All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH shawn/for-next v4 1/2] dt-bindings: arm: Add Y Soft IOTA Draco, Hydra and Ursa boards
@ 2019-01-15 14:22 ` Vokáč Michal
  0 siblings, 0 replies; 13+ messages in thread
From: Vokáč Michal @ 2019-01-15 14:22 UTC (permalink / raw)
  To: Shawn Guo
  Cc: Rob Herring, Fabio Estevam, linux-arm-kernel, linux-kernel,
	devicetree, Andrew Lunn, Vokáč Michal

These are i.MX6DualLite/Solo based single board computers used
in various Y Soft products.

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
---
Changes since v2:
 - New patch

 Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index a4d625d..b3908a0 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -94,6 +94,9 @@ properties:
               - fsl,imx6dl-sabresd        # i.MX6 DualLite SABRE Smart Device Board
               - technologic,imx6dl-ts4900
               - technologic,imx6dl-ts7970
+              - ysoft,imx6dl-yapp4-draco  # i.MX6 DualLite Y Soft IOTA Draco board
+              - ysoft,imx6dl-yapp4-hydra  # i.MX6 DualLite Y Soft IOTA Hydra board
+              - ysoft,imx6dl-yapp4-ursa   # i.MX6 Solo Y Soft IOTA Ursa board
           - const: fsl,imx6dl
 
       - description: i.MX6SL based Boards
-- 
2.1.4


^ permalink raw reply related	[flat|nested] 13+ messages in thread
* [PATCH shawn/for-next v4 1/2] dt-bindings: arm: Add Y Soft IOTA Draco, Hydra and Ursa boards
@ 2019-01-15 14:22 ` Vokáč Michal
  0 siblings, 0 replies; 13+ messages in thread
From: Vokáč Michal @ 2019-01-15 14:22 UTC (permalink / raw)
  To: Shawn Guo
  Cc: devicetree, Vokáč Michal, Andrew Lunn, linux-kernel,
	Rob Herring, Fabio Estevam, linux-arm-kernel

These are i.MX6DualLite/Solo based single board computers used
in various Y Soft products.

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
---
Changes since v2:
 - New patch

 Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index a4d625d..b3908a0 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -94,6 +94,9 @@ properties:
               - fsl,imx6dl-sabresd        # i.MX6 DualLite SABRE Smart Device Board
               - technologic,imx6dl-ts4900
               - technologic,imx6dl-ts7970
+              - ysoft,imx6dl-yapp4-draco  # i.MX6 DualLite Y Soft IOTA Draco board
+              - ysoft,imx6dl-yapp4-hydra  # i.MX6 DualLite Y Soft IOTA Hydra board
+              - ysoft,imx6dl-yapp4-ursa   # i.MX6 Solo Y Soft IOTA Ursa board
           - const: fsl,imx6dl
 
       - description: i.MX6SL based Boards
-- 
2.1.4

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 13+ messages in thread
* [PATCH shawn/for-next v4 2/2] ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards
  2019-01-15 14:22 ` Vokáč Michal
@ 2019-01-15 14:22   ` Vokáč Michal
  -1 siblings, 0 replies; 13+ messages in thread
From: Vokáč Michal @ 2019-01-15 14:22 UTC (permalink / raw)
  To: Shawn Guo
  Cc: Rob Herring, Fabio Estevam, linux-arm-kernel, linux-kernel,
	devicetree, Andrew Lunn, Vokáč Michal

These are i.MX6S/DL based SBCs embedded in various Y Soft products.
All share the same board design but have slightly different HW
configuration.

Ursa
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 1x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)

Draco
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 2x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)

Hydra
- i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
- I2C OLED display, capacitive matrix keys
- 2x Eth (QCA8334 switch)
- USB OTG
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)
- HDMI
- miniPCIe slot

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
---
Changes since v3:
 - Do not abbreviate regulator word in node names. (Shawn)
 - Sort fixed regulator nodes alphabetically.
 - Sort pmic regulator childe nodes alphabetically.
 - Use newline between properties and child node in switch node. (Shawn)
 - Sort i2c bus child nodes in order of unit-address. (Shawn)
 - Rename PWM pinctl label to be consistent with node name. (Shawn)

Changes since v2:
 - Remove cpus {/delete-node/ cpu@1;}; node from i.MX6Solo based board. (Fabio)
 - Use "device_type = "memory";" in memory nodes. (Fabio)
 - Use GPIO_ACTIVE_LOW for fec phy-reset-gpios. (Fabio)
 - Use "-" in node names. (Rob)
 - Remove label from led-controller node. (Rob)
 
Changes since v1:
 - Enable HDMI on Hydra board.
 - Move regulators to the root node and remove simple-bus property. (Rob)
 - Remove reg and unit-address property from regulators. (Rob)
 - Use correct names for led-controller and pmic node. (Rob)
 - Use wakeup-source instead of deprecated enable-sdio-wakeup. (Shawn)

 arch/arm/boot/dts/Makefile                 |   3 +
 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 595 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6dl-yapp4-draco.dts   |  58 +++
 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts   |  50 +++
 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts    |  54 +++
 5 files changed, 760 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
 create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-draco.dts
 create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
 create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bd40148..c0a9b89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -445,6 +445,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-wandboard.dtb \
 	imx6dl-wandboard-revb1.dtb \
 	imx6dl-wandboard-revd1.dtb \
+	imx6dl-yapp4-draco.dtb \
+	imx6dl-yapp4-hydra.dtb \
+	imx6dl-yapp4-ursa.dtb \
 	imx6q-apalis-eval.dtb \
 	imx6q-apalis-ixora.dtb \
 	imx6q-apalis-ixora-v1.1.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
new file mode 100644
index 0000000..b715ab0
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
@@ -0,0 +1,595 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 32 64 128 255>;
+		default-brightness-level = <32>;
+		num-interpolated-steps = <8>;
+		power-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	lcd_display: display {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel: panel {
+		compatible = "dataimage,scf0700c48ggu18";
+		power-supply = <&sw2_reg>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_pcie: regulator-pcie {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcie_reg>;
+		regulator-name = "MPCIE_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "okay";
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <20>;
+	phy-supply = <&sw2_reg>;
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy_port2: phy@1 {
+			reg = <1>;
+		};
+
+		phy_port3: phy@2 {
+			reg = <2>;
+		};
+
+		switch@0 {
+			compatible = "qca,qca8334";
+			reg = <0>;
+
+			switch_ports: ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethphy0: port@0 {
+					reg = <0>;
+					label = "cpu";
+					phy-mode = "rgmii";
+					ethernet = <&fec>;
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "eth2";
+					phy-handle = <&phy_port2>;
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "eth1";
+					phy-handle = <&phy_port3>;
+				};
+			};
+		};
+	};
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi_cec>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "disabled";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "fsl,pfuze200";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x8>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vsnvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	leds: led-controller@30 {
+		compatible = "ti,lp5562";
+		reg = <0x30>;
+		clock-mode = /bits/ 8 <1>;
+		status = "disabled";
+
+		chan0 {
+			chan-name = "R";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+		};
+
+		chan1 {
+			chan-name = "G";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+		};
+
+		chan2 {
+			chan-name = "B";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+		};
+
+		chan3 {
+			chan-name = "W";
+			led-cur = /bits/ 8 <0x0>;
+			max-cur = /bits/ 8 <0x0>;
+		};
+	};
+
+	eeprom@57 {
+		compatible = "atmel,24c128";
+		reg = <0x57>;
+		pagesize = <64>;
+		status = "okay";
+	};
+
+	touchscreen: touchscreen@5c {
+		compatible = "pixcir,pixcir_tangoc";
+		reg = <0x5c>;
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+		reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		status = "disabled";
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "disabled";
+
+	oled: oled@3d {
+		compatible = "solomon,ssd1305fb-i2c";
+		reg = <0x3d>;
+		solomon,height = <64>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,prechargep2 = <15>;
+		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	gpio_oled: gpio@41 {
+		compatible = "nxp,pca9536";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x41>;
+		vcc-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b020
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b020
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b020
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b020
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b020
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b020
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b020
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b020
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b020
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b020
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b020
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b020
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b020
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b020
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b010
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x1b010
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b098
+		>;
+	};
+
+	pinctrl_hdmi_cec: hdmicecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE	0x1b898
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b899
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL	0x4001b899
+			MX6QDL_PAD_GPIO_6__I2C3_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b098
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b098
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b098
+		>;
+	};
+
+	pinctrl_pcie_reg: pciereggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19	0x1b098
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13	0x1b098
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x8
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05	0x1b098
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b098
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0a8
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0a8
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__USB_H1_OC	0x1b098
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1-vbus {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x98
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x1b098
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b098
+		>;
+	};
+
+	pinctrl_usbotg_vbus: usbotg-vbus {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x98
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22	0x1b018
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08	0x1b018
+			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0	0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1	0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2	0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD	0x1f069
+			MX6QDL_PAD_SD4_CLK__SD4_CLK	0x10069
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0	0x17069
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1	0x17069
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2	0x17069
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3	0x17069
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4	0x17069
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5	0x17069
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6	0x17069
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7	0x17069
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__WDOG2_B	0x1b0b0
+		>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
+	vpcie-supply = <&reg_pcie>;
+	status = "disabled";
+};
+
+&pwm1 {
+	#pwm-cells = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "disabled";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+	status = "okay";
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <109>;
+	status = "disabled";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <4>;
+	cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&sw2_reg>;
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	vmmc-supply = <&sw2_reg>;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-draco.dts b/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
new file mode 100644
index 0000000..a38c407
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Draco i.MX6Solo board";
+	compatible = "ysoft,imx6dl-yapp4-draco", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcd_display {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&panel {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchscreen {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
+
+&usdhc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts b/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
new file mode 100644
index 0000000..f979270
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Hydra i.MX6DualLite board";
+	compatible = "ysoft,imx6dl-yapp4-hydra", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x80000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+};
+
+&reg_pcie {
+	status = "okay";
+};
+
+&usdhc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts b/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
new file mode 100644
index 0000000..0d594e4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Ursa i.MX6Solo board";
+	compatible = "ysoft,imx6dl-yapp4-ursa", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcd_display {
+	status = "okay";
+};
+
+&panel {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&switch_ports {
+	/delete-node/ port@2;
+};
+
+&touchscreen {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
-- 
2.1.4


^ permalink raw reply related	[flat|nested] 13+ messages in thread
* [PATCH shawn/for-next v4 2/2] ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards
@ 2019-01-15 14:22   ` Vokáč Michal
  0 siblings, 0 replies; 13+ messages in thread
From: Vokáč Michal @ 2019-01-15 14:22 UTC (permalink / raw)
  To: Shawn Guo
  Cc: devicetree, Vokáč Michal, Andrew Lunn, linux-kernel,
	Rob Herring, Fabio Estevam, linux-arm-kernel

These are i.MX6S/DL based SBCs embedded in various Y Soft products.
All share the same board design but have slightly different HW
configuration.

Ursa
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 1x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)

Draco
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 2x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)

Hydra
- i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
- I2C OLED display, capacitive matrix keys
- 2x Eth (QCA8334 switch)
- USB OTG
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)
- HDMI
- miniPCIe slot

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
---
Changes since v3:
 - Do not abbreviate regulator word in node names. (Shawn)
 - Sort fixed regulator nodes alphabetically.
 - Sort pmic regulator childe nodes alphabetically.
 - Use newline between properties and child node in switch node. (Shawn)
 - Sort i2c bus child nodes in order of unit-address. (Shawn)
 - Rename PWM pinctl label to be consistent with node name. (Shawn)

Changes since v2:
 - Remove cpus {/delete-node/ cpu@1;}; node from i.MX6Solo based board. (Fabio)
 - Use "device_type = "memory";" in memory nodes. (Fabio)
 - Use GPIO_ACTIVE_LOW for fec phy-reset-gpios. (Fabio)
 - Use "-" in node names. (Rob)
 - Remove label from led-controller node. (Rob)
 
Changes since v1:
 - Enable HDMI on Hydra board.
 - Move regulators to the root node and remove simple-bus property. (Rob)
 - Remove reg and unit-address property from regulators. (Rob)
 - Use correct names for led-controller and pmic node. (Rob)
 - Use wakeup-source instead of deprecated enable-sdio-wakeup. (Shawn)

 arch/arm/boot/dts/Makefile                 |   3 +
 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 595 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6dl-yapp4-draco.dts   |  58 +++
 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts   |  50 +++
 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts    |  54 +++
 5 files changed, 760 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
 create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-draco.dts
 create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
 create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bd40148..c0a9b89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -445,6 +445,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-wandboard.dtb \
 	imx6dl-wandboard-revb1.dtb \
 	imx6dl-wandboard-revd1.dtb \
+	imx6dl-yapp4-draco.dtb \
+	imx6dl-yapp4-hydra.dtb \
+	imx6dl-yapp4-ursa.dtb \
 	imx6q-apalis-eval.dtb \
 	imx6q-apalis-ixora.dtb \
 	imx6q-apalis-ixora-v1.1.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
new file mode 100644
index 0000000..b715ab0
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
@@ -0,0 +1,595 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 32 64 128 255>;
+		default-brightness-level = <32>;
+		num-interpolated-steps = <8>;
+		power-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	lcd_display: display {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel: panel {
+		compatible = "dataimage,scf0700c48ggu18";
+		power-supply = <&sw2_reg>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_pcie: regulator-pcie {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcie_reg>;
+		regulator-name = "MPCIE_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "okay";
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <20>;
+	phy-supply = <&sw2_reg>;
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy_port2: phy@1 {
+			reg = <1>;
+		};
+
+		phy_port3: phy@2 {
+			reg = <2>;
+		};
+
+		switch@0 {
+			compatible = "qca,qca8334";
+			reg = <0>;
+
+			switch_ports: ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethphy0: port@0 {
+					reg = <0>;
+					label = "cpu";
+					phy-mode = "rgmii";
+					ethernet = <&fec>;
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "eth2";
+					phy-handle = <&phy_port2>;
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "eth1";
+					phy-handle = <&phy_port3>;
+				};
+			};
+		};
+	};
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi_cec>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "disabled";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "fsl,pfuze200";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x8>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vsnvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	leds: led-controller@30 {
+		compatible = "ti,lp5562";
+		reg = <0x30>;
+		clock-mode = /bits/ 8 <1>;
+		status = "disabled";
+
+		chan0 {
+			chan-name = "R";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+		};
+
+		chan1 {
+			chan-name = "G";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+		};
+
+		chan2 {
+			chan-name = "B";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+		};
+
+		chan3 {
+			chan-name = "W";
+			led-cur = /bits/ 8 <0x0>;
+			max-cur = /bits/ 8 <0x0>;
+		};
+	};
+
+	eeprom@57 {
+		compatible = "atmel,24c128";
+		reg = <0x57>;
+		pagesize = <64>;
+		status = "okay";
+	};
+
+	touchscreen: touchscreen@5c {
+		compatible = "pixcir,pixcir_tangoc";
+		reg = <0x5c>;
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+		reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		status = "disabled";
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "disabled";
+
+	oled: oled@3d {
+		compatible = "solomon,ssd1305fb-i2c";
+		reg = <0x3d>;
+		solomon,height = <64>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,prechargep2 = <15>;
+		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	gpio_oled: gpio@41 {
+		compatible = "nxp,pca9536";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x41>;
+		vcc-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b020
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b020
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b020
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b020
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b020
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b020
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b020
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b020
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b020
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b020
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b020
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b020
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b020
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b020
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b010
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x1b010
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b098
+		>;
+	};
+
+	pinctrl_hdmi_cec: hdmicecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE	0x1b898
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b899
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL	0x4001b899
+			MX6QDL_PAD_GPIO_6__I2C3_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b098
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b098
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b098
+		>;
+	};
+
+	pinctrl_pcie_reg: pciereggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19	0x1b098
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13	0x1b098
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x8
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05	0x1b098
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b098
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0a8
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0a8
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__USB_H1_OC	0x1b098
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1-vbus {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x98
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x1b098
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b098
+		>;
+	};
+
+	pinctrl_usbotg_vbus: usbotg-vbus {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x98
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22	0x1b018
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08	0x1b018
+			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0	0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1	0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2	0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD	0x1f069
+			MX6QDL_PAD_SD4_CLK__SD4_CLK	0x10069
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0	0x17069
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1	0x17069
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2	0x17069
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3	0x17069
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4	0x17069
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5	0x17069
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6	0x17069
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7	0x17069
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__WDOG2_B	0x1b0b0
+		>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
+	vpcie-supply = <&reg_pcie>;
+	status = "disabled";
+};
+
+&pwm1 {
+	#pwm-cells = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "disabled";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+	status = "okay";
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <109>;
+	status = "disabled";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <4>;
+	cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&sw2_reg>;
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	vmmc-supply = <&sw2_reg>;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-draco.dts b/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
new file mode 100644
index 0000000..a38c407
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Draco i.MX6Solo board";
+	compatible = "ysoft,imx6dl-yapp4-draco", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcd_display {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&panel {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchscreen {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
+
+&usdhc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts b/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
new file mode 100644
index 0000000..f979270
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Hydra i.MX6DualLite board";
+	compatible = "ysoft,imx6dl-yapp4-hydra", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x80000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+};
+
+&reg_pcie {
+	status = "okay";
+};
+
+&usdhc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts b/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
new file mode 100644
index 0000000..0d594e4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Ursa i.MX6Solo board";
+	compatible = "ysoft,imx6dl-yapp4-ursa", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcd_display {
+	status = "okay";
+};
+
+&panel {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&switch_ports {
+	/delete-node/ port@2;
+};
+
+&touchscreen {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
-- 
2.1.4

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 13+ messages in thread
* Re: [PATCH shawn/for-next v4 1/2] dt-bindings: arm: Add Y Soft IOTA Draco, Hydra and Ursa boards
  2019-01-15 14:22 ` Vokáč Michal
  (?)
@ 2019-01-15 20:09   ` Rob Herring
  -1 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2019-01-15 20:09 UTC (permalink / raw)
  To: Vokáč Michal
  Cc: Shawn Guo, Fabio Estevam, linux-arm-kernel, linux-kernel,
	devicetree, Andrew Lunn, Vokáč Michal

On Tue, 15 Jan 2019 14:22:44 +0000, =?utf-8?B?Vm9rw6HEjSBNaWNoYWw=?= wrote:
> These are i.MX6DualLite/Solo based single board computers used
> in various Y Soft products.
> 
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
> ---
> Changes since v2:
>  - New patch
> 
>  Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH shawn/for-next v4 1/2] dt-bindings: arm: Add Y Soft IOTA Draco, Hydra and Ursa boards
@ 2019-01-15 20:09   ` Rob Herring
  0 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2019-01-15 20:09 UTC (permalink / raw)
  Cc: Shawn Guo, Fabio Estevam, linux-arm-kernel, linux-kernel,
	devicetree, Andrew Lunn, Vokáč Michal

On Tue, 15 Jan 2019 14:22:44 +0000, =?utf-8?B?Vm9rw6HEjSBNaWNoYWw=?= wrote:
> These are i.MX6DualLite/Solo based single board computers used
> in various Y Soft products.
> 
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
> ---
> Changes since v2:
>  - New patch
> 
>  Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH shawn/for-next v4 1/2] dt-bindings: arm: Add Y Soft IOTA Draco, Hydra and Ursa boards
@ 2019-01-15 20:09   ` Rob Herring
  0 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2019-01-15 20:09 UTC (permalink / raw)
  To: Vokáč Michal
  Cc: devicetree, Vokáč Michal, Andrew Lunn, linux-kernel,
	Fabio Estevam, Shawn Guo, linux-arm-kernel

On Tue, 15 Jan 2019 14:22:44 +0000, =?utf-8?B?Vm9rw6HEjSBNaWNoYWw=?= wrote:
> These are i.MX6DualLite/Solo based single board computers used
> in various Y Soft products.
> 
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
> ---
> Changes since v2:
>  - New patch
> 
>  Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH shawn/for-next v4 2/2] ARM: dts: imx: Add Y Soft IOTA Draco,  Hydra and Ursa boards
  2019-01-15 14:22   ` Vokáč Michal
  (?)
@ 2019-01-15 20:12     ` Rob Herring
  -1 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2019-01-15 20:12 UTC (permalink / raw)
  To: Vokáč Michal
  Cc: Shawn Guo, Fabio Estevam, linux-arm-kernel, linux-kernel,
	devicetree, Andrew Lunn, Vokáč Michal

On Tue, 15 Jan 2019 14:22:45 +0000, =?utf-8?B?Vm9rw6HEjSBNaWNoYWw=?= wrote:
> These are i.MX6S/DL based SBCs embedded in various Y Soft products.
> All share the same board design but have slightly different HW
> configuration.
> 
> Ursa
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 1x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
> 
> Draco
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
> 
> Hydra
> - i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
> - I2C OLED display, capacitive matrix keys
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
> - HDMI
> - miniPCIe slot
> 
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
> ---
> Changes since v3:
>  - Do not abbreviate regulator word in node names. (Shawn)
>  - Sort fixed regulator nodes alphabetically.
>  - Sort pmic regulator childe nodes alphabetically.
>  - Use newline between properties and child node in switch node. (Shawn)
>  - Sort i2c bus child nodes in order of unit-address. (Shawn)
>  - Rename PWM pinctl label to be consistent with node name. (Shawn)
> 
> Changes since v2:
>  - Remove cpus {/delete-node/ cpu@1;}; node from i.MX6Solo based board. (Fabio)
>  - Use "device_type = "memory";" in memory nodes. (Fabio)
>  - Use GPIO_ACTIVE_LOW for fec phy-reset-gpios. (Fabio)
>  - Use "-" in node names. (Rob)
>  - Remove label from led-controller node. (Rob)
>  
> Changes since v1:
>  - Enable HDMI on Hydra board.
>  - Move regulators to the root node and remove simple-bus property. (Rob)
>  - Remove reg and unit-address property from regulators. (Rob)
>  - Use correct names for led-controller and pmic node. (Rob)
>  - Use wakeup-source instead of deprecated enable-sdio-wakeup. (Shawn)
> 
>  arch/arm/boot/dts/Makefile                 |   3 +
>  arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 595 +++++++++++++++++++++++++++++
>  arch/arm/boot/dts/imx6dl-yapp4-draco.dts   |  58 +++
>  arch/arm/boot/dts/imx6dl-yapp4-hydra.dts   |  50 +++
>  arch/arm/boot/dts/imx6dl-yapp4-ursa.dts    |  54 +++
>  5 files changed, 760 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-draco.dts
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
> 

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH shawn/for-next v4 2/2] ARM: dts: imx: Add Y Soft IOTA Draco,  Hydra and Ursa boards
@ 2019-01-15 20:12     ` Rob Herring
  0 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2019-01-15 20:12 UTC (permalink / raw)
  Cc: Shawn Guo, Fabio Estevam, linux-arm-kernel, linux-kernel,
	devicetree, Andrew Lunn, Vokáč Michal

On Tue, 15 Jan 2019 14:22:45 +0000, =?utf-8?B?Vm9rw6HEjSBNaWNoYWw=?= wrote:
> These are i.MX6S/DL based SBCs embedded in various Y Soft products.
> All share the same board design but have slightly different HW
> configuration.
> 
> Ursa
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 1x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
> 
> Draco
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
> 
> Hydra
> - i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
> - I2C OLED display, capacitive matrix keys
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
> - HDMI
> - miniPCIe slot
> 
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
> ---
> Changes since v3:
>  - Do not abbreviate regulator word in node names. (Shawn)
>  - Sort fixed regulator nodes alphabetically.
>  - Sort pmic regulator childe nodes alphabetically.
>  - Use newline between properties and child node in switch node. (Shawn)
>  - Sort i2c bus child nodes in order of unit-address. (Shawn)
>  - Rename PWM pinctl label to be consistent with node name. (Shawn)
> 
> Changes since v2:
>  - Remove cpus {/delete-node/ cpu@1;}; node from i.MX6Solo based board. (Fabio)
>  - Use "device_type = "memory";" in memory nodes. (Fabio)
>  - Use GPIO_ACTIVE_LOW for fec phy-reset-gpios. (Fabio)
>  - Use "-" in node names. (Rob)
>  - Remove label from led-controller node. (Rob)
>  
> Changes since v1:
>  - Enable HDMI on Hydra board.
>  - Move regulators to the root node and remove simple-bus property. (Rob)
>  - Remove reg and unit-address property from regulators. (Rob)
>  - Use correct names for led-controller and pmic node. (Rob)
>  - Use wakeup-source instead of deprecated enable-sdio-wakeup. (Shawn)
> 
>  arch/arm/boot/dts/Makefile                 |   3 +
>  arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 595 +++++++++++++++++++++++++++++
>  arch/arm/boot/dts/imx6dl-yapp4-draco.dts   |  58 +++
>  arch/arm/boot/dts/imx6dl-yapp4-hydra.dts   |  50 +++
>  arch/arm/boot/dts/imx6dl-yapp4-ursa.dts    |  54 +++
>  5 files changed, 760 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-draco.dts
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
> 

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH shawn/for-next v4 2/2] ARM: dts: imx: Add Y Soft IOTA Draco,  Hydra and Ursa boards
@ 2019-01-15 20:12     ` Rob Herring
  0 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2019-01-15 20:12 UTC (permalink / raw)
  To: Vokáč Michal
  Cc: devicetree, Vokáč Michal, Andrew Lunn, linux-kernel,
	Fabio Estevam, Shawn Guo, linux-arm-kernel

On Tue, 15 Jan 2019 14:22:45 +0000, =?utf-8?B?Vm9rw6HEjSBNaWNoYWw=?= wrote:
> These are i.MX6S/DL based SBCs embedded in various Y Soft products.
> All share the same board design but have slightly different HW
> configuration.
> 
> Ursa
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 1x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
> 
> Draco
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
> 
> Hydra
> - i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
> - I2C OLED display, capacitive matrix keys
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
> - HDMI
> - miniPCIe slot
> 
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
> ---
> Changes since v3:
>  - Do not abbreviate regulator word in node names. (Shawn)
>  - Sort fixed regulator nodes alphabetically.
>  - Sort pmic regulator childe nodes alphabetically.
>  - Use newline between properties and child node in switch node. (Shawn)
>  - Sort i2c bus child nodes in order of unit-address. (Shawn)
>  - Rename PWM pinctl label to be consistent with node name. (Shawn)
> 
> Changes since v2:
>  - Remove cpus {/delete-node/ cpu@1;}; node from i.MX6Solo based board. (Fabio)
>  - Use "device_type = "memory";" in memory nodes. (Fabio)
>  - Use GPIO_ACTIVE_LOW for fec phy-reset-gpios. (Fabio)
>  - Use "-" in node names. (Rob)
>  - Remove label from led-controller node. (Rob)
>  
> Changes since v1:
>  - Enable HDMI on Hydra board.
>  - Move regulators to the root node and remove simple-bus property. (Rob)
>  - Remove reg and unit-address property from regulators. (Rob)
>  - Use correct names for led-controller and pmic node. (Rob)
>  - Use wakeup-source instead of deprecated enable-sdio-wakeup. (Shawn)
> 
>  arch/arm/boot/dts/Makefile                 |   3 +
>  arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 595 +++++++++++++++++++++++++++++
>  arch/arm/boot/dts/imx6dl-yapp4-draco.dts   |  58 +++
>  arch/arm/boot/dts/imx6dl-yapp4-hydra.dts   |  50 +++
>  arch/arm/boot/dts/imx6dl-yapp4-ursa.dts    |  54 +++
>  5 files changed, 760 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-draco.dts
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
>  create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH shawn/for-next v4 1/2] dt-bindings: arm: Add Y Soft IOTA Draco, Hydra and Ursa boards
  2019-01-15 14:22 ` Vokáč Michal
  (?)
@ 2019-01-16 10:48   ` Shawn Guo
  -1 siblings, 0 replies; 13+ messages in thread
From: Shawn Guo @ 2019-01-16 10:48 UTC (permalink / raw)
  To: Vokáč Michal
  Cc: devicetree, Andrew Lunn, linux-kernel, Rob Herring,
	Fabio Estevam, linux-arm-kernel

On Tue, Jan 15, 2019 at 02:22:44PM +0000, Vokáč Michal wrote:
> These are i.MX6DualLite/Solo based single board computers used
> in various Y Soft products.
> 
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>

Applied both, thanks.

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH shawn/for-next v4 1/2] dt-bindings: arm: Add Y Soft IOTA Draco, Hydra and Ursa boards
@ 2019-01-16 10:48   ` Shawn Guo
  0 siblings, 0 replies; 13+ messages in thread
From: Shawn Guo @ 2019-01-16 10:48 UTC (permalink / raw)
  To: Vokáč Michal
  Cc: devicetree, Andrew Lunn, linux-kernel, Rob Herring,
	Fabio Estevam, linux-arm-kernel

On Tue, Jan 15, 2019 at 02:22:44PM +0000, Vokáč Michal wrote:
> These are i.MX6DualLite/Solo based single board computers used
> in various Y Soft products.
> 
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>

Applied both, thanks.

^ permalink raw reply	[flat|nested] 13+ messages in thread
* Re: [PATCH shawn/for-next v4 1/2] dt-bindings: arm: Add Y Soft IOTA Draco, Hydra and Ursa boards
@ 2019-01-16 10:48   ` Shawn Guo
  0 siblings, 0 replies; 13+ messages in thread
From: Shawn Guo @ 2019-01-16 10:48 UTC (permalink / raw)
  To: Vokáč Michal
  Cc: devicetree, Andrew Lunn, linux-kernel, Rob Herring,
	Fabio Estevam, linux-arm-kernel

On Tue, Jan 15, 2019 at 02:22:44PM +0000, Vokáč Michal wrote:
> These are i.MX6DualLite/Solo based single board computers used
> in various Y Soft products.
> 
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>

Applied both, thanks.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 13+ messages in thread
end of thread, other threads:[~2019-01-16 10:49 UTC | newest]

Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-01-15 14:22 [PATCH shawn/for-next v4 1/2] dt-bindings: arm: Add Y Soft IOTA Draco, Hydra and Ursa boards Vokáč Michal
2019-01-15 14:22 ` Vokáč Michal
2019-01-15 14:22 ` [PATCH shawn/for-next v4 2/2] ARM: dts: imx: " Vokáč Michal
2019-01-15 14:22   ` Vokáč Michal
2019-01-15 20:12   ` Rob Herring
2019-01-15 20:12     ` Rob Herring
2019-01-15 20:12     ` Rob Herring
2019-01-15 20:09 ` [PATCH shawn/for-next v4 1/2] dt-bindings: arm: " Rob Herring
2019-01-15 20:09   ` Rob Herring
2019-01-15 20:09   ` Rob Herring
2019-01-16 10:48 ` Shawn Guo
2019-01-16 10:48   ` Shawn Guo
2019-01-16 10:48   ` Shawn Guo

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.