All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v24 00/11] acpi, clocksource: add GTDT driver and GTDT support in arm_arch_timer
@ 2017-04-14 18:40 ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

This patchset:
    (1)Preparation for adding GTDT support in arm_arch_timer:
        1. Introduce a MMIO CNTFRQ helper.
        2. separate out device-tree code from arch_timer_detect_rate
        3. replace arch_timer_detect_rate with arch_timer_of_configure_rate
        4. Refactor arch_timer_needs_probing, and move it into DT init call
        5. Introduce some new structs and refactor the MMIO timer init code
        for reusing some common code.

    (2)Introduce ACPI GTDT parser: drivers/acpi/arm64/gtdt.c
    Parse all kinds of timer in GTDT table of ACPI:arch timer,
    memory-mapped timer and SBSA Generic Watchdog timer.
    This driver can help to simplify all the relevant timer drivers,
    and separate all the ACPI GTDT knowledge from them.

    (3)Simplify ACPI code for arm_arch_timer

    (4)Add GTDT support for ARM memory-mapped timer.

This patchset has been tested on the following platforms with ACPI enabled:
    (1)ARM Foundation v8 model

Changelog:
v24: https://lkml.org/lkml/2017/4/14/
     Mark Rutland:
         Rework comments
         Refactor the probing split
         Verify CNTFRQ:arch_timer_mem_verify_cntfrq
         Only register the first frame:arch_timer_mem_find_best_frame
     Fu Wei:
         Fetches from git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux.git arch-timer/gtdt
         Introduces acpi_unregister_irq function, and use it in drivers/acpi/arm64/gtdt.c

v23: https://lkml.org/lkml/2017/3/31/629
     Rebase to git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux.git arch-timer/cleanup
     Improve the data struct of arch_timer_mem and arch_timer_mem_frame to
     improve the parser of GT blocks and arch_timer_mem initualization.
     Improve arch_timer_rate detection: sysreg frequency is primary in DT boot
     Improve some comments in GTDT parser driver.
     Improve acpi_gtdt_init function, and make a comment for the multiple calls.
     Improve the unwinding for the irq of timers, when an error occurs.
     Handle the case of virtual timer GSIV is 0.

v22: https://lkml.org/lkml/2017/3/21/523
     Rebase to git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux.git arch-timer/cleanup
     Only Introduce arch_timer_mem_get_cntfrq to get the frequency from mmio.
     Merged patch 2,3(about arch_timer_detect_rate).
     Keep arch_timer_rate, do NOT split it for different types of timer.
     Improve  memory-mapped timer support by comments and variable name:
         data-->timer_mem
         frame-->gtdt_frame
     Delete zero check for SBSA watchdog irq.
     Skip secure SBSA watchdog in GTDT driver.
     Delete Kconfig modification for SBSA watchdog driver.
     Delete no_irq, using nr_res instead.

v21: https://lkml.org/lkml/2017/2/6/734
     Introduce two functions to get the frequency from mmio and sysreg.
     Remove arch_timer_detect_rate use arch_timer_get_*_freq directly
     Split arch_timer_rate for different types of timer.
     Skip secure timer frame in GTDT driver.
     Rebase to git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux.git arch-timer/cleanup
     (The first 6 patches in v20 have been merged into arch-timer/cleanup branch)

v20: https://lkml.org/lkml/2017/1/18/534
     Reorder the first 4 patches and split the 4th patches.
     Leave CNTHCTL_* as they originally were.
     Fix the bug in arch_timer_select_ppi.
     Split "Rework counter frequency detection" patch.
     Rework the arch_timer_detect_rate function.
     Improve the commit message of "Refactor MMIO timer probing".
     Rebase to 4.10.0-rc4

v19: https://lkml.org/lkml/2016/12/21/25
     Fix a '\n' missing in a error message in arch_timer_mem_init.
     Add "request_mem_region" for ioremapping cntbase, according to
     f947ee1 clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
     Rebase to 4.9.0-gfb779ff

v18: https://lkml.org/lkml/2016/12/8/446
     Fix 8/15 patch problem of "int ret;" in arch_timer_acpi_init.
     Rebase to 4.9.0-rc8-g9269898

v17: https://lkml.org/lkml/2016/11/25/140
     Take out some cleanups from 4/15.
     Merge 5/15 and 6/15, improve PPI determination code,
     improve commit message.
     Rework counter frequency detection.
     Move arch_timer_needs_of_probing into DT init call.
     Move Platform Timer scan loop back to timer init call to avoid allocating
     and free memory.
     Improve all the exported functions' comment.

v16: https://lkml.org/lkml/2016/11/16/268
     Fix patchset problem about static enum ppi_nr of 01/13 in v15.
     Refactor arch_timer_detect_rate.
     Refactor arch_timer_needs_probing.

v15: https://lkml.org/lkml/2016/11/15/366
     Re-order patches
     Add arm_arch_timer refactoring patches to prepare for GTDT:
         1. rename some  enums and defines, and some cleanups
         2. separate out arch_timer_uses_ppi init code and fix a potential bug
         3. Improve some new structs, refactor the timer init code.
     Since the some structs have been changed, GTDT parser for memory-mapped
     timer and SBSA Generic Watchdog timer have been update.

v14: https://lkml.org/lkml/2016/9/28/573
     Separate memory-mapped timer GTDT support into two patches
         1. Refactor the timer init code to prepare for GTDT
         2. Add GTDT support for memory-mapped timer

v13: http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1231717.html
     Improve arm_arch_timer code for memory-mapped
     timer GTDT support, refactor original memory-mapped timer
     dt support for reusing some common code.

v12: https://lkml.org/lkml/2016/9/13/250
     Rebase to latest Linux 4.8-rc6
     Delete the confusing "skipping" in the error message.

V11: https://lkml.org/lkml/2016/9/6/354
     Rebase to latest Linux 4.8-rc5
     Delete typedef (suggested by checkpatch.pl)

V10: https://lkml.org/lkml/2016/7/26/215
     Drop the "readq" patch.
     Rebase to latest Linux 4.7.

V9: https://lkml.org/lkml/2016/7/25/345
    Improve pr_err message in acpi gtdt driver.
    Update Commit message for 7/9
    shorten the irq mapping function name
    Improve GTDT driver for memory-mapped timer

v8: https://lkml.org/lkml/2016/7/19/660
    Improve "pr_fmt(fmt)" definition: add "ACPI" in front of "GTDT",
    and also improve printk message.
    Simplify is_timer_block and is_watchdog.
    Merge acpi_gtdt_desc_init and gtdt_arch_timer_init into acpi_gtdt_init();
    Delete __init in include/linux/acpi.h for GTDT API
    Make ARM64 select GTDT.
    Delete "#include <linux/module.h>" from acpi_gtdt.c
    Simplify GT block parse code.

v7: https://lkml.org/lkml/2016/7/13/769
    Move the GTDT driver to drivers/acpi/arm64
    Add add the ARM64-specific ACPI Support maintainers in MAINTAINERS
    Merge 3 patches of GTDT parser driver.
    Fix the for_each_platform_timer bug.

v6: https://lkml.org/lkml/2016/6/29/580
    split the GTDT driver to 4 parts: basic, arch_timer, memory-mapped timer,
    and SBSA Generic Watchdog timer
    Improve driver by suggestions and example code from Daniel Lezcano

v5: https://lkml.org/lkml/2016/5/24/356
    Sorting out all patches, simplify the API of GTDT driver:
    GTDT driver just fills the data struct for arm_arch_timer driver.

v4: https://lists.linaro.org/pipermail/linaro-acpi/2016-March/006667.html
    Delete the kvm relevant patches
    Separate two patches for sorting out the code for arm_arch_timer.
    Improve irq info export code to allow missing irq info in GTDT table.

v3: https://lkml.org/lkml/2016/2/1/658
    Improve GTDT driver code:
      (1)improve pr_* by defining pr_fmt(fmt)
      (2)simplify gtdt_sbsa_gwdt_init
      (3)improve gtdt_arch_timer_data_init, if table is NULL, it will try
      to get GTDT table.
    Move enum ppi_nr to arm_arch_timer.h, and add enum spi_nr.
    Add arm_arch_timer get ppi from DT and GTDT support for kvm.

v2: https://lkml.org/lkml/2015/12/2/10
    Rebase to latest kernel version(4.4-rc3).
    Fix the bug about the config problem,
    use CONFIG_ACPI_GTDT instead of CONFIG_ACPI in arm_arch_timer.c

v1: The first upstreaming version: https://lkml.org/lkml/2015/10/28/553

Fu Wei (11):
  clocksource: arm_arch_timer: split dt-only rate handling
  clocksource: arm_arch_timer: refactor arch_timer_needs_probing
  clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT
    init call
  clocksource: arm_arch_timer: add structs to describe MMIO timer
  clocksource: arm_arch_timer: split MMIO timer probing.
  acpi/arm64: Add GTDT table parse driver
  clocksource: arm_arch_timer: simplify ACPI support code.
  acpi: Add acpi_unregister_irq function
  acpi/arm64: Add memory-mapped timer support in GTDT driver
  clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
  acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver

 arch/arm64/Kconfig                   |   1 +
 drivers/acpi/arm64/Kconfig           |   3 +
 drivers/acpi/arm64/Makefile          |   1 +
 drivers/acpi/arm64/gtdt.c            | 404 +++++++++++++++++++++++++++++++++++
 drivers/acpi/irq.c                   |  10 +
 drivers/clocksource/arm_arch_timer.c | 393 ++++++++++++++++++++++++----------
 include/clocksource/arm_arch_timer.h |  16 ++
 include/linux/acpi.h                 |  14 ++
 8 files changed, 724 insertions(+), 118 deletions(-)
 create mode 100644 drivers/acpi/arm64/gtdt.c

-- 
2.9.3


^ permalink raw reply	[flat|nested] 41+ messages in thread

* [PATCH v24 00/11] acpi, clocksource: add GTDT driver and GTDT support in arm_arch_timer
@ 2017-04-14 18:40 ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

This patchset:
    (1)Preparation for adding GTDT support in arm_arch_timer:
        1. Introduce a MMIO CNTFRQ helper.
        2. separate out device-tree code from arch_timer_detect_rate
        3. replace arch_timer_detect_rate with arch_timer_of_configure_rate
        4. Refactor arch_timer_needs_probing, and move it into DT init call
        5. Introduce some new structs and refactor the MMIO timer init code
        for reusing some common code.

    (2)Introduce ACPI GTDT parser: drivers/acpi/arm64/gtdt.c
    Parse all kinds of timer in GTDT table of ACPI:arch timer,
    memory-mapped timer and SBSA Generic Watchdog timer.
    This driver can help to simplify all the relevant timer drivers,
    and separate all the ACPI GTDT knowledge from them.

    (3)Simplify ACPI code for arm_arch_timer

    (4)Add GTDT support for ARM memory-mapped timer.

This patchset has been tested on the following platforms with ACPI enabled:
    (1)ARM Foundation v8 model

Changelog:
v24: https://lkml.org/lkml/2017/4/14/
     Mark Rutland:
         Rework comments
         Refactor the probing split
         Verify CNTFRQ:arch_timer_mem_verify_cntfrq
         Only register the first frame:arch_timer_mem_find_best_frame
     Fu Wei:
         Fetches from git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux.git arch-timer/gtdt
         Introduces acpi_unregister_irq function, and use it in drivers/acpi/arm64/gtdt.c

v23: https://lkml.org/lkml/2017/3/31/629
     Rebase to git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux.git arch-timer/cleanup
     Improve the data struct of arch_timer_mem and arch_timer_mem_frame to
     improve the parser of GT blocks and arch_timer_mem initualization.
     Improve arch_timer_rate detection: sysreg frequency is primary in DT boot
     Improve some comments in GTDT parser driver.
     Improve acpi_gtdt_init function, and make a comment for the multiple calls.
     Improve the unwinding for the irq of timers, when an error occurs.
     Handle the case of virtual timer GSIV is 0.

v22: https://lkml.org/lkml/2017/3/21/523
     Rebase to git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux.git arch-timer/cleanup
     Only Introduce arch_timer_mem_get_cntfrq to get the frequency from mmio.
     Merged patch 2,3(about arch_timer_detect_rate).
     Keep arch_timer_rate, do NOT split it for different types of timer.
     Improve  memory-mapped timer support by comments and variable name:
         data-->timer_mem
         frame-->gtdt_frame
     Delete zero check for SBSA watchdog irq.
     Skip secure SBSA watchdog in GTDT driver.
     Delete Kconfig modification for SBSA watchdog driver.
     Delete no_irq, using nr_res instead.

v21: https://lkml.org/lkml/2017/2/6/734
     Introduce two functions to get the frequency from mmio and sysreg.
     Remove arch_timer_detect_rate use arch_timer_get_*_freq directly
     Split arch_timer_rate for different types of timer.
     Skip secure timer frame in GTDT driver.
     Rebase to git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux.git arch-timer/cleanup
     (The first 6 patches in v20 have been merged into arch-timer/cleanup branch)

v20: https://lkml.org/lkml/2017/1/18/534
     Reorder the first 4 patches and split the 4th patches.
     Leave CNTHCTL_* as they originally were.
     Fix the bug in arch_timer_select_ppi.
     Split "Rework counter frequency detection" patch.
     Rework the arch_timer_detect_rate function.
     Improve the commit message of "Refactor MMIO timer probing".
     Rebase to 4.10.0-rc4

v19: https://lkml.org/lkml/2016/12/21/25
     Fix a '\n' missing in a error message in arch_timer_mem_init.
     Add "request_mem_region" for ioremapping cntbase, according to
     f947ee1 clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
     Rebase to 4.9.0-gfb779ff

v18: https://lkml.org/lkml/2016/12/8/446
     Fix 8/15 patch problem of "int ret;" in arch_timer_acpi_init.
     Rebase to 4.9.0-rc8-g9269898

v17: https://lkml.org/lkml/2016/11/25/140
     Take out some cleanups from 4/15.
     Merge 5/15 and 6/15, improve PPI determination code,
     improve commit message.
     Rework counter frequency detection.
     Move arch_timer_needs_of_probing into DT init call.
     Move Platform Timer scan loop back to timer init call to avoid allocating
     and free memory.
     Improve all the exported functions' comment.

v16: https://lkml.org/lkml/2016/11/16/268
     Fix patchset problem about static enum ppi_nr of 01/13 in v15.
     Refactor arch_timer_detect_rate.
     Refactor arch_timer_needs_probing.

v15: https://lkml.org/lkml/2016/11/15/366
     Re-order patches
     Add arm_arch_timer refactoring patches to prepare for GTDT:
         1. rename some  enums and defines, and some cleanups
         2. separate out arch_timer_uses_ppi init code and fix a potential bug
         3. Improve some new structs, refactor the timer init code.
     Since the some structs have been changed, GTDT parser for memory-mapped
     timer and SBSA Generic Watchdog timer have been update.

v14: https://lkml.org/lkml/2016/9/28/573
     Separate memory-mapped timer GTDT support into two patches
         1. Refactor the timer init code to prepare for GTDT
         2. Add GTDT support for memory-mapped timer

v13: http://www.mail-archive.com/linux-kernel at vger.kernel.org/msg1231717.html
     Improve arm_arch_timer code for memory-mapped
     timer GTDT support, refactor original memory-mapped timer
     dt support for reusing some common code.

v12: https://lkml.org/lkml/2016/9/13/250
     Rebase to latest Linux 4.8-rc6
     Delete the confusing "skipping" in the error message.

V11: https://lkml.org/lkml/2016/9/6/354
     Rebase to latest Linux 4.8-rc5
     Delete typedef (suggested by checkpatch.pl)

V10: https://lkml.org/lkml/2016/7/26/215
     Drop the "readq" patch.
     Rebase to latest Linux 4.7.

V9: https://lkml.org/lkml/2016/7/25/345
    Improve pr_err message in acpi gtdt driver.
    Update Commit message for 7/9
    shorten the irq mapping function name
    Improve GTDT driver for memory-mapped timer

v8: https://lkml.org/lkml/2016/7/19/660
    Improve "pr_fmt(fmt)" definition: add "ACPI" in front of "GTDT",
    and also improve printk message.
    Simplify is_timer_block and is_watchdog.
    Merge acpi_gtdt_desc_init and gtdt_arch_timer_init into acpi_gtdt_init();
    Delete __init in include/linux/acpi.h for GTDT API
    Make ARM64 select GTDT.
    Delete "#include <linux/module.h>" from acpi_gtdt.c
    Simplify GT block parse code.

v7: https://lkml.org/lkml/2016/7/13/769
    Move the GTDT driver to drivers/acpi/arm64
    Add add the ARM64-specific ACPI Support maintainers in MAINTAINERS
    Merge 3 patches of GTDT parser driver.
    Fix the for_each_platform_timer bug.

v6: https://lkml.org/lkml/2016/6/29/580
    split the GTDT driver to 4 parts: basic, arch_timer, memory-mapped timer,
    and SBSA Generic Watchdog timer
    Improve driver by suggestions and example code from Daniel Lezcano

v5: https://lkml.org/lkml/2016/5/24/356
    Sorting out all patches, simplify the API of GTDT driver:
    GTDT driver just fills the data struct for arm_arch_timer driver.

v4: https://lists.linaro.org/pipermail/linaro-acpi/2016-March/006667.html
    Delete the kvm relevant patches
    Separate two patches for sorting out the code for arm_arch_timer.
    Improve irq info export code to allow missing irq info in GTDT table.

v3: https://lkml.org/lkml/2016/2/1/658
    Improve GTDT driver code:
      (1)improve pr_* by defining pr_fmt(fmt)
      (2)simplify gtdt_sbsa_gwdt_init
      (3)improve gtdt_arch_timer_data_init, if table is NULL, it will try
      to get GTDT table.
    Move enum ppi_nr to arm_arch_timer.h, and add enum spi_nr.
    Add arm_arch_timer get ppi from DT and GTDT support for kvm.

v2: https://lkml.org/lkml/2015/12/2/10
    Rebase to latest kernel version(4.4-rc3).
    Fix the bug about the config problem,
    use CONFIG_ACPI_GTDT instead of CONFIG_ACPI in arm_arch_timer.c

v1: The first upstreaming version: https://lkml.org/lkml/2015/10/28/553

Fu Wei (11):
  clocksource: arm_arch_timer: split dt-only rate handling
  clocksource: arm_arch_timer: refactor arch_timer_needs_probing
  clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT
    init call
  clocksource: arm_arch_timer: add structs to describe MMIO timer
  clocksource: arm_arch_timer: split MMIO timer probing.
  acpi/arm64: Add GTDT table parse driver
  clocksource: arm_arch_timer: simplify ACPI support code.
  acpi: Add acpi_unregister_irq function
  acpi/arm64: Add memory-mapped timer support in GTDT driver
  clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
  acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver

 arch/arm64/Kconfig                   |   1 +
 drivers/acpi/arm64/Kconfig           |   3 +
 drivers/acpi/arm64/Makefile          |   1 +
 drivers/acpi/arm64/gtdt.c            | 404 +++++++++++++++++++++++++++++++++++
 drivers/acpi/irq.c                   |  10 +
 drivers/clocksource/arm_arch_timer.c | 393 ++++++++++++++++++++++++----------
 include/clocksource/arm_arch_timer.h |  16 ++
 include/linux/acpi.h                 |  14 ++
 8 files changed, 724 insertions(+), 118 deletions(-)
 create mode 100644 drivers/acpi/arm64/gtdt.c

-- 
2.9.3

^ permalink raw reply	[flat|nested] 41+ messages in thread

* [PATCH v24 01/11] clocksource: arm_arch_timer: split dt-only rate handling
  2017-04-14 18:40 ` fu.wei at linaro.org
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

For historical reasons, rate detection when probing via DT is somewhat
convoluted. We tried to package this up in arch_timer_detect_rate(), but
with the addition of ACPI worse, and gets in the way of stringent rate
checking when ACPI is used.

This patch makes arch_timer_detect_rate() specific to DT, ripping out
ACPI logic. In preparation for rework of the MMIO timer probing, the
reading of the relevant CNTFRQ register is factored out to callers. The
function is then renamed to arch_timer_of_configure_rate(), which better
represents its new place in the world.

Comments are added in the DT and ACPI probe paths to explain this.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
[Mark: reword commit message, TODO: rework comments]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 41 ++++++++++++++++++++----------------
 1 file changed, 23 insertions(+), 18 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 94de018..0138b0c 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -818,24 +818,19 @@ static int arch_timer_starting_cpu(unsigned int cpu)
 	return 0;
 }
 
-static void
-arch_timer_detect_rate(void __iomem *cntbase, struct device_node *np)
+/*
+ * For historical reasons, when probing with DT we use whichever (non-zero)
+ * rate was probed first, and don't verify that others match. If the first node
+ * probed has a clock-frequency property, this overrides the HW register.
+ */
+static void arch_timer_of_configure_rate(u32 rate, struct device_node *np)
 {
 	/* Who has more than one independent system counter? */
 	if (arch_timer_rate)
 		return;
 
-	/*
-	 * Try to determine the frequency from the device tree or CNTFRQ,
-	 * if ACPI is enabled, get the frequency from CNTFRQ ONLY.
-	 */
-	if (!acpi_disabled ||
-	    of_property_read_u32(np, "clock-frequency", &arch_timer_rate)) {
-		if (cntbase)
-			arch_timer_rate = readl_relaxed(cntbase + CNTFRQ);
-		else
-			arch_timer_rate = arch_timer_get_cntfrq();
-	}
+	if (of_property_read_u32(np, "clock-frequency", &arch_timer_rate))
+		arch_timer_rate = rate;
 
 	/* Check the timer frequency. */
 	if (arch_timer_rate == 0)
@@ -1166,6 +1161,7 @@ static int __init arch_timer_init(void)
 static int __init arch_timer_of_init(struct device_node *np)
 {
 	int i;
+	u32 rate;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
 		pr_warn("multiple nodes in dt, skipping\n");
@@ -1176,7 +1172,8 @@ static int __init arch_timer_of_init(struct device_node *np)
 	for (i = ARCH_TIMER_PHYS_SECURE_PPI; i < ARCH_TIMER_MAX_TIMER_PPI; i++)
 		arch_timer_ppi[i] = irq_of_parse_and_map(np, i);
 
-	arch_timer_detect_rate(NULL, np);
+	rate = arch_timer_get_cntfrq();
+	arch_timer_of_configure_rate(rate, np);
 
 	arch_timer_c3stop = !of_property_read_bool(np, "always-on");
 
@@ -1212,7 +1209,7 @@ static int __init arch_timer_mem_init(struct device_node *np)
 	struct device_node *frame, *best_frame = NULL;
 	void __iomem *cntctlbase, *base;
 	unsigned int irq, ret = -EINVAL;
-	u32 cnttidr;
+	u32 cnttidr, rate;
 
 	arch_timers_present |= ARCH_TIMER_TYPE_MEM;
 	cntctlbase = of_iomap(np, 0);
@@ -1278,7 +1275,8 @@ static int __init arch_timer_mem_init(struct device_node *np)
 		goto out;
 	}
 
-	arch_timer_detect_rate(base, np);
+	rate = readl(base + CNTFRQ);
+	arch_timer_of_configure_rate(rate, np);
 	ret = arch_timer_mem_register(base, irq);
 	if (ret)
 		goto out;
@@ -1339,8 +1337,15 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 		map_generic_timer_interrupt(gtdt->non_secure_el2_interrupt,
 		gtdt->non_secure_el2_flags);
 
-	/* Get the frequency from CNTFRQ */
-	arch_timer_detect_rate(NULL, NULL);
+	/*
+	 * When probing via ACPI, we have no mechanism to override the sysreg
+	 * CNTFRQ value. This *must* be correct.
+	 */
+	arch_timer_rate = arch_timer_get_cntfrq();
+	if (!arch_timer_rate) {
+		pr_err(FW_BUG "frequency not available.\n");
+		return -EINVAL;
+	}
 
 	arch_timer_uses_ppi = arch_timer_select_ppi();
 	if (!arch_timer_ppi[arch_timer_uses_ppi]) {
-- 
2.9.3


^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 01/11] clocksource: arm_arch_timer: split dt-only rate handling
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

For historical reasons, rate detection when probing via DT is somewhat
convoluted. We tried to package this up in arch_timer_detect_rate(), but
with the addition of ACPI worse, and gets in the way of stringent rate
checking when ACPI is used.

This patch makes arch_timer_detect_rate() specific to DT, ripping out
ACPI logic. In preparation for rework of the MMIO timer probing, the
reading of the relevant CNTFRQ register is factored out to callers. The
function is then renamed to arch_timer_of_configure_rate(), which better
represents its new place in the world.

Comments are added in the DT and ACPI probe paths to explain this.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
[Mark: reword commit message, TODO: rework comments]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 41 ++++++++++++++++++++----------------
 1 file changed, 23 insertions(+), 18 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 94de018..0138b0c 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -818,24 +818,19 @@ static int arch_timer_starting_cpu(unsigned int cpu)
 	return 0;
 }
 
-static void
-arch_timer_detect_rate(void __iomem *cntbase, struct device_node *np)
+/*
+ * For historical reasons, when probing with DT we use whichever (non-zero)
+ * rate was probed first, and don't verify that others match. If the first node
+ * probed has a clock-frequency property, this overrides the HW register.
+ */
+static void arch_timer_of_configure_rate(u32 rate, struct device_node *np)
 {
 	/* Who has more than one independent system counter? */
 	if (arch_timer_rate)
 		return;
 
-	/*
-	 * Try to determine the frequency from the device tree or CNTFRQ,
-	 * if ACPI is enabled, get the frequency from CNTFRQ ONLY.
-	 */
-	if (!acpi_disabled ||
-	    of_property_read_u32(np, "clock-frequency", &arch_timer_rate)) {
-		if (cntbase)
-			arch_timer_rate = readl_relaxed(cntbase + CNTFRQ);
-		else
-			arch_timer_rate = arch_timer_get_cntfrq();
-	}
+	if (of_property_read_u32(np, "clock-frequency", &arch_timer_rate))
+		arch_timer_rate = rate;
 
 	/* Check the timer frequency. */
 	if (arch_timer_rate == 0)
@@ -1166,6 +1161,7 @@ static int __init arch_timer_init(void)
 static int __init arch_timer_of_init(struct device_node *np)
 {
 	int i;
+	u32 rate;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
 		pr_warn("multiple nodes in dt, skipping\n");
@@ -1176,7 +1172,8 @@ static int __init arch_timer_of_init(struct device_node *np)
 	for (i = ARCH_TIMER_PHYS_SECURE_PPI; i < ARCH_TIMER_MAX_TIMER_PPI; i++)
 		arch_timer_ppi[i] = irq_of_parse_and_map(np, i);
 
-	arch_timer_detect_rate(NULL, np);
+	rate = arch_timer_get_cntfrq();
+	arch_timer_of_configure_rate(rate, np);
 
 	arch_timer_c3stop = !of_property_read_bool(np, "always-on");
 
@@ -1212,7 +1209,7 @@ static int __init arch_timer_mem_init(struct device_node *np)
 	struct device_node *frame, *best_frame = NULL;
 	void __iomem *cntctlbase, *base;
 	unsigned int irq, ret = -EINVAL;
-	u32 cnttidr;
+	u32 cnttidr, rate;
 
 	arch_timers_present |= ARCH_TIMER_TYPE_MEM;
 	cntctlbase = of_iomap(np, 0);
@@ -1278,7 +1275,8 @@ static int __init arch_timer_mem_init(struct device_node *np)
 		goto out;
 	}
 
-	arch_timer_detect_rate(base, np);
+	rate = readl(base + CNTFRQ);
+	arch_timer_of_configure_rate(rate, np);
 	ret = arch_timer_mem_register(base, irq);
 	if (ret)
 		goto out;
@@ -1339,8 +1337,15 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 		map_generic_timer_interrupt(gtdt->non_secure_el2_interrupt,
 		gtdt->non_secure_el2_flags);
 
-	/* Get the frequency from CNTFRQ */
-	arch_timer_detect_rate(NULL, NULL);
+	/*
+	 * When probing via ACPI, we have no mechanism to override the sysreg
+	 * CNTFRQ value. This *must* be correct.
+	 */
+	arch_timer_rate = arch_timer_get_cntfrq();
+	if (!arch_timer_rate) {
+		pr_err(FW_BUG "frequency not available.\n");
+		return -EINVAL;
+	}
 
 	arch_timer_uses_ppi = arch_timer_select_ppi();
 	if (!arch_timer_ppi[arch_timer_uses_ppi]) {
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 02/11] clocksource: arm_arch_timer: refactor arch_timer_needs_probing
  2017-04-14 18:40 ` fu.wei at linaro.org
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

When booting with DT, it's possible for timer nodes to be probed in any
order. Some common initialisation needs to occur after all nodes have
been probed, and arch_timer_common_init() has code to detect when this
has happened.

This logic is DT-specific, and it would be best to factor it out of the
common code that will be shared with ACPI.

This patch folds this into the existing arch_timer_needs_probing(),
which is renamed to arch_timer_needs_of_probing(), and no longer takes
any arguments. This is only called when using DT, and not when using
ACPI, which will have a deterministic probe order.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 34 +++++++++++++++++++---------------
 1 file changed, 19 insertions(+), 15 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 0138b0c..03d71d6 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1076,15 +1076,28 @@ static const struct of_device_id arch_timer_mem_of_match[] __initconst = {
 	{},
 };
 
-static bool __init
-arch_timer_needs_probing(int type, const struct of_device_id *matches)
+static bool __init arch_timer_needs_of_probing(void)
 {
 	struct device_node *dn;
 	bool needs_probing = false;
+	unsigned int mask = ARCH_TIMER_TYPE_CP15 | ARCH_TIMER_TYPE_MEM;
 
-	dn = of_find_matching_node(NULL, matches);
-	if (dn && of_device_is_available(dn) && !(arch_timers_present & type))
+	/* We have two timers, and both device-tree nodes are probed. */
+	if ((arch_timers_present & mask) == mask)
+		return false;
+
+	/*
+	 * Only one type of timer is probed,
+	 * check if we have another type of timer node in device-tree.
+	 */
+	if (arch_timers_present & ARCH_TIMER_TYPE_CP15)
+		dn = of_find_matching_node(NULL, arch_timer_mem_of_match);
+	else
+		dn = of_find_matching_node(NULL, arch_timer_of_match);
+
+	if (dn && of_device_is_available(dn))
 		needs_probing = true;
+
 	of_node_put(dn);
 
 	return needs_probing;
@@ -1092,17 +1105,8 @@ arch_timer_needs_probing(int type, const struct of_device_id *matches)
 
 static int __init arch_timer_common_init(void)
 {
-	unsigned mask = ARCH_TIMER_TYPE_CP15 | ARCH_TIMER_TYPE_MEM;
-
-	/* Wait until both nodes are probed if we have two timers */
-	if ((arch_timers_present & mask) != mask) {
-		if (arch_timer_needs_probing(ARCH_TIMER_TYPE_MEM,
-					     arch_timer_mem_of_match))
-			return 0;
-		if (arch_timer_needs_probing(ARCH_TIMER_TYPE_CP15,
-					     arch_timer_of_match))
-			return 0;
-	}
+	if (acpi_disabled && arch_timer_needs_of_probing())
+		return 0;
 
 	arch_timer_banner(arch_timers_present);
 	arch_counter_register(arch_timers_present);
-- 
2.9.3


^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 02/11] clocksource: arm_arch_timer: refactor arch_timer_needs_probing
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

When booting with DT, it's possible for timer nodes to be probed in any
order. Some common initialisation needs to occur after all nodes have
been probed, and arch_timer_common_init() has code to detect when this
has happened.

This logic is DT-specific, and it would be best to factor it out of the
common code that will be shared with ACPI.

This patch folds this into the existing arch_timer_needs_probing(),
which is renamed to arch_timer_needs_of_probing(), and no longer takes
any arguments. This is only called when using DT, and not when using
ACPI, which will have a deterministic probe order.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 34 +++++++++++++++++++---------------
 1 file changed, 19 insertions(+), 15 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 0138b0c..03d71d6 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1076,15 +1076,28 @@ static const struct of_device_id arch_timer_mem_of_match[] __initconst = {
 	{},
 };
 
-static bool __init
-arch_timer_needs_probing(int type, const struct of_device_id *matches)
+static bool __init arch_timer_needs_of_probing(void)
 {
 	struct device_node *dn;
 	bool needs_probing = false;
+	unsigned int mask = ARCH_TIMER_TYPE_CP15 | ARCH_TIMER_TYPE_MEM;
 
-	dn = of_find_matching_node(NULL, matches);
-	if (dn && of_device_is_available(dn) && !(arch_timers_present & type))
+	/* We have two timers, and both device-tree nodes are probed. */
+	if ((arch_timers_present & mask) == mask)
+		return false;
+
+	/*
+	 * Only one type of timer is probed,
+	 * check if we have another type of timer node in device-tree.
+	 */
+	if (arch_timers_present & ARCH_TIMER_TYPE_CP15)
+		dn = of_find_matching_node(NULL, arch_timer_mem_of_match);
+	else
+		dn = of_find_matching_node(NULL, arch_timer_of_match);
+
+	if (dn && of_device_is_available(dn))
 		needs_probing = true;
+
 	of_node_put(dn);
 
 	return needs_probing;
@@ -1092,17 +1105,8 @@ arch_timer_needs_probing(int type, const struct of_device_id *matches)
 
 static int __init arch_timer_common_init(void)
 {
-	unsigned mask = ARCH_TIMER_TYPE_CP15 | ARCH_TIMER_TYPE_MEM;
-
-	/* Wait until both nodes are probed if we have two timers */
-	if ((arch_timers_present & mask) != mask) {
-		if (arch_timer_needs_probing(ARCH_TIMER_TYPE_MEM,
-					     arch_timer_mem_of_match))
-			return 0;
-		if (arch_timer_needs_probing(ARCH_TIMER_TYPE_CP15,
-					     arch_timer_of_match))
-			return 0;
-	}
+	if (acpi_disabled && arch_timer_needs_of_probing())
+		return 0;
 
 	arch_timer_banner(arch_timers_present);
 	arch_counter_register(arch_timers_present);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 03/11] clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
  2017-04-14 18:40 ` fu.wei at linaro.org
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

To cleanly split code paths specific to ACPI or DT at a higher level,
this patch removes arch_timer_init(), folding the relevant
parts of its logic into existing callers.

This paths the way for further rework, and saves a few lines.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 46 ++++++++++++++++--------------------
 1 file changed, 21 insertions(+), 25 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 03d71d6..e5e8708 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1105,9 +1105,6 @@ static bool __init arch_timer_needs_of_probing(void)
 
 static int __init arch_timer_common_init(void)
 {
-	if (acpi_disabled && arch_timer_needs_of_probing())
-		return 0;
-
 	arch_timer_banner(arch_timers_present);
 	arch_counter_register(arch_timers_present);
 	return arch_timer_arch_init();
@@ -1145,26 +1142,9 @@ static enum arch_timer_ppi_nr __init arch_timer_select_ppi(void)
 	return ARCH_TIMER_PHYS_SECURE_PPI;
 }
 
-static int __init arch_timer_init(void)
-{
-	int ret;
-
-	ret = arch_timer_register();
-	if (ret)
-		return ret;
-
-	ret = arch_timer_common_init();
-	if (ret)
-		return ret;
-
-	arch_timer_kvm_info.virtual_irq = arch_timer_ppi[ARCH_TIMER_VIRT_PPI];
-
-	return 0;
-}
-
 static int __init arch_timer_of_init(struct device_node *np)
 {
-	int i;
+	int i, ret;
 	u32 rate;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
@@ -1176,6 +1156,8 @@ static int __init arch_timer_of_init(struct device_node *np)
 	for (i = ARCH_TIMER_PHYS_SECURE_PPI; i < ARCH_TIMER_MAX_TIMER_PPI; i++)
 		arch_timer_ppi[i] = irq_of_parse_and_map(np, i);
 
+	arch_timer_kvm_info.virtual_irq = arch_timer_ppi[ARCH_TIMER_VIRT_PPI];
+
 	rate = arch_timer_get_cntfrq();
 	arch_timer_of_configure_rate(rate, np);
 
@@ -1203,7 +1185,14 @@ static int __init arch_timer_of_init(struct device_node *np)
 	arch_counter_suspend_stop = of_property_read_bool(np,
 							 "arm,no-tick-in-suspend");
 
-	return arch_timer_init();
+	ret = arch_timer_register();
+	if (ret)
+		return ret;
+
+	if (arch_timer_needs_of_probing())
+		return 0;
+
+	return arch_timer_common_init();
 }
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
 CLOCKSOURCE_OF_DECLARE(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
@@ -1285,7 +1274,8 @@ static int __init arch_timer_mem_init(struct device_node *np)
 	if (ret)
 		goto out;
 
-	return arch_timer_common_init();
+	if (!arch_timer_needs_of_probing())
+		ret = arch_timer_common_init();
 out:
 	iounmap(cntctlbase);
 	of_node_put(best_frame);
@@ -1314,6 +1304,7 @@ static int __init map_generic_timer_interrupt(u32 interrupt, u32 flags)
 /* Initialize per-processor generic timer */
 static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 {
+	int ret;
 	struct acpi_table_gtdt *gtdt;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
@@ -1341,6 +1332,8 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 		map_generic_timer_interrupt(gtdt->non_secure_el2_interrupt,
 		gtdt->non_secure_el2_flags);
 
+	arch_timer_kvm_info.virtual_irq = arch_timer_ppi[ARCH_TIMER_VIRT_PPI];
+
 	/*
 	 * When probing via ACPI, we have no mechanism to override the sysreg
 	 * CNTFRQ value. This *must* be correct.
@@ -1363,8 +1356,11 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 	/* Check for globally applicable workarounds */
 	arch_timer_check_ool_workaround(ate_match_acpi_oem_info, table);
 
-	arch_timer_init();
-	return 0;
+	ret = arch_timer_register();
+	if (ret)
+		return ret;
+
+	return arch_timer_common_init();
 }
 CLOCKSOURCE_ACPI_DECLARE(arch_timer, ACPI_SIG_GTDT, arch_timer_acpi_init);
 #endif
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 03/11] clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

To cleanly split code paths specific to ACPI or DT at a higher level,
this patch removes arch_timer_init(), folding the relevant
parts of its logic into existing callers.

This paths the way for further rework, and saves a few lines.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 46 ++++++++++++++++--------------------
 1 file changed, 21 insertions(+), 25 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 03d71d6..e5e8708 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1105,9 +1105,6 @@ static bool __init arch_timer_needs_of_probing(void)
 
 static int __init arch_timer_common_init(void)
 {
-	if (acpi_disabled && arch_timer_needs_of_probing())
-		return 0;
-
 	arch_timer_banner(arch_timers_present);
 	arch_counter_register(arch_timers_present);
 	return arch_timer_arch_init();
@@ -1145,26 +1142,9 @@ static enum arch_timer_ppi_nr __init arch_timer_select_ppi(void)
 	return ARCH_TIMER_PHYS_SECURE_PPI;
 }
 
-static int __init arch_timer_init(void)
-{
-	int ret;
-
-	ret = arch_timer_register();
-	if (ret)
-		return ret;
-
-	ret = arch_timer_common_init();
-	if (ret)
-		return ret;
-
-	arch_timer_kvm_info.virtual_irq = arch_timer_ppi[ARCH_TIMER_VIRT_PPI];
-
-	return 0;
-}
-
 static int __init arch_timer_of_init(struct device_node *np)
 {
-	int i;
+	int i, ret;
 	u32 rate;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
@@ -1176,6 +1156,8 @@ static int __init arch_timer_of_init(struct device_node *np)
 	for (i = ARCH_TIMER_PHYS_SECURE_PPI; i < ARCH_TIMER_MAX_TIMER_PPI; i++)
 		arch_timer_ppi[i] = irq_of_parse_and_map(np, i);
 
+	arch_timer_kvm_info.virtual_irq = arch_timer_ppi[ARCH_TIMER_VIRT_PPI];
+
 	rate = arch_timer_get_cntfrq();
 	arch_timer_of_configure_rate(rate, np);
 
@@ -1203,7 +1185,14 @@ static int __init arch_timer_of_init(struct device_node *np)
 	arch_counter_suspend_stop = of_property_read_bool(np,
 							 "arm,no-tick-in-suspend");
 
-	return arch_timer_init();
+	ret = arch_timer_register();
+	if (ret)
+		return ret;
+
+	if (arch_timer_needs_of_probing())
+		return 0;
+
+	return arch_timer_common_init();
 }
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
 CLOCKSOURCE_OF_DECLARE(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
@@ -1285,7 +1274,8 @@ static int __init arch_timer_mem_init(struct device_node *np)
 	if (ret)
 		goto out;
 
-	return arch_timer_common_init();
+	if (!arch_timer_needs_of_probing())
+		ret = arch_timer_common_init();
 out:
 	iounmap(cntctlbase);
 	of_node_put(best_frame);
@@ -1314,6 +1304,7 @@ static int __init map_generic_timer_interrupt(u32 interrupt, u32 flags)
 /* Initialize per-processor generic timer */
 static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 {
+	int ret;
 	struct acpi_table_gtdt *gtdt;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
@@ -1341,6 +1332,8 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 		map_generic_timer_interrupt(gtdt->non_secure_el2_interrupt,
 		gtdt->non_secure_el2_flags);
 
+	arch_timer_kvm_info.virtual_irq = arch_timer_ppi[ARCH_TIMER_VIRT_PPI];
+
 	/*
 	 * When probing via ACPI, we have no mechanism to override the sysreg
 	 * CNTFRQ value. This *must* be correct.
@@ -1363,8 +1356,11 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 	/* Check for globally applicable workarounds */
 	arch_timer_check_ool_workaround(ate_match_acpi_oem_info, table);
 
-	arch_timer_init();
-	return 0;
+	ret = arch_timer_register();
+	if (ret)
+		return ret;
+
+	return arch_timer_common_init();
 }
 CLOCKSOURCE_ACPI_DECLARE(arch_timer, ACPI_SIG_GTDT, arch_timer_acpi_init);
 #endif
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 04/11] clocksource: arm_arch_timer: add structs to describe MMIO timer
  2017-04-14 18:40 ` fu.wei at linaro.org
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

In preparation for ACPI GTDT support, this patch adds structs to
describe the MMIO timers indepedent of the firmware interface.

Subsequent patches will use these to split the FW/HW probing logic, so
that the HW probing logic can be shared by ACPI and DT.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 include/clocksource/arm_arch_timer.h | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/include/clocksource/arm_arch_timer.h b/include/clocksource/arm_arch_timer.h
index 4a98c06..cc805b7 100644
--- a/include/clocksource/arm_arch_timer.h
+++ b/include/clocksource/arm_arch_timer.h
@@ -57,6 +57,8 @@ enum arch_timer_spi_nr {
 #define ARCH_TIMER_MEM_PHYS_ACCESS	2
 #define ARCH_TIMER_MEM_VIRT_ACCESS	3
 
+#define ARCH_TIMER_MEM_MAX_FRAMES	8
+
 #define ARCH_TIMER_USR_PCT_ACCESS_EN	(1 << 0) /* physical counter */
 #define ARCH_TIMER_USR_VCT_ACCESS_EN	(1 << 1) /* virtual counter */
 #define ARCH_TIMER_VIRT_EVT_EN		(1 << 2)
@@ -72,6 +74,20 @@ struct arch_timer_kvm_info {
 	int virtual_irq;
 };
 
+struct arch_timer_mem_frame {
+	bool valid;
+	phys_addr_t cntbase;
+	size_t size;
+	int phys_irq;
+	int virt_irq;
+};
+
+struct arch_timer_mem {
+	phys_addr_t cntctlbase;
+	size_t size;
+	struct arch_timer_mem_frame frame[ARCH_TIMER_MEM_MAX_FRAMES];
+};
+
 #ifdef CONFIG_ARM_ARCH_TIMER
 
 extern u32 arch_timer_get_rate(void);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 04/11] clocksource: arm_arch_timer: add structs to describe MMIO timer
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

In preparation for ACPI GTDT support, this patch adds structs to
describe the MMIO timers indepedent of the firmware interface.

Subsequent patches will use these to split the FW/HW probing logic, so
that the HW probing logic can be shared by ACPI and DT.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 include/clocksource/arm_arch_timer.h | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/include/clocksource/arm_arch_timer.h b/include/clocksource/arm_arch_timer.h
index 4a98c06..cc805b7 100644
--- a/include/clocksource/arm_arch_timer.h
+++ b/include/clocksource/arm_arch_timer.h
@@ -57,6 +57,8 @@ enum arch_timer_spi_nr {
 #define ARCH_TIMER_MEM_PHYS_ACCESS	2
 #define ARCH_TIMER_MEM_VIRT_ACCESS	3
 
+#define ARCH_TIMER_MEM_MAX_FRAMES	8
+
 #define ARCH_TIMER_USR_PCT_ACCESS_EN	(1 << 0) /* physical counter */
 #define ARCH_TIMER_USR_VCT_ACCESS_EN	(1 << 1) /* virtual counter */
 #define ARCH_TIMER_VIRT_EVT_EN		(1 << 2)
@@ -72,6 +74,20 @@ struct arch_timer_kvm_info {
 	int virtual_irq;
 };
 
+struct arch_timer_mem_frame {
+	bool valid;
+	phys_addr_t cntbase;
+	size_t size;
+	int phys_irq;
+	int virt_irq;
+};
+
+struct arch_timer_mem {
+	phys_addr_t cntctlbase;
+	size_t size;
+	struct arch_timer_mem_frame frame[ARCH_TIMER_MEM_MAX_FRAMES];
+};
+
 #ifdef CONFIG_ARM_ARCH_TIMER
 
 extern u32 arch_timer_get_rate(void);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 05/11] clocksource: arm_arch_timer: split MMIO timer probing.
  2017-04-14 18:40 ` fu.wei at linaro.org
  (?)
@ 2017-04-14 18:40     ` fu.wei
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei-QSEj5FYQhm4dnm+yROfE0A @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw-LthD3rsA81gm4RdzfppkhA, lenb-DgEjT+Ai2ygdnm+yROfE0A,
	daniel.lezcano-QSEj5FYQhm4dnm+yROfE0A,
	tglx-hfZtesqFncYOwBW4kG4KsQ, marc.zyngier-5wv7dgnIgG8,
	mark.rutland-5wv7dgnIgG8, lorenzo.pieralisi-5wv7dgnIgG8,
	sudeep.holla-5wv7dgnIgG8, hanjun.guo-QSEj5FYQhm4dnm+yROfE0A
  Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	linaro-acpi-cunTk1MwBs8s++Sfvej+rw,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA,
	linux-acpi-u79uwXL29TY76Z2rM5mHXA,
	rruigrok-sgV2jX0FEOL9JmXXK+q4OQ, harba-sgV2jX0FEOL9JmXXK+q4OQ,
	cov-sgV2jX0FEOL9JmXXK+q4OQ, timur-sgV2jX0FEOL9JmXXK+q4OQ,
	graeme.gregory-QSEj5FYQhm4dnm+yROfE0A,
	al.stone-QSEj5FYQhm4dnm+yROfE0A, jcm-H+wXaHxf7aLQT0dZR+AlfA,
	wei-H+wXaHxf7aLQT0dZR+AlfA, arnd-r2nGTMty4D4,
	catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8,
	Suravee.Suthikulpanit-5C7GfCeVMHo, leo.duran-5C7GfCeVMHo,
	wim-IQzOog9fTRqzQB+pC5nmwQ, linux-0h96xk9xTtrk1uMJSBkQmQ,
	linux-watchdog-u79uwXL29TY76Z2rM5mHXA, tn-nYOzD4b6Jr9Wk0Htik3J/w,
	christoffer.dall-QSEj5FYQhm4dnm+yROfE0A,
	julien.grall-5wv7dgnIgG8, Fu Wei

From: Fu Wei <fu.wei-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>

Currently the code to probe MMIO architected timers mixes DT parsing with
actual poking of hardware. This makes the code harder than necessary to
understand, and makes it difficult to add support for probing via ACPI.

This patch splits the DT parsing from HW probing. The DT parsing now
lives in arch_timer_mem_of_init(), which fills in an arch_timer_mem
structure that it hands to probing functions that can be reused for ACPI
support.

Since the rate detection logic will be slight different when using ACPI,
the probing is performed as a number of steps. This results in more code
for the moment, and some arguably redundant work, but simplifies matters
considerably when ACPI support is added.

Signed-off-by: Fu Wei <fu.wei-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
[Mark: refactor the probing split]
Signed-off-by: Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>
---
 drivers/clocksource/arm_arch_timer.c | 186 +++++++++++++++++++++++++++--------
 1 file changed, 143 insertions(+), 43 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index e5e8708..dad0264 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1197,18 +1197,37 @@ static int __init arch_timer_of_init(struct device_node *np)
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
 CLOCKSOURCE_OF_DECLARE(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
 
-static int __init arch_timer_mem_init(struct device_node *np)
+static u32 __init
+arch_timer_mem_frame_get_cntfrq(struct arch_timer_mem_frame *frame)
 {
-	struct device_node *frame, *best_frame = NULL;
-	void __iomem *cntctlbase, *base;
-	unsigned int irq, ret = -EINVAL;
-	u32 cnttidr, rate;
+	void __iomem *base;
+	u32 rate;
 
-	arch_timers_present |= ARCH_TIMER_TYPE_MEM;
-	cntctlbase = of_iomap(np, 0);
+	base = ioremap(frame->cntbase, frame->size);
+	if (!base) {
+		pr_err("Unable to map frame @ %pa\n", &frame->cntbase);
+		return 0;
+	}
+
+	rate = readl_relaxed(frame + CNTFRQ);
+
+	iounmap(frame);
+
+	return rate;
+}
+
+static struct arch_timer_mem_frame * __init
+arch_timer_mem_find_best_frame(struct arch_timer_mem *timer_mem)
+{
+	struct arch_timer_mem_frame *frame, *best_frame = NULL;
+	void __iomem *cntctlbase;
+	u32 cnttidr;
+	int i;
+
+	cntctlbase = ioremap(timer_mem->cntctlbase, timer_mem->size);
 	if (!cntctlbase) {
-		pr_err("Can't find CNTCTLBase\n");
-		return -ENXIO;
+		pr_err("Can't map CNTCTLBase @ %pa\n", &timer_mem->cntctlbase);
+		return NULL;
 	}
 
 	cnttidr = readl_relaxed(cntctlbase + CNTTIDR);
@@ -1217,25 +1236,20 @@ static int __init arch_timer_mem_init(struct device_node *np)
 	 * Try to find a virtual capable frame. Otherwise fall back to a
 	 * physical capable frame.
 	 */
-	for_each_available_child_of_node(np, frame) {
-		int n;
-		u32 cntacr;
+	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
+		u32 cntacr = CNTACR_RFRQ | CNTACR_RWPT | CNTACR_RPCT |
+			     CNTACR_RWVT | CNTACR_RVOFF | CNTACR_RVCT;
 
-		if (of_property_read_u32(frame, "frame-number", &n)) {
-			pr_err("Missing frame-number\n");
-			of_node_put(frame);
-			goto out;
-		}
+		frame = &timer_mem->frame[i];
+		if (!frame->valid)
+			continue;
 
 		/* Try enabling everything, and see what sticks */
-		cntacr = CNTACR_RFRQ | CNTACR_RWPT | CNTACR_RPCT |
-			 CNTACR_RWVT | CNTACR_RVOFF | CNTACR_RVCT;
-		writel_relaxed(cntacr, cntctlbase + CNTACR(n));
-		cntacr = readl_relaxed(cntctlbase + CNTACR(n));
+		writel_relaxed(cntacr, cntctlbase + CNTACR(i));
+		cntacr = readl_relaxed(cntctlbase + CNTACR(i));
 
-		if ((cnttidr & CNTTIDR_VIRT(n)) &&
+		if ((cnttidr & CNTTIDR_VIRT(i)) &&
 		    !(~cntacr & (CNTACR_RWVT | CNTACR_RVCT))) {
-			of_node_put(best_frame);
 			best_frame = frame;
 			arch_timer_mem_use_virtual = true;
 			break;
@@ -1244,45 +1258,131 @@ static int __init arch_timer_mem_init(struct device_node *np)
 		if (~cntacr & (CNTACR_RWPT | CNTACR_RPCT))
 			continue;
 
-		of_node_put(best_frame);
-		best_frame = of_node_get(frame);
+		best_frame = frame;
 	}
 
-	ret= -ENXIO;
-	base = arch_counter_base = of_io_request_and_map(best_frame, 0,
-							 "arch_mem_timer");
-	if (IS_ERR(base)) {
-		pr_err("Can't map frame's registers\n");
-		goto out;
-	}
+	iounmap(cntctlbase);
+
+	if (!best_frame)
+		pr_err("Unable to find a suitable frame in timer @ %pa\n",
+		       &timer_mem->cntctlbase);
+
+	return frame;
+}
+
+static int __init
+arch_timer_mem_frame_register(struct arch_timer_mem_frame *frame)
+{
+	void __iomem *base;
+	int ret, irq = 0;
 
 	if (arch_timer_mem_use_virtual)
-		irq = irq_of_parse_and_map(best_frame, ARCH_TIMER_VIRT_SPI);
+		irq = frame->virt_irq;
 	else
-		irq = irq_of_parse_and_map(best_frame, ARCH_TIMER_PHYS_SPI);
+		irq = frame->phys_irq;
 
-	ret = -EINVAL;
 	if (!irq) {
 		pr_err("Frame missing %s irq.\n",
 		       arch_timer_mem_use_virtual ? "virt" : "phys");
-		goto out;
+		return -EINVAL;
+	}
+
+	if (!request_mem_region(frame->cntbase, frame->size,
+				"arch_mem_timer"))
+		return -EBUSY;
+
+	base = ioremap(frame->cntbase, frame->size);
+	if (!base) {
+		pr_err("Can't map frame's registers\n");
+		return -ENXIO;
 	}
 
-	rate = readl(base + CNTFRQ);
-	arch_timer_of_configure_rate(rate, np);
 	ret = arch_timer_mem_register(base, irq);
-	if (ret)
+	if (ret) {
+		iounmap(base);
+		return ret;
+	}
+
+	arch_counter_base = base;
+	arch_timers_present |= ARCH_TIMER_TYPE_MEM;
+
+	return 0;
+}
+
+static int __init arch_timer_mem_of_init(struct device_node *np)
+{
+	struct arch_timer_mem *timer_mem;
+	struct arch_timer_mem_frame *frame;
+	struct device_node *frame_node;
+	struct resource res;
+	int ret = -EINVAL;
+	u32 rate;
+
+	timer_mem = kzalloc(sizeof(*timer_mem), GFP_KERNEL);
+	if (!timer_mem)
+		return -ENOMEM;
+
+	if (of_address_to_resource(np, 0, &res))
 		goto out;
+	timer_mem->cntctlbase = res.start;
+	timer_mem->size = resource_size(&res);
 
-	if (!arch_timer_needs_of_probing())
+	for_each_available_child_of_node(np, frame_node) {
+		u32 n;
+		struct arch_timer_mem_frame *frame;
+
+		if (of_property_read_u32(frame_node, "frame-number", &n)) {
+			pr_err(FW_BUG "Missing frame-number.\n");
+			of_node_put(frame_node);
+			goto out;
+		}
+		if (n >= ARCH_TIMER_MEM_MAX_FRAMES) {
+			pr_err(FW_BUG "Wrong frame-number, only 0-%u are permitted.\n",
+			       ARCH_TIMER_MEM_MAX_FRAMES - 1);
+			of_node_put(frame_node);
+			goto out;
+		}
+		frame = &timer_mem->frame[n];
+
+		if (frame->valid) {
+			pr_err(FW_BUG "Duplicated frame-number.\n");
+			of_node_put(frame_node);
+			goto out;
+		}
+
+		if (of_address_to_resource(frame_node, 0, &res)) {
+			of_node_put(frame_node);
+			goto out;
+		}
+		frame->cntbase = res.start;
+		frame->size = resource_size(&res);
+
+		frame->virt_irq = irq_of_parse_and_map(frame_node,
+						       ARCH_TIMER_VIRT_SPI);
+		frame->phys_irq = irq_of_parse_and_map(frame_node,
+						       ARCH_TIMER_PHYS_SPI);
+
+		frame->valid = true;
+	}
+
+	frame = arch_timer_mem_find_best_frame(timer_mem);
+	if (!frame) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	rate = arch_timer_mem_frame_get_cntfrq(frame);
+	arch_timer_of_configure_rate(rate, np);
+
+	ret = arch_timer_mem_frame_register(frame);
+	if (!ret && !arch_timer_needs_of_probing())
 		ret = arch_timer_common_init();
 out:
-	iounmap(cntctlbase);
-	of_node_put(best_frame);
+	kfree(timer_mem);
 	return ret;
 }
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
-		       arch_timer_mem_init);
+		       arch_timer_mem_of_init);
 
 #ifdef CONFIG_ACPI
 static int __init map_generic_timer_interrupt(u32 interrupt, u32 flags)
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 05/11] clocksource: arm_arch_timer: split MMIO timer probing.
@ 2017-04-14 18:40     ` fu.wei
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

Currently the code to probe MMIO architected timers mixes DT parsing with
actual poking of hardware. This makes the code harder than necessary to
understand, and makes it difficult to add support for probing via ACPI.

This patch splits the DT parsing from HW probing. The DT parsing now
lives in arch_timer_mem_of_init(), which fills in an arch_timer_mem
structure that it hands to probing functions that can be reused for ACPI
support.

Since the rate detection logic will be slight different when using ACPI,
the probing is performed as a number of steps. This results in more code
for the moment, and some arguably redundant work, but simplifies matters
considerably when ACPI support is added.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
[Mark: refactor the probing split]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 186 +++++++++++++++++++++++++++--------
 1 file changed, 143 insertions(+), 43 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index e5e8708..dad0264 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1197,18 +1197,37 @@ static int __init arch_timer_of_init(struct device_node *np)
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
 CLOCKSOURCE_OF_DECLARE(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
 
-static int __init arch_timer_mem_init(struct device_node *np)
+static u32 __init
+arch_timer_mem_frame_get_cntfrq(struct arch_timer_mem_frame *frame)
 {
-	struct device_node *frame, *best_frame = NULL;
-	void __iomem *cntctlbase, *base;
-	unsigned int irq, ret = -EINVAL;
-	u32 cnttidr, rate;
+	void __iomem *base;
+	u32 rate;
 
-	arch_timers_present |= ARCH_TIMER_TYPE_MEM;
-	cntctlbase = of_iomap(np, 0);
+	base = ioremap(frame->cntbase, frame->size);
+	if (!base) {
+		pr_err("Unable to map frame @ %pa\n", &frame->cntbase);
+		return 0;
+	}
+
+	rate = readl_relaxed(frame + CNTFRQ);
+
+	iounmap(frame);
+
+	return rate;
+}
+
+static struct arch_timer_mem_frame * __init
+arch_timer_mem_find_best_frame(struct arch_timer_mem *timer_mem)
+{
+	struct arch_timer_mem_frame *frame, *best_frame = NULL;
+	void __iomem *cntctlbase;
+	u32 cnttidr;
+	int i;
+
+	cntctlbase = ioremap(timer_mem->cntctlbase, timer_mem->size);
 	if (!cntctlbase) {
-		pr_err("Can't find CNTCTLBase\n");
-		return -ENXIO;
+		pr_err("Can't map CNTCTLBase @ %pa\n", &timer_mem->cntctlbase);
+		return NULL;
 	}
 
 	cnttidr = readl_relaxed(cntctlbase + CNTTIDR);
@@ -1217,25 +1236,20 @@ static int __init arch_timer_mem_init(struct device_node *np)
 	 * Try to find a virtual capable frame. Otherwise fall back to a
 	 * physical capable frame.
 	 */
-	for_each_available_child_of_node(np, frame) {
-		int n;
-		u32 cntacr;
+	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
+		u32 cntacr = CNTACR_RFRQ | CNTACR_RWPT | CNTACR_RPCT |
+			     CNTACR_RWVT | CNTACR_RVOFF | CNTACR_RVCT;
 
-		if (of_property_read_u32(frame, "frame-number", &n)) {
-			pr_err("Missing frame-number\n");
-			of_node_put(frame);
-			goto out;
-		}
+		frame = &timer_mem->frame[i];
+		if (!frame->valid)
+			continue;
 
 		/* Try enabling everything, and see what sticks */
-		cntacr = CNTACR_RFRQ | CNTACR_RWPT | CNTACR_RPCT |
-			 CNTACR_RWVT | CNTACR_RVOFF | CNTACR_RVCT;
-		writel_relaxed(cntacr, cntctlbase + CNTACR(n));
-		cntacr = readl_relaxed(cntctlbase + CNTACR(n));
+		writel_relaxed(cntacr, cntctlbase + CNTACR(i));
+		cntacr = readl_relaxed(cntctlbase + CNTACR(i));
 
-		if ((cnttidr & CNTTIDR_VIRT(n)) &&
+		if ((cnttidr & CNTTIDR_VIRT(i)) &&
 		    !(~cntacr & (CNTACR_RWVT | CNTACR_RVCT))) {
-			of_node_put(best_frame);
 			best_frame = frame;
 			arch_timer_mem_use_virtual = true;
 			break;
@@ -1244,45 +1258,131 @@ static int __init arch_timer_mem_init(struct device_node *np)
 		if (~cntacr & (CNTACR_RWPT | CNTACR_RPCT))
 			continue;
 
-		of_node_put(best_frame);
-		best_frame = of_node_get(frame);
+		best_frame = frame;
 	}
 
-	ret= -ENXIO;
-	base = arch_counter_base = of_io_request_and_map(best_frame, 0,
-							 "arch_mem_timer");
-	if (IS_ERR(base)) {
-		pr_err("Can't map frame's registers\n");
-		goto out;
-	}
+	iounmap(cntctlbase);
+
+	if (!best_frame)
+		pr_err("Unable to find a suitable frame in timer @ %pa\n",
+		       &timer_mem->cntctlbase);
+
+	return frame;
+}
+
+static int __init
+arch_timer_mem_frame_register(struct arch_timer_mem_frame *frame)
+{
+	void __iomem *base;
+	int ret, irq = 0;
 
 	if (arch_timer_mem_use_virtual)
-		irq = irq_of_parse_and_map(best_frame, ARCH_TIMER_VIRT_SPI);
+		irq = frame->virt_irq;
 	else
-		irq = irq_of_parse_and_map(best_frame, ARCH_TIMER_PHYS_SPI);
+		irq = frame->phys_irq;
 
-	ret = -EINVAL;
 	if (!irq) {
 		pr_err("Frame missing %s irq.\n",
 		       arch_timer_mem_use_virtual ? "virt" : "phys");
-		goto out;
+		return -EINVAL;
+	}
+
+	if (!request_mem_region(frame->cntbase, frame->size,
+				"arch_mem_timer"))
+		return -EBUSY;
+
+	base = ioremap(frame->cntbase, frame->size);
+	if (!base) {
+		pr_err("Can't map frame's registers\n");
+		return -ENXIO;
 	}
 
-	rate = readl(base + CNTFRQ);
-	arch_timer_of_configure_rate(rate, np);
 	ret = arch_timer_mem_register(base, irq);
-	if (ret)
+	if (ret) {
+		iounmap(base);
+		return ret;
+	}
+
+	arch_counter_base = base;
+	arch_timers_present |= ARCH_TIMER_TYPE_MEM;
+
+	return 0;
+}
+
+static int __init arch_timer_mem_of_init(struct device_node *np)
+{
+	struct arch_timer_mem *timer_mem;
+	struct arch_timer_mem_frame *frame;
+	struct device_node *frame_node;
+	struct resource res;
+	int ret = -EINVAL;
+	u32 rate;
+
+	timer_mem = kzalloc(sizeof(*timer_mem), GFP_KERNEL);
+	if (!timer_mem)
+		return -ENOMEM;
+
+	if (of_address_to_resource(np, 0, &res))
 		goto out;
+	timer_mem->cntctlbase = res.start;
+	timer_mem->size = resource_size(&res);
 
-	if (!arch_timer_needs_of_probing())
+	for_each_available_child_of_node(np, frame_node) {
+		u32 n;
+		struct arch_timer_mem_frame *frame;
+
+		if (of_property_read_u32(frame_node, "frame-number", &n)) {
+			pr_err(FW_BUG "Missing frame-number.\n");
+			of_node_put(frame_node);
+			goto out;
+		}
+		if (n >= ARCH_TIMER_MEM_MAX_FRAMES) {
+			pr_err(FW_BUG "Wrong frame-number, only 0-%u are permitted.\n",
+			       ARCH_TIMER_MEM_MAX_FRAMES - 1);
+			of_node_put(frame_node);
+			goto out;
+		}
+		frame = &timer_mem->frame[n];
+
+		if (frame->valid) {
+			pr_err(FW_BUG "Duplicated frame-number.\n");
+			of_node_put(frame_node);
+			goto out;
+		}
+
+		if (of_address_to_resource(frame_node, 0, &res)) {
+			of_node_put(frame_node);
+			goto out;
+		}
+		frame->cntbase = res.start;
+		frame->size = resource_size(&res);
+
+		frame->virt_irq = irq_of_parse_and_map(frame_node,
+						       ARCH_TIMER_VIRT_SPI);
+		frame->phys_irq = irq_of_parse_and_map(frame_node,
+						       ARCH_TIMER_PHYS_SPI);
+
+		frame->valid = true;
+	}
+
+	frame = arch_timer_mem_find_best_frame(timer_mem);
+	if (!frame) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	rate = arch_timer_mem_frame_get_cntfrq(frame);
+	arch_timer_of_configure_rate(rate, np);
+
+	ret = arch_timer_mem_frame_register(frame);
+	if (!ret && !arch_timer_needs_of_probing())
 		ret = arch_timer_common_init();
 out:
-	iounmap(cntctlbase);
-	of_node_put(best_frame);
+	kfree(timer_mem);
 	return ret;
 }
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
-		       arch_timer_mem_init);
+		       arch_timer_mem_of_init);
 
 #ifdef CONFIG_ACPI
 static int __init map_generic_timer_interrupt(u32 interrupt, u32 flags)
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 05/11] clocksource: arm_arch_timer: split MMIO timer probing.
@ 2017-04-14 18:40     ` fu.wei
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

Currently the code to probe MMIO architected timers mixes DT parsing with
actual poking of hardware. This makes the code harder than necessary to
understand, and makes it difficult to add support for probing via ACPI.

This patch splits the DT parsing from HW probing. The DT parsing now
lives in arch_timer_mem_of_init(), which fills in an arch_timer_mem
structure that it hands to probing functions that can be reused for ACPI
support.

Since the rate detection logic will be slight different when using ACPI,
the probing is performed as a number of steps. This results in more code
for the moment, and some arguably redundant work, but simplifies matters
considerably when ACPI support is added.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
[Mark: refactor the probing split]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 186 +++++++++++++++++++++++++++--------
 1 file changed, 143 insertions(+), 43 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index e5e8708..dad0264 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1197,18 +1197,37 @@ static int __init arch_timer_of_init(struct device_node *np)
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer, "arm,armv7-timer", arch_timer_of_init);
 CLOCKSOURCE_OF_DECLARE(armv8_arch_timer, "arm,armv8-timer", arch_timer_of_init);
 
-static int __init arch_timer_mem_init(struct device_node *np)
+static u32 __init
+arch_timer_mem_frame_get_cntfrq(struct arch_timer_mem_frame *frame)
 {
-	struct device_node *frame, *best_frame = NULL;
-	void __iomem *cntctlbase, *base;
-	unsigned int irq, ret = -EINVAL;
-	u32 cnttidr, rate;
+	void __iomem *base;
+	u32 rate;
 
-	arch_timers_present |= ARCH_TIMER_TYPE_MEM;
-	cntctlbase = of_iomap(np, 0);
+	base = ioremap(frame->cntbase, frame->size);
+	if (!base) {
+		pr_err("Unable to map frame @ %pa\n", &frame->cntbase);
+		return 0;
+	}
+
+	rate = readl_relaxed(frame + CNTFRQ);
+
+	iounmap(frame);
+
+	return rate;
+}
+
+static struct arch_timer_mem_frame * __init
+arch_timer_mem_find_best_frame(struct arch_timer_mem *timer_mem)
+{
+	struct arch_timer_mem_frame *frame, *best_frame = NULL;
+	void __iomem *cntctlbase;
+	u32 cnttidr;
+	int i;
+
+	cntctlbase = ioremap(timer_mem->cntctlbase, timer_mem->size);
 	if (!cntctlbase) {
-		pr_err("Can't find CNTCTLBase\n");
-		return -ENXIO;
+		pr_err("Can't map CNTCTLBase @ %pa\n", &timer_mem->cntctlbase);
+		return NULL;
 	}
 
 	cnttidr = readl_relaxed(cntctlbase + CNTTIDR);
@@ -1217,25 +1236,20 @@ static int __init arch_timer_mem_init(struct device_node *np)
 	 * Try to find a virtual capable frame. Otherwise fall back to a
 	 * physical capable frame.
 	 */
-	for_each_available_child_of_node(np, frame) {
-		int n;
-		u32 cntacr;
+	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
+		u32 cntacr = CNTACR_RFRQ | CNTACR_RWPT | CNTACR_RPCT |
+			     CNTACR_RWVT | CNTACR_RVOFF | CNTACR_RVCT;
 
-		if (of_property_read_u32(frame, "frame-number", &n)) {
-			pr_err("Missing frame-number\n");
-			of_node_put(frame);
-			goto out;
-		}
+		frame = &timer_mem->frame[i];
+		if (!frame->valid)
+			continue;
 
 		/* Try enabling everything, and see what sticks */
-		cntacr = CNTACR_RFRQ | CNTACR_RWPT | CNTACR_RPCT |
-			 CNTACR_RWVT | CNTACR_RVOFF | CNTACR_RVCT;
-		writel_relaxed(cntacr, cntctlbase + CNTACR(n));
-		cntacr = readl_relaxed(cntctlbase + CNTACR(n));
+		writel_relaxed(cntacr, cntctlbase + CNTACR(i));
+		cntacr = readl_relaxed(cntctlbase + CNTACR(i));
 
-		if ((cnttidr & CNTTIDR_VIRT(n)) &&
+		if ((cnttidr & CNTTIDR_VIRT(i)) &&
 		    !(~cntacr & (CNTACR_RWVT | CNTACR_RVCT))) {
-			of_node_put(best_frame);
 			best_frame = frame;
 			arch_timer_mem_use_virtual = true;
 			break;
@@ -1244,45 +1258,131 @@ static int __init arch_timer_mem_init(struct device_node *np)
 		if (~cntacr & (CNTACR_RWPT | CNTACR_RPCT))
 			continue;
 
-		of_node_put(best_frame);
-		best_frame = of_node_get(frame);
+		best_frame = frame;
 	}
 
-	ret= -ENXIO;
-	base = arch_counter_base = of_io_request_and_map(best_frame, 0,
-							 "arch_mem_timer");
-	if (IS_ERR(base)) {
-		pr_err("Can't map frame's registers\n");
-		goto out;
-	}
+	iounmap(cntctlbase);
+
+	if (!best_frame)
+		pr_err("Unable to find a suitable frame in timer @ %pa\n",
+		       &timer_mem->cntctlbase);
+
+	return frame;
+}
+
+static int __init
+arch_timer_mem_frame_register(struct arch_timer_mem_frame *frame)
+{
+	void __iomem *base;
+	int ret, irq = 0;
 
 	if (arch_timer_mem_use_virtual)
-		irq = irq_of_parse_and_map(best_frame, ARCH_TIMER_VIRT_SPI);
+		irq = frame->virt_irq;
 	else
-		irq = irq_of_parse_and_map(best_frame, ARCH_TIMER_PHYS_SPI);
+		irq = frame->phys_irq;
 
-	ret = -EINVAL;
 	if (!irq) {
 		pr_err("Frame missing %s irq.\n",
 		       arch_timer_mem_use_virtual ? "virt" : "phys");
-		goto out;
+		return -EINVAL;
+	}
+
+	if (!request_mem_region(frame->cntbase, frame->size,
+				"arch_mem_timer"))
+		return -EBUSY;
+
+	base = ioremap(frame->cntbase, frame->size);
+	if (!base) {
+		pr_err("Can't map frame's registers\n");
+		return -ENXIO;
 	}
 
-	rate = readl(base + CNTFRQ);
-	arch_timer_of_configure_rate(rate, np);
 	ret = arch_timer_mem_register(base, irq);
-	if (ret)
+	if (ret) {
+		iounmap(base);
+		return ret;
+	}
+
+	arch_counter_base = base;
+	arch_timers_present |= ARCH_TIMER_TYPE_MEM;
+
+	return 0;
+}
+
+static int __init arch_timer_mem_of_init(struct device_node *np)
+{
+	struct arch_timer_mem *timer_mem;
+	struct arch_timer_mem_frame *frame;
+	struct device_node *frame_node;
+	struct resource res;
+	int ret = -EINVAL;
+	u32 rate;
+
+	timer_mem = kzalloc(sizeof(*timer_mem), GFP_KERNEL);
+	if (!timer_mem)
+		return -ENOMEM;
+
+	if (of_address_to_resource(np, 0, &res))
 		goto out;
+	timer_mem->cntctlbase = res.start;
+	timer_mem->size = resource_size(&res);
 
-	if (!arch_timer_needs_of_probing())
+	for_each_available_child_of_node(np, frame_node) {
+		u32 n;
+		struct arch_timer_mem_frame *frame;
+
+		if (of_property_read_u32(frame_node, "frame-number", &n)) {
+			pr_err(FW_BUG "Missing frame-number.\n");
+			of_node_put(frame_node);
+			goto out;
+		}
+		if (n >= ARCH_TIMER_MEM_MAX_FRAMES) {
+			pr_err(FW_BUG "Wrong frame-number, only 0-%u are permitted.\n",
+			       ARCH_TIMER_MEM_MAX_FRAMES - 1);
+			of_node_put(frame_node);
+			goto out;
+		}
+		frame = &timer_mem->frame[n];
+
+		if (frame->valid) {
+			pr_err(FW_BUG "Duplicated frame-number.\n");
+			of_node_put(frame_node);
+			goto out;
+		}
+
+		if (of_address_to_resource(frame_node, 0, &res)) {
+			of_node_put(frame_node);
+			goto out;
+		}
+		frame->cntbase = res.start;
+		frame->size = resource_size(&res);
+
+		frame->virt_irq = irq_of_parse_and_map(frame_node,
+						       ARCH_TIMER_VIRT_SPI);
+		frame->phys_irq = irq_of_parse_and_map(frame_node,
+						       ARCH_TIMER_PHYS_SPI);
+
+		frame->valid = true;
+	}
+
+	frame = arch_timer_mem_find_best_frame(timer_mem);
+	if (!frame) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	rate = arch_timer_mem_frame_get_cntfrq(frame);
+	arch_timer_of_configure_rate(rate, np);
+
+	ret = arch_timer_mem_frame_register(frame);
+	if (!ret && !arch_timer_needs_of_probing())
 		ret = arch_timer_common_init();
 out:
-	iounmap(cntctlbase);
-	of_node_put(best_frame);
+	kfree(timer_mem);
 	return ret;
 }
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
-		       arch_timer_mem_init);
+		       arch_timer_mem_of_init);
 
 #ifdef CONFIG_ACPI
 static int __init map_generic_timer_interrupt(u32 interrupt, u32 flags)
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 06/11] acpi/arm64: Add GTDT table parse driver
  2017-04-14 18:40 ` fu.wei at linaro.org
  (?)
@ 2017-04-14 18:40     ` fu.wei
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei-QSEj5FYQhm4dnm+yROfE0A @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw-LthD3rsA81gm4RdzfppkhA, lenb-DgEjT+Ai2ygdnm+yROfE0A,
	daniel.lezcano-QSEj5FYQhm4dnm+yROfE0A,
	tglx-hfZtesqFncYOwBW4kG4KsQ, marc.zyngier-5wv7dgnIgG8,
	mark.rutland-5wv7dgnIgG8, lorenzo.pieralisi-5wv7dgnIgG8,
	sudeep.holla-5wv7dgnIgG8, hanjun.guo-QSEj5FYQhm4dnm+yROfE0A
  Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	linaro-acpi-cunTk1MwBs8s++Sfvej+rw,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA,
	linux-acpi-u79uwXL29TY76Z2rM5mHXA,
	rruigrok-sgV2jX0FEOL9JmXXK+q4OQ, harba-sgV2jX0FEOL9JmXXK+q4OQ,
	cov-sgV2jX0FEOL9JmXXK+q4OQ, timur-sgV2jX0FEOL9JmXXK+q4OQ,
	graeme.gregory-QSEj5FYQhm4dnm+yROfE0A,
	al.stone-QSEj5FYQhm4dnm+yROfE0A, jcm-H+wXaHxf7aLQT0dZR+AlfA,
	wei-H+wXaHxf7aLQT0dZR+AlfA, arnd-r2nGTMty4D4,
	catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8,
	Suravee.Suthikulpanit-5C7GfCeVMHo, leo.duran-5C7GfCeVMHo,
	wim-IQzOog9fTRqzQB+pC5nmwQ, linux-0h96xk9xTtrk1uMJSBkQmQ,
	linux-watchdog-u79uwXL29TY76Z2rM5mHXA, tn-nYOzD4b6Jr9Wk0Htik3J/w,
	christoffer.dall-QSEj5FYQhm4dnm+yROfE0A,
	julien.grall-5wv7dgnIgG8, Fu Wei

From: Fu Wei <fu.wei-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>

This patch adds support for parsing arch timer info in GTDT,
provides some kernel APIs to parse all the PPIs and
always-on info in GTDT and export them.

By this driver, we can simplify arm_arch_timer drivers, and
separate the ACPI GTDT knowledge from it.

Signed-off-by: Fu Wei <fu.wei-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Hanjun Guo <hanjun.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2-hv44wF8Li93QT0dZR+AlfA@public.gmane.org>
Reviewed-by: Hanjun Guo <hanjun.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Tested-by: Hanjun Guo <hanjun.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi-5wv7dgnIgG8@public.gmane.org>
Signed-off-by: Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>
---
 arch/arm64/Kconfig          |   1 +
 drivers/acpi/arm64/Kconfig  |   3 +
 drivers/acpi/arm64/Makefile |   1 +
 drivers/acpi/arm64/gtdt.c   | 157 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/acpi.h        |   6 ++
 5 files changed, 168 insertions(+)

diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
index 3741859..7e2baec 100644
--- a/arch/arm64/Kconfig
+++ b/arch/arm64/Kconfig
@@ -2,6 +2,7 @@ config ARM64
 	def_bool y
 	select ACPI_CCA_REQUIRED if ACPI
 	select ACPI_GENERIC_GSI if ACPI
+	select ACPI_GTDT if ACPI
 	select ACPI_REDUCED_HARDWARE_ONLY if ACPI
 	select ACPI_MCFG if ACPI
 	select ACPI_SPCR_TABLE if ACPI
diff --git a/drivers/acpi/arm64/Kconfig b/drivers/acpi/arm64/Kconfig
index 4616da4..5a6f80f 100644
--- a/drivers/acpi/arm64/Kconfig
+++ b/drivers/acpi/arm64/Kconfig
@@ -4,3 +4,6 @@
 
 config ACPI_IORT
 	bool
+
+config ACPI_GTDT
+	bool
diff --git a/drivers/acpi/arm64/Makefile b/drivers/acpi/arm64/Makefile
index 72331f2..1017def 100644
--- a/drivers/acpi/arm64/Makefile
+++ b/drivers/acpi/arm64/Makefile
@@ -1 +1,2 @@
 obj-$(CONFIG_ACPI_IORT) 	+= iort.o
+obj-$(CONFIG_ACPI_GTDT) 	+= gtdt.o
diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
new file mode 100644
index 0000000..3d95af8
--- /dev/null
+++ b/drivers/acpi/arm64/gtdt.c
@@ -0,0 +1,157 @@
+/*
+ * ARM Specific GTDT table Support
+ *
+ * Copyright (C) 2016, Linaro Ltd.
+ * Author: Daniel Lezcano <daniel.lezcano-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+ *         Fu Wei <fu.wei-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+ *         Hanjun Guo <hanjun.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+#include <clocksource/arm_arch_timer.h>
+
+#undef pr_fmt
+#define pr_fmt(fmt) "ACPI GTDT: " fmt
+
+/**
+ * struct acpi_gtdt_descriptor - Store the key info of GTDT for all functions
+ * @gtdt:	The pointer to the struct acpi_table_gtdt of GTDT table.
+ * @gtdt_end:	The pointer to the end of GTDT table.
+ * @platform_timer:	The pointer to the start of Platform Timer Structure
+ *
+ * The struct store the key info of GTDT table, it should be initialized by
+ * acpi_gtdt_init.
+ */
+struct acpi_gtdt_descriptor {
+	struct acpi_table_gtdt *gtdt;
+	void *gtdt_end;
+	void *platform_timer;
+};
+
+static struct acpi_gtdt_descriptor acpi_gtdt_desc __initdata;
+
+static int __init map_gt_gsi(u32 interrupt, u32 flags)
+{
+	int trigger, polarity;
+
+	trigger = (flags & ACPI_GTDT_INTERRUPT_MODE) ? ACPI_EDGE_SENSITIVE
+			: ACPI_LEVEL_SENSITIVE;
+
+	polarity = (flags & ACPI_GTDT_INTERRUPT_POLARITY) ? ACPI_ACTIVE_LOW
+			: ACPI_ACTIVE_HIGH;
+
+	return acpi_register_gsi(NULL, interrupt, trigger, polarity);
+}
+
+/**
+ * acpi_gtdt_map_ppi() - Map the PPIs of per-cpu arch_timer.
+ * @type:	the type of PPI.
+ *
+ * Note: Secure state is not managed by the kernel on ARM64 systems.
+ * So we only handle the non-secure timer PPIs,
+ * ARCH_TIMER_PHYS_SECURE_PPI is treated as invalid type.
+ *
+ * Return: the mapped PPI value, 0 if error.
+ */
+int __init acpi_gtdt_map_ppi(int type)
+{
+	struct acpi_table_gtdt *gtdt = acpi_gtdt_desc.gtdt;
+
+	switch (type) {
+	case ARCH_TIMER_PHYS_NONSECURE_PPI:
+		return map_gt_gsi(gtdt->non_secure_el1_interrupt,
+				  gtdt->non_secure_el1_flags);
+	case ARCH_TIMER_VIRT_PPI:
+		return map_gt_gsi(gtdt->virtual_timer_interrupt,
+				  gtdt->virtual_timer_flags);
+
+	case ARCH_TIMER_HYP_PPI:
+		return map_gt_gsi(gtdt->non_secure_el2_interrupt,
+				  gtdt->non_secure_el2_flags);
+	default:
+		pr_err("Failed to map timer interrupt: invalid type.\n");
+	}
+
+	return 0;
+}
+
+/**
+ * acpi_gtdt_c3stop() - Got c3stop info from GTDT according to the type of PPI.
+ * @type:	the type of PPI.
+ *
+ * Return: true if the timer HW state is lost when a CPU enters an idle state,
+ * false otherwise
+ */
+bool __init acpi_gtdt_c3stop(int type)
+{
+	struct acpi_table_gtdt *gtdt = acpi_gtdt_desc.gtdt;
+
+	switch (type) {
+	case ARCH_TIMER_PHYS_NONSECURE_PPI:
+		return !(gtdt->non_secure_el1_flags & ACPI_GTDT_ALWAYS_ON);
+
+	case ARCH_TIMER_VIRT_PPI:
+		return !(gtdt->virtual_timer_flags & ACPI_GTDT_ALWAYS_ON);
+
+	case ARCH_TIMER_HYP_PPI:
+		return !(gtdt->non_secure_el2_flags & ACPI_GTDT_ALWAYS_ON);
+
+	default:
+		pr_err("Failed to get c3stop info: invalid type.\n");
+	}
+
+	return false;
+}
+
+/**
+ * acpi_gtdt_init() - Get the info of GTDT table to prepare for further init.
+ * @table:			The pointer to GTDT table.
+ * @platform_timer_count:	It points to a integer variable which is used
+ *				for storing the number of platform timers.
+ *				This pointer could be NULL, if the caller
+ *				doesn't need this info.
+ *
+ * Return: 0 if success, -EINVAL if error.
+ */
+int __init acpi_gtdt_init(struct acpi_table_header *table,
+			  int *platform_timer_count)
+{
+	void *platform_timer;
+	struct acpi_table_gtdt *gtdt;
+
+	gtdt = container_of(table, struct acpi_table_gtdt, header);
+	acpi_gtdt_desc.gtdt = gtdt;
+	acpi_gtdt_desc.gtdt_end = (void *)table + table->length;
+	acpi_gtdt_desc.platform_timer = NULL;
+	if (platform_timer_count)
+		*platform_timer_count = 0;
+
+	if (table->revision < 2) {
+		pr_warn("Revision:%d doesn't support Platform Timers.\n",
+			table->revision);
+		return 0;
+	}
+
+	if (!gtdt->platform_timer_count) {
+		pr_debug("No Platform Timer.\n");
+		return 0;
+	}
+
+	platform_timer = (void *)gtdt + gtdt->platform_timer_offset;
+	if (platform_timer < (void *)table + sizeof(struct acpi_table_gtdt)) {
+		pr_err(FW_BUG "invalid timer data.\n");
+		return -EINVAL;
+	}
+	acpi_gtdt_desc.platform_timer = platform_timer;
+	if (platform_timer_count)
+		*platform_timer_count = gtdt->platform_timer_count;
+
+	return 0;
+}
diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 9b05886..4b5c146 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -595,6 +595,12 @@ enum acpi_reconfig_event  {
 int acpi_reconfig_notifier_register(struct notifier_block *nb);
 int acpi_reconfig_notifier_unregister(struct notifier_block *nb);
 
+#ifdef CONFIG_ACPI_GTDT
+int acpi_gtdt_init(struct acpi_table_header *table, int *platform_timer_count);
+int acpi_gtdt_map_ppi(int type);
+bool acpi_gtdt_c3stop(int type);
+#endif
+
 #else	/* !CONFIG_ACPI */
 
 #define acpi_disabled 1
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 06/11] acpi/arm64: Add GTDT table parse driver
@ 2017-04-14 18:40     ` fu.wei
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

This patch adds support for parsing arch timer info in GTDT,
provides some kernel APIs to parse all the PPIs and
always-on info in GTDT and export them.

By this driver, we can simplify arm_arch_timer drivers, and
separate the ACPI GTDT knowledge from it.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 arch/arm64/Kconfig          |   1 +
 drivers/acpi/arm64/Kconfig  |   3 +
 drivers/acpi/arm64/Makefile |   1 +
 drivers/acpi/arm64/gtdt.c   | 157 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/acpi.h        |   6 ++
 5 files changed, 168 insertions(+)

diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
index 3741859..7e2baec 100644
--- a/arch/arm64/Kconfig
+++ b/arch/arm64/Kconfig
@@ -2,6 +2,7 @@ config ARM64
 	def_bool y
 	select ACPI_CCA_REQUIRED if ACPI
 	select ACPI_GENERIC_GSI if ACPI
+	select ACPI_GTDT if ACPI
 	select ACPI_REDUCED_HARDWARE_ONLY if ACPI
 	select ACPI_MCFG if ACPI
 	select ACPI_SPCR_TABLE if ACPI
diff --git a/drivers/acpi/arm64/Kconfig b/drivers/acpi/arm64/Kconfig
index 4616da4..5a6f80f 100644
--- a/drivers/acpi/arm64/Kconfig
+++ b/drivers/acpi/arm64/Kconfig
@@ -4,3 +4,6 @@
 
 config ACPI_IORT
 	bool
+
+config ACPI_GTDT
+	bool
diff --git a/drivers/acpi/arm64/Makefile b/drivers/acpi/arm64/Makefile
index 72331f2..1017def 100644
--- a/drivers/acpi/arm64/Makefile
+++ b/drivers/acpi/arm64/Makefile
@@ -1 +1,2 @@
 obj-$(CONFIG_ACPI_IORT) 	+= iort.o
+obj-$(CONFIG_ACPI_GTDT) 	+= gtdt.o
diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
new file mode 100644
index 0000000..3d95af8
--- /dev/null
+++ b/drivers/acpi/arm64/gtdt.c
@@ -0,0 +1,157 @@
+/*
+ * ARM Specific GTDT table Support
+ *
+ * Copyright (C) 2016, Linaro Ltd.
+ * Author: Daniel Lezcano <daniel.lezcano@linaro.org>
+ *         Fu Wei <fu.wei@linaro.org>
+ *         Hanjun Guo <hanjun.guo@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+#include <clocksource/arm_arch_timer.h>
+
+#undef pr_fmt
+#define pr_fmt(fmt) "ACPI GTDT: " fmt
+
+/**
+ * struct acpi_gtdt_descriptor - Store the key info of GTDT for all functions
+ * @gtdt:	The pointer to the struct acpi_table_gtdt of GTDT table.
+ * @gtdt_end:	The pointer to the end of GTDT table.
+ * @platform_timer:	The pointer to the start of Platform Timer Structure
+ *
+ * The struct store the key info of GTDT table, it should be initialized by
+ * acpi_gtdt_init.
+ */
+struct acpi_gtdt_descriptor {
+	struct acpi_table_gtdt *gtdt;
+	void *gtdt_end;
+	void *platform_timer;
+};
+
+static struct acpi_gtdt_descriptor acpi_gtdt_desc __initdata;
+
+static int __init map_gt_gsi(u32 interrupt, u32 flags)
+{
+	int trigger, polarity;
+
+	trigger = (flags & ACPI_GTDT_INTERRUPT_MODE) ? ACPI_EDGE_SENSITIVE
+			: ACPI_LEVEL_SENSITIVE;
+
+	polarity = (flags & ACPI_GTDT_INTERRUPT_POLARITY) ? ACPI_ACTIVE_LOW
+			: ACPI_ACTIVE_HIGH;
+
+	return acpi_register_gsi(NULL, interrupt, trigger, polarity);
+}
+
+/**
+ * acpi_gtdt_map_ppi() - Map the PPIs of per-cpu arch_timer.
+ * @type:	the type of PPI.
+ *
+ * Note: Secure state is not managed by the kernel on ARM64 systems.
+ * So we only handle the non-secure timer PPIs,
+ * ARCH_TIMER_PHYS_SECURE_PPI is treated as invalid type.
+ *
+ * Return: the mapped PPI value, 0 if error.
+ */
+int __init acpi_gtdt_map_ppi(int type)
+{
+	struct acpi_table_gtdt *gtdt = acpi_gtdt_desc.gtdt;
+
+	switch (type) {
+	case ARCH_TIMER_PHYS_NONSECURE_PPI:
+		return map_gt_gsi(gtdt->non_secure_el1_interrupt,
+				  gtdt->non_secure_el1_flags);
+	case ARCH_TIMER_VIRT_PPI:
+		return map_gt_gsi(gtdt->virtual_timer_interrupt,
+				  gtdt->virtual_timer_flags);
+
+	case ARCH_TIMER_HYP_PPI:
+		return map_gt_gsi(gtdt->non_secure_el2_interrupt,
+				  gtdt->non_secure_el2_flags);
+	default:
+		pr_err("Failed to map timer interrupt: invalid type.\n");
+	}
+
+	return 0;
+}
+
+/**
+ * acpi_gtdt_c3stop() - Got c3stop info from GTDT according to the type of PPI.
+ * @type:	the type of PPI.
+ *
+ * Return: true if the timer HW state is lost when a CPU enters an idle state,
+ * false otherwise
+ */
+bool __init acpi_gtdt_c3stop(int type)
+{
+	struct acpi_table_gtdt *gtdt = acpi_gtdt_desc.gtdt;
+
+	switch (type) {
+	case ARCH_TIMER_PHYS_NONSECURE_PPI:
+		return !(gtdt->non_secure_el1_flags & ACPI_GTDT_ALWAYS_ON);
+
+	case ARCH_TIMER_VIRT_PPI:
+		return !(gtdt->virtual_timer_flags & ACPI_GTDT_ALWAYS_ON);
+
+	case ARCH_TIMER_HYP_PPI:
+		return !(gtdt->non_secure_el2_flags & ACPI_GTDT_ALWAYS_ON);
+
+	default:
+		pr_err("Failed to get c3stop info: invalid type.\n");
+	}
+
+	return false;
+}
+
+/**
+ * acpi_gtdt_init() - Get the info of GTDT table to prepare for further init.
+ * @table:			The pointer to GTDT table.
+ * @platform_timer_count:	It points to a integer variable which is used
+ *				for storing the number of platform timers.
+ *				This pointer could be NULL, if the caller
+ *				doesn't need this info.
+ *
+ * Return: 0 if success, -EINVAL if error.
+ */
+int __init acpi_gtdt_init(struct acpi_table_header *table,
+			  int *platform_timer_count)
+{
+	void *platform_timer;
+	struct acpi_table_gtdt *gtdt;
+
+	gtdt = container_of(table, struct acpi_table_gtdt, header);
+	acpi_gtdt_desc.gtdt = gtdt;
+	acpi_gtdt_desc.gtdt_end = (void *)table + table->length;
+	acpi_gtdt_desc.platform_timer = NULL;
+	if (platform_timer_count)
+		*platform_timer_count = 0;
+
+	if (table->revision < 2) {
+		pr_warn("Revision:%d doesn't support Platform Timers.\n",
+			table->revision);
+		return 0;
+	}
+
+	if (!gtdt->platform_timer_count) {
+		pr_debug("No Platform Timer.\n");
+		return 0;
+	}
+
+	platform_timer = (void *)gtdt + gtdt->platform_timer_offset;
+	if (platform_timer < (void *)table + sizeof(struct acpi_table_gtdt)) {
+		pr_err(FW_BUG "invalid timer data.\n");
+		return -EINVAL;
+	}
+	acpi_gtdt_desc.platform_timer = platform_timer;
+	if (platform_timer_count)
+		*platform_timer_count = gtdt->platform_timer_count;
+
+	return 0;
+}
diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 9b05886..4b5c146 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -595,6 +595,12 @@ enum acpi_reconfig_event  {
 int acpi_reconfig_notifier_register(struct notifier_block *nb);
 int acpi_reconfig_notifier_unregister(struct notifier_block *nb);
 
+#ifdef CONFIG_ACPI_GTDT
+int acpi_gtdt_init(struct acpi_table_header *table, int *platform_timer_count);
+int acpi_gtdt_map_ppi(int type);
+bool acpi_gtdt_c3stop(int type);
+#endif
+
 #else	/* !CONFIG_ACPI */
 
 #define acpi_disabled 1
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 06/11] acpi/arm64: Add GTDT table parse driver
@ 2017-04-14 18:40     ` fu.wei
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

This patch adds support for parsing arch timer info in GTDT,
provides some kernel APIs to parse all the PPIs and
always-on info in GTDT and export them.

By this driver, we can simplify arm_arch_timer drivers, and
separate the ACPI GTDT knowledge from it.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 arch/arm64/Kconfig          |   1 +
 drivers/acpi/arm64/Kconfig  |   3 +
 drivers/acpi/arm64/Makefile |   1 +
 drivers/acpi/arm64/gtdt.c   | 157 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/acpi.h        |   6 ++
 5 files changed, 168 insertions(+)

diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
index 3741859..7e2baec 100644
--- a/arch/arm64/Kconfig
+++ b/arch/arm64/Kconfig
@@ -2,6 +2,7 @@ config ARM64
 	def_bool y
 	select ACPI_CCA_REQUIRED if ACPI
 	select ACPI_GENERIC_GSI if ACPI
+	select ACPI_GTDT if ACPI
 	select ACPI_REDUCED_HARDWARE_ONLY if ACPI
 	select ACPI_MCFG if ACPI
 	select ACPI_SPCR_TABLE if ACPI
diff --git a/drivers/acpi/arm64/Kconfig b/drivers/acpi/arm64/Kconfig
index 4616da4..5a6f80f 100644
--- a/drivers/acpi/arm64/Kconfig
+++ b/drivers/acpi/arm64/Kconfig
@@ -4,3 +4,6 @@
 
 config ACPI_IORT
 	bool
+
+config ACPI_GTDT
+	bool
diff --git a/drivers/acpi/arm64/Makefile b/drivers/acpi/arm64/Makefile
index 72331f2..1017def 100644
--- a/drivers/acpi/arm64/Makefile
+++ b/drivers/acpi/arm64/Makefile
@@ -1 +1,2 @@
 obj-$(CONFIG_ACPI_IORT) 	+= iort.o
+obj-$(CONFIG_ACPI_GTDT) 	+= gtdt.o
diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
new file mode 100644
index 0000000..3d95af8
--- /dev/null
+++ b/drivers/acpi/arm64/gtdt.c
@@ -0,0 +1,157 @@
+/*
+ * ARM Specific GTDT table Support
+ *
+ * Copyright (C) 2016, Linaro Ltd.
+ * Author: Daniel Lezcano <daniel.lezcano@linaro.org>
+ *         Fu Wei <fu.wei@linaro.org>
+ *         Hanjun Guo <hanjun.guo@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+#include <clocksource/arm_arch_timer.h>
+
+#undef pr_fmt
+#define pr_fmt(fmt) "ACPI GTDT: " fmt
+
+/**
+ * struct acpi_gtdt_descriptor - Store the key info of GTDT for all functions
+ * @gtdt:	The pointer to the struct acpi_table_gtdt of GTDT table.
+ * @gtdt_end:	The pointer to the end of GTDT table.
+ * @platform_timer:	The pointer to the start of Platform Timer Structure
+ *
+ * The struct store the key info of GTDT table, it should be initialized by
+ * acpi_gtdt_init.
+ */
+struct acpi_gtdt_descriptor {
+	struct acpi_table_gtdt *gtdt;
+	void *gtdt_end;
+	void *platform_timer;
+};
+
+static struct acpi_gtdt_descriptor acpi_gtdt_desc __initdata;
+
+static int __init map_gt_gsi(u32 interrupt, u32 flags)
+{
+	int trigger, polarity;
+
+	trigger = (flags & ACPI_GTDT_INTERRUPT_MODE) ? ACPI_EDGE_SENSITIVE
+			: ACPI_LEVEL_SENSITIVE;
+
+	polarity = (flags & ACPI_GTDT_INTERRUPT_POLARITY) ? ACPI_ACTIVE_LOW
+			: ACPI_ACTIVE_HIGH;
+
+	return acpi_register_gsi(NULL, interrupt, trigger, polarity);
+}
+
+/**
+ * acpi_gtdt_map_ppi() - Map the PPIs of per-cpu arch_timer.
+ * @type:	the type of PPI.
+ *
+ * Note: Secure state is not managed by the kernel on ARM64 systems.
+ * So we only handle the non-secure timer PPIs,
+ * ARCH_TIMER_PHYS_SECURE_PPI is treated as invalid type.
+ *
+ * Return: the mapped PPI value, 0 if error.
+ */
+int __init acpi_gtdt_map_ppi(int type)
+{
+	struct acpi_table_gtdt *gtdt = acpi_gtdt_desc.gtdt;
+
+	switch (type) {
+	case ARCH_TIMER_PHYS_NONSECURE_PPI:
+		return map_gt_gsi(gtdt->non_secure_el1_interrupt,
+				  gtdt->non_secure_el1_flags);
+	case ARCH_TIMER_VIRT_PPI:
+		return map_gt_gsi(gtdt->virtual_timer_interrupt,
+				  gtdt->virtual_timer_flags);
+
+	case ARCH_TIMER_HYP_PPI:
+		return map_gt_gsi(gtdt->non_secure_el2_interrupt,
+				  gtdt->non_secure_el2_flags);
+	default:
+		pr_err("Failed to map timer interrupt: invalid type.\n");
+	}
+
+	return 0;
+}
+
+/**
+ * acpi_gtdt_c3stop() - Got c3stop info from GTDT according to the type of PPI.
+ * @type:	the type of PPI.
+ *
+ * Return: true if the timer HW state is lost when a CPU enters an idle state,
+ * false otherwise
+ */
+bool __init acpi_gtdt_c3stop(int type)
+{
+	struct acpi_table_gtdt *gtdt = acpi_gtdt_desc.gtdt;
+
+	switch (type) {
+	case ARCH_TIMER_PHYS_NONSECURE_PPI:
+		return !(gtdt->non_secure_el1_flags & ACPI_GTDT_ALWAYS_ON);
+
+	case ARCH_TIMER_VIRT_PPI:
+		return !(gtdt->virtual_timer_flags & ACPI_GTDT_ALWAYS_ON);
+
+	case ARCH_TIMER_HYP_PPI:
+		return !(gtdt->non_secure_el2_flags & ACPI_GTDT_ALWAYS_ON);
+
+	default:
+		pr_err("Failed to get c3stop info: invalid type.\n");
+	}
+
+	return false;
+}
+
+/**
+ * acpi_gtdt_init() - Get the info of GTDT table to prepare for further init.
+ * @table:			The pointer to GTDT table.
+ * @platform_timer_count:	It points to a integer variable which is used
+ *				for storing the number of platform timers.
+ *				This pointer could be NULL, if the caller
+ *				doesn't need this info.
+ *
+ * Return: 0 if success, -EINVAL if error.
+ */
+int __init acpi_gtdt_init(struct acpi_table_header *table,
+			  int *platform_timer_count)
+{
+	void *platform_timer;
+	struct acpi_table_gtdt *gtdt;
+
+	gtdt = container_of(table, struct acpi_table_gtdt, header);
+	acpi_gtdt_desc.gtdt = gtdt;
+	acpi_gtdt_desc.gtdt_end = (void *)table + table->length;
+	acpi_gtdt_desc.platform_timer = NULL;
+	if (platform_timer_count)
+		*platform_timer_count = 0;
+
+	if (table->revision < 2) {
+		pr_warn("Revision:%d doesn't support Platform Timers.\n",
+			table->revision);
+		return 0;
+	}
+
+	if (!gtdt->platform_timer_count) {
+		pr_debug("No Platform Timer.\n");
+		return 0;
+	}
+
+	platform_timer = (void *)gtdt + gtdt->platform_timer_offset;
+	if (platform_timer < (void *)table + sizeof(struct acpi_table_gtdt)) {
+		pr_err(FW_BUG "invalid timer data.\n");
+		return -EINVAL;
+	}
+	acpi_gtdt_desc.platform_timer = platform_timer;
+	if (platform_timer_count)
+		*platform_timer_count = gtdt->platform_timer_count;
+
+	return 0;
+}
diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 9b05886..4b5c146 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -595,6 +595,12 @@ enum acpi_reconfig_event  {
 int acpi_reconfig_notifier_register(struct notifier_block *nb);
 int acpi_reconfig_notifier_unregister(struct notifier_block *nb);
 
+#ifdef CONFIG_ACPI_GTDT
+int acpi_gtdt_init(struct acpi_table_header *table, int *platform_timer_count);
+int acpi_gtdt_map_ppi(int type);
+bool acpi_gtdt_c3stop(int type);
+#endif
+
 #else	/* !CONFIG_ACPI */
 
 #define acpi_disabled 1
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 07/11] clocksource: arm_arch_timer: simplify ACPI support code.
  2017-04-14 18:40 ` fu.wei at linaro.org
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

The patch update arm_arch_timer driver to use the function
provided by the new GTDT driver of ACPI.
By this way, arm_arch_timer.c can be simplified, and separate
all the ACPI GTDT knowledge from this timer driver.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 40 +++++++++---------------------------
 1 file changed, 10 insertions(+), 30 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index dad0264..05f2f7a 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1384,53 +1384,33 @@ static int __init arch_timer_mem_of_init(struct device_node *np)
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
 		       arch_timer_mem_of_init);
 
-#ifdef CONFIG_ACPI
-static int __init map_generic_timer_interrupt(u32 interrupt, u32 flags)
-{
-	int trigger, polarity;
-
-	if (!interrupt)
-		return 0;
-
-	trigger = (flags & ACPI_GTDT_INTERRUPT_MODE) ? ACPI_EDGE_SENSITIVE
-			: ACPI_LEVEL_SENSITIVE;
-
-	polarity = (flags & ACPI_GTDT_INTERRUPT_POLARITY) ? ACPI_ACTIVE_LOW
-			: ACPI_ACTIVE_HIGH;
-
-	return acpi_register_gsi(NULL, interrupt, trigger, polarity);
-}
-
+#ifdef CONFIG_ACPI_GTDT
 /* Initialize per-processor generic timer */
 static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 {
 	int ret;
-	struct acpi_table_gtdt *gtdt;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
 		pr_warn("already initialized, skipping\n");
 		return -EINVAL;
 	}
 
-	gtdt = container_of(table, struct acpi_table_gtdt, header);
-
 	arch_timers_present |= ARCH_TIMER_TYPE_CP15;
 
-	arch_timer_ppi[ARCH_TIMER_PHYS_SECURE_PPI] =
-		map_generic_timer_interrupt(gtdt->secure_el1_interrupt,
-		gtdt->secure_el1_flags);
+	ret = acpi_gtdt_init(table, NULL);
+	if (ret) {
+		pr_err("Failed to init GTDT table.\n");
+		return ret;
+	}
 
 	arch_timer_ppi[ARCH_TIMER_PHYS_NONSECURE_PPI] =
-		map_generic_timer_interrupt(gtdt->non_secure_el1_interrupt,
-		gtdt->non_secure_el1_flags);
+		acpi_gtdt_map_ppi(ARCH_TIMER_PHYS_NONSECURE_PPI);
 
 	arch_timer_ppi[ARCH_TIMER_VIRT_PPI] =
-		map_generic_timer_interrupt(gtdt->virtual_timer_interrupt,
-		gtdt->virtual_timer_flags);
+		acpi_gtdt_map_ppi(ARCH_TIMER_VIRT_PPI);
 
 	arch_timer_ppi[ARCH_TIMER_HYP_PPI] =
-		map_generic_timer_interrupt(gtdt->non_secure_el2_interrupt,
-		gtdt->non_secure_el2_flags);
+		acpi_gtdt_map_ppi(ARCH_TIMER_HYP_PPI);
 
 	arch_timer_kvm_info.virtual_irq = arch_timer_ppi[ARCH_TIMER_VIRT_PPI];
 
@@ -1451,7 +1431,7 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 	}
 
 	/* Always-on capability */
-	arch_timer_c3stop = !(gtdt->non_secure_el1_flags & ACPI_GTDT_ALWAYS_ON);
+	arch_timer_c3stop = acpi_gtdt_c3stop(arch_timer_uses_ppi);
 
 	/* Check for globally applicable workarounds */
 	arch_timer_check_ool_workaround(ate_match_acpi_oem_info, table);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 07/11] clocksource: arm_arch_timer: simplify ACPI support code.
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

The patch update arm_arch_timer driver to use the function
provided by the new GTDT driver of ACPI.
By this way, arm_arch_timer.c can be simplified, and separate
all the ACPI GTDT knowledge from this timer driver.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 40 +++++++++---------------------------
 1 file changed, 10 insertions(+), 30 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index dad0264..05f2f7a 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1384,53 +1384,33 @@ static int __init arch_timer_mem_of_init(struct device_node *np)
 CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
 		       arch_timer_mem_of_init);
 
-#ifdef CONFIG_ACPI
-static int __init map_generic_timer_interrupt(u32 interrupt, u32 flags)
-{
-	int trigger, polarity;
-
-	if (!interrupt)
-		return 0;
-
-	trigger = (flags & ACPI_GTDT_INTERRUPT_MODE) ? ACPI_EDGE_SENSITIVE
-			: ACPI_LEVEL_SENSITIVE;
-
-	polarity = (flags & ACPI_GTDT_INTERRUPT_POLARITY) ? ACPI_ACTIVE_LOW
-			: ACPI_ACTIVE_HIGH;
-
-	return acpi_register_gsi(NULL, interrupt, trigger, polarity);
-}
-
+#ifdef CONFIG_ACPI_GTDT
 /* Initialize per-processor generic timer */
 static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 {
 	int ret;
-	struct acpi_table_gtdt *gtdt;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
 		pr_warn("already initialized, skipping\n");
 		return -EINVAL;
 	}
 
-	gtdt = container_of(table, struct acpi_table_gtdt, header);
-
 	arch_timers_present |= ARCH_TIMER_TYPE_CP15;
 
-	arch_timer_ppi[ARCH_TIMER_PHYS_SECURE_PPI] =
-		map_generic_timer_interrupt(gtdt->secure_el1_interrupt,
-		gtdt->secure_el1_flags);
+	ret = acpi_gtdt_init(table, NULL);
+	if (ret) {
+		pr_err("Failed to init GTDT table.\n");
+		return ret;
+	}
 
 	arch_timer_ppi[ARCH_TIMER_PHYS_NONSECURE_PPI] =
-		map_generic_timer_interrupt(gtdt->non_secure_el1_interrupt,
-		gtdt->non_secure_el1_flags);
+		acpi_gtdt_map_ppi(ARCH_TIMER_PHYS_NONSECURE_PPI);
 
 	arch_timer_ppi[ARCH_TIMER_VIRT_PPI] =
-		map_generic_timer_interrupt(gtdt->virtual_timer_interrupt,
-		gtdt->virtual_timer_flags);
+		acpi_gtdt_map_ppi(ARCH_TIMER_VIRT_PPI);
 
 	arch_timer_ppi[ARCH_TIMER_HYP_PPI] =
-		map_generic_timer_interrupt(gtdt->non_secure_el2_interrupt,
-		gtdt->non_secure_el2_flags);
+		acpi_gtdt_map_ppi(ARCH_TIMER_HYP_PPI);
 
 	arch_timer_kvm_info.virtual_irq = arch_timer_ppi[ARCH_TIMER_VIRT_PPI];
 
@@ -1451,7 +1431,7 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 	}
 
 	/* Always-on capability */
-	arch_timer_c3stop = !(gtdt->non_secure_el1_flags & ACPI_GTDT_ALWAYS_ON);
+	arch_timer_c3stop = acpi_gtdt_c3stop(arch_timer_uses_ppi);
 
 	/* Check for globally applicable workarounds */
 	arch_timer_check_ool_workaround(ate_match_acpi_oem_info, table);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 08/11] acpi: Introduce acpi_unregister_irq function
  2017-04-14 18:40 ` fu.wei at linaro.org
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

This patch introduces acpi_unregister_irq function to free a
linux IRQ number<->GSI mapping by a given linux IRQ number.

Even we have successfully registered the GSI, when some error occurs, we
may need to unmap it for freeing the IRQ resource. But in some cases, we
only have IRQ, but not GSI.

This patch is the preparation for memory-mapped timer support in GTDT
driver.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
---
 drivers/acpi/irq.c   | 10 ++++++++++
 include/linux/acpi.h |  7 +++++++
 2 files changed, 17 insertions(+)

diff --git a/drivers/acpi/irq.c b/drivers/acpi/irq.c
index 830299a..59de777 100644
--- a/drivers/acpi/irq.c
+++ b/drivers/acpi/irq.c
@@ -85,6 +85,16 @@ void acpi_unregister_gsi(u32 gsi)
 EXPORT_SYMBOL_GPL(acpi_unregister_gsi);
 
 /**
+ * acpi_unregister_irq() - Free a linux IRQ number<->GSI mapping
+ * @irq: linux IRQ number
+ */
+void acpi_unregister_irq(int irq)
+{
+	irq_dispose_mapping(irq);
+}
+EXPORT_SYMBOL_GPL(acpi_unregister_irq);
+
+/**
  * acpi_get_irq_source_fwhandle() - Retrieve fwhandle from IRQ resource source.
  * @source: acpi_resource_source to use for the lookup.
  *
diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 4b5c146..728d1ed 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -336,6 +336,13 @@ extern int acpi_get_override_irq(u32 gsi, int *trigger, int *polarity);
  */
 void acpi_unregister_gsi (u32 gsi);
 
+/*
+ * This function undoes the effect of one call to acpi_register_gsi().
+ * The irq should be the return value of acpi_register_gsi().
+ * If the irq is valid, free a linux IRQ number<->GSI mapping.
+ */
+void acpi_unregister_irq(int irq);
+
 struct pci_dev;
 
 int acpi_pci_irq_enable (struct pci_dev *dev);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 08/11] acpi: Introduce acpi_unregister_irq function
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

This patch introduces acpi_unregister_irq function to free a
linux IRQ number<->GSI mapping by a given linux IRQ number.

Even we have successfully registered the GSI, when some error occurs, we
may need to unmap it for freeing the IRQ resource. But in some cases, we
only have IRQ, but not GSI.

This patch is the preparation for memory-mapped timer support in GTDT
driver.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
---
 drivers/acpi/irq.c   | 10 ++++++++++
 include/linux/acpi.h |  7 +++++++
 2 files changed, 17 insertions(+)

diff --git a/drivers/acpi/irq.c b/drivers/acpi/irq.c
index 830299a..59de777 100644
--- a/drivers/acpi/irq.c
+++ b/drivers/acpi/irq.c
@@ -85,6 +85,16 @@ void acpi_unregister_gsi(u32 gsi)
 EXPORT_SYMBOL_GPL(acpi_unregister_gsi);
 
 /**
+ * acpi_unregister_irq() - Free a linux IRQ number<->GSI mapping
+ * @irq: linux IRQ number
+ */
+void acpi_unregister_irq(int irq)
+{
+	irq_dispose_mapping(irq);
+}
+EXPORT_SYMBOL_GPL(acpi_unregister_irq);
+
+/**
  * acpi_get_irq_source_fwhandle() - Retrieve fwhandle from IRQ resource source.
  * @source: acpi_resource_source to use for the lookup.
  *
diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 4b5c146..728d1ed 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -336,6 +336,13 @@ extern int acpi_get_override_irq(u32 gsi, int *trigger, int *polarity);
  */
 void acpi_unregister_gsi (u32 gsi);
 
+/*
+ * This function undoes the effect of one call to acpi_register_gsi().
+ * The irq should be the return value of acpi_register_gsi().
+ * If the irq is valid, free a linux IRQ number<->GSI mapping.
+ */
+void acpi_unregister_irq(int irq);
+
 struct pci_dev;
 
 int acpi_pci_irq_enable (struct pci_dev *dev);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
  2017-04-14 18:40 ` fu.wei at linaro.org
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

On platforms booting with ACPI, architected memory-mapped timers'
configuration data is provided by firmware through the ACPI GTDT
static table.

The clocksource architected timer kernel driver requires a firmware
interface to collect timer configuration and configure its driver.
this infrastructure is present for device tree systems, but it is
missing on systems booting with ACPI.

Implement the kernel infrastructure required to parse the static
ACPI GTDT table so that the architected timer clocksource driver can
make use of it on systems booting with ACPI, therefore enabling
the corresponding timers configuration.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/acpi/arm64/gtdt.c | 144 ++++++++++++++++++++++++++++++++++++++++++++++
 include/linux/acpi.h      |   1 +
 2 files changed, 145 insertions(+)

diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
index 3d95af8..c9ef9c2 100644
--- a/drivers/acpi/arm64/gtdt.c
+++ b/drivers/acpi/arm64/gtdt.c
@@ -13,6 +13,7 @@
 
 #include <linux/acpi.h>
 #include <linux/init.h>
+#include <linux/irqdomain.h>
 #include <linux/kernel.h>
 
 #include <clocksource/arm_arch_timer.h>
@@ -37,6 +38,28 @@ struct acpi_gtdt_descriptor {
 
 static struct acpi_gtdt_descriptor acpi_gtdt_desc __initdata;
 
+static inline void *next_platform_timer(void *platform_timer)
+{
+	struct acpi_gtdt_header *gh = platform_timer;
+
+	platform_timer += gh->length;
+	if (platform_timer < acpi_gtdt_desc.gtdt_end)
+		return platform_timer;
+
+	return NULL;
+}
+
+#define for_each_platform_timer(_g)				\
+	for (_g = acpi_gtdt_desc.platform_timer; _g;	\
+	     _g = next_platform_timer(_g))
+
+static inline bool is_timer_block(void *platform_timer)
+{
+	struct acpi_gtdt_header *gh = platform_timer;
+
+	return gh->type == ACPI_GTDT_TYPE_TIMER_BLOCK;
+}
+
 static int __init map_gt_gsi(u32 interrupt, u32 flags)
 {
 	int trigger, polarity;
@@ -155,3 +178,124 @@ int __init acpi_gtdt_init(struct acpi_table_header *table,
 
 	return 0;
 }
+
+static int __init gtdt_parse_timer_block(struct acpi_gtdt_timer_block *block,
+					 struct arch_timer_mem *timer_mem)
+{
+	int i;
+	struct arch_timer_mem_frame *frame;
+	struct acpi_gtdt_timer_entry *gtdt_frame;
+
+	if (!block->timer_count) {
+		pr_err(FW_BUG "GT block present, but frame count is zero.");
+		return -ENODEV;
+	}
+
+	if (block->timer_count > ARCH_TIMER_MEM_MAX_FRAMES) {
+		pr_err(FW_BUG "GT block lists %d frames, ACPI spec only allows 8\n",
+		       block->timer_count);
+		return -EINVAL;
+	}
+
+	timer_mem->cntctlbase = (phys_addr_t)block->block_address;
+	/*
+	 * The CNTCTLBase frame is 4KB (register offsets 0x000 - 0xFFC).
+	 * See ARM DDI 0487A.k_iss10775, page I1-5129, Table I1-3
+	 * "CNTCTLBase memory map".
+	 */
+	timer_mem->size = SZ_4K;
+
+	gtdt_frame = (void *)block + block->timer_offset;
+	if (gtdt_frame + block->timer_count != (void *)block + block->header.length)
+		return -EINVAL;
+
+	/*
+	 * Get the GT timer Frame data for every GT Block Timer
+	 */
+	for (i = 0; i < block->timer_count; i++, gtdt_frame++) {
+		if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
+			continue;
+
+		if (!gtdt_frame->base_address || !gtdt_frame->timer_interrupt)
+			goto error;
+
+		frame = &timer_mem->frame[gtdt_frame->frame_number];
+		frame->phys_irq = map_gt_gsi(gtdt_frame->timer_interrupt,
+					     gtdt_frame->timer_flags);
+		if (frame->phys_irq <= 0) {
+			pr_warn("failed to map physical timer irq in frame %d.\n",
+				gtdt_frame->frame_number);
+			goto error;
+		}
+
+		if (gtdt_frame->virtual_timer_interrupt) {
+			frame->virt_irq =
+				map_gt_gsi(gtdt_frame->virtual_timer_interrupt,
+					   gtdt_frame->virtual_timer_flags);
+			if (frame->virt_irq <= 0) {
+				pr_warn("failed to map virtual timer irq in frame %d.\n",
+					gtdt_frame->frame_number);
+				goto error;
+			}
+		} else {
+			frame->virt_irq = 0;
+			pr_debug("virtual timer in frame %d not implemented.\n",
+				 gtdt_frame->frame_number);
+		}
+
+		frame->cntbase = gtdt_frame->base_address;
+		/*
+		 * The CNTBaseN frame is 4KB (register offsets 0x000 - 0xFFC).
+		 * See ARM DDI 0487A.k_iss10775, page I1-5130, Table I1-4
+		 * "CNTBaseN memory map".
+		 */
+		frame->size = SZ_4K;
+		frame->valid = true;
+	}
+
+	return 0;
+
+error:
+	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
+		frame = &timer_mem->frame[i];
+		if (frame->phys_irq > 0)
+			acpi_unregister_irq(frame->phys_irq);
+		if (frame->virt_irq > 0)
+			acpi_unregister_irq(frame->virt_irq);
+	}
+	return -EINVAL;
+}
+
+/**
+ * acpi_arch_timer_mem_init() - Get the info of all GT blocks in GTDT table.
+ * @timer_mem:	The pointer to the array of struct arch_timer_mem for returning
+ *		the result of parsing. The element number of this array should
+ *		be platform_timer_count(the total number of platform timers).
+ * @timer_count: It points to a integer variable which is used for storing the
+ *		number of GT blocks we have parsed.
+ *
+ * Return: 0 if success, -EINVAL/-ENODEV if error.
+ */
+int __init acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem,
+				    int *timer_count)
+{
+	int ret;
+	void *platform_timer;
+
+	*timer_count = 0;
+	for_each_platform_timer(platform_timer) {
+		if (is_timer_block(platform_timer)) {
+			ret = gtdt_parse_timer_block(platform_timer, timer_mem);
+			if (ret)
+				return ret;
+			timer_mem++;
+			(*timer_count)++;
+		}
+	}
+
+	if (*timer_count)
+		pr_info("found %d memory-mapped timer block(s).\n",
+			*timer_count);
+
+	return 0;
+}
diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 728d1ed..4b1ab65 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -606,6 +606,7 @@ int acpi_reconfig_notifier_unregister(struct notifier_block *nb);
 int acpi_gtdt_init(struct acpi_table_header *table, int *platform_timer_count);
 int acpi_gtdt_map_ppi(int type);
 bool acpi_gtdt_c3stop(int type);
+int acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem, int *timer_count);
 #endif
 
 #else	/* !CONFIG_ACPI */
-- 
2.9.3


^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

On platforms booting with ACPI, architected memory-mapped timers'
configuration data is provided by firmware through the ACPI GTDT
static table.

The clocksource architected timer kernel driver requires a firmware
interface to collect timer configuration and configure its driver.
this infrastructure is present for device tree systems, but it is
missing on systems booting with ACPI.

Implement the kernel infrastructure required to parse the static
ACPI GTDT table so that the architected timer clocksource driver can
make use of it on systems booting with ACPI, therefore enabling
the corresponding timers configuration.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/acpi/arm64/gtdt.c | 144 ++++++++++++++++++++++++++++++++++++++++++++++
 include/linux/acpi.h      |   1 +
 2 files changed, 145 insertions(+)

diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
index 3d95af8..c9ef9c2 100644
--- a/drivers/acpi/arm64/gtdt.c
+++ b/drivers/acpi/arm64/gtdt.c
@@ -13,6 +13,7 @@
 
 #include <linux/acpi.h>
 #include <linux/init.h>
+#include <linux/irqdomain.h>
 #include <linux/kernel.h>
 
 #include <clocksource/arm_arch_timer.h>
@@ -37,6 +38,28 @@ struct acpi_gtdt_descriptor {
 
 static struct acpi_gtdt_descriptor acpi_gtdt_desc __initdata;
 
+static inline void *next_platform_timer(void *platform_timer)
+{
+	struct acpi_gtdt_header *gh = platform_timer;
+
+	platform_timer += gh->length;
+	if (platform_timer < acpi_gtdt_desc.gtdt_end)
+		return platform_timer;
+
+	return NULL;
+}
+
+#define for_each_platform_timer(_g)				\
+	for (_g = acpi_gtdt_desc.platform_timer; _g;	\
+	     _g = next_platform_timer(_g))
+
+static inline bool is_timer_block(void *platform_timer)
+{
+	struct acpi_gtdt_header *gh = platform_timer;
+
+	return gh->type == ACPI_GTDT_TYPE_TIMER_BLOCK;
+}
+
 static int __init map_gt_gsi(u32 interrupt, u32 flags)
 {
 	int trigger, polarity;
@@ -155,3 +178,124 @@ int __init acpi_gtdt_init(struct acpi_table_header *table,
 
 	return 0;
 }
+
+static int __init gtdt_parse_timer_block(struct acpi_gtdt_timer_block *block,
+					 struct arch_timer_mem *timer_mem)
+{
+	int i;
+	struct arch_timer_mem_frame *frame;
+	struct acpi_gtdt_timer_entry *gtdt_frame;
+
+	if (!block->timer_count) {
+		pr_err(FW_BUG "GT block present, but frame count is zero.");
+		return -ENODEV;
+	}
+
+	if (block->timer_count > ARCH_TIMER_MEM_MAX_FRAMES) {
+		pr_err(FW_BUG "GT block lists %d frames, ACPI spec only allows 8\n",
+		       block->timer_count);
+		return -EINVAL;
+	}
+
+	timer_mem->cntctlbase = (phys_addr_t)block->block_address;
+	/*
+	 * The CNTCTLBase frame is 4KB (register offsets 0x000 - 0xFFC).
+	 * See ARM DDI 0487A.k_iss10775, page I1-5129, Table I1-3
+	 * "CNTCTLBase memory map".
+	 */
+	timer_mem->size = SZ_4K;
+
+	gtdt_frame = (void *)block + block->timer_offset;
+	if (gtdt_frame + block->timer_count != (void *)block + block->header.length)
+		return -EINVAL;
+
+	/*
+	 * Get the GT timer Frame data for every GT Block Timer
+	 */
+	for (i = 0; i < block->timer_count; i++, gtdt_frame++) {
+		if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
+			continue;
+
+		if (!gtdt_frame->base_address || !gtdt_frame->timer_interrupt)
+			goto error;
+
+		frame = &timer_mem->frame[gtdt_frame->frame_number];
+		frame->phys_irq = map_gt_gsi(gtdt_frame->timer_interrupt,
+					     gtdt_frame->timer_flags);
+		if (frame->phys_irq <= 0) {
+			pr_warn("failed to map physical timer irq in frame %d.\n",
+				gtdt_frame->frame_number);
+			goto error;
+		}
+
+		if (gtdt_frame->virtual_timer_interrupt) {
+			frame->virt_irq =
+				map_gt_gsi(gtdt_frame->virtual_timer_interrupt,
+					   gtdt_frame->virtual_timer_flags);
+			if (frame->virt_irq <= 0) {
+				pr_warn("failed to map virtual timer irq in frame %d.\n",
+					gtdt_frame->frame_number);
+				goto error;
+			}
+		} else {
+			frame->virt_irq = 0;
+			pr_debug("virtual timer in frame %d not implemented.\n",
+				 gtdt_frame->frame_number);
+		}
+
+		frame->cntbase = gtdt_frame->base_address;
+		/*
+		 * The CNTBaseN frame is 4KB (register offsets 0x000 - 0xFFC).
+		 * See ARM DDI 0487A.k_iss10775, page I1-5130, Table I1-4
+		 * "CNTBaseN memory map".
+		 */
+		frame->size = SZ_4K;
+		frame->valid = true;
+	}
+
+	return 0;
+
+error:
+	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
+		frame = &timer_mem->frame[i];
+		if (frame->phys_irq > 0)
+			acpi_unregister_irq(frame->phys_irq);
+		if (frame->virt_irq > 0)
+			acpi_unregister_irq(frame->virt_irq);
+	}
+	return -EINVAL;
+}
+
+/**
+ * acpi_arch_timer_mem_init() - Get the info of all GT blocks in GTDT table.
+ * @timer_mem:	The pointer to the array of struct arch_timer_mem for returning
+ *		the result of parsing. The element number of this array should
+ *		be platform_timer_count(the total number of platform timers).
+ * @timer_count: It points to a integer variable which is used for storing the
+ *		number of GT blocks we have parsed.
+ *
+ * Return: 0 if success, -EINVAL/-ENODEV if error.
+ */
+int __init acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem,
+				    int *timer_count)
+{
+	int ret;
+	void *platform_timer;
+
+	*timer_count = 0;
+	for_each_platform_timer(platform_timer) {
+		if (is_timer_block(platform_timer)) {
+			ret = gtdt_parse_timer_block(platform_timer, timer_mem);
+			if (ret)
+				return ret;
+			timer_mem++;
+			(*timer_count)++;
+		}
+	}
+
+	if (*timer_count)
+		pr_info("found %d memory-mapped timer block(s).\n",
+			*timer_count);
+
+	return 0;
+}
diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 728d1ed..4b1ab65 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -606,6 +606,7 @@ int acpi_reconfig_notifier_unregister(struct notifier_block *nb);
 int acpi_gtdt_init(struct acpi_table_header *table, int *platform_timer_count);
 int acpi_gtdt_map_ppi(int type);
 bool acpi_gtdt_c3stop(int type);
+int acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem, int *timer_count);
 #endif
 
 #else	/* !CONFIG_ACPI */
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 10/11] clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
  2017-04-14 18:40 ` fu.wei at linaro.org
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

The patch add memory-mapped timer register support by using the
information provided by the new GTDT driver of ACPI.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: verify CNTFRQ, only register the first frame]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 78 ++++++++++++++++++++++++++++++++++--
 1 file changed, 75 insertions(+), 3 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 05f2f7a..8981173 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1385,10 +1385,78 @@ CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
 		       arch_timer_mem_of_init);
 
 #ifdef CONFIG_ACPI_GTDT
-/* Initialize per-processor generic timer */
+static int __init
+arch_timer_mem_verify_cntfrq(struct arch_timer_mem *timer_mem)
+{
+	struct arch_timer_mem_frame *frame;
+	u32 rate;
+	int i;
+
+	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
+		frame = &timer_mem->frame[i];
+
+		if (!frame->valid)
+			continue;
+
+		rate = arch_timer_mem_frame_get_cntfrq(frame);
+		if (rate == arch_timer_rate)
+			continue;
+
+		pr_err(FW_BUG "CNTFRQ mismatch: frame @ %pa: (0x%08lx), CPU: (0x%08lx)\n",
+		       &frame->cntbase,
+		       (unsigned long)rate, (unsigned long)arch_timer_rate);
+
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int __init arch_timer_mem_acpi_init(int platform_timer_count)
+{
+	struct arch_timer_mem *timers, *timer;
+	struct arch_timer_mem_frame *frame;
+	int timer_count, i, ret = 0;
+
+	timers = kcalloc(platform_timer_count, sizeof(*timers), GFP_KERNEL);
+	if (!timers)
+		return -ENOMEM;
+
+	ret = acpi_arch_timer_mem_init(timers, &timer_count);
+	if (ret || !timer_count)
+		goto out;
+
+	for (i = 0; i < timer_count; i++) {
+		ret = arch_timer_mem_verify_cntfrq(&timers[i]);
+		if (ret) {
+			pr_err("Disabling MMIO timers due to CNTFRQ mismatch\n");
+			goto out;
+		}
+	}
+
+	/*
+	 * While unlikely, it's theoretically possible that none of the frames
+	 * in a timer expose the combination of feature we want.
+	 */
+	for (i = i; i < timer_count; i++) {
+		timer = &timers[i];
+
+		frame = arch_timer_mem_find_best_frame(timer);
+		if (frame)
+			break;
+	}
+
+	if (frame)
+		ret = arch_timer_mem_frame_register(frame);
+out:
+	kfree(timers);
+	return ret;
+}
+
+/* Initialize per-processor generic timer and memory-mapped timer(if present) */
 static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 {
-	int ret;
+	int ret, platform_timer_count;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
 		pr_warn("already initialized, skipping\n");
@@ -1397,7 +1465,7 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 
 	arch_timers_present |= ARCH_TIMER_TYPE_CP15;
 
-	ret = acpi_gtdt_init(table, NULL);
+	ret = acpi_gtdt_init(table, &platform_timer_count);
 	if (ret) {
 		pr_err("Failed to init GTDT table.\n");
 		return ret;
@@ -1440,6 +1508,10 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 	if (ret)
 		return ret;
 
+	if (platform_timer_count &&
+	    arch_timer_mem_acpi_init(platform_timer_count))
+		pr_err("Failed to initialize memory-mapped timer.\n");
+
 	return arch_timer_common_init();
 }
 CLOCKSOURCE_ACPI_DECLARE(arch_timer, ACPI_SIG_GTDT, arch_timer_acpi_init);
-- 
2.9.3


^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 10/11] clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
@ 2017-04-14 18:40   ` fu.wei at linaro.org
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

The patch add memory-mapped timer register support by using the
information provided by the new GTDT driver of ACPI.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: verify CNTFRQ, only register the first frame]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/clocksource/arm_arch_timer.c | 78 ++++++++++++++++++++++++++++++++++--
 1 file changed, 75 insertions(+), 3 deletions(-)

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 05f2f7a..8981173 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -1385,10 +1385,78 @@ CLOCKSOURCE_OF_DECLARE(armv7_arch_timer_mem, "arm,armv7-timer-mem",
 		       arch_timer_mem_of_init);
 
 #ifdef CONFIG_ACPI_GTDT
-/* Initialize per-processor generic timer */
+static int __init
+arch_timer_mem_verify_cntfrq(struct arch_timer_mem *timer_mem)
+{
+	struct arch_timer_mem_frame *frame;
+	u32 rate;
+	int i;
+
+	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
+		frame = &timer_mem->frame[i];
+
+		if (!frame->valid)
+			continue;
+
+		rate = arch_timer_mem_frame_get_cntfrq(frame);
+		if (rate == arch_timer_rate)
+			continue;
+
+		pr_err(FW_BUG "CNTFRQ mismatch: frame @ %pa: (0x%08lx), CPU: (0x%08lx)\n",
+		       &frame->cntbase,
+		       (unsigned long)rate, (unsigned long)arch_timer_rate);
+
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int __init arch_timer_mem_acpi_init(int platform_timer_count)
+{
+	struct arch_timer_mem *timers, *timer;
+	struct arch_timer_mem_frame *frame;
+	int timer_count, i, ret = 0;
+
+	timers = kcalloc(platform_timer_count, sizeof(*timers), GFP_KERNEL);
+	if (!timers)
+		return -ENOMEM;
+
+	ret = acpi_arch_timer_mem_init(timers, &timer_count);
+	if (ret || !timer_count)
+		goto out;
+
+	for (i = 0; i < timer_count; i++) {
+		ret = arch_timer_mem_verify_cntfrq(&timers[i]);
+		if (ret) {
+			pr_err("Disabling MMIO timers due to CNTFRQ mismatch\n");
+			goto out;
+		}
+	}
+
+	/*
+	 * While unlikely, it's theoretically possible that none of the frames
+	 * in a timer expose the combination of feature we want.
+	 */
+	for (i = i; i < timer_count; i++) {
+		timer = &timers[i];
+
+		frame = arch_timer_mem_find_best_frame(timer);
+		if (frame)
+			break;
+	}
+
+	if (frame)
+		ret = arch_timer_mem_frame_register(frame);
+out:
+	kfree(timers);
+	return ret;
+}
+
+/* Initialize per-processor generic timer and memory-mapped timer(if present) */
 static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 {
-	int ret;
+	int ret, platform_timer_count;
 
 	if (arch_timers_present & ARCH_TIMER_TYPE_CP15) {
 		pr_warn("already initialized, skipping\n");
@@ -1397,7 +1465,7 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 
 	arch_timers_present |= ARCH_TIMER_TYPE_CP15;
 
-	ret = acpi_gtdt_init(table, NULL);
+	ret = acpi_gtdt_init(table, &platform_timer_count);
 	if (ret) {
 		pr_err("Failed to init GTDT table.\n");
 		return ret;
@@ -1440,6 +1508,10 @@ static int __init arch_timer_acpi_init(struct acpi_table_header *table)
 	if (ret)
 		return ret;
 
+	if (platform_timer_count &&
+	    arch_timer_mem_acpi_init(platform_timer_count))
+		pr_err("Failed to initialize memory-mapped timer.\n");
+
 	return arch_timer_common_init();
 }
 CLOCKSOURCE_ACPI_DECLARE(arch_timer, ACPI_SIG_GTDT, arch_timer_acpi_init);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 11/11] acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
  2017-04-14 18:40 ` fu.wei at linaro.org
  (?)
@ 2017-04-14 18:40   ` fu.wei
  -1 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

This driver adds support for parsing SBSA Generic Watchdog timer
in GTDT, parse all info in SBSA Generic Watchdog Structure in GTDT,
and creating a platform device with that information.

This allows the operating system to obtain device data from the
resource of platform device. The platform device named "sbsa-gwdt"
can be used by the ARM SBSA Generic Watchdog driver.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/acpi/arm64/gtdt.c | 103 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 103 insertions(+)

diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
index c9ef9c2..6ba47ea 100644
--- a/drivers/acpi/arm64/gtdt.c
+++ b/drivers/acpi/arm64/gtdt.c
@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/irqdomain.h>
 #include <linux/kernel.h>
+#include <linux/platform_device.h>
 
 #include <clocksource/arm_arch_timer.h>
 
@@ -60,6 +61,17 @@ static inline bool is_timer_block(void *platform_timer)
 	return gh->type == ACPI_GTDT_TYPE_TIMER_BLOCK;
 }
 
+static inline bool is_non_secure_watchdog(void *platform_timer)
+{
+	struct acpi_gtdt_header *gh = platform_timer;
+	struct acpi_gtdt_watchdog *wd = platform_timer;
+
+	if (gh->type != ACPI_GTDT_TYPE_WATCHDOG)
+		return false;
+
+	return !(wd->timer_flags & ACPI_GTDT_WATCHDOG_SECURE);
+}
+
 static int __init map_gt_gsi(u32 interrupt, u32 flags)
 {
 	int trigger, polarity;
@@ -299,3 +311,94 @@ int __init acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem,
 
 	return 0;
 }
+
+/*
+ * Initialize a SBSA generic Watchdog platform device info from GTDT
+ */
+static int __init gtdt_import_sbsa_gwdt(struct acpi_gtdt_watchdog *wd,
+					int index)
+{
+	struct platform_device *pdev;
+	int irq = map_gt_gsi(wd->timer_interrupt, wd->timer_flags);
+
+	/*
+	 * According to SBSA specification the size of refresh and control
+	 * frames of SBSA Generic Watchdog is SZ_4K(Offset 0x000 – 0xFFF).
+	 */
+	struct resource res[] = {
+		DEFINE_RES_MEM(wd->control_frame_address, SZ_4K),
+		DEFINE_RES_MEM(wd->refresh_frame_address, SZ_4K),
+		DEFINE_RES_IRQ(irq),
+	};
+	int nr_res = ARRAY_SIZE(res);
+
+	pr_debug("found a Watchdog (0x%llx/0x%llx gsi:%u flags:0x%x).\n",
+		 wd->refresh_frame_address, wd->control_frame_address,
+		 wd->timer_interrupt, wd->timer_flags);
+
+	if (!(wd->refresh_frame_address && wd->control_frame_address)) {
+		pr_err(FW_BUG "failed to get the Watchdog base address.\n");
+		acpi_unregister_gsi(wd->timer_interrupt);
+		return -EINVAL;
+	}
+
+	if (irq <= 0) {
+		pr_warn("failed to map the Watchdog interrupt.\n");
+		nr_res--;
+	}
+
+	/*
+	 * Add a platform device named "sbsa-gwdt" to match the platform driver.
+	 * "sbsa-gwdt": SBSA(Server Base System Architecture) Generic Watchdog
+	 * The platform driver can get device info below by matching this name.
+	 */
+	pdev = platform_device_register_simple("sbsa-gwdt", index, res, nr_res);
+	if (IS_ERR(pdev)) {
+		acpi_unregister_gsi(wd->timer_interrupt);
+		return PTR_ERR(pdev);
+	}
+
+	return 0;
+}
+
+static int __init gtdt_sbsa_gwdt_init(void)
+{
+	void *platform_timer;
+	struct acpi_table_header *table;
+	int ret, timer_count, gwdt_count = 0;
+
+	if (acpi_disabled)
+		return 0;
+
+	if (ACPI_FAILURE(acpi_get_table(ACPI_SIG_GTDT, 0, &table)))
+		return -EINVAL;
+
+	/*
+	 * Note: Even though the global variable acpi_gtdt_desc has been
+	 * initialized by acpi_gtdt_init() while initializing the arch timers,
+	 * when we call this function to get SBSA watchdogs info from GTDT, the
+	 * pointers stashed in it are stale (since they are early temporary
+	 * mappings carried out before acpi_permanent_mmap is set) and we need
+	 * to re-initialize them with permanent mapped pointer values to let the
+	 * GTDT parsing possible.
+	 */
+	ret = acpi_gtdt_init(table, &timer_count);
+	if (ret || !timer_count)
+		return ret;
+
+	for_each_platform_timer(platform_timer) {
+		if (is_non_secure_watchdog(platform_timer)) {
+			ret = gtdt_import_sbsa_gwdt(platform_timer, gwdt_count);
+			if (ret)
+				break;
+			gwdt_count++;
+		}
+	}
+
+	if (gwdt_count)
+		pr_info("found %d SBSA generic Watchdog(s).\n", gwdt_count);
+
+	return ret;
+}
+
+device_initcall(gtdt_sbsa_gwdt_init);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 11/11] acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
@ 2017-04-14 18:40   ` fu.wei
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei @ 2017-04-14 18:40 UTC (permalink / raw)
  To: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	lorenzo.pieralisi, sudeep.holla, hanjun.guo
  Cc: linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall, Fu Wei

From: Fu Wei <fu.wei@linaro.org>

This driver adds support for parsing SBSA Generic Watchdog timer
in GTDT, parse all info in SBSA Generic Watchdog Structure in GTDT,
and creating a platform device with that information.

This allows the operating system to obtain device data from the
resource of platform device. The platform device named "sbsa-gwdt"
can be used by the ARM SBSA Generic Watchdog driver.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/acpi/arm64/gtdt.c | 103 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 103 insertions(+)

diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
index c9ef9c2..6ba47ea 100644
--- a/drivers/acpi/arm64/gtdt.c
+++ b/drivers/acpi/arm64/gtdt.c
@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/irqdomain.h>
 #include <linux/kernel.h>
+#include <linux/platform_device.h>
 
 #include <clocksource/arm_arch_timer.h>
 
@@ -60,6 +61,17 @@ static inline bool is_timer_block(void *platform_timer)
 	return gh->type == ACPI_GTDT_TYPE_TIMER_BLOCK;
 }
 
+static inline bool is_non_secure_watchdog(void *platform_timer)
+{
+	struct acpi_gtdt_header *gh = platform_timer;
+	struct acpi_gtdt_watchdog *wd = platform_timer;
+
+	if (gh->type != ACPI_GTDT_TYPE_WATCHDOG)
+		return false;
+
+	return !(wd->timer_flags & ACPI_GTDT_WATCHDOG_SECURE);
+}
+
 static int __init map_gt_gsi(u32 interrupt, u32 flags)
 {
 	int trigger, polarity;
@@ -299,3 +311,94 @@ int __init acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem,
 
 	return 0;
 }
+
+/*
+ * Initialize a SBSA generic Watchdog platform device info from GTDT
+ */
+static int __init gtdt_import_sbsa_gwdt(struct acpi_gtdt_watchdog *wd,
+					int index)
+{
+	struct platform_device *pdev;
+	int irq = map_gt_gsi(wd->timer_interrupt, wd->timer_flags);
+
+	/*
+	 * According to SBSA specification the size of refresh and control
+	 * frames of SBSA Generic Watchdog is SZ_4K(Offset 0x000 – 0xFFF).
+	 */
+	struct resource res[] = {
+		DEFINE_RES_MEM(wd->control_frame_address, SZ_4K),
+		DEFINE_RES_MEM(wd->refresh_frame_address, SZ_4K),
+		DEFINE_RES_IRQ(irq),
+	};
+	int nr_res = ARRAY_SIZE(res);
+
+	pr_debug("found a Watchdog (0x%llx/0x%llx gsi:%u flags:0x%x).\n",
+		 wd->refresh_frame_address, wd->control_frame_address,
+		 wd->timer_interrupt, wd->timer_flags);
+
+	if (!(wd->refresh_frame_address && wd->control_frame_address)) {
+		pr_err(FW_BUG "failed to get the Watchdog base address.\n");
+		acpi_unregister_gsi(wd->timer_interrupt);
+		return -EINVAL;
+	}
+
+	if (irq <= 0) {
+		pr_warn("failed to map the Watchdog interrupt.\n");
+		nr_res--;
+	}
+
+	/*
+	 * Add a platform device named "sbsa-gwdt" to match the platform driver.
+	 * "sbsa-gwdt": SBSA(Server Base System Architecture) Generic Watchdog
+	 * The platform driver can get device info below by matching this name.
+	 */
+	pdev = platform_device_register_simple("sbsa-gwdt", index, res, nr_res);
+	if (IS_ERR(pdev)) {
+		acpi_unregister_gsi(wd->timer_interrupt);
+		return PTR_ERR(pdev);
+	}
+
+	return 0;
+}
+
+static int __init gtdt_sbsa_gwdt_init(void)
+{
+	void *platform_timer;
+	struct acpi_table_header *table;
+	int ret, timer_count, gwdt_count = 0;
+
+	if (acpi_disabled)
+		return 0;
+
+	if (ACPI_FAILURE(acpi_get_table(ACPI_SIG_GTDT, 0, &table)))
+		return -EINVAL;
+
+	/*
+	 * Note: Even though the global variable acpi_gtdt_desc has been
+	 * initialized by acpi_gtdt_init() while initializing the arch timers,
+	 * when we call this function to get SBSA watchdogs info from GTDT, the
+	 * pointers stashed in it are stale (since they are early temporary
+	 * mappings carried out before acpi_permanent_mmap is set) and we need
+	 * to re-initialize them with permanent mapped pointer values to let the
+	 * GTDT parsing possible.
+	 */
+	ret = acpi_gtdt_init(table, &timer_count);
+	if (ret || !timer_count)
+		return ret;
+
+	for_each_platform_timer(platform_timer) {
+		if (is_non_secure_watchdog(platform_timer)) {
+			ret = gtdt_import_sbsa_gwdt(platform_timer, gwdt_count);
+			if (ret)
+				break;
+			gwdt_count++;
+		}
+	}
+
+	if (gwdt_count)
+		pr_info("found %d SBSA generic Watchdog(s).\n", gwdt_count);
+
+	return ret;
+}
+
+device_initcall(gtdt_sbsa_gwdt_init);
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* [PATCH v24 11/11] acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
@ 2017-04-14 18:40   ` fu.wei
  0 siblings, 0 replies; 41+ messages in thread
From: fu.wei at linaro.org @ 2017-04-14 18:40 UTC (permalink / raw)
  To: linux-arm-kernel

From: Fu Wei <fu.wei@linaro.org>

This driver adds support for parsing SBSA Generic Watchdog timer
in GTDT, parse all info in SBSA Generic Watchdog Structure in GTDT,
and creating a platform device with that information.

This allows the operating system to obtain device data from the
resource of platform device. The platform device named "sbsa-gwdt"
can be used by the ARM SBSA Generic Watchdog driver.

Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/acpi/arm64/gtdt.c | 103 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 103 insertions(+)

diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
index c9ef9c2..6ba47ea 100644
--- a/drivers/acpi/arm64/gtdt.c
+++ b/drivers/acpi/arm64/gtdt.c
@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/irqdomain.h>
 #include <linux/kernel.h>
+#include <linux/platform_device.h>
 
 #include <clocksource/arm_arch_timer.h>
 
@@ -60,6 +61,17 @@ static inline bool is_timer_block(void *platform_timer)
 	return gh->type == ACPI_GTDT_TYPE_TIMER_BLOCK;
 }
 
+static inline bool is_non_secure_watchdog(void *platform_timer)
+{
+	struct acpi_gtdt_header *gh = platform_timer;
+	struct acpi_gtdt_watchdog *wd = platform_timer;
+
+	if (gh->type != ACPI_GTDT_TYPE_WATCHDOG)
+		return false;
+
+	return !(wd->timer_flags & ACPI_GTDT_WATCHDOG_SECURE);
+}
+
 static int __init map_gt_gsi(u32 interrupt, u32 flags)
 {
 	int trigger, polarity;
@@ -299,3 +311,94 @@ int __init acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem,
 
 	return 0;
 }
+
+/*
+ * Initialize a SBSA generic Watchdog platform device info from GTDT
+ */
+static int __init gtdt_import_sbsa_gwdt(struct acpi_gtdt_watchdog *wd,
+					int index)
+{
+	struct platform_device *pdev;
+	int irq = map_gt_gsi(wd->timer_interrupt, wd->timer_flags);
+
+	/*
+	 * According to SBSA specification the size of refresh and control
+	 * frames of SBSA Generic Watchdog is SZ_4K(Offset 0x000 ? 0xFFF).
+	 */
+	struct resource res[] = {
+		DEFINE_RES_MEM(wd->control_frame_address, SZ_4K),
+		DEFINE_RES_MEM(wd->refresh_frame_address, SZ_4K),
+		DEFINE_RES_IRQ(irq),
+	};
+	int nr_res = ARRAY_SIZE(res);
+
+	pr_debug("found a Watchdog (0x%llx/0x%llx gsi:%u flags:0x%x).\n",
+		 wd->refresh_frame_address, wd->control_frame_address,
+		 wd->timer_interrupt, wd->timer_flags);
+
+	if (!(wd->refresh_frame_address && wd->control_frame_address)) {
+		pr_err(FW_BUG "failed to get the Watchdog base address.\n");
+		acpi_unregister_gsi(wd->timer_interrupt);
+		return -EINVAL;
+	}
+
+	if (irq <= 0) {
+		pr_warn("failed to map the Watchdog interrupt.\n");
+		nr_res--;
+	}
+
+	/*
+	 * Add a platform device named "sbsa-gwdt" to match the platform driver.
+	 * "sbsa-gwdt": SBSA(Server Base System Architecture) Generic Watchdog
+	 * The platform driver can get device info below by matching this name.
+	 */
+	pdev = platform_device_register_simple("sbsa-gwdt", index, res, nr_res);
+	if (IS_ERR(pdev)) {
+		acpi_unregister_gsi(wd->timer_interrupt);
+		return PTR_ERR(pdev);
+	}
+
+	return 0;
+}
+
+static int __init gtdt_sbsa_gwdt_init(void)
+{
+	void *platform_timer;
+	struct acpi_table_header *table;
+	int ret, timer_count, gwdt_count = 0;
+
+	if (acpi_disabled)
+		return 0;
+
+	if (ACPI_FAILURE(acpi_get_table(ACPI_SIG_GTDT, 0, &table)))
+		return -EINVAL;
+
+	/*
+	 * Note: Even though the global variable acpi_gtdt_desc has been
+	 * initialized by acpi_gtdt_init() while initializing the arch timers,
+	 * when we call this function to get SBSA watchdogs info from GTDT, the
+	 * pointers stashed in it are stale (since they are early temporary
+	 * mappings carried out before acpi_permanent_mmap is set) and we need
+	 * to re-initialize them with permanent mapped pointer values to let the
+	 * GTDT parsing possible.
+	 */
+	ret = acpi_gtdt_init(table, &timer_count);
+	if (ret || !timer_count)
+		return ret;
+
+	for_each_platform_timer(platform_timer) {
+		if (is_non_secure_watchdog(platform_timer)) {
+			ret = gtdt_import_sbsa_gwdt(platform_timer, gwdt_count);
+			if (ret)
+				break;
+			gwdt_count++;
+		}
+	}
+
+	if (gwdt_count)
+		pr_info("found %d SBSA generic Watchdog(s).\n", gwdt_count);
+
+	return ret;
+}
+
+device_initcall(gtdt_sbsa_gwdt_init);
-- 
2.9.3

^ permalink raw reply related	[flat|nested] 41+ messages in thread

* Re: [PATCH v24 08/11] acpi: Introduce acpi_unregister_irq function
  2017-04-14 18:40   ` fu.wei at linaro.org
@ 2017-04-18 15:58     ` Mark Rutland
  -1 siblings, 0 replies; 41+ messages in thread
From: Mark Rutland @ 2017-04-18 15:58 UTC (permalink / raw)
  To: fu.wei, rjw, lenb, lorenzo.pieralisi, hanjun.guo
  Cc: daniel.lezcano, tglx, marc.zyngier, sudeep.holla,
	linux-arm-kernel, linaro-acpi, linux-kernel, linux-acpi,
	rruigrok, harba, cov, timur, graeme.gregory, al.stone, jcm, wei,
	arnd, catalin.marinas, will.deacon, Suravee.Suthikulpanit,
	leo.duran, wim, linux, linux-watchdog, tn, christoffer.dall,
	julien.grall

On Sat, Apr 15, 2017 at 02:40:11AM +0800, fu.wei@linaro.org wrote:
> From: Fu Wei <fu.wei@linaro.org>
> 
> This patch introduces acpi_unregister_irq function to free a
> linux IRQ number<->GSI mapping by a given linux IRQ number.
> 
> Even we have successfully registered the GSI, when some error occurs, we
> may need to unmap it for freeing the IRQ resource. But in some cases, we
> only have IRQ, but not GSI.
> 
> This patch is the preparation for memory-mapped timer support in GTDT
> driver.
> 
> Signed-off-by: Fu Wei <fu.wei@linaro.org>
> ---
>  drivers/acpi/irq.c   | 10 ++++++++++
>  include/linux/acpi.h |  7 +++++++
>  2 files changed, 17 insertions(+)

This will need comments/acks from the ACPI folk.

Lorenzo, do you prefer this to direct use of irq_dispose_mapping() in
the GTDT parsing code?

Thanks,
Mark.

> diff --git a/drivers/acpi/irq.c b/drivers/acpi/irq.c
> index 830299a..59de777 100644
> --- a/drivers/acpi/irq.c
> +++ b/drivers/acpi/irq.c
> @@ -85,6 +85,16 @@ void acpi_unregister_gsi(u32 gsi)
>  EXPORT_SYMBOL_GPL(acpi_unregister_gsi);
>  
>  /**
> + * acpi_unregister_irq() - Free a linux IRQ number<->GSI mapping
> + * @irq: linux IRQ number
> + */
> +void acpi_unregister_irq(int irq)
> +{
> +	irq_dispose_mapping(irq);
> +}
> +EXPORT_SYMBOL_GPL(acpi_unregister_irq);
> +
> +/**
>   * acpi_get_irq_source_fwhandle() - Retrieve fwhandle from IRQ resource source.
>   * @source: acpi_resource_source to use for the lookup.
>   *
> diff --git a/include/linux/acpi.h b/include/linux/acpi.h
> index 4b5c146..728d1ed 100644
> --- a/include/linux/acpi.h
> +++ b/include/linux/acpi.h
> @@ -336,6 +336,13 @@ extern int acpi_get_override_irq(u32 gsi, int *trigger, int *polarity);
>   */
>  void acpi_unregister_gsi (u32 gsi);
>  
> +/*
> + * This function undoes the effect of one call to acpi_register_gsi().
> + * The irq should be the return value of acpi_register_gsi().
> + * If the irq is valid, free a linux IRQ number<->GSI mapping.
> + */
> +void acpi_unregister_irq(int irq);
> +
>  struct pci_dev;
>  
>  int acpi_pci_irq_enable (struct pci_dev *dev);
> -- 
> 2.9.3
> 

^ permalink raw reply	[flat|nested] 41+ messages in thread

* [PATCH v24 08/11] acpi: Introduce acpi_unregister_irq function
@ 2017-04-18 15:58     ` Mark Rutland
  0 siblings, 0 replies; 41+ messages in thread
From: Mark Rutland @ 2017-04-18 15:58 UTC (permalink / raw)
  To: linux-arm-kernel

On Sat, Apr 15, 2017 at 02:40:11AM +0800, fu.wei at linaro.org wrote:
> From: Fu Wei <fu.wei@linaro.org>
> 
> This patch introduces acpi_unregister_irq function to free a
> linux IRQ number<->GSI mapping by a given linux IRQ number.
> 
> Even we have successfully registered the GSI, when some error occurs, we
> may need to unmap it for freeing the IRQ resource. But in some cases, we
> only have IRQ, but not GSI.
> 
> This patch is the preparation for memory-mapped timer support in GTDT
> driver.
> 
> Signed-off-by: Fu Wei <fu.wei@linaro.org>
> ---
>  drivers/acpi/irq.c   | 10 ++++++++++
>  include/linux/acpi.h |  7 +++++++
>  2 files changed, 17 insertions(+)

This will need comments/acks from the ACPI folk.

Lorenzo, do you prefer this to direct use of irq_dispose_mapping() in
the GTDT parsing code?

Thanks,
Mark.

> diff --git a/drivers/acpi/irq.c b/drivers/acpi/irq.c
> index 830299a..59de777 100644
> --- a/drivers/acpi/irq.c
> +++ b/drivers/acpi/irq.c
> @@ -85,6 +85,16 @@ void acpi_unregister_gsi(u32 gsi)
>  EXPORT_SYMBOL_GPL(acpi_unregister_gsi);
>  
>  /**
> + * acpi_unregister_irq() - Free a linux IRQ number<->GSI mapping
> + * @irq: linux IRQ number
> + */
> +void acpi_unregister_irq(int irq)
> +{
> +	irq_dispose_mapping(irq);
> +}
> +EXPORT_SYMBOL_GPL(acpi_unregister_irq);
> +
> +/**
>   * acpi_get_irq_source_fwhandle() - Retrieve fwhandle from IRQ resource source.
>   * @source: acpi_resource_source to use for the lookup.
>   *
> diff --git a/include/linux/acpi.h b/include/linux/acpi.h
> index 4b5c146..728d1ed 100644
> --- a/include/linux/acpi.h
> +++ b/include/linux/acpi.h
> @@ -336,6 +336,13 @@ extern int acpi_get_override_irq(u32 gsi, int *trigger, int *polarity);
>   */
>  void acpi_unregister_gsi (u32 gsi);
>  
> +/*
> + * This function undoes the effect of one call to acpi_register_gsi().
> + * The irq should be the return value of acpi_register_gsi().
> + * If the irq is valid, free a linux IRQ number<->GSI mapping.
> + */
> +void acpi_unregister_irq(int irq);
> +
>  struct pci_dev;
>  
>  int acpi_pci_irq_enable (struct pci_dev *dev);
> -- 
> 2.9.3
> 

^ permalink raw reply	[flat|nested] 41+ messages in thread

* Re: [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
  2017-04-14 18:40   ` fu.wei at linaro.org
@ 2017-04-18 17:21     ` Lorenzo Pieralisi
  -1 siblings, 0 replies; 41+ messages in thread
From: Lorenzo Pieralisi @ 2017-04-18 17:21 UTC (permalink / raw)
  To: fu.wei
  Cc: rjw, lenb, daniel.lezcano, tglx, marc.zyngier, mark.rutland,
	sudeep.holla, hanjun.guo, linux-arm-kernel, linaro-acpi,
	linux-kernel, linux-acpi, rruigrok, harba, cov, timur,
	graeme.gregory, al.stone, jcm, wei, arnd, catalin.marinas,
	will.deacon, Suravee.Suthikulpanit, leo.duran, wim, linux,
	linux-watchdog, tn, christoffer.dall, julien.grall

On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei@linaro.org wrote:
> From: Fu Wei <fu.wei@linaro.org>
> 
> On platforms booting with ACPI, architected memory-mapped timers'
> configuration data is provided by firmware through the ACPI GTDT
> static table.
> 
> The clocksource architected timer kernel driver requires a firmware
> interface to collect timer configuration and configure its driver.
> this infrastructure is present for device tree systems, but it is
> missing on systems booting with ACPI.
> 
> Implement the kernel infrastructure required to parse the static
> ACPI GTDT table so that the architected timer clocksource driver can
> make use of it on systems booting with ACPI, therefore enabling
> the corresponding timers configuration.
> 
> Signed-off-by: Fu Wei <fu.wei@linaro.org>
> Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
> Signed-off-by: Mark Rutland <mark.rutland@arm.com>
> ---
>  drivers/acpi/arm64/gtdt.c | 144 ++++++++++++++++++++++++++++++++++++++++++++++
>  include/linux/acpi.h      |   1 +
>  2 files changed, 145 insertions(+)
> 
> diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
> index 3d95af8..c9ef9c2 100644
> --- a/drivers/acpi/arm64/gtdt.c
> +++ b/drivers/acpi/arm64/gtdt.c
> @@ -13,6 +13,7 @@
>  
>  #include <linux/acpi.h>
>  #include <linux/init.h>
> +#include <linux/irqdomain.h>
>  #include <linux/kernel.h>
>  
>  #include <clocksource/arm_arch_timer.h>
> @@ -37,6 +38,28 @@ struct acpi_gtdt_descriptor {
>  
>  static struct acpi_gtdt_descriptor acpi_gtdt_desc __initdata;
>  
> +static inline void *next_platform_timer(void *platform_timer)
> +{
> +	struct acpi_gtdt_header *gh = platform_timer;
> +
> +	platform_timer += gh->length;
> +	if (platform_timer < acpi_gtdt_desc.gtdt_end)
> +		return platform_timer;
> +
> +	return NULL;
> +}
> +
> +#define for_each_platform_timer(_g)				\
> +	for (_g = acpi_gtdt_desc.platform_timer; _g;	\
> +	     _g = next_platform_timer(_g))
> +
> +static inline bool is_timer_block(void *platform_timer)
> +{
> +	struct acpi_gtdt_header *gh = platform_timer;
> +
> +	return gh->type == ACPI_GTDT_TYPE_TIMER_BLOCK;
> +}
> +
>  static int __init map_gt_gsi(u32 interrupt, u32 flags)
>  {
>  	int trigger, polarity;
> @@ -155,3 +178,124 @@ int __init acpi_gtdt_init(struct acpi_table_header *table,
>  
>  	return 0;
>  }
> +
> +static int __init gtdt_parse_timer_block(struct acpi_gtdt_timer_block *block,
> +					 struct arch_timer_mem *timer_mem)
> +{
> +	int i;
> +	struct arch_timer_mem_frame *frame;
> +	struct acpi_gtdt_timer_entry *gtdt_frame;
> +
> +	if (!block->timer_count) {
> +		pr_err(FW_BUG "GT block present, but frame count is zero.");
> +		return -ENODEV;
> +	}
> +
> +	if (block->timer_count > ARCH_TIMER_MEM_MAX_FRAMES) {
> +		pr_err(FW_BUG "GT block lists %d frames, ACPI spec only allows 8\n",
> +		       block->timer_count);
> +		return -EINVAL;
> +	}
> +
> +	timer_mem->cntctlbase = (phys_addr_t)block->block_address;
> +	/*
> +	 * The CNTCTLBase frame is 4KB (register offsets 0x000 - 0xFFC).
> +	 * See ARM DDI 0487A.k_iss10775, page I1-5129, Table I1-3
> +	 * "CNTCTLBase memory map".
> +	 */
> +	timer_mem->size = SZ_4K;
> +
> +	gtdt_frame = (void *)block + block->timer_offset;
> +	if (gtdt_frame + block->timer_count != (void *)block + block->header.length)
> +		return -EINVAL;
> +
> +	/*
> +	 * Get the GT timer Frame data for every GT Block Timer
> +	 */
> +	for (i = 0; i < block->timer_count; i++, gtdt_frame++) {
> +		if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> +			continue;
> +
> +		if (!gtdt_frame->base_address || !gtdt_frame->timer_interrupt)
> +			goto error;
> +
> +		frame = &timer_mem->frame[gtdt_frame->frame_number];
> +		frame->phys_irq = map_gt_gsi(gtdt_frame->timer_interrupt,
> +					     gtdt_frame->timer_flags);
> +		if (frame->phys_irq <= 0) {
> +			pr_warn("failed to map physical timer irq in frame %d.\n",
> +				gtdt_frame->frame_number);
> +			goto error;
> +		}
> +
> +		if (gtdt_frame->virtual_timer_interrupt) {
> +			frame->virt_irq =
> +				map_gt_gsi(gtdt_frame->virtual_timer_interrupt,
> +					   gtdt_frame->virtual_timer_flags);
> +			if (frame->virt_irq <= 0) {
> +				pr_warn("failed to map virtual timer irq in frame %d.\n",
> +					gtdt_frame->frame_number);
> +				goto error;
> +			}
> +		} else {
> +			frame->virt_irq = 0;
> +			pr_debug("virtual timer in frame %d not implemented.\n",
> +				 gtdt_frame->frame_number);
> +		}
> +
> +		frame->cntbase = gtdt_frame->base_address;
> +		/*
> +		 * The CNTBaseN frame is 4KB (register offsets 0x000 - 0xFFC).
> +		 * See ARM DDI 0487A.k_iss10775, page I1-5130, Table I1-4
> +		 * "CNTBaseN memory map".
> +		 */
> +		frame->size = SZ_4K;
> +		frame->valid = true;
> +	}
> +
> +	return 0;
> +
> +error:
> +	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
> +		frame = &timer_mem->frame[i];
> +		if (frame->phys_irq > 0)
> +			acpi_unregister_irq(frame->phys_irq);
> +		if (frame->virt_irq > 0)
> +			acpi_unregister_irq(frame->virt_irq);
> +	}

There are three error paths, none of them reset [i,gtdt_frame],
correct ?

If yes, why can't it simply be written like this ?

for (; i >= 0; i--, gtdt_frame--) {
	frame = &timer_mem->frame[gtdt_frame->frame_number];

	/* not sure this check is actually needed */
	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
		continue;

	if (frame->phys_irq > 0)
		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
	if (frame->virt_irq > 0)
		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
}

It is time we merged this code, that's for certain so if for any reason
loop above does not work this current series is ok for me, go ahead, I
just don't see the point of adding another ACPI IRQ function
acpi_unregister_irq() (which does not mean acpi_unregister_gsi() is sane
- we just lived with it when ACPI ARM64 was merged because changing its
API requires reworking x86 legacy code that I don't understand).

Thanks,
Lorenzo

> +	return -EINVAL;
> +}
> +
> +/**
> + * acpi_arch_timer_mem_init() - Get the info of all GT blocks in GTDT table.
> + * @timer_mem:	The pointer to the array of struct arch_timer_mem for returning
> + *		the result of parsing. The element number of this array should
> + *		be platform_timer_count(the total number of platform timers).
> + * @timer_count: It points to a integer variable which is used for storing the
> + *		number of GT blocks we have parsed.
> + *
> + * Return: 0 if success, -EINVAL/-ENODEV if error.
> + */
> +int __init acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem,
> +				    int *timer_count)
> +{
> +	int ret;
> +	void *platform_timer;
> +
> +	*timer_count = 0;
> +	for_each_platform_timer(platform_timer) {
> +		if (is_timer_block(platform_timer)) {
> +			ret = gtdt_parse_timer_block(platform_timer, timer_mem);
> +			if (ret)
> +				return ret;
> +			timer_mem++;
> +			(*timer_count)++;
> +		}
> +	}
> +
> +	if (*timer_count)
> +		pr_info("found %d memory-mapped timer block(s).\n",
> +			*timer_count);
> +
> +	return 0;
> +}
> diff --git a/include/linux/acpi.h b/include/linux/acpi.h
> index 728d1ed..4b1ab65 100644
> --- a/include/linux/acpi.h
> +++ b/include/linux/acpi.h
> @@ -606,6 +606,7 @@ int acpi_reconfig_notifier_unregister(struct notifier_block *nb);
>  int acpi_gtdt_init(struct acpi_table_header *table, int *platform_timer_count);
>  int acpi_gtdt_map_ppi(int type);
>  bool acpi_gtdt_c3stop(int type);
> +int acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem, int *timer_count);
>  #endif
>  
>  #else	/* !CONFIG_ACPI */
> -- 
> 2.9.3
> 

^ permalink raw reply	[flat|nested] 41+ messages in thread

* [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
@ 2017-04-18 17:21     ` Lorenzo Pieralisi
  0 siblings, 0 replies; 41+ messages in thread
From: Lorenzo Pieralisi @ 2017-04-18 17:21 UTC (permalink / raw)
  To: linux-arm-kernel

On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei at linaro.org wrote:
> From: Fu Wei <fu.wei@linaro.org>
> 
> On platforms booting with ACPI, architected memory-mapped timers'
> configuration data is provided by firmware through the ACPI GTDT
> static table.
> 
> The clocksource architected timer kernel driver requires a firmware
> interface to collect timer configuration and configure its driver.
> this infrastructure is present for device tree systems, but it is
> missing on systems booting with ACPI.
> 
> Implement the kernel infrastructure required to parse the static
> ACPI GTDT table so that the architected timer clocksource driver can
> make use of it on systems booting with ACPI, therefore enabling
> the corresponding timers configuration.
> 
> Signed-off-by: Fu Wei <fu.wei@linaro.org>
> Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
> Signed-off-by: Mark Rutland <mark.rutland@arm.com>
> ---
>  drivers/acpi/arm64/gtdt.c | 144 ++++++++++++++++++++++++++++++++++++++++++++++
>  include/linux/acpi.h      |   1 +
>  2 files changed, 145 insertions(+)
> 
> diff --git a/drivers/acpi/arm64/gtdt.c b/drivers/acpi/arm64/gtdt.c
> index 3d95af8..c9ef9c2 100644
> --- a/drivers/acpi/arm64/gtdt.c
> +++ b/drivers/acpi/arm64/gtdt.c
> @@ -13,6 +13,7 @@
>  
>  #include <linux/acpi.h>
>  #include <linux/init.h>
> +#include <linux/irqdomain.h>
>  #include <linux/kernel.h>
>  
>  #include <clocksource/arm_arch_timer.h>
> @@ -37,6 +38,28 @@ struct acpi_gtdt_descriptor {
>  
>  static struct acpi_gtdt_descriptor acpi_gtdt_desc __initdata;
>  
> +static inline void *next_platform_timer(void *platform_timer)
> +{
> +	struct acpi_gtdt_header *gh = platform_timer;
> +
> +	platform_timer += gh->length;
> +	if (platform_timer < acpi_gtdt_desc.gtdt_end)
> +		return platform_timer;
> +
> +	return NULL;
> +}
> +
> +#define for_each_platform_timer(_g)				\
> +	for (_g = acpi_gtdt_desc.platform_timer; _g;	\
> +	     _g = next_platform_timer(_g))
> +
> +static inline bool is_timer_block(void *platform_timer)
> +{
> +	struct acpi_gtdt_header *gh = platform_timer;
> +
> +	return gh->type == ACPI_GTDT_TYPE_TIMER_BLOCK;
> +}
> +
>  static int __init map_gt_gsi(u32 interrupt, u32 flags)
>  {
>  	int trigger, polarity;
> @@ -155,3 +178,124 @@ int __init acpi_gtdt_init(struct acpi_table_header *table,
>  
>  	return 0;
>  }
> +
> +static int __init gtdt_parse_timer_block(struct acpi_gtdt_timer_block *block,
> +					 struct arch_timer_mem *timer_mem)
> +{
> +	int i;
> +	struct arch_timer_mem_frame *frame;
> +	struct acpi_gtdt_timer_entry *gtdt_frame;
> +
> +	if (!block->timer_count) {
> +		pr_err(FW_BUG "GT block present, but frame count is zero.");
> +		return -ENODEV;
> +	}
> +
> +	if (block->timer_count > ARCH_TIMER_MEM_MAX_FRAMES) {
> +		pr_err(FW_BUG "GT block lists %d frames, ACPI spec only allows 8\n",
> +		       block->timer_count);
> +		return -EINVAL;
> +	}
> +
> +	timer_mem->cntctlbase = (phys_addr_t)block->block_address;
> +	/*
> +	 * The CNTCTLBase frame is 4KB (register offsets 0x000 - 0xFFC).
> +	 * See ARM DDI 0487A.k_iss10775, page I1-5129, Table I1-3
> +	 * "CNTCTLBase memory map".
> +	 */
> +	timer_mem->size = SZ_4K;
> +
> +	gtdt_frame = (void *)block + block->timer_offset;
> +	if (gtdt_frame + block->timer_count != (void *)block + block->header.length)
> +		return -EINVAL;
> +
> +	/*
> +	 * Get the GT timer Frame data for every GT Block Timer
> +	 */
> +	for (i = 0; i < block->timer_count; i++, gtdt_frame++) {
> +		if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> +			continue;
> +
> +		if (!gtdt_frame->base_address || !gtdt_frame->timer_interrupt)
> +			goto error;
> +
> +		frame = &timer_mem->frame[gtdt_frame->frame_number];
> +		frame->phys_irq = map_gt_gsi(gtdt_frame->timer_interrupt,
> +					     gtdt_frame->timer_flags);
> +		if (frame->phys_irq <= 0) {
> +			pr_warn("failed to map physical timer irq in frame %d.\n",
> +				gtdt_frame->frame_number);
> +			goto error;
> +		}
> +
> +		if (gtdt_frame->virtual_timer_interrupt) {
> +			frame->virt_irq =
> +				map_gt_gsi(gtdt_frame->virtual_timer_interrupt,
> +					   gtdt_frame->virtual_timer_flags);
> +			if (frame->virt_irq <= 0) {
> +				pr_warn("failed to map virtual timer irq in frame %d.\n",
> +					gtdt_frame->frame_number);
> +				goto error;
> +			}
> +		} else {
> +			frame->virt_irq = 0;
> +			pr_debug("virtual timer in frame %d not implemented.\n",
> +				 gtdt_frame->frame_number);
> +		}
> +
> +		frame->cntbase = gtdt_frame->base_address;
> +		/*
> +		 * The CNTBaseN frame is 4KB (register offsets 0x000 - 0xFFC).
> +		 * See ARM DDI 0487A.k_iss10775, page I1-5130, Table I1-4
> +		 * "CNTBaseN memory map".
> +		 */
> +		frame->size = SZ_4K;
> +		frame->valid = true;
> +	}
> +
> +	return 0;
> +
> +error:
> +	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
> +		frame = &timer_mem->frame[i];
> +		if (frame->phys_irq > 0)
> +			acpi_unregister_irq(frame->phys_irq);
> +		if (frame->virt_irq > 0)
> +			acpi_unregister_irq(frame->virt_irq);
> +	}

There are three error paths, none of them reset [i,gtdt_frame],
correct ?

If yes, why can't it simply be written like this ?

for (; i >= 0; i--, gtdt_frame--) {
	frame = &timer_mem->frame[gtdt_frame->frame_number];

	/* not sure this check is actually needed */
	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
		continue;

	if (frame->phys_irq > 0)
		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
	if (frame->virt_irq > 0)
		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
}

It is time we merged this code, that's for certain so if for any reason
loop above does not work this current series is ok for me, go ahead, I
just don't see the point of adding another ACPI IRQ function
acpi_unregister_irq() (which does not mean acpi_unregister_gsi() is sane
- we just lived with it when ACPI ARM64 was merged because changing its
API requires reworking x86 legacy code that I don't understand).

Thanks,
Lorenzo

> +	return -EINVAL;
> +}
> +
> +/**
> + * acpi_arch_timer_mem_init() - Get the info of all GT blocks in GTDT table.
> + * @timer_mem:	The pointer to the array of struct arch_timer_mem for returning
> + *		the result of parsing. The element number of this array should
> + *		be platform_timer_count(the total number of platform timers).
> + * @timer_count: It points to a integer variable which is used for storing the
> + *		number of GT blocks we have parsed.
> + *
> + * Return: 0 if success, -EINVAL/-ENODEV if error.
> + */
> +int __init acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem,
> +				    int *timer_count)
> +{
> +	int ret;
> +	void *platform_timer;
> +
> +	*timer_count = 0;
> +	for_each_platform_timer(platform_timer) {
> +		if (is_timer_block(platform_timer)) {
> +			ret = gtdt_parse_timer_block(platform_timer, timer_mem);
> +			if (ret)
> +				return ret;
> +			timer_mem++;
> +			(*timer_count)++;
> +		}
> +	}
> +
> +	if (*timer_count)
> +		pr_info("found %d memory-mapped timer block(s).\n",
> +			*timer_count);
> +
> +	return 0;
> +}
> diff --git a/include/linux/acpi.h b/include/linux/acpi.h
> index 728d1ed..4b1ab65 100644
> --- a/include/linux/acpi.h
> +++ b/include/linux/acpi.h
> @@ -606,6 +606,7 @@ int acpi_reconfig_notifier_unregister(struct notifier_block *nb);
>  int acpi_gtdt_init(struct acpi_table_header *table, int *platform_timer_count);
>  int acpi_gtdt_map_ppi(int type);
>  bool acpi_gtdt_c3stop(int type);
> +int acpi_arch_timer_mem_init(struct arch_timer_mem *timer_mem, int *timer_count);
>  #endif
>  
>  #else	/* !CONFIG_ACPI */
> -- 
> 2.9.3
> 

^ permalink raw reply	[flat|nested] 41+ messages in thread

* Re: [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
  2017-04-18 17:21     ` Lorenzo Pieralisi
@ 2017-04-19 15:07       ` Mark Rutland
  -1 siblings, 0 replies; 41+ messages in thread
From: Mark Rutland @ 2017-04-19 15:07 UTC (permalink / raw)
  To: Lorenzo Pieralisi
  Cc: fu.wei, rjw, lenb, daniel.lezcano, tglx, marc.zyngier,
	sudeep.holla, hanjun.guo, linux-arm-kernel, linaro-acpi,
	linux-kernel, linux-acpi, rruigrok, harba, cov, timur,
	graeme.gregory, al.stone, jcm, wei, arnd, catalin.marinas,
	will.deacon, Suravee.Suthikulpanit, leo.duran, wim, linux,
	linux-watchdog, tn, christoffer.dall, julien.grall

On Tue, Apr 18, 2017 at 06:21:07PM +0100, Lorenzo Pieralisi wrote:
> On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei@linaro.org wrote:

> > +error:
> > +	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
> > +		frame = &timer_mem->frame[i];
> > +		if (frame->phys_irq > 0)
> > +			acpi_unregister_irq(frame->phys_irq);
> > +		if (frame->virt_irq > 0)
> > +			acpi_unregister_irq(frame->virt_irq);
> > +	}
> 
> There are three error paths, none of them reset [i,gtdt_frame],
> correct ?

Correct.

> If yes, why can't it simply be written like this ?
> 
> for (; i >= 0; i--, gtdt_frame--) {
> 	frame = &timer_mem->frame[gtdt_frame->frame_number];
> 
> 	/* not sure this check is actually needed */
> 	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> 		continue;
> 
> 	if (frame->phys_irq > 0)
> 		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
> 	if (frame->virt_irq > 0)
> 		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
> }

A reverse loop of this form will work.

That requires some restructuring, and care to avoid going out of bounds
instantaneously with the gtdt_frame--, so as to not invoke nasal demons.

I've attacked this locally, and will send this out after testing. I'll
drop the new ACPI API patch.

Thanks,
Mark.

^ permalink raw reply	[flat|nested] 41+ messages in thread

* [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
@ 2017-04-19 15:07       ` Mark Rutland
  0 siblings, 0 replies; 41+ messages in thread
From: Mark Rutland @ 2017-04-19 15:07 UTC (permalink / raw)
  To: linux-arm-kernel

On Tue, Apr 18, 2017 at 06:21:07PM +0100, Lorenzo Pieralisi wrote:
> On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei at linaro.org wrote:

> > +error:
> > +	for (i = 0; i < ARCH_TIMER_MEM_MAX_FRAMES; i++) {
> > +		frame = &timer_mem->frame[i];
> > +		if (frame->phys_irq > 0)
> > +			acpi_unregister_irq(frame->phys_irq);
> > +		if (frame->virt_irq > 0)
> > +			acpi_unregister_irq(frame->virt_irq);
> > +	}
> 
> There are three error paths, none of them reset [i,gtdt_frame],
> correct ?

Correct.

> If yes, why can't it simply be written like this ?
> 
> for (; i >= 0; i--, gtdt_frame--) {
> 	frame = &timer_mem->frame[gtdt_frame->frame_number];
> 
> 	/* not sure this check is actually needed */
> 	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> 		continue;
> 
> 	if (frame->phys_irq > 0)
> 		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
> 	if (frame->virt_irq > 0)
> 		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
> }

A reverse loop of this form will work.

That requires some restructuring, and care to avoid going out of bounds
instantaneously with the gtdt_frame--, so as to not invoke nasal demons.

I've attacked this locally, and will send this out after testing. I'll
drop the new ACPI API patch.

Thanks,
Mark.

^ permalink raw reply	[flat|nested] 41+ messages in thread

* Re: [PATCH v24 08/11] acpi: Introduce acpi_unregister_irq function
  2017-04-18 15:58     ` Mark Rutland
@ 2017-04-19 15:09       ` Mark Rutland
  -1 siblings, 0 replies; 41+ messages in thread
From: Mark Rutland @ 2017-04-19 15:09 UTC (permalink / raw)
  To: fu.wei, rjw, lenb, lorenzo.pieralisi, hanjun.guo
  Cc: linaro-acpi, catalin.marinas, will.deacon, rruigrok, wim, wei,
	al.stone, tn, timur, daniel.lezcano, linux-acpi, linux, harba,
	julien.grall, linux-watchdog, arnd, marc.zyngier, jcm, cov, tglx,
	linux-arm-kernel, graeme.gregory, linux-kernel, leo.duran,
	Suravee.Suthikulpanit, sudeep.holla, christoffer.dall

On Tue, Apr 18, 2017 at 04:58:41PM +0100, Mark Rutland wrote:
> On Sat, Apr 15, 2017 at 02:40:11AM +0800, fu.wei@linaro.org wrote:
> > From: Fu Wei <fu.wei@linaro.org>
> > 
> > This patch introduces acpi_unregister_irq function to free a
> > linux IRQ number<->GSI mapping by a given linux IRQ number.
> > 
> > Even we have successfully registered the GSI, when some error occurs, we
> > may need to unmap it for freeing the IRQ resource. But in some cases, we
> > only have IRQ, but not GSI.
> > 
> > This patch is the preparation for memory-mapped timer support in GTDT
> > driver.
> > 
> > Signed-off-by: Fu Wei <fu.wei@linaro.org>
> > ---
> >  drivers/acpi/irq.c   | 10 ++++++++++
> >  include/linux/acpi.h |  7 +++++++
> >  2 files changed, 17 insertions(+)
> 
> This will need comments/acks from the ACPI folk.

I've now reworked the cleanup to not require this API, and will drop
this patch.

Thanks,
Mark.

^ permalink raw reply	[flat|nested] 41+ messages in thread

* [PATCH v24 08/11] acpi: Introduce acpi_unregister_irq function
@ 2017-04-19 15:09       ` Mark Rutland
  0 siblings, 0 replies; 41+ messages in thread
From: Mark Rutland @ 2017-04-19 15:09 UTC (permalink / raw)
  To: linux-arm-kernel

On Tue, Apr 18, 2017 at 04:58:41PM +0100, Mark Rutland wrote:
> On Sat, Apr 15, 2017 at 02:40:11AM +0800, fu.wei at linaro.org wrote:
> > From: Fu Wei <fu.wei@linaro.org>
> > 
> > This patch introduces acpi_unregister_irq function to free a
> > linux IRQ number<->GSI mapping by a given linux IRQ number.
> > 
> > Even we have successfully registered the GSI, when some error occurs, we
> > may need to unmap it for freeing the IRQ resource. But in some cases, we
> > only have IRQ, but not GSI.
> > 
> > This patch is the preparation for memory-mapped timer support in GTDT
> > driver.
> > 
> > Signed-off-by: Fu Wei <fu.wei@linaro.org>
> > ---
> >  drivers/acpi/irq.c   | 10 ++++++++++
> >  include/linux/acpi.h |  7 +++++++
> >  2 files changed, 17 insertions(+)
> 
> This will need comments/acks from the ACPI folk.

I've now reworked the cleanup to not require this API, and will drop
this patch.

Thanks,
Mark.

^ permalink raw reply	[flat|nested] 41+ messages in thread

* Re: [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
  2017-04-19 15:07       ` Mark Rutland
  (?)
@ 2017-04-19 15:45         ` Mark Rutland
  -1 siblings, 0 replies; 41+ messages in thread
From: Mark Rutland @ 2017-04-19 15:45 UTC (permalink / raw)
  To: Lorenzo Pieralisi
  Cc: linaro-acpi-cunTk1MwBs8s++Sfvej+rw, catalin.marinas-5wv7dgnIgG8,
	will.deacon-5wv7dgnIgG8, rruigrok-sgV2jX0FEOL9JmXXK+q4OQ,
	wim-IQzOog9fTRqzQB+pC5nmwQ, fu.wei-QSEj5FYQhm4dnm+yROfE0A,
	wei-H+wXaHxf7aLQT0dZR+AlfA, al.stone-QSEj5FYQhm4dnm+yROfE0A,
	tn-nYOzD4b6Jr9Wk0Htik3J/w, timur-sgV2jX0FEOL9JmXXK+q4OQ,
	daniel.lezcano-QSEj5FYQhm4dnm+yROfE0A,
	linux-acpi-u79uwXL29TY76Z2rM5mHXA, linux-0h96xk9xTtrk1uMJSBkQmQ,
	lenb-DgEjT+Ai2ygdnm+yROfE0A, harba-sgV2jX0FEOL9JmXXK+q4OQ,
	julien.grall-5wv7dgnIgG8, linux-watchdog-u79uwXL29TY76Z2rM5mHXA,
	arnd-r2nGTMty4D4, marc.zyngier-5wv7dgnIgG8,
	jcm-H+wXaHxf7aLQT0dZR+AlfA, cov-sgV2jX0FEOL9JmXXK+q4OQ,
	tglx-hfZtesqFncYOwBW4kG4KsQ,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	graeme.gregory-QSEj5FYQhm4dnm+yROfE0A,
	rjw-LthD3rsA81gm4RdzfppkhA, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
	leo.duran-5C7GfCeVMHo, hanjun.guo-QSEj5FYQhm4dnm+yROfE0A,
	Suravee.Suthikulpanit-5C7GfCeVMHo, sudeep.holla-5wv7dgnIgG8,
	christoffer.dall-QSEj5FYQhm4dnm+yROfE0A

On Wed, Apr 19, 2017 at 04:07:25PM +0100, Mark Rutland wrote:
> On Tue, Apr 18, 2017 at 06:21:07PM +0100, Lorenzo Pieralisi wrote:
> > On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org wrote:
 
> > If yes, why can't it simply be written like this ?
> > 
> > for (; i >= 0; i--, gtdt_frame--) {
> > 	frame = &timer_mem->frame[gtdt_frame->frame_number];
> > 
> > 	/* not sure this check is actually needed */
> > 	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> > 		continue;
> > 
> > 	if (frame->phys_irq > 0)
> > 		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
> > 	if (frame->virt_irq > 0)
> > 		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
> > }
> 
> A reverse loop of this form will work.
> 
> That requires some restructuring, and care to avoid going out of bounds
> instantaneously with the gtdt_frame--, so as to not invoke nasal demons.
> 
> I've attacked this locally, and will send this out after testing. I'll
> drop the new ACPI API patch.

FWIW, I've set this up so the cleanup path is:

do {
        if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER ||
            gtdt_frame->frame_number >= ARCH_TIMER_MEM_MAX_FRAMES)
                continue;

        frame = &timer_mem->frame[gtdt_frame->frame_number];

        if (frame->phys_irq > 0)
                acpi_unregister_gsi(gtdt_frame->timer_interrupt);
        frame->phys_irq = 0;

        if (frame->virt_irq > 0)
                acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
        frame->virt_irq = 0;
} while (i-- >= 0 && gtdt_frame--);

... the zeroing is to account for duplicate frames, which I now check for in
the probe path (as we do for DT).

Can I take it per your comment on the prior version that with this change I can
take your ack?

I also assume that you're happy for all of the drivers/acpi/arm64/ patches in the
series to go via the clocksource tree?

Thanks,
Mark.
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 41+ messages in thread

* Re: [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
@ 2017-04-19 15:45         ` Mark Rutland
  0 siblings, 0 replies; 41+ messages in thread
From: Mark Rutland @ 2017-04-19 15:45 UTC (permalink / raw)
  To: Lorenzo Pieralisi
  Cc: linaro-acpi, catalin.marinas, will.deacon, rruigrok, wim, fu.wei,
	wei, al.stone, tn, timur, daniel.lezcano, linux-acpi, linux,
	lenb, harba, julien.grall, linux-watchdog, arnd, marc.zyngier,
	jcm, cov, tglx, linux-arm-kernel, graeme.gregory, rjw,
	linux-kernel, leo.duran, hanjun.guo, Suravee.Suthikulpanit,
	sudeep.holla, christoffer.dall

On Wed, Apr 19, 2017 at 04:07:25PM +0100, Mark Rutland wrote:
> On Tue, Apr 18, 2017 at 06:21:07PM +0100, Lorenzo Pieralisi wrote:
> > On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei@linaro.org wrote:
 
> > If yes, why can't it simply be written like this ?
> > 
> > for (; i >= 0; i--, gtdt_frame--) {
> > 	frame = &timer_mem->frame[gtdt_frame->frame_number];
> > 
> > 	/* not sure this check is actually needed */
> > 	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> > 		continue;
> > 
> > 	if (frame->phys_irq > 0)
> > 		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
> > 	if (frame->virt_irq > 0)
> > 		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
> > }
> 
> A reverse loop of this form will work.
> 
> That requires some restructuring, and care to avoid going out of bounds
> instantaneously with the gtdt_frame--, so as to not invoke nasal demons.
> 
> I've attacked this locally, and will send this out after testing. I'll
> drop the new ACPI API patch.

FWIW, I've set this up so the cleanup path is:

do {
        if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER ||
            gtdt_frame->frame_number >= ARCH_TIMER_MEM_MAX_FRAMES)
                continue;

        frame = &timer_mem->frame[gtdt_frame->frame_number];

        if (frame->phys_irq > 0)
                acpi_unregister_gsi(gtdt_frame->timer_interrupt);
        frame->phys_irq = 0;

        if (frame->virt_irq > 0)
                acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
        frame->virt_irq = 0;
} while (i-- >= 0 && gtdt_frame--);

... the zeroing is to account for duplicate frames, which I now check for in
the probe path (as we do for DT).

Can I take it per your comment on the prior version that with this change I can
take your ack?

I also assume that you're happy for all of the drivers/acpi/arm64/ patches in the
series to go via the clocksource tree?

Thanks,
Mark.

^ permalink raw reply	[flat|nested] 41+ messages in thread

* [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
@ 2017-04-19 15:45         ` Mark Rutland
  0 siblings, 0 replies; 41+ messages in thread
From: Mark Rutland @ 2017-04-19 15:45 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, Apr 19, 2017 at 04:07:25PM +0100, Mark Rutland wrote:
> On Tue, Apr 18, 2017 at 06:21:07PM +0100, Lorenzo Pieralisi wrote:
> > On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei at linaro.org wrote:
 
> > If yes, why can't it simply be written like this ?
> > 
> > for (; i >= 0; i--, gtdt_frame--) {
> > 	frame = &timer_mem->frame[gtdt_frame->frame_number];
> > 
> > 	/* not sure this check is actually needed */
> > 	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> > 		continue;
> > 
> > 	if (frame->phys_irq > 0)
> > 		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
> > 	if (frame->virt_irq > 0)
> > 		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
> > }
> 
> A reverse loop of this form will work.
> 
> That requires some restructuring, and care to avoid going out of bounds
> instantaneously with the gtdt_frame--, so as to not invoke nasal demons.
> 
> I've attacked this locally, and will send this out after testing. I'll
> drop the new ACPI API patch.

FWIW, I've set this up so the cleanup path is:

do {
        if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER ||
            gtdt_frame->frame_number >= ARCH_TIMER_MEM_MAX_FRAMES)
                continue;

        frame = &timer_mem->frame[gtdt_frame->frame_number];

        if (frame->phys_irq > 0)
                acpi_unregister_gsi(gtdt_frame->timer_interrupt);
        frame->phys_irq = 0;

        if (frame->virt_irq > 0)
                acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
        frame->virt_irq = 0;
} while (i-- >= 0 && gtdt_frame--);

... the zeroing is to account for duplicate frames, which I now check for in
the probe path (as we do for DT).

Can I take it per your comment on the prior version that with this change I can
take your ack?

I also assume that you're happy for all of the drivers/acpi/arm64/ patches in the
series to go via the clocksource tree?

Thanks,
Mark.

^ permalink raw reply	[flat|nested] 41+ messages in thread

* Re: [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
  2017-04-19 15:45         ` Mark Rutland
  (?)
@ 2017-04-19 15:56           ` Lorenzo Pieralisi
  -1 siblings, 0 replies; 41+ messages in thread
From: Lorenzo Pieralisi @ 2017-04-19 15:56 UTC (permalink / raw)
  To: Mark Rutland
  Cc: linaro-acpi-cunTk1MwBs8s++Sfvej+rw, catalin.marinas-5wv7dgnIgG8,
	will.deacon-5wv7dgnIgG8, rruigrok-sgV2jX0FEOL9JmXXK+q4OQ,
	wim-IQzOog9fTRqzQB+pC5nmwQ, fu.wei-QSEj5FYQhm4dnm+yROfE0A,
	wei-H+wXaHxf7aLQT0dZR+AlfA, al.stone-QSEj5FYQhm4dnm+yROfE0A,
	tn-nYOzD4b6Jr9Wk0Htik3J/w, timur-sgV2jX0FEOL9JmXXK+q4OQ,
	daniel.lezcano-QSEj5FYQhm4dnm+yROfE0A,
	linux-acpi-u79uwXL29TY76Z2rM5mHXA, linux-0h96xk9xTtrk1uMJSBkQmQ,
	lenb-DgEjT+Ai2ygdnm+yROfE0A, harba-sgV2jX0FEOL9JmXXK+q4OQ,
	julien.grall-5wv7dgnIgG8, linux-watchdog-u79uwXL29TY76Z2rM5mHXA,
	arnd-r2nGTMty4D4, marc.zyngier-5wv7dgnIgG8,
	jcm-H+wXaHxf7aLQT0dZR+AlfA, cov-sgV2jX0FEOL9JmXXK+q4OQ,
	tglx-hfZtesqFncYOwBW4kG4KsQ,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	graeme.gregory-QSEj5FYQhm4dnm+yROfE0A,
	rjw-LthD3rsA81gm4RdzfppkhA, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
	leo.duran-5C7GfCeVMHo, hanjun.guo-QSEj5FYQhm4dnm+yROfE0A,
	Suravee.Suthikulpanit-5C7GfCeVMHo, sudeep.holla-5wv7dgnIgG8,
	christoffer.dall-QSEj5FYQhm4dnm+yROfE0A

On Wed, Apr 19, 2017 at 04:45:54PM +0100, Mark Rutland wrote:
> On Wed, Apr 19, 2017 at 04:07:25PM +0100, Mark Rutland wrote:
> > On Tue, Apr 18, 2017 at 06:21:07PM +0100, Lorenzo Pieralisi wrote:
> > > On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org wrote:
>  
> > > If yes, why can't it simply be written like this ?
> > > 
> > > for (; i >= 0; i--, gtdt_frame--) {
> > > 	frame = &timer_mem->frame[gtdt_frame->frame_number];
> > > 
> > > 	/* not sure this check is actually needed */
> > > 	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> > > 		continue;
> > > 
> > > 	if (frame->phys_irq > 0)
> > > 		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
> > > 	if (frame->virt_irq > 0)
> > > 		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
> > > }
> > 
> > A reverse loop of this form will work.
> > 
> > That requires some restructuring, and care to avoid going out of bounds
> > instantaneously with the gtdt_frame--, so as to not invoke nasal demons.
> > 
> > I've attacked this locally, and will send this out after testing. I'll
> > drop the new ACPI API patch.
> 
> FWIW, I've set this up so the cleanup path is:
> 
> do {
>         if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER ||
>             gtdt_frame->frame_number >= ARCH_TIMER_MEM_MAX_FRAMES)
>                 continue;
> 
>         frame = &timer_mem->frame[gtdt_frame->frame_number];
> 
>         if (frame->phys_irq > 0)
>                 acpi_unregister_gsi(gtdt_frame->timer_interrupt);
>         frame->phys_irq = 0;
> 
>         if (frame->virt_irq > 0)
>                 acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
>         frame->virt_irq = 0;
> } while (i-- >= 0 && gtdt_frame--);
> 
> ... the zeroing is to account for duplicate frames, which I now check for in
> the probe path (as we do for DT).
> 
> Can I take it per your comment on the prior version that with this change I can
> take your ack?

Yes, thanks for fixing it up, please add my:

Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi-5wv7dgnIgG8@public.gmane.org>

> I also assume that you're happy for all of the drivers/acpi/arm64/ patches in the
> series to go via the clocksource tree?

Yes that's how I expect them to go upstream, that's the simplest way.

Thanks !
Lorenzo
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 41+ messages in thread

* Re: [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
@ 2017-04-19 15:56           ` Lorenzo Pieralisi
  0 siblings, 0 replies; 41+ messages in thread
From: Lorenzo Pieralisi @ 2017-04-19 15:56 UTC (permalink / raw)
  To: Mark Rutland
  Cc: linaro-acpi, catalin.marinas, will.deacon, rruigrok, wim, fu.wei,
	wei, al.stone, tn, timur, daniel.lezcano, linux-acpi, linux,
	lenb, harba, julien.grall, linux-watchdog, arnd, marc.zyngier,
	jcm, cov, tglx, linux-arm-kernel, graeme.gregory, rjw,
	linux-kernel, leo.duran, hanjun.guo, Suravee.Suthikulpanit,
	sudeep.holla, christoffer.dall

On Wed, Apr 19, 2017 at 04:45:54PM +0100, Mark Rutland wrote:
> On Wed, Apr 19, 2017 at 04:07:25PM +0100, Mark Rutland wrote:
> > On Tue, Apr 18, 2017 at 06:21:07PM +0100, Lorenzo Pieralisi wrote:
> > > On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei@linaro.org wrote:
>  
> > > If yes, why can't it simply be written like this ?
> > > 
> > > for (; i >= 0; i--, gtdt_frame--) {
> > > 	frame = &timer_mem->frame[gtdt_frame->frame_number];
> > > 
> > > 	/* not sure this check is actually needed */
> > > 	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> > > 		continue;
> > > 
> > > 	if (frame->phys_irq > 0)
> > > 		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
> > > 	if (frame->virt_irq > 0)
> > > 		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
> > > }
> > 
> > A reverse loop of this form will work.
> > 
> > That requires some restructuring, and care to avoid going out of bounds
> > instantaneously with the gtdt_frame--, so as to not invoke nasal demons.
> > 
> > I've attacked this locally, and will send this out after testing. I'll
> > drop the new ACPI API patch.
> 
> FWIW, I've set this up so the cleanup path is:
> 
> do {
>         if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER ||
>             gtdt_frame->frame_number >= ARCH_TIMER_MEM_MAX_FRAMES)
>                 continue;
> 
>         frame = &timer_mem->frame[gtdt_frame->frame_number];
> 
>         if (frame->phys_irq > 0)
>                 acpi_unregister_gsi(gtdt_frame->timer_interrupt);
>         frame->phys_irq = 0;
> 
>         if (frame->virt_irq > 0)
>                 acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
>         frame->virt_irq = 0;
> } while (i-- >= 0 && gtdt_frame--);
> 
> ... the zeroing is to account for duplicate frames, which I now check for in
> the probe path (as we do for DT).
> 
> Can I take it per your comment on the prior version that with this change I can
> take your ack?

Yes, thanks for fixing it up, please add my:

Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

> I also assume that you're happy for all of the drivers/acpi/arm64/ patches in the
> series to go via the clocksource tree?

Yes that's how I expect them to go upstream, that's the simplest way.

Thanks !
Lorenzo

^ permalink raw reply	[flat|nested] 41+ messages in thread

* [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver
@ 2017-04-19 15:56           ` Lorenzo Pieralisi
  0 siblings, 0 replies; 41+ messages in thread
From: Lorenzo Pieralisi @ 2017-04-19 15:56 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, Apr 19, 2017 at 04:45:54PM +0100, Mark Rutland wrote:
> On Wed, Apr 19, 2017 at 04:07:25PM +0100, Mark Rutland wrote:
> > On Tue, Apr 18, 2017 at 06:21:07PM +0100, Lorenzo Pieralisi wrote:
> > > On Sat, Apr 15, 2017 at 02:40:12AM +0800, fu.wei at linaro.org wrote:
>  
> > > If yes, why can't it simply be written like this ?
> > > 
> > > for (; i >= 0; i--, gtdt_frame--) {
> > > 	frame = &timer_mem->frame[gtdt_frame->frame_number];
> > > 
> > > 	/* not sure this check is actually needed */
> > > 	if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER)
> > > 		continue;
> > > 
> > > 	if (frame->phys_irq > 0)
> > > 		acpi_unregister_gsi(gtdt_frame->timer_interrupt);
> > > 	if (frame->virt_irq > 0)
> > > 		acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
> > > }
> > 
> > A reverse loop of this form will work.
> > 
> > That requires some restructuring, and care to avoid going out of bounds
> > instantaneously with the gtdt_frame--, so as to not invoke nasal demons.
> > 
> > I've attacked this locally, and will send this out after testing. I'll
> > drop the new ACPI API patch.
> 
> FWIW, I've set this up so the cleanup path is:
> 
> do {
>         if (gtdt_frame->common_flags & ACPI_GTDT_GT_IS_SECURE_TIMER ||
>             gtdt_frame->frame_number >= ARCH_TIMER_MEM_MAX_FRAMES)
>                 continue;
> 
>         frame = &timer_mem->frame[gtdt_frame->frame_number];
> 
>         if (frame->phys_irq > 0)
>                 acpi_unregister_gsi(gtdt_frame->timer_interrupt);
>         frame->phys_irq = 0;
> 
>         if (frame->virt_irq > 0)
>                 acpi_unregister_gsi(gtdt_frame->virtual_timer_interrupt);
>         frame->virt_irq = 0;
> } while (i-- >= 0 && gtdt_frame--);
> 
> ... the zeroing is to account for duplicate frames, which I now check for in
> the probe path (as we do for DT).
> 
> Can I take it per your comment on the prior version that with this change I can
> take your ack?

Yes, thanks for fixing it up, please add my:

Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

> I also assume that you're happy for all of the drivers/acpi/arm64/ patches in the
> series to go via the clocksource tree?

Yes that's how I expect them to go upstream, that's the simplest way.

Thanks !
Lorenzo

^ permalink raw reply	[flat|nested] 41+ messages in thread

end of thread, other threads:[~2017-04-19 15:56 UTC | newest]

Thread overview: 41+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-04-14 18:40 [PATCH v24 00/11] acpi, clocksource: add GTDT driver and GTDT support in arm_arch_timer fu.wei
2017-04-14 18:40 ` fu.wei at linaro.org
2017-04-14 18:40 ` [PATCH v24 01/11] clocksource: arm_arch_timer: split dt-only rate handling fu.wei
2017-04-14 18:40   ` fu.wei at linaro.org
2017-04-14 18:40 ` [PATCH v24 02/11] clocksource: arm_arch_timer: refactor arch_timer_needs_probing fu.wei
2017-04-14 18:40   ` fu.wei at linaro.org
2017-04-14 18:40 ` [PATCH v24 03/11] clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call fu.wei
2017-04-14 18:40   ` fu.wei at linaro.org
2017-04-14 18:40 ` [PATCH v24 04/11] clocksource: arm_arch_timer: add structs to describe MMIO timer fu.wei
2017-04-14 18:40   ` fu.wei at linaro.org
     [not found] ` <20170414184014.8524-1-fu.wei-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2017-04-14 18:40   ` [PATCH v24 05/11] clocksource: arm_arch_timer: split MMIO timer probing fu.wei-QSEj5FYQhm4dnm+yROfE0A
2017-04-14 18:40     ` fu.wei at linaro.org
2017-04-14 18:40     ` fu.wei
2017-04-14 18:40   ` [PATCH v24 06/11] acpi/arm64: Add GTDT table parse driver fu.wei-QSEj5FYQhm4dnm+yROfE0A
2017-04-14 18:40     ` fu.wei at linaro.org
2017-04-14 18:40     ` fu.wei
2017-04-14 18:40 ` [PATCH v24 07/11] clocksource: arm_arch_timer: simplify ACPI support code fu.wei
2017-04-14 18:40   ` fu.wei at linaro.org
2017-04-14 18:40 ` [PATCH v24 08/11] acpi: Introduce acpi_unregister_irq function fu.wei
2017-04-14 18:40   ` fu.wei at linaro.org
2017-04-18 15:58   ` Mark Rutland
2017-04-18 15:58     ` Mark Rutland
2017-04-19 15:09     ` Mark Rutland
2017-04-19 15:09       ` Mark Rutland
2017-04-14 18:40 ` [PATCH v24 09/11] acpi/arm64: Add memory-mapped timer support in GTDT driver fu.wei
2017-04-14 18:40   ` fu.wei at linaro.org
2017-04-18 17:21   ` Lorenzo Pieralisi
2017-04-18 17:21     ` Lorenzo Pieralisi
2017-04-19 15:07     ` Mark Rutland
2017-04-19 15:07       ` Mark Rutland
2017-04-19 15:45       ` Mark Rutland
2017-04-19 15:45         ` Mark Rutland
2017-04-19 15:45         ` Mark Rutland
2017-04-19 15:56         ` Lorenzo Pieralisi
2017-04-19 15:56           ` Lorenzo Pieralisi
2017-04-19 15:56           ` Lorenzo Pieralisi
2017-04-14 18:40 ` [PATCH v24 10/11] clocksource: arm_arch_timer: add GTDT support for memory-mapped timer fu.wei
2017-04-14 18:40   ` fu.wei at linaro.org
2017-04-14 18:40 ` [PATCH v24 11/11] acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver fu.wei
2017-04-14 18:40   ` fu.wei at linaro.org
2017-04-14 18:40   ` fu.wei

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.