From mboxrd@z Thu Jan 1 00:00:00 1970 From: Maxime Ripard Subject: [PATCH 1/2] dt-bindings: media: Add Cadence MIPI-CSI2 TX Device Tree bindings Date: Fri, 22 Sep 2017 13:47:02 +0200 Message-ID: <20170922114703.30511-2-maxime.ripard@free-electrons.com> References: <20170922114703.30511-1-maxime.ripard@free-electrons.com> Return-path: In-Reply-To: <20170922114703.30511-1-maxime.ripard@free-electrons.com> Sender: linux-media-owner@vger.kernel.org To: Mauro Carvalho Chehab , Mark Rutland , Rob Herring Cc: Laurent Pinchart , linux-media@vger.kernel.org, devicetree@vger.kernel.org, Cyprian Wronka , Richard Sproul , Alan Douglas , Steve Creaney , Thomas Petazzoni , Boris Brezillon , =?UTF-8?q?Niklas=20S=C3=B6derlund?= , Hans Verkuil , Sakari Ailus , Benoit Parrot , nm@ti.com, Maxime Ripard List-Id: devicetree@vger.kernel.org The Cadence MIPI-CSI2 RX controller is a CSI2 bridge that supports up to 4 video streams and can output on up to 4 CSI-2 lanes, depending on the hardware implementation. It can operate with an external D-PHY, an internal one or no D-PHY at all in some configurations. Signed-off-by: Maxime Ripard --- .../devicetree/bindings/media/cdns,csi2tx.txt | 97 ++++++++++++++++++++++ 1 file changed, 97 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/cdns,csi2tx.txt diff --git a/Documentation/devicetree/bindings/media/cdns,csi2tx.txt b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt new file mode 100644 index 000000000000..5fb70bba910e --- /dev/null +++ b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt @@ -0,0 +1,97 @@ +Cadence MIPI-CSI2 TX controller +=============================== + +The Cadence MIPI-CSI2 TX controller is a CSI-2 bridge supporting up to +4 CSI lanes in output, and up to 4 different pixel streams in input. + +Required properties: + - compatible: must be set to "cdns,csi2tx" + - reg: base address and size of the memory mapped region + - clocks: phandles to the clocks driving the controller + - clock-names: must contain: + * esc_clk: escape mode clock + * p_clk: register bank clock + * pixel_if[0-3]_clk: pixel stream output clock, one for each stream + implemented in hardware, between 0 and 3 + +Optional properties + - phys: phandle to the D-PHY. If it is set, phy-names need to be set + - phy-names: must contain dphy + +Required subnodes: + - ports: A ports node with one port child node per device input and output + port, in accordance with the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + port nodes numbered as follows. + + Port Description + ----------------------------- + 0 CSI-2 output + 1 Stream 0 input + 2 Stream 1 input + 3 Stream 2 input + 4 Stream 3 input + + The stream input port nodes are optional if they are not + connected to anything at the hardware level or implemented + in the design. + +Example: + +csi2tx: csi-bridge@0d0e1000 { + compatible = "cdns,csi2tx"; + reg = <0x0d0e1000 0x1000>; + clocks = <&byteclock>, <&byteclock>, + <&coreclock>, <&coreclock>, + <&coreclock>, <&coreclock>; + clock-names = "p_clk", "esc_clk", + "pixel_if0_clk", "pixel_if1_clk", + "pixel_if2_clk", "pixel_if3_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi2tx_out: endpoint { + remote-endpoint = <&remote_in>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + + csi2tx_in_stream0: endpoint { + remote-endpoint = <&stream0_out>; + }; + }; + + port@2 { + reg = <2>; + + csi2tx_in_stream1: endpoint { + remote-endpoint = <&stream1_out>; + }; + }; + + port@3 { + reg = <3>; + + csi2tx_in_stream2: endpoint { + remote-endpoint = <&stream2_out>; + }; + }; + + port@4 { + reg = <4>; + + csi2tx_in_stream3: endpoint { + remote-endpoint = <&stream3_out>; + }; + }; + }; +}; -- 2.13.5