[net-next 06/12] i40e: allow look-up of MAC address from Open Firmware or IDPROM

[Jeff Kirsher <jeffrey.t.kirsher@intel.com>]

From: Jacob Keller <jacob.e.keller@intel.com>

Look up the MAC address from the eth_get_platform_mac_address() function
first before checking what the firmware provides. We already handle the
case of re-writing the MAC-VLAN filter, so there is no need to add extra
code for this. However, update the comment where we do this to indicate
that it does impact the Open Firmware MAC address case.

Change-ID: I73e59fbe0b0e7e6f3ee9f5170d0bd3a4d5faf4db
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/i40e/i40e_main.c | 29 ++++++++++++++++-------------
 1 file changed, 16 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 22831a4a9099..2111f120865a 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -9326,10 +9326,15 @@ static int i40e_config_netdev(struct i40e_vsi *vsi)
 	if (vsi->type == I40E_VSI_MAIN) {
 		SET_NETDEV_DEV(netdev, &pf->pdev->dev);
 		ether_addr_copy(mac_addr, hw->mac.perm_addr);
-		/* The following steps are necessary to properly keep track of
-		 * MAC-VLAN filters loaded into firmware - first we remove
-		 * filter that is automatically generated by firmware and then
-		 * add new filter both to the driver hash table and firmware.
+		/* The following steps are necessary for two reasons. First,
+		 * some older NVM configurations load a default MAC-VLAN
+		 * filter that will accept any tagged packet, and we want to
+		 * replace this with a normal filter. Additionally, it is
+		 * possible our MAC address was provided by the platform using
+		 * Open Firmware or similar.
+		 *
+		 * Thus, we need to remove the default filter and install one
+		 * specific to the MAC address.
 		 */
 		i40e_rm_default_mac_filter(vsi, mac_addr);
 		spin_lock_bh(&vsi->mac_filter_hash_lock);
@@ -10834,20 +10839,18 @@ static void i40e_print_features(struct i40e_pf *pf)
 
 /**
  * i40e_get_platform_mac_addr - get platform-specific MAC address
- *
  * @pdev: PCI device information struct
  * @pf: board private structure
  *
- * Look up the MAC address in Open Firmware  on systems that support it,
- * and use IDPROM on SPARC if no OF address is found. On return, the
- * I40E_FLAG_PF_MAC will be wset in pf->flags if a platform-specific value
- * has been selected.
+ * Look up the MAC address for the device. First we'll try
+ * eth_platform_get_mac_address, which will check Open Firmware, or arch
+ * specific fallback. Otherwise, we'll default to the stored value in
+ * firmware.
  **/
 static void i40e_get_platform_mac_addr(struct pci_dev *pdev, struct i40e_pf *pf)
 {
-	pf->flags &= ~I40E_FLAG_PF_MAC;
-	if (!eth_platform_get_mac_address(&pdev->dev, pf->hw.mac.addr))
-		pf->flags |= I40E_FLAG_PF_MAC;
+	if (eth_platform_get_mac_address(&pdev->dev, pf->hw.mac.addr))
+		i40e_get_mac_addr(&pf->hw, pf->hw.mac.addr);
 }
 
 /**
@@ -11061,9 +11064,9 @@ static int i40e_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 		i40e_aq_stop_lldp(hw, true, NULL);
 	}
 
-	i40e_get_mac_addr(hw, hw->mac.addr);
 	/* allow a platform config to override the HW addr */
 	i40e_get_platform_mac_addr(pdev, pf);
+
 	if (!is_valid_ether_addr(hw->mac.addr)) {
 		dev_info(&pdev->dev, "invalid MAC address %pM\n", hw->mac.addr);
 		err = -EIO;
-- 
2.12.2