[PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Alex Gonzalez]

Add support for a LVDS panel accessory kit consisting of:

* AU Optronics G101EVN010 10.1 inches TFT-LCD display
* Goodix GT911 capacitive touch controller

This is used with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.

Changes in v1 from initial changeset [1]:

* Split configuration change into a different commit
* Provide meaningful commit messages
* Use the new DRM mxsfb driver for the AUO G101EVN010 panel

[1] https://lore.kernel.org/lkml/1540204399-12982-1-git-send-email-alex.gonzalez@digi.com/

Alex Gonzalez (4):
  drm/panel: simple: Add AUO G101EVN010 panel support
  ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
  ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
  ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

 .../bindings/display/panel/auo,g101evn010          | 12 +++++++
 arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts        | 37 ++++++++++++++++++++++
 arch/arm/configs/imx_v6_v7_defconfig               |  1 +
 drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++
 4 files changed, 77 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010

[PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Alex Gonzalez]

Add support for a LVDS panel accessory kit consisting of:

* AU Optronics G101EVN010 10.1 inches TFT-LCD display
* Goodix GT911 capacitive touch controller

This is used with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.

Changes in v1 from initial changeset [1]:

* Split configuration change into a different commit
* Provide meaningful commit messages
* Use the new DRM mxsfb driver for the AUO G101EVN010 panel

[1] https://lore.kernel.org/lkml/1540204399-12982-1-git-send-email-alex.gonzalez@digi.com/

Alex Gonzalez (4):
  drm/panel: simple: Add AUO G101EVN010 panel support
  ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
  ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
  ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

 .../bindings/display/panel/auo,g101evn010          | 12 +++++++
 arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts        | 37 ++++++++++++++++++++++
 arch/arm/configs/imx_v6_v7_defconfig               |  1 +
 drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++
 4 files changed, 77 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010

[PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Alex Gonzalez]

Add support for a LVDS panel accessory kit consisting of:

* AU Optronics G101EVN010 10.1 inches TFT-LCD display
* Goodix GT911 capacitive touch controller

This is used with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.

Changes in v1 from initial changeset [1]:

* Split configuration change into a different commit
* Provide meaningful commit messages
* Use the new DRM mxsfb driver for the AUO G101EVN010 panel

[1] https://lore.kernel.org/lkml/1540204399-12982-1-git-send-email-alex.gonzalez at digi.com/

Alex Gonzalez (4):
  drm/panel: simple: Add AUO G101EVN010 panel support
  ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
  ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
  ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

 .../bindings/display/panel/auo,g101evn010          | 12 +++++++
 arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts        | 37 ++++++++++++++++++++++
 arch/arm/configs/imx_v6_v7_defconfig               |  1 +
 drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++
 4 files changed, 77 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010

[PATCH v1 1/4] drm/panel: simple: Add AUO G101EVN010 panel support

[Alex Gonzalez]

The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
panel.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 .../bindings/display/panel/auo,g101evn010          | 12 ++++++++++
 drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++++++++
 2 files changed, 39 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010

diff --git a/Documentation/devicetree/bindings/display/panel/auo,g101evn010 b/Documentation/devicetree/bindings/display/panel/auo,g101evn010
new file mode 100644
index 000000000000..bc6a0c858e23
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/auo,g101evn010
@@ -0,0 +1,12 @@
+AU Optronics Corporation 10.1" (1280x800) color TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,g101evn010"
+- power-supply: as specified in the base binding
+
+Optional properties:
+- backlight: as specified in the base binding
+- enable-gpios: as specified in the base binding
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 97964f7f2ace..65a0dd166637 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -631,6 +631,30 @@ static const struct panel_desc auo_g104sn02 = {
 	},
 };
 
+static const struct drm_display_mode auo_g101evn010_mode = {
+	.clock = 68930,
+	.hdisplay = 1280,
+	.hsync_start = 1280 + 82,
+	.hsync_end = 1280 + 82 + 2,
+	.htotal = 1280 + 82 + 2 + 84,
+	.vdisplay = 800,
+	.vsync_start = 800 + 8,
+	.vsync_end = 800 + 8 + 2,
+	.vtotal = 800 + 8 + 2 + 6,
+	.vrefresh = 60,
+};
+
+static const struct panel_desc auo_g101evn010 = {
+	.modes = &auo_g101evn010_mode,
+	.num_modes = 1,
+	.bpc = 6,
+	.size = {
+		.width = 216,
+		.height = 135,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
+};
+
 static const struct display_timing auo_g133han01_timings = {
 	.pixelclock = { 134000000, 141200000, 149000000 },
 	.hactive = { 1920, 1920, 1920 },
@@ -2355,6 +2379,9 @@ static const struct of_device_id platform_of_match[] = {
 		.compatible = "auo,g104sn02",
 		.data = &auo_g104sn02,
 	}, {
+		.compatible = "auo,g101evn010",
+		.data = &auo_g101evn010,
+	}, {
 		.compatible = "auo,g133han01",
 		.data = &auo_g133han01,
 	}, {

[PATCH v1 1/4] drm/panel: simple: Add AUO G101EVN010 panel support

[Alex Gonzalez]

The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
panel.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 .../bindings/display/panel/auo,g101evn010          | 12 ++++++++++
 drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++++++++
 2 files changed, 39 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010

diff --git a/Documentation/devicetree/bindings/display/panel/auo,g101evn010 b/Documentation/devicetree/bindings/display/panel/auo,g101evn010
new file mode 100644
index 000000000000..bc6a0c858e23
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/auo,g101evn010
@@ -0,0 +1,12 @@
+AU Optronics Corporation 10.1" (1280x800) color TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,g101evn010"
+- power-supply: as specified in the base binding
+
+Optional properties:
+- backlight: as specified in the base binding
+- enable-gpios: as specified in the base binding
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 97964f7f2ace..65a0dd166637 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -631,6 +631,30 @@ static const struct panel_desc auo_g104sn02 = {
 	},
 };
 
+static const struct drm_display_mode auo_g101evn010_mode = {
+	.clock = 68930,
+	.hdisplay = 1280,
+	.hsync_start = 1280 + 82,
+	.hsync_end = 1280 + 82 + 2,
+	.htotal = 1280 + 82 + 2 + 84,
+	.vdisplay = 800,
+	.vsync_start = 800 + 8,
+	.vsync_end = 800 + 8 + 2,
+	.vtotal = 800 + 8 + 2 + 6,
+	.vrefresh = 60,
+};
+
+static const struct panel_desc auo_g101evn010 = {
+	.modes = &auo_g101evn010_mode,
+	.num_modes = 1,
+	.bpc = 6,
+	.size = {
+		.width = 216,
+		.height = 135,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
+};
+
 static const struct display_timing auo_g133han01_timings = {
 	.pixelclock = { 134000000, 141200000, 149000000 },
 	.hactive = { 1920, 1920, 1920 },
@@ -2355,6 +2379,9 @@ static const struct of_device_id platform_of_match[] = {
 		.compatible = "auo,g104sn02",
 		.data = &auo_g104sn02,
 	}, {
+		.compatible = "auo,g101evn010",
+		.data = &auo_g101evn010,
+	}, {
 		.compatible = "auo,g133han01",
 		.data = &auo_g133han01,
 	}, {

[PATCH v1 1/4] drm/panel: simple: Add AUO G101EVN010 panel support

[Alex Gonzalez]

The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
panel.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 .../bindings/display/panel/auo,g101evn010          | 12 ++++++++++
 drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++++++++
 2 files changed, 39 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010

diff --git a/Documentation/devicetree/bindings/display/panel/auo,g101evn010 b/Documentation/devicetree/bindings/display/panel/auo,g101evn010
new file mode 100644
index 000000000000..bc6a0c858e23
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/auo,g101evn010
@@ -0,0 +1,12 @@
+AU Optronics Corporation 10.1" (1280x800) color TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,g101evn010"
+- power-supply: as specified in the base binding
+
+Optional properties:
+- backlight: as specified in the base binding
+- enable-gpios: as specified in the base binding
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 97964f7f2ace..65a0dd166637 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -631,6 +631,30 @@ static const struct panel_desc auo_g104sn02 = {
 	},
 };
 
+static const struct drm_display_mode auo_g101evn010_mode = {
+	.clock = 68930,
+	.hdisplay = 1280,
+	.hsync_start = 1280 + 82,
+	.hsync_end = 1280 + 82 + 2,
+	.htotal = 1280 + 82 + 2 + 84,
+	.vdisplay = 800,
+	.vsync_start = 800 + 8,
+	.vsync_end = 800 + 8 + 2,
+	.vtotal = 800 + 8 + 2 + 6,
+	.vrefresh = 60,
+};
+
+static const struct panel_desc auo_g101evn010 = {
+	.modes = &auo_g101evn010_mode,
+	.num_modes = 1,
+	.bpc = 6,
+	.size = {
+		.width = 216,
+		.height = 135,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
+};
+
 static const struct display_timing auo_g133han01_timings = {
 	.pixelclock = { 134000000, 141200000, 149000000 },
 	.hactive = { 1920, 1920, 1920 },
@@ -2355,6 +2379,9 @@ static const struct of_device_id platform_of_match[] = {
 		.compatible = "auo,g104sn02",
 		.data = &auo_g104sn02,
 	}, {
+		.compatible = "auo,g101evn010",
+		.data = &auo_g101evn010,
+	}, {
 		.compatible = "auo,g133han01",
 		.data = &auo_g133han01,
 	}, {

[PATCH v1 2/4] ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel

[Alex Gonzalez]

This change adds support for the AUO G101EVN010 lcdif panel for the
mxsfb DRM driver.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
index 11966d12af76..f6e6b2cf780b 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
+++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
@@ -24,6 +24,18 @@
 		status = "okay";
 	};
 
+	panel {
+		compatible = "auo,g101evn010", "simple-panel";
+		power-supply = <&ldo4_ext>;
+		backlight = <&lcd_backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_usb_otg1_vbus: regulator-usb-otg1 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
@@ -112,6 +124,12 @@
 		     &pinctrl_lcdif_hvsync>;
 	lcd-supply = <&ldo4_ext>;       /* BU90T82 LVDS bridge power */
 	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
 };
 
 &ldo4_ext {

[PATCH v1 2/4] ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel

[Alex Gonzalez]

This change adds support for the AUO G101EVN010 lcdif panel for the
mxsfb DRM driver.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
index 11966d12af76..f6e6b2cf780b 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
+++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
@@ -24,6 +24,18 @@
 		status = "okay";
 	};
 
+	panel {
+		compatible = "auo,g101evn010", "simple-panel";
+		power-supply = <&ldo4_ext>;
+		backlight = <&lcd_backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_usb_otg1_vbus: regulator-usb-otg1 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
@@ -112,6 +124,12 @@
 		     &pinctrl_lcdif_hvsync>;
 	lcd-supply = <&ldo4_ext>;       /* BU90T82 LVDS bridge power */
 	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
 };
 
 &ldo4_ext {

[PATCH v1 2/4] ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel

[Alex Gonzalez]

This change adds support for the AUO G101EVN010 lcdif panel for the
mxsfb DRM driver.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
index 11966d12af76..f6e6b2cf780b 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
+++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
@@ -24,6 +24,18 @@
 		status = "okay";
 	};
 
+	panel {
+		compatible = "auo,g101evn010", "simple-panel";
+		power-supply = <&ldo4_ext>;
+		backlight = <&lcd_backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_usb_otg1_vbus: regulator-usb-otg1 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
@@ -112,6 +124,12 @@
 		     &pinctrl_lcdif_hvsync>;
 	lcd-supply = <&ldo4_ext>;       /* BU90T82 LVDS bridge power */
 	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
 };
 
 &ldo4_ext {

[PATCH v1 3/4] ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX

[Alex Gonzalez]

Select CONFIG_TOUCHSCREEN_GOODIX so that we can have functional touch
screen by default on Digi International's AUO/Goodix LCD accessory kit used
with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 arch/arm/configs/imx_v6_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 7eca43ff69bb..d6e947307d67 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -170,6 +170,7 @@ CONFIG_MOUSE_PS2_ELANTECH=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ADS7846=y
 CONFIG_TOUCHSCREEN_EGALAX=y
+CONFIG_TOUCHSCREEN_GOODIX=y
 CONFIG_TOUCHSCREEN_MAX11801=y
 CONFIG_TOUCHSCREEN_IMX6UL_TSC=y
 CONFIG_TOUCHSCREEN_EDT_FT5X06=y

[PATCH v1 3/4] ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX

[Alex Gonzalez]

Select CONFIG_TOUCHSCREEN_GOODIX so that we can have functional touch
screen by default on Digi International's AUO/Goodix LCD accessory kit used
with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 arch/arm/configs/imx_v6_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 7eca43ff69bb..d6e947307d67 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -170,6 +170,7 @@ CONFIG_MOUSE_PS2_ELANTECH=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ADS7846=y
 CONFIG_TOUCHSCREEN_EGALAX=y
+CONFIG_TOUCHSCREEN_GOODIX=y
 CONFIG_TOUCHSCREEN_MAX11801=y
 CONFIG_TOUCHSCREEN_IMX6UL_TSC=y
 CONFIG_TOUCHSCREEN_EDT_FT5X06=y

[PATCH v1 3/4] ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX

[Alex Gonzalez]

Select CONFIG_TOUCHSCREEN_GOODIX so that we can have functional touch
screen by default on Digi International's AUO/Goodix LCD accessory kit used
with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 arch/arm/configs/imx_v6_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 7eca43ff69bb..d6e947307d67 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -170,6 +170,7 @@ CONFIG_MOUSE_PS2_ELANTECH=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ADS7846=y
 CONFIG_TOUCHSCREEN_EGALAX=y
+CONFIG_TOUCHSCREEN_GOODIX=y
 CONFIG_TOUCHSCREEN_MAX11801=y
 CONFIG_TOUCHSCREEN_IMX6UL_TSC=y
 CONFIG_TOUCHSCREEN_EDT_FT5X06=y

[PATCH v1 4/4] ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

[Alex Gonzalez]

The ConnectCore 6UL SBC Pro has an AUO/Goodix LCD accessory kit that is
connected on the LVDS interface through an on-board LVDS transceiver.

This change adds support for the touch interface.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
index f6e6b2cf780b..3749fdda3611 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
+++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
@@ -117,6 +117,19 @@
 	};
 };
 
+&i2c1 {
+	touchscreen@14 {
+		compatible = "goodix,gt911";
+		reg = <0x14>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_goodix_touch>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+		irq-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+};
+
 &lcdif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcdif_dat0_17
@@ -290,6 +303,12 @@
 		>;
 	};
 
+	pinctrl_goodix_touch: goodixgrp{
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1020
+		>;
+	};
+
 	pinctrl_lcdif_dat0_17: lcdifdatgrp0-17 {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79

[PATCH v1 4/4] ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

[Alex Gonzalez]

The ConnectCore 6UL SBC Pro has an AUO/Goodix LCD accessory kit that is
connected on the LVDS interface through an on-board LVDS transceiver.

This change adds support for the touch interface.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
index f6e6b2cf780b..3749fdda3611 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
+++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
@@ -117,6 +117,19 @@
 	};
 };
 
+&i2c1 {
+	touchscreen@14 {
+		compatible = "goodix,gt911";
+		reg = <0x14>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_goodix_touch>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+		irq-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+};
+
 &lcdif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcdif_dat0_17
@@ -290,6 +303,12 @@
 		>;
 	};
 
+	pinctrl_goodix_touch: goodixgrp{
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1020
+		>;
+	};
+
 	pinctrl_lcdif_dat0_17: lcdifdatgrp0-17 {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79

[PATCH v1 4/4] ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

[Alex Gonzalez]

The ConnectCore 6UL SBC Pro has an AUO/Goodix LCD accessory kit that is
connected on the LVDS interface through an on-board LVDS transceiver.

This change adds support for the touch interface.

Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
---
 arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
index f6e6b2cf780b..3749fdda3611 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
+++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
@@ -117,6 +117,19 @@
 	};
 };
 
+&i2c1 {
+	touchscreen at 14 {
+		compatible = "goodix,gt911";
+		reg = <0x14>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_goodix_touch>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+		irq-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+};
+
 &lcdif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcdif_dat0_17
@@ -290,6 +303,12 @@
 		>;
 	};
 
+	pinctrl_goodix_touch: goodixgrp{
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1020
+		>;
+	};
+
 	pinctrl_lcdif_dat0_17: lcdifdatgrp0-17 {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79

Re: [PATCH v1 2/4] ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel

[Fabio Estevam]

On Thu, Oct 25, 2018 at 12:11 PM Alex Gonzalez <alex.gonzalez@digi.com> wrote:
>
> This change adds support for the AUO G101EVN010 lcdif panel for the
> mxsfb DRM driver.
>
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
> ---
>  arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
> index 11966d12af76..f6e6b2cf780b 100644
> --- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
> +++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
> @@ -24,6 +24,18 @@
>                 status = "okay";
>         };
>
> +       panel {
> +               compatible = "auo,g101evn010", "simple-panel";

The "simple-panel" string could be dropped.

Reviewed-by: Fabio Estevam <festevam@gmail.com>


> +               power-supply = <&ldo4_ext>;
> +               backlight = <&lcd_backlight>;
> +
> +               port {
> +                       panel_in: endpoint {
> +                               remote-endpoint = <&display_out>;
> +                       };
> +               };
> +       };
> +
>         reg_usb_otg1_vbus: regulator-usb-otg1 {
>                 compatible = "regulator-fixed";
>                 regulator-name = "usb_otg1_vbus";
> @@ -112,6 +124,12 @@
>                      &pinctrl_lcdif_hvsync>;
>         lcd-supply = <&ldo4_ext>;       /* BU90T82 LVDS bridge power */
>         status = "okay";
> +
> +       port {
> +               display_out: endpoint {
> +                       remote-endpoint = <&panel_in>;
> +               };
> +       };
>  };
>
>  &ldo4_ext {
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 2/4] ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel

[Fabio Estevam]

On Thu, Oct 25, 2018 at 12:11 PM Alex Gonzalez <alex.gonzalez@digi.com> wrote:
>
> This change adds support for the AUO G101EVN010 lcdif panel for the
> mxsfb DRM driver.
>
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
> ---
>  arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
> index 11966d12af76..f6e6b2cf780b 100644
> --- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
> +++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
> @@ -24,6 +24,18 @@
>                 status = "okay";
>         };
>
> +       panel {
> +               compatible = "auo,g101evn010", "simple-panel";

The "simple-panel" string could be dropped.

Reviewed-by: Fabio Estevam <festevam@gmail.com>


> +               power-supply = <&ldo4_ext>;
> +               backlight = <&lcd_backlight>;
> +
> +               port {
> +                       panel_in: endpoint {
> +                               remote-endpoint = <&display_out>;
> +                       };
> +               };
> +       };
> +
>         reg_usb_otg1_vbus: regulator-usb-otg1 {
>                 compatible = "regulator-fixed";
>                 regulator-name = "usb_otg1_vbus";
> @@ -112,6 +124,12 @@
>                      &pinctrl_lcdif_hvsync>;
>         lcd-supply = <&ldo4_ext>;       /* BU90T82 LVDS bridge power */
>         status = "okay";
> +
> +       port {
> +               display_out: endpoint {
> +                       remote-endpoint = <&panel_in>;
> +               };
> +       };
>  };
>
>  &ldo4_ext {
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 2/4] ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel

[Fabio Estevam]

On Thu, Oct 25, 2018 at 12:11 PM Alex Gonzalez <alex.gonzalez@digi.com> wrote:
>
> This change adds support for the AUO G101EVN010 lcdif panel for the
> mxsfb DRM driver.
>
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
> ---
>  arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
> index 11966d12af76..f6e6b2cf780b 100644
> --- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
> +++ b/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
> @@ -24,6 +24,18 @@
>                 status = "okay";
>         };
>
> +       panel {
> +               compatible = "auo,g101evn010", "simple-panel";

The "simple-panel" string could be dropped.

Reviewed-by: Fabio Estevam <festevam@gmail.com>


> +               power-supply = <&ldo4_ext>;
> +               backlight = <&lcd_backlight>;
> +
> +               port {
> +                       panel_in: endpoint {
> +                               remote-endpoint = <&display_out>;
> +                       };
> +               };
> +       };
> +
>         reg_usb_otg1_vbus: regulator-usb-otg1 {
>                 compatible = "regulator-fixed";
>                 regulator-name = "usb_otg1_vbus";
> @@ -112,6 +124,12 @@
>                      &pinctrl_lcdif_hvsync>;
>         lcd-supply = <&ldo4_ext>;       /* BU90T82 LVDS bridge power */
>         status = "okay";
> +
> +       port {
> +               display_out: endpoint {
> +                       remote-endpoint = <&panel_in>;
> +               };
> +       };
>  };
>
>  &ldo4_ext {
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 3/4] ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX

[Fabio Estevam]

On Thu, Oct 25, 2018 at 12:11 PM Alex Gonzalez <alex.gonzalez@digi.com> wrote:
>
> Select CONFIG_TOUCHSCREEN_GOODIX so that we can have functional touch
> screen by default on Digi International's AUO/Goodix LCD accessory kit used
> with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.
>
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>

Reviewed-by: Fabio Estevam <festevam@gmail.com>

Re: [PATCH v1 3/4] ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX

[Fabio Estevam]

On Thu, Oct 25, 2018 at 12:11 PM Alex Gonzalez <alex.gonzalez@digi.com> wrote:
>
> Select CONFIG_TOUCHSCREEN_GOODIX so that we can have functional touch
> screen by default on Digi International's AUO/Goodix LCD accessory kit used
> with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.
>
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>

Reviewed-by: Fabio Estevam <festevam@gmail.com>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v1 3/4] ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX

[Fabio Estevam]

On Thu, Oct 25, 2018 at 12:11 PM Alex Gonzalez <alex.gonzalez@digi.com> wrote:
>
> Select CONFIG_TOUCHSCREEN_GOODIX so that we can have functional touch
> screen by default on Digi International's AUO/Goodix LCD accessory kit used
> with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.
>
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>

Reviewed-by: Fabio Estevam <festevam@gmail.com>

Re: [PATCH v1 4/4] ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

[Fabio Estevam]

On Thu, Oct 25, 2018 at 12:10 PM Alex Gonzalez <alex.gonzalez@digi.com> wrote:
>
> The ConnectCore 6UL SBC Pro has an AUO/Goodix LCD accessory kit that is
> connected on the LVDS interface through an on-board LVDS transceiver.
>
> This change adds support for the touch interface.
>
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>

Reviewed-by: Fabio Estevam <festevam@gmail.com>

Re: [PATCH v1 4/4] ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

[Fabio Estevam]

On Thu, Oct 25, 2018 at 12:10 PM Alex Gonzalez <alex.gonzalez@digi.com> wrote:
>
> The ConnectCore 6UL SBC Pro has an AUO/Goodix LCD accessory kit that is
> connected on the LVDS interface through an on-board LVDS transceiver.
>
> This change adds support for the touch interface.
>
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>

Reviewed-by: Fabio Estevam <festevam@gmail.com>

[PATCH v1 4/4] ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

[Fabio Estevam]

On Thu, Oct 25, 2018 at 12:10 PM Alex Gonzalez <alex.gonzalez@digi.com> wrote:
>
> The ConnectCore 6UL SBC Pro has an AUO/Goodix LCD accessory kit that is
> connected on the LVDS interface through an on-board LVDS transceiver.
>
> This change adds support for the touch interface.
>
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>

Reviewed-by: Fabio Estevam <festevam@gmail.com>

Re: [PATCH v1 1/4] drm/panel: simple: Add AUO G101EVN010 panel support

[Rob Herring]

On Thu, 25 Oct 2018 17:09:30 +0200, Alex Gonzalez wrote:
> The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
> panel.
> 
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
> ---
>  .../bindings/display/panel/auo,g101evn010          | 12 ++++++++++
>  drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++++++++
>  2 files changed, 39 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v1 1/4] drm/panel: simple: Add AUO G101EVN010 panel support

[Rob Herring]

On Thu, 25 Oct 2018 17:09:30 +0200, Alex Gonzalez wrote:
> The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
> panel.
> 
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
> ---
>  .../bindings/display/panel/auo,g101evn010          | 12 ++++++++++
>  drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++++++++
>  2 files changed, 39 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v1 1/4] drm/panel: simple: Add AUO G101EVN010 panel support

[Rob Herring]

On Thu, 25 Oct 2018 17:09:30 +0200, Alex Gonzalez wrote:
> The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
> panel.
> 
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
> ---
>  .../bindings/display/panel/auo,g101evn010          | 12 ++++++++++
>  drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++++++++
>  2 files changed, 39 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Shawn Guo]

On Thu, Oct 25, 2018 at 05:09:29PM +0200, Alex Gonzalez wrote:
> Alex Gonzalez (4):
>   drm/panel: simple: Add AUO G101EVN010 panel support
>   ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
>   ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
>   ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

It looks good to me.  Ping me when the patch #1 gets accepted and I
will apply the test then.

Shawn

Re: [PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Shawn Guo]

On Thu, Oct 25, 2018 at 05:09:29PM +0200, Alex Gonzalez wrote:
> Alex Gonzalez (4):
>   drm/panel: simple: Add AUO G101EVN010 panel support
>   ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
>   ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
>   ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

It looks good to me.  Ping me when the patch #1 gets accepted and I
will apply the test then.

Shawn
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Shawn Guo]

On Thu, Oct 25, 2018 at 05:09:29PM +0200, Alex Gonzalez wrote:
> Alex Gonzalez (4):
>   drm/panel: simple: Add AUO G101EVN010 panel support
>   ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
>   ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
>   ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

It looks good to me.  Ping me when the patch #1 gets accepted and I
will apply the test then.

Shawn

Re: [PATCH v1 1/4] drm/panel: simple: Add AUO G101EVN010 panel support

[Gonzalez, Alex]

On Tue, Oct 30, 2018 at 11:05:19PM +0000, Rob Herring wrote:
>On Thu, 25 Oct 2018 17:09:30 +0200, Alex Gonzalez wrote:
>> The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
>> panel.
>>
>> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
>> ---
>>  .../bindings/display/panel/auo,g101evn010          | 12 ++++++++++
>>  drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++++++++
>>  2 files changed, 39 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010
>>
>
>Reviewed-by: Rob Herring <robh@kernel.org>

Ping?
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v1 1/4] drm/panel: simple: Add AUO G101EVN010 panel support

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 895 bytes --]

On Thu, Oct 25, 2018 at 05:09:30PM +0200, Alex Gonzalez wrote:
> The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
> panel.
> 
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
> ---
>  .../bindings/display/panel/auo,g101evn010          | 12 ++++++++++
>  drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++++++++
>  2 files changed, 39 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010

Two things to keep in mind for next time: please split up DT bindings
and driver changes into two separate patches (checkpatch.pl warns about
this) and keep entries in panel-simple sorted alphabetically.

I fixed the sorting myself and also added a .txt suffix to the DT
binding documentation for consistency with other files in that
directory.

Applied to drm-misc-next, thanks.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v1 1/4] drm/panel: simple: Add AUO G101EVN010 panel support

[Thierry Reding]

[-- Attachment #1.1: Type: text/plain, Size: 895 bytes --]

On Thu, Oct 25, 2018 at 05:09:30PM +0200, Alex Gonzalez wrote:
> The change adds support for the AU Optronics G101EVN010 10.1" TFT LCD
> panel.
> 
> Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
> ---
>  .../bindings/display/panel/auo,g101evn010          | 12 ++++++++++
>  drivers/gpu/drm/panel/panel-simple.c               | 27 ++++++++++++++++++++++
>  2 files changed, 39 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/auo,g101evn010

Two things to keep in mind for next time: please split up DT bindings
and driver changes into two separate patches (checkpatch.pl warns about
this) and keep entries in panel-simple sorted alphabetically.

I fixed the sorting myself and also added a .txt suffix to the DT
binding documentation for consistency with other files in that
directory.

Applied to drm-misc-next, thanks.

Thierry

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Gonzalez, Alex]

On Sun, Nov 04, 2018 at 08:54:26AM +0000, Shawn Guo wrote:
>On Thu, Oct 25, 2018 at 05:09:29PM +0200, Alex Gonzalez wrote:
>> Alex Gonzalez (4):
>>   drm/panel: simple: Add AUO G101EVN010 panel support
>>   ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
>>   ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
>>   ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller
>
>It looks good to me.  Ping me when the patch #1 gets accepted and I
>will apply the test then.
>
>Shawn

Hi Shawn,

Patch #1 is already applied to drm-misc-next (thanks to Thierry for fixing it 
up for me)

Alex

Re: [PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Gonzalez, Alex]

On Sun, Nov 04, 2018 at 08:54:26AM +0000, Shawn Guo wrote:
>On Thu, Oct 25, 2018 at 05:09:29PM +0200, Alex Gonzalez wrote:
>> Alex Gonzalez (4):
>>   drm/panel: simple: Add AUO G101EVN010 panel support
>>   ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
>>   ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
>>   ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller
>
>It looks good to me.  Ping me when the patch #1 gets accepted and I
>will apply the test then.
>
>Shawn

Hi Shawn,

Patch #1 is already applied to drm-misc-next (thanks to Thierry for fixing it 
up for me)

Alex
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Gonzalez, Alex]

On Sun, Nov 04, 2018 at 08:54:26AM +0000, Shawn Guo wrote:
>On Thu, Oct 25, 2018 at 05:09:29PM +0200, Alex Gonzalez wrote:
>> Alex Gonzalez (4):
>>   drm/panel: simple: Add AUO G101EVN010 panel support
>>   ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
>>   ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
>>   ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller
>
>It looks good to me.  Ping me when the patch #1 gets accepted and I
>will apply the test then.
>
>Shawn

Hi Shawn,

Patch #1 is already applied to drm-misc-next (thanks to Thierry for fixing it 
up for me)

Alex
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Shawn Guo]

On Thu, Oct 25, 2018 at 05:09:29PM +0200, Alex Gonzalez wrote:
> Alex Gonzalez (4):
>   drm/panel: simple: Add AUO G101EVN010 panel support
>   ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
>   ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
>   ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

Applied #2 ~ #4, thanks.

Re: [PATCH v1 0/4] ARM: dts: ccimx6ulsbcpro: Add 10" AUO/Goodix LVDS panel accessory kit

[Shawn Guo]

On Thu, Oct 25, 2018 at 05:09:29PM +0200, Alex Gonzalez wrote:
> Alex Gonzalez (4):
>   drm/panel: simple: Add AUO G101EVN010 panel support
>   ARM: dts: ccimx6ulsbcpro: Enable AUO G101EVN010 lcdif panel
>   ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
>   ARM: dts: ccimx6ulsbcpro: Add support for Goodix touch controller

Applied #2 ~ #4, thanks.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel