From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751516AbdFETIp (ORCPT ); Mon, 5 Jun 2017 15:08:45 -0400 Received: from mail.kernel.org ([198.145.29.99]:44706 "EHLO mail.kernel.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751349AbdFETHP (ORCPT ); Mon, 5 Jun 2017 15:07:15 -0400 DMARC-Filter: OpenDMARC Filter v1.3.2 mail.kernel.org 3CC6923A50 Authentication-Results: mail.kernel.org; dmarc=none (p=none dis=none) header.from=kernel.org Authentication-Results: mail.kernel.org; spf=none smtp.mailfrom=atull@kernel.org From: Alan Tull To: Greg Kroah-Hartman Cc: linux-kernel@vger.kernel.org, linux-fpga@vger.kernel.org, Moritz Fischer , delicious.quinoa@gmail.com, Joshua Clayton , Alan Tull Subject: [PATCH 05/10] doc: dt: document altera-passive-serial binding Date: Mon, 5 Jun 2017 14:07:36 -0500 Message-Id: <20170605190741.10508-6-atull@kernel.org> X-Mailer: git-send-email 2.11.0 In-Reply-To: <20170605190741.10508-1-atull@kernel.org> References: <20170605190741.10508-1-atull@kernel.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org From: Joshua Clayton Describe an altera-passive-serial devicetree entry, required features Signed-off-by: Joshua Clayton Acked-by: Rob Herring Signed-off-by: Alan Tull --- .../bindings/fpga/altera-passive-serial.txt | 29 ++++++++++++++++++++++ 1 file changed, 29 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/altera-passive-serial.txt diff --git a/Documentation/devicetree/bindings/fpga/altera-passive-serial.txt b/Documentation/devicetree/bindings/fpga/altera-passive-serial.txt new file mode 100644 index 000000000000..48478bc07e29 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-passive-serial.txt @@ -0,0 +1,29 @@ +Altera Passive Serial SPI FPGA Manager + +Altera FPGAs support a method of loading the bitstream over what is +referred to as "passive serial". +The passive serial link is not technically SPI, and might require extra +circuits in order to play nicely with other SPI slaves on the same bus. + +See https://www.altera.com/literature/hb/cyc/cyc_c51013.pdf + +Required properties: +- compatible: Must be one of the following: + "altr,fpga-passive-serial", + "altr,fpga-arria10-passive-serial" +- reg: SPI chip select of the FPGA +- nconfig-gpios: config pin (referred to as nCONFIG in the manual) +- nstat-gpios: status pin (referred to as nSTATUS in the manual) + +Optional properties: +- confd-gpios: confd pin (referred to as CONF_DONE in the manual) + +Example: + fpga: fpga@0 { + compatible = "altr,fpga-passive-serial"; + spi-max-frequency = <20000000>; + reg = <0>; + nconfig-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>; + nstat-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; + confd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; + }; -- 2.11.0