ },
+ {}
+};
+
+static int emac_probe(struct platform_device *pdev)
+{
+ struct net_device *netdev;
+ struct emac_adapter *adpt;
+ struct emac_phy *phy;
+ u16 devid, revid;
+ u32 reg;
+ int ret;
+
+ /* The EMAC itself is capable of 64-bit DMA, so try that first. */
+ ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+ if (ret) {
+ /* Some platforms may restrict the EMAC's address bus to less
+ * then the size of DDR. In this case, we need to try a
+ * smaller mask. We could try every possible smaller mask,
+ * but that's overkill. Instead, just fall to 32-bit, which
+ * should always work.
+ */
+ ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+ if (ret) {
+ dev_err(&pdev->dev, "could not set DMA mask\n");
+ return ret;
+ }
+ }
+
+ netdev = alloc_etherdev(sizeof(struct emac_adapter));
+ if (!netdev)
+ return -ENOMEM;
+
+ dev_set_drvdata(&pdev->dev, netdev);
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ adpt = netdev_priv(netdev);
+ adpt->netdev = netdev;
+ adpt->msg_enable = EMAC_MSG_DEFAULT;
+
+ phy = &adpt->phy;
+
+ mutex_init(&adpt->reset_lock);
+ spin_lock_init(&adpt->stats.lock);
+
+ adpt->irq.mask = RX_PKT_INT0 | IMR_NORMAL_MASK;
+
+ ret = emac_probe_resources(pdev, adpt);
+ if (ret)
+ goto err_undo_netdev;
+
+ /* initialize clocks */
+ ret = emac_clks_phase1_init(pdev, adpt);
+ if (ret) {
+ dev_err(&pdev->dev, "could not initialize clocks\n");
+ goto err_undo_netdev;
+ }
+
+ netdev->watchdog_timeo = EMAC_WATCHDOG_TIME;
+ netdev->irq = adpt->irq.irq;
+
+ adpt->rrd_size = EMAC_RRD_SIZE;
+ adpt->tpd_size = EMAC_TPD_SIZE;
+ adpt->rfd_size = EMAC_RFD_SIZE;
+
+ netdev->netdev_ops = &emac_netdev_ops;
+
+ emac_init_adapter(adpt);
+
+ /* init external phy */
+ ret = emac_phy_config(pdev, adpt);
+ if (ret)
+ goto err_undo_clocks;
+
+ /* init internal sgmii phy */
+ ret = emac_sgmii_config(pdev, adpt);
+ if (ret)
+ goto err_undo_mdiobus;
+
+ /* enable clocks */
+ ret = emac_clks_phase2_init(pdev, adpt);
+ if (ret) {
+ dev_err(&pdev->dev, "could not initialize clocks\n");
+ goto err_undo_mdiobus;
+ }
+
+ emac_mac_reset(adpt);
+
+ /* set hw features */
+ netdev->features = NETIF_F_SG | NETIF_F_HW_CSUM | NETIF_F_RXCSUM |
+ NETIF_F_TSO | NETIF_F_TSO6 | NETIF_F_HW_VLAN_CTAG_RX |
+ NETIF_F_HW_VLAN_CTAG_TX;
+ netdev->hw_features = netdev->features;
+
+ netdev->vlan_features |= NETIF_F_SG | NETIF_F_HW_CSUM |
+ NETIF_F_TSO | NETIF_F_TSO6;
+
+ INIT_WORK(&adpt->work_thread, emac_work_thread);
+
+ /* Initialize queues */
+ emac_mac_rx_tx_ring_init_all(pdev, adpt);
+
+ netif_napi_add(netdev, &adpt->rx_q.napi, emac_napi_rtx,
+ NAPI_POLL_WEIGHT);
+
+ ret = register_netdev(netdev);
+ if (ret) {
+ dev_err(&pdev->dev, "could not register net device\n");
+ goto err_undo_napi;
+ }
+
+ reg = readl_relaxed(adpt->base + EMAC_DMA_MAS_CTRL);
+ devid = (reg & DEV_ID_NUM_BMSK) >> DEV_ID_NUM_SHFT;
+ revid = (reg & DEV_REV_NUM_BMSK) >> DEV_REV_NUM_SHFT;
+ reg = readl_relaxed(adpt->base + EMAC_CORE_HW_VERSION);
+
+ netif_info(adpt, probe, netdev,
+ "hardware id %d.%d, hardware version %d.%d.%d\n",
+ devid, revid,
+ (reg & MAJOR_BMSK) >> MAJOR_SHFT,
+ (reg & MINOR_BMSK) >> MINOR_SHFT,
+ (reg & STEP_BMSK) >> STEP_SHFT);
+
+ return 0;
+
+err_undo_napi:
+ netif_napi_del(&adpt->rx_q.napi);
+err_undo_mdiobus:
+ mdiobus_unregister(adpt->mii_bus);
+err_undo_clocks:
+ emac_clks_teardown(adpt);
+err_undo_netdev:
+ free_netdev(netdev);
+
+ return ret;
+}
+
+static int emac_remove(struct platform_device *pdev)
+{
+ struct net_device *netdev = dev_get_drvdata(&pdev->dev);
+ struct emac_adapter *adpt = netdev_priv(netdev);
+
+ unregister_netdev(netdev);
+ netif_napi_del(&adpt->rx_q.napi);
+
+ emac_clks_teardown(adpt);
+
+ mdiobus_unregister(adpt->mii_bus);
+ free_netdev(netdev);
+ dev_set_drvdata(&pdev->dev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver emac_platform_driver = {
+ .probe = emac_probe,
+ .remove = emac_remove,
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "qcom-emac",
+ .of_match_table = emac_dt_match,
+ },
+};
+
+module_platform_driver(emac_platform_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:qcom-emac");
diff --git a/drivers/net/ethernet/qualcomm/emac/emac.h b/drivers/net/ethernet/qualcomm/emac/emac.h
new file mode 100644
index 0000000..5078a33
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac.h
@@ -0,0 +1,335 @@
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _EMAC_H_
+#define _EMAC_H_
+
+#include <linux/irqreturn.h>
+#include <linux/netdevice.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+#include "emac-mac.h"
+#include "emac-phy.h"
+
+/* EMAC base register offsets */
+#define EMAC_DMA_MAS_CTRL 0x001400
+#define EMAC_IRQ_MOD_TIM_INIT 0x001408
+#define EMAC_BLK_IDLE_STS 0x00140c
+#define EMAC_PHY_LINK_DELAY 0x00141c
+#define EMAC_SYS_ALIV_CTRL 0x001434
+#define EMAC_MAC_IPGIFG_CTRL 0x001484
+#define EMAC_MAC_STA_ADDR0 0x001488
+#define EMAC_MAC_STA_ADDR1 0x00148c
+#define EMAC_HASH_TAB_REG0 0x001490
+#define EMAC_HASH_TAB_REG1 0x001494
+#define EMAC_MAC_HALF_DPLX_CTRL 0x001498
+#define EMAC_MAX_FRAM_LEN_CTRL 0x00149c
+#define EMAC_INT_STATUS 0x001600
+#define EMAC_INT_MASK 0x001604
+#define EMAC_RXMAC_STATC_REG0 0x001700
+#define EMAC_RXMAC_STATC_REG22 0x001758
+#define EMAC_TXMAC_STATC_REG0 0x001760
+#define EMAC_TXMAC_STATC_REG24 0x0017c0
+#define EMAC_CORE_HW_VERSION 0x001974
+#define EMAC_IDT_TABLE0 0x001b00
+#define EMAC_RXMAC_STATC_REG23 0x001bc8
+#define EMAC_RXMAC_STATC_REG24 0x001bcc
+#define EMAC_TXMAC_STATC_REG25 0x001bd0
+#define EMAC_INT1_MASK 0x001bf0
+#define EMAC_INT1_STATUS 0x001bf4
+#define EMAC_INT2_MASK 0x001bf8
+#define EMAC_INT2_STATUS 0x001bfc
+#define EMAC_INT3_MASK 0x001c00
+#define EMAC_INT3_STATUS 0x001c04
+
+/* EMAC_DMA_MAS_CTRL */
+#define DEV_ID_NUM_BMSK 0x7f000000
+#define DEV_ID_NUM_SHFT 24
+#define DEV_REV_NUM_BMSK 0xff0000
+#define DEV_REV_NUM_SHFT 16
+#define INT_RD_CLR_EN 0x4000
+#define IRQ_MODERATOR2_EN 0x800
+#define IRQ_MODERATOR_EN 0x400
+#define LPW_CLK_SEL 0x80
+#define LPW_STATE 0x20
+#define LPW_MODE 0x10
+#define SOFT_RST 0x1
+
+/* EMAC_IRQ_MOD_TIM_INIT */
+#define IRQ_MODERATOR2_INIT_BMSK 0xffff0000
+#define IRQ_MODERATOR2_INIT_SHFT 16
+#define IRQ_MODERATOR_INIT_BMSK 0xffff
+#define IRQ_MODERATOR_INIT_SHFT 0
+
+/* EMAC_INT_STATUS */
+#define DIS_INT BIT(31)
+#define PTP_INT BIT(30)
+#define RFD4_UR_INT BIT(29)
+#define TX_PKT_INT3 BIT(26)
+#define TX_PKT_INT2 BIT(25)
+#define TX_PKT_INT1 BIT(24)
+#define RX_PKT_INT3 BIT(19)
+#define RX_PKT_INT2 BIT(18)
+#define RX_PKT_INT1 BIT(17)
+#define RX_PKT_INT0 BIT(16)
+#define TX_PKT_INT BIT(15)
+#define TXQ_TO_INT BIT(14)
+#define GPHY_WAKEUP_INT BIT(13)
+#define GPHY_LINK_DOWN_INT BIT(12)
+#define GPHY_LINK_UP_INT BIT(11)
+#define DMAW_TO_INT BIT(10)
+#define DMAR_TO_INT BIT(9)
+#define TXF_UR_INT BIT(8)
+#define RFD3_UR_INT BIT(7)
+#define RFD2_UR_INT BIT(6)
+#define RFD1_UR_INT BIT(5)
+#define RFD0_UR_INT BIT(4)
+#define RXF_OF_INT BIT(3)
+#define SW_MAN_INT BIT(2)
+
+/* EMAC_MAILBOX_6 */
+#define RFD2_PROC_IDX_BMSK 0xfff0000
+#define RFD2_PROC_IDX_SHFT 16
+#define RFD2_PROD_IDX_BMSK 0xfff
+#define RFD2_PROD_IDX_SHFT 0
+
+/* EMAC_CORE_HW_VERSION */
+#define MAJOR_BMSK 0xf0000000
+#define MAJOR_SHFT 28
+#define MINOR_BMSK 0xfff0000
+#define MINOR_SHFT 16
+#define STEP_BMSK 0xffff
+#define STEP_SHFT 0
+
+/* EMAC_EMAC_WRAPPER_CSR1 */
+#define TX_INDX_FIFO_SYNC_RST BIT(23)
+#define TX_TS_FIFO_SYNC_RST BIT(22)
+#define RX_TS_FIFO2_SYNC_RST BIT(21)
+#define RX_TS_FIFO1_SYNC_RST BIT(20)
+#define TX_TS_ENABLE BIT(16)
+#define DIS_1588_CLKS BIT(11)
+#define FREQ_MODE BIT(9)
+#define ENABLE_RRD_TIMESTAMP BIT(3)
+
+/* EMAC_EMAC_WRAPPER_CSR2 */
+#define HDRIVE_BMSK 0x3000
+#define HDRIVE_SHFT 12
+#define SLB_EN BIT(9)
+#define PLB_EN BIT(8)
+#define WOL_EN BIT(3)
+#define PHY_RESET BIT(0)
+
+#define EMAC_DEV_ID 0x0040
+
+/* SGMII v2 per lane registers */
+#define SGMII_LN_RSM_START 0x029C
+
+/* SGMII v2 PHY common registers */
+#define SGMII_PHY_CMN_CTRL 0x0408
+#define SGMII_PHY_CMN_RESET_CTRL 0x0410
+
+/* SGMII v2 PHY registers per lane */
+#define SGMII_PHY_LN_OFFSET 0x0400
+#define SGMII_PHY_LN_LANE_STATUS 0x00DC
+#define SGMII_PHY_LN_BIST_GEN0 0x008C
+#define SGMII_PHY_LN_BIST_GEN1 0x0090
+#define SGMII_PHY_LN_BIST_GEN2 0x0094
+#define SGMII_PHY_LN_BIST_GEN3 0x0098
+#define SGMII_PHY_LN_CDR_CTRL1 0x005C
+
+enum emac_clk_id {
+ EMAC_CLK_AXI,
+ EMAC_CLK_CFG_AHB,
+ EMAC_CLK_HIGH_SPEED,
+ EMAC_CLK_MDIO,
+ EMAC_CLK_TX,
+ EMAC_CLK_RX,
+ EMAC_CLK_SYS,
+ EMAC_CLK_CNT
+};
+
+#define EMAC_LINK_SPEED_UNKNOWN 0x0
+#define EMAC_LINK_SPEED_10_HALF BIT(0)
+#define EMAC_LINK_SPEED_10_FULL BIT(1)
+#define EMAC_LINK_SPEED_100_HALF BIT(2)
+#define EMAC_LINK_SPEED_100_FULL BIT(3)
+#define EMAC_LINK_SPEED_1GB_FULL BIT(5)
+
+#define EMAC_MAX_SETUP_LNK_CYCLE 100
+
+/* Wake On Lan */
+#define EMAC_WOL_PHY 0x00000001 /* PHY Status Change */
+#define EMAC_WOL_MAGIC 0x00000002 /* Magic Packet */
+
+struct emac_stats {
+ /* rx */
+ u64 rx_ok; /* good packets */
+ u64 rx_bcast; /* good broadcast packets */
+ u64 rx_mcast; /* good multicast packets */
+ u64 rx_pause; /* pause packet */
+ u64 rx_ctrl; /* control packets other than pause frame. */
+ u64 rx_fcs_err; /* packets with bad FCS. */
+ u64 rx_len_err; /* packets with length mismatch */
+ u64 rx_byte_cnt; /* good bytes count (without FCS) */
+ u64 rx_runt; /* runt packets */
+ u64 rx_frag; /* fragment count */
+ u64 rx_sz_64; /* packets that are 64 bytes */
+ u64 rx_sz_65_127; /* packets that are 65-127 bytes */
+ u64 rx_sz_128_255; /* packets that are 128-255 bytes */
+ u64 rx_sz_256_511; /* packets that are 256-511 bytes */
+ u64 rx_sz_512_1023; /* packets that are 512-1023 bytes */
+ u64 rx_sz_1024_1518; /* packets that are 1024-1518 bytes */
+ u64 rx_sz_1519_max; /* packets that are 1519-MTU bytes*/
+ u64 rx_sz_ov; /* packets that are >MTU bytes (truncated) */
+ u64 rx_rxf_ov; /* packets dropped due to RX FIFO overflow */
+ u64 rx_align_err; /* alignment errors */
+ u64 rx_bcast_byte_cnt; /* broadcast packets byte count (without FCS) */
+ u64 rx_mcast_byte_cnt; /* multicast packets byte count (without FCS) */
+ u64 rx_err_addr; /* packets dropped due to address filtering */
+ u64 rx_crc_align; /* CRC align errors */
+ u64 rx_jubbers; /* jubbers */
+
+ /* tx */
+ u64 tx_ok; /* good packets */
+ u64 tx_bcast; /* good broadcast packets */
+ u64 tx_mcast; /* good multicast packets */
+ u64 tx_pause; /* pause packets */
+ u64 tx_exc_defer; /* packets with excessive deferral */
+ u64 tx_ctrl; /* control packets other than pause frame */
+ u64 tx_defer; /* packets that are deferred. */
+ u64 tx_byte_cnt; /* good bytes count (without FCS) */
+ u64 tx_sz_64; /* packets that are 64 bytes */
+ u64 tx_sz_65_127; /* packets that are 65-127 bytes */
+ u64 tx_sz_128_255; /* packets that are 128-255 bytes */
+ u64 tx_sz_256_511; /* packets that are 256-511 bytes */
+ u64 tx_sz_512_1023; /* packets that are 512-1023 bytes */
+ u64 tx_sz_1024_1518; /* packets that are 1024-1518 bytes */
+ u64 tx_sz_1519_max; /* packets that are 1519-MTU bytes */
+ u64 tx_1_col; /* packets single prior collision */
+ u64 tx_2_col; /* packets with multiple prior collisions */
+ u64 tx_late_col; /* packets with late collisions */
+ u64 tx_abort_col; /* packets aborted due to excess collisions */
+ u64 tx_underrun; /* packets aborted due to FIFO underrun */
+ u64 tx_rd_eop; /* count of reads beyond EOP */
+ u64 tx_len_err; /* packets with length mismatch */
+ u64 tx_trunc; /* packets truncated due to size >MTU */
+ u64 tx_bcast_byte; /* broadcast packets byte count (without FCS) */
+ u64 tx_mcast_byte; /* multicast packets byte count (without FCS) */
+ u64 tx_col; /* collisions */
+
+ spinlock_t lock; /* prevent multiple simultaneous readers */
+};
+
+/* RSS hstype Definitions */
+#define EMAC_RSS_HSTYP_IPV4_EN 0x00000001
+#define EMAC_RSS_HSTYP_TCP4_EN 0x00000002
+#define EMAC_RSS_HSTYP_IPV6_EN 0x00000004
+#define EMAC_RSS_HSTYP_TCP6_EN 0x00000008
+#define EMAC_RSS_HSTYP_ALL_EN (\
+ EMAC_RSS_HSTYP_IPV4_EN |\
+ EMAC_RSS_HSTYP_TCP4_EN |\
+ EMAC_RSS_HSTYP_IPV6_EN |\
+ EMAC_RSS_HSTYP_TCP6_EN)
+
+#define EMAC_VLAN_TO_TAG(_vlan, _tag) \
+ (_tag = ((((_vlan) >> 8) & 0xFF) | (((_vlan) & 0xFF) << 8)))
+
+#define EMAC_TAG_TO_VLAN(_tag, _vlan) \
+ (_vlan = ((((_tag) >> 8) & 0xFF) | (((_tag) & 0xFF) << 8)))
+
+#define EMAC_DEF_RX_BUF_SIZE 1536
+#define EMAC_MAX_JUMBO_PKT_SIZE (9 * 1024)
+#define EMAC_MAX_TX_OFFLOAD_THRESH (9 * 1024)
+
+#define EMAC_MAX_ETH_FRAME_SIZE EMAC_MAX_JUMBO_PKT_SIZE
+#define EMAC_MIN_ETH_FRAME_SIZE 68
+
+#define EMAC_DEF_TX_QUEUES 1
+#define EMAC_DEF_RX_QUEUES 1
+
+#define EMAC_MIN_TX_DESCS 128
+#define EMAC_MIN_RX_DESCS 128
+
+#define EMAC_MAX_TX_DESCS 16383
+#define EMAC_MAX_RX_DESCS 2047
+
+#define EMAC_DEF_TX_DESCS 512
+#define EMAC_DEF_RX_DESCS 256
+
+#define EMAC_DEF_RX_IRQ_MOD 250
+#define EMAC_DEF_TX_IRQ_MOD 250
+
+#define EMAC_WATCHDOG_TIME (5 * HZ)
+
+/* by default check link every 4 seconds */
+#define EMAC_TRY_LINK_TIMEOUT (4 * HZ)
+
+/* emac_irq per-device (per-adapter) irq properties.
+ * @irq: irq number.
+ * @mask mask to use over status register.
+ */
+struct emac_irq {
+ unsigned int irq;
+ u32 mask;
+};
+
+/* The device's main data structure */
+struct emac_adapter {
+ struct net_device *netdev;
+ struct mii_bus *mii_bus;
+ struct phy_device *phydev;
+
+ void __iomem *base;
+ void __iomem *csr;
+
+ struct emac_phy phy;
+ struct emac_stats stats;
+
+ struct emac_irq irq;
+ struct clk *clk[EMAC_CLK_CNT];
+
+ /* All Descriptor memory */
+ struct emac_ring_header ring_header;
+ struct emac_tx_queue tx_q;
+ struct emac_rx_queue rx_q;
+ unsigned int tx_desc_cnt;
+ unsigned int rx_desc_cnt;
+ unsigned int rrd_size; /* in quad words */
+ unsigned int rfd_size; /* in quad words */
+ unsigned int tpd_size; /* in quad words */
+
+ unsigned int rxbuf_size;
+
+ /* Ring parameter */
+ u8 tpd_burst;
+ u8 rfd_burst;
+ unsigned int dmaw_dly_cnt;
+ unsigned int dmar_dly_cnt;
+ enum emac_dma_req_block dmar_block;
+ enum emac_dma_req_block dmaw_block;
+ enum emac_dma_order dma_order;
+
+ u32 irq_mod;
+ u32 preamble;
+
+ struct work_struct work_thread;
+
+ u16 msg_enable;
+
+ struct mutex reset_lock;
+};
+
+int emac_reinit_locked(struct emac_adapter *adpt);
+void emac_reg_update32(void __iomem *addr, u32 mask, u32 val);
+irqreturn_t emac_isr(int irq, void *data);
+
+#endif /* _EMAC_H_ */
--
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc. Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-25 21:39 [PATCH] [v9] net: emac: emac gigabit ethernet controller driver Timur Tabi
@ 2016-08-27 4:29 ` David Miller
2016-08-27 12:26 ` Timur Tabi
2016-08-27 20:26 ` Rami Rosen
[not found] ` <1472161143-26417-1-git-send-email-timur-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2 siblings, 1 reply; 17+ messages in thread
From: David Miller @ 2016-08-27 4:29 UTC (permalink / raw)
To: timur
Cc: netdev, devicetree, linux-arm-msm, sdharia, shankerd, vikrams,
cov, gavidov, robh+dt, andrew, bjorn.andersson, mlangsdo, jcm,
agross, f.fainelli, LinoSanfilippo
From: Timur Tabi <timur@codeaurora.org>
Date: Thu, 25 Aug 2016 16:39:03 -0500
> +static const u8 duuid[] = {
> + 0x77, 0x79, 0x60, 0xbf,
> + 0x2d, 0xab,
> + 0x9d, 0x4b,
> + 0x94, 0xf0,
> + 0xe1, 0x11, 0x98, 0x01, 0xa2, 0xba
> +};
This seems to be completely unused, please remove it.
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-27 4:29 ` David Miller
@ 2016-08-27 12:26 ` Timur Tabi
2016-08-27 17:58 ` Florian Fainelli
2016-08-28 4:50 ` David Miller
0 siblings, 2 replies; 17+ messages in thread
From: Timur Tabi @ 2016-08-27 12:26 UTC (permalink / raw)
To: David Miller
Cc: netdev, devicetree, linux-arm-msm, sdharia, shankerd, vikrams,
cov, gavidov, robh+dt, andrew, bjorn.andersson, mlangsdo, jcm,
agross, f.fainelli, LinoSanfilippo
David Miller wrote:
> From: Timur Tabi <timur@codeaurora.org>
> Date: Thu, 25 Aug 2016 16:39:03 -0500
>
>> +static const u8 duuid[] = {
>> + 0x77, 0x79, 0x60, 0xbf,
>> + 0x2d, 0xab,
>> + 0x9d, 0x4b,
>> + 0x94, 0xf0,
>> + 0xe1, 0x11, 0x98, 0x01, 0xa2, 0xba
>> +};
>
> This seems to be completely unused, please remove it.
Sorry, I missed that during my cleanup. I'll remove it in v10.
I wonder why my compiler didn't complain about the unused static.
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the
Code Aurora Forum, hosted by The Linux Foundation.
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-27 12:26 ` Timur Tabi
@ 2016-08-27 17:58 ` Florian Fainelli
2016-08-28 4:50 ` David Miller
1 sibling, 0 replies; 17+ messages in thread
From: Florian Fainelli @ 2016-08-27 17:58 UTC (permalink / raw)
To: Timur Tabi, David Miller
Cc: netdev, devicetree, linux-arm-msm, sdharia, shankerd, vikrams,
cov, gavidov, robh+dt, andrew, bjorn.andersson, mlangsdo, jcm,
agross, LinoSanfilippo
On August 27, 2016 5:26:39 AM PDT, Timur Tabi <timur@codeaurora.org> wrote:
>David Miller wrote:
>> From: Timur Tabi <timur@codeaurora.org>
>> Date: Thu, 25 Aug 2016 16:39:03 -0500
>>
>>> +static const u8 duuid[] = {
>>> + 0x77, 0x79, 0x60, 0xbf,
>>> + 0x2d, 0xab,
>>> + 0x9d, 0x4b,
>>> + 0x94, 0xf0,
>>> + 0xe1, 0x11, 0x98, 0x01, 0xa2, 0xba
>>> +};
>>
>> This seems to be completely unused, please remove it.
>
>Sorry, I missed that during my cleanup. I'll remove it in v10.
>
>I wonder why my compiler didn't complain about the unused static.
AFAICT this really depends on how modern your compiler is and which warnings it may now enable by default.
Since you are very close from an accepted driver, you may want to squash potential warnings (and more) with doing a sparse build (make C=) which covers a bit more than what a traditional C compiler does.
Almost there!
--
Florian
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-25 21:39 [PATCH] [v9] net: emac: emac gigabit ethernet controller driver Timur Tabi
2016-08-27 4:29 ` David Miller
@ 2016-08-27 20:26 ` Rami Rosen
[not found] ` <CAKoUAr=Z56VxzW=zHu7r9ossdXHQ6xpeYdR5jwhv38zkV_eKFQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
[not found] ` <1472161143-26417-1-git-send-email-timur-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2 siblings, 1 reply; 17+ messages in thread
From: Rami Rosen @ 2016-08-27 20:26 UTC (permalink / raw)
To: Timur Tabi
Cc: Netdev, devicetree, linux-arm-msm, sdharia, shankerd, vikrams,
cov, gavidov, robh+dt, andrew, bjorn.andersson, mlangsdo, jcm,
agross, David Miller, Florian Fainelli, LinoSanfilippo
Hi,
Shouldn't it be obj-$(CONFIG_QCOM_EMAC) instead obj-y? QCOM_EMAC is defined as
tristate in the drivers/net/ethernet/qualcomm/Kconfig by this patch,
so it should be possible to build it as a *.ko module also.
> diff --git a/drivers/net/ethernet/qualcomm/emac/Makefile b/drivers/net/ethernet/qualcomm/emac/Makefile
> new file mode 100644
> index 0000000..700ee6e
> --- /dev/null
> +++ b/drivers/net/ethernet/qualcomm/emac/Makefile
> @@ -0,0 +1,7 @@
> +#
> +# Makefile for the Qualcomm Technologies, Inc. EMAC Gigabit Ethernet driver
> +#
> +
> +obj-y += qcom-emac.o
> +
The return type of the method emac_tx_tpd_create() should be void, as
it always returns true.
> +/* Produce new transmit descriptor */
> +static bool emac_tx_tpd_create(struct emac_adapter *adpt,
> + struct emac_tx_queue *tx_q, struct emac_tpd *tpd)
> +{
> + u32 *hw_tpd;
> +
> + tx_q->tpd.last_produce_idx = tx_q->tpd.produce_idx;
> + hw_tpd = EMAC_TPD(tx_q, adpt->tpd_size, tx_q->tpd.produce_idx);
> +
> + if (++tx_q->tpd.produce_idx == tx_q->tpd.count)
> + tx_q->tpd.produce_idx = 0;
> +
> + *(hw_tpd++) = tpd->word[0];
> + *(hw_tpd++) = tpd->word[1];
> + *(hw_tpd++) = tpd->word[2];
> + *hw_tpd = tpd->word[3];
> +
> + return true;
> +}
...
...
...
Seems that there are several unused members in the emac_stats struct:
> +struct emac_stats {
...
...
Both rx_bcast_byte_cnt and rx_mcast_byte_cnt are not used anywhere/
> + u64 rx_bcast_byte_cnt; /* broadcast packets byte count (without FCS) */
> + u64 rx_mcast_byte_cnt; /* multicast packets byte count (without FCS) */
...
rx_err_addr is not used
> + u64 rx_err_addr; /* packets dropped due to address filtering */
Typo: it is jabbers and not jubbers; greppping for "jubber" under
drivers/net/ethernet gives
0 results, whereas:
/net-next/drivers/net/ethernet$ grep -R jabber | wc -l
gives 241 results.
> + u64 rx_jubbers; /* jubbers */
...
..
tx_rd_eop and tx_len_err are not used
> + u64 tx_rd_eop; /* count of reads beyond EOP */
> + u64 tx_len_err; /* packets with length mismatch */
Both tx_bcast_byte and tx_mcast_byte are not used.
> + u64 tx_bcast_byte; /* broadcast packets byte count (without FCS) */
> + u64 tx_mcast_byte; /* multicast packets byte count (without FCS) */
Thanks for your good work, it seems that the driver is almost done!
Regards,
Rami Rosen
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
[not found] ` <CAKoUAr=Z56VxzW=zHu7r9ossdXHQ6xpeYdR5jwhv38zkV_eKFQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
@ 2016-08-27 20:42 ` Timur Tabi
2016-08-31 18:57 ` Timur Tabi
0 siblings, 1 reply; 17+ messages in thread
From: Timur Tabi @ 2016-08-27 20:42 UTC (permalink / raw)
To: Rami Rosen
Cc: Netdev, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
sdharia-sgV2jX0FEOL9JmXXK+q4OQ, shankerd-sgV2jX0FEOL9JmXXK+q4OQ,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, cov-sgV2jX0FEOL9JmXXK+q4OQ,
gavidov-sgV2jX0FEOL9JmXXK+q4OQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
andrew-g2DYL2Zd6BY, bjorn.andersson-QSEj5FYQhm4dnm+yROfE0A,
mlangsdo-H+wXaHxf7aLQT0dZR+AlfA, jcm-H+wXaHxf7aLQT0dZR+AlfA,
agross-sgV2jX0FEOL9JmXXK+q4OQ, David Miller, Florian Fainelli,
LinoSanfilippo-Mmb7MZpHnFY
Rami Rosen wrote:
> Hi,
>
> Shouldn't it be obj-$(CONFIG_QCOM_EMAC) instead obj-y?
Yes, I noticed this soon after I posted this patch. I will fix it in v10.
> The return type of the method emac_tx_tpd_create() should be void, as
> it always returns true.
Will fix, thanks.
> Seems that there are several unused members in the emac_stats struct:
>
>> +struct emac_stats {
> ...
> ...
> Both rx_bcast_byte_cnt and rx_mcast_byte_cnt are not used anywhere/
>> + u64 rx_bcast_byte_cnt; /* broadcast packets byte count (without FCS) */
>> + u64 rx_mcast_byte_cnt; /* multicast packets byte count (without FCS) */
> ...
> rx_err_addr is not used
>> + u64 rx_err_addr; /* packets dropped due to address filtering */
I'll go through the structure and remove the unused fields.
>
> Typo: it is jabbers and not jubbers; greppping for "jubber" under
> drivers/net/ethernet gives
> 0 results, whereas:
> /net-next/drivers/net/ethernet$ grep -R jabber | wc -l
> gives 241 results.
>
>> + u64 rx_jubbers; /* jubbers */
Thanks. I'll fix that in v10.
>
>
> ...
> ..
> tx_rd_eop and tx_len_err are not used
>> + u64 tx_rd_eop; /* count of reads beyond EOP */
>> + u64 tx_len_err; /* packets with length mismatch */
>
> Both tx_bcast_byte and tx_mcast_byte are not used.
>> + u64 tx_bcast_byte; /* broadcast packets byte count (without FCS) */
>> + u64 tx_mcast_byte; /* multicast packets byte count (without FCS) */
>
> Thanks for your good work, it seems that the driver is almost done!
I'm grateful for the opportunity to improve this driver over the crappy
one that's been bouncing around internally for years, and for all the
people who helped me along the way.
--
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc. Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-27 12:26 ` Timur Tabi
2016-08-27 17:58 ` Florian Fainelli
@ 2016-08-28 4:50 ` David Miller
1 sibling, 0 replies; 17+ messages in thread
From: David Miller @ 2016-08-28 4:50 UTC (permalink / raw)
To: timur
Cc: netdev, devicetree, linux-arm-msm, sdharia, shankerd, vikrams,
cov, gavidov, robh+dt, andrew, bjorn.andersson, mlangsdo, jcm,
agross, f.fainelli, LinoSanfilippo
From: Timur Tabi <timur@codeaurora.org>
Date: Sat, 27 Aug 2016 07:26:39 -0500
> David Miller wrote:
>> From: Timur Tabi <timur@codeaurora.org>
>> Date: Thu, 25 Aug 2016 16:39:03 -0500
>>
>>> +static const u8 duuid[] = {
>>> + 0x77, 0x79, 0x60, 0xbf,
>>> + 0x2d, 0xab,
>>> + 0x9d, 0x4b,
>>> + 0x94, 0xf0,
>>> + 0xe1, 0x11, 0x98, 0x01, 0xa2, 0xba
>>> +};
>>
>> This seems to be completely unused, please remove it.
>
> Sorry, I missed that during my cleanup. I'll remove it in v10.
>
> I wonder why my compiler didn't complain about the unused static.
Unused static "const" is not warned about.
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
[not found] ` <1472161143-26417-1-git-send-email-timur-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2016-08-31 15:00 ` Rob Herring
2016-08-31 15:11 ` Timur Tabi
2016-08-31 15:24 ` Andrew Lunn
0 siblings, 2 replies; 17+ messages in thread
From: Rob Herring @ 2016-08-31 15:00 UTC (permalink / raw)
To: Timur Tabi
Cc: netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
sdharia-sgV2jX0FEOL9JmXXK+q4OQ, shankerd-sgV2jX0FEOL9JmXXK+q4OQ,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, cov-sgV2jX0FEOL9JmXXK+q4OQ,
gavidov-sgV2jX0FEOL9JmXXK+q4OQ, andrew-g2DYL2Zd6BY,
bjorn.andersson-QSEj5FYQhm4dnm+yROfE0A,
mlangsdo-H+wXaHxf7aLQT0dZR+AlfA, jcm-H+wXaHxf7aLQT0dZR+AlfA,
agross-sgV2jX0FEOL9JmXXK+q4OQ, davem-fT/PcQaiUtIeIZ0/mPfg9Q,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, LinoSanfilippo-Mmb7MZpHnFY
On Thu, Aug 25, 2016 at 04:39:03PM -0500, Timur Tabi wrote:
> Add support for the Qualcomm Technologies, Inc. EMAC gigabit Ethernet
> controller.
>
> This driver supports the following features:
> 1) Checksum offload.
> 2) Interrupt coalescing support.
> 3) SGMII phy.
> 4) phylib interface for external phy
>
> Based on original work by
> Niranjana Vishwanathapura <nvishwan-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
> Gilad Avidov <gavidov-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
>
> Signed-off-by: Timur Tabi <timur-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
> ---
>
> v9:
> - Define a separate DT node for the internal phy
> - Kconfig option now selects required PHYLIB
> - Use netdev_alloc_skb_ip_align
> - Use devm functions for enabling clocks
> - Remove redundancy from the Makefile
> - Fix error messages and clean up error paths
> - Miscellaneous reformatting
>
> .../devicetree/bindings/net/qcom-emac.txt | 112 ++
> MAINTAINERS | 6 +
> drivers/net/ethernet/qualcomm/Kconfig | 12 +
> drivers/net/ethernet/qualcomm/Makefile | 2 +
> drivers/net/ethernet/qualcomm/emac/Makefile | 7 +
> drivers/net/ethernet/qualcomm/emac/emac-mac.c | 1530 ++++++++++++++++++++
> drivers/net/ethernet/qualcomm/emac/emac-mac.h | 248 ++++
> drivers/net/ethernet/qualcomm/emac/emac-phy.c | 203 +++
> drivers/net/ethernet/qualcomm/emac/emac-phy.h | 33 +
> drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 722 +++++++++
> drivers/net/ethernet/qualcomm/emac/emac-sgmii.h | 24 +
> drivers/net/ethernet/qualcomm/emac/emac.c | 751 ++++++++++
> drivers/net/ethernet/qualcomm/emac/emac.h | 335 +++++
> 13 files changed, 3985 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/qcom-emac.txt
> create mode 100644 drivers/net/ethernet/qualcomm/emac/Makefile
> create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.c
> create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.h
> create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.c
> create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.h
> create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
> create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
> create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.c
> create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.h
>
> diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt
> new file mode 100644
> index 0000000..4599c78
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/qcom-emac.txt
> @@ -0,0 +1,112 @@
> +Qualcomm Technologies EMAC Gigabit Ethernet Controller
> +
> +This network controller consists of two devices: a MAC and an SGMII
> +internal PHY. Each device is represented by a device tree node. A phandle
> +connects the MAC node to its corresponding internal phy node. Another
> +phandle points to the external PHY node.
> +
> +Required properties:
> +
> +MAC node:
> +- compatible : Should be "qcom,fsm9900-emac".
> +- reg : Offset and length of the register regions for the device
> +- interrupts : Interrupt number used by this controller
> +- mac-address : The 6-byte MAC address. If present, it is the default
> + MAC address.
> +- internal-phy : phandle to the internal PHY node
> +- phy-handle : phandle the the external PHY node
> +
> +Internal PHY node:
> +- compatible : Should be "qcom,fsm9900-emac-sgmii" or "qcom,qdf2432-emac-sgmii".
> +- reg : Offset and length of the register region(s) for the device
> +- interrupts : Interrupt number used by this controller
> +
> +The external phy child node:
> +- reg : The phy address
> +
> +Example:
> +
> +FSM9900:
> +
> +soc {
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + emac0: ethernet@feb20000 {
> + compatible = "qcom,fsm9900-emac";
> + reg = <0xfeb20000 0x10000>,
> + <0xfeb36000 0x1000>;
> + interrupts = <76>;
> +
> + clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>,
> + <&gcc 6>, <&gcc 7>;
> + clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk",
> + "mdio_clk", "tx_clk", "rx_clk", "sys_clk";
> +
> + internal-phy = <&emac_sgmii>;
Can't this use the standard generic phy binding (i.e. 'phys'). It's a
bit confusing as there's the ethernet phy binding (phy-handle) and the
generic one.
> +
> + phy-handle = <&phy0>;
This is bit redundant as the phy is the child node. I guess if you had
multiple devices on the mdio bus you would need it. I'd drop it if you
don't envision needing it and the kernel doesn't require it.
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy@0 {
It's just an example, but don't we require compatible strings for phys
now?
> + reg = <0>;
> + };
> +
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-31 15:00 ` Rob Herring
@ 2016-08-31 15:11 ` Timur Tabi
2016-08-31 20:46 ` Rob Herring
2016-08-31 15:24 ` Andrew Lunn
1 sibling, 1 reply; 17+ messages in thread
From: Timur Tabi @ 2016-08-31 15:11 UTC (permalink / raw)
To: Rob Herring
Cc: netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
sdharia-sgV2jX0FEOL9JmXXK+q4OQ, shankerd-sgV2jX0FEOL9JmXXK+q4OQ,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, cov-sgV2jX0FEOL9JmXXK+q4OQ,
gavidov-sgV2jX0FEOL9JmXXK+q4OQ, andrew-g2DYL2Zd6BY,
bjorn.andersson-QSEj5FYQhm4dnm+yROfE0A,
mlangsdo-H+wXaHxf7aLQT0dZR+AlfA, jcm-H+wXaHxf7aLQT0dZR+AlfA,
agross-sgV2jX0FEOL9JmXXK+q4OQ, davem-fT/PcQaiUtIeIZ0/mPfg9Q,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, LinoSanfilippo-Mmb7MZpHnFY
Rob Herring wrote:
>> + internal-phy = <&emac_sgmii>;
>
> Can't this use the standard generic phy binding (i.e. 'phys'). It's a
> bit confusing as there's the ethernet phy binding (phy-handle) and the
> generic one.
It's not a generic phy. It's a funky "internal phy" that differs among
SOCs. I call it the internal phy, but I could use another name.
Internally, some people call it the "sgmii phy", but I don't think
that's accurate.
I can call it "emac-phy", but I don't know if that's any better.
>> + phy-handle = <&phy0>;
>
> This is bit redundant as the phy is the child node. I guess if you had
> multiple devices on the mdio bus you would need it. I'd drop it if you
> don't envision needing it and the kernel doesn't require it.
That's what I thought to, but without it, of_phy_find_device() won't
work. I need a pointer to the phy node, and I use of_parse_phandle() to
get it:
struct device_node *phy_np;
ret = of_mdiobus_register(mii_bus, np);
if (ret) {
dev_err(&pdev->dev, "could not register mdio bus\n");
return ret;
}
phy_np = of_parse_phandle(np, "phy-handle", 0);
adpt->phydev = of_phy_find_device(phy_np);
>> +
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + phy0: ethernet-phy@0 {
>
> It's just an example, but don't we require compatible strings for phys
> now?
Nope. I had a compatible property, but it broke
of_mdiobus_child_is_phy(). I don't want to specify why kind of phy it
is. I want to let phylib figure it out.
--
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc. Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-31 15:00 ` Rob Herring
2016-08-31 15:11 ` Timur Tabi
@ 2016-08-31 15:24 ` Andrew Lunn
1 sibling, 0 replies; 17+ messages in thread
From: Andrew Lunn @ 2016-08-31 15:24 UTC (permalink / raw)
To: Rob Herring
Cc: Timur Tabi, netdev, devicetree, linux-arm-msm, sdharia, shankerd,
vikrams, cov, gavidov, bjorn.andersson, mlangsdo, jcm, agross,
davem, f.fainelli, LinoSanfilippo
> > +soc {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + emac0: ethernet@feb20000 {
> > + compatible = "qcom,fsm9900-emac";
> > + reg = <0xfeb20000 0x10000>,
> > + <0xfeb36000 0x1000>;
> > + interrupts = <76>;
> > +
> > + clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>,
> > + <&gcc 6>, <&gcc 7>;
> > + clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk",
> > + "mdio_clk", "tx_clk", "rx_clk", "sys_clk";
> > +
> > + internal-phy = <&emac_sgmii>;
>
> Can't this use the standard generic phy binding (i.e. 'phys'). It's a
> bit confusing as there's the ethernet phy binding (phy-handle) and the
> generic one.
Hi Rob
An ethernet PHY is much more complex than a generic PHY. The generic
phy API basically allows you to turn on/off or power up/down. An
Ethernet phy you can find out if there is anybody on the other end,
what speed is being used, set parameters used to negotiate what speed
to use, turn power saving features on off, find out if the other end
has power saving features, change the signal delays between the MAC
and the PHY, configure and handle interrupts when something changes,
configure WoL, etc.
If generic PHYs would of come first, things might be different, but
given that Ethernet PHYs are much much older and well entrenched into
device tree bindings, i don't see them merging.
> > +
> > + phy-handle = <&phy0>;
>
> This is bit redundant as the phy is the child node.
The Internal PHY is a child node. However, there is no reason an
external phy is a child. You sometimes see it connected to another
devices MDIO bus.
> I guess if you had multiple devices on the mdio bus you would need
> it.
And this is where people make errors. They hard code in the driver
that it should use the first phy on the bus. Then some hardware
engineer comes along and adds a second phy to the bus, and it
breaks. It is more robust to explicitly indicate which PHY is
connected to this MAC.
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + phy0: ethernet-phy@0 {
>
> It's just an example, but don't we require compatible strings for phys
> now?
We have never required compatibility strings for Ethernet PHYs. And
due to the stable binding rules, we now never can. The binding
documentation says it may contain compatible strings.
Andrew
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-27 20:42 ` Timur Tabi
@ 2016-08-31 18:57 ` Timur Tabi
2016-08-31 19:15 ` Florian Fainelli
0 siblings, 1 reply; 17+ messages in thread
From: Timur Tabi @ 2016-08-31 18:57 UTC (permalink / raw)
To: Rami Rosen
Cc: Netdev, devicetree, linux-arm-msm, sdharia, shankerd, vikrams,
cov, gavidov, robh+dt, andrew, bjorn.andersson, mlangsdo, jcm,
agross, David Miller, Florian Fainelli, LinoSanfilippo
Timur Tabi wrote:
>
>> Seems that there are several unused members in the emac_stats struct:
>>
>>> +struct emac_stats {
>> ...
>> ...
>> Both rx_bcast_byte_cnt and rx_mcast_byte_cnt are not used anywhere/
>>> + u64 rx_bcast_byte_cnt; /* broadcast packets byte count
>>> (without FCS) */
>>> + u64 rx_mcast_byte_cnt; /* multicast packets byte count
>>> (without FCS) */
>> ...
>> rx_err_addr is not used
>>> + u64 rx_err_addr; /* packets dropped due to address
>>> filtering */
>
> I'll go through the structure and remove the unused fields.
It turns out I cannot actually strip out those "unused" fields. They
are all indirectly used in emac_get_stats64:
u64 *stats_itr = &adpt->stats.rx_ok;
while (addr <= REG_MAC_RX_STATUS_END) {
val = readl_relaxed(adpt->base + addr);
*stats_itr += val;
stats_itr++;
addr += sizeof(u32);
}
--
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc. Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-31 18:57 ` Timur Tabi
@ 2016-08-31 19:15 ` Florian Fainelli
[not found] ` <60d13549-f9ea-694b-1030-0c610e0d9722-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
0 siblings, 1 reply; 17+ messages in thread
From: Florian Fainelli @ 2016-08-31 19:15 UTC (permalink / raw)
To: Timur Tabi, Rami Rosen
Cc: Netdev, devicetree, linux-arm-msm, sdharia, shankerd, vikrams,
cov, gavidov, robh+dt, andrew, bjorn.andersson, mlangsdo, jcm,
agross, David Miller, LinoSanfilippo
On 08/31/2016 11:57 AM, Timur Tabi wrote:
> Timur Tabi wrote:
>>
>>> Seems that there are several unused members in the emac_stats struct:
>>>
>>>> +struct emac_stats {
>>> ...
>>> ...
>>> Both rx_bcast_byte_cnt and rx_mcast_byte_cnt are not used anywhere/
>>>> + u64 rx_bcast_byte_cnt; /* broadcast packets byte count
>>>> (without FCS) */
>>>> + u64 rx_mcast_byte_cnt; /* multicast packets byte count
>>>> (without FCS) */
>>> ...
>>> rx_err_addr is not used
>>>> + u64 rx_err_addr; /* packets dropped due to address
>>>> filtering */
>>
>> I'll go through the structure and remove the unused fields.
>
> It turns out I cannot actually strip out those "unused" fields. They
> are all indirectly used in emac_get_stats64:
>
> u64 *stats_itr = &adpt->stats.rx_ok;
>
> while (addr <= REG_MAC_RX_STATUS_END) {
> val = readl_relaxed(adpt->base + addr);
> *stats_itr += val;
> stats_itr++;
> addr += sizeof(u32);
> }
if these are truly 64-bits stats, how come you are using a single
readl_* to access them? Or is the u64 rx_err_addr just used as temporary
storage and aligned to the largest size you need to deal with?
--
Florian
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
[not found] ` <60d13549-f9ea-694b-1030-0c610e0d9722-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
@ 2016-08-31 19:19 ` Timur Tabi
0 siblings, 0 replies; 17+ messages in thread
From: Timur Tabi @ 2016-08-31 19:19 UTC (permalink / raw)
To: Florian Fainelli, Rami Rosen
Cc: Netdev, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
sdharia-sgV2jX0FEOL9JmXXK+q4OQ, shankerd-sgV2jX0FEOL9JmXXK+q4OQ,
vikrams-sgV2jX0FEOL9JmXXK+q4OQ, cov-sgV2jX0FEOL9JmXXK+q4OQ,
gavidov-sgV2jX0FEOL9JmXXK+q4OQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
andrew-g2DYL2Zd6BY, bjorn.andersson-QSEj5FYQhm4dnm+yROfE0A,
mlangsdo-H+wXaHxf7aLQT0dZR+AlfA, jcm-H+wXaHxf7aLQT0dZR+AlfA,
agross-sgV2jX0FEOL9JmXXK+q4OQ, David Miller,
LinoSanfilippo-Mmb7MZpHnFY
Florian Fainelli wrote:
> if these are truly 64-bits stats, how come you are using a single
> readl_* to access them? Or is the u64 rx_err_addr just used as temporary
> storage and aligned to the largest size you need to deal with?
"*stats_itr += val;" takes the 32-bit val, zero-extends it to 64 bits,
and then adds that to the corresponding 64-bit field in emac_stats.
--
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc. Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-31 15:11 ` Timur Tabi
@ 2016-08-31 20:46 ` Rob Herring
[not found] ` <CAL_Jsq+BtwBtB7Vd8HB+vhucfUmn_0bxRRXmyO13GoCM82LgFg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
0 siblings, 1 reply; 17+ messages in thread
From: Rob Herring @ 2016-08-31 20:46 UTC (permalink / raw)
To: Timur Tabi
Cc: netdev, devicetree, linux-arm-msm, Sagar Dharia,
Shanker Donthineni, Vikram Sethi, Christopher Covington,
Gilad Avidov, Andrew Lunn, Bjorn Andersson, Mark Langsdorf, jcm,
Andy Gross, David Miller, Florian Fainelli, Lino Sanfilippo
On Wed, Aug 31, 2016 at 10:11 AM, Timur Tabi <timur@codeaurora.org> wrote:
> Rob Herring wrote:
>
>>> + internal-phy = <&emac_sgmii>;
>>
>>
>> Can't this use the standard generic phy binding (i.e. 'phys'). It's a
>> bit confusing as there's the ethernet phy binding (phy-handle) and the
>> generic one.
>
>
> It's not a generic phy. It's a funky "internal phy" that differs among
> SOCs. I call it the internal phy, but I could use another name. Internally,
> some people call it the "sgmii phy", but I don't think that's accurate.
Funky internal PHYs are precisely the types of PHYs this binding is
for. It is generic in that the type is not defined. It can be USB,
HDMI, DSI, LVDS, etc.
>
> I can call it "emac-phy", but I don't know if that's any better.
>
>>> + phy-handle = <&phy0>;
>>
>>
>> This is bit redundant as the phy is the child node. I guess if you had
>> multiple devices on the mdio bus you would need it. I'd drop it if you
>> don't envision needing it and the kernel doesn't require it.
>
>
> That's what I thought to, but without it, of_phy_find_device() won't work.
> I need a pointer to the phy node, and I use of_parse_phandle() to get it:
>
> struct device_node *phy_np;
>
> ret = of_mdiobus_register(mii_bus, np);
> if (ret) {
> dev_err(&pdev->dev, "could not register mdio bus\n");
> return ret;
> }
>
> phy_np = of_parse_phandle(np, "phy-handle", 0);
You can just as easily find the child node called ethernet-phy.
> adpt->phydev = of_phy_find_device(phy_np);
>
>>> +
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + phy0: ethernet-phy@0 {
>>
>>
>> It's just an example, but don't we require compatible strings for phys
>> now?
>
>
> Nope. I had a compatible property, but it broke of_mdiobus_child_is_phy().
> I don't want to specify why kind of phy it is. I want to let phylib figure
> it out.
Okay, I'll defer to the mdio folks.
Rob
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
[not found] ` <CAL_Jsq+BtwBtB7Vd8HB+vhucfUmn_0bxRRXmyO13GoCM82LgFg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
@ 2016-08-31 21:00 ` Timur Tabi
[not found] ` <57C74562.3050203-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-09-01 22:49 ` Rob Herring
0 siblings, 2 replies; 17+ messages in thread
From: Timur Tabi @ 2016-08-31 21:00 UTC (permalink / raw)
To: Rob Herring
Cc: netdev, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-msm,
Sagar Dharia, Shanker Donthineni, Vikram Sethi,
Christopher Covington, Gilad Avidov, Andrew Lunn,
Bjorn Andersson, Mark Langsdorf, jcm-H+wXaHxf7aLQT0dZR+AlfA,
Andy Gross, David Miller, Florian Fainelli, Lino Sanfilippo
Rob Herring wrote:
>> It's not a generic phy. It's a funky "internal phy" that differs among
>> >SOCs. I call it the internal phy, but I could use another name. Internally,
>> >some people call it the "sgmii phy", but I don't think that's accurate.
> Funky internal PHYs are precisely the types of PHYs this binding is
> for. It is generic in that the type is not defined. It can be USB,
> HDMI, DSI, LVDS, etc.
I don't understand what you're getting at. There are two IP blocks that
have a private interconnect. One is the MAC, and the other is an
internal PHY, but the driver programs them as one device.
If you want me to make some kind of change, you're going to have to be
more specific.
>> >That's what I thought to, but without it, of_phy_find_device() won't work.
>> >I need a pointer to the phy node, and I use of_parse_phandle() to get it:
>> >
>> > struct device_node *phy_np;
>> >
>> > ret = of_mdiobus_register(mii_bus, np);
>> > if (ret) {
>> > dev_err(&pdev->dev, "could not register mdio bus\n");
>> > return ret;
>> > }
>> >
>> > phy_np = of_parse_phandle(np, "phy-handle", 0);
> You can just as easily find the child node called ethernet-phy.
As Andrew pointed out, using phy-handle allows me to place the phy node
anywhere.
I've already made changes to this design, and every change has raised
objections. I don't see anything wrong with phy-handle. A lot of
drivers use it.
--
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc. Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
[not found] ` <57C74562.3050203-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2016-08-31 21:16 ` Andrew Lunn
0 siblings, 0 replies; 17+ messages in thread
From: Andrew Lunn @ 2016-08-31 21:16 UTC (permalink / raw)
To: Timur Tabi
Cc: Rob Herring, netdev, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm, Sagar Dharia, Shanker Donthineni, Vikram Sethi,
Christopher Covington, Gilad Avidov, Bjorn Andersson,
Mark Langsdorf, jcm-H+wXaHxf7aLQT0dZR+AlfA, Andy Gross,
David Miller, Florian Fainelli, Lino Sanfilippo
> >You can just as easily find the child node called ethernet-phy.
>
> As Andrew pointed out, using phy-handle allows me to place the phy
> node anywhere.
>
> I've already made changes to this design, and every change has
> raised objections. I don't see anything wrong with phy-handle. A
> lot of drivers use it.
Agreed. You should do the same as what all other driver do.
Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] [v9] net: emac: emac gigabit ethernet controller driver
2016-08-31 21:00 ` Timur Tabi
[not found] ` <57C74562.3050203-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2016-09-01 22:49 ` Rob Herring
1 sibling, 0 replies; 17+ messages in thread
From: Rob Herring @ 2016-09-01 22:49 UTC (permalink / raw)
To: Timur Tabi
Cc: netdev, devicetree, linux-arm-msm, Sagar Dharia,
Shanker Donthineni, Vikram Sethi, Christopher Covington,
Gilad Avidov, Andrew Lunn, Bjorn Andersson, Mark Langsdorf, jcm,
Andy Gross, David Miller, Florian Fainelli, Lino Sanfilippo
On Wed, Aug 31, 2016 at 4:00 PM, Timur Tabi <timur@codeaurora.org> wrote:
> Rob Herring wrote:
>>>
>>> It's not a generic phy. It's a funky "internal phy" that differs among
>>> >SOCs. I call it the internal phy, but I could use another name.
>>> > Internally,
>>> >some people call it the "sgmii phy", but I don't think that's accurate.
>
>
>> Funky internal PHYs are precisely the types of PHYs this binding is
>> for. It is generic in that the type is not defined. It can be USB,
>> HDMI, DSI, LVDS, etc.
>
>
> I don't understand what you're getting at. There are two IP blocks that
> have a private interconnect. One is the MAC, and the other is an internal
> PHY, but the driver programs them as one device.
>
> If you want me to make some kind of change, you're going to have to be more
> specific.
The change would simply be use "phys" for the property here and add
#phy-cells to the phy node. See bindings/phy/phy-binding.txt.
And just because you just the phy binding, that doesn't mean you have
to use the generic phy framework in the kernel. I'm not suggesting you
need to. That could change in time as this becomes more common (i.e.
with 10G).
>>> >That's what I thought to, but without it, of_phy_find_device() won't
>>> > work.
>>> >I need a pointer to the phy node, and I use of_parse_phandle() to get
>>> > it:
>>> >
>>> > struct device_node *phy_np;
>>> >
>>> > ret = of_mdiobus_register(mii_bus, np);
>>> > if (ret) {
>>> > dev_err(&pdev->dev, "could not register mdio bus\n");
>>> > return ret;
>>> > }
>>> >
>>> > phy_np = of_parse_phandle(np, "phy-handle", 0);
>
>
>> You can just as easily find the child node called ethernet-phy.
>
>
> As Andrew pointed out, using phy-handle allows me to place the phy node
> anywhere.
But you can't because the binding says (or should say) it is a child node.
> I've already made changes to this design, and every change has raised
> objections. I don't see anything wrong with phy-handle. A lot of drivers
> use it.
You said it wouldn't work. I'm only pointing out that that is not
true. As I said to begin with, if everything else is using it, then
it's fine.
Rob
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2016-09-01 22:49 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-08-25 21:39 [PATCH] [v9] net: emac: emac gigabit ethernet controller driver Timur Tabi
2016-08-27 4:29 ` David Miller
2016-08-27 12:26 ` Timur Tabi
2016-08-27 17:58 ` Florian Fainelli
2016-08-28 4:50 ` David Miller
2016-08-27 20:26 ` Rami Rosen
[not found] ` <CAKoUAr=Z56VxzW=zHu7r9ossdXHQ6xpeYdR5jwhv38zkV_eKFQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-08-27 20:42 ` Timur Tabi
2016-08-31 18:57 ` Timur Tabi
2016-08-31 19:15 ` Florian Fainelli
[not found] ` <60d13549-f9ea-694b-1030-0c610e0d9722-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2016-08-31 19:19 ` Timur Tabi
[not found] ` <1472161143-26417-1-git-send-email-timur-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-08-31 15:00 ` Rob Herring
2016-08-31 15:11 ` Timur Tabi
2016-08-31 20:46 ` Rob Herring
[not found] ` <CAL_Jsq+BtwBtB7Vd8HB+vhucfUmn_0bxRRXmyO13GoCM82LgFg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-08-31 21:00 ` Timur Tabi
[not found] ` <57C74562.3050203-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-08-31 21:16 ` Andrew Lunn
2016-09-01 22:49 ` Rob Herring
2016-08-31 15:24 ` Andrew Lunn
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.