From mboxrd@z Thu Jan 1 00:00:00 1970 From: Simon Glass Date: Mon, 19 Nov 2018 08:53:26 -0700 Subject: [U-Boot] [PATCH 46/93] arm: Remove dreamplug board In-Reply-To: <20181119155413.158098-1-sjg@chromium.org> References: <20181119155413.158098-1-sjg@chromium.org> Message-ID: <20181119155413.158098-47-sjg@chromium.org> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de This board has not been converted to CONFIG_DM_BLK by the deadline. Remove it. Signed-off-by: Simon Glass --- arch/arm/mach-kirkwood/Kconfig | 1 - board/Marvell/dreamplug/Kconfig | 12 --- board/Marvell/dreamplug/MAINTAINERS | 6 -- board/Marvell/dreamplug/Makefile | 10 -- board/Marvell/dreamplug/dreamplug.c | 135 ------------------------- board/Marvell/dreamplug/dreamplug.h | 25 ----- board/Marvell/dreamplug/kwbimage.cfg | 145 --------------------------- configs/dreamplug_defconfig | 40 -------- include/configs/dreamplug.h | 83 --------------- 9 files changed, 457 deletions(-) delete mode 100644 board/Marvell/dreamplug/Kconfig delete mode 100644 board/Marvell/dreamplug/MAINTAINERS delete mode 100644 board/Marvell/dreamplug/Makefile delete mode 100644 board/Marvell/dreamplug/dreamplug.c delete mode 100644 board/Marvell/dreamplug/dreamplug.h delete mode 100644 board/Marvell/dreamplug/kwbimage.cfg delete mode 100644 configs/dreamplug_defconfig delete mode 100644 include/configs/dreamplug.h diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig index d4afdaccd3b..299977c87d6 100644 --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -71,7 +71,6 @@ config SYS_SOC default "kirkwood" source "board/Marvell/openrd/Kconfig" -source "board/Marvell/dreamplug/Kconfig" source "board/buffalo/lsxl/Kconfig" source "board/cloudengines/pogo_e02/Kconfig" source "board/d-link/dns325/Kconfig" diff --git a/board/Marvell/dreamplug/Kconfig b/board/Marvell/dreamplug/Kconfig deleted file mode 100644 index f65ff73713e..00000000000 --- a/board/Marvell/dreamplug/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_DREAMPLUG - -config SYS_BOARD - default "dreamplug" - -config SYS_VENDOR - default "Marvell" - -config SYS_CONFIG_NAME - default "dreamplug" - -endif diff --git a/board/Marvell/dreamplug/MAINTAINERS b/board/Marvell/dreamplug/MAINTAINERS deleted file mode 100644 index 2561ba8134e..00000000000 --- a/board/Marvell/dreamplug/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -DREAMPLUG BOARD -M: Jason Cooper -S: Maintained -F: board/Marvell/dreamplug/ -F: include/configs/dreamplug.h -F: configs/dreamplug_defconfig diff --git a/board/Marvell/dreamplug/Makefile b/board/Marvell/dreamplug/Makefile deleted file mode 100644 index e239d591b7b..00000000000 --- a/board/Marvell/dreamplug/Makefile +++ /dev/null @@ -1,10 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2011 -# Jason Cooper -# -# Based on work by: -# Marvell Semiconductor -# Written-by: Siddarth Gore - -obj-y := dreamplug.o diff --git a/board/Marvell/dreamplug/dreamplug.c b/board/Marvell/dreamplug/dreamplug.c deleted file mode 100644 index ede168c9ece..00000000000 --- a/board/Marvell/dreamplug/dreamplug.c +++ /dev/null @@ -1,135 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2011 - * Jason Cooper - * - * Based on work by: - * Marvell Semiconductor - * Written-by: Siddarth Gore - */ - -#include -#include -#include -#include -#include -#include "dreamplug.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* - * default gpio configuration - * There are maximum 64 gpios controlled through 2 sets of registers - * the below configuration configures mainly initial LED status - */ - mvebu_config_gpio(DREAMPLUG_OE_VAL_LOW, - DREAMPLUG_OE_VAL_HIGH, - DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH); - - /* Multi-Purpose Pins Functionality configuration */ - static const u32 kwmpp_config[] = { - MPP0_SPI_SCn, /* SPI Flash */ - MPP1_SPI_MOSI, - MPP2_SPI_SCK, - MPP3_SPI_MISO, - MPP4_NF_IO6, - MPP5_NF_IO7, - MPP6_SYSRST_OUTn, - MPP7_GPO, - MPP8_TW_SDA, - MPP9_TW_SCK, - MPP10_UART0_TXD, /* Serial */ - MPP11_UART0_RXD, - MPP12_SD_CLK, /* SDIO Slot */ - MPP13_SD_CMD, - MPP14_SD_D0, - MPP15_SD_D1, - MPP16_SD_D2, - MPP17_SD_D3, - MPP18_NF_IO0, - MPP19_NF_IO1, - MPP20_GE1_0, /* Gigabit Ethernet */ - MPP21_GE1_1, - MPP22_GE1_2, - MPP23_GE1_3, - MPP24_GE1_4, - MPP25_GE1_5, - MPP26_GE1_6, - MPP27_GE1_7, - MPP28_GE1_8, - MPP29_GE1_9, - MPP30_GE1_10, - MPP31_GE1_11, - MPP32_GE1_12, - MPP33_GE1_13, - MPP34_GE1_14, - MPP35_GE1_15, - MPP36_GPIO, /* 7 external GPIO pins (36 - 45) */ - MPP37_GPIO, - MPP38_GPIO, - MPP39_GPIO, - MPP40_TDM_SPI_SCK, - MPP41_TDM_SPI_MISO, - MPP42_TDM_SPI_MOSI, - MPP43_GPIO, - MPP44_GPIO, - MPP45_GPIO, - MPP46_GPIO, - MPP47_GPIO, /* Bluetooth LED */ - MPP48_GPIO, /* Wifi LED */ - MPP49_GPIO, /* Wifi AP LED */ - 0 - }; - kirkwood_mpp_conf(kwmpp_config, NULL); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; - - return 0; -} - -#ifdef CONFIG_RESET_PHY_R -void mv_phy_88e1116_init(char *name) -{ - u16 reg; - u16 devadr; - - if (miiphy_set_current_dev(name)) - return; - - /* command to read PHY dev address */ - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { - printf("Err..%s could not read PHY dev address\n", - __func__); - return; - } - - /* - * Enable RGMII delay on Tx and Rx for CPU port - * Ref: sec 4.7.2 of chip datasheet - */ - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); - miiphy_read(name, devadr, MV88E1116_MAC_CTRL2_REG, ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); - miiphy_write(name, devadr, MV88E1116_MAC_CTRL2_REG, reg); - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); - - /* reset the phy */ - miiphy_reset(name, devadr); - - printf("88E1116 Initialized on %s\n", name); -} - -void reset_phy(void) -{ - /* configure and initialize both PHY's */ - mv_phy_88e1116_init("egiga0"); - mv_phy_88e1116_init("egiga1"); -} -#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/Marvell/dreamplug/dreamplug.h b/board/Marvell/dreamplug/dreamplug.h deleted file mode 100644 index 6f62238985b..00000000000 --- a/board/Marvell/dreamplug/dreamplug.h +++ /dev/null @@ -1,25 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2011 - * Jason Cooper - * - * Based on work by: - * Marvell Semiconductor - * Written-by: Siddarth Gore - */ - -#ifndef __DREAMPLUG_H -#define __DREAMPLUG_H - -#define DREAMPLUG_OE_LOW (~(0)) -#define DREAMPLUG_OE_HIGH (~(0)) -#define DREAMPLUG_OE_VAL_LOW 0 -#define DREAMPLUG_OE_VAL_HIGH (0xf << 16) /* 4 LED Pins high */ - -/* PHY related */ -#define MV88E1116_MAC_CTRL2_REG 21 -#define MV88E1116_PGADR_REG 22 -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) - -#endif /* __DREAMPLUG_H */ diff --git a/board/Marvell/dreamplug/kwbimage.cfg b/board/Marvell/dreamplug/kwbimage.cfg deleted file mode 100644 index f916208c192..00000000000 --- a/board/Marvell/dreamplug/kwbimage.cfg +++ /dev/null @@ -1,145 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2011 -# Jason Cooper -# -# Based on work by: -# Marvell Semiconductor -# Written-by: Siddarth Gore -# Refer doc/README.kwbimage for more details about how-to configure -# and create kirkwood boot image -# - -# Boot Media configurations -BOOT_FROM spi - -# SOC registers configuration using bootrom header extension -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed - -# Configure RGMII-0/1 interface pad voltage to 1.8V -DATA 0xFFD100e0 0x1b1b9b9b - -#Dram initalization for SINGLE x16 CL=5 @ 400MHz -DATA 0xFFD01400 0x43000c30 # DDR Configuration register -# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) -# bit23-14: zero -# bit24: 1= enable exit self refresh mode on DDR access -# bit25: 1 required -# bit29-26: zero -# bit31-30: 01 - -DATA 0xFFD01404 0x37543000 # DDR Controller Control Low -# bit 4: 0=addr/cmd in smame cycle -# bit 5: 0=clk is driven during self refresh, we don't care for APX -# bit 6: 0=use recommended falling edge of clk for addr/cmd -# bit14: 0=input buffer always powered up -# bit18: 1=cpu lock transaction enabled -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 -# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM -# bit30-28: 3 required -# bit31: 0=no additional STARTBURST delay - -DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) -# bit3-0: TRAS lsbs -# bit7-4: TRCD -# bit11- 8: TRP -# bit15-12: TWR -# bit19-16: TWTR -# bit20: TRAS msb -# bit23-21: 0x0 -# bit27-24: TRRD -# bit31-28: TRTP - -DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) -# bit6-0: TRFC -# bit8-7: TR2R -# bit10-9: TR2W -# bit12-11: TW2W -# bit31-13: zero required - -DATA 0xFFD01410 0x000000cc # DDR Address Control -# bit1-0: 01, Cs0width=x8 -# bit3-2: 10, Cs0size=1Gb -# bit5-4: 01, Cs1width=x8 -# bit7-6: 10, Cs1size=1Gb -# bit9-8: 00, Cs2width=nonexistent -# bit11-10: 00, Cs2size =nonexistent -# bit13-12: 00, Cs3width=nonexistent -# bit15-14: 00, Cs3size =nonexistent -# bit16: 0, Cs0AddrSel -# bit17: 0, Cs1AddrSel -# bit18: 0, Cs2AddrSel -# bit19: 0, Cs3AddrSel -# bit31-20: 0 required - -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control -# bit0: 0, OpenPage enabled -# bit31-1: 0 required - -DATA 0xFFD01418 0x00000000 # DDR Operation -# bit3-0: 0x0, DDR cmd -# bit31-4: 0 required - -DATA 0xFFD0141C 0x00000C52 # DDR Mode -# bit2-0: 2, BurstLen=2 required -# bit3: 0, BurstType=0 required -# bit6-4: 4, CL=5 -# bit7: 0, TestMode=0 normal -# bit8: 0, DLL reset=0 normal -# bit11-9: 6, auto-precharge write recovery ???????????? -# bit12: 0, PD must be zero -# bit31-13: 0 required - -DATA 0xFFD01420 0x00000040 # DDR Extended Mode -# bit0: 0, DDR DLL enabled -# bit1: 0, DDR drive strenght normal -# bit2: 0, DDR ODT control lsd (disabled) -# bit5-3: 000, required -# bit6: 1, DDR ODT control msb, (disabled) -# bit9-7: 000, required -# bit10: 0, differential DQS enabled -# bit11: 0, required -# bit12: 0, DDR output buffer enabled -# bit31-13: 0 required - -DATA 0xFFD01424 0x0000F17F # DDR Controller Control High -# bit2-0: 111, required -# bit3 : 1 , MBUS Burst Chop disabled -# bit6-4: 111, required -# bit7 : 0 -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz -# bit9 : 0 , no half clock cycle addition to dataout -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh -# bit15-12: 1111 required -# bit31-16: 0 required - -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) - -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 -DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size -# bit0: 1, Window enabled -# bit1: 0, Write Protect disabled -# bit3-2: 00, CS0 hit selected -# bit23-4: ones, required -# bit31-24: 0x0F, Size (i.e. 256MB) - -DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb -DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 - -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled - -DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above -# bit3-2: 01, ODT1 active NEVER! -# bit31-4: zero, required - -DATA 0xFFD0149C 0x0000E803 # CPU ODT Control -DATA 0xFFD01480 0x00000001 # DDR Initialization Control -#bit0=1, enable DDR init upon this register write - -# End of Header extension -DATA 0x0 0x0 diff --git a/configs/dreamplug_defconfig b/configs/dreamplug_defconfig deleted file mode 100644 index 76c768006d3..00000000000 --- a/configs/dreamplug_defconfig +++ /dev/null @@ -1,40 +0,0 @@ -CONFIG_ARM=y -CONFIG_KIRKWOOD=y -CONFIG_SYS_TEXT_BASE=0x600000 -CONFIG_TARGET_DREAMPLUG=y -CONFIG_IDENT_STRING="\nMarvell-DreamPlug" -CONFIG_NR_DRAM_BANKS=2 -# CONFIG_SYS_MALLOC_F is not set -CONFIG_BOOTDELAY=3 -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_HUSH_PARSER=y -# CONFIG_CMD_FLASH is not set -CONFIG_CMD_IDE=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_EXT4=y -CONFIG_CMD_FAT=y -CONFIG_ISO_PARTITION=y -CONFIG_OF_CONTROL=y -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dreamplug" -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_DM=y -CONFIG_MVSATA_IDE=y -# CONFIG_MMC is not set -CONFIG_SPI_FLASH=y -CONFIG_SPI_FLASH_MACRONIX=y -CONFIG_MVGBE=y -CONFIG_MII=y -CONFIG_DM_RTC=y -CONFIG_RTC_MV=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_KIRKWOOD_SPI=y -CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y -CONFIG_USB_STORAGE=y diff --git a/include/configs/dreamplug.h b/include/configs/dreamplug.h deleted file mode 100644 index 1c94bf9fa1b..00000000000 --- a/include/configs/dreamplug.h +++ /dev/null @@ -1,83 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2011 - * Jason Cooper - * - * Based on work by: - * Marvell Semiconductor - * Written-by: Siddarth Gore - */ - -#ifndef _CONFIG_DREAMPLUG_H -#define _CONFIG_DREAMPLUG_H - -/* - * High Level Configuration Options (easy to change) - */ -#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ -#define CONFIG_MACH_TYPE MACH_TYPE_DREAMPLUG - -/* - * Commands configuration - */ - -/* - * mv-plug-common.h should be defined after CMD configs since it used them - * to enable certain macros - */ -#include "mv-plug-common.h" - -/* - * Environment variables configurations - */ -#ifdef CONFIG_SPI_FLASH -#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64k */ -#endif - -#ifdef CONFIG_CMD_SF -#define CONFIG_HARD_SPI 1 -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 50000000 /* 50 MHz */ -#endif - -/* - * max 4k env size is enough, but in case of nand - * it has to be rounded to sector size - */ -#define CONFIG_ENV_SIZE 0x1000 /* 4k */ -#define CONFIG_ENV_ADDR 0x100000 -#define CONFIG_ENV_OFFSET 0x100000 /* env starts here */ - -/* - * Default environment variables - */ -#define CONFIG_BOOTCOMMAND "setenv ethact egiga0; " \ - "${x_bootcmd_ethernet}; setenv ethact egiga1; " \ - "${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; "\ - "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ - "bootm 0x6400000;" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "x_bootcmd_ethernet=ping 192.168.2.1\0" \ - "x_bootcmd_usb=usb start\0" \ - "x_bootcmd_kernel=fatload usb 0 0x6400000 uImage\0" \ - "x_bootargs=console=ttyS0,115200\0" \ - "x_bootargs_root=root=/dev/sda2 rootdelay=10\0" - -/* - * Ethernet Driver configuration - */ -#ifdef CONFIG_CMD_NET -#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ -#define CONFIG_PHY_BASE_ADR 0 -#endif /* CONFIG_CMD_NET */ - -/* - * SATA Driver configuration - */ -#ifdef CONFIG_MVSATA_IDE -#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET -#endif /*CONFIG_MVSATA_IDE*/ - -#endif /* _CONFIG_DREAMPLUG_H */ -- 2.19.1.1215.g8438c0b245-goog