[U-Boot] [PATCH v4] imx:display5: Add support for LWN's DISPLAY5 board (for v2017.11-rc2+)

[Lukasz Majewski <lukma@denx.de>]

Hi Stefano,

> Hi Lukasz,
> 
> On 31/10/2017 17:58, Lukasz Majewski wrote:
> > This commit provides support for LWN's IMX6Q based DISPLAY5 board.
> >   
> 
> I would merge it, but why the commit message is still "(for
> v2017.11-rc2+)" ? This goes into git history if I merge it.
> 
> Can I drop it by merging ?

Yes. Please.

(I should not put it there in a first place).

Thanks :-)

> 
> Best regards,
> Stefano
> 
> > Signed-off-by: Lukasz Majewski <lukma@denx.de>
> > 
> > ---
> > 
> > Changes in v4:
> >     - Refactor obscure sw/hw rev code for display5 board
> >     - replace get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
> > with imx_ddr_size()
> >     - remove PHYS_SDRAM_SIZE from display5.h
> >     - Replace non generic setup of RGMII pins voltage levels with a
> > generic function
> >     - Move displ5_set_iomux_uart() - non console UART init to
> > board_init()
> >     - Disable board_early_init_f() calls (prod/factory)
> >     - Move mtdparts to Kconfig for production and flash u-boot
> > 
> > Changes in v3:
> >     - Remove ip custom data
> >     - Cleanup SPL code
> > 
> > Changes in v2:
> >     - Update to newest mainline u-boot
> > 
> >  arch/arm/dts/imx6q-display5.dts     |  18 ++
> >  arch/arm/mach-imx/mx6/Kconfig       |   7 +
> >  board/liebherr/display5/Kconfig     |  18 ++
> >  board/liebherr/display5/MAINTAINERS |   7 +
> >  board/liebherr/display5/Makefile    |  11 +
> >  board/liebherr/display5/common.c    | 111 ++++++++++
> >  board/liebherr/display5/common.h    |  42 ++++
> >  board/liebherr/display5/display5.c  | 384
> > +++++++++++++++++++++++++++++++++
> > board/liebherr/display5/spl.c       | 247 ++++++++++++++++++++++
> > configs/display5_defconfig          |  62 ++++++
> > configs/display5_factory_defconfig  |  76 +++++++
> > include/configs/display5.h          | 408
> > ++++++++++++++++++++++++++++++++++++ 12 files changed, 1391
> > insertions(+) create mode 100644 arch/arm/dts/imx6q-display5.dts
> > create mode 100644 board/liebherr/display5/Kconfig create mode
> > 100644 board/liebherr/display5/MAINTAINERS create mode 100644
> > board/liebherr/display5/Makefile create mode 100644
> > board/liebherr/display5/common.c create mode 100644
> > board/liebherr/display5/common.h create mode 100644
> > board/liebherr/display5/display5.c create mode 100644
> > board/liebherr/display5/spl.c create mode 100644
> > configs/display5_defconfig create mode 100644
> > configs/display5_factory_defconfig create mode 100644
> > include/configs/display5.h
> > 
> > diff --git a/arch/arm/dts/imx6q-display5.dts
> > b/arch/arm/dts/imx6q-display5.dts new file mode 100644
> > index 0000000000..50347ff26b
> > --- /dev/null
> > +++ b/arch/arm/dts/imx6q-display5.dts
> > @@ -0,0 +1,18 @@
> > +/*
> > + * Copyright 2017
> > + * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
> > + *
> > + * This program is free software; you can redistribute it and/or
> > modify
> > + * it under the terms of the GNU General Public License version 2
> > as
> > + * published by the Free Software Foundation.
> > + *
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx6q.dtsi"
> > +
> > +/ {
> > +	model = "Liebherr (LWN) display5 i.MX6 Quad Board";
> > +	compatible = "lwn,display5", "fsl,imx6q";
> > +};
> > diff --git a/arch/arm/mach-imx/mx6/Kconfig
> > b/arch/arm/mach-imx/mx6/Kconfig index b82db3af22..fd73c67fde 100644
> > --- a/arch/arm/mach-imx/mx6/Kconfig
> > +++ b/arch/arm/mach-imx/mx6/Kconfig
> > @@ -138,6 +138,12 @@ config TARGET_DHCOMIMX6
> >  	select DM_THERMAL
> >  	imply CMD_SPL
> >  
> > +config TARGET_DISPLAY5
> > +	bool "LWN DISPLAY5 board"
> > +	select SUPPORT_SPL
> > +	select DM
> > +	select DM_SERIAL
> > +
> >  config TARGET_EMBESTMX6BOARDS
> >  	bool "embestmx6boards"
> >  	select BOARD_LATE_INIT
> > @@ -459,6 +465,7 @@ source "board/phytec/pfla02/Kconfig"
> >  source "board/gateworks/gw_ventana/Kconfig"
> >  source "board/kosagi/novena/Kconfig"
> >  source "board/samtec/vining_2000/Kconfig"
> > +source "board/liebherr/display5/Kconfig"
> >  source "board/liebherr/mccmon6/Kconfig"
> >  source "board/logicpd/imx6/Kconfig"
> >  source "board/seco/Kconfig"
> > diff --git a/board/liebherr/display5/Kconfig
> > b/board/liebherr/display5/Kconfig new file mode 100644
> > index 0000000000..b096c8917a
> > --- /dev/null
> > +++ b/board/liebherr/display5/Kconfig
> > @@ -0,0 +1,18 @@
> > +if TARGET_DISPLAY5
> > +
> > +config SYS_CPU
> > +	default "armv7"
> > +
> > +config SYS_BOARD
> > +	default "display5"
> > +
> > +config SYS_VENDOR
> > +	default "liebherr"
> > +
> > +config SYS_SOC
> > +	default "mx6"
> > +
> > +config SYS_CONFIG_NAME
> > +	default "display5"
> > +
> > +endif
> > diff --git a/board/liebherr/display5/MAINTAINERS
> > b/board/liebherr/display5/MAINTAINERS new file mode 100644
> > index 0000000000..52178318b5
> > --- /dev/null
> > +++ b/board/liebherr/display5/MAINTAINERS
> > @@ -0,0 +1,7 @@
> > +DISPLAY5 BOARD
> > +M:	Lukasz Majewski <lukma@denx.de>
> > +S:	Maintained
> > +F:	board/liebherr/display5/
> > +F:	include/configs/display5.h
> > +F:	configs/display5_defconfig
> > +F:	configs/display5_factory_defconfig
> > diff --git a/board/liebherr/display5/Makefile
> > b/board/liebherr/display5/Makefile new file mode 100644
> > index 0000000000..f934672428
> > --- /dev/null
> > +++ b/board/liebherr/display5/Makefile
> > @@ -0,0 +1,11 @@
> > +#
> > +# Copyright (C) 2017, DENX Software Engineering
> > +# Lukasz Majewski <lukma@denx.de>
> > +#
> > +# SPDX-License-Identifier:    GPL-2.0+
> > +#
> > +ifdef CONFIG_SPL_BUILD
> > +obj-y = common.o spl.o
> > +else
> > +obj-y := common.o display5.o
> > +endif
> > diff --git a/board/liebherr/display5/common.c
> > b/board/liebherr/display5/common.c new file mode 100644
> > index 0000000000..03f585b3aa
> > --- /dev/null
> > +++ b/board/liebherr/display5/common.c
> > @@ -0,0 +1,111 @@
> > +/*
> > + * Copyright (C) 2017 DENX Software Engineering
> > + * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
> > + *
> > + * SPDX-License-Identifier:	GPL-2.0+
> > + */
> > +
> > +#include <asm/mach-imx/iomux-v3.h>
> > +#include <asm/arch/mx6-pins.h>
> > +#include "common.h"
> > +
> > +iomux_v3_cfg_t const uart_pads[] = {
> > +	/* UART4 */
> > +	MX6_PAD_CSI0_DAT12__UART4_TX_DATA |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > +	MX6_PAD_CSI0_DAT13__UART4_RX_DATA |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > +	MX6_PAD_CSI0_DAT16__UART4_RTS_B |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > +	MX6_PAD_CSI0_DAT17__UART4_CTS_B |
> > MUX_PAD_CTRL(UART_PAD_CTRL), +};
> > +
> > +iomux_v3_cfg_t const uart_console_pads[] = {
> > +	/* UART5 */
> > +	MX6_PAD_CSI0_DAT14__UART5_TX_DATA |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > +	MX6_PAD_CSI0_DAT15__UART5_RX_DATA |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > +	MX6_PAD_CSI0_DAT18__UART5_RTS_B |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > +	MX6_PAD_CSI0_DAT19__UART5_CTS_B |
> > MUX_PAD_CTRL(UART_PAD_CTRL), +};
> > +
> > +void displ5_set_iomux_uart_spl(void)
> > +{
> > +	SETUP_IOMUX_PADS(uart_console_pads);
> > +}
> > +
> > +void displ5_set_iomux_uart(void)
> > +{
> > +	SETUP_IOMUX_PADS(uart_pads);
> > +}
> > +
> > +#ifdef CONFIG_MXC_SPI
> > +iomux_v3_cfg_t const ecspi_pads[] = {
> > +	/* SPI3 */
> > +	MX6_PAD_DISP0_DAT2__ECSPI3_MISO	|
> > MUX_PAD_CTRL(SPI_PAD_CTRL),
> > +	MX6_PAD_DISP0_DAT1__ECSPI3_MOSI	|
> > MUX_PAD_CTRL(SPI_PAD_CTRL),
> > +	MX6_PAD_DISP0_DAT0__ECSPI3_SCLK	|
> > MUX_PAD_CTRL(SPI_PAD_CTRL),
> > +	MX6_PAD_DISP0_DAT3__ECSPI3_SS0	|
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_DISP0_DAT4__ECSPI3_SS1	|
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_DISP0_DAT5__ECSPI3_SS2	|
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_DISP0_DAT6__ECSPI3_SS3	|
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_DISP0_DAT7__ECSPI3_RDY	|
> > MUX_PAD_CTRL(NO_PAD_CTRL), +};
> > +
> > +iomux_v3_cfg_t const ecspi2_pads[] = {
> > +	/* SPI2, NOR Flash nWP, CS0 */
> > +	MX6_PAD_CSI0_DAT10__ECSPI2_MISO	|
> > MUX_PAD_CTRL(SPI_PAD_CTRL),
> > +	MX6_PAD_CSI0_DAT9__ECSPI2_MOSI	|
> > MUX_PAD_CTRL(SPI_PAD_CTRL),
> > +	MX6_PAD_CSI0_DAT8__ECSPI2_SCLK	|
> > MUX_PAD_CTRL(SPI_PAD_CTRL),
> > +	MX6_PAD_CSI0_DAT11__GPIO5_IO29	|
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_SD3_DAT5__GPIO7_IO00	|
> > MUX_PAD_CTRL(NO_PAD_CTRL), +};
> > +
> > +int board_spi_cs_gpio(unsigned int bus, unsigned int cs)
> > +{
> > +	if (bus != 1 || cs != (IMX_GPIO_NR(5, 29) << 8))
> > +		return -EINVAL;
> > +
> > +	return IMX_GPIO_NR(5, 29);
> > +}
> > +
> > +void displ5_set_iomux_ecspi_spl(void)
> > +{
> > +	SETUP_IOMUX_PADS(ecspi2_pads);
> > +}
> > +
> > +void displ5_set_iomux_ecspi(void)
> > +{
> > +	SETUP_IOMUX_PADS(ecspi_pads);
> > +}
> > +
> > +#else
> > +void displ5_set_iomux_ecspi_spl(void) {}
> > +void displ5_set_iomux_ecspi(void) {}
> > +#endif
> > +
> > +#ifdef CONFIG_FSL_ESDHC
> > +iomux_v3_cfg_t const usdhc4_pads[] = {
> > +	MX6_PAD_SD4_CLK__SD4_CLK	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_SD4_CMD__SD4_CMD	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_SD4_DAT0__SD4_DATA0	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_SD4_DAT1__SD4_DATA1	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_SD4_DAT2__SD4_DATA2	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_SD4_DAT3__SD4_DATA3	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_SD4_DAT4__SD4_DATA4	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_SD4_DAT5__SD4_DATA5	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_SD4_DAT6__SD4_DATA6	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_SD4_DAT7__SD4_DATA7	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > +	MX6_PAD_NANDF_ALE__SD4_RESET	|
> > MUX_PAD_CTRL(USDHC_PAD_CTRL), +};
> > +
> > +void displ5_set_iomux_usdhc_spl(void)
> > +{
> > +	SETUP_IOMUX_PADS(usdhc4_pads);
> > +}
> > +
> > +void displ5_set_iomux_usdhc(void)
> > +{
> > +	SETUP_IOMUX_PADS(usdhc4_pads);
> > +}
> > +
> > +#else
> > +void displ5_set_iomux_usdhc_spl(void) {}
> > +void displ5_set_iomux_usdhc(void) {}
> > +#endif
> > diff --git a/board/liebherr/display5/common.h
> > b/board/liebherr/display5/common.h new file mode 100644
> > index 0000000000..6019e90c61
> > --- /dev/null
> > +++ b/board/liebherr/display5/common.h
> > @@ -0,0 +1,42 @@
> > +/*
> > + * Copyright (C) 2017 DENX Software Engineering
> > + * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
> > + *
> > + * SPDX-License-Identifier:	GPL-2.0+
> > + */
> > +
> > +#ifndef __DISPL5_COMMON_H_
> > +#define __DISPL5_COMMON_H_
> > +
> > +#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |	       \
> > +	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |	       \
> > +	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
> > +
> > +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |	       \
> > +	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |	       \
> > +	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
> > +
> > +#define ENET_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |
> > \
> > +	PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_MED
> > |		\
> > +	PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)
> > +
> > +#define SPI_PAD_CTRL (PAD_CTL_HYS |
> > \
> > +	PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED |
> > \
> > +	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
> > +
> > +#define I2C_PAD_CTRL	(PAD_CTL_PKE | PAD_CTL_PUE
> > |		\
> > +	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
> > +	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |			\
> > +	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
> > +
> > +#define ENET_PAD_CTRL_CLK  ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) |
> > \
> > +	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
> > +
> > +void displ5_set_iomux_uart_spl(void);
> > +void displ5_set_iomux_uart(void);
> > +void displ5_set_iomux_ecspi_spl(void);
> > +void displ5_set_iomux_ecspi(void);
> > +void displ5_set_iomux_usdhc_spl(void);
> > +void displ5_set_iomux_usdhc(void);
> > +
> > +#endif /* __DISPL5_COMMON_H_ */
> > diff --git a/board/liebherr/display5/display5.c
> > b/board/liebherr/display5/display5.c new file mode 100644
> > index 0000000000..5414ef77d3
> > --- /dev/null
> > +++ b/board/liebherr/display5/display5.c
> > @@ -0,0 +1,384 @@
> > +/*
> > + * Copyright (C) 2017 DENX Software Engineering
> > + * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
> > + *
> > + * SPDX-License-Identifier:	GPL-2.0+
> > + */
> > +
> > +#include <common.h>
> > +#include <dm.h>
> > +#include <asm/io.h>
> > +#include <asm/arch/clock.h>
> > +#include <asm/arch/imx-regs.h>
> > +#include <asm/arch/iomux.h>
> > +#include <asm/arch/mx6-pins.h>
> > +#include <asm/arch/mx6-ddr.h>
> > +#include <asm/arch/sys_proto.h>
> > +#include <errno.h>
> > +#include <asm/gpio.h>
> > +#include <malloc.h>
> > +#include <asm/mach-imx/iomux-v3.h>
> > +#include <asm/mach-imx/mxc_i2c.h>
> > +#include <asm/mach-imx/boot_mode.h>
> > +#include <asm/mach-imx/spi.h>
> > +#include <mmc.h>
> > +#include <fsl_esdhc.h>
> > +#include <miiphy.h>
> > +#include <netdev.h>
> > +#include <i2c.h>
> > +
> > +#include <dm.h>
> > +#include <dm/platform_data/serial_mxc.h>
> > +#include <dm/platdata.h>
> > +
> > +#ifndef CONFIG_MXC_SPI
> > +#error "CONFIG_SPI must be set for this board"
> > +#error "Please check your config file"
> > +#endif
> > +
> > +#include "common.h"
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +static bool hw_ids_valid;
> > +static bool sw_ids_valid;
> > +static u32 cpu_id;
> > +static u32 unit_id;
> > +
> > +#define SW0	IMX_GPIO_NR(2, 4)
> > +#define SW1	IMX_GPIO_NR(2, 5)
> > +#define SW2	IMX_GPIO_NR(2, 6)
> > +#define SW3	IMX_GPIO_NR(2, 7)
> > +#define HW0	IMX_GPIO_NR(6, 7)
> > +#define HW1	IMX_GPIO_NR(6, 9)
> > +#define HW2	IMX_GPIO_NR(6, 10)
> > +#define HW3	IMX_GPIO_NR(6, 11)
> > +#define HW4	IMX_GPIO_NR(4, 7)
> > +#define HW5	IMX_GPIO_NR(4, 11)
> > +#define HW6	IMX_GPIO_NR(4, 13)
> > +#define HW7	IMX_GPIO_NR(4, 15)
> > +
> > +int gpio_table_sw_ids[] = {
> > +	SW0, SW1, SW2, SW3
> > +};
> > +
> > +const char *gpio_table_sw_ids_names[] = {
> > +	"sw0", "sw1", "sw2", "sw3"
> > +};
> > +
> > +int gpio_table_hw_ids[] = {
> > +	HW0, HW1, HW2, HW3, HW4, HW5, HW6, HW7
> > +};
> > +
> > +const char *gpio_table_hw_ids_names[] = {
> > +	"hw0", "hw1", "hw2", "hw3", "hw4", "hw5", "hw6", "hw7"
> > +};
> > +
> > +static int get_board_id(int *ids, const char **c, int size,
> > +			bool *valid, u32 *id)
> > +{
> > +	int i, ret, val;
> > +
> > +	*valid = false;
> > +
> > +	for (i = 0; i < size; i++) {
> > +		ret = gpio_request(ids[i], c[i]);
> > +		if (ret) {
> > +			printf("Can't request SWx gpios\n");
> > +			return ret;
> > +		}
> > +	}
> > +
> > +	for (i = 0; i < size; i++) {
> > +		ret = gpio_direction_input(ids[i]);
> > +		if (ret) {
> > +			printf("Can't set SWx gpios direction\n");
> > +			return ret;
> > +		}
> > +	}
> > +
> > +	for (i = 0; i < size; i++) {
> > +		val = gpio_get_value(ids[i]);
> > +		if (val < 0) {
> > +			printf("Can't get SW%d ID\n", i);
> > +			*id = 0;
> > +			return val;
> > +		}
> > +		*id |= val << i;
> > +	}
> > +	*valid = true;
> > +
> > +	return 0;
> > +}
> > +
> > +int dram_init(void)
> > +{
> > +	gd->ram_size = imx_ddr_size();
> > +
> > +	return 0;
> > +}
> > +
> > +#define PC	MUX_PAD_CTRL(I2C_PAD_CTRL)
> > +/* I2C1: TFA9879 */
> > +struct i2c_pads_info i2c_pad_info0 = {
> > +	.scl = {
> > +		.i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC,
> > +		.gpio_mode = MX6_PAD_EIM_D21__GPIO3_IO21 | PC,
> > +		.gp = IMX_GPIO_NR(3, 21)
> > +	},
> > +	.sda = {
> > +		.i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC,
> > +		.gpio_mode = MX6_PAD_EIM_D28__GPIO3_IO28 | PC,
> > +		.gp = IMX_GPIO_NR(3, 28)
> > +	}
> > +};
> > +
> > +/* I2C2: TIVO TM4C123 */
> > +struct i2c_pads_info i2c_pad_info1 = {
> > +	.scl = {
> > +		.i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
> > +		.gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC,
> > +		.gp = IMX_GPIO_NR(2, 30)
> > +	},
> > +	.sda = {
> > +		.i2c_mode = MX6_PAD_EIM_D16__I2C2_SDA | PC,
> > +		.gpio_mode = MX6_PAD_EIM_D16__GPIO3_IO16 | PC,
> > +		.gp = IMX_GPIO_NR(3, 16)
> > +	}
> > +};
> > +
> > +/* I2C3: PMIC PF0100, EEPROM AT24C256C */
> > +struct i2c_pads_info i2c_pad_info2 = {
> > +	.scl = {
> > +		.i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
> > +		.gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
> > +		.gp = IMX_GPIO_NR(3, 17)
> > +	},
> > +	.sda = {
> > +		.i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
> > +		.gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
> > +		.gp = IMX_GPIO_NR(3, 18)
> > +	}
> > +};
> > +
> > +iomux_v3_cfg_t const misc_pads[] = {
> > +	/* Prod ID GPIO pins */
> > +	MX6_PAD_NANDF_D4__GPIO2_IO04    |
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_NANDF_D5__GPIO2_IO05    |
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_NANDF_D6__GPIO2_IO06    |
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_NANDF_D7__GPIO2_IO07    |
> > MUX_PAD_CTRL(NO_PAD_CTRL), +
> > +	/* HW revision GPIO pins */
> > +	MX6_PAD_NANDF_CLE__GPIO6_IO07   |
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_NANDF_WP_B__GPIO6_IO09  |
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_NANDF_RB0__GPIO6_IO10   |
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_NANDF_CS0__GPIO6_IO11   |
> > MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_KEY_ROW3__GPIO4_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
> > +	MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
> > +
> > +	/* XTALOSC */
> > +	MX6_PAD_GPIO_3__XTALOSC_REF_CLK_24M |
> > MUX_PAD_CTRL(NO_PAD_CTRL), +};
> > +
> > +#ifdef CONFIG_FSL_ESDHC
> > +struct fsl_esdhc_cfg usdhc_cfg[1] = {
> > +	{ USDHC4_BASE_ADDR, 0, 8, },
> > +};
> > +
> > +int board_mmc_getcd(struct mmc *mmc)
> > +{
> > +	return 1;
> > +}
> > +
> > +int board_mmc_init(bd_t *bis)
> > +{
> > +	displ5_set_iomux_usdhc();
> > +
> > +	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
> > +
> > +	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
> > +}
> > +#endif /* CONFIG_FSL_ESDHC */
> > +
> > +static void displ5_setup_ecspi(void)
> > +{
> > +	int ret;
> > +
> > +	displ5_set_iomux_ecspi();
> > +
> > +	ret = gpio_request(IMX_GPIO_NR(5, 29), "spi2_cs0");
> > +	if (!ret)
> > +		gpio_direction_output(IMX_GPIO_NR(5, 29), 1);
> > +
> > +	ret = gpio_request(IMX_GPIO_NR(7, 0), "spi2_#wp");
> > +	if (!ret)
> > +		gpio_direction_output(IMX_GPIO_NR(7, 0), 1);
> > +}
> > +
> > +#ifdef CONFIG_FEC_MXC
> > +iomux_v3_cfg_t const enet_pads[] = {
> > +	MX6_PAD_ENET_TXD1__ENET_1588_EVENT0_IN	|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_ENET_RXD1__ENET_1588_EVENT3_OUT |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_ENET_MDIO__ENET_MDIO		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_ENET_MDC__ENET_MDC		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	|
> > MUX_PAD_CTRL(ENET_PAD_CTRL), +
> > +	/* for old evalboard with R159 present and R160 not
> > populated */
> > +	MX6_PAD_GPIO_16__ENET_REF_CLK		|
> > MUX_PAD_CTRL(NO_PAD_CTRL), +
> > +	MX6_PAD_RGMII_TXC__RGMII_TXC		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_TD0__RGMII_TD0		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_TD1__RGMII_TD1		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_TD2__RGMII_TD2		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_TD3__RGMII_TD3		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	|
> > MUX_PAD_CTRL(ENET_PAD_CTRL), +
> > +	MX6_PAD_RGMII_RXC__RGMII_RXC		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_RD0__RGMII_RD0		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_RD1__RGMII_RD1		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_RD2__RGMII_RD2		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_RD3__RGMII_RD3		|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	|
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +	/*INT#_GBE*/
> > +	MX6_PAD_ENET_TX_EN__GPIO1_IO28		|
> > MUX_PAD_CTRL(NO_PAD_CTRL), +};
> > +
> > +static void setup_iomux_enet(void)
> > +{
> > +	SETUP_IOMUX_PADS(enet_pads);
> > +	gpio_direction_input(IMX_GPIO_NR(1, 28)); /*INT#_GBE*/
> > +}
> > +
> > +int board_eth_init(bd_t *bd)
> > +{
> > +	struct phy_device *phydev;
> > +	struct mii_dev *bus;
> > +	int ret;
> > +
> > +	setup_iomux_enet();
> > +
> > +	iomuxc_set_rgmii_io_voltage(DDR_SEL_1P5V_IO);
> > +
> > +	ret = enable_fec_anatop_clock(0, ENET_125MHZ);
> > +	if (ret)
> > +		return ret;
> > +
> > +	bus = fec_get_miibus(IMX_FEC_BASE, -1);
> > +	if (!bus)
> > +		return -ENODEV;
> > +
> > +	/*
> > +	 * We use here the "rgmii-id" mode of operation and allow
> > M88E1512
> > +	 * PHY to use its internally callibrated RX/TX delays
> > +	 */
> > +	phydev = phy_find_by_mask(bus, 0xffffffff /* (0xf << 4) */,
> > +				  PHY_INTERFACE_MODE_RGMII_ID);
> > +	if (!phydev) {
> > +		ret = -ENODEV;
> > +		goto err_phy;
> > +	}
> > +
> > +	/* display5 due to PCB routing can only work with 100 Mbps
> > */
> > +	phydev->advertising &= ~(ADVERTISED_1000baseX_Half |
> > +				 ADVERTISED_1000baseX_Full |
> > +				 SUPPORTED_1000baseT_Half |
> > +				 SUPPORTED_1000baseT_Full);
> > +
> > +	ret  = fec_probe(bd, -1, IMX_FEC_BASE, bus, phydev);
> > +	if (ret)
> > +		goto err_sw;
> > +
> > +	return 0;
> > +
> > +err_sw:
> > +	free(phydev);
> > +err_phy:
> > +	mdio_unregister(bus);
> > +	free(bus);
> > +	return ret;
> > +}
> > +#endif /* CONFIG_FEC_MXC */
> > +
> > +/*
> > + * Do not overwrite the console
> > + * Always use serial for U-Boot console
> > + */
> > +int overwrite_console(void)
> > +{
> > +	return 1;
> > +}
> > +
> > +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
> > +int ft_board_setup(void *blob, bd_t *bd)
> > +{
> > +	fdt_fixup_ethernet(blob);
> > +	return 0;
> > +}
> > +#endif
> > +
> > +int board_init(void)
> > +{
> > +	debug("board init\n");
> > +	/* address of boot parameters */
> > +	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
> > +
> > +	/* Setup iomux for non console UARTS */
> > +	displ5_set_iomux_uart();
> > +
> > +	displ5_setup_ecspi();
> > +
> > +	SETUP_IOMUX_PADS(misc_pads);
> > +
> > +	get_board_id(gpio_table_sw_ids,
> > &gpio_table_sw_ids_names[0],
> > +		     ARRAY_SIZE(gpio_table_sw_ids), &sw_ids_valid,
> > &unit_id);
> > +	debug("SWx unit_id 0x%x\n", unit_id);
> > +
> > +	get_board_id(gpio_table_hw_ids,
> > &gpio_table_hw_ids_names[0],
> > +		     ARRAY_SIZE(gpio_table_hw_ids), &hw_ids_valid,
> > &cpu_id);
> > +	debug("HWx cpu_id 0x%x\n", cpu_id);
> > +
> > +	if (hw_ids_valid && sw_ids_valid)
> > +		printf("ID:    unit type 0x%x rev 0x%x\n",
> > unit_id, cpu_id); +
> > +	udelay(25);
> > +
> > +	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
> > +	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
> > +	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
> > +
> > +	return 0;
> > +}
> > +
> > +#ifdef CONFIG_CMD_BMODE
> > +static const struct boot_mode board_boot_modes[] = {
> > +	/* eMMC, USDHC-4, 8-bit bus width */
> > +	/* SPI-NOR, ECSPI-2 SS0, 3-bytes addressing */
> > +	{"emmc",    MAKE_CFGVAL(0x60, 0x58, 0x00, 0x00)},
> > +	{"spinor",  MAKE_CFGVAL(0x30, 0x00, 0x00, 0x09)},
> > +	{NULL,	0},
> > +};
> > +
> > +static void setup_boot_modes(void)
> > +{
> > +	add_board_boot_modes(board_boot_modes);
> > +}
> > +#else
> > +static inline void setup_boot_modes(void) {}
> > +#endif
> > +
> > +int misc_init_r(void)
> > +{
> > +	setup_boot_modes();
> > +	return 0;
> > +}
> > +
> > +static struct mxc_serial_platdata mxc_serial_plat = {
> > +	.reg = (struct mxc_uart *)UART5_BASE,
> > +};
> > +
> > +U_BOOT_DEVICE(mxc_serial) = {
> > +	.name = "serial_mxc",
> > +	.platdata = &mxc_serial_plat,
> > +};
> > diff --git a/board/liebherr/display5/spl.c
> > b/board/liebherr/display5/spl.c new file mode 100644
> > index 0000000000..0a36e656c0
> > --- /dev/null
> > +++ b/board/liebherr/display5/spl.c
> > @@ -0,0 +1,247 @@
> > +/*
> > + * Copyright (C) 2017 DENX Software Engineering
> > + * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
> > + *
> > + * SPDX-License-Identifier:	GPL-2.0+
> > + */
> > +
> > +#include <common.h>
> > +#include <spl.h>
> > +#include <libfdt.h>
> > +#include <asm/io.h>
> > +#include <asm/arch/clock.h>
> > +#include <asm/arch/mx6-ddr.h>
> > +#include <asm/arch/mx6-pins.h>
> > +#include "asm/arch/crm_regs.h"
> > +#include <asm/arch/sys_proto.h>
> > +#include <asm/arch/imx-regs.h>
> > +#include "asm/arch/iomux.h"
> > +#include <asm/mach-imx/iomux-v3.h>
> > +#include <environment.h>
> > +#include <fsl_esdhc.h>
> > +#include <netdev.h>
> > +#include "common.h"
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +static const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
> > +	.dram_sdclk_0 = 0x00000030,
> > +	.dram_sdclk_1 = 0x00000030,
> > +	.dram_cas = 0x00000030,
> > +	.dram_ras = 0x00000030,
> > +	.dram_reset = 0x00000030,
> > +	.dram_sdcke0 = 0x00003000,
> > +	.dram_sdcke1 = 0x00003000,
> > +	.dram_sdba2 = 0x00000000,
> > +	.dram_sdodt0 = 0x00000030,
> > +	.dram_sdodt1 = 0x00000030,
> > +
> > +	.dram_sdqs0 = 0x00000030,
> > +	.dram_sdqs1 = 0x00000030,
> > +	.dram_sdqs2 = 0x00000030,
> > +	.dram_sdqs3 = 0x00000030,
> > +	.dram_sdqs4 = 0x00000030,
> > +	.dram_sdqs5 = 0x00000030,
> > +	.dram_sdqs6 = 0x00000030,
> > +	.dram_sdqs7 = 0x00000030,
> > +
> > +	.dram_dqm0 = 0x00000030,
> > +	.dram_dqm1 = 0x00000030,
> > +	.dram_dqm2 = 0x00000030,
> > +	.dram_dqm3 = 0x00000030,
> > +	.dram_dqm4 = 0x00000030,
> > +	.dram_dqm5 = 0x00000030,
> > +	.dram_dqm6 = 0x00000030,
> > +	.dram_dqm7 = 0x00000030,
> > +};
> > +
> > +static const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
> > +	.grp_ddr_type = 0x000c0000,
> > +	.grp_ddrmode_ctl = 0x00020000,
> > +	.grp_ddrpke = 0x00000000,
> > +	.grp_addds = 0x00000030,
> > +	.grp_ctlds = 0x00000030,
> > +	.grp_ddrmode = 0x00020000,
> > +	.grp_b0ds = 0x00000030,
> > +	.grp_b1ds = 0x00000030,
> > +	.grp_b2ds = 0x00000030,
> > +	.grp_b3ds = 0x00000030,
> > +	.grp_b4ds = 0x00000030,
> > +	.grp_b5ds = 0x00000030,
> > +	.grp_b6ds = 0x00000030,
> > +	.grp_b7ds = 0x00000030,
> > +};
> > +
> > +/* 4x128Mx16.cfg */
> > +static const struct mx6_mmdc_calibration mx6_4x256mx16_mmdc_calib
> > = {
> > +	.p0_mpwldectrl0 = 0x002D0028,
> > +	.p0_mpwldectrl1 = 0x0032002D,
> > +	.p1_mpwldectrl0 = 0x00210036,
> > +	.p1_mpwldectrl1 = 0x0019002E,
> > +	.p0_mpdgctrl0 = 0x4349035C,
> > +	.p0_mpdgctrl1 = 0x0348033D,
> > +	.p1_mpdgctrl0 = 0x43550362,
> > +	.p1_mpdgctrl1 = 0x03520316,
> > +	.p0_mprddlctl = 0x41393940,
> > +	.p1_mprddlctl = 0x3F3A3C47,
> > +	.p0_mpwrdlctl = 0x413A423A,
> > +	.p1_mpwrdlctl = 0x4042483E,
> > +};
> > +
> > +/* MT41K128M16JT-125 (2Gb density) */
> > +static const struct mx6_ddr3_cfg mt41k128m16jt_125 = {
> > +	.mem_speed = 1600,
> > +	.density = 2,
> > +	.width = 16,
> > +	.banks = 8,
> > +	.rowaddr = 14,
> > +	.coladdr = 10,
> > +	.pagesz = 2,
> > +	.trcd = 1375,
> > +	.trcmin = 4875,
> > +	.trasmin = 3500,
> > +};
> > +
> > +static void ccgr_init(void)
> > +{
> > +	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg
> > *)CCM_BASE_ADDR; +
> > +	writel(0x00C03F3F, &ccm->CCGR0);
> > +	writel(0x0030FC3F, &ccm->CCGR1);
> > +	writel(0x0FFFCFC0, &ccm->CCGR2);
> > +	writel(0x3FF00000, &ccm->CCGR3);
> > +	writel(0x00FFF300, &ccm->CCGR4);
> > +	writel(0x0F0000C3, &ccm->CCGR5);
> > +	writel(0x000003FF, &ccm->CCGR6);
> > +}
> > +
> > +static void spl_dram_init(void)
> > +{
> > +	struct mx6_ddr_sysinfo sysinfo = {
> > +		/* width of data bus:0=16,1=32,2=64 */
> > +		.dsize = 2,
> > +		/* config for full 4GB range so that
> > get_mem_size() works */
> > +		.cs_density = 32, /* 32Gb per CS */
> > +		/* single chip select */
> > +		.ncs = 1,
> > +		.cs1_mirror = 0,
> > +		.rtt_wr = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Wr
> > = RZQ/4 */
> > +		.rtt_nom = 2 /*DDR3_RTT_120_OHM*/,	/*
> > RTT_Nom = RZQ/2 */
> > +		.walat = 1,	/* Write additional latency */
> > +		.ralat = 5,	/* Read additional latency */
> > +		.mif3_mode = 3,	/* Command prediction
> > working mode */
> > +		.bi_on = 1,	/* Bank interleaving enabled */
> > +		.sde_to_rst = 0x10,	/* 14 cycles, 200us
> > (JEDEC default) */
> > +		.rst_to_cke = 0x23,	/* 33 cycles, 500us
> > (JEDEC default) */
> > +		.pd_fast_exit = 1, /* enable precharge power-down
> > fast exit */
> > +		.ddr_type = DDR_TYPE_DDR3,
> > +		.refsel = 1,	/* Refresh cycles at 32KHz */
> > +		.refr = 7,	/* 8 refresh commands per
> > refresh cycle */
> > +	};
> > +
> > +	mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
> > +	mx6_dram_cfg(&sysinfo, &mx6_4x256mx16_mmdc_calib,
> > &mt41k128m16jt_125); +}
> > +
> > +#ifdef CONFIG_SPL_SPI_SUPPORT
> > +static void displ5_init_ecspi(void)
> > +{
> > +	displ5_set_iomux_ecspi_spl();
> > +	enable_spi_clk(1, 1);
> > +}
> > +#else
> > +static inline void displ5_init_ecspi(void) { }
> > +#endif
> > +
> > +#ifdef CONFIG_SPL_MMC_SUPPORT
> > +static struct fsl_esdhc_cfg usdhc_cfg = {
> > +	.esdhc_base = USDHC4_BASE_ADDR,
> > +	.max_bus_width = 8,
> > +};
> > +
> > +int board_mmc_init(bd_t *bd)
> > +{
> > +	displ5_set_iomux_usdhc_spl();
> > +
> > +	usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
> > +	gd->arch.sdhc_clk = usdhc_cfg.sdhc_clk;
> > +
> > +	return fsl_esdhc_initialize(bd, &usdhc_cfg);
> > +}
> > +#endif
> > +
> > +void board_init_f(ulong dummy)
> > +{
> > +	ccgr_init();
> > +
> > +	arch_cpu_init();
> > +
> > +	gpr_init();
> > +
> > +	/* setup GP timer */
> > +	timer_init();
> > +
> > +	displ5_set_iomux_uart_spl();
> > +
> > +	/* UART clocks enabled and gd valid - init serial console
> > */
> > +	preloader_console_init();
> > +
> > +	displ5_init_ecspi();
> > +
> > +	/* DDR initialization */
> > +	spl_dram_init();
> > +
> > +	/* Clear the BSS. */
> > +	memset(__bss_start, 0, __bss_end - __bss_start);
> > +
> > +	/* load/boot image from boot device */
> > +	board_init_r(NULL, 0);
> > +}
> > +
> > +void board_boot_order(u32 *spl_boot_list)
> > +{
> > +	/* Default boot sequence SPI -> MMC */
> > +	spl_boot_list[0] = spl_boot_device();
> > +	spl_boot_list[1] = BOOT_DEVICE_MMC1;
> > +	spl_boot_list[2] = BOOT_DEVICE_UART;
> > +	spl_boot_list[3] = BOOT_DEVICE_NONE;
> > +
> > +#ifdef CONFIG_SPL_ENV_SUPPORT
> > +	/* 'fastboot' */
> > +	const char *s;
> > +
> > +	env_init();
> > +	env_load();
> > +
> > +	s = env_get("BOOT_FROM");
> > +	if (s && strcmp(s, "ACTIVE") == 0) {
> > +		spl_boot_list[0] = BOOT_DEVICE_MMC1;
> > +		spl_boot_list[1] = spl_boot_device();
> > +	}
> > +#endif
> > +}
> > +
> > +void reset_cpu(ulong addr) {}
> > +
> > +#ifdef CONFIG_SPL_LOAD_FIT
> > +int board_fit_config_name_match(const char *name)
> > +{
> > +	return 0;
> > +}
> > +#endif
> > +
> > +#ifdef CONFIG_SPL_OS_BOOT
> > +/* Return: 1 - boot to U-Boot. 0 - boot OS (falcon mode) */
> > +int spl_start_uboot(void)
> > +{
> > +	/* break into full u-boot on 'c' */
> > +	if (serial_tstc() && serial_getc() == 'c')
> > +		return 1;
> > +
> > +#ifdef CONFIG_SPL_ENV_SUPPORT
> > +	if (env_get_yesno("boot_os") != 1)
> > +		return 1;
> > +#endif
> > +	return 0;
> > +}
> > +#endif
> > diff --git a/configs/display5_defconfig b/configs/display5_defconfig
> > new file mode 100644
> > index 0000000000..dfd9c2c298
> > --- /dev/null
> > +++ b/configs/display5_defconfig
> > @@ -0,0 +1,62 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_MX6=y
> > +CONFIG_SPL_GPIO_SUPPORT=y
> > +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> > +CONFIG_TARGET_DISPLAY5=y
> > +CONFIG_SPL_MMC_SUPPORT=y
> > +CONFIG_SPL_SERIAL_SUPPORT=y
> > +CONFIG_SPL_SPI_FLASH_SUPPORT=y
> > +CONFIG_SPL_SPI_SUPPORT=y
> > +CONFIG_DEFAULT_DEVICE_TREE="imx6q-display5"
> > +CONFIG_FIT=y
> > +CONFIG_SPL_LOAD_FIT=y
> > +CONFIG_OF_BOARD_SETUP=y
> > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q"
> > +CONFIG_SPL=y
> > +# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
> > +CONFIG_SPL_DMA_SUPPORT=y
> > +CONFIG_SPL_ENV_SUPPORT=y
> > +CONFIG_SPL_SAVEENV=y
> > +CONFIG_SPL_I2C_SUPPORT=y
> > +CONFIG_SPL_OS_BOOT=y
> > +CONFIG_HUSH_PARSER=y
> > +CONFIG_SYS_PROMPT="display5 > "
> > +CONFIG_CMD_BOOTZ=y
> > +# CONFIG_CMD_ELF is not set
> > +CONFIG_CMD_ASKENV=y
> > +CONFIG_CRC32_VERIFY=y
> > +CONFIG_CMD_EEPROM=y
> > +# CONFIG_CMD_FPGA is not set
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_I2C=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_PART=y
> > +CONFIG_CMD_SF=y
> > +CONFIG_CMD_SPI=y
> > +CONFIG_CMD_DHCP=y
> > +CONFIG_CMD_MII=y
> > +CONFIG_CMD_PING=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_CMD_TIME=y
> > +CONFIG_CMD_EXT2=y
> > +CONFIG_CMD_EXT4=y
> > +CONFIG_CMD_FAT=y
> > +CONFIG_CMD_FS_GENERIC=y
> > +CONFIG_CMD_MTDPARTS=y
> > +CONFIG_MTDIDS_DEFAULT="nor0=02008000.spi.1"
> > +CONFIG_MTDPARTS_DEFAULT="mtdparts=02008000.spi.1:128k(SPL),1m(u-boot),64k(env1),64k(env2),8m(lin-recovery),4m(swu-kernel),8m(swu-initramfs),-(reserved)"
> > +CONFIG_EFI_PARTITION=y
> > +# CONFIG_SPL_EFI_PARTITION is not set
> > +CONFIG_OF_CONTROL=y
> > +CONFIG_ENV_IS_IN_SPI_FLASH=y
> > +CONFIG_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_BAR=y
> > +CONFIG_SPI_FLASH_SPANSION=y
> > +CONFIG_SPI_FLASH_STMICRO=y
> > +CONFIG_PHYLIB=y
> > +CONFIG_PHY_MARVELL=y
> > +CONFIG_NETDEVICES=y
> > +CONFIG_FEC_MXC=y
> > +# CONFIG_SPL_DM_SERIAL is not set
> > +CONFIG_MXC_UART=y
> > diff --git a/configs/display5_factory_defconfig
> > b/configs/display5_factory_defconfig new file mode 100644
> > index 0000000000..3f10ffad03
> > --- /dev/null
> > +++ b/configs/display5_factory_defconfig
> > @@ -0,0 +1,76 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_MX6=y
> > +CONFIG_SPL_GPIO_SUPPORT=y
> > +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> > +CONFIG_TARGET_DISPLAY5=y
> > +CONFIG_SPL_SERIAL_SUPPORT=y
> > +CONFIG_SPL_SPI_FLASH_SUPPORT=y
> > +CONFIG_SPL_SPI_SUPPORT=y
> > +CONFIG_FIT=y
> > +CONFIG_OF_BOARD_SETUP=y
> > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q"
> > +CONFIG_BOOTDELAY=3
> > +CONFIG_SPL=y
> > +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
> > +# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
> > +CONFIG_SPL_DMA_SUPPORT=y
> > +CONFIG_SPL_I2C_SUPPORT=y
> > +CONFIG_SPL_OS_BOOT=y
> > +CONFIG_SPL_USB_HOST_SUPPORT=y
> > +CONFIG_SPL_USB_GADGET_SUPPORT=y
> > +CONFIG_SPL_USB_SDP_SUPPORT=y
> > +CONFIG_HUSH_PARSER=y
> > +CONFIG_SYS_PROMPT="display5 factory > "
> > +CONFIG_BOOTCMD_OVERRIDE=y
> > +CONFIG_BOOTCOMMAND="run factory"
> > +CONFIG_CMD_BOOTZ=y
> > +# CONFIG_CMD_ELF is not set
> > +CONFIG_CMD_ASKENV=y
> > +CONFIG_CRC32_VERIFY=y
> > +CONFIG_CMD_EEPROM=y
> > +CONFIG_CMD_DFU=y
> > +# CONFIG_CMD_FPGA is not set
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_GPT=y
> > +CONFIG_CMD_I2C=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_PART=y
> > +CONFIG_CMD_SF=y
> > +CONFIG_CMD_SPI=y
> > +CONFIG_CMD_USB_SDP=y
> > +CONFIG_CMD_DHCP=y
> > +CONFIG_CMD_MII=y
> > +CONFIG_CMD_PING=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_CMD_TIME=y
> > +CONFIG_CMD_EXT2=y
> > +CONFIG_CMD_EXT4=y
> > +CONFIG_CMD_EXT4_WRITE=y
> > +CONFIG_CMD_FAT=y
> > +CONFIG_CMD_FS_GENERIC=y
> > +CONFIG_CMD_MTDPARTS=y
> > +CONFIG_MTDIDS_DEFAULT="nor0=02008000.spi.1"
> > +CONFIG_MTDPARTS_DEFAULT="mtdparts=02008000.spi.1:128k(SPL),1m(u-boot),64k(env1),64k(env2),8m(lin-recovery),4m(swu-kernel),8m(swu-initramfs),-(reserved)"
> > +# CONFIG_SPL_EFI_PARTITION is not set
> > +CONFIG_PARTITION_TYPE_GUID=y
> > +CONFIG_ENV_IS_IN_SPI_FLASH=y
> > +CONFIG_DFU_MMC=y
> > +CONFIG_DFU_SF=y
> > +CONFIG_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_BAR=y
> > +CONFIG_SPI_FLASH_SPANSION=y
> > +CONFIG_SPI_FLASH_STMICRO=y
> > +CONFIG_PHYLIB=y
> > +CONFIG_NETDEVICES=y
> > +CONFIG_FEC_MXC=y
> > +# CONFIG_SPL_DM_SERIAL is not set
> > +CONFIG_MXC_UART=y
> > +CONFIG_USB=y
> > +CONFIG_USB_GADGET=y
> > +CONFIG_USB_GADGET_MANUFACTURER="Liebherr"
> > +CONFIG_USB_GADGET_VENDOR_NUM=0x1b67
> > +CONFIG_USB_GADGET_PRODUCT_NUM=0x4000
> > +CONFIG_CI_UDC=y
> > +CONFIG_USB_GADGET_DOWNLOAD=y
> > +CONFIG_OF_LIBFDT=y
> > diff --git a/include/configs/display5.h b/include/configs/display5.h
> > new file mode 100644
> > index 0000000000..c41ab8b5e2
> > --- /dev/null
> > +++ b/include/configs/display5.h
> > @@ -0,0 +1,408 @@
> > +/*
> > + * Copyright (C) 2017
> > + * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
> > + *
> > + * SPDX-License-Identifier:	GPL-2.0+
> > + */
> > +
> > +#ifndef __CONFIG_H
> > +#define __CONFIG_H
> > +
> > +#include "mx6_common.h"
> > +
> > +/* Falcon Mode */
> > +#define CONFIG_CMD_SPL
> > +#define CONFIG_SYS_SPL_ARGS_ADDR	0x18000000
> > +#define CONFIG_CMD_SPL_WRITE_SIZE	(44 * SZ_1K)
> > +
> > +/* Falcon Mode - MMC support */
> > +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR	0x3F00
> > +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS	\
> > +	(CONFIG_CMD_SPL_WRITE_SIZE / 512)
> > +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
> > 0x100	/* 128KiB */ +
> > +/*
> > + * display5 SPI-NOR memory layout
> > + *
> > + * The definition can be found in Kconfig's
> > + * CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT
> > + *
> > + * 0x000000 - 0x020000 : SPI.SPL (128KiB)
> > + * 0x020000 - 0x120000 : SPI.u-boot (1MiB)
> > + * 0x120000 - 0x130000 : SPI.u-boot-env1 (64KiB)
> > + * 0x130000 - 0x140000 : SPI.u-boot-env2 (64KiB)
> > + * 0x140000 - 0x940000 : SPI.fitImage-recovery (8MiB)
> > + * 0x940000 - 0xD40000 : SPI.swupdate-kernel-FIT (4MiB)
> > + * 0xD40000 - 0x1540000 : SPI.swupdate-initramfs  (8MiB)
> > + */
> > +
> > +#ifndef CONFIG_SPL_BUILD
> > +#define CONFIG_MTD_DEVICE
> > +#define CONFIG_SPI_FLASH_MTD
> > +#define CONFIG_MTD_PARTITIONS
> > +#endif
> > +
> > +/* Below values are "dummy" - only to avoid build break */
> > +#define CONFIG_SYS_SPI_KERNEL_OFFS      0x150000
> > +#define CONFIG_SYS_SPI_ARGS_OFFS        0x140000
> > +#define CONFIG_SYS_SPI_ARGS_SIZE        0x10000
> > +
> > +#include "imx6_spl.h"
> > +#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x20000
> > +#define CONFIG_SPL_SPI_LOAD
> > +
> > +#define CONFIG_CMDLINE_TAG
> > +#define CONFIG_SETUP_MEMORY_TAGS
> > +#define CONFIG_INITRD_TAG
> > +#define CONFIG_REVISION_TAG
> > +
> > +/* Size of malloc() pool */
> > +#define CONFIG_SYS_MALLOC_LEN		(16 * 1024 * 1024)
> > +#define CONFIG_MISC_INIT_R
> > +
> > +/*#define CONFIG_MXC_UART*/
> > +#define CONFIG_MXC_UART_BASE		UART5_BASE
> > +
> > +/* SPI NOR Flash */
> > +#ifdef CONFIG_CMD_SF
> > +#define CONFIG_MXC_SPI
> > +#define CONFIG_SF_DEFAULT_BUS		1
> > +#define CONFIG_SF_DEFAULT_CS		(0 | (IMX_GPIO_NR(5,
> > 29) << 8)) +#define CONFIG_SF_DEFAULT_SPEED		50000000
> > +#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
> > +#endif
> > +
> > +/* I2C Configs */
> > +#define CONFIG_SYS_I2C
> > +#define CONFIG_SYS_I2C_MXC
> > +#define CONFIG_SYS_I2C_MXC_I2C1
> > +#define CONFIG_SYS_I2C_MXC_I2C2
> > +#define CONFIG_SYS_I2C_MXC_I2C3
> > +#define CONFIG_I2C_MULTI_BUS
> > +#define CONFIG_SYS_I2C_SPEED		100000
> > +#define CONFIG_I2C_EDID
> > +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
> > +
> > +/* Ethernet */
> > +#ifdef CONFIG_FEC_MXC
> > +#define IMX_FEC_BASE			ENET_BASE_ADDR
> > +#define CONFIG_FEC_XCV_TYPE		RGMII
> > +#define CONFIG_ETHPRIME			"FEC"
> > +#define CONFIG_FEC_MXC_PHYADDR		0
> > +#define CONFIG_MII
> > +#endif
> > +
> > +/* MMC Configs */
> > +#define CONFIG_FSL_ESDHC
> > +#define CONFIG_FSL_USDHC
> > +#define CONFIG_SYS_FSL_ESDHC_ADDR	0
> > +#define CONFIG_SYS_FSL_USDHC_NUM	2
> > +#define CONFIG_SUPPORT_EMMC_BOOT
> > +
> > +/* allow to overwrite serial and ethaddr */
> > +#define CONFIG_ENV_OVERWRITE
> > +#define CONFIG_BAUDRATE			115200
> > +
> > +#ifndef CONFIG_BOOTCOMMAND
> > +#define CONFIG_BOOTCOMMAND "run boot_mmc"
> > +#endif
> > +
> > +#define PARTS_DEFAULT \
> > +	/* Linux partitions */ \
> > +	"partitions=" \
> > +	"uuid_disk=${uuid_gpt_disk};" \
> > +	"name=kernel_raw1,start=128K,size=8M,uuid=${uuid_gpt_kernel_raw1};"
> > \
> > +	"name=rootfs1,size=1528M,uuid=${uuid_gpt_rootfs1};" \
> > +	"name=kernel_raw2,size=8M,uuid=${uuid_gpt_kernel_raw2};" \
> > +	"name=rootfs2,size=1528M,uuid=${uuid_gpt_rootfs2};" \
> > +	"name=data,size=-,uuid=${uuid_gpt_data}\0"
> > +
> > +#define FACTORY_PROCEDURE \
> > +	"echo '#######################';" \
> > +	"echo '# Factory Boot        #';" \
> > +	"echo '#######################';" \
> > +	"env default -a;" \
> > +	"saveenv;" \
> > +	"gpt write mmc ${mmcdev} ${partitions};" \
> > +	"run tftp_sf_SPL;" \
> > +	"run tftp_sf_uboot;" \
> > +	TFTP_UPDATE_KERNEL \
> > +	"run tftp_sf_fitImg_recovery;" \
> > +	"run tftp_sf_fitImg_SWU;" \
> > +	"run tftp_sf_initramfs_SWU;" \
> > +	TFTP_UPDATE_ROOTFS \
> > +	"echo '#######################';" \
> > +	"echo '# END - OK            #';" \
> > +	"echo '#######################';" \
> > +	"setenv bootcmd 'env default -a; saveenv; run
> > falcon_setup; reset';" \
> > +	"setenv boot_os 'n';" \
> > +	"saveenv;" \
> > +	"reset;"
> > +
> > +#define SWUPDATE_RECOVERY_PROCEDURE \
> > +	"echo '#######################';" \
> > +	"echo '# RECOVERY SWUupdate  #';" \
> > +	"echo '#######################';" \
> > +	"setenv loadaddr_swu_initramfs 0x14000000;" \
> > +	"setenv bootargs console=${console} " \
> > +		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"
> > \
> > +		":${hostname}::off root=/dev/ram rw;" \
> > +	"sf probe;" \
> > +	"sf read ${loadaddr} swu-kernel;" \
> > +	"sf read ${loadaddr_swu_initramfs} swu-initramfs;" \
> > +	"bootm ${loadaddr} ${loadaddr_swu_initramfs};"
> > +
> > +#define KERNEL_RECOVERY_PROCEDURE \
> > +	"echo '#######################';" \
> > +	"echo '# RECOVERY KERNEL IMG #';" \
> > +	"echo '#######################';" \
> > +	"sf probe;" \
> > +	"sf read ${loadaddr} lin-recovery;" \
> > +	"bootm;"
> > +
> > +#define SETUP_BOOTARGS \
> > +	"run set_rootfs_part;" \
> > +	"setenv bootargs ${bootargs} console=${console} "
> > \
> > +		      "root=/dev/mmcblk${mmcdev}p${rootfs_part} " \
> > +		      "rootwait rootfstype=ext4 rw; " \
> > +	"run set_kernel_part;" \
> > +	"part start mmc ${mmcdev} ${kernel_part} lba_start; " \
> > +	"mmc read ${loadaddr} ${lba_start} 0x2000; " \
> > +	"setenv fdt_conf imx6q-${board}-${display}.dtb; "
> > +
> > +/* All the numbers are in LBAs */
> > +#define __TFTP_UPDATE_KERNEL \
> > +	"tftp_mmc_fitImg=" \
> > +	   "if test ! -n ${kernel_part}; then " \
> > +	       "setenv kernel_part ${kernel_part_active};" \
> > +	   "fi;" \
> > +	   "if tftp ${loadaddr} ${kernel_file}; then " \
> > +	       "setexpr fw_sz ${filesize} / 0x200; " \
> > +	       "setexpr fw_sz ${fw_sz} + 1; "  \
> > +	       "part start mmc ${mmcdev} ${kernel_part} lba_start;
> > " \
> > +	       "mmc write ${loadaddr} ${lba_start} ${fw_sz}; " \
> > +	   "; fi\0" \
> > +
> > +#define TFTP_UPDATE_KERNEL \
> > +	"setenv kernel_part ${kernel_part_active};" \
> > +	"run tftp_mmc_fitImg;" \
> > +	"setenv kernel_part ${kernel_part_backup};" \
> > +	"run tftp_mmc_fitImg;" \
> > +
> > +#define __TFTP_UPDATE_ROOTFS \
> > +	"tftp_mmc_rootfs=" \
> > +	   "if test ! -n ${rootfs_part}; then " \
> > +	       "setenv rootfs_part ${rootfs_part_active};" \
> > +	   "fi;" \
> > +	   "if tftp ${loadaddr} ${rootfs_file}; then " \
> > +	       "setexpr fw_sz ${filesize} / 0x200; " \
> > +	       "setexpr fw_sz ${fw_sz} + 1; "  \
> > +	       "part start mmc ${mmcdev} ${rootfs_part} lba_start;
> > " \
> > +	       "mmc write ${loadaddr} ${lba_start} ${fw_sz}; " \
> > +	   "; fi\0" \
> > +
> > +/* To save some considerable time, we only once download the
> > rootfs image */ +/* and store it on 'active' and 'backup' rootfs
> > partitions */ +#define TFTP_UPDATE_ROOTFS \
> > +	"setenv rootfs_part ${rootfs_part_active};" \
> > +	"run tftp_mmc_rootfs;" \
> > +	"part start mmc ${mmcdev} ${rootfs_part_backup}
> > lba_start;" \
> > +	"mmc write ${loadaddr} ${lba_start} ${fw_sz};" \
> > +
> > +#define TFTP_UPDATE_RECOVERY_SWU_KERNEL \
> > +	"tftp_sf_fitImg_SWU=" \
> > +	    "if tftp ${loadaddr} ${kernel_file}; then " \
> > +		"sf probe;" \
> > +		"sf erase swu-kernel +${filesize};" \
> > +		"sf write ${loadaddr} swu-kernel ${filesize};" \
> > +	"; fi\0"	  \
> > +
> > +#define TFTP_UPDATE_RECOVERY_SWU_INITRAMFS \
> > +	"swu_initramfs_file=swupdate-image-display5.ext3.gz.u-boot\0"
> > \
> > +	"tftp_sf_initramfs_SWU=" \
> > +	    "if tftp ${loadaddr} ${swu_initramfs_file}; then " \
> > +		"sf probe;" \
> > +		"sf erase swu-initramfs +${filesize};" \
> > +		"sf write ${loadaddr} swu-initramfs ${filesize};" \
> > +	"; fi\0"	  \
> > +
> > +#define TFTP_UPDATE_RECOVERY_KERNEL_INITRAMFS \
> > +	"kernel_recovery_file=fitImage-initramfs\0" \
> > +	"tftp_sf_fitImg_recovery=" \
> > +	    "if tftp ${loadaddr} ${kernel_recovery_file}; then " \
> > +		"sf probe;" \
> > +		"sf erase lin-recovery +${filesize};" \
> > +		"sf write ${loadaddr} lin-recovery ${filesize};" \
> > +	"; fi\0"	  \
> > +
> > +#define TFTP_UPDATE_BOOTLOADER \
> > +	"ubootfile=u-boot.img\0" \
> > +	"ubootfileSPL=SPL\0" \
> > +	"tftp_sf_uboot=" \
> > +	    "if tftp ${loadaddr} ${ubootfile}; then " \
> > +		"sf probe;" \
> > +		"sf erase u-boot +${filesize};" \
> > +		"sf write ${loadaddr} u-boot ${filesize}" \
> > +	"; fi\0"	  \
> > +	"tftp_sf_SPL="	  \
> > +	    "if tftp ${loadaddr} ${ubootfileSPL}; then " \
> > +		"sf probe;" \
> > +		"setexpr uboot_SPL_size ${filesize} + 0x400;" \
> > +		"sf erase 0x0 +${uboot_SPL_size};" \
> > +		"sf write ${loadaddr} 0x400 ${filesize};" \
> > +	"fi\0" \
> > +
> > +#define CONFIG_EXTRA_ENV_SETTINGS	  \
> > +	PARTS_DEFAULT \
> > +	"display=tianma-tm070-800x480\0" \
> > +	"board=display5\0" \
> > +	"mmcdev=0\0" \
> > +	"altbootcmd=run recovery\0" \
> > +	"bootdelay=1\0" \
> > +	"baudrate=115200\0" \
> > +	"bootcmd=" CONFIG_BOOTCOMMAND "\0" \
> > +	"factory=" FACTORY_PROCEDURE "\0" \
> > +	"bootlimit=3\0" \
> > +	"ethact=FEC\0" \
> > +	"netdev=eth0\0" \
> > +	"boot_os=y\0" \
> > +	"hostname=display5\0" \
> > +	"loadaddr=0x12000000\0" \
> > +	"fdtaddr=0x12800000\0" \
> > +	"console=ttymxc4,115200 quiet\0" \
> > +	"fdtfile=imx6q-display5.dtb\0" \
> > +	"fdt_high=0xffffffff\0" \
> > +	"initrd_high=0xffffffff\0" \
> > +	"kernel_file=fitImage\0" \
> > +	"up=run tftp_sf_SPL; run tftp_sf_uboot\0" \
> > +	"download_kernel=" \
> > +		"tftpboot ${loadaddr} ${kernel_file};\0" \
> > +	"boot_kernel_recovery=" KERNEL_RECOVERY_PROCEDURE "\0" \
> > +	"boot_swu_recovery=" SWUPDATE_RECOVERY_PROCEDURE "\0" \
> > +	"recovery=" \
> > +	"if test ${BOOT_FROM_RECOVERY} = SWU; then " \
> > +	     "echo BOOT: RECOVERY: SWU;" \
> > +	     "run boot_swu_recovery;" \
> > +	"else " \
> > +	     "echo BOOT: RECOVERY: Linux;" \
> > +	     "run boot_kernel_recovery;" \
> > +	"fi\0" \
> > +	"boot_tftp=" \
> > +	"if run download_kernel; then "	  \
> > +	     "setenv bootargs console=${console} " \
> > +	     "root=/dev/mmcblk0p2 rootwait;" \
> > +	     "bootm ${loadaddr} - ${fdtaddr};" \
> > +	"fi\0" \
> > +	"addip=setenv bootargs ${bootargs} " \
> > +	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:" \
> > +	    "${hostname}:eth0:on"	  \
> > +	"\0"	  \
> > +	"nfsargs=setenv bootargs " \
> > +	"root=/dev/nfs rw "	  \
> > +	"nfsroot=${serverip}:${rootpath},nolock,nfsvers=3" \
> > +	"\0" \
> > +	"rootpath=/srv/tftp/DISP5/rootfs\0" \
> > +	"boot_nfs=" \
> > +	"if run download_kernel; then "	  \
> > +	     "run nfsargs;"	  \
> > +	     "run addip;"	  \
> > +	     "setenv bootargs ${bootargs}
> > console=${console};"	  \
> > +	     "setenv fdt_conf imx6q-${board}-${display}.dtb; " \
> > +	     "bootm ${loadaddr}#conf@${fdt_conf};" \
> > +	"fi\0" \
> > +	"falcon_setup=" \
> > +	"if mmc dev ${mmcdev}; then "	  \
> > +	     SETUP_BOOTARGS \
> > +	     "spl export fdt ${loadaddr}#conf@${fdt_conf};" \
> > +	     "setexpr fw_sz ${fdtargslen} / 0x200; " \
> > +	     "setexpr fw_sz ${fw_sz} + 1; "  \
> > +	     "mmc write ${fdtargsaddr} " \
> > +	     __stringify(CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR)"
> > ${fw_sz}; " \
> > +	"fi\0" \
> > +	"boot_mmc=" \
> > +	"if mmc dev ${mmcdev}; then "	  \
> > +	     SETUP_BOOTARGS \
> > +	     "bootm ${loadaddr}#conf@${fdt_conf};" \
> > +	"fi\0" \
> > +	"set_kernel_part=" \
> > +	"if test ${BOOT_FROM} = ACTIVE; then " \
> > +	     "setenv kernel_part ${kernel_part_active};" \
> > +	     "echo BOOT: ACTIVE;" \
> > +	"else if test ${BOOT_FROM} = BACKUP; then " \
> > +	     "setenv kernel_part ${kernel_part_backup};" \
> > +	     "echo BOOT: BACKUP;" \
> > +	"else " \
> > +	     "run recovery;" \
> > +	"fi;fi\0" \
> > +	"set_rootfs_part=" \
> > +	"if test ${BOOT_FROM} = ACTIVE; then " \
> > +	     "setenv rootfs_part ${rootfs_part_active};" \
> > +	"else if test ${BOOT_FROM} = BACKUP; then " \
> > +	     "setenv rootfs_part ${rootfs_part_backup};" \
> > +	"else " \
> > +	     "run recovery;" \
> > +	"fi;fi\0" \
> > +	"BOOT_FROM=ACTIVE\0" \
> > +	"BOOT_FROM_RECOVERY=Linux\0" \
> > +	TFTP_UPDATE_BOOTLOADER \
> > +	"kernel_part_active=1\0" \
> > +	"kernel_part_backup=3\0" \
> > +	__TFTP_UPDATE_KERNEL \
> > +	"rootfs_part_active=2\0" \
> > +	"rootfs_part_backup=4\0" \
> > +	"rootfs_file=core-image-lwn-display5.ext4\0" \
> > +	__TFTP_UPDATE_ROOTFS \
> > +	TFTP_UPDATE_RECOVERY_KERNEL_INITRAMFS \
> > +	TFTP_UPDATE_RECOVERY_SWU_KERNEL \
> > +	TFTP_UPDATE_RECOVERY_SWU_INITRAMFS \
> > +	"\0" \
> > +
> > +/* Miscellaneous configurable options */
> > +#undef CONFIG_SYS_CBSIZE
> > +#define CONFIG_SYS_CBSIZE		2048
> > +
> > +/* Print Buffer Size */
> > +#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
> > +					 sizeof(CONFIG_SYS_PROMPT)
> > + 16) +#define CONFIG_SYS_MAXARGS		32
> > +#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
> > +
> > +#define CONFIG_STANDALONE_LOAD_ADDR	0x10001000
> > +#define CONFIG_SYS_HZ			1000
> > +
> > +/* Physical Memory Map */
> > +#define CONFIG_NR_DRAM_BANKS		1
> > +#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
> > +#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
> > +
> > +#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
> > +#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
> > +
> > +#define CONFIG_SYS_INIT_SP_OFFSET \
> > +	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> > +#define CONFIG_SYS_INIT_SP_ADDR \
> > +	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> > +
> > +/* Commands */
> > +#define CONFIG_MTD_PARTITIONS
> > +#define CONFIG_MTD_DEVICE
> > +
> > +/* ENV config */
> > +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
> > +#define CONFIG_ENV_SIZE		(SZ_64K)
> > +/* The 0x120000 value corresponds to above SPI-NOR memory MAP */
> > +#define CONFIG_ENV_OFFSET		(0x120000)
> > +#define CONFIG_ENV_SECT_SIZE		(SZ_64K)
> > +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
> > +#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
> > +
> > CONFIG_ENV_SECT_SIZE) +#define
> > CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE +
> > +#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
> > +#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
> > +#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
> > +#define CONFIG_ENV_SPI_MAX_HZ
> > CONFIG_SF_DEFAULT_SPEED +#endif
> > +
> > +#define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI |
> > PORT_PTS_PTW) +#endif /* __CONFIG_H */
> >   
> 
> 



Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20171107/4f7c05db/attachment.sig>