[U-Boot] [PATCH 1/3] sunxi: Sync Bananapi M2+ device tree from Linux v5.0-rc1

[Chen-Yu Tsai <wens@csie.org>]

As of commit aa8fee415f46 ("ARM: dts: sun8i: h3: Split out
non-SoC-specific parts of Bananapi M2 Plus") in the Linux kernel, the
device tree for the Bananapi M2+ has been split into a common dtsi file,
and an SoC-specific board device tree file that includes both the shared
dtsi file and the soc dtsi file. This was done to support both the H3
and H5 variants of the same board. This is similar to what was doen for
the Libre Computer ALL-H3-CC in U-boot commit d7b17f1c24af ("sunxi: Split
out common board design for ALL-H3-CC device tree").

The newly split files are directly synced from Linux tag v5.0-rc1.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---

 arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts    | 190 +-----------------
 ...2-plus.dts => sunxi-bananapi-m2-plus.dtsi} |  23 ++-
 2 files changed, 18 insertions(+), 195 deletions(-)
 copy arch/arm/dts/{sun8i-h3-bananapi-m2-plus.dts => sunxi-bananapi-m2-plus.dtsi} (92%)

diff --git a/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts
index 30540dc8e0c5..195a75da13f1 100644
--- a/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -42,195 +42,9 @@
 
 /dts-v1/;
 #include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "sunxi-bananapi-m2-plus.dtsi"
 
 / {
-	model = "Banana Pi BPI-M2-Plus";
+	model = "Banana Pi BPI-M2-Plus H3";
 	compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
-
-	aliases {
-		ethernet0 = &emac;
-		serial0 = &uart0;
-		serial1 = &uart1;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con_in: endpoint {
-				remote-endpoint = <&hdmi_out_con>;
-			};
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-
-		pwr_led {
-			label = "bananapi-m2-plus:red:pwr";
-			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
-			default-state = "on";
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-
-		sw4 {
-			label = "power";
-			linux,code = <BTN_0>;
-			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	reg_gmac_3v3: gmac-3v3 {
-		      compatible = "regulator-fixed";
-		      regulator-name = "gmac-3v3";
-		      regulator-min-microvolt = <3300000>;
-		      regulator-max-microvolt = <3300000>;
-		      startup-delay-us = <100000>;
-		      enable-active-high;
-		      gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
-	};
-
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-	};
-};
-
-&de {
-	status = "okay";
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&ehci2 {
-	status = "okay";
-};
-
-&emac {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emac_rgmii_pins>;
-	phy-supply = <&reg_gmac_3v3>;
-	phy-handle = <&ext_rgmii_phy>;
-	phy-mode = "rgmii";
-
-	status = "okay";
-};
-
-&external_mdio {
-	ext_rgmii_phy: ethernet-phy at 1 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
-	};
-};
-
-&hdmi {
-	status = "okay";
-};
-
-&hdmi_out {
-	hdmi_out_con: endpoint {
-		remote-endpoint = <&hdmi_con_in>;
-	};
-};
-
-&ir {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
-	status = "okay";
-};
-
-&mmc0 {
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
-	status = "okay";
-};
-
-&mmc1 {
-	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	bus-width = <4>;
-	non-removable;
-	status = "okay";
-
-	brcmf: wifi at 1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-		interrupt-parent = <&pio>;
-		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
-		interrupt-names = "host-wake";
-	};
-};
-
-&mmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_8bit_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
-	bus-width = <8>;
-	non-removable;
-	status = "okay";
-};
-
-&ohci0 {
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&ohci2 {
-	status = "okay";
-};
-
-&reg_usb0_vbus {
-	gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
-	status = "okay";
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
-	status = "okay";
-};
-
-&usb_otg {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&usbphy {
-	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
-	usb0_vbus-supply = <&reg_usb0_vbus>;
-	/* USB host VBUS is on as long as VCC-IO is on */
-	status = "okay";
 };
diff --git a/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
similarity index 92%
copy from arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts
copy to arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
index 30540dc8e0c5..3bed375b9c03 100644
--- a/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
@@ -40,17 +40,12 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-/dts-v1/;
-#include "sun8i-h3.dtsi"
 #include "sunxi-common-regulators.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 
 / {
-	model = "Banana Pi BPI-M2-Plus";
-	compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
-
 	aliases {
 		ethernet0 = &emac;
 		serial0 = &uart0;
@@ -108,6 +103,8 @@
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
 	};
 };
 
@@ -140,7 +137,7 @@
 &external_mdio {
 	ext_rgmii_phy: ethernet-phy at 1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
+		reg = <1>;
 	};
 };
 
@@ -220,7 +217,19 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
-	status = "okay";
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	};
 };
 
 &usb_otg {
-- 
2.20.1