From mboxrd@z Thu Jan 1 00:00:00 1970 From: Shawn Guo Date: Thu, 17 Jan 2019 12:09:50 +0800 Subject: [U-Boot] [PATCH 1/3] poplar: sync up device tree with kernel 4.20 In-Reply-To: <20190117040952.4024-1-shawn.guo@linaro.org> References: <20190117040952.4024-1-shawn.guo@linaro.org> Message-ID: <20190117040952.4024-2-shawn.guo@linaro.org> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de It adds missing pinctrl headers, updates clock header and sync up Poplar device tree with kernel 4.20 release. Signed-off-by: Shawn Guo --- arch/arm/dts/hi3798cv200-poplar.dts | 68 ++++++-- arch/arm/dts/hi3798cv200.dtsi | 221 +++++++++++++++++++++++- arch/arm/dts/poplar-pinctrl.dtsi | 98 +++++++++++ include/dt-bindings/clock/histb-clock.h | 56 +++--- include/dt-bindings/pinctrl/hisi.h | 74 ++++++++ 5 files changed, 482 insertions(+), 35 deletions(-) create mode 100644 arch/arm/dts/poplar-pinctrl.dtsi create mode 100644 include/dt-bindings/pinctrl/hisi.h diff --git a/arch/arm/dts/hi3798cv200-poplar.dts b/arch/arm/dts/hi3798cv200-poplar.dts index 964326eae89b..d30f6eb8a5ee 100644 --- a/arch/arm/dts/hi3798cv200-poplar.dts +++ b/arch/arm/dts/hi3798cv200-poplar.dts @@ -1,14 +1,17 @@ -// SPDX-License-Identifier: GPL-2.0 /* * DTS File for HiSilicon Poplar Development Board * * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd. + * + * Released under the GPLv2 only. + * SPDX-License-Identifier: GPL-2.0 */ /dts-v1/; #include #include "hi3798cv200.dtsi" +#include "poplar-pinctrl.dtsi" / { model = "HiSilicon Poplar Development Board"; @@ -59,6 +62,33 @@ default-state = "off"; }; }; + + reg_pcie: regulator-pcie { + compatible = "regulator-fixed"; + regulator-name = "3V3_PCIE0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio6 7 0>; + enable-active-high; + }; +}; + +&ehci { + status = "okay"; +}; + +&emmc { + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins_1 &emmc_pins_2 + &emmc_pins_3 &emmc_pins_4>; + fifo-depth = <256>; + clock-frequency = <200000000>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + non-removable; + bus-width = <8>; + status = "okay"; }; &gmac1 { @@ -76,17 +106,17 @@ &gpio1 { status = "okay"; - gpio-line-names = "LS-GPIO-E", "", + gpio-line-names = "GPIO-E", "", "", "", - "", "LS-GPIO-F", - "", "LS-GPIO-J"; + "", "GPIO-F", + "", "GPIO-J"; }; &gpio2 { status = "okay"; - gpio-line-names = "LS-GPIO-H", "LS-GPIO-I", - "LS-GPIO-L", "LS-GPIO-G", - "LS-GPIO-K", "", + gpio-line-names = "GPIO-H", "GPIO-I", + "GPIO-L", "GPIO-G", + "GPIO-K", "", "", ""; }; @@ -94,15 +124,15 @@ status = "okay"; gpio-line-names = "", "", "", "", - "LS-GPIO-C", "", - "", "LS-GPIO-B"; + "GPIO-C", "", + "", "GPIO-B"; }; &gpio4 { status = "okay"; gpio-line-names = "", "", "", "", - "", "LS-GPIO-D", + "", "GPIO-D", "", ""; }; @@ -110,7 +140,7 @@ status = "okay"; gpio-line-names = "", "USER-LED-1", "USER-LED-2", "", - "", "LS-GPIO-A", + "", "GPIO-A", "", ""; }; @@ -144,6 +174,22 @@ status = "okay"; }; +&ohci { + status = "okay"; +}; + +&pcie { + reset-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; + vpcie-supply = <®_pcie>; + status = "okay"; +}; + +&sd0 { + bus-width = <4>; + cap-sd-highspeed; + status = "okay"; +}; + &spi0 { status = "okay"; label = "LS-SPI0"; diff --git a/arch/arm/dts/hi3798cv200.dtsi b/arch/arm/dts/hi3798cv200.dtsi index 8b9c5ad05a19..7c0fddd7c8cf 100644 --- a/arch/arm/dts/hi3798cv200.dtsi +++ b/arch/arm/dts/hi3798cv200.dtsi @@ -1,12 +1,16 @@ -// SPDX-License-Identifier: GPL-2.0 /* * DTS File for HiSilicon Hi3798cv200 SoC. * * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd. + * + * Released under the GPLv2 only. + * SPDX-License-Identifier: GPL-2.0 */ #include +#include #include +#include #include / { @@ -104,6 +108,113 @@ #reset-cells = <2>; }; + perictrl: peripheral-controller at 8a20000 { + compatible = "hisilicon,hi3798cv200-perictrl", "syscon", + "simple-mfd"; + reg = <0x8a20000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x8a20000 0x1000>; + + usb2_phy1: usb2-phy at 120 { + compatible = "hisilicon,hi3798cv200-usb2-phy"; + reg = <0x120 0x4>; + clocks = <&crg HISTB_USB2_PHY1_REF_CLK>; + resets = <&crg 0xbc 4>; + #address-cells = <1>; + #size-cells = <0>; + + usb2_phy1_port0: phy at 0 { + reg = <0>; + #phy-cells = <0>; + resets = <&crg 0xbc 8>; + }; + + usb2_phy1_port1: phy at 1 { + reg = <1>; + #phy-cells = <0>; + resets = <&crg 0xbc 9>; + }; + }; + + usb2_phy2: usb2-phy at 124 { + compatible = "hisilicon,hi3798cv200-usb2-phy"; + reg = <0x124 0x4>; + clocks = <&crg HISTB_USB2_PHY2_REF_CLK>; + resets = <&crg 0xbc 6>; + #address-cells = <1>; + #size-cells = <0>; + + usb2_phy2_port0: phy at 0 { + reg = <0>; + #phy-cells = <0>; + resets = <&crg 0xbc 10>; + }; + }; + + combphy0: phy at 850 { + compatible = "hisilicon,hi3798cv200-combphy"; + reg = <0x850 0x8>; + #phy-cells = <1>; + clocks = <&crg HISTB_COMBPHY0_CLK>; + resets = <&crg 0x188 4>; + assigned-clocks = <&crg HISTB_COMBPHY0_CLK>; + assigned-clock-rates = <100000000>; + hisilicon,fixed-mode = ; + }; + + combphy1: phy at 858 { + compatible = "hisilicon,hi3798cv200-combphy"; + reg = <0x858 0x8>; + #phy-cells = <1>; + clocks = <&crg HISTB_COMBPHY1_CLK>; + resets = <&crg 0x188 12>; + assigned-clocks = <&crg HISTB_COMBPHY1_CLK>; + assigned-clock-rates = <100000000>; + hisilicon,mode-select-bits = <0x0008 11 (0x3 << 11)>; + }; + }; + + pmx0: pinconf at 8a21000 { + compatible = "pinconf-single"; + reg = <0x8a21000 0x180>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <7>; + pinctrl-single,gpio-range = < + &range 0 8 2 /* GPIO 0 */ + &range 8 1 0 /* GPIO 1 */ + &range 9 4 2 + &range 13 1 0 + &range 14 1 1 + &range 15 1 0 + &range 16 5 0 /* GPIO 2 */ + &range 21 3 1 + &range 24 4 1 /* GPIO 3 */ + &range 28 2 2 + &range 86 1 1 + &range 87 1 0 + &range 30 4 2 /* GPIO 4 */ + &range 34 3 0 + &range 37 1 2 + &range 38 3 2 /* GPIO 6 */ + &range 41 5 0 + &range 46 8 1 /* GPIO 7 */ + &range 54 8 1 /* GPIO 8 */ + &range 64 7 1 /* GPIO 9 */ + &range 71 1 0 + &range 72 6 1 /* GPIO 10 */ + &range 78 1 0 + &range 79 1 1 + &range 80 6 1 /* GPIO 11 */ + &range 70 2 1 + &range 88 8 0 /* GPIO 12 */ + >; + + range: gpio-range { + #pinctrl-single,gpio-range-cells = <3>; + }; + }; + uart0: serial at 8b00000 { compatible = "arm,pl011", "arm,primecell"; reg = <0x8b00000 0x1000>; @@ -190,13 +301,30 @@ status = "disabled"; }; - emmc: mmc at 9830000 { + sd0: mmc at 9820000 { compatible = "snps,dw-mshc"; + reg = <0x9820000 0x10000>; + interrupts = ; + clocks = <&crg HISTB_SDIO0_CIU_CLK>, + <&crg HISTB_SDIO0_BIU_CLK>; + clock-names = "ciu", "biu"; + resets = <&crg 0x9c 4>; + reset-names = "reset"; + status = "disabled"; + }; + + emmc: mmc at 9830000 { + compatible = "hisilicon,hi3798cv200-dw-mshc"; reg = <0x9830000 0x10000>; interrupts = ; clocks = <&crg HISTB_MMC_CIU_CLK>, - <&crg HISTB_MMC_BIU_CLK>; - clock-names = "ciu", "biu"; + <&crg HISTB_MMC_BIU_CLK>, + <&crg HISTB_MMC_SAMPLE_CLK>, + <&crg HISTB_MMC_DRV_CLK>; + clock-names = "ciu", "biu", "ciu-sample", "ciu-drive"; + resets = <&crg 0xa0 4>; + reset-names = "reset"; + status = "disabled"; }; gpio0: gpio at 8b20000 { @@ -207,6 +335,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 0 8>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -220,6 +349,13 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = < + &pmx0 0 8 1 + &pmx0 1 9 4 + &pmx0 5 13 1 + &pmx0 6 14 1 + &pmx0 7 15 1 + >; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -233,6 +369,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 16 5 &pmx0 5 21 3>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -246,6 +383,12 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = < + &pmx0 0 24 4 + &pmx0 4 28 2 + &pmx0 6 86 1 + &pmx0 7 87 1 + >; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -259,6 +402,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 30 4 &pmx0 4 34 3 &pmx0 7 37 1>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -285,6 +429,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 38 3 &pmx0 0 41 5>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -298,6 +443,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 46 8>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -311,6 +457,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 54 8>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -324,6 +471,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 64 7 &pmx0 71 1>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -337,6 +485,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 72 6 &pmx0 6 78 1 &pmx0 7 79 1>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -350,6 +499,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 80 6 &pmx0 6 70 2>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -363,6 +513,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&pmx0 0 88 8>; clocks = <&crg HISTB_APB_CLK>; clock-names = "apb_pclk"; status = "disabled"; @@ -405,5 +556,67 @@ clocks = <&sysctrl HISTB_IR_CLK>; status = "disabled"; }; + + pcie: pcie at 9860000 { + compatible = "hisilicon,hi3798cv200-pcie"; + reg = <0x9860000 0x1000>, + <0x0 0x2000>, + <0x2000000 0x01000000>; + reg-names = "control", "rc-dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0 15>; + num-lanes = <1>; + ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000 + 0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>; + interrupts = ; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 131 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_PCIE_AUX_CLK>, + <&crg HISTB_PCIE_PIPE_CLK>, + <&crg HISTB_PCIE_SYS_CLK>, + <&crg HISTB_PCIE_BUS_CLK>; + clock-names = "aux", "pipe", "sys", "bus"; + resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>; + reset-names = "soft", "sys", "bus"; + phys = <&combphy1 PHY_TYPE_PCIE>; + phy-names = "phy"; + status = "disabled"; + }; + + ohci: ohci at 9880000 { + compatible = "generic-ohci"; + reg = <0x9880000 0x10000>; + interrupts = ; + clocks = <&crg HISTB_USB2_BUS_CLK>, + <&crg HISTB_USB2_12M_CLK>, + <&crg HISTB_USB2_48M_CLK>; + clock-names = "bus", "clk12", "clk48"; + resets = <&crg 0xb8 12>; + reset-names = "bus"; + phys = <&usb2_phy1_port0>; + phy-names = "usb"; + status = "disabled"; + }; + + ehci: ehci at 9890000 { + compatible = "generic-ehci"; + reg = <0x9890000 0x10000>; + interrupts = ; + clocks = <&crg HISTB_USB2_BUS_CLK>, + <&crg HISTB_USB2_PHY_CLK>, + <&crg HISTB_USB2_UTMI_CLK>; + clock-names = "bus", "phy", "utmi"; + resets = <&crg 0xb8 12>, + <&crg 0xb8 16>, + <&crg 0xb8 13>; + reset-names = "bus", "phy", "utmi"; + phys = <&usb2_phy1_port0>; + phy-names = "usb"; + status = "disabled"; + }; }; }; diff --git a/arch/arm/dts/poplar-pinctrl.dtsi b/arch/arm/dts/poplar-pinctrl.dtsi new file mode 100644 index 000000000000..7bb19e4b084a --- /dev/null +++ b/arch/arm/dts/poplar-pinctrl.dtsi @@ -0,0 +1,98 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Pinctrl dts file for HiSilicon Poplar board + * + * Copyright (c) 2016-2018 HiSilicon Technologies Co., Ltd. + */ + +#include + +/* value, enable bits, disable bits, mask */ +#define PINCTRL_PULLDOWN(value, enable, disable, mask) \ + (value << 13) (enable << 13) (disable << 13) (mask << 13) +#define PINCTRL_PULLUP(value, enable, disable, mask) \ + (value << 12) (enable << 12) (disable << 12) (mask << 12) +#define PINCTRL_SLEW_RATE(value, mask) (value << 8) (mask << 8) +#define PINCTRL_DRV_STRENGTH(value, mask) (value << 4) (mask << 4) + +&pmx0 { + emmc_pins_1: emmc-pins-1 { + pinctrl-single,pins = < + 0x000 MUX_M2 + 0x004 MUX_M2 + 0x008 MUX_M2 + 0x00c MUX_M2 + 0x010 MUX_M2 + 0x014 MUX_M2 + 0x018 MUX_M2 + 0x01c MUX_M2 + 0x024 MUX_M2 + >; + pinctrl-single,bias-pulldown = < + PINCTRL_PULLDOWN(0, 1, 0, 1) + >; + pinctrl-single,bias-pullup = < + PINCTRL_PULLUP(0, 1, 0, 1) + >; + pinctrl-single,slew-rate = < + PINCTRL_SLEW_RATE(1, 1) + >; + pinctrl-single,drive-strength = < + PINCTRL_DRV_STRENGTH(0xb, 0xf) + >; + }; + + emmc_pins_2: emmc-pins-2 { + pinctrl-single,pins = < + 0x028 MUX_M2 + >; + pinctrl-single,bias-pulldown = < + PINCTRL_PULLDOWN(0, 1, 0, 1) + >; + pinctrl-single,bias-pullup = < + PINCTRL_PULLUP(0, 1, 0, 1) + >; + pinctrl-single,slew-rate = < + PINCTRL_SLEW_RATE(1, 1) + >; + pinctrl-single,drive-strength = < + PINCTRL_DRV_STRENGTH(0x9, 0xf) + >; + }; + + emmc_pins_3: emmc-pins-3 { + pinctrl-single,pins = < + 0x02c MUX_M2 + >; + pinctrl-single,bias-pulldown = < + PINCTRL_PULLDOWN(0, 1, 0, 1) + >; + pinctrl-single,bias-pullup = < + PINCTRL_PULLUP(0, 1, 0, 1) + >; + pinctrl-single,slew-rate = < + PINCTRL_SLEW_RATE(1, 1) + >; + pinctrl-single,drive-strength = < + PINCTRL_DRV_STRENGTH(3, 3) + >; + }; + + emmc_pins_4: emmc-pins-4 { + pinctrl-single,pins = < + 0x030 MUX_M2 + >; + pinctrl-single,bias-pulldown = < + PINCTRL_PULLDOWN(1, 1, 0, 1) + >; + pinctrl-single,bias-pullup = < + PINCTRL_PULLUP(0, 1, 0, 1) + >; + pinctrl-single,slew-rate = < + PINCTRL_SLEW_RATE(1, 1) + >; + pinctrl-single,drive-strength = < + PINCTRL_DRV_STRENGTH(3, 3) + >; + }; +}; diff --git a/include/dt-bindings/clock/histb-clock.h b/include/dt-bindings/clock/histb-clock.h index 181c0f070f7c..136de24733be 100644 --- a/include/dt-bindings/clock/histb-clock.h +++ b/include/dt-bindings/clock/histb-clock.h @@ -22,18 +22,18 @@ #define HISTB_OSC_CLK 0 #define HISTB_APB_CLK 1 #define HISTB_AHB_CLK 2 -#define HISTB_UART1_CLK 3 -#define HISTB_UART2_CLK 4 -#define HISTB_UART3_CLK 5 -#define HISTB_I2C0_CLK 6 -#define HISTB_I2C1_CLK 7 -#define HISTB_I2C2_CLK 8 -#define HISTB_I2C3_CLK 9 -#define HISTB_I2C4_CLK 10 -#define HISTB_I2C5_CLK 11 -#define HISTB_SPI0_CLK 12 -#define HISTB_SPI1_CLK 13 -#define HISTB_SPI2_CLK 14 +#define HISTB_UART1_CLK 3 +#define HISTB_UART2_CLK 4 +#define HISTB_UART3_CLK 5 +#define HISTB_I2C0_CLK 6 +#define HISTB_I2C1_CLK 7 +#define HISTB_I2C2_CLK 8 +#define HISTB_I2C3_CLK 9 +#define HISTB_I2C4_CLK 10 +#define HISTB_I2C5_CLK 11 +#define HISTB_SPI0_CLK 12 +#define HISTB_SPI1_CLK 13 +#define HISTB_SPI2_CLK 14 #define HISTB_SCI_CLK 15 #define HISTB_FMC_CLK 16 #define HISTB_MMC_BIU_CLK 17 @@ -43,7 +43,7 @@ #define HISTB_SDIO0_BIU_CLK 21 #define HISTB_SDIO0_CIU_CLK 22 #define HISTB_SDIO0_DRV_CLK 23 -#define HISTB_SDIO0_SAMPLE_CLK 24 +#define HISTB_SDIO0_SAMPLE_CLK 24 #define HISTB_PCIE_AUX_CLK 25 #define HISTB_PCIE_PIPE_CLK 26 #define HISTB_PCIE_SYS_CLK 27 @@ -53,14 +53,30 @@ #define HISTB_ETH1_MAC_CLK 31 #define HISTB_ETH1_MACIF_CLK 32 #define HISTB_COMBPHY1_CLK 33 - +#define HISTB_USB2_BUS_CLK 34 +#define HISTB_USB2_PHY_CLK 35 +#define HISTB_USB2_UTMI_CLK 36 +#define HISTB_USB2_12M_CLK 37 +#define HISTB_USB2_48M_CLK 38 +#define HISTB_USB2_OTG_UTMI_CLK 39 +#define HISTB_USB2_PHY1_REF_CLK 40 +#define HISTB_USB2_PHY2_REF_CLK 41 +#define HISTB_COMBPHY0_CLK 42 +#define HISTB_USB3_BUS_CLK 43 +#define HISTB_USB3_UTMI_CLK 44 +#define HISTB_USB3_PIPE_CLK 45 +#define HISTB_USB3_SUSPEND_CLK 46 +#define HISTB_USB3_BUS_CLK1 47 +#define HISTB_USB3_UTMI_CLK1 48 +#define HISTB_USB3_PIPE_CLK1 49 +#define HISTB_USB3_SUSPEND_CLK1 50 /* clocks provided by mcu CRG */ -#define HISTB_MCE_CLK 1 -#define HISTB_IR_CLK 2 -#define HISTB_TIMER01_CLK 3 -#define HISTB_LEDC_CLK 4 -#define HISTB_UART0_CLK 5 -#define HISTB_LSADC_CLK 6 +#define HISTB_MCE_CLK 1 +#define HISTB_IR_CLK 2 +#define HISTB_TIMER01_CLK 3 +#define HISTB_LEDC_CLK 4 +#define HISTB_UART0_CLK 5 +#define HISTB_LSADC_CLK 6 #endif /* __DTS_HISTB_CLOCK_H */ diff --git a/include/dt-bindings/pinctrl/hisi.h b/include/dt-bindings/pinctrl/hisi.h new file mode 100644 index 000000000000..0359bfdc9119 --- /dev/null +++ b/include/dt-bindings/pinctrl/hisi.h @@ -0,0 +1,74 @@ +/* + * This header provides constants for hisilicon pinctrl bindings. + * + * Copyright (c) 2015 Hisilicon Limited. + * Copyright (c) 2015 Linaro Limited. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _DT_BINDINGS_PINCTRL_HISI_H +#define _DT_BINDINGS_PINCTRL_HISI_H + +/* iomg bit definition */ +#define MUX_M0 0 +#define MUX_M1 1 +#define MUX_M2 2 +#define MUX_M3 3 +#define MUX_M4 4 +#define MUX_M5 5 +#define MUX_M6 6 +#define MUX_M7 7 + +/* iocg bit definition */ +#define PULL_MASK (3) +#define PULL_DIS (0) +#define PULL_UP (1 << 0) +#define PULL_DOWN (1 << 1) + +/* drive strength definition */ +#define DRIVE_MASK (7 << 4) +#define DRIVE1_02MA (0 << 4) +#define DRIVE1_04MA (1 << 4) +#define DRIVE1_08MA (2 << 4) +#define DRIVE1_10MA (3 << 4) +#define DRIVE2_02MA (0 << 4) +#define DRIVE2_04MA (1 << 4) +#define DRIVE2_08MA (2 << 4) +#define DRIVE2_10MA (3 << 4) +#define DRIVE3_04MA (0 << 4) +#define DRIVE3_08MA (1 << 4) +#define DRIVE3_12MA (2 << 4) +#define DRIVE3_16MA (3 << 4) +#define DRIVE3_20MA (4 << 4) +#define DRIVE3_24MA (5 << 4) +#define DRIVE3_32MA (6 << 4) +#define DRIVE3_40MA (7 << 4) +#define DRIVE4_02MA (0 << 4) +#define DRIVE4_04MA (2 << 4) +#define DRIVE4_08MA (4 << 4) +#define DRIVE4_10MA (6 << 4) + +/* drive strength definition for hi3660 */ +#define DRIVE6_MASK (15 << 4) +#define DRIVE6_04MA (0 << 4) +#define DRIVE6_12MA (4 << 4) +#define DRIVE6_19MA (8 << 4) +#define DRIVE6_27MA (10 << 4) +#define DRIVE6_32MA (15 << 4) +#define DRIVE7_02MA (0 << 4) +#define DRIVE7_04MA (1 << 4) +#define DRIVE7_06MA (2 << 4) +#define DRIVE7_08MA (3 << 4) +#define DRIVE7_10MA (4 << 4) +#define DRIVE7_12MA (5 << 4) +#define DRIVE7_14MA (6 << 4) +#define DRIVE7_16MA (7 << 4) +#endif -- 2.18.0