[PATCH v3 0/9] TVP5150 fixes and new features

[PATCH v3 0/9] TVP5150 fixes and new features

[Marco Felsch]

Hi,

this is my v3 with the integrated reviews from my v2 [1]. This serie
applies to Mauro's experimental.git [2].

@Mauro:
Patch ("media: tvp5150: fix irq_request error path during probe") is new
in this series. Maybe you can squash them with ("media: tvp5150: Add sync lock
interrupt handling"), thanks.

I've tested this series on a customer dt-based board. Unfortunately I
haven't a device which use the em28xx driver. So other tester a welcome :)

[1] https://www.spinics.net/lists/devicetree/msg244129.html
[2] https://git.linuxtv.org/mchehab/experimental.git/log/?h=tvp5150-4

Javier Martinez Canillas (1):
  partial revert of "[media] tvp5150: add HW input connectors support"

Marco Felsch (7):
  media: tvp5150: fix irq_request error path during probe
  media: tvp5150: add input source selection of_graph support
  media: dt-bindings: tvp5150: Add input port connectors DT bindings
  media: v4l2-subdev: add stubs for v4l2_subdev_get_try_*
  media: v4l2-subdev: fix v4l2_subdev_get_try_* dependency
  media: tvp5150: add FORMAT_TRY support for get/set selection handlers
  media: tvp5150: add s_power callback

Michael Tretter (1):
  media: tvp5150: initialize subdev before parsing device tree

 .../devicetree/bindings/media/i2c/tvp5150.txt |  92 ++-
 drivers/media/i2c/tvp5150.c                   | 657 +++++++++++++-----
 include/dt-bindings/media/tvp5150.h           |   2 -
 include/media/v4l2-subdev.h                   |  15 +-
 4 files changed, 584 insertions(+), 182 deletions(-)

-- 
2.19.0

[PATCH v3 1/9] partial revert of "[media] tvp5150: add HW input connectors support"

[Marco Felsch]

From: Javier Martinez Canillas <javierm@redhat.com>

Commit f7b4b54e6364 ("[media] tvp5150: add HW input connectors support")
added input signals support for the tvp5150, but the approach was found
to be incorrect so the corresponding DT binding commit 82c2ffeb217a
("[media] tvp5150: document input connectors DT bindings") was reverted.

This left the driver with an undocumented (and wrong) DT parsing logic,
so lets get rid of this code as well until the input connectors support
is implemented properly.

It's a partial revert due other patches added on top of mentioned commit
not allowing the commit to be reverted cleanly anymore. But all the code
related to the DT parsing logic and input entities creation are removed.

Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[m.felsch@pengutronix.de: rm TVP5150_INPUT_NUM define]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
---
 drivers/media/i2c/tvp5150.c         | 141 ----------------------------
 include/dt-bindings/media/tvp5150.h |   2 -
 2 files changed, 143 deletions(-)

diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
index ace1f0f5f8cd..133073518744 100644
--- a/drivers/media/i2c/tvp5150.c
+++ b/drivers/media/i2c/tvp5150.c
@@ -53,8 +53,6 @@ struct tvp5150 {
 	struct v4l2_subdev sd;
 #ifdef CONFIG_MEDIA_CONTROLLER
 	struct media_pad pads[TVP5150_NUM_PADS];
-	struct media_entity input_ent[TVP5150_INPUT_NUM];
-	struct media_pad input_pad[TVP5150_INPUT_NUM];
 #endif
 	struct v4l2_ctrl_handler hdl;
 	struct v4l2_rect rect;
@@ -1170,40 +1168,6 @@ static int tvp5150_enum_frame_size(struct v4l2_subdev *sd,
 	return 0;
 }
 
-/****************************************************************************
-			Media entity ops
- ****************************************************************************/
-
-#ifdef CONFIG_MEDIA_CONTROLLER
-static int tvp5150_link_setup(struct media_entity *entity,
-			      const struct media_pad *local,
-			      const struct media_pad *remote, u32 flags)
-{
-	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
-	struct tvp5150 *decoder = to_tvp5150(sd);
-	int i;
-
-	for (i = 0; i < TVP5150_INPUT_NUM; i++) {
-		if (remote->entity == &decoder->input_ent[i])
-			break;
-	}
-
-	/* Do nothing for entities that are not input connectors */
-	if (i == TVP5150_INPUT_NUM)
-		return 0;
-
-	decoder->input = i;
-
-	tvp5150_selmux(sd);
-
-	return 0;
-}
-
-static const struct media_entity_operations tvp5150_sd_media_ops = {
-	.link_setup = tvp5150_link_setup,
-};
-#endif
-
 /****************************************************************************
 			I2C Command
  ****************************************************************************/
@@ -1351,42 +1315,6 @@ static int tvp5150_g_tuner(struct v4l2_subdev *sd, struct v4l2_tuner *vt)
 	return 0;
 }
 
-static int tvp5150_registered(struct v4l2_subdev *sd)
-{
-#ifdef CONFIG_MEDIA_CONTROLLER
-	struct tvp5150 *decoder = to_tvp5150(sd);
-	int ret = 0;
-	int i;
-
-	for (i = 0; i < TVP5150_INPUT_NUM; i++) {
-		struct media_entity *input = &decoder->input_ent[i];
-		struct media_pad *pad = &decoder->input_pad[i];
-
-		if (!input->name)
-			continue;
-
-		decoder->input_pad[i].flags = MEDIA_PAD_FL_SOURCE;
-
-		ret = media_entity_pads_init(input, 1, pad);
-		if (ret < 0)
-			return ret;
-
-		ret = media_device_register_entity(sd->v4l2_dev->mdev, input);
-		if (ret < 0)
-			return ret;
-
-		ret = media_create_pad_link(input, 0, &sd->entity,
-					    TVP5150_PAD_IF_INPUT, 0);
-		if (ret < 0) {
-			media_device_unregister_entity(input);
-			return ret;
-		}
-	}
-#endif
-
-	return 0;
-}
-
 /* ----------------------------------------------------------------------- */
 
 static const struct v4l2_ctrl_ops tvp5150_ctrl_ops = {
@@ -1440,10 +1368,6 @@ static const struct v4l2_subdev_ops tvp5150_ops = {
 	.pad = &tvp5150_pad_ops,
 };
 
-static const struct v4l2_subdev_internal_ops tvp5150_internal_ops = {
-	.registered = tvp5150_registered,
-};
-
 /****************************************************************************
 			I2C Client & Driver
  ****************************************************************************/
@@ -1596,12 +1520,6 @@ static int tvp5150_parse_dt(struct tvp5150 *decoder, struct device_node *np)
 {
 	struct v4l2_fwnode_endpoint bus_cfg;
 	struct device_node *ep;
-#ifdef CONFIG_MEDIA_CONTROLLER
-	struct device_node *connectors, *child;
-	struct media_entity *input;
-	const char *name;
-	u32 input_type;
-#endif
 	unsigned int flags;
 	int ret = 0;
 
@@ -1625,63 +1543,6 @@ static int tvp5150_parse_dt(struct tvp5150 *decoder, struct device_node *np)
 
 	decoder->mbus_type = bus_cfg.bus_type;
 
-#ifdef CONFIG_MEDIA_CONTROLLER
-	connectors = of_get_child_by_name(np, "connectors");
-
-	if (!connectors)
-		goto err;
-
-	for_each_available_child_of_node(connectors, child) {
-		ret = of_property_read_u32(child, "input", &input_type);
-		if (ret) {
-			dev_err(decoder->sd.dev,
-				 "missing type property in node %pOFn\n",
-				 child);
-			goto err_connector;
-		}
-
-		if (input_type >= TVP5150_INPUT_NUM) {
-			ret = -EINVAL;
-			goto err_connector;
-		}
-
-		input = &decoder->input_ent[input_type];
-
-		/* Each input connector can only be defined once */
-		if (input->name) {
-			dev_err(decoder->sd.dev,
-				 "input %s with same type already exists\n",
-				 input->name);
-			ret = -EINVAL;
-			goto err_connector;
-		}
-
-		switch (input_type) {
-		case TVP5150_COMPOSITE0:
-		case TVP5150_COMPOSITE1:
-			input->function = MEDIA_ENT_F_CONN_COMPOSITE;
-			break;
-		case TVP5150_SVIDEO:
-			input->function = MEDIA_ENT_F_CONN_SVIDEO;
-			break;
-		}
-
-		input->flags = MEDIA_ENT_FL_CONNECTOR;
-
-		ret = of_property_read_string(child, "label", &name);
-		if (ret < 0) {
-			dev_err(decoder->sd.dev,
-				 "missing label property in node %pOFn\n",
-				 child);
-			goto err_connector;
-		}
-
-		input->name = name;
-	}
-
-err_connector:
-	of_node_put(connectors);
-#endif
 err:
 	of_node_put(ep);
 	return ret;
@@ -1733,7 +1594,6 @@ static int tvp5150_probe(struct i2c_client *c,
 	}
 
 	v4l2_i2c_subdev_init(sd, c, &tvp5150_ops);
-	sd->internal_ops = &tvp5150_internal_ops;
 	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
 
 #if defined(CONFIG_MEDIA_CONTROLLER)
@@ -1748,7 +1608,6 @@ static int tvp5150_probe(struct i2c_client *c,
 	if (res < 0)
 		return res;
 
-	sd->entity.ops = &tvp5150_sd_media_ops;
 #endif
 
 	res = tvp5150_detect_version(core);
diff --git a/include/dt-bindings/media/tvp5150.h b/include/dt-bindings/media/tvp5150.h
index c852a35e916e..8637910aae76 100644
--- a/include/dt-bindings/media/tvp5150.h
+++ b/include/dt-bindings/media/tvp5150.h
@@ -26,8 +26,6 @@
 #define TVP5150_COMPOSITE1 1
 #define TVP5150_SVIDEO     2
 
-#define TVP5150_INPUT_NUM  3
-
 /* TVP5150 HW outputs */
 #define TVP5150_NORMAL       0
 #define TVP5150_BLACK_SCREEN 1
-- 
2.19.0

[PATCH v3 2/9] media: tvp5150: fix irq_request error path during probe

[Marco Felsch]

Commit 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")
introduced the interrupt handling. But we have to free the
v4l2_ctrl_handler before we can return the error code.

Fixes: 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
 drivers/media/i2c/tvp5150.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
index 133073518744..40aaa8ca0b63 100644
--- a/drivers/media/i2c/tvp5150.c
+++ b/drivers/media/i2c/tvp5150.c
@@ -1650,7 +1650,7 @@ static int tvp5150_probe(struct i2c_client *c,
 						tvp5150_isr, IRQF_TRIGGER_HIGH |
 						IRQF_ONESHOT, "tvp5150", core);
 		if (res)
-			return res;
+			goto err;
 	}
 
 	res = v4l2_async_register_subdev(sd);
-- 
2.19.0

[PATCH v3 3/9] media: tvp5150: add input source selection of_graph support

[Marco Felsch]

This patch adds the of_graph support to describe the tvp connections.
Physical the TVP5150 has three ports: AIP1A, AIP1B and YOUT. As result
of discussion [1],[2] the device-tree maps these ports 1:1. The svideo
connector must be conneted to port@0/endpoint@1, look at the Documentation
for more information. Since the TVP5150 is a converter the device-tree
must contain at least 1-input and 1-output port. The mc-connectors and
mc-links are only created if the device-tree contains the corresponding
connector nodes. If more than one connector is available the
media_entity_operations.link_setup() callback ensures that only one
connector is active.

[1] https://www.spinics.net/lists/linux-media/msg138545.html
[2] https://www.spinics.net/lists/linux-media/msg138546.html

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
Changelog:

v3:
- probe(): s/err/err_free_v4l2_ctrls
- drop MC dependency for tvp5150_pads

v2:
- adapt commit message
- unify ifdef switches
- rename tvp5150_valid_input -> tvp5150_of_valid_input, to be more precise
- mc: use 2-input and 1-output pad
- mc: link svideo connector to both input pads
- mc: enable/disable svideo links in one go
- mc: change link_setup() behaviour, switch the input src don't require a
      explicite disable before.
- mc: rename 'local' media_pad param to tvp5150_pad to avoid confusion
- mc: enable link to the first available connector and set the
      corresponding tvp5150 input src per default during registered()
- mc/of: factor out oftree connector allocation
- of: drop svideo dt port
- of: move svideo connector to port@0/endpoint@1
- of: require at least 1-in and 1-out endpoint

 drivers/media/i2c/tvp5150.c | 485 +++++++++++++++++++++++++++++++++---
 1 file changed, 444 insertions(+), 41 deletions(-)

diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
index 40aaa8ca0b63..40ecbce03e2c 100644
--- a/drivers/media/i2c/tvp5150.c
+++ b/drivers/media/i2c/tvp5150.c
@@ -44,15 +44,38 @@ MODULE_PARM_DESC(debug, "Debug level (0-2)");
 #define dprintk0(__dev, __arg...) dev_dbg_lvl(__dev, 0, 0, __arg)
 
 enum tvp5150_pads {
-       TVP5150_PAD_IF_INPUT,
-       TVP5150_PAD_VID_OUT,
-       TVP5150_NUM_PADS
+	TVP5150_PAD_AIP1A = TVP5150_COMPOSITE0,
+	TVP5150_PAD_AIP1B,
+	TVP5150_PAD_VID_OUT,
+	TVP5150_NUM_PADS
 };
 
+#if defined(CONFIG_MEDIA_CONTROLLER)
+enum tvp5150_pads_state {
+	TVP5150_PAD_INACTIVE,
+	TVP5150_PAD_ACTIVE_COMPOSITE,
+	TVP5150_PAD_ACTIVE_SVIDEO,
+};
+
+struct tvp5150_connector {
+	struct media_entity ent;
+	struct media_pad pad;
+	unsigned int port_num;
+	bool is_svideo;
+};
+#endif
+
 struct tvp5150 {
 	struct v4l2_subdev sd;
-#ifdef CONFIG_MEDIA_CONTROLLER
+	/* additional additional endpoint for the svideo connector */
+	struct device_node *endpoints[TVP5150_NUM_PADS + 1];
+	unsigned int endpoints_num;
+#if defined(CONFIG_MEDIA_CONTROLLER)
 	struct media_pad pads[TVP5150_NUM_PADS];
+	int pads_state[TVP5150_NUM_PADS];
+	struct tvp5150_connector *connectors;
+	int connectors_num;
+	bool modify_second_link;
 #endif
 	struct v4l2_ctrl_handler hdl;
 	struct v4l2_rect rect;
@@ -1168,6 +1191,160 @@ static int tvp5150_enum_frame_size(struct v4l2_subdev *sd,
 	return 0;
 }
 
+/****************************************************************************
+ *			Media entity ops
+ ****************************************************************************/
+#if defined(CONFIG_MEDIA_CONTROLLER)
+static int tvp5150_active_pad_idx(struct tvp5150 *decoder)
+{
+	int *pad_state = &decoder->pads_state[0];
+	int i, idx = -1;
+
+	for (i = 0; i < TVP5150_NUM_PADS - 1; i++) {
+		if ((pad_state[i] == TVP5150_PAD_ACTIVE_COMPOSITE) ||
+		    (pad_state[i] == TVP5150_PAD_ACTIVE_SVIDEO)) {
+			idx = i;
+			break;
+		}
+	}
+
+	return idx;
+}
+
+static int tvp5150_active_svideo_links(struct tvp5150 *decoder)
+{
+	int *pad_state = &decoder->pads_state[0];
+	int i, links = 0;
+
+	for (i = 0; i < TVP5150_NUM_PADS - 1; i++)
+		if (pad_state[i] == TVP5150_PAD_ACTIVE_SVIDEO)
+			links++;
+
+	return links;
+}
+
+static int tvp5150_modify_link(struct tvp5150 *decoder, unsigned int pad_idx,
+			       struct media_pad *pad, int flags)
+{
+	struct media_pad *src_pad;
+	struct media_link *link;
+
+	if (pad)
+		src_pad = pad;
+	else
+		src_pad = media_entity_remote_pad(&decoder->pads[pad_idx]);
+
+	if (!src_pad)
+		return -1;
+
+	link = media_entity_find_link(src_pad,
+				      &decoder->pads[pad_idx]);
+
+	/*
+	 * Don't use locked version, since we are running already within the
+	 * media_entity_setup_link() context.
+	 */
+	return __media_entity_setup_link(link, flags);
+
+}
+
+static int tvp5150_s_routing(struct v4l2_subdev *sd, u32 input, u32 output,
+			     u32 config);
+
+static int tvp5150_link_setup(struct media_entity *entity,
+			      const struct media_pad *tvp5150_pad,
+			      const struct media_pad *remote, u32 flags)
+{
+	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
+	struct tvp5150 *decoder = to_tvp5150(sd);
+	int *pad_state = &decoder->pads_state[0];
+	int i, active_pad, ret = 0;
+	bool is_svideo = false;
+
+	/*
+	 * The tvp state is determined by the enabled sink pad link.
+	 * Enabling or disabling the source pad link has no effect.
+	 */
+	if (tvp5150_pad->flags & MEDIA_PAD_FL_SOURCE)
+		return 0;
+
+	/* check if the svideo connector should be enabled */
+	for (i = 0; i < decoder->connectors_num; i++) {
+		if (remote->entity == &decoder->connectors[i].ent) {
+			is_svideo = decoder->connectors[i].is_svideo;
+			break;
+		}
+	}
+
+	/* check if there is already a enabled svideo link and determine pad */
+	active_pad = tvp5150_active_pad_idx(decoder);
+
+	dev_dbg(sd->dev, "link setup '%s':%d->'%s':%d[%d]",
+		remote->entity->name, remote->index, tvp5150_pad->entity->name,
+		tvp5150_pad->index, flags & MEDIA_LNK_FL_ENABLED);
+
+	if (flags & MEDIA_LNK_FL_ENABLED) {
+		if (active_pad >= 0 && !decoder->modify_second_link)
+			tvp5150_modify_link(decoder, active_pad, NULL, 0);
+
+		dev_dbg(sd->dev, "Setting %d active [%s]\n", tvp5150_pad->index,
+			is_svideo ? "svideo" : "composite");
+		pad_state[tvp5150_pad->index] =
+			is_svideo ? TVP5150_PAD_ACTIVE_SVIDEO :
+				    TVP5150_PAD_ACTIVE_COMPOSITE;
+
+		if (is_svideo) {
+			if (tvp5150_active_svideo_links(decoder) < 2) {
+				unsigned int idx = tvp5150_pad->index ^ 1;
+
+				decoder->modify_second_link = true;
+				tvp5150_modify_link(decoder, idx,
+						    (struct media_pad *)remote,
+						    MEDIA_LNK_FL_ENABLED);
+			} else {
+				decoder->modify_second_link = false;
+				tvp5150_s_routing(sd, TVP5150_SVIDEO,
+						  TVP5150_NORMAL, 0);
+			}
+		} else {
+			tvp5150_s_routing(sd, tvp5150_pad->index,
+					  TVP5150_NORMAL, 0);
+		}
+	} else {
+		/*
+		 * Svideo streams on two pads and user can request to AIP1A or
+		 * AIP1B pad. In either case both pads gets disabled in in go.
+		 * So check only if user wants to disable a not enabled
+		 * composite pad.
+		 */
+		if (!is_svideo && tvp5150_pad->index != active_pad)
+			goto out;
+
+		dev_dbg(sd->dev, "going inactive\n");
+		pad_state[tvp5150_pad->index] = TVP5150_PAD_INACTIVE;
+
+		/* in case of svideo we need to disable the second pad too */
+		if (tvp5150_active_svideo_links(decoder) > 0) {
+			unsigned int idx = tvp5150_pad->index ^ 1;
+
+			decoder->modify_second_link = true;
+			tvp5150_modify_link(decoder, idx,
+					    (struct media_pad *)remote, 0);
+		}
+
+		if (!decoder->modify_second_link)
+			tvp5150_s_routing(sd, is_svideo ? TVP5150_SVIDEO :
+					  active_pad, TVP5150_BLACK_SCREEN, 0);
+		decoder->modify_second_link = false;
+	}
+out:
+	return ret;
+}
+
+static const struct media_entity_operations tvp5150_sd_media_ops = {
+	.link_setup = tvp5150_link_setup,
+};
+#endif
 /****************************************************************************
 			I2C Command
  ****************************************************************************/
@@ -1315,6 +1492,76 @@ static int tvp5150_g_tuner(struct v4l2_subdev *sd, struct v4l2_tuner *vt)
 	return 0;
 }
 
+static int tvp5150_registered(struct v4l2_subdev *sd)
+{
+#if defined(CONFIG_MEDIA_CONTROLLER)
+	struct tvp5150 *decoder = to_tvp5150(sd);
+	unsigned int i;
+	int ret;
+
+	/*
+	 * Setup connector pads and links. Enable the link to the first
+	 * available connector per default.
+	 */
+	for (i = 0; i < decoder->connectors_num; i++) {
+		struct media_entity *con = &decoder->connectors[i].ent;
+		struct media_pad *pad = &decoder->connectors[i].pad;
+		unsigned int port = decoder->connectors[i].port_num;
+		bool is_svideo = decoder->connectors[i].is_svideo;
+		int flags = i ? 0 : MEDIA_LNK_FL_ENABLED;
+
+		pad->flags = MEDIA_PAD_FL_SOURCE;
+		ret = media_entity_pads_init(con, 1, pad);
+		if (ret < 0)
+			return ret;
+
+		ret = media_device_register_entity(sd->v4l2_dev->mdev, con);
+		if (ret < 0)
+			return ret;
+
+		ret = media_create_pad_link(con, 0, &sd->entity, port, flags);
+		if (ret < 0) {
+			media_device_unregister_entity(con);
+			return ret;
+		}
+
+		if (is_svideo) {
+			/* svideo links to both aip1a and aip1b */
+			ret = media_create_pad_link(con, 0, &sd->entity,
+						    port + 1, flags);
+			if (ret < 0) {
+				media_device_unregister_entity(con);
+				return ret;
+			}
+		}
+
+		/* enable default input */
+		if (flags == MEDIA_LNK_FL_ENABLED) {
+			if (is_svideo) {
+				decoder->pads_state[TVP5150_PAD_AIP1A] =
+				decoder->pads_state[TVP5150_PAD_AIP1B] =
+						TVP5150_PAD_ACTIVE_SVIDEO;
+				decoder->input = TVP5150_SVIDEO;
+			} else {
+				if (port == 0) {
+					decoder->pads_state[TVP5150_PAD_AIP1A] =
+						TVP5150_PAD_ACTIVE_COMPOSITE;
+					decoder->input = TVP5150_COMPOSITE0;
+				} else {
+					decoder->pads_state[TVP5150_PAD_AIP1B] =
+						TVP5150_PAD_ACTIVE_COMPOSITE;
+					decoder->input = TVP5150_COMPOSITE1;
+				}
+			}
+			tvp5150_selmux(sd);
+			decoder->modify_second_link = false;
+		}
+	}
+#endif
+	return 0;
+}
+
+
 /* ----------------------------------------------------------------------- */
 
 static const struct v4l2_ctrl_ops tvp5150_ctrl_ops = {
@@ -1368,6 +1615,10 @@ static const struct v4l2_subdev_ops tvp5150_ops = {
 	.pad = &tvp5150_pad_ops,
 };
 
+static const struct v4l2_subdev_internal_ops tvp5150_internal_ops = {
+	.registered = tvp5150_registered,
+};
+
 /****************************************************************************
 			I2C Client & Driver
  ****************************************************************************/
@@ -1516,38 +1767,197 @@ static int tvp5150_init(struct i2c_client *c)
 	return 0;
 }
 
-static int tvp5150_parse_dt(struct tvp5150 *decoder, struct device_node *np)
+#if defined(CONFIG_MEDIA_CONTROLLER)
+static int tvp5150_add_of_connectors(struct tvp5150 *decoder)
 {
-	struct v4l2_fwnode_endpoint bus_cfg;
-	struct device_node *ep;
-	unsigned int flags;
-	int ret = 0;
+	struct device *dev = decoder->sd.dev;
+	struct device_node *rp;
+	struct of_endpoint ep;
+	struct tvp5150_connector *connectors;
+	unsigned int connectors_num = decoder->connectors_num;
+	int i, ret;
+
+	/* Allocate and initialize all available input connectors */
+	connectors = devm_kcalloc(dev, connectors_num, sizeof(*connectors),
+				  GFP_KERNEL);
+	if (!connectors)
+		return -ENOMEM;
 
-	ep = of_graph_get_next_endpoint(np, NULL);
-	if (!ep)
-		return -EINVAL;
+	for (i = 0; i < connectors_num; i++) {
+		rp = of_graph_get_remote_port_parent(decoder->endpoints[i]);
+		of_graph_parse_endpoint(decoder->endpoints[i], &ep);
+		connectors[i].port_num = ep.port;
+		connectors[i].is_svideo = !!of_device_is_compatible(rp,
+							    "svideo-connector");
 
-	ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &bus_cfg);
-	if (ret)
-		goto err;
+		if (connectors[i].is_svideo)
+			connectors[i].ent.function = MEDIA_ENT_F_CONN_SVIDEO;
+		else
+			connectors[i].ent.function = MEDIA_ENT_F_CONN_COMPOSITE;
+
+		connectors[i].ent.flags = MEDIA_ENT_FL_CONNECTOR;
+		ret = of_property_read_string(rp, "label",
+					      &connectors[i].ent.name);
+		if (ret < 0)
+			return ret;
+	}
+
+	decoder->connectors = connectors;
+
+	return 0;
+}
+#endif
+
+static int tvp5150_mc_init(struct v4l2_subdev *sd)
+{
+#if defined(CONFIG_MEDIA_CONTROLLER)
+	struct tvp5150 *decoder = to_tvp5150(sd);
+	unsigned int i;
+	int ret;
+
+	sd->entity.ops = &tvp5150_sd_media_ops;
+	sd->entity.function = MEDIA_ENT_F_ATV_DECODER;
 
-	flags = bus_cfg.bus.parallel.flags;
+	/* Initialize all TVP5150 pads */
+	for (i = 0; i < TVP5150_NUM_PADS; i++) {
+		if (i < TVP5150_NUM_PADS - 1) {
+			decoder->pads[i].flags = MEDIA_PAD_FL_SINK;
+			decoder->pads[i].sig_type = PAD_SIGNAL_ANALOG;
+		} else {
+			decoder->pads[i].flags = MEDIA_PAD_FL_SOURCE;
+			decoder->pads[i].sig_type = PAD_SIGNAL_DV;
+		}
+	}
+	ret = media_entity_pads_init(&sd->entity, TVP5150_NUM_PADS,
+				     decoder->pads);
+	if (ret < 0)
+		goto out;
 
-	if (bus_cfg.bus_type == V4L2_MBUS_PARALLEL &&
-	    !(flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH &&
-	      flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH &&
-	      flags & V4L2_MBUS_FIELD_EVEN_LOW)) {
+	if (IS_ENABLED(CONFIG_OF))
+		ret = tvp5150_add_of_connectors(decoder);
+#endif
+out:
+	return ret;
+}
+
+static bool tvp5150_of_valid_input(struct device_node *endpoint,
+				unsigned int port, unsigned int id)
+{
+	struct device_node *rp = of_graph_get_remote_port_parent(endpoint);
+	const char *input;
+	int ret;
+
+	/* perform some basic checks needed for later mc_init */
+	switch (port) {
+	case TVP5150_PAD_AIP1A:
+		/* svideo must be connected to endpoint@1  */
+		ret = id ? of_device_is_compatible(rp, "svideo-connector") :
+			   of_device_is_compatible(rp,
+						   "composite-video-connector");
+		if (!ret)
+			return false;
+		break;
+	case TVP5150_PAD_AIP1B:
+		ret = of_device_is_compatible(rp, "composite-video-connector");
+		if (!ret)
+			return false;
+		break;
+	}
+
+	ret = of_property_read_string(rp, "label", &input);
+	if (ret < 0)
+		return false;
+
+	return true;
+}
+
+static int tvp5150_parse_dt(struct tvp5150 *decoder, struct device_node *np)
+{
+	struct device *dev = decoder->sd.dev;
+	struct v4l2_fwnode_endpoint bus_cfg;
+	struct device_node *ep_np;
+	unsigned int flags;
+	int ret, i = 0, in = 0;
+	bool found = false;
+
+	/* at least 1 output and 1 input */
+	decoder->endpoints_num = of_graph_get_endpoint_count(np);
+	if (decoder->endpoints_num < 2 || decoder->endpoints_num > 4) {
 		ret = -EINVAL;
 		goto err;
 	}
 
-	decoder->mbus_type = bus_cfg.bus_type;
+	for_each_endpoint_of_node(np, ep_np) {
+		struct of_endpoint ep;
+
+		of_graph_parse_endpoint(ep_np, &ep);
+		if (decoder->endpoints[i]) {
+			/* this should never happen */
+			dev_err(dev, "Invalid endpoint %pOF on port %d\n",
+				ep.local_node, ep.port);
+				ret = -EINVAL;
+				goto err;
+		}
 
+		switch (ep.port) {
+			/* fall through */
+		case TVP5150_PAD_AIP1A:
+		case TVP5150_PAD_AIP1B:
+			if (!tvp5150_of_valid_input(ep_np, ep.port, ep.id)) {
+				dev_err(dev,
+					"Invalid endpoint %pOF on port %d\n",
+					ep.local_node, ep.port);
+				ret = -EINVAL;
+				goto err;
+			}
+			in++;
+			break;
+		case TVP5150_PAD_VID_OUT:
+			ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_np),
+							 &bus_cfg);
+			if (ret)
+				goto err;
+
+			flags = bus_cfg.bus.parallel.flags;
+
+			if (bus_cfg.bus_type == V4L2_MBUS_PARALLEL &&
+			    !(flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH &&
+			      flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH &&
+			      flags & V4L2_MBUS_FIELD_EVEN_LOW)) {
+				ret = -EINVAL;
+				goto err;
+			}
+
+			decoder->mbus_type = bus_cfg.bus_type;
+			break;
+		default:
+			dev_err(dev, "Invalid port %d for endpoint %pOF\n",
+				ep.port, ep.local_node);
+			ret = -EINVAL;
+			goto err;
+		}
+
+		of_node_get(ep_np);
+		decoder->endpoints[i] = ep_np;
+		i++;
+
+		found = true;
+	}
+
+	decoder->connectors_num = in;
+	return found ? 0 : -ENODEV;
 err:
-	of_node_put(ep);
 	return ret;
 }
 
+static void tvp5150_dt_cleanup(struct tvp5150 *decoder)
+{
+	unsigned int i;
+
+	for (i = 0; i < TVP5150_NUM_PADS; i++)
+		of_node_put(decoder->endpoints[i]);
+}
+
 static const char * const tvp5150_test_patterns[2] = {
 	"Disabled",
 	"Black screen"
@@ -1586,7 +1996,7 @@ static int tvp5150_probe(struct i2c_client *c,
 		res = tvp5150_parse_dt(core, np);
 		if (res) {
 			dev_err(sd->dev, "DT parsing error: %d\n", res);
-			return res;
+			goto err_cleanup_dt;
 		}
 	} else {
 		/* Default to BT.656 embedded sync */
@@ -1594,25 +2004,16 @@ static int tvp5150_probe(struct i2c_client *c,
 	}
 
 	v4l2_i2c_subdev_init(sd, c, &tvp5150_ops);
+	sd->internal_ops = &tvp5150_internal_ops;
 	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
 
-#if defined(CONFIG_MEDIA_CONTROLLER)
-	core->pads[TVP5150_PAD_IF_INPUT].flags = MEDIA_PAD_FL_SINK;
-	core->pads[TVP5150_PAD_IF_INPUT].sig_type = PAD_SIGNAL_ANALOG;
-	core->pads[TVP5150_PAD_VID_OUT].flags = MEDIA_PAD_FL_SOURCE;
-	core->pads[TVP5150_PAD_VID_OUT].sig_type = PAD_SIGNAL_DV;
-
-	sd->entity.function = MEDIA_ENT_F_ATV_DECODER;
-
-	res = media_entity_pads_init(&sd->entity, TVP5150_NUM_PADS, core->pads);
-	if (res < 0)
-		return res;
-
-#endif
+	res = tvp5150_mc_init(sd);
+	if (res)
+		goto err_cleanup_dt;
 
 	res = tvp5150_detect_version(core);
 	if (res < 0)
-		return res;
+		goto err_cleanup_dt;
 
 	core->norm = V4L2_STD_ALL;	/* Default is autodetect */
 	core->detected_norm = V4L2_STD_UNKNOWN;
@@ -1638,7 +2039,7 @@ static int tvp5150_probe(struct i2c_client *c,
 	sd->ctrl_handler = &core->hdl;
 	if (core->hdl.error) {
 		res = core->hdl.error;
-		goto err;
+		goto err_free_v4l2_ctrls;
 	}
 
 	tvp5150_set_default(tvp5150_read_std(sd), &core->rect);
@@ -1650,19 +2051,21 @@ static int tvp5150_probe(struct i2c_client *c,
 						tvp5150_isr, IRQF_TRIGGER_HIGH |
 						IRQF_ONESHOT, "tvp5150", core);
 		if (res)
-			goto err;
+			goto err_free_v4l2_ctrls;
 	}
 
 	res = v4l2_async_register_subdev(sd);
 	if (res < 0)
-		goto err;
+		goto err_free_v4l2_ctrls;
 
 	if (debug > 1)
 		tvp5150_log_status(sd);
 	return 0;
 
-err:
+err_free_v4l2_ctrls:
 	v4l2_ctrl_handler_free(&core->hdl);
+err_cleanup_dt:
+	tvp5150_dt_cleanup(core);
 	return res;
 }
 
-- 
2.19.0

[PATCH v3 4/9] media: dt-bindings: tvp5150: Add input port connectors DT bindings

[Marco Felsch]

The TVP5150/1 decoders support different video input sources to their
AIP1A/B pins.

Possible configurations are as follows:
  - Analog Composite signal connected to AIP1A.
  - Analog Composite signal connected to AIP1B.
  - Analog S-Video Y (luminance) and C (chrominance)
    signals connected to AIP1A and AIP1B respectively.

This patch extends the device tree bindings documentation to describe
how the input connectors for these devices should be defined in a DT.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
Changelog:

v3:
- remove examples for one and two inputs
- replace space by tabs

v2:
- adapt port layout in accordance with
  https://www.spinics.net/lists/linux-media/msg138546.html with the
  svideo-connector deviation (use only one endpoint)

 .../devicetree/bindings/media/i2c/tvp5150.txt | 92 +++++++++++++++++--
 1 file changed, 85 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
index 8c0fc1a26bf0..bdd273d8b44d 100644
--- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
+++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
@@ -12,11 +12,31 @@ Optional Properties:
 - pdn-gpios: phandle for the GPIO connected to the PDN pin, if any.
 - reset-gpios: phandle for the GPIO connected to the RESETB pin, if any.
 
-The device node must contain one 'port' child node for its digital output
-video port, in accordance with the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt.
+The device node must contain one 'port' child node per device physical input
+and output port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows
 
-Required Endpoint Properties for parallel synchronization:
+	  Name		Type		Port
+	--------------------------------------
+	  AIP1A		sink		0
+	  AIP1B		sink		1
+	  Y-OUT		src		2
+
+The device node must contain at least one sink port and the src port. Each input
+port must be linked to an endpoint defined in
+Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt. The
+port/connector layout is as follows
+
+tvp-5150 port@0 (AIP1A)
+	endpoint@0 -----------> Comp0-Con  port
+	endpoint@1 -----------> Svideo-Con port
+tvp-5150 port@1 (AIP1B)
+	endpoint   -----------> Comp1-Con  port
+tvp-5150 port@2
+	endpoint (video bitstream output at YOUT[0-7] parallel bus)
+
+Required Endpoint Properties for parallel synchronization on output port:
 
 - hsync-active: active state of the HSYNC signal. Must be <1> (HIGH).
 - vsync-active: active state of the VSYNC signal. Must be <1> (HIGH).
@@ -26,17 +46,75 @@ Required Endpoint Properties for parallel synchronization:
 If none of hsync-active, vsync-active and field-even-active is specified,
 the endpoint is assumed to use embedded BT.656 synchronization.
 
-Example:
+Example - three input sources:
+
+comp_connector_0 {
+	compatible = "composite-video-connector";
+	label = "Composite0";
+
+	port {
+		composite0_to_tvp5150: endpoint {
+			remote-endpoint = <&tvp5150_to_composite0>;
+		};
+	};
+};
+
+comp_connector_1 {
+	compatible = "composite-video-connector";
+	label = "Composite1";
+
+	port {
+		composite1_to_tvp5150: endpoint {
+			remote-endpoint = <&tvp5150_to_composite1>;
+		};
+	};
+};
+
+svid_connector {
+	compatible = "svideo-connector";
+	label = "S-Video";
+
+	port {
+		svideo_to_tvp5150: endpoint {
+			remote-endpoint = <&tvp5150_to_svideo>;
+		};
+	};
+};
 
 &i2c2 {
-	...
 	tvp5150@5c {
 		compatible = "ti,tvp5150";
 		reg = <0x5c>;
 		pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
 		reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
 
-		port {
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			tvp5150_to_composite0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&composite0_to_tvp5150>;
+			};
+
+			tvp5150_to_svideo: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&svideo_to_tvp5150>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			tvp5150_to_composite1: endpoint {
+                                remote-endpoint = <&composite1_to_tvp5150>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
 			tvp5150_1: endpoint {
 				remote-endpoint = <&ccdc_ep>;
 			};
-- 
2.19.0

[PATCH v3 5/9] media: v4l2-subdev: add stubs for v4l2_subdev_get_try_*

[Marco Felsch]

In case of missing CONFIG_VIDEO_V4L2_SUBDEV_API those helpers aren't
available. So each driver have to add ifdefs around those helpers or
add the CONFIG_VIDEO_V4L2_SUBDEV_API as dependcy.

Make these helpers available in case of CONFIG_VIDEO_V4L2_SUBDEV_API
isn't set to avoid ifdefs. This approach is less error prone too.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
 include/media/v4l2-subdev.h | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index 9102d6ca566e..ce48f1fcf295 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -912,8 +912,6 @@ struct v4l2_subdev_fh {
 #define to_v4l2_subdev_fh(fh)	\
 	container_of(fh, struct v4l2_subdev_fh, vfh)
 
-#if defined(CONFIG_VIDEO_V4L2_SUBDEV_API)
-
 /**
  * v4l2_subdev_get_try_format - ancillary routine to call
  *	&struct v4l2_subdev_pad_config->try_fmt
@@ -927,9 +925,13 @@ static inline struct v4l2_mbus_framefmt
 			    struct v4l2_subdev_pad_config *cfg,
 			    unsigned int pad)
 {
+#if defined(CONFIG_VIDEO_V4L2_SUBDEV_API)
 	if (WARN_ON(pad >= sd->entity.num_pads))
 		pad = 0;
 	return &cfg[pad].try_fmt;
+#else
+	return NULL;
+#endif
 }
 
 /**
@@ -945,9 +947,13 @@ static inline struct v4l2_rect
 			  struct v4l2_subdev_pad_config *cfg,
 			  unsigned int pad)
 {
+#if defined(CONFIG_VIDEO_V4L2_SUBDEV_API)
 	if (WARN_ON(pad >= sd->entity.num_pads))
 		pad = 0;
 	return &cfg[pad].try_crop;
+#else
+	return NULL;
+#endif
 }
 
 /**
@@ -963,11 +969,14 @@ static inline struct v4l2_rect
 			     struct v4l2_subdev_pad_config *cfg,
 			     unsigned int pad)
 {
+#if defined(CONFIG_VIDEO_V4L2_SUBDEV_API)
 	if (WARN_ON(pad >= sd->entity.num_pads))
 		pad = 0;
 	return &cfg[pad].try_compose;
-}
+#else
+	return NULL;
 #endif
+}
 
 extern const struct v4l2_file_operations v4l2_subdev_fops;
 
-- 
2.19.0

[PATCH v3 6/9] media: v4l2-subdev: fix v4l2_subdev_get_try_* dependency

[Marco Felsch]

These helpers make us of the media-controller entity which is only
available if the CONFIG_MEDIA_CONTROLLER is enabled.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
Changelog:

v3:
- add CONFIG_MEDIA_CONTROLLER switch instead of moving the
  v4l2_subdev_get_try_* APIs into the existing one.

v2:
- Initial commit

 include/media/v4l2-subdev.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index ce48f1fcf295..d2479d5ebca8 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -912,6 +912,8 @@ struct v4l2_subdev_fh {
 #define to_v4l2_subdev_fh(fh)	\
 	container_of(fh, struct v4l2_subdev_fh, vfh)
 
+#ifdef CONFIG_MEDIA_CONTROLLER
+
 /**
  * v4l2_subdev_get_try_format - ancillary routine to call
  *	&struct v4l2_subdev_pad_config->try_fmt
@@ -978,6 +980,8 @@ static inline struct v4l2_rect
 #endif
 }
 
+#endif
+
 extern const struct v4l2_file_operations v4l2_subdev_fops;
 
 /**
-- 
2.19.0

[PATCH v3 7/9] media: tvp5150: add FORMAT_TRY support for get/set selection handlers

[Marco Felsch]

Since commit 10d5509c8d50 ("[media] v4l2: remove g/s_crop from video ops")
the 'which' field for set/get_selection must be FORMAT_ACTIVE. There is
no way to try different selections. The patch adds a helper function to
select the correct selection memory space (sub-device file handle or
driver state) which will be set/returned.

The TVP5150 AVID will be updated if the 'which' field is FORMAT_ACTIVE
and the requested selection rectangle differs from the already set one.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
 drivers/media/i2c/tvp5150.c | 109 +++++++++++++++++++++++++-----------
 1 file changed, 75 insertions(+), 34 deletions(-)

diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
index 40ecbce03e2c..b34d0e883c06 100644
--- a/drivers/media/i2c/tvp5150.c
+++ b/drivers/media/i2c/tvp5150.c
@@ -19,6 +19,7 @@
 #include <media/v4l2-ctrls.h>
 #include <media/v4l2-fwnode.h>
 #include <media/v4l2-mc.h>
+#include <media/v4l2-rect.h>
 
 #include "tvp5150_reg.h"
 
@@ -1007,20 +1008,40 @@ static void tvp5150_set_default(v4l2_std_id std, struct v4l2_rect *crop)
 		crop->height = TVP5150_V_MAX_OTHERS;
 }
 
+static struct v4l2_rect *
+__tvp5150_get_pad_crop(struct tvp5150 *decoder,
+		       struct v4l2_subdev_pad_config *cfg, unsigned int pad,
+		       enum v4l2_subdev_format_whence which)
+{
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		return v4l2_subdev_get_try_crop(&decoder->sd, cfg, pad);
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		return &decoder->rect;
+	default:
+		return NULL;
+	}
+}
+
 static int tvp5150_fill_fmt(struct v4l2_subdev *sd,
 			    struct v4l2_subdev_pad_config *cfg,
 			    struct v4l2_subdev_format *format)
 {
 	struct v4l2_mbus_framefmt *f;
+	struct v4l2_rect *__crop;
 	struct tvp5150 *decoder = to_tvp5150(sd);
 
 	if (!format || (format->pad != TVP5150_PAD_VID_OUT))
 		return -EINVAL;
 
 	f = &format->format;
+	__crop = __tvp5150_get_pad_crop(decoder, cfg, format->pad,
+					format->which);
+	if (!__crop)
+		return -EINVAL;
 
-	f->width = decoder->rect.width;
-	f->height = decoder->rect.height / 2;
+	f->width = __crop->width;
+	f->height = __crop->height / 2;
 
 	f->code = TVP5150_MBUS_FMT;
 	f->field = TVP5150_FIELD;
@@ -1031,17 +1052,51 @@ static int tvp5150_fill_fmt(struct v4l2_subdev *sd,
 	return 0;
 }
 
+unsigned int tvp5150_get_hmax(struct v4l2_subdev *sd)
+{
+	struct tvp5150 *decoder = to_tvp5150(sd);
+	v4l2_std_id std;
+
+	/* Calculate height based on current standard */
+	if (decoder->norm == V4L2_STD_ALL)
+		std = tvp5150_read_std(sd);
+	else
+		std = decoder->norm;
+
+	return (std & V4L2_STD_525_60) ?
+		TVP5150_V_MAX_525_60 : TVP5150_V_MAX_OTHERS;
+}
+
+static inline void
+__tvp5150_set_selection(struct v4l2_subdev *sd, struct v4l2_rect rect)
+{
+	struct tvp5150 *decoder = to_tvp5150(sd);
+	unsigned int hmax = tvp5150_get_hmax(sd);
+
+	regmap_write(decoder->regmap, TVP5150_VERT_BLANKING_START, rect.top);
+	regmap_write(decoder->regmap, TVP5150_VERT_BLANKING_STOP,
+		     rect.top + rect.height - hmax);
+	regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_ST_MSB,
+		     rect.left >> TVP5150_CROP_SHIFT);
+	regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_ST_LSB,
+		     rect.left | (1 << TVP5150_CROP_SHIFT));
+	regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_STP_MSB,
+		     (rect.left + rect.width - TVP5150_MAX_CROP_LEFT) >>
+		     TVP5150_CROP_SHIFT);
+	regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_STP_LSB,
+		     rect.left + rect.width - TVP5150_MAX_CROP_LEFT);
+}
+
 static int tvp5150_set_selection(struct v4l2_subdev *sd,
 				 struct v4l2_subdev_pad_config *cfg,
 				 struct v4l2_subdev_selection *sel)
 {
 	struct tvp5150 *decoder = to_tvp5150(sd);
 	struct v4l2_rect rect = sel->r;
-	v4l2_std_id std;
-	int hmax;
+	struct v4l2_rect *__crop;
+	unsigned int hmax;
 
-	if (sel->which != V4L2_SUBDEV_FORMAT_ACTIVE ||
-	    sel->target != V4L2_SEL_TGT_CROP)
+	if (sel->target != V4L2_SEL_TGT_CROP)
 		return -EINVAL;
 
 	dev_dbg_lvl(sd->dev, 1, debug, "%s left=%d, top=%d, width=%d, height=%d\n",
@@ -1050,17 +1105,7 @@ static int tvp5150_set_selection(struct v4l2_subdev *sd,
 	/* tvp5150 has some special limits */
 	rect.left = clamp(rect.left, 0, TVP5150_MAX_CROP_LEFT);
 	rect.top = clamp(rect.top, 0, TVP5150_MAX_CROP_TOP);
-
-	/* Calculate height based on current standard */
-	if (decoder->norm == V4L2_STD_ALL)
-		std = tvp5150_read_std(sd);
-	else
-		std = decoder->norm;
-
-	if (std & V4L2_STD_525_60)
-		hmax = TVP5150_V_MAX_525_60;
-	else
-		hmax = TVP5150_V_MAX_OTHERS;
+	hmax = tvp5150_get_hmax(sd);
 
 	/*
 	 * alignments:
@@ -1073,20 +1118,18 @@ static int tvp5150_set_selection(struct v4l2_subdev *sd,
 			      hmax - TVP5150_MAX_CROP_TOP - rect.top,
 			      hmax - rect.top, 0, 0);
 
-	regmap_write(decoder->regmap, TVP5150_VERT_BLANKING_START, rect.top);
-	regmap_write(decoder->regmap, TVP5150_VERT_BLANKING_STOP,
-		      rect.top + rect.height - hmax);
-	regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_ST_MSB,
-		      rect.left >> TVP5150_CROP_SHIFT);
-	regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_ST_LSB,
-		      rect.left | (1 << TVP5150_CROP_SHIFT));
-	regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_STP_MSB,
-		      (rect.left + rect.width - TVP5150_MAX_CROP_LEFT) >>
-		      TVP5150_CROP_SHIFT);
-	regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_STP_LSB,
-		      rect.left + rect.width - TVP5150_MAX_CROP_LEFT);
+	__crop = __tvp5150_get_pad_crop(decoder, cfg, sel->pad,
+						  sel->which);
+
+	/*
+	 * Update output image size if the selection (crop) rectangle size or
+	 * position has been modified.
+	 */
+	if (!v4l2_rect_equal(&rect, __crop))
+		if (sel->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+			__tvp5150_set_selection(sd, rect);
 
-	decoder->rect = rect;
+	*__crop = rect;
 
 	return 0;
 }
@@ -1098,9 +1141,6 @@ static int tvp5150_get_selection(struct v4l2_subdev *sd,
 	struct tvp5150 *decoder = container_of(sd, struct tvp5150, sd);
 	v4l2_std_id std;
 
-	if (sel->which != V4L2_SUBDEV_FORMAT_ACTIVE)
-		return -EINVAL;
-
 	switch (sel->target) {
 	case V4L2_SEL_TGT_CROP_BOUNDS:
 	case V4L2_SEL_TGT_CROP_DEFAULT:
@@ -1119,7 +1159,8 @@ static int tvp5150_get_selection(struct v4l2_subdev *sd,
 			sel->r.height = TVP5150_V_MAX_OTHERS;
 		return 0;
 	case V4L2_SEL_TGT_CROP:
-		sel->r = decoder->rect;
+		sel->r = *__tvp5150_get_pad_crop(decoder, cfg, sel->pad,
+						      sel->which);
 		return 0;
 	default:
 		return -EINVAL;
-- 
2.19.0

[PATCH v3 8/9] media: tvp5150: initialize subdev before parsing device tree

[Marco Felsch]

From: Michael Tretter <m.tretter@pengutronix.de>

There are several debug prints in the tvp5150_parse_dt() function, which
do not print the prefix, because the v4l2_subdev is not initialized, yet.

Initialize the v4l2_subdev before parsing the device tree to fix the
debug messages.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
 drivers/media/i2c/tvp5150.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
index b34d0e883c06..535e97c7b266 100644
--- a/drivers/media/i2c/tvp5150.c
+++ b/drivers/media/i2c/tvp5150.c
@@ -2032,6 +2032,9 @@ static int tvp5150_probe(struct i2c_client *c,
 
 	core->regmap = map;
 	sd = &core->sd;
+	v4l2_i2c_subdev_init(sd, c, &tvp5150_ops);
+	sd->internal_ops = &tvp5150_internal_ops;
+	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
 
 	if (IS_ENABLED(CONFIG_OF) && np) {
 		res = tvp5150_parse_dt(core, np);
@@ -2044,10 +2047,6 @@ static int tvp5150_probe(struct i2c_client *c,
 		core->mbus_type = V4L2_MBUS_BT656;
 	}
 
-	v4l2_i2c_subdev_init(sd, c, &tvp5150_ops);
-	sd->internal_ops = &tvp5150_internal_ops;
-	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
-
 	res = tvp5150_mc_init(sd);
 	if (res)
 		goto err_cleanup_dt;
-- 
2.19.0

[PATCH v3 9/9] media: tvp5150: add s_power callback

[Marco Felsch]

Don't en-/disable the interrupts during s_stream because someone can
disable the stream but wants to get informed if the stream is locked
again. So keep the interrupts enabled the whole time the pipeline is
opened.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
 drivers/media/i2c/tvp5150.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)

diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
index 535e97c7b266..40536f8ffcae 100644
--- a/drivers/media/i2c/tvp5150.c
+++ b/drivers/media/i2c/tvp5150.c
@@ -1389,11 +1389,26 @@ static const struct media_entity_operations tvp5150_sd_media_ops = {
 /****************************************************************************
 			I2C Command
  ****************************************************************************/
+static int tvp5150_s_power(struct  v4l2_subdev *sd, int on)
+{
+	struct tvp5150 *decoder = to_tvp5150(sd);
+	unsigned int val = 0;
+
+	if (on)
+		val = TVP5150_INT_A_LOCK;
+
+	if (decoder->irq)
+		/* Enable / Disable lock interrupt */
+		regmap_update_bits(decoder->regmap, TVP5150_INT_ENABLE_REG_A,
+				   TVP5150_INT_A_LOCK, val);
+
+	return 0;
+}
 
 static int tvp5150_s_stream(struct v4l2_subdev *sd, int enable)
 {
 	struct tvp5150 *decoder = to_tvp5150(sd);
-	unsigned int mask, val = 0, int_val = 0;
+	unsigned int mask, val = 0;
 
 	mask = TVP5150_MISC_CTL_YCBCR_OE | TVP5150_MISC_CTL_SYNC_OE |
 	       TVP5150_MISC_CTL_CLOCK_OE;
@@ -1406,15 +1421,10 @@ static int tvp5150_s_stream(struct v4l2_subdev *sd, int enable)
 			val = decoder->lock ? decoder->oe : 0;
 		else
 			val = decoder->oe;
-		int_val = TVP5150_INT_A_LOCK;
 		v4l2_subdev_notify_event(&decoder->sd, &tvp5150_ev_fmt);
 	}
 
 	regmap_update_bits(decoder->regmap, TVP5150_MISC_CTL, mask, val);
-	if (decoder->irq)
-		/* Enable / Disable lock interrupt */
-		regmap_update_bits(decoder->regmap, TVP5150_INT_ENABLE_REG_A,
-				   TVP5150_INT_A_LOCK, int_val);
 
 	return 0;
 }
@@ -1616,6 +1626,7 @@ static const struct v4l2_subdev_core_ops tvp5150_core_ops = {
 	.g_register = tvp5150_g_register,
 	.s_register = tvp5150_s_register,
 #endif
+	.s_power = tvp5150_s_power,
 };
 
 static const struct v4l2_subdev_tuner_ops tvp5150_tuner_ops = {
-- 
2.19.0

Re: [PATCH v3 6/9] media: v4l2-subdev: fix v4l2_subdev_get_try_* dependency

[Sakari Ailus]

Hi Marco,

On Tue, Sep 18, 2018 at 03:14:50PM +0200, Marco Felsch wrote:
> These helpers make us of the media-controller entity which is only
> available if the CONFIG_MEDIA_CONTROLLER is enabled.
> 
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> ---
> Changelog:
> 
> v3:
> - add CONFIG_MEDIA_CONTROLLER switch instead of moving the
>   v4l2_subdev_get_try_* APIs into the existing one.
> 
> v2:
> - Initial commit
> 
>  include/media/v4l2-subdev.h | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
> index ce48f1fcf295..d2479d5ebca8 100644
> --- a/include/media/v4l2-subdev.h
> +++ b/include/media/v4l2-subdev.h
> @@ -912,6 +912,8 @@ struct v4l2_subdev_fh {
>  #define to_v4l2_subdev_fh(fh)	\
>  	container_of(fh, struct v4l2_subdev_fh, vfh)
>  
> +#ifdef CONFIG_MEDIA_CONTROLLER

VIDEO_V4L2_SUBDEV_API (used below) depends on MEDIA_CONTROLLER. Either this
or the previous patch would be meaningful but not both.

Considering a driver wouldn't use the functions below if it did not need or
could use VIDEO_V4L2_SUBDEV_API, I'd suggest retaining the other patch.

> +
>  /**
>   * v4l2_subdev_get_try_format - ancillary routine to call
>   *	&struct v4l2_subdev_pad_config->try_fmt
> @@ -978,6 +980,8 @@ static inline struct v4l2_rect
>  #endif
>  }
>  
> +#endif
> +
>  extern const struct v4l2_file_operations v4l2_subdev_fops;
>  
>  /**

-- 
Sakari Ailus
e-mail: sakari.ailus@iki.fi

Re: [PATCH v3 6/9] media: v4l2-subdev: fix v4l2_subdev_get_try_* dependency

[Marco Felsch]

Hi Sakari,

On 18-09-19 13:45, Sakari Ailus wrote:
> Hi Marco,
> 
> On Tue, Sep 18, 2018 at 03:14:50PM +0200, Marco Felsch wrote:
> > These helpers make us of the media-controller entity which is only
> > available if the CONFIG_MEDIA_CONTROLLER is enabled.
> > 
> > Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> > ---
> > Changelog:
> > 
> > v3:
> > - add CONFIG_MEDIA_CONTROLLER switch instead of moving the
> >   v4l2_subdev_get_try_* APIs into the existing one.
> > 
> > v2:
> > - Initial commit
> > 
> >  include/media/v4l2-subdev.h | 4 ++++
> >  1 file changed, 4 insertions(+)
> > 
> > diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
> > index ce48f1fcf295..d2479d5ebca8 100644
> > --- a/include/media/v4l2-subdev.h
> > +++ b/include/media/v4l2-subdev.h
> > @@ -912,6 +912,8 @@ struct v4l2_subdev_fh {
> >  #define to_v4l2_subdev_fh(fh)	\
> >  	container_of(fh, struct v4l2_subdev_fh, vfh)
> >  
> > +#ifdef CONFIG_MEDIA_CONTROLLER
> 
> VIDEO_V4L2_SUBDEV_API (used below) depends on MEDIA_CONTROLLER. Either this
> or the previous patch would be meaningful but not both.
> 
> Considering a driver wouldn't use the functions below if it did not need or
> could use VIDEO_V4L2_SUBDEV_API, I'd suggest retaining the other patch.

Oh sorry didn't checked the Kconfig.
Mauro can you drop that patch and use only the patch ("media: v4l2-subdev:
add stubs for v4l2_subdev_get_try_*")?

Regards,
Marco

> > +
> >  /**
> >   * v4l2_subdev_get_try_format - ancillary routine to call
> >   *	&struct v4l2_subdev_pad_config->try_fmt
> > @@ -978,6 +980,8 @@ static inline struct v4l2_rect
> >  #endif
> >  }
> >  
> > +#endif
> > +
> >  extern const struct v4l2_file_operations v4l2_subdev_fops;
> >  
> >  /**
> 
> -- 
> Sakari Ailus
> e-mail: sakari.ailus@iki.fi
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

Re: [PATCH v3 1/9] partial revert of "[media] tvp5150: add HW input connectors support"

[Rob Herring]

On Tue, Sep 18, 2018 at 03:14:45PM +0200, Marco Felsch wrote:
> From: Javier Martinez Canillas <javierm@redhat.com>
> 
> Commit f7b4b54e6364 ("[media] tvp5150: add HW input connectors support")
> added input signals support for the tvp5150, but the approach was found
> to be incorrect so the corresponding DT binding commit 82c2ffeb217a
> ("[media] tvp5150: document input connectors DT bindings") was reverted.
> 
> This left the driver with an undocumented (and wrong) DT parsing logic,
> so lets get rid of this code as well until the input connectors support
> is implemented properly.
> 
> It's a partial revert due other patches added on top of mentioned commit
> not allowing the commit to be reverted cleanly anymore. But all the code
> related to the DT parsing logic and input entities creation are removed.
> 
> Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> [m.felsch@pengutronix.de: rm TVP5150_INPUT_NUM define]
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
> ---
>  drivers/media/i2c/tvp5150.c         | 141 ----------------------------
>  include/dt-bindings/media/tvp5150.h |   2 -
>  2 files changed, 143 deletions(-)

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 4/9] media: dt-bindings: tvp5150: Add input port connectors DT bindings

[Rob Herring]

On Tue, 18 Sep 2018 15:14:48 +0200, Marco Felsch wrote:
> The TVP5150/1 decoders support different video input sources to their
> AIP1A/B pins.
> 
> Possible configurations are as follows:
>   - Analog Composite signal connected to AIP1A.
>   - Analog Composite signal connected to AIP1B.
>   - Analog S-Video Y (luminance) and C (chrominance)
>     signals connected to AIP1A and AIP1B respectively.
> 
> This patch extends the device tree bindings documentation to describe
> how the input connectors for these devices should be defined in a DT.
> 
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> ---
> Changelog:
> 
> v3:
> - remove examples for one and two inputs
> - replace space by tabs
> 
> v2:
> - adapt port layout in accordance with
>   https://www.spinics.net/lists/linux-media/msg138546.html with the
>   svideo-connector deviation (use only one endpoint)
> 
>  .../devicetree/bindings/media/i2c/tvp5150.txt | 92 +++++++++++++++++--
>  1 file changed, 85 insertions(+), 7 deletions(-)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 0/9] TVP5150 fixes and new features

[Marco Felsch]

Hi Mauro,

just a reminder, Rob already added his ack/rev-by tags.

Thanks,
Marco

On 18-09-18 15:14, Marco Felsch wrote:
> Hi,
> 
> this is my v3 with the integrated reviews from my v2 [1]. This serie
> applies to Mauro's experimental.git [2].
> 
> @Mauro:
> Patch ("media: tvp5150: fix irq_request error path during probe") is new
> in this series. Maybe you can squash them with ("media: tvp5150: Add sync lock
> interrupt handling"), thanks.
> 
> I've tested this series on a customer dt-based board. Unfortunately I
> haven't a device which use the em28xx driver. So other tester a welcome :)
> 
> [1] https://www.spinics.net/lists/devicetree/msg244129.html
> [2] https://git.linuxtv.org/mchehab/experimental.git/log/?h=tvp5150-4
> 
> Javier Martinez Canillas (1):
>   partial revert of "[media] tvp5150: add HW input connectors support"
> 
> Marco Felsch (7):
>   media: tvp5150: fix irq_request error path during probe
>   media: tvp5150: add input source selection of_graph support
>   media: dt-bindings: tvp5150: Add input port connectors DT bindings
>   media: v4l2-subdev: add stubs for v4l2_subdev_get_try_*
>   media: v4l2-subdev: fix v4l2_subdev_get_try_* dependency
>   media: tvp5150: add FORMAT_TRY support for get/set selection handlers
>   media: tvp5150: add s_power callback
> 
> Michael Tretter (1):
>   media: tvp5150: initialize subdev before parsing device tree
> 
>  .../devicetree/bindings/media/i2c/tvp5150.txt |  92 ++-
>  drivers/media/i2c/tvp5150.c                   | 657 +++++++++++++-----
>  include/dt-bindings/media/tvp5150.h           |   2 -
>  include/media/v4l2-subdev.h                   |  15 +-
>  4 files changed, 584 insertions(+), 182 deletions(-)
> 
> -- 
> 2.19.0
> 
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

Re: [PATCH v3 2/9] media: tvp5150: fix irq_request error path during probe

[Laurent Pinchart]

Hi Marco,

Thank you for the patch.

On Tuesday, 18 September 2018 16:14:46 EEST Marco Felsch wrote:
> Commit 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")
> introduced the interrupt handling. But we have to free the
> v4l2_ctrl_handler before we can return the error code.
> 
> Fixes: 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>  drivers/media/i2c/tvp5150.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
> index 133073518744..40aaa8ca0b63 100644
> --- a/drivers/media/i2c/tvp5150.c
> +++ b/drivers/media/i2c/tvp5150.c
> @@ -1650,7 +1650,7 @@ static int tvp5150_probe(struct i2c_client *c,
>  						tvp5150_isr, IRQF_TRIGGER_HIGH |
>  						IRQF_ONESHOT, "tvp5150", core);
>  		if (res)
> -			return res;
> +			goto err;
>  	}
> 
>  	res = v4l2_async_register_subdev(sd);

-- 
Regards,

Laurent Pinchart

Re: [PATCH v3 0/9] TVP5150 fixes and new features

[Marco Felsch]

Hi Mauro,

I don't want to spam you. Can you give me some feedback? I know the
merge window is a busy time, so maybe you have some time now.

Regards,
Marco

On 18-10-29 19:41, Marco Felsch wrote:
> Hi Mauro,
> 
> just a reminder, Rob already added his ack/rev-by tags.
> 
> Thanks,
> Marco
> 
> On 18-09-18 15:14, Marco Felsch wrote:
> > Hi,
> > 
> > this is my v3 with the integrated reviews from my v2 [1]. This serie
> > applies to Mauro's experimental.git [2].
> > 
> > @Mauro:
> > Patch ("media: tvp5150: fix irq_request error path during probe") is new
> > in this series. Maybe you can squash them with ("media: tvp5150: Add sync lock
> > interrupt handling"), thanks.
> > 
> > I've tested this series on a customer dt-based board. Unfortunately I
> > haven't a device which use the em28xx driver. So other tester a welcome :)
> > 
> > [1] https://www.spinics.net/lists/devicetree/msg244129.html
> > [2] https://git.linuxtv.org/mchehab/experimental.git/log/?h=tvp5150-4
> > 
> > Javier Martinez Canillas (1):
> >   partial revert of "[media] tvp5150: add HW input connectors support"
> > 
> > Marco Felsch (7):
> >   media: tvp5150: fix irq_request error path during probe
> >   media: tvp5150: add input source selection of_graph support
> >   media: dt-bindings: tvp5150: Add input port connectors DT bindings
> >   media: v4l2-subdev: add stubs for v4l2_subdev_get_try_*
> >   media: v4l2-subdev: fix v4l2_subdev_get_try_* dependency
> >   media: tvp5150: add FORMAT_TRY support for get/set selection handlers
> >   media: tvp5150: add s_power callback
> > 
> > Michael Tretter (1):
> >   media: tvp5150: initialize subdev before parsing device tree
> > 
> >  .../devicetree/bindings/media/i2c/tvp5150.txt |  92 ++-
> >  drivers/media/i2c/tvp5150.c                   | 657 +++++++++++++-----
> >  include/dt-bindings/media/tvp5150.h           |   2 -
> >  include/media/v4l2-subdev.h                   |  15 +-
> >  4 files changed, 584 insertions(+), 182 deletions(-)
> > 
> > -- 
> > 2.19.0
> > 
> > 
> > 
> 
> -- 
> Pengutronix e.K.                           |                             |
> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

Re: [PATCH v3 0/9] TVP5150 fixes and new features

[Mauro Carvalho Chehab]

Hi Marco,

Em Fri, 9 Nov 2018 14:46:24 +0100
Marco Felsch <m.felsch@pengutronix.de> escreveu:

> Hi Mauro,
> 
> I don't want to spam you. Can you give me some feedback? I know the
> merge window is a busy time, so maybe you have some time now.

Sorry for taking so long on looking into it... has been really busy
those days :-(

I applied patch 2/9. Patch 3 doesn't apply. Would you mind
rebasing it on the top of upstream? there are some non-trivial
conflicts (perhaps I just missed some other preparation patch?).

I suspect that it would be easier if you could rebase your tree
on the top of the latest upstream one, e. g.:

	git://linuxtv.org/media_tree.git
	
(master branch)

Regards,
Mauro
> 
> Regards,
> Marco
> 
> On 18-10-29 19:41, Marco Felsch wrote:
> > Hi Mauro,
> > 
> > just a reminder, Rob already added his ack/rev-by tags.
> > 
> > Thanks,
> > Marco
> > 
> > On 18-09-18 15:14, Marco Felsch wrote:  
> > > Hi,
> > > 
> > > this is my v3 with the integrated reviews from my v2 [1]. This serie
> > > applies to Mauro's experimental.git [2].
> > > 
> > > @Mauro:
> > > Patch ("media: tvp5150: fix irq_request error path during probe") is new
> > > in this series. Maybe you can squash them with ("media: tvp5150: Add sync lock
> > > interrupt handling"), thanks.
> > > 
> > > I've tested this series on a customer dt-based board. Unfortunately I
> > > haven't a device which use the em28xx driver. So other tester a welcome :)
> > > 
> > > [1] https://www.spinics.net/lists/devicetree/msg244129.html
> > > [2] https://git.linuxtv.org/mchehab/experimental.git/log/?h=tvp5150-4
> > > 
> > > Javier Martinez Canillas (1):
> > >   partial revert of "[media] tvp5150: add HW input connectors support"
> > > 
> > > Marco Felsch (7):
> > >   media: tvp5150: fix irq_request error path during probe
> > >   media: tvp5150: add input source selection of_graph support
> > >   media: dt-bindings: tvp5150: Add input port connectors DT bindings
> > >   media: v4l2-subdev: add stubs for v4l2_subdev_get_try_*
> > >   media: v4l2-subdev: fix v4l2_subdev_get_try_* dependency
> > >   media: tvp5150: add FORMAT_TRY support for get/set selection handlers
> > >   media: tvp5150: add s_power callback
> > > 
> > > Michael Tretter (1):
> > >   media: tvp5150: initialize subdev before parsing device tree
> > > 
> > >  .../devicetree/bindings/media/i2c/tvp5150.txt |  92 ++-
> > >  drivers/media/i2c/tvp5150.c                   | 657 +++++++++++++-----
> > >  include/dt-bindings/media/tvp5150.h           |   2 -
> > >  include/media/v4l2-subdev.h                   |  15 +-
> > >  4 files changed, 584 insertions(+), 182 deletions(-)
> > > 
> > > -- 
> > > 2.19.0
> > > 
> > > 
> > >   
> > 
> > -- 
> > Pengutronix e.K.                           |                             |
> > Industrial Linux Solutions                 | http://www.pengutronix.de/  |
> > Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
> > Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
> > 
> >   
> 



Thanks,
Mauro