[PATCH v2 03/10] mtd: cfi_cmdset_0002: Remove goto statement from do_write_buffer()

[Tokunori Ikegami <ikegami@allied-telesis.co.jp>]

For a maintainability by reducing the goto statement remove it from
do_write_buffer().

Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Fabio Bettoni <fbettoni@gmail.com>
Co: Hauke Mehrtens <hauke@hauke-m.de>
Co: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: linux-mtd@lists.infradead.org
---
Changes since v1:
- Split the patch v1 3/3.

 drivers/mtd/chips/cfi_cmdset_0002.c | 46 +++++++++++++++--------------
 1 file changed, 24 insertions(+), 22 deletions(-)

diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c
index c2e51768a02c..deffafab067e 100644
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -1884,38 +1884,40 @@ static int __xipram do_write_buffer(struct map_info *map, struct flchip *chip,
 
 		if (chip_good(map, adr, datum)) {
 			xip_enable(map, chip, adr);
-			goto op_done;
+			break;
 		}
 
-		if (time_after(jiffies, timeo))
+		if (time_after(jiffies, timeo)) {
+			ret = -EIO;
 			break;
+		}
 
 		/* Latency issues. Drop the lock, wait a while and retry */
 		UDELAY(map, chip, adr, 1);
 	}
 
-	/*
-	 * Recovery from write-buffer programming failures requires
-	 * the write-to-buffer-reset sequence.  Since the last part
-	 * of the sequence also works as a normal reset, we can run
-	 * the same commands regardless of why we are here.
-	 * See e.g.
-	 * http://www.spansion.com/Support/Application%20Notes/MirrorBit_Write_Buffer_Prog_Page_Buffer_Read_AN.pdf
-	 */
-	cfi_send_gen_cmd(0xAA, cfi->addr_unlock1, chip->start, map, cfi,
-			 cfi->device_type, NULL);
-	cfi_send_gen_cmd(0x55, cfi->addr_unlock2, chip->start, map, cfi,
-			 cfi->device_type, NULL);
-	cfi_send_gen_cmd(0xF0, cfi->addr_unlock1, chip->start, map, cfi,
-			 cfi->device_type, NULL);
-	xip_enable(map, chip, adr);
-	/* FIXME - should have reset delay before continuing */
+	if (ret) {
+		/*
+		 * Recovery from write-buffer programming failures requires
+		 * the write-to-buffer-reset sequence.  Since the last part
+		 * of the sequence also works as a normal reset, we can run
+		 * the same commands regardless of why we are here.
+		 * See e.g.
+		 * http://www.spansion.com/Support/Application%20Notes/MirrorBit_Write_Buffer_Prog_Page_Buffer_Read_AN.pdf
+		 */
+		cfi_send_gen_cmd(0xAA, cfi->addr_unlock1, chip->start, map, cfi,
+				 cfi->device_type, NULL);
+		cfi_send_gen_cmd(0x55, cfi->addr_unlock2, chip->start, map, cfi,
+				 cfi->device_type, NULL);
+		cfi_send_gen_cmd(0xF0, cfi->addr_unlock1, chip->start, map, cfi,
+				 cfi->device_type, NULL);
+		xip_enable(map, chip, adr);
+		/* FIXME - should have reset delay before continuing */
 
-	printk(KERN_WARNING "MTD %s(): software timeout, address:0x%.8lx.\n",
-	       __func__, adr);
+		printk(KERN_WARNING "MTD %s(): software timeout, address:0x%.8lx.\n",
+		       __func__, adr);
+	}
 
-	ret = -EIO;
- op_done:
 	chip->state = FL_READY;
 	DISABLE_VPP(map);
 	put_chip(map, chip, adr);
-- 
2.18.0