From: Jagan Teki <jagan@amarulasolutions.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 1/2] arm64: allwinner: h6: Add common orangepi nodes into dtsi
Date: Mon, 5 Nov 2018 13:20:39 +0530 [thread overview]
Message-ID: <20181105075040.22463-1-jagan@amarulasolutions.com> (raw)
Based on the information from hardware schematics and orangepi
vendor orangepi H6 boards, One Plus and Lite2 shares common nodes
like axp805, uart, mmc0 etc. The common differences between them is
- One Plus, has Ethernet
- Lite2, has Wifi, USB3, CSI port.
So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that
it case use on respective orangepi h6 board dts files.
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/sun50i-h6-orangepi-one-plus.dts | 140 +----------------
arch/arm/dts/sun50i-h6-orangepi.dtsi | 150 +++++++++++++++++++
2 files changed, 151 insertions(+), 139 deletions(-)
create mode 100644 arch/arm/dts/sun50i-h6-orangepi.dtsi
diff --git a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
index 0612c19cd9..12e17567ab 100644
--- a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
+++ b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
@@ -4,147 +4,9 @@
* Author: Jagan Teki <jagan@amarulasolutions.com>
*/
-/dts-v1/;
-
-#include "sun50i-h6.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
+#include "sun50i-h6-orangepi.dtsi"
/ {
model = "OrangePi One Plus";
compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <®_cldo1>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
- bus-width = <4>;
- status = "okay";
-};
-
-&r_i2c {
- status = "okay";
-
- axp805: pmic at 36 {
- compatible = "x-powers,axp805", "x-powers,axp806";
- reg = <0x36>;
- interrupt-parent = <&r_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <1>;
- x-powers,self-working-mode;
-
- regulators {
- reg_aldo1: aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-pl";
- };
-
- reg_aldo2: aldo2 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-ac200";
- };
-
- reg_aldo3: aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc25-dram";
- };
-
- reg_bldo1: bldo1 {
- regulator-always-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-bias-pll";
- };
-
- reg_bldo2: bldo2 {
- regulator-always-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-efuse-pcie-hdmi-io";
- };
-
- reg_bldo3: bldo3 {
- regulator-always-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-dcxoio";
- };
-
- bldo4 {
- /* unused */
- };
-
- reg_cldo1: cldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-3v3";
- };
-
- reg_cldo2: cldo2 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi-1";
- };
-
- reg_cldo3: cldo3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi-2";
- };
-
- reg_dcdca: dcdca {
- regulator-always-on;
- regulator-min-microvolt = <810000>;
- regulator-max-microvolt = <1080000>;
- regulator-name = "vdd-cpu";
- };
-
- reg_dcdcc: dcdcc {
- regulator-min-microvolt = <810000>;
- regulator-max-microvolt = <1080000>;
- regulator-name = "vdd-gpu";
- };
-
- reg_dcdcd: dcdcd {
- regulator-always-on;
- regulator-min-microvolt = <960000>;
- regulator-max-microvolt = <960000>;
- regulator-name = "vdd-sys";
- };
-
- reg_dcdce: dcdce {
- regulator-always-on;
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-name = "vcc-dram";
- };
-
- sw {
- /* unused */
- };
- };
- };
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_ph_pins>;
- status = "okay";
};
diff --git a/arch/arm/dts/sun50i-h6-orangepi.dtsi b/arch/arm/dts/sun50i-h6-orangepi.dtsi
new file mode 100644
index 0000000000..0612c19cd9
--- /dev/null
+++ b/arch/arm/dts/sun50i-h6-orangepi.dtsi
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2018 Amarula Solutions
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "OrangePi One Plus";
+ compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_cldo1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp805: pmic at 36 {
+ compatible = "x-powers,axp805", "x-powers,axp806";
+ reg = <0x36>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ x-powers,self-working-mode;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ac200";
+ };
+
+ reg_aldo3: aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc25-dram";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-bias-pll";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-efuse-pcie-hdmi-io";
+ };
+
+ reg_bldo3: bldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dcxoio";
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ reg_cldo1: cldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-1";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <960000>;
+ regulator-max-microvolt = <960000>;
+ regulator-name = "vdd-sys";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
--
2.18.0.321.gffc6fa0e3
next reply other threads:[~2018-11-05 7:50 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-05 7:50 Jagan Teki [this message]
2018-11-05 7:50 ` [U-Boot] [PATCH 2/2] board: allwinner: sun50i-h6: Add Orangepi Lite2 support Jagan Teki
2018-11-05 15:27 ` Maxime Ripard
2018-11-13 16:44 ` Jagan Teki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181105075040.22463-1-jagan@amarulasolutions.com \
--to=jagan@amarulasolutions.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.