[PATCH v11 0/7] Enable Bluetooth functionality for WCN3990

[PATCH v11 0/7] Enable Bluetooth functionality for WCN3990

[Balakrishna Godavarthi]

These patches enables Bluetooth functinalties for new Qualcomm
Bluetooth chip wnc3990. As this is latest chip with new features, 
along with some common features to old chip "qcom,qca6174-bt".
we have updated names of functions that are used for both the chips 
to keep this generic and would help in future when we would have new 
BT SoC.

The below are difference between new and old chips.

*Power:
 *New chip: we use voltage regulators to turn on/off the chip and we 
  must send a command on Tx line to turn on/off the chip completely.
 *Old chip: We turn on/off by setting a GPIO.

 *Note: Turning on sequence differs between two chips.

*Firmware download:
  Only firmware file name differ from New and Old chip.
  
  So we reused some functions/structure/variables which are used for old 
  chip to New chip by generic naming (may be future chips may use same functions).

 * As we have multiple changes for functions names,we have tested these patches 
   on both chips.

v11:
 * removed regulator current from dtbindings
 * addressed review comments.

v10:
 * update current load with actual values of WCN3990.
 * added support  for itterative connect with BT chip if it fails to respond to the HOST.
 * Added regulator current dtbindings.
 * addressed review comments.

v9:
 * removed smps regs.
 * hidded flow control in respective functions.
 * moved qca_soc_ver to qca_setup
 * addressed review comments.
 
v8:
  * Squashed [v7 2/8] and [v7 3/8] to one patch.
  * updated functions to set and get the UART speeds.
  * addressed review comments.

v7:
  * Renamed all the possible function of ROME to generic.
  * updated with review comments for hci_qca and btqca
  * fixed kbuild errors.
  * created wrapper functions for re-usable blocks.
 
v6:
  * Hooked up qca_power to qca_serdev.
  * renamed all the naming inconsistency functions with qca_*
  * leveraged common code of ROME for wcn3990.
  * created wrapper functions for re-usable blocks.
  * updated function of _*regulator_enable and _*regualtor_disable.  
  * removed redundant comments and functions.
  * add code to derive the firmware files based on ROM Version.
  * created new patch for common function of ROME and wcn3990.
  * enables Qualcomm chip to operate at 3.2Mbps.
  * updated names of functions that are used for both the chips to keep this generic. 

v5:
  * updated with review comments for hci_qca and btqca
 
v4:
  * rebased all changes on top of bluetooth-next.
  * addressed review comments.
  * New patch created for firmware download.

v3:
  * Rebased all changes on top of bluetooth-next.
  * dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn3990
    - added dt-binding snippet for bluetooth chip wcn3990.
  * Bluetooth: Add support for wcn3990 soc.
    - updated BT_INFO with bt_dev_info, where ever necessary.

v2:
   * Add support for wcn3990:
    These changes are aligned as per serdev frame work.
          We implemented these changes on top of https://patchwork.kernel.org/patch/10316093/
        As this patch enable serdev for one of the Qualcomm BT chip.

        The changes in the patch include.
        - Adding support to voting up/down regulators for WCN3990.
           - Bluetooth firmware download for wcn3990.

  * Add device tree bindings for Atheros chips:
          These changes are on top of https://patchwork.kernel.org/patch/10316097/.
          - Description of device tree bindings.


Balakrishna Godavarthi (7):
  dt-bindings: net: bluetooth: Add device tree bindings for QTI chip
    wcn3990
  Bluetooth: btqca: Rename ROME specific functions to generic functions
  Bluetooth: btqca: Redefine qca_uart_setup() to generic function.
  Bluetooth: hci_qca: Add wrapper functions for setting UART speed
  Bluetooth: hci_qca: Enable 3.2 Mbps operating speed.
  Bluetooth: btqca: Add wcn3990 firmware download support.
  Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990

 .../bindings/net/qualcomm-bluetooth.txt       |  26 +-
 drivers/bluetooth/btqca.c                     | 119 +++--
 drivers/bluetooth/btqca.h                     |  22 +-
 drivers/bluetooth/hci_qca.c                   | 505 ++++++++++++++++--
 4 files changed, 556 insertions(+), 116 deletions(-)

-- 
2.17.1

[PATCH v11 1/7] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn3990

[Balakrishna Godavarthi]

From: Balakrishna Godavarthi <bgodavar@codeaurora.org>

This patch enables regulators for the Qualcomm Bluetooth wcn3990
controller.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v11:
    * removed entries of regulator currents.

Changes in v10:
    * added entry for regulator currents

Changes in v9:
    * updated with latest reg handle and names.
    * updated max-speed definition. 

Changes in v8:
    * Separated the optional entries between two chips

Changes in v7:
    * no change.

Changes in v6:

    * Changed the oper-speed to max-speed.

Changes in v5:

    * Added entry for oper-speed and init-speed.

---
 .../bindings/net/qualcomm-bluetooth.txt       | 26 +++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
index 0ea18a53cc29..2175174415ee 100644
--- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
+++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
@@ -10,12 +10,22 @@ device the slave device is attached to.
 Required properties:
  - compatible: should contain one of the following:
    * "qcom,qca6174-bt"
+   * "qcom,wcn3990-bt"
+
+Optional properties for compatible string qcom,qca6174-bt:
 
-Optional properties:
  - enable-gpios: gpio specifier used to enable chip
  - clocks: clock provided to the controller (SUSCLK_32KHZ)
 
-Example:
+Optional properties for compatible string qcom,wcn3990-bt:
+
+ - vddio-supply: Bluetooth wcn3990 VDD_IO supply regulator handle.
+ - vddxo-supply: Bluetooth wcn3990 VDD_XO supply regulator handle.
+ - vddrf-supply: Bluetooth wcn3990 VDD_RF supply regulator handle.
+ - vddch0-supply: Bluetooth wcn3990 VDD_CH0 supply regulator handle.
+ - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt
+
+Examples:
 
 serial@7570000 {
 	label = "BT-UART";
@@ -28,3 +38,15 @@ serial@7570000 {
 		clocks = <&divclk4>;
 	};
 };
+
+serial@898000 {
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
-- 
2.17.1

[PATCH v11 2/7] Bluetooth: btqca: Rename ROME specific functions to generic functions

[Balakrishna Godavarthi]

From: Balakrishna Godavarthi <bgodavar@codeaurora.org>

Some of the QCA BTSoC ROME functions, are used for different versions
or different make of BTSoC's. Instead of duplicating the same functions
for new chip, update names of the functions that are used for both
chips to keep this generic and would help in future when we would have
new BT SoC. To have generic text in logs updated from ROME to QCA where
ever possible. This avoids confusion to user, when using the future
Qualcomm Bluetooth SoC's. Updated BT_DBG, BT_ERR and BT_INFO with
bt_dev_dbg, bt_dev_err and bt_dev_info where ever applicable.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
 drivers/bluetooth/btqca.c   | 85 ++++++++++++++++++-------------------
 drivers/bluetooth/btqca.h   | 10 ++++-
 drivers/bluetooth/hci_qca.c |  2 +-
 3 files changed, 51 insertions(+), 46 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 8219816c54a0..c5cf9cab438a 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -27,7 +27,7 @@
 
 #define VERSION "0.1"
 
-static int rome_patch_ver_req(struct hci_dev *hdev, u32 *rome_version)
+int qca_read_soc_version(struct hci_dev *hdev, u32 *soc_version)
 {
 	struct sk_buff *skb;
 	struct edl_event_hdr *edl;
@@ -35,36 +35,35 @@ static int rome_patch_ver_req(struct hci_dev *hdev, u32 *rome_version)
 	char cmd;
 	int err = 0;
 
-	BT_DBG("%s: ROME Patch Version Request", hdev->name);
+	bt_dev_dbg(hdev, "QCA Version Request");
 
 	cmd = EDL_PATCH_VER_REQ_CMD;
 	skb = __hci_cmd_sync_ev(hdev, EDL_PATCH_CMD_OPCODE, EDL_PATCH_CMD_LEN,
 				&cmd, HCI_VENDOR_PKT, HCI_INIT_TIMEOUT);
 	if (IS_ERR(skb)) {
 		err = PTR_ERR(skb);
-		BT_ERR("%s: Failed to read version of ROME (%d)", hdev->name,
-		       err);
+		bt_dev_err(hdev, "Reading QCA version information failed (%d)",
+			   err);
 		return err;
 	}
 
 	if (skb->len != sizeof(*edl) + sizeof(*ver)) {
-		BT_ERR("%s: Version size mismatch len %d", hdev->name,
-		       skb->len);
+		bt_dev_err(hdev, "QCA Version size mismatch len %d", skb->len);
 		err = -EILSEQ;
 		goto out;
 	}
 
 	edl = (struct edl_event_hdr *)(skb->data);
 	if (!edl) {
-		BT_ERR("%s: TLV with no header", hdev->name);
+		bt_dev_err(hdev, "QCA TLV with no header");
 		err = -EILSEQ;
 		goto out;
 	}
 
 	if (edl->cresp != EDL_CMD_REQ_RES_EVT ||
 	    edl->rtype != EDL_APP_VER_RES_EVT) {
-		BT_ERR("%s: Wrong packet received %d %d", hdev->name,
-		       edl->cresp, edl->rtype);
+		bt_dev_err(hdev, "QCA Wrong packet received %d %d", edl->cresp,
+			   edl->rtype);
 		err = -EIO;
 		goto out;
 	}
@@ -76,11 +75,11 @@ static int rome_patch_ver_req(struct hci_dev *hdev, u32 *rome_version)
 	BT_DBG("%s: ROM    :0x%08x", hdev->name, le16_to_cpu(ver->rome_ver));
 	BT_DBG("%s: SOC    :0x%08x", hdev->name, le32_to_cpu(ver->soc_id));
 
-	/* ROME chipset version can be decided by patch and SoC
+	/* QCA chipset version can be decided by patch and SoC
 	 * version, combination with upper 2 bytes from SoC
 	 * and lower 2 bytes from patch will be used.
 	 */
-	*rome_version = (le32_to_cpu(ver->soc_id) << 16) |
+	*soc_version = (le32_to_cpu(ver->soc_id) << 16) |
 			(le16_to_cpu(ver->rome_ver) & 0x0000ffff);
 
 out:
@@ -88,18 +87,19 @@ static int rome_patch_ver_req(struct hci_dev *hdev, u32 *rome_version)
 
 	return err;
 }
+EXPORT_SYMBOL_GPL(qca_read_soc_version);
 
-static int rome_reset(struct hci_dev *hdev)
+static int qca_send_reset(struct hci_dev *hdev)
 {
 	struct sk_buff *skb;
 	int err;
 
-	BT_DBG("%s: ROME HCI_RESET", hdev->name);
+	bt_dev_dbg(hdev, "QCA HCI_RESET");
 
 	skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_INIT_TIMEOUT);
 	if (IS_ERR(skb)) {
 		err = PTR_ERR(skb);
-		BT_ERR("%s: Reset failed (%d)", hdev->name, err);
+		bt_dev_err(hdev, "QCA Reset failed (%d)", err);
 		return err;
 	}
 
@@ -108,7 +108,7 @@ static int rome_reset(struct hci_dev *hdev)
 	return 0;
 }
 
-static void rome_tlv_check_data(struct rome_config *config,
+static void qca_tlv_check_data(struct rome_config *config,
 				const struct firmware *fw)
 {
 	const u8 *data;
@@ -207,7 +207,7 @@ static void rome_tlv_check_data(struct rome_config *config,
 	}
 }
 
-static int rome_tlv_send_segment(struct hci_dev *hdev, int seg_size,
+static int qca_tlv_send_segment(struct hci_dev *hdev, int seg_size,
 				 const u8 *data, enum rome_tlv_dnld_mode mode)
 {
 	struct sk_buff *skb;
@@ -228,19 +228,19 @@ static int rome_tlv_send_segment(struct hci_dev *hdev, int seg_size,
 				HCI_VENDOR_PKT, HCI_INIT_TIMEOUT);
 	if (IS_ERR(skb)) {
 		err = PTR_ERR(skb);
-		BT_ERR("%s: Failed to send TLV segment (%d)", hdev->name, err);
+		bt_dev_err(hdev, "QCA Failed to send TLV segment (%d)", err);
 		return err;
 	}
 
 	if (skb->len != sizeof(*edl) + sizeof(*tlv_resp)) {
-		BT_ERR("%s: TLV response size mismatch", hdev->name);
+		bt_dev_err(hdev, "QCA TLV response size mismatch");
 		err = -EILSEQ;
 		goto out;
 	}
 
 	edl = (struct edl_event_hdr *)(skb->data);
 	if (!edl) {
-		BT_ERR("%s: TLV with no header", hdev->name);
+		bt_dev_err(hdev, "TLV with no header");
 		err = -EILSEQ;
 		goto out;
 	}
@@ -249,8 +249,8 @@ static int rome_tlv_send_segment(struct hci_dev *hdev, int seg_size,
 
 	if (edl->cresp != EDL_CMD_REQ_RES_EVT ||
 	    edl->rtype != EDL_TVL_DNLD_RES_EVT || tlv_resp->result != 0x00) {
-		BT_ERR("%s: TLV with error stat 0x%x rtype 0x%x (0x%x)",
-		       hdev->name, edl->cresp, edl->rtype, tlv_resp->result);
+		bt_dev_err(hdev, "QCA TLV with error stat 0x%x rtype 0x%x (0x%x)",
+			   edl->cresp, edl->rtype, tlv_resp->result);
 		err = -EIO;
 	}
 
@@ -260,23 +260,23 @@ static int rome_tlv_send_segment(struct hci_dev *hdev, int seg_size,
 	return err;
 }
 
-static int rome_download_firmware(struct hci_dev *hdev,
+static int qca_download_firmware(struct hci_dev *hdev,
 				  struct rome_config *config)
 {
 	const struct firmware *fw;
 	const u8 *segment;
 	int ret, remain, i = 0;
 
-	bt_dev_info(hdev, "ROME Downloading %s", config->fwname);
+	bt_dev_info(hdev, "QCA Downloading %s", config->fwname);
 
 	ret = request_firmware(&fw, config->fwname, &hdev->dev);
 	if (ret) {
-		BT_ERR("%s: Failed to request file: %s (%d)", hdev->name,
-		       config->fwname, ret);
+		bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+			   config->fwname, ret);
 		return ret;
 	}
 
-	rome_tlv_check_data(config, fw);
+	qca_tlv_check_data(config, fw);
 
 	segment = fw->data;
 	remain = fw->size;
@@ -290,7 +290,7 @@ static int rome_download_firmware(struct hci_dev *hdev,
 		if (!remain || segsize < MAX_SIZE_PER_TLV_SEGMENT)
 			config->dnld_mode = ROME_SKIP_EVT_NONE;
 
-		ret = rome_tlv_send_segment(hdev, segsize, segment,
+		ret = qca_tlv_send_segment(hdev, segsize, segment,
 					    config->dnld_mode);
 		if (ret)
 			break;
@@ -317,8 +317,7 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
 				HCI_VENDOR_PKT, HCI_INIT_TIMEOUT);
 	if (IS_ERR(skb)) {
 		err = PTR_ERR(skb);
-		BT_ERR("%s: Change address command failed (%d)",
-		       hdev->name, err);
+		bt_dev_err(hdev, "QCA Change address command failed (%d)", err);
 		return err;
 	}
 
@@ -328,32 +327,32 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
 }
 EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome);
 
-int qca_uart_setup_rome(struct hci_dev *hdev, uint8_t baudrate)
+int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate)
 {
 	u32 rome_ver = 0;
 	struct rome_config config;
 	int err;
 
-	BT_DBG("%s: ROME setup on UART", hdev->name);
+	bt_dev_dbg(hdev, "QCA setup on UART");
 
 	config.user_baud_rate = baudrate;
 
-	/* Get ROME version information */
-	err = rome_patch_ver_req(hdev, &rome_ver);
+	/* Get QCA version information */
+	err = qca_read_soc_version(hdev, &rome_ver);
 	if (err < 0 || rome_ver == 0) {
-		BT_ERR("%s: Failed to get version 0x%x", hdev->name, err);
+		bt_dev_err(hdev, "QCA Failed to get version %d", err);
 		return err;
 	}
 
-	bt_dev_info(hdev, "ROME controller version 0x%08x", rome_ver);
+	bt_dev_info(hdev, "QCA controller version 0x%08x", rome_ver);
 
 	/* Download rampatch file */
 	config.type = TLV_TYPE_PATCH;
 	snprintf(config.fwname, sizeof(config.fwname), "qca/rampatch_%08x.bin",
 		 rome_ver);
-	err = rome_download_firmware(hdev, &config);
+	err = qca_download_firmware(hdev, &config);
 	if (err < 0) {
-		BT_ERR("%s: Failed to download patch (%d)", hdev->name, err);
+		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
 		return err;
 	}
 
@@ -361,24 +360,24 @@ int qca_uart_setup_rome(struct hci_dev *hdev, uint8_t baudrate)
 	config.type = TLV_TYPE_NVM;
 	snprintf(config.fwname, sizeof(config.fwname), "qca/nvm_%08x.bin",
 		 rome_ver);
-	err = rome_download_firmware(hdev, &config);
+	err = qca_download_firmware(hdev, &config);
 	if (err < 0) {
-		BT_ERR("%s: Failed to download NVM (%d)", hdev->name, err);
+		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
 		return err;
 	}
 
 	/* Perform HCI reset */
-	err = rome_reset(hdev);
+	err = qca_send_reset(hdev);
 	if (err < 0) {
-		BT_ERR("%s: Failed to run HCI_RESET (%d)", hdev->name, err);
+		bt_dev_err(hdev, "QCA Failed to run HCI_RESET (%d)", err);
 		return err;
 	}
 
-	bt_dev_info(hdev, "ROME setup on UART is completed");
+	bt_dev_info(hdev, "QCA setup on UART is completed");
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(qca_uart_setup_rome);
+EXPORT_SYMBOL_GPL(qca_uart_setup);
 
 MODULE_AUTHOR("Ben Young Tae Kim <ytkim@qca.qualcomm.com>");
 MODULE_DESCRIPTION("Bluetooth support for Qualcomm Atheros family ver " VERSION);
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index 13d77fd873b6..5c9851b11838 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -127,7 +127,8 @@ struct tlv_type_hdr {
 #if IS_ENABLED(CONFIG_BT_QCA)
 
 int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr);
-int qca_uart_setup_rome(struct hci_dev *hdev, uint8_t baudrate);
+int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate);
+int qca_read_soc_version(struct hci_dev *hdev, u32 *soc_version);
 
 #else
 
@@ -136,7 +137,12 @@ static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdad
 	return -EOPNOTSUPP;
 }
 
-static inline int qca_uart_setup_rome(struct hci_dev *hdev, int speed)
+static inline int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate)
+{
+	return -EOPNOTSUPP;
+}
+
+static inline int qca_read_soc_version(struct hci_dev *hdev, u32 *soc_version)
 {
 	return -EOPNOTSUPP;
 }
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 51790dd02afb..d7b60669b656 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -966,7 +966,7 @@ static int qca_setup(struct hci_uart *hu)
 	}
 
 	/* Setup patch / NVM configurations */
-	ret = qca_uart_setup_rome(hdev, qca_baudrate);
+	ret = qca_uart_setup(hdev, qca_baudrate);
 	if (!ret) {
 		set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
 		qca_debugfs_init(hdev);
-- 
2.17.1

[PATCH v11 3/7] Bluetooth: btqca: Redefine qca_uart_setup() to generic function.

[Balakrishna Godavarthi]

From: Balakrishna Godavarthi <bgodavar@codeaurora.org>

Redefinition of qca_uart_setup will help future Qualcomm Bluetooth
SoC, to use the same function instead of duplicating the function.
Added new arguments soc_type and soc_ver to the functions.

These arguments will help to decide type of firmware files
to be loaded into Bluetooth chip.
soc_type holds the Bluetooth chip connected to APPS processor.
soc_ver holds the Bluetooth chip version.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
Changes in v11:
      * added error log in qca_read_soc_version() instead of qca_setup() 
---
 drivers/bluetooth/btqca.c   | 23 ++++++++++-------------
 drivers/bluetooth/btqca.h   | 13 +++++++++++--
 drivers/bluetooth/hci_qca.c | 10 +++++++++-
 3 files changed, 30 insertions(+), 16 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index c5cf9cab438a..b2163bf75b95 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -85,6 +85,12 @@ int qca_read_soc_version(struct hci_dev *hdev, u32 *soc_version)
 out:
 	kfree_skb(skb);
 
+	if (!err && *soc_version == 0)
+		err = -EILSEQ;
+
+	if (err)
+		bt_dev_err(hdev, "QCA Failed to get version (%d)", err);
+
 	return err;
 }
 EXPORT_SYMBOL_GPL(qca_read_soc_version);
@@ -327,9 +333,9 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
 }
 EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome);
 
-int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate)
+int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
+		   enum qca_btsoc_type soc_type, u32 soc_ver)
 {
-	u32 rome_ver = 0;
 	struct rome_config config;
 	int err;
 
@@ -337,19 +343,10 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate)
 
 	config.user_baud_rate = baudrate;
 
-	/* Get QCA version information */
-	err = qca_read_soc_version(hdev, &rome_ver);
-	if (err < 0 || rome_ver == 0) {
-		bt_dev_err(hdev, "QCA Failed to get version %d", err);
-		return err;
-	}
-
-	bt_dev_info(hdev, "QCA controller version 0x%08x", rome_ver);
-
 	/* Download rampatch file */
 	config.type = TLV_TYPE_PATCH;
 	snprintf(config.fwname, sizeof(config.fwname), "qca/rampatch_%08x.bin",
-		 rome_ver);
+		 soc_ver);
 	err = qca_download_firmware(hdev, &config);
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
@@ -359,7 +356,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate)
 	/* Download NVM configuration */
 	config.type = TLV_TYPE_NVM;
 	snprintf(config.fwname, sizeof(config.fwname), "qca/nvm_%08x.bin",
-		 rome_ver);
+		 soc_ver);
 	err = qca_download_firmware(hdev, &config);
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index 5c9851b11838..a9c2779f3e07 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -124,10 +124,18 @@ struct tlv_type_hdr {
 	__u8   data[0];
 } __packed;
 
+enum qca_btsoc_type {
+	QCA_INVALID = -1,
+	QCA_AR3002,
+	QCA_ROME,
+	QCA_WCN3990
+};
+
 #if IS_ENABLED(CONFIG_BT_QCA)
 
 int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr);
-int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate);
+int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
+		   enum qca_btsoc_type soc_type, u32 soc_ver);
 int qca_read_soc_version(struct hci_dev *hdev, u32 *soc_version);
 
 #else
@@ -137,7 +145,8 @@ static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdad
 	return -EOPNOTSUPP;
 }
 
-static inline int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate)
+static inline int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
+				 enum qca_btsoc_type soc_type, u32 soc_ver)
 {
 	return -EOPNOTSUPP;
 }
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index d7b60669b656..5f1c0a8fd5cd 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -929,6 +929,7 @@ static int qca_setup(struct hci_uart *hu)
 	struct qca_data *qca = hu->priv;
 	unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200;
 	int ret;
+	int soc_ver = 0;
 
 	bt_dev_info(hdev, "ROME setup");
 
@@ -965,8 +966,15 @@ static int qca_setup(struct hci_uart *hu)
 		host_set_baudrate(hu, speed);
 	}
 
+	/* Get QCA version information */
+	ret = qca_read_soc_version(hdev, &soc_ver);
+	if (ret)
+		return ret;
+
+	bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
+
 	/* Setup patch / NVM configurations */
-	ret = qca_uart_setup(hdev, qca_baudrate);
+	ret = qca_uart_setup(hdev, qca_baudrate, QCA_ROME, soc_ver);
 	if (!ret) {
 		set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
 		qca_debugfs_init(hdev);
-- 
2.17.1

[PATCH v11 4/7] Bluetooth: hci_qca: Add wrapper functions for setting UART speed

[Balakrishna Godavarthi]

From: Balakrishna Godavarthi <bgodavar@codeaurora.org>

In function qca_setup, we set initial and operating speeds for Qualcomm
Bluetooth SoC's. This block of code is common across different
Qualcomm Bluetooth SoC's. Instead of duplicating the code, created
a wrapper function to set the speeds. So that future coming SoC's
can use these wrapper functions to set speeds.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
 drivers/bluetooth/hci_qca.c | 93 ++++++++++++++++++++++++++++---------
 1 file changed, 70 insertions(+), 23 deletions(-)

diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 5f1c0a8fd5cd..5f8a74d65bec 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -119,6 +119,11 @@ struct qca_data {
 	u64 votes_off;
 };
 
+enum qca_speed_type {
+	QCA_INIT_SPEED = 1,
+	QCA_OPER_SPEED
+};
+
 struct qca_serdev {
 	struct hci_uart	 serdev_hu;
 	struct gpio_desc *bt_en;
@@ -923,6 +928,61 @@ static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed)
 		hci_uart_set_baudrate(hu, speed);
 }
 
+static unsigned int qca_get_speed(struct hci_uart *hu,
+				  enum qca_speed_type speed_type)
+{
+	unsigned int speed = 0;
+
+	if (speed_type == QCA_INIT_SPEED) {
+		if (hu->init_speed)
+			speed = hu->init_speed;
+		else if (hu->proto->init_speed)
+			speed = hu->proto->init_speed;
+	} else {
+		if (hu->oper_speed)
+			speed = hu->oper_speed;
+		else if (hu->proto->oper_speed)
+			speed = hu->proto->oper_speed;
+	}
+
+	return speed;
+}
+
+static int qca_check_speeds(struct hci_uart *hu)
+{
+	if (!qca_get_speed(hu, QCA_INIT_SPEED) ||
+	    !qca_get_speed(hu, QCA_OPER_SPEED))
+		return -EINVAL;
+
+	return 0;
+}
+
+static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
+{
+	unsigned int speed, qca_baudrate;
+	int ret;
+
+	if (speed_type == QCA_INIT_SPEED) {
+		speed = qca_get_speed(hu, QCA_INIT_SPEED);
+		if (speed)
+			host_set_baudrate(hu, speed);
+	} else {
+		speed = qca_get_speed(hu, QCA_OPER_SPEED);
+		if (!speed)
+			return 0;
+
+		qca_baudrate = qca_get_baudrate_value(speed);
+		bt_dev_info(hu->hdev, "Set UART speed to %d", speed);
+		ret = qca_set_baudrate(hu->hdev, qca_baudrate);
+		if (ret)
+			return ret;
+
+		host_set_baudrate(hu, speed);
+	}
+
+	return 0;
+}
+
 static int qca_setup(struct hci_uart *hu)
 {
 	struct hci_dev *hdev = hu->hdev;
@@ -933,37 +993,24 @@ static int qca_setup(struct hci_uart *hu)
 
 	bt_dev_info(hdev, "ROME setup");
 
+	ret = qca_check_speeds(hu);
+	if (ret)
+		return ret;
+
 	/* Patch downloading has to be done without IBS mode */
 	clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
 
 	/* Setup initial baudrate */
-	speed = 0;
-	if (hu->init_speed)
-		speed = hu->init_speed;
-	else if (hu->proto->init_speed)
-		speed = hu->proto->init_speed;
-
-	if (speed)
-		host_set_baudrate(hu, speed);
+	qca_set_speed(hu, QCA_INIT_SPEED);
 
 	/* Setup user speed if needed */
-	speed = 0;
-	if (hu->oper_speed)
-		speed = hu->oper_speed;
-	else if (hu->proto->oper_speed)
-		speed = hu->proto->oper_speed;
-
+	speed = qca_get_speed(hu, QCA_OPER_SPEED);
 	if (speed) {
-		qca_baudrate = qca_get_baudrate_value(speed);
-
-		bt_dev_info(hdev, "Set UART speed to %d", speed);
-		ret = qca_set_baudrate(hdev, qca_baudrate);
-		if (ret) {
-			bt_dev_err(hdev, "Failed to change the baud rate (%d)",
-				   ret);
+		ret = qca_set_speed(hu, QCA_OPER_SPEED);
+		if (ret)
 			return ret;
-		}
-		host_set_baudrate(hu, speed);
+
+		qca_baudrate = qca_get_baudrate_value(speed);
 	}
 
 	/* Get QCA version information */
-- 
2.17.1

[PATCH v11 5/7] Bluetooth: hci_qca: Enable 3.2 Mbps operating speed.

[Balakrishna Godavarthi]

From: Balakrishna Godavarthi <bgodavar@codeaurora.org>

Enable Qualcomm chips to operate at 3.2Mbps.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
 drivers/bluetooth/hci_qca.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 5f8a74d65bec..a6e7d38ef931 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -877,6 +877,8 @@ static uint8_t qca_get_baudrate_value(int speed)
 		return QCA_BAUDRATE_2000000;
 	case 3000000:
 		return QCA_BAUDRATE_3000000;
+	case 3200000:
+		return QCA_BAUDRATE_3200000;
 	case 3500000:
 		return QCA_BAUDRATE_3500000;
 	default:
@@ -891,7 +893,7 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
 	struct sk_buff *skb;
 	u8 cmd[] = { 0x01, 0x48, 0xFC, 0x01, 0x00 };
 
-	if (baudrate > QCA_BAUDRATE_3000000)
+	if (baudrate > QCA_BAUDRATE_3200000)
 		return -EINVAL;
 
 	cmd[4] = baudrate;
-- 
2.17.1

[PATCH v11 6/7] Bluetooth: btqca: Add wcn3990 firmware download support.

[Balakrishna Godavarthi]

From: Balakrishna Godavarthi <bgodavar@codeaurora.org>

This patch enables the RAM and NV patch download for wcn3990.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
 drivers/bluetooth/btqca.c | 25 +++++++++++++++++++++----
 1 file changed, 21 insertions(+), 4 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index b2163bf75b95..211318671775 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -338,6 +338,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 {
 	struct rome_config config;
 	int err;
+	u8 rom_ver;
 
 	bt_dev_dbg(hdev, "QCA setup on UART");
 
@@ -345,8 +346,19 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 
 	/* Download rampatch file */
 	config.type = TLV_TYPE_PATCH;
-	snprintf(config.fwname, sizeof(config.fwname), "qca/rampatch_%08x.bin",
-		 soc_ver);
+	if (soc_type == QCA_WCN3990) {
+		/* Firmware files to download are based on ROM version.
+		 * ROM version is derived from last two bytes of soc_ver.
+		 */
+		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
+			    (soc_ver & 0x0000000f);
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/crbtfw%02x.tlv", rom_ver);
+	} else {
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/rampatch_%08x.bin", soc_ver);
+	}
+
 	err = qca_download_firmware(hdev, &config);
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
@@ -355,8 +367,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 
 	/* Download NVM configuration */
 	config.type = TLV_TYPE_NVM;
-	snprintf(config.fwname, sizeof(config.fwname), "qca/nvm_%08x.bin",
-		 soc_ver);
+	if (soc_type == QCA_WCN3990)
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/crnv%02x.bin", rom_ver);
+	else
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/nvm_%08x.bin", soc_ver);
+
 	err = qca_download_firmware(hdev, &config);
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
-- 
2.17.1

[PATCH v11 7/7] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990

[Balakrishna Godavarthi]

From: Balakrishna Godavarthi <bgodavar@codeaurora.org>

Add support to set voltage/current of various regulators
to power up/down Bluetooth chip wcn3990.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
---
Changes in v11:
    * removed support to read regulator currents from dts.	
    * updated review comments.

Changes in v10:
    * added support to read regulator currents from dts.
    * added support to try to connect with chip if it fails to respond to initial commands
    * updated review comments.

changes in v9:
    * moved flow control to vendor and set_baudarte functions.
    * removed parent regs.

changes in v8:
    * closing qca buffer, if qca_power_setup fails
    * chnaged ibs start timer function call location.
    * updated review comments.
  
changes in v7:
    * addressed review comments.

changes in v6:
    * Hooked up qca_power to qca_serdev.
    * renamed all the naming inconsistency functions with qca_*
    * leveraged common code of ROME for wcn3990.
    * created wrapper functions for re-usable blocks.
    * updated function of _*regulator_enable and _*regualtor_disable.  
    * removed redundant comments and functions.
    * addressed review comments.

Changes in v5:
    * updated regulator vddpa min_uV to 1304000.
      * addressed review comments.
 
Changes in v4:
    * Segregated the changes of btqca from hci_qca
    * rebased all changes on top of bluetooth-next.
    * addressed review comments.
---
 drivers/bluetooth/btqca.h   |   3 +
 drivers/bluetooth/hci_qca.c | 424 ++++++++++++++++++++++++++++++++----
 2 files changed, 380 insertions(+), 47 deletions(-)

diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index a9c2779f3e07..0c01f375fe83 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -37,6 +37,9 @@
 #define EDL_TAG_ID_HCI			(17)
 #define EDL_TAG_ID_DEEP_SLEEP		(27)
 
+#define QCA_WCN3990_POWERON_PULSE	0xFC
+#define QCA_WCN3990_POWEROFF_PULSE	0xC0
+
 enum qca_bardrate {
 	QCA_BAUDRATE_115200 	= 0,
 	QCA_BAUDRATE_57600,
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index a6e7d38ef931..66e7930436d5 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -5,7 +5,7 @@
  *  protocol extension to H4.
  *
  *  Copyright (C) 2007 Texas Instruments, Inc.
- *  Copyright (c) 2010, 2012 The Linux Foundation. All rights reserved.
+ *  Copyright (c) 2010, 2012, 2018 The Linux Foundation. All rights reserved.
  *
  *  Acknowledgements:
  *  This file is based on hci_ll.c, which was...
@@ -31,9 +31,14 @@
 #include <linux/kernel.h>
 #include <linux/clk.h>
 #include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/device.h>
 #include <linux/gpio/consumer.h>
 #include <linux/mod_devicetable.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
 #include <linux/serdev.h>
 
 #include <net/bluetooth/bluetooth.h>
@@ -124,12 +129,46 @@ enum qca_speed_type {
 	QCA_OPER_SPEED
 };
 
+/*
+ * Voltage regulator information required for configuring the
+ * QCA Bluetooth chipset
+ */
+struct qca_vreg {
+	const char *name;
+	unsigned int min_uV;
+	unsigned int max_uV;
+	unsigned int load_uA;
+};
+
+struct qca_vreg_data {
+	enum qca_btsoc_type soc_type;
+	struct qca_vreg *vregs;
+	size_t num_vregs;
+};
+
+/*
+ * Platform data for the QCA Bluetooth power driver.
+ */
+struct qca_power {
+	struct device *dev;
+	const struct qca_vreg_data *vreg_data;
+	struct regulator_bulk_data *vreg_bulk;
+	bool vregs_on;
+};
+
 struct qca_serdev {
 	struct hci_uart	 serdev_hu;
 	struct gpio_desc *bt_en;
 	struct clk	 *susclk;
+	enum qca_btsoc_type btsoc_type;
+	struct qca_power *bt_power;
+	u32 init_speed;
+	u32 oper_speed;
 };
 
+static int qca_power_setup(struct hci_uart *hu, bool on);
+static void qca_power_shutdown(struct hci_dev *hdev);
+
 static void __serial_clock_on(struct tty_struct *tty)
 {
 	/* TODO: Some chipset requires to enable UART clock on client
@@ -407,6 +446,7 @@ static int qca_open(struct hci_uart *hu)
 {
 	struct qca_serdev *qcadev;
 	struct qca_data *qca;
+	int ret;
 
 	BT_DBG("hu %p qca_open", hu);
 
@@ -458,19 +498,32 @@ static int qca_open(struct hci_uart *hu)
 
 	hu->priv = qca;
 
-	timer_setup(&qca->wake_retrans_timer, hci_ibs_wake_retrans_timeout, 0);
-	qca->wake_retrans = IBS_WAKE_RETRANS_TIMEOUT_MS;
-
-	timer_setup(&qca->tx_idle_timer, hci_ibs_tx_idle_timeout, 0);
-	qca->tx_idle_delay = IBS_TX_IDLE_TIMEOUT_MS;
-
 	if (hu->serdev) {
 		serdev_device_open(hu->serdev);
 
 		qcadev = serdev_device_get_drvdata(hu->serdev);
-		gpiod_set_value_cansleep(qcadev->bt_en, 1);
+		if (qcadev->btsoc_type != QCA_WCN3990) {
+			gpiod_set_value_cansleep(qcadev->bt_en, 1);
+		} else {
+			hu->init_speed = qcadev->init_speed;
+			hu->oper_speed = qcadev->oper_speed;
+			ret = qca_power_setup(hu, true);
+			if (ret) {
+				destroy_workqueue(qca->workqueue);
+				kfree_skb(qca->rx_skb);
+				hu->priv = NULL;
+				kfree(qca);
+				return ret;
+			}
+		}
 	}
 
+	timer_setup(&qca->wake_retrans_timer, hci_ibs_wake_retrans_timeout, 0);
+	qca->wake_retrans = IBS_WAKE_RETRANS_TIMEOUT_MS;
+
+	timer_setup(&qca->tx_idle_timer, hci_ibs_tx_idle_timeout, 0);
+	qca->tx_idle_delay = IBS_TX_IDLE_TIMEOUT_MS;
+
 	BT_DBG("HCI_UART_QCA open, tx_idle_delay=%u, wake_retrans=%u",
 	       qca->tx_idle_delay, qca->wake_retrans);
 
@@ -554,10 +607,13 @@ static int qca_close(struct hci_uart *hu)
 	qca->hu = NULL;
 
 	if (hu->serdev) {
-		serdev_device_close(hu->serdev);
-
 		qcadev = serdev_device_get_drvdata(hu->serdev);
-		gpiod_set_value_cansleep(qcadev->bt_en, 0);
+		if (qcadev->btsoc_type == QCA_WCN3990)
+			qca_power_shutdown(hu->hdev);
+		else
+			gpiod_set_value_cansleep(qcadev->bt_en, 0);
+
+		serdev_device_close(hu->serdev);
 	}
 
 	kfree_skb(qca->rx_skb);
@@ -891,6 +947,7 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
 	struct hci_uart *hu = hci_get_drvdata(hdev);
 	struct qca_data *qca = hu->priv;
 	struct sk_buff *skb;
+	struct qca_serdev *qcadev;
 	u8 cmd[] = { 0x01, 0x48, 0xFC, 0x01, 0x00 };
 
 	if (baudrate > QCA_BAUDRATE_3200000)
@@ -904,6 +961,13 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
 		return -ENOMEM;
 	}
 
+	/* Disabling hardware flow control is mandatory while
+	 * sending change baudrate request to wcn3990 SoC.
+	 */
+	qcadev = serdev_device_get_drvdata(hu->serdev);
+	if (qcadev->btsoc_type == QCA_WCN3990)
+		hci_uart_set_flow_control(hu, true);
+
 	/* Assign commands to change baudrate and packet type. */
 	skb_put_data(skb, cmd, sizeof(cmd));
 	hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
@@ -919,6 +983,9 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
 	schedule_timeout(msecs_to_jiffies(BAUDRATE_SETTLE_TIMEOUT_MS));
 	set_current_state(TASK_RUNNING);
 
+	if (qcadev->btsoc_type == QCA_WCN3990)
+		hci_uart_set_flow_control(hu, false);
+
 	return 0;
 }
 
@@ -930,6 +997,43 @@ static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed)
 		hci_uart_set_baudrate(hu, speed);
 }
 
+static int qca_send_power_pulse(struct hci_dev *hdev, u8 cmd)
+{
+	struct hci_uart *hu = hci_get_drvdata(hdev);
+	struct qca_data *qca = hu->priv;
+	struct sk_buff *skb;
+
+	/* These power pulses are single byte command which are sent
+	 * at required baudrate to wcn3990. On wcn3990, we have an external
+	 * circuit at Tx pin which decodes the pulse sent at specific baudrate.
+	 * For example, wcn3990 supports RF COEX antenna for both Wi-Fi/BT
+	 * and also we use the same power inputs to turn on and off for
+	 * Wi-Fi/BT. Powering up the power sources will not enable BT, until
+	 * we send a power on pulse at 115200 bps. This algorithm will help to
+	 * save power. Disabling hardware flow control is mandatory while
+	 * sending power pulses to SoC.
+	 */
+	bt_dev_dbg(hdev, "sending power pulse %02x to SoC", cmd);
+
+	skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL);
+	if (!skb)
+		return -ENOMEM;
+
+	hci_uart_set_flow_control(hu, true);
+
+	skb_put_u8(skb, cmd);
+	hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
+
+	skb_queue_tail(&qca->txq, skb);
+	hci_uart_tx_wakeup(hu);
+
+	/* Wait for 100 uS for SoC to settle down */
+	usleep_range(100, 200);
+	hci_uart_set_flow_control(hu, false);
+
+	return 0;
+}
+
 static unsigned int qca_get_speed(struct hci_uart *hu,
 				  enum qca_speed_type speed_type)
 {
@@ -952,9 +1056,18 @@ static unsigned int qca_get_speed(struct hci_uart *hu,
 
 static int qca_check_speeds(struct hci_uart *hu)
 {
-	if (!qca_get_speed(hu, QCA_INIT_SPEED) ||
-	    !qca_get_speed(hu, QCA_OPER_SPEED))
-		return -EINVAL;
+	struct qca_serdev *qcadev;
+
+	qcadev = serdev_device_get_drvdata(hu->serdev);
+	if (qcadev->btsoc_type == QCA_WCN3990) {
+		if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
+		    !qca_get_speed(hu, QCA_OPER_SPEED))
+			return -EINVAL;
+	} else {
+		if (!qca_get_speed(hu, QCA_INIT_SPEED) ||
+		    !qca_get_speed(hu, QCA_OPER_SPEED))
+			return -EINVAL;
+	}
 
 	return 0;
 }
@@ -974,7 +1087,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
 			return 0;
 
 		qca_baudrate = qca_get_baudrate_value(speed);
-		bt_dev_info(hu->hdev, "Set UART speed to %d", speed);
+		bt_dev_dbg(hu->hdev, "Set UART speed to %d", speed);
 		ret = qca_set_baudrate(hu->hdev, qca_baudrate);
 		if (ret)
 			return ret;
@@ -985,15 +1098,73 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
 	return 0;
 }
 
+static int qca_wcn3990_init(struct hci_uart *hu, u32 *soc_ver)
+{
+	struct hci_dev *hdev = hu->hdev;
+	int i, ret;
+
+	/* wcn3990 is a discrete Bluetooth chip connected to SoC.
+	 * sometimes we will face communication synchronization issues,
+	 * like reading version command timeouts. In which HCI_SETUP fails,
+	 * to overcome these issues, we try to communicate by performing an
+	 * cold power off and on.
+	 */
+	for (i = 0; i <= 3; i++) {
+		ret = qca_power_setup(hu, true);
+		if (ret)
+			goto regs_off;
+
+		/* Forcefully enable wcn3990 to enter in to boot mode. */
+		host_set_baudrate(hu, 2400);
+		ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWEROFF_PULSE);
+		if (ret)
+			goto regs_off;
+
+		qca_set_speed(hu, QCA_INIT_SPEED);
+		ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWERON_PULSE);
+		if (ret)
+			goto regs_off;
+
+		/* Wait for 100 ms for SoC to boot */
+		msleep(100);
+
+		/* Now the device is in ready state to communicate with host.
+		 * To sync host with device we need to reopen port.
+		 * Without this, we will have RTS and CTS synchronization
+		 * issues.
+		 */
+		serdev_device_close(hu->serdev);
+		ret = serdev_device_open(hu->serdev);
+		if (ret) {
+			bt_dev_err(hu->hdev, "failed to open port");
+			break;
+		}
+
+		hci_uart_set_flow_control(hu, false);
+		ret = qca_read_soc_version(hdev, soc_ver);
+
+		if (!ret)
+			break;
+
+regs_off:
+		bt_dev_err(hdev, "retrying to establish communication: %d",
+			   i + 1);
+		qca_power_shutdown(hdev);
+	}
+
+	return ret;
+}
+
 static int qca_setup(struct hci_uart *hu)
 {
 	struct hci_dev *hdev = hu->hdev;
 	struct qca_data *qca = hu->priv;
 	unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200;
+	struct qca_serdev *qcadev;
 	int ret;
 	int soc_ver = 0;
 
-	bt_dev_info(hdev, "ROME setup");
+	qcadev = serdev_device_get_drvdata(hu->serdev);
 
 	ret = qca_check_speeds(hu);
 	if (ret)
@@ -1002,8 +1173,15 @@ static int qca_setup(struct hci_uart *hu)
 	/* Patch downloading has to be done without IBS mode */
 	clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
 
-	/* Setup initial baudrate */
-	qca_set_speed(hu, QCA_INIT_SPEED);
+	if (qcadev->btsoc_type == QCA_WCN3990) {
+		bt_dev_info(hdev, "setting up wcn3990");
+		ret = qca_wcn3990_init(hu, &soc_ver);
+		if (ret)
+			return ret;
+	} else {
+		bt_dev_info(hdev, "ROME setup");
+		qca_set_speed(hu, QCA_INIT_SPEED);
+	}
 
 	/* Setup user speed if needed */
 	speed = qca_get_speed(hu, QCA_OPER_SPEED);
@@ -1015,15 +1193,16 @@ static int qca_setup(struct hci_uart *hu)
 		qca_baudrate = qca_get_baudrate_value(speed);
 	}
 
-	/* Get QCA version information */
-	ret = qca_read_soc_version(hdev, &soc_ver);
-	if (ret)
-		return ret;
+	if (qcadev->btsoc_type != QCA_WCN3990) {
+		/* Get QCA version information */
+		ret = qca_read_soc_version(hdev, &soc_ver);
+		if (ret)
+			return ret;
+	}
 
 	bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
-
 	/* Setup patch / NVM configurations */
-	ret = qca_uart_setup(hdev, qca_baudrate, QCA_ROME, soc_ver);
+	ret = qca_uart_setup(hdev, qca_baudrate, qcadev->btsoc_type, soc_ver);
 	if (!ret) {
 		set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
 		qca_debugfs_init(hdev);
@@ -1059,9 +1238,123 @@ static struct hci_uart_proto qca_proto = {
 	.dequeue	= qca_dequeue,
 };
 
+static const struct qca_vreg_data qca_soc_data = {
+	.soc_type = QCA_WCN3990,
+	.vregs = (struct qca_vreg []) {
+		{ "vddio",   1800000, 1900000,  15000  },
+		{ "vddxo",   1800000, 1900000,  80000  },
+		{ "vddrf",   1300000, 1350000,  300000 },
+		{ "vddch0",  3300000, 3400000,  450000 },
+	},
+	.num_vregs = 4,
+};
+
+static void qca_power_shutdown(struct hci_dev *hdev)
+{
+	struct hci_uart *hu = hci_get_drvdata(hdev);
+
+	host_set_baudrate(hu, 2400);
+	qca_send_power_pulse(hdev, QCA_WCN3990_POWEROFF_PULSE);
+	qca_power_setup(hu, false);
+}
+
+static int qca_enable_regulator(struct qca_vreg vregs,
+				struct regulator *regulator)
+{
+	int ret;
+
+	ret = regulator_set_voltage(regulator, vregs.min_uV,
+				    vregs.max_uV);
+	if (ret)
+		return ret;
+
+	if (vregs.load_uA)
+		ret = regulator_set_load(regulator,
+					 vregs.load_uA);
+
+	if (ret)
+		return ret;
+
+	return regulator_enable(regulator);
+
+}
+
+static void qca_disable_regulator(struct qca_vreg vregs,
+				  struct regulator *regulator)
+{
+	regulator_disable(regulator);
+	regulator_set_voltage(regulator, 0, vregs.max_uV);
+	if (vregs.load_uA)
+		regulator_set_load(regulator, 0);
+
+}
+
+static int qca_power_setup(struct hci_uart *hu, bool on)
+{
+	struct qca_vreg *vregs;
+	struct regulator_bulk_data *vreg_bulk;
+	struct qca_serdev *qcadev;
+	int i, num_vregs, ret = 0;
+
+	qcadev = serdev_device_get_drvdata(hu->serdev);
+	if (!qcadev || !qcadev->bt_power || !qcadev->bt_power->vreg_data ||
+	    !qcadev->bt_power->vreg_bulk)
+		return -EINVAL;
+
+	vregs = qcadev->bt_power->vreg_data->vregs;
+	vreg_bulk = qcadev->bt_power->vreg_bulk;
+	num_vregs = qcadev->bt_power->vreg_data->num_vregs;
+	BT_DBG("on: %d", on);
+	if (on  && !qcadev->bt_power->vregs_on) {
+		for (i = 0; i < num_vregs; i++) {
+			ret = qca_enable_regulator(vregs[i],
+						   vreg_bulk[i].consumer);
+			if (ret)
+				break;
+		}
+
+		if (ret) {
+			BT_ERR("failed to enable regulator:%s", vregs[i].name);
+			/* turn off regulators which are enabled */
+			for (i = i - 1; i >= 0; i--)
+				qca_disable_regulator(vregs[i],
+						      vreg_bulk[i].consumer);
+		} else {
+			qcadev->bt_power->vregs_on = true;
+		}
+	} else if (!on && qcadev->bt_power->vregs_on) {
+		/* turn off regulator in reverse order */
+		i = qcadev->bt_power->vreg_data->num_vregs - 1;
+		for ( ; i >= 0; i--)
+			qca_disable_regulator(vregs[i], vreg_bulk[i].consumer);
+
+		qcadev->bt_power->vregs_on = false;
+	}
+
+	return ret;
+}
+
+static int qca_init_regulators(struct qca_power *qca,
+				const struct qca_vreg *vregs, size_t num_vregs)
+{
+	int i;
+
+	qca->vreg_bulk = devm_kzalloc(qca->dev, num_vregs *
+				      sizeof(struct regulator_bulk_data),
+				      GFP_KERNEL);
+	if (!qca->vreg_bulk)
+		return -ENOMEM;
+
+	for (i = 0; i < num_vregs; i++)
+		qca->vreg_bulk[i].supply = vregs[i].name;
+
+	return devm_regulator_bulk_get(qca->dev, num_vregs, qca->vreg_bulk);
+}
+
 static int qca_serdev_probe(struct serdev_device *serdev)
 {
 	struct qca_serdev *qcadev;
+	const struct qca_vreg_data *data;
 	int err;
 
 	qcadev = devm_kzalloc(&serdev->dev, sizeof(*qcadev), GFP_KERNEL);
@@ -1069,47 +1362,84 @@ static int qca_serdev_probe(struct serdev_device *serdev)
 		return -ENOMEM;
 
 	qcadev->serdev_hu.serdev = serdev;
+	data = of_device_get_match_data(&serdev->dev);
 	serdev_device_set_drvdata(serdev, qcadev);
+	if (data && data->soc_type == QCA_WCN3990) {
+		qcadev->btsoc_type = QCA_WCN3990;
+		qcadev->bt_power = devm_kzalloc(&serdev->dev,
+						sizeof(struct qca_power),
+						GFP_KERNEL);
+		if (!qcadev->bt_power)
+			return -ENOMEM;
+
+		qcadev->bt_power->dev = &serdev->dev;
+		qcadev->bt_power->vreg_data = data;
+		err = qca_init_regulators(qcadev->bt_power, data->vregs,
+					  data->num_vregs);
+		if (err) {
+			BT_ERR("Failed to init regulators:%d", err);
+			goto out;
+		}
 
-	qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable",
-				       GPIOD_OUT_LOW);
-	if (IS_ERR(qcadev->bt_en)) {
-		dev_err(&serdev->dev, "failed to acquire enable gpio\n");
-		return PTR_ERR(qcadev->bt_en);
-	}
+		qcadev->bt_power->vregs_on = false;
 
-	qcadev->susclk = devm_clk_get(&serdev->dev, NULL);
-	if (IS_ERR(qcadev->susclk)) {
-		dev_err(&serdev->dev, "failed to acquire clk\n");
-		return PTR_ERR(qcadev->susclk);
-	}
+		device_property_read_u32(&serdev->dev, "max-speed",
+					 &qcadev->oper_speed);
+		if (!qcadev->oper_speed)
+			BT_DBG("UART will pick default operating speed");
 
-	err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ);
-	if (err)
-		return err;
+		err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto);
+		if (err) {
+			BT_ERR("wcn3990 serdev registration failed");
+			goto out;
+		}
+	} else {
+		qcadev->btsoc_type = QCA_ROME;
+		qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable",
+					       GPIOD_OUT_LOW);
+		if (IS_ERR(qcadev->bt_en)) {
+			dev_err(&serdev->dev, "failed to acquire enable gpio\n");
+			return PTR_ERR(qcadev->bt_en);
+		}
 
-	err = clk_prepare_enable(qcadev->susclk);
-	if (err)
-		return err;
+		qcadev->susclk = devm_clk_get(&serdev->dev, NULL);
+		if (IS_ERR(qcadev->susclk)) {
+			dev_err(&serdev->dev, "failed to acquire clk\n");
+			return PTR_ERR(qcadev->susclk);
+		}
 
-	err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto);
-	if (err)
-		clk_disable_unprepare(qcadev->susclk);
+		err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ);
+		if (err)
+			return err;
+
+		err = clk_prepare_enable(qcadev->susclk);
+		if (err)
+			return err;
+
+		err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto);
+		if (err)
+			clk_disable_unprepare(qcadev->susclk);
+	}
+
+out:	return err;
 
-	return err;
 }
 
 static void qca_serdev_remove(struct serdev_device *serdev)
 {
 	struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
 
-	hci_uart_unregister_device(&qcadev->serdev_hu);
+	if (qcadev->btsoc_type == QCA_WCN3990)
+		qca_power_shutdown(qcadev->serdev_hu.hdev);
+	else
+		clk_disable_unprepare(qcadev->susclk);
 
-	clk_disable_unprepare(qcadev->susclk);
+	hci_uart_unregister_device(&qcadev->serdev_hu);
 }
 
 static const struct of_device_id qca_bluetooth_of_match[] = {
 	{ .compatible = "qcom,qca6174-bt" },
+	{ .compatible = "qcom,wcn3990-bt", .data = &qca_soc_data},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
-- 
2.17.1

Re: [PATCH v11 3/7] Bluetooth: btqca: Redefine qca_uart_setup() to generic function.

[Matthias Kaehlcke]

On Fri, Jul 27, 2018 at 07:43:16PM +0530, Balakrishna Godavarthi wrote:
> From: Balakrishna Godavarthi <bgodavar@codeaurora.org>
> 
> Redefinition of qca_uart_setup will help future Qualcomm Bluetooth
> SoC, to use the same function instead of duplicating the function.
> Added new arguments soc_type and soc_ver to the functions.
> 
> These arguments will help to decide type of firmware files
> to be loaded into Bluetooth chip.
> soc_type holds the Bluetooth chip connected to APPS processor.
> soc_ver holds the Bluetooth chip version.
> 
> Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
> ---
> Changes in v11:
>       * added error log in qca_read_soc_version() instead of qca_setup() 
> ---
>  drivers/bluetooth/btqca.c   | 23 ++++++++++-------------
>  drivers/bluetooth/btqca.h   | 13 +++++++++++--
>  drivers/bluetooth/hci_qca.c | 10 +++++++++-
>  3 files changed, 30 insertions(+), 16 deletions(-)
> 
> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> index c5cf9cab438a..b2163bf75b95 100644
> --- a/drivers/bluetooth/btqca.c
> +++ b/drivers/bluetooth/btqca.c
> @@ -85,6 +85,12 @@ int qca_read_soc_version(struct hci_dev *hdev, u32 *soc_version)
>  out:
>  	kfree_skb(skb);
>  
> +	if (!err && *soc_version == 0)
> +		err = -EILSEQ;

nit: better do this right after assigning SoC version. No need to
respin the series just for this though.

Re: [PATCH v11 7/7] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990

[Matthias Kaehlcke]

On Fri, Jul 27, 2018 at 07:43:20PM +0530, Balakrishna Godavarthi wrote:
> From: Balakrishna Godavarthi <bgodavar@codeaurora.org>
> 
> Add support to set voltage/current of various regulators
> to power up/down Bluetooth chip wcn3990.
> 
> Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
> ---
> Changes in v11:
>     * removed support to read regulator currents from dts.	
>     * updated review comments.

Updated regulator voltage ranges?

> +static int qca_wcn3990_init(struct hci_uart *hu, u32 *soc_ver)
> +{
> +	struct hci_dev *hdev = hu->hdev;
> +	int i, ret;
> +
> +	/* wcn3990 is a discrete Bluetooth chip connected to SoC.
> +	 * sometimes we will face communication synchronization issues,
> +	 * like reading version command timeouts. In which HCI_SETUP fails,
> +	 * to overcome these issues, we try to communicate by performing an
> +	 * cold power off and on.
> +	 */
> +	for (i = 0; i <= 3; i++) {
> +		ret = qca_power_setup(hu, true);
> +		if (ret)
> +			goto regs_off;
> +
> +		/* Forcefully enable wcn3990 to enter in to boot mode. */
> +		host_set_baudrate(hu, 2400);
> +		ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWEROFF_PULSE);
> +		if (ret)
> +			goto regs_off;
> +
> +		qca_set_speed(hu, QCA_INIT_SPEED);
> +		ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWERON_PULSE);
> +		if (ret)
> +			goto regs_off;
> +
> +		/* Wait for 100 ms for SoC to boot */
> +		msleep(100);
> +
> +		/* Now the device is in ready state to communicate with host.
> +		 * To sync host with device we need to reopen port.
> +		 * Without this, we will have RTS and CTS synchronization
> +		 * issues.
> +		 */
> +		serdev_device_close(hu->serdev);
> +		ret = serdev_device_open(hu->serdev);
> +		if (ret) {
> +			bt_dev_err(hu->hdev, "failed to open port");
> +			break;
> +		}
> +
> +		hci_uart_set_flow_control(hu, false);
> +		ret = qca_read_soc_version(hdev, soc_ver);
> +
> +		if (!ret)
> +			break;
> +
> +regs_off:
> +		bt_dev_err(hdev, "retrying to establish communication: %d",
> +			   i + 1);
> +		qca_power_shutdown(hdev);
> +	}
> +
> +	return ret;
> +}

I'm still not convinced that the retry loop is needed/desirable, I
commented on the discussion on v10.

> +static const struct qca_vreg_data qca_soc_data = {
> +	.soc_type = QCA_WCN3990,
> +	.vregs = (struct qca_vreg []) {
> +		{ "vddio",   1800000, 1900000,  15000  },
> +		{ "vddxo",   1800000, 1900000,  80000  },
> +		{ "vddrf",   1300000, 1350000,  300000 },
> +		{ "vddch0",  3300000, 3400000,  450000 },
> +	},

In v10 this was:

		{ "vddio",   1800000, 1800000,  15000  },
		{ "vddxo",   1800000, 1800000,  80000  },
		{ "vddrf",   1304000, 1304000,  300000 },
		{ "vddch0",  3000000, 3312000,  450000 },

I don't have concerns about the new voltage ranges, but you should
mention such changes in the changelog, ideally with a brief
description why the change was made.

Re: [PATCH v11 3/7] Bluetooth: btqca: Redefine qca_uart_setup() to generic function.

[Balakrishna Godavarthi]

Hi Matthias,

On 2018-07-31 00:07, Matthias Kaehlcke wrote:
> On Fri, Jul 27, 2018 at 07:43:16PM +0530, Balakrishna Godavarthi wrote:
>> From: Balakrishna Godavarthi <bgodavar@codeaurora.org>
>> 
>> Redefinition of qca_uart_setup will help future Qualcomm Bluetooth
>> SoC, to use the same function instead of duplicating the function.
>> Added new arguments soc_type and soc_ver to the functions.
>> 
>> These arguments will help to decide type of firmware files
>> to be loaded into Bluetooth chip.
>> soc_type holds the Bluetooth chip connected to APPS processor.
>> soc_ver holds the Bluetooth chip version.
>> 
>> Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
>> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
>> ---
>> Changes in v11:
>>       * added error log in qca_read_soc_version() instead of 
>> qca_setup()
>> ---
>>  drivers/bluetooth/btqca.c   | 23 ++++++++++-------------
>>  drivers/bluetooth/btqca.h   | 13 +++++++++++--
>>  drivers/bluetooth/hci_qca.c | 10 +++++++++-
>>  3 files changed, 30 insertions(+), 16 deletions(-)
>> 
>> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
>> index c5cf9cab438a..b2163bf75b95 100644
>> --- a/drivers/bluetooth/btqca.c
>> +++ b/drivers/bluetooth/btqca.c
>> @@ -85,6 +85,12 @@ int qca_read_soc_version(struct hci_dev *hdev, u32 
>> *soc_version)
>>  out:
>>  	kfree_skb(skb);
>> 
>> +	if (!err && *soc_version == 0)
>> +		err = -EILSEQ;
> 
> nit: better do this right after assigning SoC version. No need to
> respin the series just for this though.

[Bala]: will update.

-- 
Regards
Balakrishna.

Re: [PATCH v11 7/7] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990

[Balakrishna Godavarthi]

Hi Matthias,

On 2018-07-31 02:25, Matthias Kaehlcke wrote:
> On Fri, Jul 27, 2018 at 07:43:20PM +0530, Balakrishna Godavarthi wrote:
>> From: Balakrishna Godavarthi <bgodavar@codeaurora.org>
>> 
>> Add support to set voltage/current of various regulators
>> to power up/down Bluetooth chip wcn3990.
>> 
>> Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
>> ---
>> Changes in v11:
>>     * removed support to read regulator currents from dts.
>>     * updated review comments.
> 
> Updated regulator voltage ranges?
> 
>> +static int qca_wcn3990_init(struct hci_uart *hu, u32 *soc_ver)
>> +{
>> +	struct hci_dev *hdev = hu->hdev;
>> +	int i, ret;
>> +
>> +	/* wcn3990 is a discrete Bluetooth chip connected to SoC.
>> +	 * sometimes we will face communication synchronization issues,
>> +	 * like reading version command timeouts. In which HCI_SETUP fails,
>> +	 * to overcome these issues, we try to communicate by performing an
>> +	 * cold power off and on.
>> +	 */
>> +	for (i = 0; i <= 3; i++) {
>> +		ret = qca_power_setup(hu, true);
>> +		if (ret)
>> +			goto regs_off;
>> +
>> +		/* Forcefully enable wcn3990 to enter in to boot mode. */
>> +		host_set_baudrate(hu, 2400);
>> +		ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWEROFF_PULSE);
>> +		if (ret)
>> +			goto regs_off;
>> +
>> +		qca_set_speed(hu, QCA_INIT_SPEED);
>> +		ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWERON_PULSE);
>> +		if (ret)
>> +			goto regs_off;
>> +
>> +		/* Wait for 100 ms for SoC to boot */
>> +		msleep(100);
>> +
>> +		/* Now the device is in ready state to communicate with host.
>> +		 * To sync host with device we need to reopen port.
>> +		 * Without this, we will have RTS and CTS synchronization
>> +		 * issues.
>> +		 */
>> +		serdev_device_close(hu->serdev);
>> +		ret = serdev_device_open(hu->serdev);
>> +		if (ret) {
>> +			bt_dev_err(hu->hdev, "failed to open port");
>> +			break;
>> +		}
>> +
>> +		hci_uart_set_flow_control(hu, false);
>> +		ret = qca_read_soc_version(hdev, soc_ver);
>> +
>> +		if (!ret)
>> +			break;
>> +
>> +regs_off:
>> +		bt_dev_err(hdev, "retrying to establish communication: %d",
>> +			   i + 1);
>> +		qca_power_shutdown(hdev);
>> +	}
>> +
>> +	return ret;
>> +}
> 
> I'm still not convinced that the retry loop is needed/desirable, I
> commented on the discussion on v10.
> 
[Bala] : replied on v10 patch.

>> +static const struct qca_vreg_data qca_soc_data = {
>> +	.soc_type = QCA_WCN3990,
>> +	.vregs = (struct qca_vreg []) {
>> +		{ "vddio",   1800000, 1900000,  15000  },
>> +		{ "vddxo",   1800000, 1900000,  80000  },
>> +		{ "vddrf",   1300000, 1350000,  300000 },
>> +		{ "vddch0",  3300000, 3400000,  450000 },
>> +	},
> 
> In v10 this was:
> 
> 		{ "vddio",   1800000, 1800000,  15000  },
> 		{ "vddxo",   1800000, 1800000,  80000  },
> 		{ "vddrf",   1304000, 1304000,  300000 },
> 		{ "vddch0",  3000000, 3312000,  450000 },
> 
> I don't have concerns about the new voltage ranges, but you should
> mention such changes in the changelog, ideally with a brief
> description why the change was made.

[Bala]: I missed to add, I just updated with latest values from 
datasheet.

-- 
Regards
Balakrishna.