* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-22 17:06 ` Emmanuel Vadot
0 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-11-22 17:06 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, maxime.ripard, wens
Cc: devicetree, linux-arm-kernel, linux-kernel, Emmanuel Vadot
The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
others three only have 1.
Add the num-cs property to each node.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
---
arch/arm/boot/dts/sun7i-a20.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 94cf5a1..ed21982 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -871,6 +871,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 4;
};
spi1: spi@01c06000 {
@@ -885,6 +886,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 1;
};
emac: ethernet@01c0b000 {
@@ -1037,6 +1039,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 1;
};
ahci: sata@01c18000 {
@@ -1079,6 +1082,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 1;
};
pio: pinctrl@01c20800 {
--
2.9.2
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-22 17:06 ` Emmanuel Vadot
0 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-11-22 17:06 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, maxime.ripard, wens
Cc: devicetree, Emmanuel Vadot, linux-kernel, linux-arm-kernel
The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
others three only have 1.
Add the num-cs property to each node.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
---
arch/arm/boot/dts/sun7i-a20.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 94cf5a1..ed21982 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -871,6 +871,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 4;
};
spi1: spi@01c06000 {
@@ -885,6 +886,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 1;
};
emac: ethernet@01c0b000 {
@@ -1037,6 +1039,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 1;
};
ahci: sata@01c18000 {
@@ -1079,6 +1082,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 1;
};
pio: pinctrl@01c20800 {
--
2.9.2
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-22 17:06 ` Emmanuel Vadot
0 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-11-22 17:06 UTC (permalink / raw)
To: linux-arm-kernel
The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
others three only have 1.
Add the num-cs property to each node.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
---
arch/arm/boot/dts/sun7i-a20.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 94cf5a1..ed21982 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -871,6 +871,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 4;
};
spi1: spi at 01c06000 {
@@ -885,6 +886,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 1;
};
emac: ethernet at 01c0b000 {
@@ -1037,6 +1039,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 1;
};
ahci: sata at 01c18000 {
@@ -1079,6 +1082,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+ num-cs = 1;
};
pio: pinctrl at 01c20800 {
--
2.9.2
^ permalink raw reply related [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
2016-11-22 17:06 ` Emmanuel Vadot
(?)
@ 2016-11-24 19:55 ` Maxime Ripard
-1 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-11-24 19:55 UTC (permalink / raw)
To: Emmanuel Vadot
Cc: robh+dt, mark.rutland, linux, wens, devicetree, linux-arm-kernel,
linux-kernel
[-- Attachment #1: Type: text/plain, Size: 497 bytes --]
On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> others three only have 1.
> Add the num-cs property to each node.
>
> Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
I don't think we have any code that uses it at the moment. What is the
rationale behind this patch?
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-24 19:55 ` Maxime Ripard
0 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-11-24 19:55 UTC (permalink / raw)
To: Emmanuel Vadot
Cc: mark.rutland, devicetree, linux, linux-kernel, wens, robh+dt,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 497 bytes --]
On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> others three only have 1.
> Add the num-cs property to each node.
>
> Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
I don't think we have any code that uses it at the moment. What is the
rationale behind this patch?
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-24 19:55 ` Maxime Ripard
0 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-11-24 19:55 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> others three only have 1.
> Add the num-cs property to each node.
>
> Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
I don't think we have any code that uses it at the moment. What is the
rationale behind this patch?
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161124/e1729b42/attachment.sig>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
2016-11-24 19:55 ` Maxime Ripard
@ 2016-11-24 20:05 ` Emmanuel Vadot
-1 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-11-24 20:05 UTC (permalink / raw)
To: Maxime Ripard
Cc: mark.rutland, devicetree, linux, linux-kernel, wens, robh+dt,
linux-arm-kernel
On Thu, 24 Nov 2016 20:55:17 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > others three only have 1.
> > Add the num-cs property to each node.
> >
> > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
>
> I don't think we have any code that uses it at the moment. What is the
> rationale behind this patch?
>
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
Hi Maxime,
If num-cs isn't present nothing prevent to start a transfer with a
non-valid CS pin, resulting in an error.
num-cs are default property especially made for this and a SPI driver
should try to get the property at probe/attach time.
Cheers,
--
Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-24 20:05 ` Emmanuel Vadot
0 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-11-24 20:05 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, 24 Nov 2016 20:55:17 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > others three only have 1.
> > Add the num-cs property to each node.
> >
> > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
>
> I don't think we have any code that uses it at the moment. What is the
> rationale behind this patch?
>
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
Hi Maxime,
If num-cs isn't present nothing prevent to start a transfer with a
non-valid CS pin, resulting in an error.
num-cs are default property especially made for this and a SPI driver
should try to get the property at probe/attach time.
Cheers,
--
Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
2016-11-24 20:05 ` Emmanuel Vadot
(?)
@ 2016-11-25 15:20 ` Maxime Ripard
-1 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-11-25 15:20 UTC (permalink / raw)
To: Emmanuel Vadot
Cc: mark.rutland, devicetree, linux, linux-kernel, wens, robh+dt,
linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 1266 bytes --]
On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> On Thu, 24 Nov 2016 20:55:17 +0100
> Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
>
> > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > others three only have 1.
> > > Add the num-cs property to each node.
> > >
> > > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
> >
> > I don't think we have any code that uses it at the moment. What is the
> > rationale behind this patch?
> >
> > Thanks!
> > Maxime
> >
> > --
> > Maxime Ripard, Free Electrons
> > Embedded Linux and Kernel engineering
> > http://free-electrons.com
>
> Hi Maxime,
>
> If num-cs isn't present nothing prevent to start a transfer with a
> non-valid CS pin, resulting in an error.
> num-cs are default property especially made for this and a SPI driver
> should try to get the property at probe/attach time.
Yes, but as far as I know, our driver doesn't. I'm all in for having
support for that in our driver, but without it, that patch is kind of
useless.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-25 15:20 ` Maxime Ripard
0 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-11-25 15:20 UTC (permalink / raw)
To: Emmanuel Vadot
Cc: mark.rutland, devicetree, linux, linux-kernel, wens, robh+dt,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 1266 bytes --]
On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> On Thu, 24 Nov 2016 20:55:17 +0100
> Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
>
> > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > others three only have 1.
> > > Add the num-cs property to each node.
> > >
> > > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
> >
> > I don't think we have any code that uses it at the moment. What is the
> > rationale behind this patch?
> >
> > Thanks!
> > Maxime
> >
> > --
> > Maxime Ripard, Free Electrons
> > Embedded Linux and Kernel engineering
> > http://free-electrons.com
>
> Hi Maxime,
>
> If num-cs isn't present nothing prevent to start a transfer with a
> non-valid CS pin, resulting in an error.
> num-cs are default property especially made for this and a SPI driver
> should try to get the property at probe/attach time.
Yes, but as far as I know, our driver doesn't. I'm all in for having
support for that in our driver, but without it, that patch is kind of
useless.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-25 15:20 ` Maxime Ripard
0 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-11-25 15:20 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> On Thu, 24 Nov 2016 20:55:17 +0100
> Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
>
> > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > others three only have 1.
> > > Add the num-cs property to each node.
> > >
> > > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
> >
> > I don't think we have any code that uses it at the moment. What is the
> > rationale behind this patch?
> >
> > Thanks!
> > Maxime
> >
> > --
> > Maxime Ripard, Free Electrons
> > Embedded Linux and Kernel engineering
> > http://free-electrons.com
>
> Hi Maxime,
>
> If num-cs isn't present nothing prevent to start a transfer with a
> non-valid CS pin, resulting in an error.
> num-cs are default property especially made for this and a SPI driver
> should try to get the property at probe/attach time.
Yes, but as far as I know, our driver doesn't. I'm all in for having
support for that in our driver, but without it, that patch is kind of
useless.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161125/c080bfc9/attachment.sig>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
2016-11-25 15:20 ` Maxime Ripard
(?)
@ 2016-11-25 21:07 ` Emmanuel Vadot
-1 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-11-25 21:07 UTC (permalink / raw)
To: Maxime Ripard
Cc: mark.rutland, devicetree, linux, linux-kernel, wens, robh+dt,
linux-arm-kernel
On Fri, 25 Nov 2016 16:20:47 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> > On Thu, 24 Nov 2016 20:55:17 +0100
> > Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> >
> > > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > > others three only have 1.
> > > > Add the num-cs property to each node.
> > > >
> > > > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
> > >
> > > I don't think we have any code that uses it at the moment. What is the
> > > rationale behind this patch?
> > >
> > > Thanks!
> > > Maxime
> > >
> > > --
> > > Maxime Ripard, Free Electrons
> > > Embedded Linux and Kernel engineering
> > > http://free-electrons.com
> >
> > Hi Maxime,
> >
> > If num-cs isn't present nothing prevent to start a transfer with a
> > non-valid CS pin, resulting in an error.
> > num-cs are default property especially made for this and a SPI driver
> > should try to get the property at probe/attach time.
>
> Yes, but as far as I know, our driver doesn't. I'm all in for having
> support for that in our driver, but without it, that patch is kind of
> useless.
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
uses it. So it is not useless for downstream user of DTS.
Cheers,
--
Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-25 21:07 ` Emmanuel Vadot
0 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-11-25 21:07 UTC (permalink / raw)
To: Maxime Ripard
Cc: mark.rutland-5wv7dgnIgG8, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-I+IVW8TIWO2tmTQ+vhA3Yw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, wens-jdAy2FN1RRM,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Fri, 25 Nov 2016 16:20:47 +0100
Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> > On Thu, 24 Nov 2016 20:55:17 +0100
> > Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> >
> > > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > > others three only have 1.
> > > > Add the num-cs property to each node.
> > > >
> > > > Signed-off-by: Emmanuel Vadot <manu-xXdDKFdH5B3kFDPD4ZthVA@public.gmane.org>
> > >
> > > I don't think we have any code that uses it at the moment. What is the
> > > rationale behind this patch?
> > >
> > > Thanks!
> > > Maxime
> > >
> > > --
> > > Maxime Ripard, Free Electrons
> > > Embedded Linux and Kernel engineering
> > > http://free-electrons.com
> >
> > Hi Maxime,
> >
> > If num-cs isn't present nothing prevent to start a transfer with a
> > non-valid CS pin, resulting in an error.
> > num-cs are default property especially made for this and a SPI driver
> > should try to get the property at probe/attach time.
>
> Yes, but as far as I know, our driver doesn't. I'm all in for having
> support for that in our driver, but without it, that patch is kind of
> useless.
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
uses it. So it is not useless for downstream user of DTS.
Cheers,
--
Emmanuel Vadot <manu-xXdDKFdH5B3kFDPD4ZthVA@public.gmane.org> <manu-h+KGxgPPiopAfugRpC6u6w@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-11-25 21:07 ` Emmanuel Vadot
0 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-11-25 21:07 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, 25 Nov 2016 16:20:47 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> > On Thu, 24 Nov 2016 20:55:17 +0100
> > Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> >
> > > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > > others three only have 1.
> > > > Add the num-cs property to each node.
> > > >
> > > > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
> > >
> > > I don't think we have any code that uses it at the moment. What is the
> > > rationale behind this patch?
> > >
> > > Thanks!
> > > Maxime
> > >
> > > --
> > > Maxime Ripard, Free Electrons
> > > Embedded Linux and Kernel engineering
> > > http://free-electrons.com
> >
> > Hi Maxime,
> >
> > If num-cs isn't present nothing prevent to start a transfer with a
> > non-valid CS pin, resulting in an error.
> > num-cs are default property especially made for this and a SPI driver
> > should try to get the property at probe/attach time.
>
> Yes, but as far as I know, our driver doesn't. I'm all in for having
> support for that in our driver, but without it, that patch is kind of
> useless.
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
uses it. So it is not useless for downstream user of DTS.
Cheers,
--
Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
2016-11-25 21:07 ` Emmanuel Vadot
@ 2016-12-01 9:21 ` Maxime Ripard
-1 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-12-01 9:21 UTC (permalink / raw)
To: Emmanuel Vadot
Cc: mark.rutland, devicetree, linux, linux-kernel, wens, robh+dt,
linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 2001 bytes --]
Hi Emmanuel,
On Fri, Nov 25, 2016 at 10:07:52PM +0100, Emmanuel Vadot wrote:
> On Fri, 25 Nov 2016 16:20:47 +0100
> Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
>
> > On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> > > On Thu, 24 Nov 2016 20:55:17 +0100
> > > Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> > >
> > > > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > > > others three only have 1.
> > > > > Add the num-cs property to each node.
> > > > >
> > > > > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
> > > >
> > > > I don't think we have any code that uses it at the moment. What is the
> > > > rationale behind this patch?
> > > >
> > > > Thanks!
> > > > Maxime
> > > >
> > > > --
> > > > Maxime Ripard, Free Electrons
> > > > Embedded Linux and Kernel engineering
> > > > http://free-electrons.com
> > >
> > > Hi Maxime,
> > >
> > > If num-cs isn't present nothing prevent to start a transfer with a
> > > non-valid CS pin, resulting in an error.
> > > num-cs are default property especially made for this and a SPI driver
> > > should try to get the property at probe/attach time.
> >
> > Yes, but as far as I know, our driver doesn't. I'm all in for having
> > support for that in our driver, but without it, that patch is kind of
> > useless.
>
> Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
> uses it. So it is not useless for downstream user of DTS.
Ah, I didn't know this was for FreeBSD. So you started to use our DTs,
or do you have some modifications to it? How does that work?
Anyway, the fact that it isn't used by our driver at the moment and
that it's meant for other OSes should be mentionned in the commit log.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-12-01 9:21 ` Maxime Ripard
0 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-12-01 9:21 UTC (permalink / raw)
To: linux-arm-kernel
Hi Emmanuel,
On Fri, Nov 25, 2016 at 10:07:52PM +0100, Emmanuel Vadot wrote:
> On Fri, 25 Nov 2016 16:20:47 +0100
> Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
>
> > On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> > > On Thu, 24 Nov 2016 20:55:17 +0100
> > > Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> > >
> > > > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > > > others three only have 1.
> > > > > Add the num-cs property to each node.
> > > > >
> > > > > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
> > > >
> > > > I don't think we have any code that uses it at the moment. What is the
> > > > rationale behind this patch?
> > > >
> > > > Thanks!
> > > > Maxime
> > > >
> > > > --
> > > > Maxime Ripard, Free Electrons
> > > > Embedded Linux and Kernel engineering
> > > > http://free-electrons.com
> > >
> > > Hi Maxime,
> > >
> > > If num-cs isn't present nothing prevent to start a transfer with a
> > > non-valid CS pin, resulting in an error.
> > > num-cs are default property especially made for this and a SPI driver
> > > should try to get the property at probe/attach time.
> >
> > Yes, but as far as I know, our driver doesn't. I'm all in for having
> > support for that in our driver, but without it, that patch is kind of
> > useless.
>
> Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
> uses it. So it is not useless for downstream user of DTS.
Ah, I didn't know this was for FreeBSD. So you started to use our DTs,
or do you have some modifications to it? How does that work?
Anyway, the fact that it isn't used by our driver at the moment and
that it's meant for other OSes should be mentionned in the commit log.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161201/b66af5d5/attachment-0001.sig>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
2016-12-01 9:21 ` Maxime Ripard
(?)
@ 2016-12-01 10:24 ` Emmanuel Vadot
-1 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-12-01 10:24 UTC (permalink / raw)
To: Maxime Ripard
Cc: mark.rutland, devicetree, linux, linux-kernel, wens, robh+dt,
linux-arm-kernel
Hi Maxime,
On Thu, 1 Dec 2016 10:21:50 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> Hi Emmanuel,
>
> On Fri, Nov 25, 2016 at 10:07:52PM +0100, Emmanuel Vadot wrote:
> > On Fri, 25 Nov 2016 16:20:47 +0100
> > Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> >
> > > On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> > > > On Thu, 24 Nov 2016 20:55:17 +0100
> > > > Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> > > >
> > > > > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > > > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > > > > others three only have 1.
> > > > > > Add the num-cs property to each node.
> > > > > >
> > > > > > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
> > > > >
> > > > > I don't think we have any code that uses it at the moment. What is the
> > > > > rationale behind this patch?
> > > > >
> > > > > Thanks!
> > > > > Maxime
> > > > >
> > > > > --
> > > > > Maxime Ripard, Free Electrons
> > > > > Embedded Linux and Kernel engineering
> > > > > http://free-electrons.com
> > > >
> > > > Hi Maxime,
> > > >
> > > > If num-cs isn't present nothing prevent to start a transfer with a
> > > > non-valid CS pin, resulting in an error.
> > > > num-cs are default property especially made for this and a SPI driver
> > > > should try to get the property at probe/attach time.
> > >
> > > Yes, but as far as I know, our driver doesn't. I'm all in for having
> > > support for that in our driver, but without it, that patch is kind of
> > > useless.
> >
> > Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
> > uses it. So it is not useless for downstream user of DTS.
>
> Ah, I didn't know this was for FreeBSD. So you started to use our DTs,
> or do you have some modifications to it? How does that work?
Yes we use the DTS from linux from quite some times now. We're
currently synced with 4.7-ish.
We either use them directly or modify them according to our needs and
driver support.
> Anyway, the fact that it isn't used by our driver at the moment and
> that it's meant for other OSes should be mentionned in the commit log.
Yeah I understand, I'll send a v2 with this in the commit log.
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
--
Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-12-01 10:24 ` Emmanuel Vadot
0 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-12-01 10:24 UTC (permalink / raw)
To: Maxime Ripard
Cc: mark.rutland-5wv7dgnIgG8, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-I+IVW8TIWO2tmTQ+vhA3Yw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, wens-jdAy2FN1RRM,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Maxime,
On Thu, 1 Dec 2016 10:21:50 +0100
Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> Hi Emmanuel,
>
> On Fri, Nov 25, 2016 at 10:07:52PM +0100, Emmanuel Vadot wrote:
> > On Fri, 25 Nov 2016 16:20:47 +0100
> > Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> >
> > > On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> > > > On Thu, 24 Nov 2016 20:55:17 +0100
> > > > Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> > > >
> > > > > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > > > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > > > > others three only have 1.
> > > > > > Add the num-cs property to each node.
> > > > > >
> > > > > > Signed-off-by: Emmanuel Vadot <manu-xXdDKFdH5B3kFDPD4ZthVA@public.gmane.org>
> > > > >
> > > > > I don't think we have any code that uses it at the moment. What is the
> > > > > rationale behind this patch?
> > > > >
> > > > > Thanks!
> > > > > Maxime
> > > > >
> > > > > --
> > > > > Maxime Ripard, Free Electrons
> > > > > Embedded Linux and Kernel engineering
> > > > > http://free-electrons.com
> > > >
> > > > Hi Maxime,
> > > >
> > > > If num-cs isn't present nothing prevent to start a transfer with a
> > > > non-valid CS pin, resulting in an error.
> > > > num-cs are default property especially made for this and a SPI driver
> > > > should try to get the property at probe/attach time.
> > >
> > > Yes, but as far as I know, our driver doesn't. I'm all in for having
> > > support for that in our driver, but without it, that patch is kind of
> > > useless.
> >
> > Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
> > uses it. So it is not useless for downstream user of DTS.
>
> Ah, I didn't know this was for FreeBSD. So you started to use our DTs,
> or do you have some modifications to it? How does that work?
Yes we use the DTS from linux from quite some times now. We're
currently synced with 4.7-ish.
We either use them directly or modify them according to our needs and
driver support.
> Anyway, the fact that it isn't used by our driver at the moment and
> that it's meant for other OSes should be mentionned in the commit log.
Yeah I understand, I'll send a v2 with this in the commit log.
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
--
Emmanuel Vadot <manu-xXdDKFdH5B3kFDPD4ZthVA@public.gmane.org> <manu-h+KGxgPPiopAfugRpC6u6w@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-12-01 10:24 ` Emmanuel Vadot
0 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-12-01 10:24 UTC (permalink / raw)
To: linux-arm-kernel
Hi Maxime,
On Thu, 1 Dec 2016 10:21:50 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> Hi Emmanuel,
>
> On Fri, Nov 25, 2016 at 10:07:52PM +0100, Emmanuel Vadot wrote:
> > On Fri, 25 Nov 2016 16:20:47 +0100
> > Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> >
> > > On Thu, Nov 24, 2016 at 09:05:09PM +0100, Emmanuel Vadot wrote:
> > > > On Thu, 24 Nov 2016 20:55:17 +0100
> > > > Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> > > >
> > > > > On Tue, Nov 22, 2016 at 06:06:16PM +0100, Emmanuel Vadot wrote:
> > > > > > The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
> > > > > > others three only have 1.
> > > > > > Add the num-cs property to each node.
> > > > > >
> > > > > > Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
> > > > >
> > > > > I don't think we have any code that uses it at the moment. What is the
> > > > > rationale behind this patch?
> > > > >
> > > > > Thanks!
> > > > > Maxime
> > > > >
> > > > > --
> > > > > Maxime Ripard, Free Electrons
> > > > > Embedded Linux and Kernel engineering
> > > > > http://free-electrons.com
> > > >
> > > > Hi Maxime,
> > > >
> > > > If num-cs isn't present nothing prevent to start a transfer with a
> > > > non-valid CS pin, resulting in an error.
> > > > num-cs are default property especially made for this and a SPI driver
> > > > should try to get the property at probe/attach time.
> > >
> > > Yes, but as far as I know, our driver doesn't. I'm all in for having
> > > support for that in our driver, but without it, that patch is kind of
> > > useless.
> >
> > Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
> > uses it. So it is not useless for downstream user of DTS.
>
> Ah, I didn't know this was for FreeBSD. So you started to use our DTs,
> or do you have some modifications to it? How does that work?
Yes we use the DTS from linux from quite some times now. We're
currently synced with 4.7-ish.
We either use them directly or modify them according to our needs and
driver support.
> Anyway, the fact that it isn't used by our driver at the moment and
> that it's meant for other OSes should be mentionned in the commit log.
Yeah I understand, I'll send a v2 with this in the commit log.
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
--
Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-12-03 23:10 ` kbuild test robot
0 siblings, 0 replies; 26+ messages in thread
From: kbuild test robot @ 2016-12-03 23:10 UTC (permalink / raw)
To: Emmanuel Vadot
Cc: kbuild-all, robh+dt, mark.rutland, linux, maxime.ripard, wens,
devicetree, linux-arm-kernel, linux-kernel, Emmanuel Vadot
[-- Attachment #1: Type: text/plain, Size: 1083 bytes --]
Hi Emmanuel,
[auto build test ERROR on robh/for-next]
[also build test ERROR on v4.9-rc7 next-20161202]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Emmanuel-Vadot/ARM-dts-sunxi-Add-num-cs-for-A20-spi-nodes/20161123-034323
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm-vexpress_defconfig (attached as .config)
compiler: arm-linux-gnueabi-gcc (Debian 6.1.1-9) 6.1.1 20160705
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=arm
All errors (new ones prefixed by >>):
>> Error: arch/arm/boot/dts/sun7i-a20.dtsi:874.13-14 syntax error
>> FATAL ERROR: Unable to parse input tree
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 18504 bytes --]
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-12-03 23:10 ` kbuild test robot
0 siblings, 0 replies; 26+ messages in thread
From: kbuild test robot @ 2016-12-03 23:10 UTC (permalink / raw)
Cc: kbuild-all-JC7UmRfGjtg, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, linux-I+IVW8TIWO2tmTQ+vhA3Yw,
maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8, wens-jdAy2FN1RRM,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Emmanuel Vadot
[-- Attachment #1: Type: text/plain, Size: 1083 bytes --]
Hi Emmanuel,
[auto build test ERROR on robh/for-next]
[also build test ERROR on v4.9-rc7 next-20161202]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Emmanuel-Vadot/ARM-dts-sunxi-Add-num-cs-for-A20-spi-nodes/20161123-034323
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm-vexpress_defconfig (attached as .config)
compiler: arm-linux-gnueabi-gcc (Debian 6.1.1-9) 6.1.1 20160705
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=arm
All errors (new ones prefixed by >>):
>> Error: arch/arm/boot/dts/sun7i-a20.dtsi:874.13-14 syntax error
>> FATAL ERROR: Unable to parse input tree
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 18504 bytes --]
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-12-03 23:10 ` kbuild test robot
0 siblings, 0 replies; 26+ messages in thread
From: kbuild test robot @ 2016-12-03 23:10 UTC (permalink / raw)
To: linux-arm-kernel
Hi Emmanuel,
[auto build test ERROR on robh/for-next]
[also build test ERROR on v4.9-rc7 next-20161202]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Emmanuel-Vadot/ARM-dts-sunxi-Add-num-cs-for-A20-spi-nodes/20161123-034323
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm-vexpress_defconfig (attached as .config)
compiler: arm-linux-gnueabi-gcc (Debian 6.1.1-9) 6.1.1 20160705
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=arm
All errors (new ones prefixed by >>):
>> Error: arch/arm/boot/dts/sun7i-a20.dtsi:874.13-14 syntax error
>> FATAL ERROR: Unable to parse input tree
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
-------------- next part --------------
A non-text attachment was scrubbed...
Name: .config.gz
Type: application/gzip
Size: 18504 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161204/e19a77b4/attachment-0001.gz>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
2016-12-01 10:24 ` Emmanuel Vadot
@ 2016-12-05 9:28 ` Maxime Ripard
-1 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-12-05 9:28 UTC (permalink / raw)
To: Emmanuel Vadot
Cc: mark.rutland, devicetree, linux, linux-kernel, wens, robh+dt,
linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 1187 bytes --]
On Thu, Dec 01, 2016 at 11:24:14AM +0100, Emmanuel Vadot wrote:
> > > > > If num-cs isn't present nothing prevent to start a transfer
> > > > > with a non-valid CS pin, resulting in an error. num-cs are
> > > > > default property especially made for this and a SPI driver
> > > > > should try to get the property at probe/attach time.
> > > >
> > > > Yes, but as far as I know, our driver doesn't. I'm all in for
> > > > having support for that in our driver, but without it, that
> > > > patch is kind of useless.
> > >
> > > Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
> > > uses it. So it is not useless for downstream user of DTS.
> >
> > Ah, I didn't know this was for FreeBSD. So you started to use our DTs,
> > or do you have some modifications to it? How does that work?
>
> Yes we use the DTS from linux from quite some times now. We're
> currently synced with 4.7-ish. We either use them directly or
> modify them according to our needs and driver support.
Do you have a link to those modifications?
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-12-05 9:28 ` Maxime Ripard
0 siblings, 0 replies; 26+ messages in thread
From: Maxime Ripard @ 2016-12-05 9:28 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Dec 01, 2016 at 11:24:14AM +0100, Emmanuel Vadot wrote:
> > > > > If num-cs isn't present nothing prevent to start a transfer
> > > > > with a non-valid CS pin, resulting in an error. num-cs are
> > > > > default property especially made for this and a SPI driver
> > > > > should try to get the property at probe/attach time.
> > > >
> > > > Yes, but as far as I know, our driver doesn't. I'm all in for
> > > > having support for that in our driver, but without it, that
> > > > patch is kind of useless.
> > >
> > > Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
> > > uses it. So it is not useless for downstream user of DTS.
> >
> > Ah, I didn't know this was for FreeBSD. So you started to use our DTs,
> > or do you have some modifications to it? How does that work?
>
> Yes we use the DTS from linux from quite some times now. We're
> currently synced with 4.7-ish. We either use them directly or
> modify them according to our needs and driver support.
Do you have a link to those modifications?
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161205/7f666e1b/attachment-0001.sig>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
2016-12-05 9:28 ` Maxime Ripard
@ 2016-12-05 9:39 ` Emmanuel Vadot
-1 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-12-05 9:39 UTC (permalink / raw)
To: Maxime Ripard
Cc: mark.rutland, devicetree, linux, linux-kernel, wens, robh+dt,
linux-arm-kernel
On Mon, 5 Dec 2016 10:28:21 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> On Thu, Dec 01, 2016 at 11:24:14AM +0100, Emmanuel Vadot wrote:
> > > > > > If num-cs isn't present nothing prevent to start a transfer
> > > > > > with a non-valid CS pin, resulting in an error. num-cs are
> > > > > > default property especially made for this and a SPI driver
> > > > > > should try to get the property at probe/attach time.
> > > > >
> > > > > Yes, but as far as I know, our driver doesn't. I'm all in for
> > > > > having support for that in our driver, but without it, that
> > > > > patch is kind of useless.
> > > >
> > > > Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
> > > > uses it. So it is not useless for downstream user of DTS.
> > >
> > > Ah, I didn't know this was for FreeBSD. So you started to use our DTs,
> > > or do you have some modifications to it? How does that work?
> >
> > Yes we use the DTS from linux from quite some times now. We're
> > currently synced with 4.7-ish. We either use them directly or
> > modify them according to our needs and driver support.
>
> Do you have a link to those modifications?
>
> Thanks,
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
Sure,
https://svnweb.freebsd.org/base/head/sys/boot/fdt/dts/arm/
--
Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes
@ 2016-12-05 9:39 ` Emmanuel Vadot
0 siblings, 0 replies; 26+ messages in thread
From: Emmanuel Vadot @ 2016-12-05 9:39 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, 5 Dec 2016 10:28:21 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> On Thu, Dec 01, 2016 at 11:24:14AM +0100, Emmanuel Vadot wrote:
> > > > > > If num-cs isn't present nothing prevent to start a transfer
> > > > > > with a non-valid CS pin, resulting in an error. num-cs are
> > > > > > default property especially made for this and a SPI driver
> > > > > > should try to get the property at probe/attach time.
> > > > >
> > > > > Yes, but as far as I know, our driver doesn't. I'm all in for
> > > > > having support for that in our driver, but without it, that
> > > > > patch is kind of useless.
> > > >
> > > > Yes the Linux driver doesn't use it but my upcoming one for FreeBSD
> > > > uses it. So it is not useless for downstream user of DTS.
> > >
> > > Ah, I didn't know this was for FreeBSD. So you started to use our DTs,
> > > or do you have some modifications to it? How does that work?
> >
> > Yes we use the DTS from linux from quite some times now. We're
> > currently synced with 4.7-ish. We either use them directly or
> > modify them according to our needs and driver support.
>
> Do you have a link to those modifications?
>
> Thanks,
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
Sure,
https://svnweb.freebsd.org/base/head/sys/boot/fdt/dts/arm/
--
Emmanuel Vadot <manu@bidouilliste.com> <manu@freebsd.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
end of thread, other threads:[~2016-12-05 9:40 UTC | newest]
Thread overview: 26+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-11-22 17:06 [PATCH] ARM: dts: sunxi: Add num-cs for A20 spi nodes Emmanuel Vadot
2016-11-22 17:06 ` Emmanuel Vadot
2016-11-22 17:06 ` Emmanuel Vadot
2016-11-24 19:55 ` Maxime Ripard
2016-11-24 19:55 ` Maxime Ripard
2016-11-24 19:55 ` Maxime Ripard
2016-11-24 20:05 ` Emmanuel Vadot
2016-11-24 20:05 ` Emmanuel Vadot
2016-11-25 15:20 ` Maxime Ripard
2016-11-25 15:20 ` Maxime Ripard
2016-11-25 15:20 ` Maxime Ripard
2016-11-25 21:07 ` Emmanuel Vadot
2016-11-25 21:07 ` Emmanuel Vadot
2016-11-25 21:07 ` Emmanuel Vadot
2016-12-01 9:21 ` Maxime Ripard
2016-12-01 9:21 ` Maxime Ripard
2016-12-01 10:24 ` Emmanuel Vadot
2016-12-01 10:24 ` Emmanuel Vadot
2016-12-01 10:24 ` Emmanuel Vadot
2016-12-05 9:28 ` Maxime Ripard
2016-12-05 9:28 ` Maxime Ripard
2016-12-05 9:39 ` Emmanuel Vadot
2016-12-05 9:39 ` Emmanuel Vadot
2016-12-03 23:10 ` kbuild test robot
2016-12-03 23:10 ` kbuild test robot
2016-12-03 23:10 ` kbuild test robot
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.