All of lore.kernel.org
 help / color / mirror / Atom feed
From: rosysong at rosinson.com <rosysong@rosinson.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] Kernel hang when replace older uboot with uboot master
Date: Tue, 19 Feb 2019 16:56:04 +0800	[thread overview]
Message-ID: <2019021916560430669312@rosinson.com> (raw)

Hi all, 
    This log show the bootlog that when I replace older uboot with uboot master  on my machine. Any hints will be appreciated!!!

## Current stack ends at 0x87f5db80
*  kernel: cmdline image address = 0x9f060000
## Booting kernel from Legacy Image at 9f060000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.101
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1615030 Bytes = 1.5 MiB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   kernel data at 0x9f060040, len = 0x0018a4b6 (1615030)
## No init Ramdisk
   ramdisk start = 0x00000000, ramdisk end = 0x00000000
## No Flattened Device Tree
Continuing to boot without FDT
Initial value for argc=3
Final value for argc=3
   Uncompressing Kernel Image ... LZMA: Image address............... 0x9f060040
LZMA: Properties address.......... 0x9f060040
LZMA: Uncompressed size address... 0x9f060045
LZMA: Compressed data address..... 0x9f06004d
LZMA: Destination address......... 0x80060000
LZMA: Uncompresed size............ 0x4e4f49
LZMA: Compresed size.............. 0x18a4b1
LZMA: Uncompressed ............... 0x4e4f49
OK
   kernel loaded at 0x80060000, end = 0x80544f49
## initrd_high = 0x88000000, copy_to_ram = 1
   ramdisk load start = 0x00000000, ramdisk load end = 0x00000000
Initial value for argc=3
Final value for argc=3
Initial value for argc=3
Final value for argc=3
## initrd_high = 0x88000000, copy_to_ram = 1
   ramdisk load start = 0x00000000, ramdisk load end = 0x00000000
## cmdline argv at 0xa7f70e40, argp at 0xa7f7127d
   arg 001: console=ttyS0,115200
   arg 002: root=/dev/mtdblock5
   arg 003: rootfstype=squashfs
## Giving linux memsize in MB, 128
## Transferring control to Linux (at address 80060000) ...
[    0.000000] Linux version 4.14.101 (xxx at xxx-PC) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r8997-488af51f81)) #0 Mon Feb 18 15:11:32 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is ROSINSON WR818
[    0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 123184K/131072K available (3777K kernel code, 150K rwdata, 912K rodata, 1232K init, 204K bss, 7888K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 775.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[    0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[    0.008841] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.075897] pid_max: default: 32768 minimum: 301
[    0.081291] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.088805] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100199] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.111385] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.118371] pinctrl core: initialized pinctrl subsystem
[    0.125118] NET: Registered protocol family 16
[    0.152756] clocksource: Switched to clocksource MIPS
[    0.159367] NET: Registered protocol family 2
[    0.164968] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.172929] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.180151] TCP: Hash tables configured (established 1024 bind 1024)
[    0.187497] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.194172] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.201498] NET: Registered protocol family 1
[    0.209200] Crashlog allocated RAM at address 0x3f00000
[    0.216285] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.227594] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.234248] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.253131] io scheduler noop registered
[    0.257584] io scheduler deadline registered (default)
[    0.263708] ar7200-usb-phy usb-phy: phy reset is missing
[    0.271233] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
[    0.280104] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.287943] console [ttyS0] disabled
[    0.292032] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 8, base_baud = 1562500) is a 16550A
[    0.301853] console [ttyS0] enabled
[    0.301853] console [ttyS0] enabled
[    0.309411] bootconsole [early0] disabled
[    0.309411] bootconsole [early0] disabled
[    0.332426] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.337373] 5 fixed-partitions partitions found on MTD device spi0.0
[    0.343943] Creating 5 MTD partitions on "spi0.0":
[    0.348898] 0x000000000000-0x000000040000 : "u-boot"
[    0.354737] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.360856] 0x000000050000-0x000000060000 : "factory"
[    0.366741] 0x000000060000-0x000000fe0000 : "firmware"
[    0.374897] 2 uimage-fw partitions found on MTD device firmware
[    0.381019] Creating 2 MTD partitions on "firmware":
[    0.386186] 0x000000000000-0x000000190000 : "kernel"
[    0.391956] 0x000000190000-0x000000f80000 : "rootfs"
[    0.397706] mtd: device 5 (rootfs) set to be root filesystem
[    0.403623] 1 squashfs-split partitions found on MTD device rootfs
[    0.410014] 0x000000440000-0x000000f80000 : "rootfs_data"
[    0.416213] 0x000000ff0000-0x000001000000 : "art"
[    0.422610] libphy: Fixed MDIO Bus: probed
[    0.763118] libphy: ag71xx_mdio: probed
[    0.770064] switch0: Atheros AR8337 rev. 2 switch registered on mdio-bus.0
[    1.424562] ag71xx 19000000.eth: invalid MAC address, using random address
[    1.763918] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    1.775514] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:SGMII
[    1.783553] NET: Registered protocol family 10
[    1.791482] Segment Routing with IPv6
[    1.795402] NET: Registered protocol family 17
[    1.800029] 8021q: 802.1Q VLAN Support v1.8
[    1.809949] SQUASHFS error: xz decompression failed, data probably corrupt
[    1.817103] SQUASHFS error: squashfs_read_data failed to read block 0x29f61c
[    1.824387] SQUASHFS error: Unable to read metadata cache entry [29f61c]
[    1.831302] SQUASHFS error: Unable to read inode 0x2146084e
[    1.837412] VFS: Cannot open root device "(null)" or unknown-block(31,5): error -5
[    1.845254] Please append a correct "root=" boot option; here are the available partitions:
[    1.853888] 1f00             256 mtdblock0 
[    1.853892]  (driver?)
[    1.860640] 1f01              64 mtdblock1 
[    1.860643]  (driver?)
[    1.867396] 1f02              64 mtdblock2 
[    1.867399]  (driver?)
[    1.874149] 1f03           15872 mtdblock3 
[    1.874153]  (driver?)
[    1.880897] 1f04            1600 mtdblock4 
[    1.880900]  (driver?)
[    1.887654] 1f05           14272 mtdblock5 
[    1.887657]  (driver?)
[    1.894407] 1f06           11520 mtdblock6 
[    1.894410]  (driver?)
[    1.901156] 1f07              64 mtdblock7 
[    1.901159]  (driver?)
[    1.907912] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)
[    1.917125] Rebooting in 1 seconds..

                 reply	other threads:[~2019-02-19  8:56 UTC|newest]

Thread overview: [no followups] expand[flat|nested]  mbox.gz  Atom feed

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=2019021916560430669312@rosinson.com \
    --to=rosysong@rosinson.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.