* [PATCH v2 0/9] Allwinner H5 and Orange Pi PC2 support
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3.
This patch adds support for it, along with the first available
board -- Orange Pi PC2.
P.S. Some patches are sent wrongly, please ignore them. Sorry.
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (6):
drivers: pinctrl: add driver for Allwinner H5 SoC
arm64: allwinner: Kconfig: add essential pinctrl driver for H5
clk: sunxi-ng: add support for Allwinner H5 SoC
clk: sunxi-ng: remove transitional headers for dt-bindings
dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
ASoC: sunxi: allow the analog codec driver to be built on ARM64
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
arch/arm/boot/dts/sun8i-h3.dtsi | 501 +-----------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 557 ++++++++++++++++++++
arch/arm64/Kconfig.platforms | 5 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 140 ++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
drivers/clk/sunxi-ng/Kconfig | 6 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++-
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
drivers/dma/Kconfig | 2 +-
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c | 558 +++++++++++++++++++++
.../clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
.../reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
sound/soc/sunxi/Kconfig | 2 +-
20 files changed, 1628 insertions(+), 534 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
rename include/dt-bindings/clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (95%)
rename include/dt-bindings/reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (94%)
--
2.11.0
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 0/9] Allwinner H5 and Orange Pi PC2 support
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3.
This patch adds support for it, along with the first available
board -- Orange Pi PC2.
P.S. Some patches are sent wrongly, please ignore them. Sorry.
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (6):
drivers: pinctrl: add driver for Allwinner H5 SoC
arm64: allwinner: Kconfig: add essential pinctrl driver for H5
clk: sunxi-ng: add support for Allwinner H5 SoC
clk: sunxi-ng: remove transitional headers for dt-bindings
dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
ASoC: sunxi: allow the analog codec driver to be built on ARM64
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
arch/arm/boot/dts/sun8i-h3.dtsi | 501 +-----------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 557 ++++++++++++++++++++
arch/arm64/Kconfig.platforms | 5 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 140 ++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
drivers/clk/sunxi-ng/Kconfig | 6 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++-
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
drivers/dma/Kconfig | 2 +-
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c | 558 +++++++++++++++++++++
.../clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
.../reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
sound/soc/sunxi/Kconfig | 2 +-
20 files changed, 1628 insertions(+), 534 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
rename include/dt-bindings/clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (95%)
rename include/dt-bindings/reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (94%)
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 0/9] Allwinner H5 and Orange Pi PC2 support
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3.
This patch adds support for it, along with the first available
board -- Orange Pi PC2.
P.S. Some patches are sent wrongly, please ignore them. Sorry.
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (6):
drivers: pinctrl: add driver for Allwinner H5 SoC
arm64: allwinner: Kconfig: add essential pinctrl driver for H5
clk: sunxi-ng: add support for Allwinner H5 SoC
clk: sunxi-ng: remove transitional headers for dt-bindings
dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
ASoC: sunxi: allow the analog codec driver to be built on ARM64
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
arch/arm/boot/dts/sun8i-h3.dtsi | 501 +-----------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 557 ++++++++++++++++++++
arch/arm64/Kconfig.platforms | 5 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 140 ++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
drivers/clk/sunxi-ng/Kconfig | 6 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++-
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
drivers/dma/Kconfig | 2 +-
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c | 558 +++++++++++++++++++++
.../clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
.../reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} | 11 +-
sound/soc/sunxi/Kconfig | 2 +-
20 files changed, 1628 insertions(+), 534 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
rename include/dt-bindings/clock/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (95%)
rename include/dt-bindings/reset/{sun8i-h3-ccu.h => sunxi-h3-h5-ccu.h} (94%)
--
2.11.0
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-01-26 15:48 ` Icenowy Zheng
-1 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
Based on the Allwinner H5 datasheet and the pinctrl driver of the
backward-compatible H3 this introduces the pin multiplex assignments for
the H5 SoC.
H5 introduced some more pin functions (e.g. three more groups of TS
pins, and one more groups of SIM pins) than H3.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v2:
- Fixed interrupt banks. (There's one more GPIO banks (PF) that can do
interrupt handling on H5)
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c | 558 +++++++++++++++++++++
4 files changed, 564 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index c931fb1c01a6..2fd688c8dbdb 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -23,6 +23,7 @@ Required properties:
"allwinner,sun8i-h3-pinctrl"
"allwinner,sun8i-h3-r-pinctrl"
"allwinner,sun50i-a64-pinctrl"
+ "allwinner,sun50i-h5-r-pinctrl"
"nextthing,gr8-pinctrl"
- reg: Should contain the register physical address and length for the
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 8ba10d830ce2..92d845827577 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -72,4 +72,8 @@ config PINCTRL_SUN50I_A64
bool
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_H5
+ bool
+ select PINCTRL_SUNXI
+
endif
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index 7bcb4683bce5..f9a3855c42f1 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -16,5 +16,6 @@ obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
obj-$(CONFIG_PINCTRL_SUN8I_H3_R) += pinctrl-sun8i-h3-r.o
obj-$(CONFIG_PINCTRL_SUN8I_V3S) += pinctrl-sun8i-v3s.o
+obj-$(CONFIG_PINCTRL_SUN50I_H5) += pinctrl-sun50i-h5.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
obj-$(CONFIG_PINCTRL_SUN9I_A80_R) += pinctrl-sun9i-a80-r.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
new file mode 100644
index 000000000000..ccf9419e9418
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
@@ -0,0 +1,558 @@
+/*
+ * Allwinner H5 SoC pinctrl driver.
+ *
+ * Copyright (C) 2016 Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
+ *
+ * Based on pinctrl-sun8i-h3.c, which is:
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * Based on pinctrl-sun8i-a23.c, which is:
+ * Copyright (C) 2014 Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun50i_h5_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), /* PA_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), /* PA_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), /* PA_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), /* PA_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), /* PA_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "pwm0"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), /* PA_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* PWREN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), /* PA_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), /* PA_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DATA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), /* PA_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), /* PA_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DET */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), /* PA_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x3, "di"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), /* PA_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x3, "di"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)), /* PA_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x3, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)), /* PA_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)), /* PA_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)), /* PA_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)), /* PA_EINT16 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* OUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)), /* PA_EINT17 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* SYNC */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)), /* PA_EINT18 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)), /* PA_EINT19 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPEN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)), /* PA_EINT20 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DIN */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPPP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)), /* PA_EINT21 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* MOSI */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "spi0"), /* MISO */
+ SUNXI_FUNCTION(0x4, "mmc2")), /* DS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */
+ SUNXI_FUNCTION(0x4, "spi0")), /* MISO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CMD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0")), /* RB1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQS */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* RST */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD3 */
+ SUNXI_FUNCTION(0x3, "di"), /* TX */
+ SUNXI_FUNCTION(0x4, "ts2")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD2 */
+ SUNXI_FUNCTION(0x3, "di"), /* RX */
+ SUNXI_FUNCTION(0x4, "ts2")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD1 */
+ SUNXI_FUNCTION(0x4, "ts2")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD0 */
+ SUNXI_FUNCTION(0x4, "ts2")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXCK */
+ SUNXI_FUNCTION(0x4, "ts2")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXCTL/RXDV */
+ SUNXI_FUNCTION(0x4, "ts2")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXERR */
+ SUNXI_FUNCTION(0x4, "ts2")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD3 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D3 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD2 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D4 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD1 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D5 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD0 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D6 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* CRS */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D7 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXCK */
+ SUNXI_FUNCTION(0x4, "sim")), /* PWREN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXCTL/TXEN */
+ SUNXI_FUNCTION(0x4, "sim")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXERR */
+ SUNXI_FUNCTION(0x4, "sim")), /* DATA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* CLKIN/COL */
+ SUNXI_FUNCTION(0x4, "sim")), /* RST */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* MDC */
+ SUNXI_FUNCTION(0x4, "sim")), /* DET */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* MDIO */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* PCLK */
+ SUNXI_FUNCTION(0x3, "ts0")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "ts0")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "ts0")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "ts0")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D0 */
+ SUNXI_FUNCTION(0x3, "ts0")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D1 */
+ SUNXI_FUNCTION(0x3, "ts0")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D2 */
+ SUNXI_FUNCTION(0x3, "ts0")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D3 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D3 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D4 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D4 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D5 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D5 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D6 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D6 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D7 */
+ SUNXI_FUNCTION(0x3, "ts"), /* D7 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SDA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "sim")), /* VPPEN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "sim")), /* VPPPP */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PF_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PF_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PF_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PF_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PF_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PF_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PF_EINT6 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)), /* PG_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)), /* PG_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)), /* PG_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)), /* PG_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)), /* PG_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)), /* PG_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)), /* PG_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)), /* PG_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)), /* PG_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)), /* PG_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* SYNC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)), /* PG_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)), /* PG_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 12)), /* PG_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 13)), /* PG_EINT13 */
+};
+
+static const struct sunxi_pinctrl_desc sun50i_h5_pinctrl_data = {
+ .pins = sun50i_h5_pins,
+ .npins = ARRAY_SIZE(sun50i_h5_pins),
+ .irq_banks = 2,
+ .irq_read_needs_mux = true
+};
+
+static int sun50i_h5_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev,
+ &sun50i_h5_pinctrl_data);
+}
+
+static const struct of_device_id sun50i_h5_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-h5-pinctrl", },
+ {}
+};
+
+static struct platform_driver sun50i_h5_pinctrl_driver = {
+ .probe = sun50i_h5_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-h5-pinctrl",
+ .of_match_table = sun50i_h5_pinctrl_match,
+ },
+};
+builtin_platform_driver(sun50i_h5_pinctrl_driver);
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
Based on the Allwinner H5 datasheet and the pinctrl driver of the
backward-compatible H3 this introduces the pin multiplex assignments for
the H5 SoC.
H5 introduced some more pin functions (e.g. three more groups of TS
pins, and one more groups of SIM pins) than H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Fixed interrupt banks. (There's one more GPIO banks (PF) that can do
interrupt handling on H5)
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c | 558 +++++++++++++++++++++
4 files changed, 564 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index c931fb1c01a6..2fd688c8dbdb 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -23,6 +23,7 @@ Required properties:
"allwinner,sun8i-h3-pinctrl"
"allwinner,sun8i-h3-r-pinctrl"
"allwinner,sun50i-a64-pinctrl"
+ "allwinner,sun50i-h5-r-pinctrl"
"nextthing,gr8-pinctrl"
- reg: Should contain the register physical address and length for the
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 8ba10d830ce2..92d845827577 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -72,4 +72,8 @@ config PINCTRL_SUN50I_A64
bool
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_H5
+ bool
+ select PINCTRL_SUNXI
+
endif
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index 7bcb4683bce5..f9a3855c42f1 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -16,5 +16,6 @@ obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
obj-$(CONFIG_PINCTRL_SUN8I_H3_R) += pinctrl-sun8i-h3-r.o
obj-$(CONFIG_PINCTRL_SUN8I_V3S) += pinctrl-sun8i-v3s.o
+obj-$(CONFIG_PINCTRL_SUN50I_H5) += pinctrl-sun50i-h5.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
obj-$(CONFIG_PINCTRL_SUN9I_A80_R) += pinctrl-sun9i-a80-r.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
new file mode 100644
index 000000000000..ccf9419e9418
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
@@ -0,0 +1,558 @@
+/*
+ * Allwinner H5 SoC pinctrl driver.
+ *
+ * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on pinctrl-sun8i-h3.c, which is:
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * Based on pinctrl-sun8i-a23.c, which is:
+ * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun50i_h5_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), /* PA_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), /* PA_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), /* PA_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), /* PA_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), /* PA_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "pwm0"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), /* PA_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* PWREN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), /* PA_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), /* PA_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DATA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), /* PA_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), /* PA_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DET */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), /* PA_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x3, "di"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), /* PA_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x3, "di"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)), /* PA_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x3, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)), /* PA_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)), /* PA_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)), /* PA_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)), /* PA_EINT16 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* OUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)), /* PA_EINT17 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* SYNC */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)), /* PA_EINT18 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)), /* PA_EINT19 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPEN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)), /* PA_EINT20 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DIN */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPPP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)), /* PA_EINT21 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* MOSI */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "spi0"), /* MISO */
+ SUNXI_FUNCTION(0x4, "mmc2")), /* DS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */
+ SUNXI_FUNCTION(0x4, "spi0")), /* MISO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CMD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0")), /* RB1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQS */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* RST */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD3 */
+ SUNXI_FUNCTION(0x3, "di"), /* TX */
+ SUNXI_FUNCTION(0x4, "ts2")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD2 */
+ SUNXI_FUNCTION(0x3, "di"), /* RX */
+ SUNXI_FUNCTION(0x4, "ts2")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD1 */
+ SUNXI_FUNCTION(0x4, "ts2")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD0 */
+ SUNXI_FUNCTION(0x4, "ts2")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXCK */
+ SUNXI_FUNCTION(0x4, "ts2")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXCTL/RXDV */
+ SUNXI_FUNCTION(0x4, "ts2")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXERR */
+ SUNXI_FUNCTION(0x4, "ts2")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD3 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D3 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD2 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D4 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD1 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D5 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD0 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D6 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* CRS */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D7 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXCK */
+ SUNXI_FUNCTION(0x4, "sim")), /* PWREN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXCTL/TXEN */
+ SUNXI_FUNCTION(0x4, "sim")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXERR */
+ SUNXI_FUNCTION(0x4, "sim")), /* DATA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* CLKIN/COL */
+ SUNXI_FUNCTION(0x4, "sim")), /* RST */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* MDC */
+ SUNXI_FUNCTION(0x4, "sim")), /* DET */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* MDIO */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* PCLK */
+ SUNXI_FUNCTION(0x3, "ts0")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "ts0")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "ts0")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "ts0")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D0 */
+ SUNXI_FUNCTION(0x3, "ts0")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D1 */
+ SUNXI_FUNCTION(0x3, "ts0")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D2 */
+ SUNXI_FUNCTION(0x3, "ts0")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D3 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D3 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D4 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D4 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D5 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D5 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D6 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D6 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D7 */
+ SUNXI_FUNCTION(0x3, "ts"), /* D7 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SDA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "sim")), /* VPPEN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "sim")), /* VPPPP */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PF_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PF_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PF_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PF_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PF_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PF_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PF_EINT6 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)), /* PG_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)), /* PG_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)), /* PG_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)), /* PG_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)), /* PG_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)), /* PG_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)), /* PG_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)), /* PG_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)), /* PG_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)), /* PG_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* SYNC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)), /* PG_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)), /* PG_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 12)), /* PG_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 13)), /* PG_EINT13 */
+};
+
+static const struct sunxi_pinctrl_desc sun50i_h5_pinctrl_data = {
+ .pins = sun50i_h5_pins,
+ .npins = ARRAY_SIZE(sun50i_h5_pins),
+ .irq_banks = 2,
+ .irq_read_needs_mux = true
+};
+
+static int sun50i_h5_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev,
+ &sun50i_h5_pinctrl_data);
+}
+
+static const struct of_device_id sun50i_h5_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-h5-pinctrl", },
+ {}
+};
+
+static struct platform_driver sun50i_h5_pinctrl_driver = {
+ .probe = sun50i_h5_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-h5-pinctrl",
+ .of_match_table = sun50i_h5_pinctrl_match,
+ },
+};
+builtin_platform_driver(sun50i_h5_pinctrl_driver);
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
Based on the Allwinner H5 datasheet and the pinctrl driver of the
backward-compatible H3 this introduces the pin multiplex assignments for
the H5 SoC.
H5 introduced some more pin functions (e.g. three more groups of TS
pins, and one more groups of SIM pins) than H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Fixed interrupt banks. (There's one more GPIO banks (PF) that can do
interrupt handling on H5)
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c | 558 +++++++++++++++++++++
4 files changed, 564 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index c931fb1c01a6..2fd688c8dbdb 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -23,6 +23,7 @@ Required properties:
"allwinner,sun8i-h3-pinctrl"
"allwinner,sun8i-h3-r-pinctrl"
"allwinner,sun50i-a64-pinctrl"
+ "allwinner,sun50i-h5-r-pinctrl"
"nextthing,gr8-pinctrl"
- reg: Should contain the register physical address and length for the
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 8ba10d830ce2..92d845827577 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -72,4 +72,8 @@ config PINCTRL_SUN50I_A64
bool
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_H5
+ bool
+ select PINCTRL_SUNXI
+
endif
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index 7bcb4683bce5..f9a3855c42f1 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -16,5 +16,6 @@ obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
obj-$(CONFIG_PINCTRL_SUN8I_H3_R) += pinctrl-sun8i-h3-r.o
obj-$(CONFIG_PINCTRL_SUN8I_V3S) += pinctrl-sun8i-v3s.o
+obj-$(CONFIG_PINCTRL_SUN50I_H5) += pinctrl-sun50i-h5.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
obj-$(CONFIG_PINCTRL_SUN9I_A80_R) += pinctrl-sun9i-a80-r.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
new file mode 100644
index 000000000000..ccf9419e9418
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h5.c
@@ -0,0 +1,558 @@
+/*
+ * Allwinner H5 SoC pinctrl driver.
+ *
+ * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on pinctrl-sun8i-h3.c, which is:
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * Based on pinctrl-sun8i-a23.c, which is:
+ * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun50i_h5_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), /* PA_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), /* PA_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), /* PA_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), /* PA_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), /* PA_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "pwm0"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), /* PA_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* PWREN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), /* PA_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), /* PA_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DATA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), /* PA_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), /* PA_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DET */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), /* PA_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x3, "di"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), /* PA_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x3, "di"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)), /* PA_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x3, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)), /* PA_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)), /* PA_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)), /* PA_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)), /* PA_EINT16 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* OUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)), /* PA_EINT17 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* SYNC */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)), /* PA_EINT18 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)), /* PA_EINT19 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPEN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)), /* PA_EINT20 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DIN */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPPP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)), /* PA_EINT21 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* MOSI */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "spi0"), /* MISO */
+ SUNXI_FUNCTION(0x4, "mmc2")), /* DS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */
+ SUNXI_FUNCTION(0x4, "spi0")), /* MISO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CMD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0")), /* RB1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQS */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* RST */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD3 */
+ SUNXI_FUNCTION(0x3, "di"), /* TX */
+ SUNXI_FUNCTION(0x4, "ts2")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD2 */
+ SUNXI_FUNCTION(0x3, "di"), /* RX */
+ SUNXI_FUNCTION(0x4, "ts2")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD1 */
+ SUNXI_FUNCTION(0x4, "ts2")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXD0 */
+ SUNXI_FUNCTION(0x4, "ts2")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXCK */
+ SUNXI_FUNCTION(0x4, "ts2")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXCTL/RXDV */
+ SUNXI_FUNCTION(0x4, "ts2")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* RXERR */
+ SUNXI_FUNCTION(0x4, "ts2")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD3 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D3 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD2 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D4 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD1 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D5 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXD0 */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D6 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* CRS */
+ SUNXI_FUNCTION(0x4, "ts2"), /* D7 */
+ SUNXI_FUNCTION(0x5, "ts3")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXCK */
+ SUNXI_FUNCTION(0x4, "sim")), /* PWREN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXCTL/TXEN */
+ SUNXI_FUNCTION(0x4, "sim")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* TXERR */
+ SUNXI_FUNCTION(0x4, "sim")), /* DATA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* CLKIN/COL */
+ SUNXI_FUNCTION(0x4, "sim")), /* RST */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac"), /* MDC */
+ SUNXI_FUNCTION(0x4, "sim")), /* DET */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* MDIO */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* PCLK */
+ SUNXI_FUNCTION(0x3, "ts0")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "ts0")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "ts0")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "ts0")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D0 */
+ SUNXI_FUNCTION(0x3, "ts0")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D1 */
+ SUNXI_FUNCTION(0x3, "ts0")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D2 */
+ SUNXI_FUNCTION(0x3, "ts0")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D3 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D3 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D4 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D4 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D5 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D5 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D6 */
+ SUNXI_FUNCTION(0x3, "ts0"), /* D6 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D7 */
+ SUNXI_FUNCTION(0x3, "ts"), /* D7 */
+ SUNXI_FUNCTION(0x4, "ts1")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SDA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "sim")), /* VPPEN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "sim")), /* VPPPP */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PF_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PF_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PF_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PF_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PF_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PF_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PF_EINT6 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)), /* PG_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)), /* PG_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)), /* PG_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)), /* PG_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)), /* PG_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)), /* PG_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)), /* PG_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)), /* PG_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)), /* PG_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)), /* PG_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* SYNC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)), /* PG_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)), /* PG_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 12)), /* PG_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 13)), /* PG_EINT13 */
+};
+
+static const struct sunxi_pinctrl_desc sun50i_h5_pinctrl_data = {
+ .pins = sun50i_h5_pins,
+ .npins = ARRAY_SIZE(sun50i_h5_pins),
+ .irq_banks = 2,
+ .irq_read_needs_mux = true
+};
+
+static int sun50i_h5_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev,
+ &sun50i_h5_pinctrl_data);
+}
+
+static const struct of_device_id sun50i_h5_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-h5-pinctrl", },
+ {}
+};
+
+static struct platform_driver sun50i_h5_pinctrl_driver = {
+ .probe = sun50i_h5_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-h5-pinctrl",
+ .of_match_table = sun50i_h5_pinctrl_match,
+ },
+};
+builtin_platform_driver(sun50i_h5_pinctrl_driver);
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 2/9] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-01-26 15:48 ` Icenowy Zheng
-1 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
a slightly advanced driver, and the other (called "CPUs") is just equal
to the on in H3, and the H3 driver can be just reused.
Select the two necessary pinctrl drivers when building kernel for
Allwinner SoCs.
Also add H5 in the option's description.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
arch/arm64/Kconfig.platforms | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 715ef1256838..e11523d204b5 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -5,8 +5,11 @@ config ARCH_SUNXI
select GENERIC_IRQ_CHIP
select PINCTRL
select PINCTRL_SUN50I_A64
+ select PINCTRL_SUN50I_H5
+ select PINCTRL_SUN8I_H3_R
help
- This enables support for Allwinner sunxi based SoCs like the A64.
+ This enables support for Allwinner sunxi based SoCs like the A64
+ and H5.
config ARCH_ALPINE
bool "Annapurna Labs Alpine platform"
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 2/9] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
a slightly advanced driver, and the other (called "CPUs") is just equal
to the on in H3, and the H3 driver can be just reused.
Select the two necessary pinctrl drivers when building kernel for
Allwinner SoCs.
Also add H5 in the option's description.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
arch/arm64/Kconfig.platforms | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 715ef1256838..e11523d204b5 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -5,8 +5,11 @@ config ARCH_SUNXI
select GENERIC_IRQ_CHIP
select PINCTRL
select PINCTRL_SUN50I_A64
+ select PINCTRL_SUN50I_H5
+ select PINCTRL_SUN8I_H3_R
help
- This enables support for Allwinner sunxi based SoCs like the A64.
+ This enables support for Allwinner sunxi based SoCs like the A64
+ and H5.
config ARCH_ALPINE
bool "Annapurna Labs Alpine platform"
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 2/9] arm64: allwinner: Kconfig: add essential pinctrl driver for H5
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
H5 SoC has two pin controllers, one (in user manual called "CPUx") needs
a slightly advanced driver, and the other (called "CPUs") is just equal
to the on in H3, and the H3 driver can be just reused.
Select the two necessary pinctrl drivers when building kernel for
Allwinner SoCs.
Also add H5 in the option's description.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
arch/arm64/Kconfig.platforms | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 715ef1256838..e11523d204b5 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -5,8 +5,11 @@ config ARCH_SUNXI
select GENERIC_IRQ_CHIP
select PINCTRL
select PINCTRL_SUN50I_A64
+ select PINCTRL_SUN50I_H5
+ select PINCTRL_SUN8I_H3_R
help
- This enables support for Allwinner sunxi based SoCs like the A64.
+ This enables support for Allwinner sunxi based SoCs like the A64
+ and H5.
config ARCH_ALPINE
bool "Annapurna Labs Alpine platform"
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 3/9] clk: sunxi-ng: add support for Allwinner H5 SoC
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-01-26 15:48 ` Icenowy Zheng
-1 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
clocks removed (for new MMC controller) and a new bus gate/reset
imported.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
A giant rewrite since v1.
It now do not use a dedicated driver for H5, but altered the CCU driver
of H3 to support H5.
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
drivers/clk/sunxi-ng/Kconfig | 6 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++++++++++++++---
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +----------------
include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 148 +++++++++++++++++
include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +-----------
include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 106 ++++++++++++
9 files changed, 431 insertions(+), 276 deletions(-)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
mode change 100644 => 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
create mode 100644 include/dt-bindings/clock/sunxi-h3-h5-ccu.h
mode change 100644 => 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
create mode 100644 include/dt-bindings/reset/sunxi-h3-h5-ccu.h
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index f6032cf63f12..a33a4a5ecffa 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -9,6 +9,7 @@ Required properties :
- "allwinner,sun8i-h3-ccu"
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun50i-a64-ccu"
+ - "allwinner,sun50i-h5-ccu"
- reg: Must contain the registers base address and length
- clocks: phandle to the oscillators feeding the CCU. Two are needed:
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 71f11cd1647b..bdf18e846731 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -108,8 +108,8 @@ config SUN8I_A33_CCU
select SUNXI_CCU_PHASE
default MACH_SUN8I
-config SUN8I_H3_CCU
- bool "Support for the Allwinner H3 CCU"
+config SUNXI_H3_H5_CCU
+ bool "Support for the Allwinner H3/H5 CCU"
select SUNXI_CCU_DIV
select SUNXI_CCU_NK
select SUNXI_CCU_NKM
@@ -117,7 +117,7 @@ config SUN8I_H3_CCU
select SUNXI_CCU_NM
select SUNXI_CCU_MP
select SUNXI_CCU_PHASE
- default MACH_SUN8I
+ default MACH_SUN8I || (ARM64 && ARCH_SUNXI)
config SUN8I_V3S_CCU
bool "Support for the Allwinner V3s CCU"
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index a8afdf9c7668..cdc3359abbfe 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,5 +23,5 @@ obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
obj-$(CONFIG_SUN6I_A31_CCU) += ccu-sun6i-a31.o
obj-$(CONFIG_SUN8I_A23_CCU) += ccu-sun8i-a23.o
obj-$(CONFIG_SUN8I_A33_CCU) += ccu-sun8i-a33.o
-obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
+obj-$(CONFIG_SUNXI_H3_H5_CCU) += ccu-sunxi-h3-h5.o
obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
similarity index 80%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.c
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
index a26c8a19fe93..b7b9f85f5c9f 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
@@ -27,7 +27,7 @@
#include "ccu_nm.h"
#include "ccu_phase.h"
-#include "ccu-sun8i-h3.h"
+#include "ccu-sunxi-h3-h5.h"
static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
"osc24M", 0x000,
@@ -47,7 +47,7 @@ static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
* We don't have any need for the variable divider for now, so we just
* hardcode it to match with the clock names
*/
-#define SUN8I_H3_PLL_AUDIO_REG 0x008
+#define SUNXI_H3_H5_PLL_AUDIO_REG 0x008
static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
"osc24M", 0x008,
@@ -300,8 +300,10 @@ static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
-static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_scr1_clk, "bus-scr1", "apb2",
+ 0x06c, BIT(21), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
0x070, BIT(0), 0);
@@ -484,7 +486,7 @@ static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
0x1a0, 0, 3, BIT(31), 0);
-static struct ccu_common *sun8i_h3_ccu_clks[] = {
+static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
&pll_cpux_clk.common,
&pll_audio_base_clk.common,
&pll_video_clk.common,
@@ -546,7 +548,8 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
- &bus_scr_clk.common,
+ &bus_scr0_clk.common,
+ &bus_scr1_clk.common,
&bus_ephy_clk.common,
&bus_dbg_clk.common,
&ths_clk.common,
@@ -677,7 +680,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
- [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
[CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
[CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
[CLK_THS] = &ths_clk.common.hw,
@@ -730,7 +733,123 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
.num = CLK_NUMBER,
};
-static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+static struct clk_hw_onecell_data sun50i_h5_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
+ [CLK_BUS_SCR1] = &bus_scr1_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_PHY2] = { 0x0cc, BIT(2) },
@@ -790,27 +909,39 @@ static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
- [RST_BUS_SCR] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR1] = { 0x2d8, BIT(21) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
- .ccu_clks = sun8i_h3_ccu_clks,
- .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
+ .ccu_clks = sunxi_h3_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
.hw_clks = &sun8i_h3_hw_clks,
- .resets = sun8i_h3_ccu_resets,
- .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+ .resets = sunxi_h3_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
+};
+
+static const struct sunxi_ccu_desc sun50i_h5_ccu_desc = {
+ .ccu_clks = sunxi_h3_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
+
+ .hw_clks = &sun50i_h5_hw_clks,
+
+ .resets = sunxi_h3_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
};
-static struct ccu_mux_nb sun8i_h3_cpu_nb = {
+static struct ccu_mux_nb sunxi_h3_h5_cpu_nb = {
.common = &cpux_clk.common,
.cm = &cpux_clk.mux,
.delay_us = 1, /* > 8 clock cycles at 24 MHz */
.bypass_index = 1, /* index of 24 MHz oscillator */
};
-static void __init sun8i_h3_ccu_setup(struct device_node *node)
+static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
{
void __iomem *reg;
u32 val;
@@ -823,14 +954,26 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
}
/* Force the PLL-Audio-1x divider to 4 */
- val = readl(reg + SUN8I_H3_PLL_AUDIO_REG);
+ val = readl(reg + SUNXI_H3_H5_PLL_AUDIO_REG);
val &= ~GENMASK(19, 16);
- writel(val | (3 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
+ writel(val | (3 << 16), reg + SUNXI_H3_H5_PLL_AUDIO_REG);
- sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+ sunxi_ccu_probe(node, reg, desc);
ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
- &sun8i_h3_cpu_nb);
+ &sunxi_h3_h5_cpu_nb);
+}
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun8i_h3_ccu_desc);
}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
+
+static void __init sun50i_h5_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun50i_h5_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h5_ccu, "allwinner,sun50i-h5-ccu",
+ sun50i_h5_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
similarity index 82%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.h
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
index 78be712c7487..e5a78cc66d6b 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
@@ -14,11 +14,11 @@
* GNU General Public License for more details.
*/
-#ifndef _CCU_SUN8I_H3_H_
-#define _CCU_SUN8I_H3_H_
+#ifndef _CCU_SUNXI_H3_H5_H_
+#define _CCU_SUNXI_H3_H5_H_
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
#define CLK_PLL_CPUX 0
#define CLK_PLL_AUDIO_BASE 1
@@ -57,6 +57,9 @@
/* And the GPU module clock is exported */
-#define CLK_NUMBER (CLK_GPU + 1)
+/* New clocks imported in H5 */
+/* The SCR1 bus gate is exported */
-#endif /* _CCU_SUN8I_H3_H_ */
+#define CLK_NUMBER (CLK_BUS_SCR1 + 1)
+
+#endif /* _CCU_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 100644
index efb7ba2bd515..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,145 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
-#define _DT_BINDINGS_CLK_SUN8I_H3_H_
-
-#define CLK_CPUX 14
-
-#define CLK_BUS_CE 20
-#define CLK_BUS_DMA 21
-#define CLK_BUS_MMC0 22
-#define CLK_BUS_MMC1 23
-#define CLK_BUS_MMC2 24
-#define CLK_BUS_NAND 25
-#define CLK_BUS_DRAM 26
-#define CLK_BUS_EMAC 27
-#define CLK_BUS_TS 28
-#define CLK_BUS_HSTIMER 29
-#define CLK_BUS_SPI0 30
-#define CLK_BUS_SPI1 31
-#define CLK_BUS_OTG 32
-#define CLK_BUS_EHCI0 33
-#define CLK_BUS_EHCI1 34
-#define CLK_BUS_EHCI2 35
-#define CLK_BUS_EHCI3 36
-#define CLK_BUS_OHCI0 37
-#define CLK_BUS_OHCI1 38
-#define CLK_BUS_OHCI2 39
-#define CLK_BUS_OHCI3 40
-#define CLK_BUS_VE 41
-#define CLK_BUS_TCON0 42
-#define CLK_BUS_TCON1 43
-#define CLK_BUS_DEINTERLACE 44
-#define CLK_BUS_CSI 45
-#define CLK_BUS_TVE 46
-#define CLK_BUS_HDMI 47
-#define CLK_BUS_DE 48
-#define CLK_BUS_GPU 49
-#define CLK_BUS_MSGBOX 50
-#define CLK_BUS_SPINLOCK 51
-#define CLK_BUS_CODEC 52
-#define CLK_BUS_SPDIF 53
-#define CLK_BUS_PIO 54
-#define CLK_BUS_THS 55
-#define CLK_BUS_I2S0 56
-#define CLK_BUS_I2S1 57
-#define CLK_BUS_I2S2 58
-#define CLK_BUS_I2C0 59
-#define CLK_BUS_I2C1 60
-#define CLK_BUS_I2C2 61
-#define CLK_BUS_UART0 62
-#define CLK_BUS_UART1 63
-#define CLK_BUS_UART2 64
-#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
-#define CLK_BUS_EPHY 67
-#define CLK_BUS_DBG 68
-
-#define CLK_THS 69
-#define CLK_NAND 70
-#define CLK_MMC0 71
-#define CLK_MMC0_SAMPLE 72
-#define CLK_MMC0_OUTPUT 73
-#define CLK_MMC1 74
-#define CLK_MMC1_SAMPLE 75
-#define CLK_MMC1_OUTPUT 76
-#define CLK_MMC2 77
-#define CLK_MMC2_SAMPLE 78
-#define CLK_MMC2_OUTPUT 79
-#define CLK_TS 80
-#define CLK_CE 81
-#define CLK_SPI0 82
-#define CLK_SPI1 83
-#define CLK_I2S0 84
-#define CLK_I2S1 85
-#define CLK_I2S2 86
-#define CLK_SPDIF 87
-#define CLK_USB_PHY0 88
-#define CLK_USB_PHY1 89
-#define CLK_USB_PHY2 90
-#define CLK_USB_PHY3 91
-#define CLK_USB_OHCI0 92
-#define CLK_USB_OHCI1 93
-#define CLK_USB_OHCI2 94
-#define CLK_USB_OHCI3 95
-
-#define CLK_DRAM_VE 97
-#define CLK_DRAM_CSI 98
-#define CLK_DRAM_DEINTERLACE 99
-#define CLK_DRAM_TS 100
-#define CLK_DE 101
-#define CLK_TCON0 102
-#define CLK_TVE 103
-#define CLK_DEINTERLACE 104
-#define CLK_CSI_MISC 105
-#define CLK_CSI_SCLK 106
-#define CLK_CSI_MCLK 107
-#define CLK_VE 108
-#define CLK_AC_DIG 109
-#define CLK_AVS 110
-#define CLK_HDMI 111
-#define CLK_HDMI_DDC 112
-
-#define CLK_GPU 114
-
-#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/clock/sunxi-h3-h5-ccu.h b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
new file mode 100644
index 000000000000..4899eacef71d
--- /dev/null
+++ b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
@@ -0,0 +1,148 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
+
+#define CLK_CPUX 14
+
+#define CLK_BUS_CE 20
+#define CLK_BUS_DMA 21
+#define CLK_BUS_MMC0 22
+#define CLK_BUS_MMC1 23
+#define CLK_BUS_MMC2 24
+#define CLK_BUS_NAND 25
+#define CLK_BUS_DRAM 26
+#define CLK_BUS_EMAC 27
+#define CLK_BUS_TS 28
+#define CLK_BUS_HSTIMER 29
+#define CLK_BUS_SPI0 30
+#define CLK_BUS_SPI1 31
+#define CLK_BUS_OTG 32
+#define CLK_BUS_EHCI0 33
+#define CLK_BUS_EHCI1 34
+#define CLK_BUS_EHCI2 35
+#define CLK_BUS_EHCI3 36
+#define CLK_BUS_OHCI0 37
+#define CLK_BUS_OHCI1 38
+#define CLK_BUS_OHCI2 39
+#define CLK_BUS_OHCI3 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_TCON0 42
+#define CLK_BUS_TCON1 43
+#define CLK_BUS_DEINTERLACE 44
+#define CLK_BUS_CSI 45
+#define CLK_BUS_TVE 46
+#define CLK_BUS_HDMI 47
+#define CLK_BUS_DE 48
+#define CLK_BUS_GPU 49
+#define CLK_BUS_MSGBOX 50
+#define CLK_BUS_SPINLOCK 51
+#define CLK_BUS_CODEC 52
+#define CLK_BUS_SPDIF 53
+#define CLK_BUS_PIO 54
+#define CLK_BUS_THS 55
+#define CLK_BUS_I2S0 56
+#define CLK_BUS_I2S1 57
+#define CLK_BUS_I2S2 58
+#define CLK_BUS_I2C0 59
+#define CLK_BUS_I2C1 60
+#define CLK_BUS_I2C2 61
+#define CLK_BUS_UART0 62
+#define CLK_BUS_UART1 63
+#define CLK_BUS_UART2 64
+#define CLK_BUS_UART3 65
+#define CLK_BUS_SCR0 66
+#define CLK_BUS_EPHY 67
+#define CLK_BUS_DBG 68
+
+#define CLK_THS 69
+#define CLK_NAND 70
+#define CLK_MMC0 71
+#define CLK_MMC0_SAMPLE 72
+#define CLK_MMC0_OUTPUT 73
+#define CLK_MMC1 74
+#define CLK_MMC1_SAMPLE 75
+#define CLK_MMC1_OUTPUT 76
+#define CLK_MMC2 77
+#define CLK_MMC2_SAMPLE 78
+#define CLK_MMC2_OUTPUT 79
+#define CLK_TS 80
+#define CLK_CE 81
+#define CLK_SPI0 82
+#define CLK_SPI1 83
+#define CLK_I2S0 84
+#define CLK_I2S1 85
+#define CLK_I2S2 86
+#define CLK_SPDIF 87
+#define CLK_USB_PHY0 88
+#define CLK_USB_PHY1 89
+#define CLK_USB_PHY2 90
+#define CLK_USB_PHY3 91
+#define CLK_USB_OHCI0 92
+#define CLK_USB_OHCI1 93
+#define CLK_USB_OHCI2 94
+#define CLK_USB_OHCI3 95
+
+#define CLK_DRAM_VE 97
+#define CLK_DRAM_CSI 98
+#define CLK_DRAM_DEINTERLACE 99
+#define CLK_DRAM_TS 100
+#define CLK_DE 101
+#define CLK_TCON0 102
+#define CLK_TVE 103
+#define CLK_DEINTERLACE 104
+#define CLK_CSI_MISC 105
+#define CLK_CSI_SCLK 106
+#define CLK_CSI_MCLK 107
+#define CLK_VE 108
+#define CLK_AC_DIG 109
+#define CLK_AVS 110
+#define CLK_HDMI 111
+#define CLK_HDMI_DDC 112
+
+#define CLK_GPU 114
+
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
+#endif /* _DT_BINDINGS_CLK_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 100644
index 6b7af80c26ec..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
-#define _DT_BINDINGS_RST_SUN8I_H3_H_
-
-#define RST_USB_PHY0 0
-#define RST_USB_PHY1 1
-#define RST_USB_PHY2 2
-#define RST_USB_PHY3 3
-
-#define RST_MBUS 4
-
-#define RST_BUS_CE 5
-#define RST_BUS_DMA 6
-#define RST_BUS_MMC0 7
-#define RST_BUS_MMC1 8
-#define RST_BUS_MMC2 9
-#define RST_BUS_NAND 10
-#define RST_BUS_DRAM 11
-#define RST_BUS_EMAC 12
-#define RST_BUS_TS 13
-#define RST_BUS_HSTIMER 14
-#define RST_BUS_SPI0 15
-#define RST_BUS_SPI1 16
-#define RST_BUS_OTG 17
-#define RST_BUS_EHCI0 18
-#define RST_BUS_EHCI1 19
-#define RST_BUS_EHCI2 20
-#define RST_BUS_EHCI3 21
-#define RST_BUS_OHCI0 22
-#define RST_BUS_OHCI1 23
-#define RST_BUS_OHCI2 24
-#define RST_BUS_OHCI3 25
-#define RST_BUS_VE 26
-#define RST_BUS_TCON0 27
-#define RST_BUS_TCON1 28
-#define RST_BUS_DEINTERLACE 29
-#define RST_BUS_CSI 30
-#define RST_BUS_TVE 31
-#define RST_BUS_HDMI0 32
-#define RST_BUS_HDMI1 33
-#define RST_BUS_DE 34
-#define RST_BUS_GPU 35
-#define RST_BUS_MSGBOX 36
-#define RST_BUS_SPINLOCK 37
-#define RST_BUS_DBG 38
-#define RST_BUS_EPHY 39
-#define RST_BUS_CODEC 40
-#define RST_BUS_SPDIF 41
-#define RST_BUS_THS 42
-#define RST_BUS_I2S0 43
-#define RST_BUS_I2S1 44
-#define RST_BUS_I2S2 45
-#define RST_BUS_I2C0 46
-#define RST_BUS_I2C1 47
-#define RST_BUS_I2C2 48
-#define RST_BUS_UART0 49
-#define RST_BUS_UART1 50
-#define RST_BUS_UART2 51
-#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
-
-#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sunxi-h3-h5-ccu.h b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
new file mode 100644
index 000000000000..1084c157c062
--- /dev/null
+++ b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
@@ -0,0 +1,106 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RST_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_RST_SUNXI_H3_H5_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_USB_PHY2 2
+#define RST_USB_PHY3 3
+
+#define RST_MBUS 4
+
+#define RST_BUS_CE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MMC0 7
+#define RST_BUS_MMC1 8
+#define RST_BUS_MMC2 9
+#define RST_BUS_NAND 10
+#define RST_BUS_DRAM 11
+#define RST_BUS_EMAC 12
+#define RST_BUS_TS 13
+#define RST_BUS_HSTIMER 14
+#define RST_BUS_SPI0 15
+#define RST_BUS_SPI1 16
+#define RST_BUS_OTG 17
+#define RST_BUS_EHCI0 18
+#define RST_BUS_EHCI1 19
+#define RST_BUS_EHCI2 20
+#define RST_BUS_EHCI3 21
+#define RST_BUS_OHCI0 22
+#define RST_BUS_OHCI1 23
+#define RST_BUS_OHCI2 24
+#define RST_BUS_OHCI3 25
+#define RST_BUS_VE 26
+#define RST_BUS_TCON0 27
+#define RST_BUS_TCON1 28
+#define RST_BUS_DEINTERLACE 29
+#define RST_BUS_CSI 30
+#define RST_BUS_TVE 31
+#define RST_BUS_HDMI0 32
+#define RST_BUS_HDMI1 33
+#define RST_BUS_DE 34
+#define RST_BUS_GPU 35
+#define RST_BUS_MSGBOX 36
+#define RST_BUS_SPINLOCK 37
+#define RST_BUS_DBG 38
+#define RST_BUS_EPHY 39
+#define RST_BUS_CODEC 40
+#define RST_BUS_SPDIF 41
+#define RST_BUS_THS 42
+#define RST_BUS_I2S0 43
+#define RST_BUS_I2S1 44
+#define RST_BUS_I2S2 45
+#define RST_BUS_I2C0 46
+#define RST_BUS_I2C1 47
+#define RST_BUS_I2C2 48
+#define RST_BUS_UART0 49
+#define RST_BUS_UART1 50
+#define RST_BUS_UART2 51
+#define RST_BUS_UART3 52
+#define RST_BUS_SCR0 53
+
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
+
+#endif /* _DT_BINDINGS_RST_SUNXI_H3_H5_H_ */
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 3/9] clk: sunxi-ng: add support for Allwinner H5 SoC
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
clocks removed (for new MMC controller) and a new bus gate/reset
imported.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
A giant rewrite since v1.
It now do not use a dedicated driver for H5, but altered the CCU driver
of H3 to support H5.
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
drivers/clk/sunxi-ng/Kconfig | 6 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++++++++++++++---
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +----------------
include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 148 +++++++++++++++++
include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +-----------
include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 106 ++++++++++++
9 files changed, 431 insertions(+), 276 deletions(-)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
mode change 100644 => 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
create mode 100644 include/dt-bindings/clock/sunxi-h3-h5-ccu.h
mode change 100644 => 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
create mode 100644 include/dt-bindings/reset/sunxi-h3-h5-ccu.h
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index f6032cf63f12..a33a4a5ecffa 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -9,6 +9,7 @@ Required properties :
- "allwinner,sun8i-h3-ccu"
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun50i-a64-ccu"
+ - "allwinner,sun50i-h5-ccu"
- reg: Must contain the registers base address and length
- clocks: phandle to the oscillators feeding the CCU. Two are needed:
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 71f11cd1647b..bdf18e846731 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -108,8 +108,8 @@ config SUN8I_A33_CCU
select SUNXI_CCU_PHASE
default MACH_SUN8I
-config SUN8I_H3_CCU
- bool "Support for the Allwinner H3 CCU"
+config SUNXI_H3_H5_CCU
+ bool "Support for the Allwinner H3/H5 CCU"
select SUNXI_CCU_DIV
select SUNXI_CCU_NK
select SUNXI_CCU_NKM
@@ -117,7 +117,7 @@ config SUN8I_H3_CCU
select SUNXI_CCU_NM
select SUNXI_CCU_MP
select SUNXI_CCU_PHASE
- default MACH_SUN8I
+ default MACH_SUN8I || (ARM64 && ARCH_SUNXI)
config SUN8I_V3S_CCU
bool "Support for the Allwinner V3s CCU"
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index a8afdf9c7668..cdc3359abbfe 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,5 +23,5 @@ obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
obj-$(CONFIG_SUN6I_A31_CCU) += ccu-sun6i-a31.o
obj-$(CONFIG_SUN8I_A23_CCU) += ccu-sun8i-a23.o
obj-$(CONFIG_SUN8I_A33_CCU) += ccu-sun8i-a33.o
-obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
+obj-$(CONFIG_SUNXI_H3_H5_CCU) += ccu-sunxi-h3-h5.o
obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
similarity index 80%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.c
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
index a26c8a19fe93..b7b9f85f5c9f 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
@@ -27,7 +27,7 @@
#include "ccu_nm.h"
#include "ccu_phase.h"
-#include "ccu-sun8i-h3.h"
+#include "ccu-sunxi-h3-h5.h"
static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
"osc24M", 0x000,
@@ -47,7 +47,7 @@ static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
* We don't have any need for the variable divider for now, so we just
* hardcode it to match with the clock names
*/
-#define SUN8I_H3_PLL_AUDIO_REG 0x008
+#define SUNXI_H3_H5_PLL_AUDIO_REG 0x008
static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
"osc24M", 0x008,
@@ -300,8 +300,10 @@ static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
-static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_scr1_clk, "bus-scr1", "apb2",
+ 0x06c, BIT(21), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
0x070, BIT(0), 0);
@@ -484,7 +486,7 @@ static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
0x1a0, 0, 3, BIT(31), 0);
-static struct ccu_common *sun8i_h3_ccu_clks[] = {
+static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
&pll_cpux_clk.common,
&pll_audio_base_clk.common,
&pll_video_clk.common,
@@ -546,7 +548,8 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
- &bus_scr_clk.common,
+ &bus_scr0_clk.common,
+ &bus_scr1_clk.common,
&bus_ephy_clk.common,
&bus_dbg_clk.common,
&ths_clk.common,
@@ -677,7 +680,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
- [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
[CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
[CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
[CLK_THS] = &ths_clk.common.hw,
@@ -730,7 +733,123 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
.num = CLK_NUMBER,
};
-static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+static struct clk_hw_onecell_data sun50i_h5_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
+ [CLK_BUS_SCR1] = &bus_scr1_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_PHY2] = { 0x0cc, BIT(2) },
@@ -790,27 +909,39 @@ static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
- [RST_BUS_SCR] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR1] = { 0x2d8, BIT(21) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
- .ccu_clks = sun8i_h3_ccu_clks,
- .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
+ .ccu_clks = sunxi_h3_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
.hw_clks = &sun8i_h3_hw_clks,
- .resets = sun8i_h3_ccu_resets,
- .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+ .resets = sunxi_h3_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
+};
+
+static const struct sunxi_ccu_desc sun50i_h5_ccu_desc = {
+ .ccu_clks = sunxi_h3_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
+
+ .hw_clks = &sun50i_h5_hw_clks,
+
+ .resets = sunxi_h3_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
};
-static struct ccu_mux_nb sun8i_h3_cpu_nb = {
+static struct ccu_mux_nb sunxi_h3_h5_cpu_nb = {
.common = &cpux_clk.common,
.cm = &cpux_clk.mux,
.delay_us = 1, /* > 8 clock cycles at 24 MHz */
.bypass_index = 1, /* index of 24 MHz oscillator */
};
-static void __init sun8i_h3_ccu_setup(struct device_node *node)
+static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
{
void __iomem *reg;
u32 val;
@@ -823,14 +954,26 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
}
/* Force the PLL-Audio-1x divider to 4 */
- val = readl(reg + SUN8I_H3_PLL_AUDIO_REG);
+ val = readl(reg + SUNXI_H3_H5_PLL_AUDIO_REG);
val &= ~GENMASK(19, 16);
- writel(val | (3 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
+ writel(val | (3 << 16), reg + SUNXI_H3_H5_PLL_AUDIO_REG);
- sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+ sunxi_ccu_probe(node, reg, desc);
ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
- &sun8i_h3_cpu_nb);
+ &sunxi_h3_h5_cpu_nb);
+}
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun8i_h3_ccu_desc);
}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
+
+static void __init sun50i_h5_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun50i_h5_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h5_ccu, "allwinner,sun50i-h5-ccu",
+ sun50i_h5_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
similarity index 82%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.h
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
index 78be712c7487..e5a78cc66d6b 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
@@ -14,11 +14,11 @@
* GNU General Public License for more details.
*/
-#ifndef _CCU_SUN8I_H3_H_
-#define _CCU_SUN8I_H3_H_
+#ifndef _CCU_SUNXI_H3_H5_H_
+#define _CCU_SUNXI_H3_H5_H_
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
#define CLK_PLL_CPUX 0
#define CLK_PLL_AUDIO_BASE 1
@@ -57,6 +57,9 @@
/* And the GPU module clock is exported */
-#define CLK_NUMBER (CLK_GPU + 1)
+/* New clocks imported in H5 */
+/* The SCR1 bus gate is exported */
-#endif /* _CCU_SUN8I_H3_H_ */
+#define CLK_NUMBER (CLK_BUS_SCR1 + 1)
+
+#endif /* _CCU_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 100644
index efb7ba2bd515..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,145 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
-#define _DT_BINDINGS_CLK_SUN8I_H3_H_
-
-#define CLK_CPUX 14
-
-#define CLK_BUS_CE 20
-#define CLK_BUS_DMA 21
-#define CLK_BUS_MMC0 22
-#define CLK_BUS_MMC1 23
-#define CLK_BUS_MMC2 24
-#define CLK_BUS_NAND 25
-#define CLK_BUS_DRAM 26
-#define CLK_BUS_EMAC 27
-#define CLK_BUS_TS 28
-#define CLK_BUS_HSTIMER 29
-#define CLK_BUS_SPI0 30
-#define CLK_BUS_SPI1 31
-#define CLK_BUS_OTG 32
-#define CLK_BUS_EHCI0 33
-#define CLK_BUS_EHCI1 34
-#define CLK_BUS_EHCI2 35
-#define CLK_BUS_EHCI3 36
-#define CLK_BUS_OHCI0 37
-#define CLK_BUS_OHCI1 38
-#define CLK_BUS_OHCI2 39
-#define CLK_BUS_OHCI3 40
-#define CLK_BUS_VE 41
-#define CLK_BUS_TCON0 42
-#define CLK_BUS_TCON1 43
-#define CLK_BUS_DEINTERLACE 44
-#define CLK_BUS_CSI 45
-#define CLK_BUS_TVE 46
-#define CLK_BUS_HDMI 47
-#define CLK_BUS_DE 48
-#define CLK_BUS_GPU 49
-#define CLK_BUS_MSGBOX 50
-#define CLK_BUS_SPINLOCK 51
-#define CLK_BUS_CODEC 52
-#define CLK_BUS_SPDIF 53
-#define CLK_BUS_PIO 54
-#define CLK_BUS_THS 55
-#define CLK_BUS_I2S0 56
-#define CLK_BUS_I2S1 57
-#define CLK_BUS_I2S2 58
-#define CLK_BUS_I2C0 59
-#define CLK_BUS_I2C1 60
-#define CLK_BUS_I2C2 61
-#define CLK_BUS_UART0 62
-#define CLK_BUS_UART1 63
-#define CLK_BUS_UART2 64
-#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
-#define CLK_BUS_EPHY 67
-#define CLK_BUS_DBG 68
-
-#define CLK_THS 69
-#define CLK_NAND 70
-#define CLK_MMC0 71
-#define CLK_MMC0_SAMPLE 72
-#define CLK_MMC0_OUTPUT 73
-#define CLK_MMC1 74
-#define CLK_MMC1_SAMPLE 75
-#define CLK_MMC1_OUTPUT 76
-#define CLK_MMC2 77
-#define CLK_MMC2_SAMPLE 78
-#define CLK_MMC2_OUTPUT 79
-#define CLK_TS 80
-#define CLK_CE 81
-#define CLK_SPI0 82
-#define CLK_SPI1 83
-#define CLK_I2S0 84
-#define CLK_I2S1 85
-#define CLK_I2S2 86
-#define CLK_SPDIF 87
-#define CLK_USB_PHY0 88
-#define CLK_USB_PHY1 89
-#define CLK_USB_PHY2 90
-#define CLK_USB_PHY3 91
-#define CLK_USB_OHCI0 92
-#define CLK_USB_OHCI1 93
-#define CLK_USB_OHCI2 94
-#define CLK_USB_OHCI3 95
-
-#define CLK_DRAM_VE 97
-#define CLK_DRAM_CSI 98
-#define CLK_DRAM_DEINTERLACE 99
-#define CLK_DRAM_TS 100
-#define CLK_DE 101
-#define CLK_TCON0 102
-#define CLK_TVE 103
-#define CLK_DEINTERLACE 104
-#define CLK_CSI_MISC 105
-#define CLK_CSI_SCLK 106
-#define CLK_CSI_MCLK 107
-#define CLK_VE 108
-#define CLK_AC_DIG 109
-#define CLK_AVS 110
-#define CLK_HDMI 111
-#define CLK_HDMI_DDC 112
-
-#define CLK_GPU 114
-
-#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/clock/sunxi-h3-h5-ccu.h b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
new file mode 100644
index 000000000000..4899eacef71d
--- /dev/null
+++ b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
@@ -0,0 +1,148 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
+
+#define CLK_CPUX 14
+
+#define CLK_BUS_CE 20
+#define CLK_BUS_DMA 21
+#define CLK_BUS_MMC0 22
+#define CLK_BUS_MMC1 23
+#define CLK_BUS_MMC2 24
+#define CLK_BUS_NAND 25
+#define CLK_BUS_DRAM 26
+#define CLK_BUS_EMAC 27
+#define CLK_BUS_TS 28
+#define CLK_BUS_HSTIMER 29
+#define CLK_BUS_SPI0 30
+#define CLK_BUS_SPI1 31
+#define CLK_BUS_OTG 32
+#define CLK_BUS_EHCI0 33
+#define CLK_BUS_EHCI1 34
+#define CLK_BUS_EHCI2 35
+#define CLK_BUS_EHCI3 36
+#define CLK_BUS_OHCI0 37
+#define CLK_BUS_OHCI1 38
+#define CLK_BUS_OHCI2 39
+#define CLK_BUS_OHCI3 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_TCON0 42
+#define CLK_BUS_TCON1 43
+#define CLK_BUS_DEINTERLACE 44
+#define CLK_BUS_CSI 45
+#define CLK_BUS_TVE 46
+#define CLK_BUS_HDMI 47
+#define CLK_BUS_DE 48
+#define CLK_BUS_GPU 49
+#define CLK_BUS_MSGBOX 50
+#define CLK_BUS_SPINLOCK 51
+#define CLK_BUS_CODEC 52
+#define CLK_BUS_SPDIF 53
+#define CLK_BUS_PIO 54
+#define CLK_BUS_THS 55
+#define CLK_BUS_I2S0 56
+#define CLK_BUS_I2S1 57
+#define CLK_BUS_I2S2 58
+#define CLK_BUS_I2C0 59
+#define CLK_BUS_I2C1 60
+#define CLK_BUS_I2C2 61
+#define CLK_BUS_UART0 62
+#define CLK_BUS_UART1 63
+#define CLK_BUS_UART2 64
+#define CLK_BUS_UART3 65
+#define CLK_BUS_SCR0 66
+#define CLK_BUS_EPHY 67
+#define CLK_BUS_DBG 68
+
+#define CLK_THS 69
+#define CLK_NAND 70
+#define CLK_MMC0 71
+#define CLK_MMC0_SAMPLE 72
+#define CLK_MMC0_OUTPUT 73
+#define CLK_MMC1 74
+#define CLK_MMC1_SAMPLE 75
+#define CLK_MMC1_OUTPUT 76
+#define CLK_MMC2 77
+#define CLK_MMC2_SAMPLE 78
+#define CLK_MMC2_OUTPUT 79
+#define CLK_TS 80
+#define CLK_CE 81
+#define CLK_SPI0 82
+#define CLK_SPI1 83
+#define CLK_I2S0 84
+#define CLK_I2S1 85
+#define CLK_I2S2 86
+#define CLK_SPDIF 87
+#define CLK_USB_PHY0 88
+#define CLK_USB_PHY1 89
+#define CLK_USB_PHY2 90
+#define CLK_USB_PHY3 91
+#define CLK_USB_OHCI0 92
+#define CLK_USB_OHCI1 93
+#define CLK_USB_OHCI2 94
+#define CLK_USB_OHCI3 95
+
+#define CLK_DRAM_VE 97
+#define CLK_DRAM_CSI 98
+#define CLK_DRAM_DEINTERLACE 99
+#define CLK_DRAM_TS 100
+#define CLK_DE 101
+#define CLK_TCON0 102
+#define CLK_TVE 103
+#define CLK_DEINTERLACE 104
+#define CLK_CSI_MISC 105
+#define CLK_CSI_SCLK 106
+#define CLK_CSI_MCLK 107
+#define CLK_VE 108
+#define CLK_AC_DIG 109
+#define CLK_AVS 110
+#define CLK_HDMI 111
+#define CLK_HDMI_DDC 112
+
+#define CLK_GPU 114
+
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
+#endif /* _DT_BINDINGS_CLK_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 100644
index 6b7af80c26ec..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
-#define _DT_BINDINGS_RST_SUN8I_H3_H_
-
-#define RST_USB_PHY0 0
-#define RST_USB_PHY1 1
-#define RST_USB_PHY2 2
-#define RST_USB_PHY3 3
-
-#define RST_MBUS 4
-
-#define RST_BUS_CE 5
-#define RST_BUS_DMA 6
-#define RST_BUS_MMC0 7
-#define RST_BUS_MMC1 8
-#define RST_BUS_MMC2 9
-#define RST_BUS_NAND 10
-#define RST_BUS_DRAM 11
-#define RST_BUS_EMAC 12
-#define RST_BUS_TS 13
-#define RST_BUS_HSTIMER 14
-#define RST_BUS_SPI0 15
-#define RST_BUS_SPI1 16
-#define RST_BUS_OTG 17
-#define RST_BUS_EHCI0 18
-#define RST_BUS_EHCI1 19
-#define RST_BUS_EHCI2 20
-#define RST_BUS_EHCI3 21
-#define RST_BUS_OHCI0 22
-#define RST_BUS_OHCI1 23
-#define RST_BUS_OHCI2 24
-#define RST_BUS_OHCI3 25
-#define RST_BUS_VE 26
-#define RST_BUS_TCON0 27
-#define RST_BUS_TCON1 28
-#define RST_BUS_DEINTERLACE 29
-#define RST_BUS_CSI 30
-#define RST_BUS_TVE 31
-#define RST_BUS_HDMI0 32
-#define RST_BUS_HDMI1 33
-#define RST_BUS_DE 34
-#define RST_BUS_GPU 35
-#define RST_BUS_MSGBOX 36
-#define RST_BUS_SPINLOCK 37
-#define RST_BUS_DBG 38
-#define RST_BUS_EPHY 39
-#define RST_BUS_CODEC 40
-#define RST_BUS_SPDIF 41
-#define RST_BUS_THS 42
-#define RST_BUS_I2S0 43
-#define RST_BUS_I2S1 44
-#define RST_BUS_I2S2 45
-#define RST_BUS_I2C0 46
-#define RST_BUS_I2C1 47
-#define RST_BUS_I2C2 48
-#define RST_BUS_UART0 49
-#define RST_BUS_UART1 50
-#define RST_BUS_UART2 51
-#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
-
-#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sunxi-h3-h5-ccu.h b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
new file mode 100644
index 000000000000..1084c157c062
--- /dev/null
+++ b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
@@ -0,0 +1,106 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RST_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_RST_SUNXI_H3_H5_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_USB_PHY2 2
+#define RST_USB_PHY3 3
+
+#define RST_MBUS 4
+
+#define RST_BUS_CE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MMC0 7
+#define RST_BUS_MMC1 8
+#define RST_BUS_MMC2 9
+#define RST_BUS_NAND 10
+#define RST_BUS_DRAM 11
+#define RST_BUS_EMAC 12
+#define RST_BUS_TS 13
+#define RST_BUS_HSTIMER 14
+#define RST_BUS_SPI0 15
+#define RST_BUS_SPI1 16
+#define RST_BUS_OTG 17
+#define RST_BUS_EHCI0 18
+#define RST_BUS_EHCI1 19
+#define RST_BUS_EHCI2 20
+#define RST_BUS_EHCI3 21
+#define RST_BUS_OHCI0 22
+#define RST_BUS_OHCI1 23
+#define RST_BUS_OHCI2 24
+#define RST_BUS_OHCI3 25
+#define RST_BUS_VE 26
+#define RST_BUS_TCON0 27
+#define RST_BUS_TCON1 28
+#define RST_BUS_DEINTERLACE 29
+#define RST_BUS_CSI 30
+#define RST_BUS_TVE 31
+#define RST_BUS_HDMI0 32
+#define RST_BUS_HDMI1 33
+#define RST_BUS_DE 34
+#define RST_BUS_GPU 35
+#define RST_BUS_MSGBOX 36
+#define RST_BUS_SPINLOCK 37
+#define RST_BUS_DBG 38
+#define RST_BUS_EPHY 39
+#define RST_BUS_CODEC 40
+#define RST_BUS_SPDIF 41
+#define RST_BUS_THS 42
+#define RST_BUS_I2S0 43
+#define RST_BUS_I2S1 44
+#define RST_BUS_I2S2 45
+#define RST_BUS_I2C0 46
+#define RST_BUS_I2C1 47
+#define RST_BUS_I2C2 48
+#define RST_BUS_UART0 49
+#define RST_BUS_UART1 50
+#define RST_BUS_UART2 51
+#define RST_BUS_UART3 52
+#define RST_BUS_SCR0 53
+
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
+
+#endif /* _DT_BINDINGS_RST_SUNXI_H3_H5_H_ */
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 3/9] clk: sunxi-ng: add support for Allwinner H5 SoC
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
clocks removed (for new MMC controller) and a new bus gate/reset
imported.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
A giant rewrite since v1.
It now do not use a dedicated driver for H5, but altered the CCU driver
of H3 to support H5.
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
drivers/clk/sunxi-ng/Kconfig | 6 +-
drivers/clk/sunxi-ng/Makefile | 2 +-
.../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++++++++++++++---
.../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +----------------
include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 148 +++++++++++++++++
include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +-----------
include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 106 ++++++++++++
9 files changed, 431 insertions(+), 276 deletions(-)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
mode change 100644 => 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
create mode 100644 include/dt-bindings/clock/sunxi-h3-h5-ccu.h
mode change 100644 => 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
create mode 100644 include/dt-bindings/reset/sunxi-h3-h5-ccu.h
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index f6032cf63f12..a33a4a5ecffa 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -9,6 +9,7 @@ Required properties :
- "allwinner,sun8i-h3-ccu"
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun50i-a64-ccu"
+ - "allwinner,sun50i-h5-ccu"
- reg: Must contain the registers base address and length
- clocks: phandle to the oscillators feeding the CCU. Two are needed:
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 71f11cd1647b..bdf18e846731 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -108,8 +108,8 @@ config SUN8I_A33_CCU
select SUNXI_CCU_PHASE
default MACH_SUN8I
-config SUN8I_H3_CCU
- bool "Support for the Allwinner H3 CCU"
+config SUNXI_H3_H5_CCU
+ bool "Support for the Allwinner H3/H5 CCU"
select SUNXI_CCU_DIV
select SUNXI_CCU_NK
select SUNXI_CCU_NKM
@@ -117,7 +117,7 @@ config SUN8I_H3_CCU
select SUNXI_CCU_NM
select SUNXI_CCU_MP
select SUNXI_CCU_PHASE
- default MACH_SUN8I
+ default MACH_SUN8I || (ARM64 && ARCH_SUNXI)
config SUN8I_V3S_CCU
bool "Support for the Allwinner V3s CCU"
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index a8afdf9c7668..cdc3359abbfe 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,5 +23,5 @@ obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
obj-$(CONFIG_SUN6I_A31_CCU) += ccu-sun6i-a31.o
obj-$(CONFIG_SUN8I_A23_CCU) += ccu-sun8i-a23.o
obj-$(CONFIG_SUN8I_A33_CCU) += ccu-sun8i-a33.o
-obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
+obj-$(CONFIG_SUNXI_H3_H5_CCU) += ccu-sunxi-h3-h5.o
obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
similarity index 80%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.c
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
index a26c8a19fe93..b7b9f85f5c9f 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.c
@@ -27,7 +27,7 @@
#include "ccu_nm.h"
#include "ccu_phase.h"
-#include "ccu-sun8i-h3.h"
+#include "ccu-sunxi-h3-h5.h"
static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
"osc24M", 0x000,
@@ -47,7 +47,7 @@ static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
* We don't have any need for the variable divider for now, so we just
* hardcode it to match with the clock names
*/
-#define SUN8I_H3_PLL_AUDIO_REG 0x008
+#define SUNXI_H3_H5_PLL_AUDIO_REG 0x008
static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
"osc24M", 0x008,
@@ -300,8 +300,10 @@ static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
-static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_scr1_clk, "bus-scr1", "apb2",
+ 0x06c, BIT(21), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
0x070, BIT(0), 0);
@@ -484,7 +486,7 @@ static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
0x1a0, 0, 3, BIT(31), 0);
-static struct ccu_common *sun8i_h3_ccu_clks[] = {
+static struct ccu_common *sunxi_h3_h5_ccu_clks[] = {
&pll_cpux_clk.common,
&pll_audio_base_clk.common,
&pll_video_clk.common,
@@ -546,7 +548,8 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
- &bus_scr_clk.common,
+ &bus_scr0_clk.common,
+ &bus_scr1_clk.common,
&bus_ephy_clk.common,
&bus_dbg_clk.common,
&ths_clk.common,
@@ -677,7 +680,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
- [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
[CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
[CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
[CLK_THS] = &ths_clk.common.hw,
@@ -730,7 +733,123 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
.num = CLK_NUMBER,
};
-static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+static struct clk_hw_onecell_data sun50i_h5_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
+ [CLK_BUS_SCR1] = &bus_scr1_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sunxi_h3_h5_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_PHY2] = { 0x0cc, BIT(2) },
@@ -790,27 +909,39 @@ static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
- [RST_BUS_SCR] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR1] = { 0x2d8, BIT(21) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
- .ccu_clks = sun8i_h3_ccu_clks,
- .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
+ .ccu_clks = sunxi_h3_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
.hw_clks = &sun8i_h3_hw_clks,
- .resets = sun8i_h3_ccu_resets,
- .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+ .resets = sunxi_h3_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
+};
+
+static const struct sunxi_ccu_desc sun50i_h5_ccu_desc = {
+ .ccu_clks = sunxi_h3_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sunxi_h3_h5_ccu_clks),
+
+ .hw_clks = &sun50i_h5_hw_clks,
+
+ .resets = sunxi_h3_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sunxi_h3_h5_ccu_resets),
};
-static struct ccu_mux_nb sun8i_h3_cpu_nb = {
+static struct ccu_mux_nb sunxi_h3_h5_cpu_nb = {
.common = &cpux_clk.common,
.cm = &cpux_clk.mux,
.delay_us = 1, /* > 8 clock cycles at 24 MHz */
.bypass_index = 1, /* index of 24 MHz oscillator */
};
-static void __init sun8i_h3_ccu_setup(struct device_node *node)
+static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
{
void __iomem *reg;
u32 val;
@@ -823,14 +954,26 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
}
/* Force the PLL-Audio-1x divider to 4 */
- val = readl(reg + SUN8I_H3_PLL_AUDIO_REG);
+ val = readl(reg + SUNXI_H3_H5_PLL_AUDIO_REG);
val &= ~GENMASK(19, 16);
- writel(val | (3 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
+ writel(val | (3 << 16), reg + SUNXI_H3_H5_PLL_AUDIO_REG);
- sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+ sunxi_ccu_probe(node, reg, desc);
ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
- &sun8i_h3_cpu_nb);
+ &sunxi_h3_h5_cpu_nb);
+}
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun8i_h3_ccu_desc);
}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
+
+static void __init sun50i_h5_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun50i_h5_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h5_ccu, "allwinner,sun50i-h5-ccu",
+ sun50i_h5_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
similarity index 82%
rename from drivers/clk/sunxi-ng/ccu-sun8i-h3.h
rename to drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
index 78be712c7487..e5a78cc66d6b 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sunxi-h3-h5.h
@@ -14,11 +14,11 @@
* GNU General Public License for more details.
*/
-#ifndef _CCU_SUN8I_H3_H_
-#define _CCU_SUN8I_H3_H_
+#ifndef _CCU_SUNXI_H3_H5_H_
+#define _CCU_SUNXI_H3_H5_H_
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
#define CLK_PLL_CPUX 0
#define CLK_PLL_AUDIO_BASE 1
@@ -57,6 +57,9 @@
/* And the GPU module clock is exported */
-#define CLK_NUMBER (CLK_GPU + 1)
+/* New clocks imported in H5 */
+/* The SCR1 bus gate is exported */
-#endif /* _CCU_SUN8I_H3_H_ */
+#define CLK_NUMBER (CLK_BUS_SCR1 + 1)
+
+#endif /* _CCU_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 100644
index efb7ba2bd515..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,145 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
-#define _DT_BINDINGS_CLK_SUN8I_H3_H_
-
-#define CLK_CPUX 14
-
-#define CLK_BUS_CE 20
-#define CLK_BUS_DMA 21
-#define CLK_BUS_MMC0 22
-#define CLK_BUS_MMC1 23
-#define CLK_BUS_MMC2 24
-#define CLK_BUS_NAND 25
-#define CLK_BUS_DRAM 26
-#define CLK_BUS_EMAC 27
-#define CLK_BUS_TS 28
-#define CLK_BUS_HSTIMER 29
-#define CLK_BUS_SPI0 30
-#define CLK_BUS_SPI1 31
-#define CLK_BUS_OTG 32
-#define CLK_BUS_EHCI0 33
-#define CLK_BUS_EHCI1 34
-#define CLK_BUS_EHCI2 35
-#define CLK_BUS_EHCI3 36
-#define CLK_BUS_OHCI0 37
-#define CLK_BUS_OHCI1 38
-#define CLK_BUS_OHCI2 39
-#define CLK_BUS_OHCI3 40
-#define CLK_BUS_VE 41
-#define CLK_BUS_TCON0 42
-#define CLK_BUS_TCON1 43
-#define CLK_BUS_DEINTERLACE 44
-#define CLK_BUS_CSI 45
-#define CLK_BUS_TVE 46
-#define CLK_BUS_HDMI 47
-#define CLK_BUS_DE 48
-#define CLK_BUS_GPU 49
-#define CLK_BUS_MSGBOX 50
-#define CLK_BUS_SPINLOCK 51
-#define CLK_BUS_CODEC 52
-#define CLK_BUS_SPDIF 53
-#define CLK_BUS_PIO 54
-#define CLK_BUS_THS 55
-#define CLK_BUS_I2S0 56
-#define CLK_BUS_I2S1 57
-#define CLK_BUS_I2S2 58
-#define CLK_BUS_I2C0 59
-#define CLK_BUS_I2C1 60
-#define CLK_BUS_I2C2 61
-#define CLK_BUS_UART0 62
-#define CLK_BUS_UART1 63
-#define CLK_BUS_UART2 64
-#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
-#define CLK_BUS_EPHY 67
-#define CLK_BUS_DBG 68
-
-#define CLK_THS 69
-#define CLK_NAND 70
-#define CLK_MMC0 71
-#define CLK_MMC0_SAMPLE 72
-#define CLK_MMC0_OUTPUT 73
-#define CLK_MMC1 74
-#define CLK_MMC1_SAMPLE 75
-#define CLK_MMC1_OUTPUT 76
-#define CLK_MMC2 77
-#define CLK_MMC2_SAMPLE 78
-#define CLK_MMC2_OUTPUT 79
-#define CLK_TS 80
-#define CLK_CE 81
-#define CLK_SPI0 82
-#define CLK_SPI1 83
-#define CLK_I2S0 84
-#define CLK_I2S1 85
-#define CLK_I2S2 86
-#define CLK_SPDIF 87
-#define CLK_USB_PHY0 88
-#define CLK_USB_PHY1 89
-#define CLK_USB_PHY2 90
-#define CLK_USB_PHY3 91
-#define CLK_USB_OHCI0 92
-#define CLK_USB_OHCI1 93
-#define CLK_USB_OHCI2 94
-#define CLK_USB_OHCI3 95
-
-#define CLK_DRAM_VE 97
-#define CLK_DRAM_CSI 98
-#define CLK_DRAM_DEINTERLACE 99
-#define CLK_DRAM_TS 100
-#define CLK_DE 101
-#define CLK_TCON0 102
-#define CLK_TVE 103
-#define CLK_DEINTERLACE 104
-#define CLK_CSI_MISC 105
-#define CLK_CSI_SCLK 106
-#define CLK_CSI_MCLK 107
-#define CLK_VE 108
-#define CLK_AC_DIG 109
-#define CLK_AVS 110
-#define CLK_HDMI 111
-#define CLK_HDMI_DDC 112
-
-#define CLK_GPU 114
-
-#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/clock/sunxi-h3-h5-ccu.h b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
new file mode 100644
index 000000000000..4899eacef71d
--- /dev/null
+++ b/include/dt-bindings/clock/sunxi-h3-h5-ccu.h
@@ -0,0 +1,148 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_CLK_SUNXI_H3_H5_H_
+
+#define CLK_CPUX 14
+
+#define CLK_BUS_CE 20
+#define CLK_BUS_DMA 21
+#define CLK_BUS_MMC0 22
+#define CLK_BUS_MMC1 23
+#define CLK_BUS_MMC2 24
+#define CLK_BUS_NAND 25
+#define CLK_BUS_DRAM 26
+#define CLK_BUS_EMAC 27
+#define CLK_BUS_TS 28
+#define CLK_BUS_HSTIMER 29
+#define CLK_BUS_SPI0 30
+#define CLK_BUS_SPI1 31
+#define CLK_BUS_OTG 32
+#define CLK_BUS_EHCI0 33
+#define CLK_BUS_EHCI1 34
+#define CLK_BUS_EHCI2 35
+#define CLK_BUS_EHCI3 36
+#define CLK_BUS_OHCI0 37
+#define CLK_BUS_OHCI1 38
+#define CLK_BUS_OHCI2 39
+#define CLK_BUS_OHCI3 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_TCON0 42
+#define CLK_BUS_TCON1 43
+#define CLK_BUS_DEINTERLACE 44
+#define CLK_BUS_CSI 45
+#define CLK_BUS_TVE 46
+#define CLK_BUS_HDMI 47
+#define CLK_BUS_DE 48
+#define CLK_BUS_GPU 49
+#define CLK_BUS_MSGBOX 50
+#define CLK_BUS_SPINLOCK 51
+#define CLK_BUS_CODEC 52
+#define CLK_BUS_SPDIF 53
+#define CLK_BUS_PIO 54
+#define CLK_BUS_THS 55
+#define CLK_BUS_I2S0 56
+#define CLK_BUS_I2S1 57
+#define CLK_BUS_I2S2 58
+#define CLK_BUS_I2C0 59
+#define CLK_BUS_I2C1 60
+#define CLK_BUS_I2C2 61
+#define CLK_BUS_UART0 62
+#define CLK_BUS_UART1 63
+#define CLK_BUS_UART2 64
+#define CLK_BUS_UART3 65
+#define CLK_BUS_SCR0 66
+#define CLK_BUS_EPHY 67
+#define CLK_BUS_DBG 68
+
+#define CLK_THS 69
+#define CLK_NAND 70
+#define CLK_MMC0 71
+#define CLK_MMC0_SAMPLE 72
+#define CLK_MMC0_OUTPUT 73
+#define CLK_MMC1 74
+#define CLK_MMC1_SAMPLE 75
+#define CLK_MMC1_OUTPUT 76
+#define CLK_MMC2 77
+#define CLK_MMC2_SAMPLE 78
+#define CLK_MMC2_OUTPUT 79
+#define CLK_TS 80
+#define CLK_CE 81
+#define CLK_SPI0 82
+#define CLK_SPI1 83
+#define CLK_I2S0 84
+#define CLK_I2S1 85
+#define CLK_I2S2 86
+#define CLK_SPDIF 87
+#define CLK_USB_PHY0 88
+#define CLK_USB_PHY1 89
+#define CLK_USB_PHY2 90
+#define CLK_USB_PHY3 91
+#define CLK_USB_OHCI0 92
+#define CLK_USB_OHCI1 93
+#define CLK_USB_OHCI2 94
+#define CLK_USB_OHCI3 95
+
+#define CLK_DRAM_VE 97
+#define CLK_DRAM_CSI 98
+#define CLK_DRAM_DEINTERLACE 99
+#define CLK_DRAM_TS 100
+#define CLK_DE 101
+#define CLK_TCON0 102
+#define CLK_TVE 103
+#define CLK_DEINTERLACE 104
+#define CLK_CSI_MISC 105
+#define CLK_CSI_SCLK 106
+#define CLK_CSI_MCLK 107
+#define CLK_VE 108
+#define CLK_AC_DIG 109
+#define CLK_AVS 110
+#define CLK_HDMI 111
+#define CLK_HDMI_DDC 112
+
+#define CLK_GPU 114
+
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
+#endif /* _DT_BINDINGS_CLK_SUNXI_H3_H5_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 100644
index 6b7af80c26ec..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
-#define _DT_BINDINGS_RST_SUN8I_H3_H_
-
-#define RST_USB_PHY0 0
-#define RST_USB_PHY1 1
-#define RST_USB_PHY2 2
-#define RST_USB_PHY3 3
-
-#define RST_MBUS 4
-
-#define RST_BUS_CE 5
-#define RST_BUS_DMA 6
-#define RST_BUS_MMC0 7
-#define RST_BUS_MMC1 8
-#define RST_BUS_MMC2 9
-#define RST_BUS_NAND 10
-#define RST_BUS_DRAM 11
-#define RST_BUS_EMAC 12
-#define RST_BUS_TS 13
-#define RST_BUS_HSTIMER 14
-#define RST_BUS_SPI0 15
-#define RST_BUS_SPI1 16
-#define RST_BUS_OTG 17
-#define RST_BUS_EHCI0 18
-#define RST_BUS_EHCI1 19
-#define RST_BUS_EHCI2 20
-#define RST_BUS_EHCI3 21
-#define RST_BUS_OHCI0 22
-#define RST_BUS_OHCI1 23
-#define RST_BUS_OHCI2 24
-#define RST_BUS_OHCI3 25
-#define RST_BUS_VE 26
-#define RST_BUS_TCON0 27
-#define RST_BUS_TCON1 28
-#define RST_BUS_DEINTERLACE 29
-#define RST_BUS_CSI 30
-#define RST_BUS_TVE 31
-#define RST_BUS_HDMI0 32
-#define RST_BUS_HDMI1 33
-#define RST_BUS_DE 34
-#define RST_BUS_GPU 35
-#define RST_BUS_MSGBOX 36
-#define RST_BUS_SPINLOCK 37
-#define RST_BUS_DBG 38
-#define RST_BUS_EPHY 39
-#define RST_BUS_CODEC 40
-#define RST_BUS_SPDIF 41
-#define RST_BUS_THS 42
-#define RST_BUS_I2S0 43
-#define RST_BUS_I2S1 44
-#define RST_BUS_I2S2 45
-#define RST_BUS_I2C0 46
-#define RST_BUS_I2C1 47
-#define RST_BUS_I2C2 48
-#define RST_BUS_UART0 49
-#define RST_BUS_UART1 50
-#define RST_BUS_UART2 51
-#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
-
-#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
new file mode 120000
index 000000000000..ef38232141e4
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -0,0 +1 @@
+sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sunxi-h3-h5-ccu.h b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
new file mode 100644
index 000000000000..1084c157c062
--- /dev/null
+++ b/include/dt-bindings/reset/sunxi-h3-h5-ccu.h
@@ -0,0 +1,106 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RST_SUNXI_H3_H5_H_
+#define _DT_BINDINGS_RST_SUNXI_H3_H5_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_USB_PHY2 2
+#define RST_USB_PHY3 3
+
+#define RST_MBUS 4
+
+#define RST_BUS_CE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MMC0 7
+#define RST_BUS_MMC1 8
+#define RST_BUS_MMC2 9
+#define RST_BUS_NAND 10
+#define RST_BUS_DRAM 11
+#define RST_BUS_EMAC 12
+#define RST_BUS_TS 13
+#define RST_BUS_HSTIMER 14
+#define RST_BUS_SPI0 15
+#define RST_BUS_SPI1 16
+#define RST_BUS_OTG 17
+#define RST_BUS_EHCI0 18
+#define RST_BUS_EHCI1 19
+#define RST_BUS_EHCI2 20
+#define RST_BUS_EHCI3 21
+#define RST_BUS_OHCI0 22
+#define RST_BUS_OHCI1 23
+#define RST_BUS_OHCI2 24
+#define RST_BUS_OHCI3 25
+#define RST_BUS_VE 26
+#define RST_BUS_TCON0 27
+#define RST_BUS_TCON1 28
+#define RST_BUS_DEINTERLACE 29
+#define RST_BUS_CSI 30
+#define RST_BUS_TVE 31
+#define RST_BUS_HDMI0 32
+#define RST_BUS_HDMI1 33
+#define RST_BUS_DE 34
+#define RST_BUS_GPU 35
+#define RST_BUS_MSGBOX 36
+#define RST_BUS_SPINLOCK 37
+#define RST_BUS_DBG 38
+#define RST_BUS_EPHY 39
+#define RST_BUS_CODEC 40
+#define RST_BUS_SPDIF 41
+#define RST_BUS_THS 42
+#define RST_BUS_I2S0 43
+#define RST_BUS_I2S1 44
+#define RST_BUS_I2S2 45
+#define RST_BUS_I2C0 46
+#define RST_BUS_I2C1 47
+#define RST_BUS_I2C2 48
+#define RST_BUS_UART0 49
+#define RST_BUS_UART1 50
+#define RST_BUS_UART2 51
+#define RST_BUS_UART3 52
+#define RST_BUS_SCR0 53
+
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
+
+#endif /* _DT_BINDINGS_RST_SUNXI_H3_H5_H_ */
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 4/9] arm: dts: sun8i: split Allwinner H3 .dtsi
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-01-26 15:48 ` Icenowy Zheng
-1 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
On the way get rid of skeleton.dtsi, as recommended in that very file.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: also split out mmc, as well as pio and ccu's compatible]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 501 +--------------------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 557 +++++++++++++++++++++++++++++++++++++
2 files changed, 563 insertions(+), 495 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 08fd0860bb6b..49e9b1c580b6 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -40,12 +40,7 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include "sunxi-h3-h5.dtsi"
/ {
interrupt-parent = <&gic>;
@@ -87,71 +82,9 @@
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk@01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller@01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc@01c0f000 {
+ mmc@01c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
clocks = <&ccu CLK_BUS_MMC0>,
<&ccu CLK_MMC0>,
<&ccu CLK_MMC0_OUTPUT>,
@@ -160,17 +93,10 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
- mmc1: mmc@01c10000 {
+ mmc@01c10000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
clocks = <&ccu CLK_BUS_MMC1>,
<&ccu CLK_MMC1>,
<&ccu CLK_MMC1_OUTPUT>,
@@ -179,17 +105,10 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
- mmc2: mmc@01c11000 {
+ mmc@01c11000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
clocks = <&ccu CLK_BUS_MMC2>,
<&ccu CLK_MMC2>,
<&ccu CLK_MMC2_OUTPUT>,
@@ -198,376 +117,14 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb@01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
};
- ohci1: usb@01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb@01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb@01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb@01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb@01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock@01c20000 {
+ clock@01c20000 {
compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
};
- pio: pinctrl@01c20800 {
+ pinctrl@01c20800 {
compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0@0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin@0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1@0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0@0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi@01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi@01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog@01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- pwm: pwm@01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec@01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial@01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial@01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial@01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c@01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c@01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c@01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
gic: interrupt-controller@01c81000 {
@@ -580,51 +137,5 @@
#interrupt-cells = <3>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
-
- rtc: rtc@01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset@01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog@01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir@01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl@01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir@0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
};
};
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
new file mode 100644
index 000000000000..4a57c65e8869
--- /dev/null
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -0,0 +1,557 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ apb0: apb0_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "apb0";
+ };
+
+ apb0_gates: clk@01f01428 {
+ compatible = "allwinner,sun8i-h3-apb0-gates-clk",
+ "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01f01428 0x4>;
+ #clock-cells = <1>;
+ clocks = <&apb0>;
+ clock-indices = <0>, <1>;
+ clock-output-names = "apb0_pio", "apb0_ir";
+ };
+
+ ir_clk: ir_clk@01f01454 {
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01f01454 0x4>;
+ #clock-cells = <0>;
+ clocks = <&osc32k>, <&osc24M>;
+ clock-output-names = "ir";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun8i-h3-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
+ mmc0: mmc@01c0f000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c0f000 0x1000>;
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c10000 0x1000>;
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c11000 0x1000>;
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbphy: phy@01c19400 {
+ compatible = "allwinner,sun8i-h3-usb-phy";
+ reg = <0x01c19400 0x2c>,
+ <0x01c1a800 0x4>,
+ <0x01c1b800 0x4>,
+ <0x01c1c800 0x4>,
+ <0x01c1d800 0x4>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1",
+ "pmu2",
+ "pmu3";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>,
+ <&ccu CLK_USB_PHY3>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy",
+ "usb3_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>,
+ <&ccu RST_USB_PHY3>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset",
+ "usb3_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci1: usb@01c1b000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1b000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@01c1b400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1b400 0x100>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci2: usb@01c1c000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1c000 0x100>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb@01c1c400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1c400 0x100>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci3: usb@01c1d000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1d000 0x100>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci3: usb@01c1d400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1d400 0x100>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ccu: clock@01c20000 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ pio: pinctrl@01c20800 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ i2c0_pins: i2c0 {
+ pins = "PA11", "PA12";
+ function = "i2c0";
+ };
+
+ i2c1_pins: i2c1 {
+ pins = "PA18", "PA19";
+ function = "i2c1";
+ };
+
+ i2c2_pins: i2c2 {
+ pins = "PE12", "PE13";
+ function = "i2c2";
+ };
+
+ mmc0_pins_a: mmc0@0 {
+ pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin@0 {
+ pins = "PF6";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+
+ mmc1_pins_a: mmc1@0 {
+ pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_8bit_pins: mmc2_8bit {
+ pins = "PC5", "PC6", "PC8",
+ "PC9", "PC10", "PC11",
+ "PC12", "PC13", "PC14",
+ "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ spi0_pins: spi0 {
+ pins = "PC0", "PC1", "PC2", "PC3";
+ function = "spi0";
+ };
+
+ spi1_pins: spi1 {
+ pins = "PA15", "PA16", "PA14", "PA13";
+ function = "spi1";
+ };
+
+ uart0_pins_a: uart0@0 {
+ pins = "PA4", "PA5";
+ function = "uart0";
+ };
+
+ uart1_pins: uart1 {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ uart1_rts_cts_pins: uart1_rts_cts {
+ pins = "PG8", "PG9";
+ function = "uart1";
+ };
+
+ uart2_pins: uart2 {
+ pins = "PA0", "PA1";
+ function = "uart2";
+ };
+
+ uart3_pins: uart3 {
+ pins = "PA13", "PA14";
+ function = "uart3";
+ };
+ };
+
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ spi0: spi@01c68000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c68000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ resets = <&ccu RST_BUS_SPI0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@01c69000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c69000 0x1000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 24>, <&dma 24>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ resets = <&ccu RST_BUS_SPI1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ wdt0: watchdog@01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pwm: pwm@01c21400 {
+ compatible = "allwinner,sun8i-h3-pwm";
+ reg = <0x01c21400 0x8>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ codec: codec@01c22c00 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-h3-codec";
+ reg = <0x01c22c00 0x400>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
+ clock-names = "apb", "codec";
+ resets = <&ccu RST_BUS_CODEC>;
+ dmas = <&dma 15>, <&dma 15>;
+ dma-names = "rx", "tx";
+ allwinner,codec-analog-controls = <&codec_analog>;
+ status = "disabled";
+ };
+
+ uart0: serial@01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial@01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial@01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial@01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2c0: i2c@01c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@01c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@01c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ rtc: rtc@01f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apb0_reset: reset@01f014b0 {
+ reg = <0x01f014b0 0x4>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ #reset-cells = <1>;
+ };
+
+ codec_analog: codec-analog@01f015c0 {
+ compatible = "allwinner,sun8i-h3-codec-analog";
+ reg = <0x01f015c0 0x4>;
+ };
+
+ ir: ir@01f02000 {
+ compatible = "allwinner,sun5i-a13-ir";
+ clocks = <&apb0_gates 1>, <&ir_clk>;
+ clock-names = "apb", "ir";
+ resets = <&apb0_reset 1>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x01f02000 0x40>;
+ status = "disabled";
+ };
+
+ r_pio: pinctrl@01f02c00 {
+ compatible = "allwinner,sun8i-h3-r-pinctrl";
+ reg = <0x01f02c00 0x400>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ resets = <&apb0_reset 0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ ir_pins_a: ir@0 {
+ pins = "PL11";
+ function = "s_cir_rx";
+ };
+ };
+ };
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 4/9] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
On the way get rid of skeleton.dtsi, as recommended in that very file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc, as well as pio and ccu's compatible]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 501 +--------------------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 557 +++++++++++++++++++++++++++++++++++++
2 files changed, 563 insertions(+), 495 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 08fd0860bb6b..49e9b1c580b6 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -40,12 +40,7 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include "sunxi-h3-h5.dtsi"
/ {
interrupt-parent = <&gic>;
@@ -87,71 +82,9 @@
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk@01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller@01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc@01c0f000 {
+ mmc@01c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
clocks = <&ccu CLK_BUS_MMC0>,
<&ccu CLK_MMC0>,
<&ccu CLK_MMC0_OUTPUT>,
@@ -160,17 +93,10 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
- mmc1: mmc@01c10000 {
+ mmc@01c10000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
clocks = <&ccu CLK_BUS_MMC1>,
<&ccu CLK_MMC1>,
<&ccu CLK_MMC1_OUTPUT>,
@@ -179,17 +105,10 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
- mmc2: mmc@01c11000 {
+ mmc@01c11000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
clocks = <&ccu CLK_BUS_MMC2>,
<&ccu CLK_MMC2>,
<&ccu CLK_MMC2_OUTPUT>,
@@ -198,376 +117,14 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb@01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
};
- ohci1: usb@01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb@01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb@01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb@01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb@01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock@01c20000 {
+ clock@01c20000 {
compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
};
- pio: pinctrl@01c20800 {
+ pinctrl@01c20800 {
compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0@0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin@0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1@0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0@0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi@01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi@01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog@01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- pwm: pwm@01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec@01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial@01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial@01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial@01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c@01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c@01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c@01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
gic: interrupt-controller@01c81000 {
@@ -580,51 +137,5 @@
#interrupt-cells = <3>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
-
- rtc: rtc@01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset@01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog@01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir@01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl@01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir@0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
};
};
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
new file mode 100644
index 000000000000..4a57c65e8869
--- /dev/null
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -0,0 +1,557 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ apb0: apb0_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "apb0";
+ };
+
+ apb0_gates: clk@01f01428 {
+ compatible = "allwinner,sun8i-h3-apb0-gates-clk",
+ "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01f01428 0x4>;
+ #clock-cells = <1>;
+ clocks = <&apb0>;
+ clock-indices = <0>, <1>;
+ clock-output-names = "apb0_pio", "apb0_ir";
+ };
+
+ ir_clk: ir_clk@01f01454 {
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01f01454 0x4>;
+ #clock-cells = <0>;
+ clocks = <&osc32k>, <&osc24M>;
+ clock-output-names = "ir";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun8i-h3-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
+ mmc0: mmc@01c0f000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c0f000 0x1000>;
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c10000 0x1000>;
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c11000 0x1000>;
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbphy: phy@01c19400 {
+ compatible = "allwinner,sun8i-h3-usb-phy";
+ reg = <0x01c19400 0x2c>,
+ <0x01c1a800 0x4>,
+ <0x01c1b800 0x4>,
+ <0x01c1c800 0x4>,
+ <0x01c1d800 0x4>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1",
+ "pmu2",
+ "pmu3";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>,
+ <&ccu CLK_USB_PHY3>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy",
+ "usb3_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>,
+ <&ccu RST_USB_PHY3>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset",
+ "usb3_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci1: usb@01c1b000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1b000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@01c1b400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1b400 0x100>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci2: usb@01c1c000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1c000 0x100>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb@01c1c400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1c400 0x100>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci3: usb@01c1d000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1d000 0x100>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci3: usb@01c1d400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1d400 0x100>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ccu: clock@01c20000 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ pio: pinctrl@01c20800 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ i2c0_pins: i2c0 {
+ pins = "PA11", "PA12";
+ function = "i2c0";
+ };
+
+ i2c1_pins: i2c1 {
+ pins = "PA18", "PA19";
+ function = "i2c1";
+ };
+
+ i2c2_pins: i2c2 {
+ pins = "PE12", "PE13";
+ function = "i2c2";
+ };
+
+ mmc0_pins_a: mmc0@0 {
+ pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin@0 {
+ pins = "PF6";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+
+ mmc1_pins_a: mmc1@0 {
+ pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_8bit_pins: mmc2_8bit {
+ pins = "PC5", "PC6", "PC8",
+ "PC9", "PC10", "PC11",
+ "PC12", "PC13", "PC14",
+ "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ spi0_pins: spi0 {
+ pins = "PC0", "PC1", "PC2", "PC3";
+ function = "spi0";
+ };
+
+ spi1_pins: spi1 {
+ pins = "PA15", "PA16", "PA14", "PA13";
+ function = "spi1";
+ };
+
+ uart0_pins_a: uart0@0 {
+ pins = "PA4", "PA5";
+ function = "uart0";
+ };
+
+ uart1_pins: uart1 {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ uart1_rts_cts_pins: uart1_rts_cts {
+ pins = "PG8", "PG9";
+ function = "uart1";
+ };
+
+ uart2_pins: uart2 {
+ pins = "PA0", "PA1";
+ function = "uart2";
+ };
+
+ uart3_pins: uart3 {
+ pins = "PA13", "PA14";
+ function = "uart3";
+ };
+ };
+
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ spi0: spi@01c68000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c68000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ resets = <&ccu RST_BUS_SPI0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@01c69000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c69000 0x1000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 24>, <&dma 24>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ resets = <&ccu RST_BUS_SPI1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ wdt0: watchdog@01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pwm: pwm@01c21400 {
+ compatible = "allwinner,sun8i-h3-pwm";
+ reg = <0x01c21400 0x8>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ codec: codec@01c22c00 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-h3-codec";
+ reg = <0x01c22c00 0x400>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
+ clock-names = "apb", "codec";
+ resets = <&ccu RST_BUS_CODEC>;
+ dmas = <&dma 15>, <&dma 15>;
+ dma-names = "rx", "tx";
+ allwinner,codec-analog-controls = <&codec_analog>;
+ status = "disabled";
+ };
+
+ uart0: serial@01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial@01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial@01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial@01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2c0: i2c@01c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@01c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@01c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ rtc: rtc@01f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apb0_reset: reset@01f014b0 {
+ reg = <0x01f014b0 0x4>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ #reset-cells = <1>;
+ };
+
+ codec_analog: codec-analog@01f015c0 {
+ compatible = "allwinner,sun8i-h3-codec-analog";
+ reg = <0x01f015c0 0x4>;
+ };
+
+ ir: ir@01f02000 {
+ compatible = "allwinner,sun5i-a13-ir";
+ clocks = <&apb0_gates 1>, <&ir_clk>;
+ clock-names = "apb", "ir";
+ resets = <&apb0_reset 1>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x01f02000 0x40>;
+ status = "disabled";
+ };
+
+ r_pio: pinctrl@01f02c00 {
+ compatible = "allwinner,sun8i-h3-r-pinctrl";
+ reg = <0x01f02c00 0x400>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ resets = <&apb0_reset 0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ ir_pins_a: ir@0 {
+ pins = "PL11";
+ function = "s_cir_rx";
+ };
+ };
+ };
+};
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 4/9] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
On the way get rid of skeleton.dtsi, as recommended in that very file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc, as well as pio and ccu's compatible]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 501 +--------------------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 557 +++++++++++++++++++++++++++++++++++++
2 files changed, 563 insertions(+), 495 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 08fd0860bb6b..49e9b1c580b6 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -40,12 +40,7 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include "sunxi-h3-h5.dtsi"
/ {
interrupt-parent = <&gic>;
@@ -87,71 +82,9 @@
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk at 01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk at 01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller at 01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc at 01c0f000 {
+ mmc at 01c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
clocks = <&ccu CLK_BUS_MMC0>,
<&ccu CLK_MMC0>,
<&ccu CLK_MMC0_OUTPUT>,
@@ -160,17 +93,10 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
- mmc1: mmc at 01c10000 {
+ mmc at 01c10000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
clocks = <&ccu CLK_BUS_MMC1>,
<&ccu CLK_MMC1>,
<&ccu CLK_MMC1_OUTPUT>,
@@ -179,17 +105,10 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
- mmc2: mmc at 01c11000 {
+ mmc at 01c11000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
clocks = <&ccu CLK_BUS_MMC2>,
<&ccu CLK_MMC2>,
<&ccu CLK_MMC2_OUTPUT>,
@@ -198,376 +117,14 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy at 01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb at 01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
};
- ohci1: usb at 01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb at 01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb at 01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb at 01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb at 01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock at 01c20000 {
+ clock at 01c20000 {
compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
};
- pio: pinctrl at 01c20800 {
+ pinctrl at 01c20800 {
compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0 at 0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin at 0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1 at 0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0 at 0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer at 01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi at 01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi at 01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog at 01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- pwm: pwm at 01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec at 01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial at 01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial at 01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial at 01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial at 01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c at 01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c at 01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c at 01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
gic: interrupt-controller at 01c81000 {
@@ -580,51 +137,5 @@
#interrupt-cells = <3>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
-
- rtc: rtc at 01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset at 01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog at 01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir at 01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl at 01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir at 0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
};
};
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
new file mode 100644
index 000000000000..4a57c65e8869
--- /dev/null
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -0,0 +1,557 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ apb0: apb0_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "apb0";
+ };
+
+ apb0_gates: clk at 01f01428 {
+ compatible = "allwinner,sun8i-h3-apb0-gates-clk",
+ "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01f01428 0x4>;
+ #clock-cells = <1>;
+ clocks = <&apb0>;
+ clock-indices = <0>, <1>;
+ clock-output-names = "apb0_pio", "apb0_ir";
+ };
+
+ ir_clk: ir_clk at 01f01454 {
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01f01454 0x4>;
+ #clock-cells = <0>;
+ clocks = <&osc32k>, <&osc24M>;
+ clock-output-names = "ir";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dma: dma-controller at 01c02000 {
+ compatible = "allwinner,sun8i-h3-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
+ mmc0: mmc at 01c0f000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c0f000 0x1000>;
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc at 01c10000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c10000 0x1000>;
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc at 01c11000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c11000 0x1000>;
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbphy: phy at 01c19400 {
+ compatible = "allwinner,sun8i-h3-usb-phy";
+ reg = <0x01c19400 0x2c>,
+ <0x01c1a800 0x4>,
+ <0x01c1b800 0x4>,
+ <0x01c1c800 0x4>,
+ <0x01c1d800 0x4>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1",
+ "pmu2",
+ "pmu3";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>,
+ <&ccu CLK_USB_PHY3>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy",
+ "usb3_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>,
+ <&ccu RST_USB_PHY3>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset",
+ "usb3_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci1: usb at 01c1b000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1b000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb at 01c1b400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1b400 0x100>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci2: usb at 01c1c000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1c000 0x100>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb at 01c1c400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1c400 0x100>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci3: usb at 01c1d000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1d000 0x100>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci3: usb at 01c1d400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1d400 0x100>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ccu: clock at 01c20000 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ pio: pinctrl at 01c20800 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ i2c0_pins: i2c0 {
+ pins = "PA11", "PA12";
+ function = "i2c0";
+ };
+
+ i2c1_pins: i2c1 {
+ pins = "PA18", "PA19";
+ function = "i2c1";
+ };
+
+ i2c2_pins: i2c2 {
+ pins = "PE12", "PE13";
+ function = "i2c2";
+ };
+
+ mmc0_pins_a: mmc0 at 0 {
+ pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin at 0 {
+ pins = "PF6";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+
+ mmc1_pins_a: mmc1 at 0 {
+ pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_8bit_pins: mmc2_8bit {
+ pins = "PC5", "PC6", "PC8",
+ "PC9", "PC10", "PC11",
+ "PC12", "PC13", "PC14",
+ "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ spi0_pins: spi0 {
+ pins = "PC0", "PC1", "PC2", "PC3";
+ function = "spi0";
+ };
+
+ spi1_pins: spi1 {
+ pins = "PA15", "PA16", "PA14", "PA13";
+ function = "spi1";
+ };
+
+ uart0_pins_a: uart0 at 0 {
+ pins = "PA4", "PA5";
+ function = "uart0";
+ };
+
+ uart1_pins: uart1 {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ uart1_rts_cts_pins: uart1_rts_cts {
+ pins = "PG8", "PG9";
+ function = "uart1";
+ };
+
+ uart2_pins: uart2 {
+ pins = "PA0", "PA1";
+ function = "uart2";
+ };
+
+ uart3_pins: uart3 {
+ pins = "PA13", "PA14";
+ function = "uart3";
+ };
+ };
+
+ timer at 01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ spi0: spi at 01c68000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c68000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ resets = <&ccu RST_BUS_SPI0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi at 01c69000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c69000 0x1000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 24>, <&dma 24>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ resets = <&ccu RST_BUS_SPI1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ wdt0: watchdog at 01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pwm: pwm at 01c21400 {
+ compatible = "allwinner,sun8i-h3-pwm";
+ reg = <0x01c21400 0x8>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ codec: codec at 01c22c00 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-h3-codec";
+ reg = <0x01c22c00 0x400>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
+ clock-names = "apb", "codec";
+ resets = <&ccu RST_BUS_CODEC>;
+ dmas = <&dma 15>, <&dma 15>;
+ dma-names = "rx", "tx";
+ allwinner,codec-analog-controls = <&codec_analog>;
+ status = "disabled";
+ };
+
+ uart0: serial at 01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial at 01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial at 01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial at 01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2c0: i2c at 01c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c at 01c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c at 01c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ rtc: rtc at 01f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apb0_reset: reset at 01f014b0 {
+ reg = <0x01f014b0 0x4>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ #reset-cells = <1>;
+ };
+
+ codec_analog: codec-analog at 01f015c0 {
+ compatible = "allwinner,sun8i-h3-codec-analog";
+ reg = <0x01f015c0 0x4>;
+ };
+
+ ir: ir at 01f02000 {
+ compatible = "allwinner,sun5i-a13-ir";
+ clocks = <&apb0_gates 1>, <&ir_clk>;
+ clock-names = "apb", "ir";
+ resets = <&apb0_reset 1>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x01f02000 0x40>;
+ status = "disabled";
+ };
+
+ r_pio: pinctrl at 01f02c00 {
+ compatible = "allwinner,sun8i-h3-r-pinctrl";
+ reg = <0x01f02c00 0x400>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ resets = <&apb0_reset 0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ ir_pins_a: ir at 0 {
+ pins = "PL11";
+ function = "s_cir_rx";
+ };
+ };
+ };
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 5/9] clk: sunxi-ng: remove transitional headers for dt-bindings
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-01-26 15:48 ` Icenowy Zheng
-1 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
As we have already changed the DTSI file, the trnasitional dt-bindings
header sun8i-h3-ccu.h will not be needed any more.
Remove them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch.
To maintain the bisectbility on the kernel source tree, PATCH 3/7 imports
two header symlinks, to satisfy sun8i-h3.dtsi.
As sun8i-h3.dtsi is changed now, the trasitional header files are now not
needed.
include/dt-bindings/clock/sun8i-h3-ccu.h | 1 -
include/dt-bindings/reset/sun8i-h3-ccu.h | 1 -
2 files changed, 2 deletions(-)
delete mode 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
delete mode 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 5/9] clk: sunxi-ng: remove transitional headers for dt-bindings
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
As we have already changed the DTSI file, the trnasitional dt-bindings
header sun8i-h3-ccu.h will not be needed any more.
Remove them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch.
To maintain the bisectbility on the kernel source tree, PATCH 3/7 imports
two header symlinks, to satisfy sun8i-h3.dtsi.
As sun8i-h3.dtsi is changed now, the trasitional header files are now not
needed.
include/dt-bindings/clock/sun8i-h3-ccu.h | 1 -
include/dt-bindings/reset/sun8i-h3-ccu.h | 1 -
2 files changed, 2 deletions(-)
delete mode 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
delete mode 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 5/9] clk: sunxi-ng: remove transitional headers for dt-bindings
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
As we have already changed the DTSI file, the trnasitional dt-bindings
header sun8i-h3-ccu.h will not be needed any more.
Remove them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch.
To maintain the bisectbility on the kernel source tree, PATCH 3/7 imports
two header symlinks, to satisfy sun8i-h3.dtsi.
As sun8i-h3.dtsi is changed now, the trasitional header files are now not
needed.
include/dt-bindings/clock/sun8i-h3-ccu.h | 1 -
include/dt-bindings/reset/sun8i-h3-ccu.h | 1 -
2 files changed, 2 deletions(-)
delete mode 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
delete mode 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
deleted file mode 120000
index ef38232141e4..000000000000
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ /dev/null
@@ -1 +0,0 @@
-sunxi-h3-h5-ccu.h
\ No newline at end of file
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 6/9] arm64: dts: allwinner: add Allwinner H5 .dtsi
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-01-26 15:48 ` Icenowy Zheng
-1 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: remove H5 mmc compatible (seems equal to A64), add H5 pinctrl
compatible, and changes for my h3-h5 dtsi refactor, commit message
change to met new arm64 naming scheme, drop H3 pinctrl compatible
because of interrupt bank change]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
in fact different.
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 140 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 141 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..7a31302be73c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,140 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ mmc@01c0f000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ };
+
+ mmc@01c10000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ };
+
+ mmc@01c11000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ };
+
+ clock@01c20000 {
+ compatible = "allwinner,sun50i-h5-ccu",
+ "allwinner,sun8i-h3-ccu";
+ };
+
+ pinctrl@01c20800 {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+ };
+
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 6/9] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: remove H5 mmc compatible (seems equal to A64), add H5 pinctrl
compatible, and changes for my h3-h5 dtsi refactor, commit message
change to met new arm64 naming scheme, drop H3 pinctrl compatible
because of interrupt bank change]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
in fact different.
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 140 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 141 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..7a31302be73c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,140 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ mmc@01c0f000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ };
+
+ mmc@01c10000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ };
+
+ mmc@01c11000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ };
+
+ clock@01c20000 {
+ compatible = "allwinner,sun50i-h5-ccu",
+ "allwinner,sun8i-h3-ccu";
+ };
+
+ pinctrl@01c20800 {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+ };
+
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 6/9] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: remove H5 mmc compatible (seems equal to A64), add H5 pinctrl
compatible, and changes for my h3-h5 dtsi refactor, commit message
change to met new arm64 naming scheme, drop H3 pinctrl compatible
because of interrupt bank change]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
in fact different.
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 140 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 141 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..7a31302be73c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,140 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ mmc at 01c0f000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ };
+
+ mmc at 01c10000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ };
+
+ mmc at 01c11000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ };
+
+ clock at 01c20000 {
+ compatible = "allwinner,sun50i-h5-ccu",
+ "allwinner,sun8i-h3-ccu";
+ };
+
+ pinctrl at 01c20800 {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+ };
+
+ gic: interrupt-controller at 1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-01-26 15:48 ` Icenowy Zheng
-1 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
driver should be allowed to be built for ARM64, in order to make it work on H5.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
New patch in v2, as H3 codec support is added between v1 and v2.
drivers/dma/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index 0d6a96ee9fc7..d01d59812cf3 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -157,7 +157,7 @@ config DMA_SUN4I
config DMA_SUN6I
tristate "Allwinner A31 SoCs DMA support"
- depends on MACH_SUN6I || MACH_SUN8I || COMPILE_TEST
+ depends on MACH_SUN6I || MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
depends on RESET_CONTROLLER
select DMA_ENGINE
select DMA_VIRTUAL_CHANNELS
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
driver should be allowed to be built for ARM64, in order to make it work on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch in v2, as H3 codec support is added between v1 and v2.
drivers/dma/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index 0d6a96ee9fc7..d01d59812cf3 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -157,7 +157,7 @@ config DMA_SUN4I
config DMA_SUN6I
tristate "Allwinner A31 SoCs DMA support"
- depends on MACH_SUN6I || MACH_SUN8I || COMPILE_TEST
+ depends on MACH_SUN6I || MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
depends on RESET_CONTROLLER
select DMA_ENGINE
select DMA_VIRTUAL_CHANNELS
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
driver should be allowed to be built for ARM64, in order to make it work on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch in v2, as H3 codec support is added between v1 and v2.
drivers/dma/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index 0d6a96ee9fc7..d01d59812cf3 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -157,7 +157,7 @@ config DMA_SUN4I
config DMA_SUN6I
tristate "Allwinner A31 SoCs DMA support"
- depends on MACH_SUN6I || MACH_SUN8I || COMPILE_TEST
+ depends on MACH_SUN6I || MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
depends on RESET_CONTROLLER
select DMA_ENGINE
select DMA_VIRTUAL_CHANNELS
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-01-26 15:48 ` Icenowy Zheng
-1 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
same digital part) as H3, enable the driver to be built on ARM64
Allwinner platform, so that it can be used on H5.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
New patch in v2.
sound/soc/sunxi/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/sound/soc/sunxi/Kconfig b/sound/soc/sunxi/Kconfig
index 6c344e16aca4..49b71719c9b9 100644
--- a/sound/soc/sunxi/Kconfig
+++ b/sound/soc/sunxi/Kconfig
@@ -11,7 +11,7 @@ config SND_SUN4I_CODEC
config SND_SUN8I_CODEC_ANALOG
tristate "Allwinner sun8i Codec Analog Controls Support"
- depends on MACH_SUN8I || COMPILE_TEST
+ depends on MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
select REGMAP
help
Say Y or M if you want to add support for the analog controls for
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
same digital part) as H3, enable the driver to be built on ARM64
Allwinner platform, so that it can be used on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch in v2.
sound/soc/sunxi/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/sound/soc/sunxi/Kconfig b/sound/soc/sunxi/Kconfig
index 6c344e16aca4..49b71719c9b9 100644
--- a/sound/soc/sunxi/Kconfig
+++ b/sound/soc/sunxi/Kconfig
@@ -11,7 +11,7 @@ config SND_SUN4I_CODEC
config SND_SUN8I_CODEC_ANALOG
tristate "Allwinner sun8i Codec Analog Controls Support"
- depends on MACH_SUN8I || COMPILE_TEST
+ depends on MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
select REGMAP
help
Say Y or M if you want to add support for the analog controls for
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
same digital part) as H3, enable the driver to be built on ARM64
Allwinner platform, so that it can be used on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch in v2.
sound/soc/sunxi/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/sound/soc/sunxi/Kconfig b/sound/soc/sunxi/Kconfig
index 6c344e16aca4..49b71719c9b9 100644
--- a/sound/soc/sunxi/Kconfig
+++ b/sound/soc/sunxi/Kconfig
@@ -11,7 +11,7 @@ config SND_SUN4I_CODEC
config SND_SUN8I_CODEC_ANALOG
tristate "Allwinner sun8i Codec Analog Controls Support"
- depends on MACH_SUN8I || COMPILE_TEST
+ depends on MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
select REGMAP
help
Say Y or M if you want to add support for the analog controls for
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 9/9] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-01-26 15:48 ` Icenowy Zheng
-1 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 +++++++++++++++++++++
2 files changed, 165 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 1e29a5ae8282..b26bb46b934c 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,4 +1,5 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..79784cba806c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 9/9] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara
Cc: devicetree, alsa-devel, linux-kernel, linux-gpio, linux-sunxi,
Icenowy Zheng, dmaengine, linux-clk, linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 +++++++++++++++++++++
2 files changed, 165 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 1e29a5ae8282..b26bb46b934c 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,4 +1,5 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..79784cba806c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 69+ messages in thread
* [PATCH v2 9/9] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-01-26 15:48 ` Icenowy Zheng
0 siblings, 0 replies; 69+ messages in thread
From: Icenowy Zheng @ 2017-01-26 15:48 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 164 +++++++++++++++++++++
2 files changed, 165 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 1e29a5ae8282..b26bb46b934c 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,4 +1,5 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..79784cba806c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* Re: [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
2017-01-26 15:48 ` Icenowy Zheng
(?)
(?)
@ 2017-01-27 15:51 ` Maxime Ripard
-1 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:51 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 613 bytes --]
On Thu, Jan 26, 2017 at 11:48:51PM +0800, Icenowy Zheng wrote:
> Based on the Allwinner H5 datasheet and the pinctrl driver of the
> backward-compatible H3 this introduces the pin multiplex assignments for
> the H5 SoC.
>
> H5 introduced some more pin functions (e.g. three more groups of TS
> pins, and one more groups of SIM pins) than H3.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
Acked-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
@ 2017-01-27 15:51 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:51 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-gpio, dmaengine,
alsa-devel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 581 bytes --]
On Thu, Jan 26, 2017 at 11:48:51PM +0800, Icenowy Zheng wrote:
> Based on the Allwinner H5 datasheet and the pinctrl driver of the
> backward-compatible H3 this introduces the pin multiplex assignments for
> the H5 SoC.
>
> H5 introduced some more pin functions (e.g. three more groups of TS
> pins, and one more groups of SIM pins) than H3.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
@ 2017-01-27 15:51 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:51 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, alsa-devel, Vinod Koul, Andre Przywara,
Linus Walleij, linux-sunxi, linux-kernel, Jaroslav Kysela,
linux-gpio, Chen-Yu Tsai, Mark Brown, dmaengine, linux-clk,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 581 bytes --]
On Thu, Jan 26, 2017 at 11:48:51PM +0800, Icenowy Zheng wrote:
> Based on the Allwinner H5 datasheet and the pinctrl driver of the
> backward-compatible H3 this introduces the pin multiplex assignments for
> the H5 SoC.
>
> H5 introduced some more pin functions (e.g. three more groups of TS
> pins, and one more groups of SIM pins) than H3.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
@ 2017-01-27 15:51 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:51 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 26, 2017 at 11:48:51PM +0800, Icenowy Zheng wrote:
> Based on the Allwinner H5 datasheet and the pinctrl driver of the
> backward-compatible H3 this introduces the pin multiplex assignments for
> the H5 SoC.
>
> H5 introduced some more pin functions (e.g. three more groups of TS
> pins, and one more groups of SIM pins) than H3.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170127/3ef8ed53/attachment.sig>
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 3/9] clk: sunxi-ng: add support for Allwinner H5 SoC
2017-01-26 15:48 ` Icenowy Zheng
(?)
(?)
@ 2017-01-27 15:53 ` Maxime Ripard
-1 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:53 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 1769 bytes --]
On Thu, Jan 26, 2017 at 11:48:53PM +0800, Icenowy Zheng wrote:
> Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
> clocks removed (for new MMC controller) and a new bus gate/reset
> imported.
>
> Add support for it.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
> ---
> A giant rewrite since v1.
> It now do not use a dedicated driver for H5, but altered the CCU driver
> of H3 to support H5.
>
> .../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
> drivers/clk/sunxi-ng/Kconfig | 6 +-
> drivers/clk/sunxi-ng/Makefile | 2 +-
> .../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++++++++++++++---
> .../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
> include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +----------------
> include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 148 +++++++++++++++++
> include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +-----------
> include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 106 ++++++++++++
> 9 files changed, 431 insertions(+), 276 deletions(-)
> rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
> rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
> mode change 100644 => 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
> create mode 100644 include/dt-bindings/clock/sunxi-h3-h5-ccu.h
> mode change 100644 => 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
> create mode 100644 include/dt-bindings/reset/sunxi-h3-h5-ccu.h
Please do that in two patches. One to rename the existing driver, one
to support the H5.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 3/9] clk: sunxi-ng: add support for Allwinner H5 SoC
@ 2017-01-27 15:53 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:53 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-gpio, dmaengine,
alsa-devel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 1790 bytes --]
On Thu, Jan 26, 2017 at 11:48:53PM +0800, Icenowy Zheng wrote:
> Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
> clocks removed (for new MMC controller) and a new bus gate/reset
> imported.
>
> Add support for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> A giant rewrite since v1.
> It now do not use a dedicated driver for H5, but altered the CCU driver
> of H3 to support H5.
>
> .../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
> drivers/clk/sunxi-ng/Kconfig | 6 +-
> drivers/clk/sunxi-ng/Makefile | 2 +-
> .../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++++++++++++++---
> .../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
> include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +----------------
> include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 148 +++++++++++++++++
> include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +-----------
> include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 106 ++++++++++++
> 9 files changed, 431 insertions(+), 276 deletions(-)
> rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
> rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
> mode change 100644 => 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
> create mode 100644 include/dt-bindings/clock/sunxi-h3-h5-ccu.h
> mode change 100644 => 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
> create mode 100644 include/dt-bindings/reset/sunxi-h3-h5-ccu.h
Please do that in two patches. One to rename the existing driver, one
to support the H5.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 3/9] clk: sunxi-ng: add support for Allwinner H5 SoC
@ 2017-01-27 15:53 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:53 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, alsa-devel, Vinod Koul, Andre Przywara,
Linus Walleij, linux-sunxi, linux-kernel, Jaroslav Kysela,
linux-gpio, Chen-Yu Tsai, Mark Brown, dmaengine, linux-clk,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 1790 bytes --]
On Thu, Jan 26, 2017 at 11:48:53PM +0800, Icenowy Zheng wrote:
> Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
> clocks removed (for new MMC controller) and a new bus gate/reset
> imported.
>
> Add support for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> A giant rewrite since v1.
> It now do not use a dedicated driver for H5, but altered the CCU driver
> of H3 to support H5.
>
> .../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
> drivers/clk/sunxi-ng/Kconfig | 6 +-
> drivers/clk/sunxi-ng/Makefile | 2 +-
> .../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++++++++++++++---
> .../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
> include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +----------------
> include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 148 +++++++++++++++++
> include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +-----------
> include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 106 ++++++++++++
> 9 files changed, 431 insertions(+), 276 deletions(-)
> rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
> rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
> mode change 100644 => 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
> create mode 100644 include/dt-bindings/clock/sunxi-h3-h5-ccu.h
> mode change 100644 => 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
> create mode 100644 include/dt-bindings/reset/sunxi-h3-h5-ccu.h
Please do that in two patches. One to rename the existing driver, one
to support the H5.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 3/9] clk: sunxi-ng: add support for Allwinner H5 SoC
@ 2017-01-27 15:53 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:53 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 26, 2017 at 11:48:53PM +0800, Icenowy Zheng wrote:
> Allwinner H5 is a SoC that features a CCU like H3, but with MMC phase
> clocks removed (for new MMC controller) and a new bus gate/reset
> imported.
>
> Add support for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> A giant rewrite since v1.
> It now do not use a dedicated driver for H5, but altered the CCU driver
> of H3 to support H5.
>
> .../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
> drivers/clk/sunxi-ng/Kconfig | 6 +-
> drivers/clk/sunxi-ng/Makefile | 2 +-
> .../sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} | 179 ++++++++++++++++++---
> .../sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} | 15 +-
> include/dt-bindings/clock/sun8i-h3-ccu.h | 146 +----------------
> include/dt-bindings/clock/sunxi-h3-h5-ccu.h | 148 +++++++++++++++++
> include/dt-bindings/reset/sun8i-h3-ccu.h | 104 +-----------
> include/dt-bindings/reset/sunxi-h3-h5-ccu.h | 106 ++++++++++++
> 9 files changed, 431 insertions(+), 276 deletions(-)
> rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.c => ccu-sunxi-h3-h5.c} (80%)
> rename drivers/clk/sunxi-ng/{ccu-sun8i-h3.h => ccu-sunxi-h3-h5.h} (82%)
> mode change 100644 => 120000 include/dt-bindings/clock/sun8i-h3-ccu.h
> create mode 100644 include/dt-bindings/clock/sunxi-h3-h5-ccu.h
> mode change 100644 => 120000 include/dt-bindings/reset/sun8i-h3-ccu.h
> create mode 100644 include/dt-bindings/reset/sunxi-h3-h5-ccu.h
Please do that in two patches. One to rename the existing driver, one
to support the H5.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170127/342fb7e9/attachment.sig>
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 4/9] arm: dts: sun8i: split Allwinner H3 .dtsi
2017-01-26 15:48 ` Icenowy Zheng
(?)
(?)
@ 2017-01-27 15:55 ` Maxime Ripard
-1 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:55 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 347 bytes --]
On Thu, Jan 26, 2017 at 11:48:54PM +0800, Icenowy Zheng wrote:
> - mmc0: mmc@01c0f000 {
> + mmc@01c0f000 {
There's no point in removing the labels, and you can even use the
label-based syntax to reference them, instead of using the path.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 4/9] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-01-27 15:55 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:55 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-gpio, dmaengine,
alsa-devel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 361 bytes --]
On Thu, Jan 26, 2017 at 11:48:54PM +0800, Icenowy Zheng wrote:
> - mmc0: mmc@01c0f000 {
> + mmc@01c0f000 {
There's no point in removing the labels, and you can even use the
label-based syntax to reference them, instead of using the path.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 4/9] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-01-27 15:55 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:55 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, alsa-devel, Vinod Koul, Andre Przywara,
Linus Walleij, linux-sunxi, linux-kernel, Jaroslav Kysela,
linux-gpio, Chen-Yu Tsai, Mark Brown, dmaengine, linux-clk,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 361 bytes --]
On Thu, Jan 26, 2017 at 11:48:54PM +0800, Icenowy Zheng wrote:
> - mmc0: mmc@01c0f000 {
> + mmc@01c0f000 {
There's no point in removing the labels, and you can even use the
label-based syntax to reference them, instead of using the path.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 4/9] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-01-27 15:55 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:55 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 26, 2017 at 11:48:54PM +0800, Icenowy Zheng wrote:
> - mmc0: mmc at 01c0f000 {
> + mmc at 01c0f000 {
There's no point in removing the labels, and you can even use the
label-based syntax to reference them, instead of using the path.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170127/161b3269/attachment.sig>
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 6/9] arm64: dts: allwinner: add Allwinner H5 .dtsi
2017-01-26 15:48 ` Icenowy Zheng
(?)
(?)
@ 2017-01-27 15:58 ` Maxime Ripard
-1 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:58 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 1204 bytes --]
On Thu, Jan 26, 2017 at 11:48:56PM +0800, Icenowy Zheng wrote:
> + mmc@01c0f000 {
Please use a label based syntax here too.
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
The compatibility with the A13 has never been true, and the compatible
should be "allwinner,sun50i-h5-mmc", "allwinner,sun50i-a64-mmc".
> + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + mmc@01c10000 {
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
> + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + mmc@01c11000 {
> + compatible = "allwinner,sun50i-a64-mmc",
And this is very likely to use the emmc compatible.
> + "allwinner,sun5i-a13-mmc";
> + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + clock@01c20000 {
> + compatible = "allwinner,sun50i-h5-ccu",
> + "allwinner,sun8i-h3-ccu";
> + };
If it doesn't have the same clocks, it's not compatible with the H3.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 6/9] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-01-27 15:58 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:58 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-gpio, dmaengine,
alsa-devel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 1250 bytes --]
On Thu, Jan 26, 2017 at 11:48:56PM +0800, Icenowy Zheng wrote:
> + mmc@01c0f000 {
Please use a label based syntax here too.
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
The compatibility with the A13 has never been true, and the compatible
should be "allwinner,sun50i-h5-mmc", "allwinner,sun50i-a64-mmc".
> + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + mmc@01c10000 {
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
> + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + mmc@01c11000 {
> + compatible = "allwinner,sun50i-a64-mmc",
And this is very likely to use the emmc compatible.
> + "allwinner,sun5i-a13-mmc";
> + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + clock@01c20000 {
> + compatible = "allwinner,sun50i-h5-ccu",
> + "allwinner,sun8i-h3-ccu";
> + };
If it doesn't have the same clocks, it's not compatible with the H3.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 6/9] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-01-27 15:58 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:58 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, alsa-devel, Vinod Koul, Andre Przywara,
Linus Walleij, linux-sunxi, linux-kernel, Jaroslav Kysela,
linux-gpio, Chen-Yu Tsai, Mark Brown, dmaengine, linux-clk,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 1250 bytes --]
On Thu, Jan 26, 2017 at 11:48:56PM +0800, Icenowy Zheng wrote:
> + mmc@01c0f000 {
Please use a label based syntax here too.
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
The compatibility with the A13 has never been true, and the compatible
should be "allwinner,sun50i-h5-mmc", "allwinner,sun50i-a64-mmc".
> + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + mmc@01c10000 {
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
> + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + mmc@01c11000 {
> + compatible = "allwinner,sun50i-a64-mmc",
And this is very likely to use the emmc compatible.
> + "allwinner,sun5i-a13-mmc";
> + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + clock@01c20000 {
> + compatible = "allwinner,sun50i-h5-ccu",
> + "allwinner,sun8i-h3-ccu";
> + };
If it doesn't have the same clocks, it's not compatible with the H3.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 6/9] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-01-27 15:58 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:58 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 26, 2017 at 11:48:56PM +0800, Icenowy Zheng wrote:
> + mmc at 01c0f000 {
Please use a label based syntax here too.
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
The compatibility with the A13 has never been true, and the compatible
should be "allwinner,sun50i-h5-mmc", "allwinner,sun50i-a64-mmc".
> + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + mmc at 01c10000 {
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
> + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + mmc at 01c11000 {
> + compatible = "allwinner,sun50i-a64-mmc",
And this is very likely to use the emmc compatible.
> + "allwinner,sun5i-a13-mmc";
> + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
> + clock-names = "ahb", "mmc";
> + };
> +
> + clock at 01c20000 {
> + compatible = "allwinner,sun50i-h5-ccu",
> + "allwinner,sun8i-h3-ccu";
> + };
If it doesn't have the same clocks, it's not compatible with the H3.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170127/c94c221b/attachment-0001.sig>
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
2017-01-26 15:48 ` Icenowy Zheng
(?)
(?)
@ 2017-01-27 15:59 ` Maxime Ripard
-1 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:59 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 492 bytes --]
On Thu, Jan 26, 2017 at 11:48:57PM +0800, Icenowy Zheng wrote:
> As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
> driver should be allowed to be built for ARM64, in order to make it work on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
Acked-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
@ 2017-01-27 15:59 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:59 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-gpio, dmaengine,
alsa-devel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 456 bytes --]
On Thu, Jan 26, 2017 at 11:48:57PM +0800, Icenowy Zheng wrote:
> As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
> driver should be allowed to be built for ARM64, in order to make it work on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
@ 2017-01-27 15:59 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:59 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, alsa-devel, Vinod Koul, Andre Przywara,
Linus Walleij, linux-sunxi, linux-kernel, Jaroslav Kysela,
linux-gpio, Chen-Yu Tsai, Mark Brown, dmaengine, linux-clk,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 456 bytes --]
On Thu, Jan 26, 2017 at 11:48:57PM +0800, Icenowy Zheng wrote:
> As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
> driver should be allowed to be built for ARM64, in order to make it work on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
@ 2017-01-27 15:59 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 15:59 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 26, 2017 at 11:48:57PM +0800, Icenowy Zheng wrote:
> As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
> driver should be allowed to be built for ARM64, in order to make it work on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170127/5091fa26/attachment.sig>
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
2017-01-26 15:48 ` Icenowy Zheng
(?)
(?)
@ 2017-01-27 20:05 ` Maxime Ripard
-1 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 20:05 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 534 bytes --]
On Thu, Jan 26, 2017 at 11:48:58PM +0800, Icenowy Zheng wrote:
> As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
> same digital part) as H3, enable the driver to be built on ARM64
> Allwinner platform, so that it can be used on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
Acked-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
@ 2017-01-27 20:05 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 20:05 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-gpio, dmaengine,
alsa-devel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 500 bytes --]
On Thu, Jan 26, 2017 at 11:48:58PM +0800, Icenowy Zheng wrote:
> As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
> same digital part) as H3, enable the driver to be built on ARM64
> Allwinner platform, so that it can be used on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
@ 2017-01-27 20:05 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 20:05 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, alsa-devel, Vinod Koul, Andre Przywara,
Linus Walleij, linux-sunxi, linux-kernel, Jaroslav Kysela,
linux-gpio, Chen-Yu Tsai, Mark Brown, dmaengine, linux-clk,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 500 bytes --]
On Thu, Jan 26, 2017 at 11:48:58PM +0800, Icenowy Zheng wrote:
> As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
> same digital part) as H3, enable the driver to be built on ARM64
> Allwinner platform, so that it can be used on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
@ 2017-01-27 20:05 ` Maxime Ripard
0 siblings, 0 replies; 69+ messages in thread
From: Maxime Ripard @ 2017-01-27 20:05 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 26, 2017 at 11:48:58PM +0800, Icenowy Zheng wrote:
> As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
> same digital part) as H3, enable the driver to be built on ARM64
> Allwinner platform, so that it can be used on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170127/82707ab0/attachment.sig>
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
2017-01-27 20:05 ` Maxime Ripard
(?)
(?)
@ 2017-01-28 12:46 ` Chen-Yu Tsai
-1 siblings, 0 replies; 69+ messages in thread
From: Chen-Yu Tsai @ 2017-01-28 12:46 UTC (permalink / raw)
To: Maxime Ripard
Cc: Icenowy Zheng, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara, linux-clk,
devicetree, linux-arm-kernel, linux-kernel,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA, Linux-ALSA, linux-sunxi
On Sat, Jan 28, 2017 at 4:05 AM, Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> On Thu, Jan 26, 2017 at 11:48:58PM +0800, Icenowy Zheng wrote:
>> As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
>> same digital part) as H3, enable the driver to be built on ARM64
>> Allwinner platform, so that it can be used on H5.
>>
>> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
>
> Acked-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Acked-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
@ 2017-01-28 12:46 ` Chen-Yu Tsai
0 siblings, 0 replies; 69+ messages in thread
From: Chen-Yu Tsai @ 2017-01-28 12:46 UTC (permalink / raw)
To: Maxime Ripard
Cc: Icenowy Zheng, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara, linux-clk,
devicetree, linux-arm-kernel, linux-kernel, linux-gpio,
dmaengine, Linux-ALSA, linux-sunxi
On Sat, Jan 28, 2017 at 4:05 AM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> On Thu, Jan 26, 2017 at 11:48:58PM +0800, Icenowy Zheng wrote:
>> As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
>> same digital part) as H3, enable the driver to be built on ARM64
>> Allwinner platform, so that it can be used on H5.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
>
> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
@ 2017-01-28 12:46 ` Chen-Yu Tsai
0 siblings, 0 replies; 69+ messages in thread
From: Chen-Yu Tsai @ 2017-01-28 12:46 UTC (permalink / raw)
To: Maxime Ripard
Cc: devicetree, Linux-ALSA, Vinod Koul, Andre Przywara,
Linus Walleij, linux-sunxi, linux-kernel, Jaroslav Kysela,
linux-gpio, Chen-Yu Tsai, Mark Brown, Icenowy Zheng, dmaengine,
linux-clk, linux-arm-kernel
On Sat, Jan 28, 2017 at 4:05 AM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> On Thu, Jan 26, 2017 at 11:48:58PM +0800, Icenowy Zheng wrote:
>> As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
>> same digital part) as H3, enable the driver to be built on ARM64
>> Allwinner platform, so that it can be used on H5.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
>
> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64
@ 2017-01-28 12:46 ` Chen-Yu Tsai
0 siblings, 0 replies; 69+ messages in thread
From: Chen-Yu Tsai @ 2017-01-28 12:46 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Jan 28, 2017 at 4:05 AM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> On Thu, Jan 26, 2017 at 11:48:58PM +0800, Icenowy Zheng wrote:
>> As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
>> same digital part) as H3, enable the driver to be built on ARM64
>> Allwinner platform, so that it can be used on H5.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
>
> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
2017-01-26 15:48 ` Icenowy Zheng
(?)
(?)
@ 2017-01-28 12:47 ` Chen-Yu Tsai
-1 siblings, 0 replies; 69+ messages in thread
From: Chen-Yu Tsai @ 2017-01-28 12:47 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara, linux-clk,
devicetree, linux-arm-kernel, linux-kernel,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA, Linux-ALSA, linux-sunxi
On Thu, Jan 26, 2017 at 11:48 PM, Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org> wrote:
> As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
^^^ typo
Otherwise,
Acked-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> driver should be allowed to be built for ARM64, in order to make it work on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
> ---
> New patch in v2, as H3 codec support is added between v1 and v2.
>
> drivers/dma/Kconfig | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
> index 0d6a96ee9fc7..d01d59812cf3 100644
> --- a/drivers/dma/Kconfig
> +++ b/drivers/dma/Kconfig
> @@ -157,7 +157,7 @@ config DMA_SUN4I
>
> config DMA_SUN6I
> tristate "Allwinner A31 SoCs DMA support"
> - depends on MACH_SUN6I || MACH_SUN8I || COMPILE_TEST
> + depends on MACH_SUN6I || MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
> depends on RESET_CONTROLLER
> select DMA_ENGINE
> select DMA_VIRTUAL_CHANNELS
> --
> 2.11.0
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
> For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [linux-sunxi] [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
@ 2017-01-28 12:47 ` Chen-Yu Tsai
0 siblings, 0 replies; 69+ messages in thread
From: Chen-Yu Tsai @ 2017-01-28 12:47 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, Vinod Koul,
Mark Brown, Jaroslav Kysela, Andre Przywara, linux-clk,
devicetree, linux-arm-kernel, linux-kernel, linux-gpio,
dmaengine, Linux-ALSA, linux-sunxi
On Thu, Jan 26, 2017 at 11:48 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
^^^ typo
Otherwise,
Acked-by: Chen-Yu Tsai <wens@csie.org>
> driver should be allowed to be built for ARM64, in order to make it work on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> New patch in v2, as H3 codec support is added between v1 and v2.
>
> drivers/dma/Kconfig | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
> index 0d6a96ee9fc7..d01d59812cf3 100644
> --- a/drivers/dma/Kconfig
> +++ b/drivers/dma/Kconfig
> @@ -157,7 +157,7 @@ config DMA_SUN4I
>
> config DMA_SUN6I
> tristate "Allwinner A31 SoCs DMA support"
> - depends on MACH_SUN6I || MACH_SUN8I || COMPILE_TEST
> + depends on MACH_SUN6I || MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
> depends on RESET_CONTROLLER
> select DMA_ENGINE
> select DMA_VIRTUAL_CHANNELS
> --
> 2.11.0
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [linux-sunxi] [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
@ 2017-01-28 12:47 ` Chen-Yu Tsai
0 siblings, 0 replies; 69+ messages in thread
From: Chen-Yu Tsai @ 2017-01-28 12:47 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Linux-ALSA, Vinod Koul, Andre Przywara,
Linus Walleij, linux-sunxi, linux-kernel, Jaroslav Kysela,
linux-gpio, Chen-Yu Tsai, Mark Brown, dmaengine, Maxime Ripard,
linux-clk, linux-arm-kernel
On Thu, Jan 26, 2017 at 11:48 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
^^^ typo
Otherwise,
Acked-by: Chen-Yu Tsai <wens@csie.org>
> driver should be allowed to be built for ARM64, in order to make it work on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> New patch in v2, as H3 codec support is added between v1 and v2.
>
> drivers/dma/Kconfig | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
> index 0d6a96ee9fc7..d01d59812cf3 100644
> --- a/drivers/dma/Kconfig
> +++ b/drivers/dma/Kconfig
> @@ -157,7 +157,7 @@ config DMA_SUN4I
>
> config DMA_SUN6I
> tristate "Allwinner A31 SoCs DMA support"
> - depends on MACH_SUN6I || MACH_SUN8I || COMPILE_TEST
> + depends on MACH_SUN6I || MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
> depends on RESET_CONTROLLER
> select DMA_ENGINE
> select DMA_VIRTUAL_CHANNELS
> --
> 2.11.0
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [linux-sunxi] [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
@ 2017-01-28 12:47 ` Chen-Yu Tsai
0 siblings, 0 replies; 69+ messages in thread
From: Chen-Yu Tsai @ 2017-01-28 12:47 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 26, 2017 at 11:48 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> As 64-bot Allwinner H5 SoC has the same DMA engine with H3, the DMA
^^^ typo
Otherwise,
Acked-by: Chen-Yu Tsai <wens@csie.org>
> driver should be allowed to be built for ARM64, in order to make it work on H5.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> New patch in v2, as H3 codec support is added between v1 and v2.
>
> drivers/dma/Kconfig | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
> index 0d6a96ee9fc7..d01d59812cf3 100644
> --- a/drivers/dma/Kconfig
> +++ b/drivers/dma/Kconfig
> @@ -157,7 +157,7 @@ config DMA_SUN4I
>
> config DMA_SUN6I
> tristate "Allwinner A31 SoCs DMA support"
> - depends on MACH_SUN6I || MACH_SUN8I || COMPILE_TEST
> + depends on MACH_SUN6I || MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
> depends on RESET_CONTROLLER
> select DMA_ENGINE
> select DMA_VIRTUAL_CHANNELS
> --
> 2.11.0
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
2017-01-26 15:48 ` Icenowy Zheng
(?)
(?)
@ 2017-01-30 15:13 ` Linus Walleij
-1 siblings, 0 replies; 69+ messages in thread
From: Linus Walleij @ 2017-01-30 15:13 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara, linux-clk,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
dmaengine-u79uwXL29TY76Z2rM5mHXA,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw, linux-sunxi
On Thu, Jan 26, 2017 at 4:48 PM, Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org> wrote:
> Based on the Allwinner H5 datasheet and the pinctrl driver of the
> backward-compatible H3 this introduces the pin multiplex assignments for
> the H5 SoC.
>
> H5 introduced some more pin functions (e.g. three more groups of TS
> pins, and one more groups of SIM pins) than H3.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
> ---
> Changes in v2:
> - Fixed interrupt banks. (There's one more GPIO banks (PF) that can do
> interrupt handling on H5)
Patch applied with Maxime's ACK.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
@ 2017-01-30 15:13 ` Linus Walleij
0 siblings, 0 replies; 69+ messages in thread
From: Linus Walleij @ 2017-01-30 15:13 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-gpio, dmaengine,
alsa-devel, linux-sunxi
On Thu, Jan 26, 2017 at 4:48 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> Based on the Allwinner H5 datasheet and the pinctrl driver of the
> backward-compatible H3 this introduces the pin multiplex assignments for
> the H5 SoC.
>
> H5 introduced some more pin functions (e.g. three more groups of TS
> pins, and one more groups of SIM pins) than H3.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v2:
> - Fixed interrupt banks. (There's one more GPIO banks (PF) that can do
> interrupt handling on H5)
Patch applied with Maxime's ACK.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 69+ messages in thread
* Re: [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
@ 2017-01-30 15:13 ` Linus Walleij
0 siblings, 0 replies; 69+ messages in thread
From: Linus Walleij @ 2017-01-30 15:13 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, alsa-devel, Vinod Koul, Andre Przywara, linux-sunxi,
linux-kernel, Jaroslav Kysela, linux-gpio, Chen-Yu Tsai,
Mark Brown, dmaengine, Maxime Ripard, linux-clk,
linux-arm-kernel
On Thu, Jan 26, 2017 at 4:48 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> Based on the Allwinner H5 datasheet and the pinctrl driver of the
> backward-compatible H3 this introduces the pin multiplex assignments for
> the H5 SoC.
>
> H5 introduced some more pin functions (e.g. three more groups of TS
> pins, and one more groups of SIM pins) than H3.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v2:
> - Fixed interrupt banks. (There's one more GPIO banks (PF) that can do
> interrupt handling on H5)
Patch applied with Maxime's ACK.
Yours,
Linus Walleij
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 69+ messages in thread
* [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC
@ 2017-01-30 15:13 ` Linus Walleij
0 siblings, 0 replies; 69+ messages in thread
From: Linus Walleij @ 2017-01-30 15:13 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 26, 2017 at 4:48 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> Based on the Allwinner H5 datasheet and the pinctrl driver of the
> backward-compatible H3 this introduces the pin multiplex assignments for
> the H5 SoC.
>
> H5 introduced some more pin functions (e.g. three more groups of TS
> pins, and one more groups of SIM pins) than H3.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> Changes in v2:
> - Fixed interrupt banks. (There's one more GPIO banks (PF) that can do
> interrupt handling on H5)
Patch applied with Maxime's ACK.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 69+ messages in thread
* Applied "ASoC: sunxi: allow the analog codec driver to be built on ARM64" to the asoc tree
2017-01-26 15:48 ` Icenowy Zheng
(?)
@ 2017-02-08 18:34 ` Mark Brown
-1 siblings, 0 replies; 69+ messages in thread
From: Mark Brown @ 2017-02-08 18:34 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, alsa-devel, Vinod Koul, Andre Przywara,
Linus Walleij, linux-sunxi, linux-kernel, Jaroslav Kysela,
linux-gpio, Chen-Yu Tsai, Mark Brown, dmaengine, Maxime Ripard,
linux-clk, linux-arm-kernel
The patch
ASoC: sunxi: allow the analog codec driver to be built on ARM64
has been applied to the asoc tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
>From e5028a259733ec2324893cb481023ed6cf7e9723 Mon Sep 17 00:00:00 2001
From: Icenowy Zheng <icenowy@aosc.xyz>
Date: Wed, 8 Feb 2017 02:30:40 +0800
Subject: [PATCH] ASoC: sunxi: allow the analog codec driver to be built on
ARM64
As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
same digital part) as H3, enable the driver to be built on ARM64
Allwinner platform, so that it can be used on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
sound/soc/sunxi/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/sound/soc/sunxi/Kconfig b/sound/soc/sunxi/Kconfig
index 13a8267f17c7..22408bc2d6ec 100644
--- a/sound/soc/sunxi/Kconfig
+++ b/sound/soc/sunxi/Kconfig
@@ -22,7 +22,7 @@ config SND_SUN8I_CODEC
config SND_SUN8I_CODEC_ANALOG
tristate "Allwinner sun8i Codec Analog Controls Support"
- depends on MACH_SUN8I || COMPILE_TEST
+ depends on MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
select REGMAP
help
Say Y or M if you want to add support for the analog controls for
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* Applied "ASoC: sunxi: allow the analog codec driver to be built on ARM64" to the asoc tree
@ 2017-02-08 18:34 ` Mark Brown
0 siblings, 0 replies; 69+ messages in thread
From: Mark Brown @ 2017-02-08 18:34 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Mark Brown, Maxime Ripard,
Chen-Yu Tsai, Linus Walleij, Vinod Koul, Mark Brown,
Jaroslav Kysela, Andre Przywara, devicetree, alsa-devel,
linux-kernel, linux-gpio, linux-sunxi, dmaengine, linux-clk,
linux-arm-kernel, alsa-devel
The patch
ASoC: sunxi: allow the analog codec driver to be built on ARM64
has been applied to the asoc tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
>From e5028a259733ec2324893cb481023ed6cf7e9723 Mon Sep 17 00:00:00 2001
From: Icenowy Zheng <icenowy@aosc.xyz>
Date: Wed, 8 Feb 2017 02:30:40 +0800
Subject: [PATCH] ASoC: sunxi: allow the analog codec driver to be built on
ARM64
As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
same digital part) as H3, enable the driver to be built on ARM64
Allwinner platform, so that it can be used on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
sound/soc/sunxi/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/sound/soc/sunxi/Kconfig b/sound/soc/sunxi/Kconfig
index 13a8267f17c7..22408bc2d6ec 100644
--- a/sound/soc/sunxi/Kconfig
+++ b/sound/soc/sunxi/Kconfig
@@ -22,7 +22,7 @@ config SND_SUN8I_CODEC
config SND_SUN8I_CODEC_ANALOG
tristate "Allwinner sun8i Codec Analog Controls Support"
- depends on MACH_SUN8I || COMPILE_TEST
+ depends on MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
select REGMAP
help
Say Y or M if you want to add support for the analog controls for
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
* Applied "ASoC: sunxi: allow the analog codec driver to be built on ARM64" to the asoc tree
@ 2017-02-08 18:34 ` Mark Brown
0 siblings, 0 replies; 69+ messages in thread
From: Mark Brown @ 2017-02-08 18:34 UTC (permalink / raw)
To: linux-arm-kernel
The patch
ASoC: sunxi: allow the analog codec driver to be built on ARM64
has been applied to the asoc tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
>From e5028a259733ec2324893cb481023ed6cf7e9723 Mon Sep 17 00:00:00 2001
From: Icenowy Zheng <icenowy@aosc.xyz>
Date: Wed, 8 Feb 2017 02:30:40 +0800
Subject: [PATCH] ASoC: sunxi: allow the analog codec driver to be built on
ARM64
As the 64-bit Allwinner H5 SoC has the same analog codec part (also the
same digital part) as H3, enable the driver to be built on ARM64
Allwinner platform, so that it can be used on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
sound/soc/sunxi/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/sound/soc/sunxi/Kconfig b/sound/soc/sunxi/Kconfig
index 13a8267f17c7..22408bc2d6ec 100644
--- a/sound/soc/sunxi/Kconfig
+++ b/sound/soc/sunxi/Kconfig
@@ -22,7 +22,7 @@ config SND_SUN8I_CODEC
config SND_SUN8I_CODEC_ANALOG
tristate "Allwinner sun8i Codec Analog Controls Support"
- depends on MACH_SUN8I || COMPILE_TEST
+ depends on MACH_SUN8I || (ARM64 && ARCH_SUNXI) || COMPILE_TEST
select REGMAP
help
Say Y or M if you want to add support for the analog controls for
--
2.11.0
^ permalink raw reply related [flat|nested] 69+ messages in thread
end of thread, other threads:[~2017-02-08 18:39 UTC | newest]
Thread overview: 69+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-01-26 15:48 [PATCH v2 0/9] Allwinner H5 and Orange Pi PC2 support Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
[not found] ` <20170126154859.55855-1-icenowy-ymACFijhrKM@public.gmane.org>
2017-01-26 15:48 ` [PATCH v2 1/9] drivers: pinctrl: add driver for Allwinner H5 SoC Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
[not found] ` <20170126154859.55855-2-icenowy-ymACFijhrKM@public.gmane.org>
2017-01-27 15:51 ` Maxime Ripard
2017-01-27 15:51 ` Maxime Ripard
2017-01-27 15:51 ` Maxime Ripard
2017-01-27 15:51 ` Maxime Ripard
2017-01-30 15:13 ` Linus Walleij
2017-01-30 15:13 ` Linus Walleij
2017-01-30 15:13 ` Linus Walleij
2017-01-30 15:13 ` Linus Walleij
2017-01-26 15:48 ` [PATCH v2 2/9] arm64: allwinner: Kconfig: add essential pinctrl driver for H5 Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` [PATCH v2 3/9] clk: sunxi-ng: add support for Allwinner H5 SoC Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
[not found] ` <20170126154859.55855-4-icenowy-ymACFijhrKM@public.gmane.org>
2017-01-27 15:53 ` Maxime Ripard
2017-01-27 15:53 ` Maxime Ripard
2017-01-27 15:53 ` Maxime Ripard
2017-01-27 15:53 ` Maxime Ripard
2017-01-26 15:48 ` [PATCH v2 4/9] arm: dts: sun8i: split Allwinner H3 .dtsi Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
[not found] ` <20170126154859.55855-5-icenowy-ymACFijhrKM@public.gmane.org>
2017-01-27 15:55 ` Maxime Ripard
2017-01-27 15:55 ` Maxime Ripard
2017-01-27 15:55 ` Maxime Ripard
2017-01-27 15:55 ` Maxime Ripard
2017-01-26 15:48 ` [PATCH v2 6/9] arm64: dts: allwinner: add Allwinner H5 .dtsi Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
[not found] ` <20170126154859.55855-7-icenowy-ymACFijhrKM@public.gmane.org>
2017-01-27 15:58 ` Maxime Ripard
2017-01-27 15:58 ` Maxime Ripard
2017-01-27 15:58 ` Maxime Ripard
2017-01-27 15:58 ` Maxime Ripard
2017-01-26 15:48 ` [PATCH v2 7/9] dmaengine: sun6i: allow build on ARM64 platforms (sun50i) Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
[not found] ` <20170126154859.55855-8-icenowy-ymACFijhrKM@public.gmane.org>
2017-01-27 15:59 ` Maxime Ripard
2017-01-27 15:59 ` Maxime Ripard
2017-01-27 15:59 ` Maxime Ripard
2017-01-27 15:59 ` Maxime Ripard
2017-01-28 12:47 ` Chen-Yu Tsai
2017-01-28 12:47 ` [linux-sunxi] " Chen-Yu Tsai
2017-01-28 12:47 ` Chen-Yu Tsai
2017-01-28 12:47 ` Chen-Yu Tsai
2017-01-26 15:48 ` [PATCH v2 8/9] ASoC: sunxi: allow the analog codec driver to be built on ARM64 Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
[not found] ` <20170126154859.55855-9-icenowy-ymACFijhrKM@public.gmane.org>
2017-01-27 20:05 ` Maxime Ripard
2017-01-27 20:05 ` Maxime Ripard
2017-01-27 20:05 ` Maxime Ripard
2017-01-27 20:05 ` Maxime Ripard
2017-01-28 12:46 ` Chen-Yu Tsai
2017-01-28 12:46 ` Chen-Yu Tsai
2017-01-28 12:46 ` Chen-Yu Tsai
2017-01-28 12:46 ` Chen-Yu Tsai
2017-02-08 18:34 ` Applied "ASoC: sunxi: allow the analog codec driver to be built on ARM64" to the asoc tree Mark Brown
2017-02-08 18:34 ` Mark Brown
2017-02-08 18:34 ` Mark Brown
2017-01-26 15:48 ` [PATCH v2 9/9] arm64: dts: sunxi: add support for the Orange Pi PC 2 board Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` [PATCH v2 5/9] clk: sunxi-ng: remove transitional headers for dt-bindings Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
2017-01-26 15:48 ` Icenowy Zheng
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.