On Wed, Jan 03, 2018 at 12:12:06PM +0100, Marcin Wojtas wrote:
> Hi Graeme,
> 
> 2018-01-03 12:00 GMT+01:00 Graeme Gregory <graeme.gregory@linaro.org>:
> > On Mon, Dec 18, 2017 at 10:40:31AM +0100, Ard Biesheuvel wrote:
> >> On 18 December 2017 at 10:17, Marcin Wojtas <mw@semihalf.com> wrote:
> >> > Hi,
> >> >
> >> > This patchset introduces ACPI support in mvpp2 and mvmdio drivers.
> >> > First three patches introduce fwnode helpers for obtaining PHY
> >> > information from nodes and also MDIO fwnode API for registering
> >> > the bus with its PHY/devices.
> >> >
> >> > Following patches update code of the mvmdio and mvpp2 drivers
> >> > to support ACPI tables handling. The latter is done in 4 steps,
> >> > as can be seen in the commits. For the details, please
> >> > refer to the commit messages.
> >> >
> >> > Drivers operation was tested on top of the net-next branch
> >> > with both DT and ACPI. Although for compatibility reasons
> >> > with older platforms, the mvmdio driver keeps using
> >> > of_ MDIO registering, new fwnode_ one proved to fully work
> >> > with DT as well (tested on MacchiatoBin board).
> >> >
> >> > mvpp2/mvmdio driver can work with the ACPI representation, as exposed
> >> > on a public branch:
> >> > https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/marvell-armada-wip
> >> > It was compiled together with the most recent Tianocore EDK2 revision.
> >> > Please refer to the firmware build instruction on MacchiatoBin board:
> >> > http://wiki.macchiatobin.net/tiki-index.php?page=Build+from+source+-+UEFI+EDK+II
> >> >
> >> > Above support configures 1G to use its PHY normally. 10G can work now
> >> > only with the link interrupt mode. Somehow reading of the
> >> > string property in fwnode_mdiobus_child_is_phy works only with
> >> > DT and cannot cope with 10G PHY nodes as in:
> >> > https://pastebin.com/3JnYpU0A
> >> >
> >> > Above root cause will be further checked. In the meantime I will
> >> > appreciate any comments or remarks for the kernel patches.
> >> >
> >>
> >> Hi Marcin,
> >>
> >> I have added linux-acpi and Graeme to cc. I think it makes sense to
> >> discuss the way you describe the device topology before looking at the
> >> patches in more detail.
> >>
> >> In particular, I would like to request feedback on the use of
> >> [redundant] 'reg' properties and the use of _DSD + compatible to
> >> describe PHYs. Usually, we try to avoid this, given that it is
> >> essentially a ACPI encapsulated DT dialect that is difficult to
> >> support in drivers unless they are based on DT to begin with. Also,
> >> non-standard _DSD properties require a vendor prefix, it is not
> >> freeform.
> >>
> >> For reference, the ACPI description is here (starting at line 175)
> >> https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/blob/72d5ac23b20dd74d479daa5e40ba443264b31261/Platforms/Marvell/Armada/AcpiTables/Armada80x0McBin/Dsdt.asl
> >>
> > So the representation of PHY's with _DSD was kind of formalised here
> >
> > http://www.uefi.org/sites/default/files/resources/nic-request-v2.pdf
> >
> > This is already in use in the kernel, and that DSDT seems to be along the same
> > lines. So seems ok in that manner.
> >
> > The "reg", 0 property seems a little odd, it would probably make more
> > sense to check for the lack of ranges passed in in ACPI manner _CRS.
> >
> 
> I already agreed with 'reg' being awkward in the later emails.
> Wouldn't _ADR be more appropriate to specify PHY address on MDIO bus?
> 
Ah it is an actual address, then yes _ADR is probably more appropriate.

Graeme