* [PATCH 0/2] Patches for i2c-stm32 device tree bindings @ 2019-03-06 15:11 ` Bich HEMON 0 siblings, 0 replies; 21+ messages in thread From: Bich HEMON @ 2019-03-06 15:11 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Cc: Bich HEMON This patchset provides dt-bindings updates for I2C. Bich Hemon (2): dt-bindings: i2c-stm32: remove extra spaces dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 .../devicetree/bindings/i2c/i2c-stm32.txt | 37 +++++++++++----------- 1 file changed, 19 insertions(+), 18 deletions(-) -- 1.9.1 ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 0/2] Patches for i2c-stm32 device tree bindings @ 2019-03-06 15:11 ` Bich HEMON 0 siblings, 0 replies; 21+ messages in thread From: Bich HEMON @ 2019-03-06 15:11 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Cc: Bich HEMON This patchset provides dt-bindings updates for I2C. Bich Hemon (2): dt-bindings: i2c-stm32: remove extra spaces dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 .../devicetree/bindings/i2c/i2c-stm32.txt | 37 +++++++++++----------- 1 file changed, 19 insertions(+), 18 deletions(-) -- 1.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 0/2] Patches for i2c-stm32 device tree bindings @ 2019-03-06 15:11 ` Bich HEMON 0 siblings, 0 replies; 21+ messages in thread From: Bich HEMON @ 2019-03-06 15:11 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Cc: Bich HEMON This patchset provides dt-bindings updates for I2C. Bich Hemon (2): dt-bindings: i2c-stm32: remove extra spaces dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 .../devicetree/bindings/i2c/i2c-stm32.txt | 37 +++++++++++----------- 1 file changed, 19 insertions(+), 18 deletions(-) -- 1.9.1 ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 2019-03-06 15:11 ` Bich HEMON (?) @ 2019-03-06 15:11 ` Bich HEMON -1 siblings, 0 replies; 21+ messages in thread From: Bich HEMON @ 2019-03-06 15:11 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Cc: Bich HEMON Add STM32H7 and STM32MP1 in the list of compatible socs for each optional property. Signed-off-by: Bich Hemon <bich.hemon@st.com> --- Documentation/devicetree/bindings/i2c/i2c-stm32.txt | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-) diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index 7d054f1..f334738 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -19,18 +19,19 @@ Optional properties: the default 100 kHz frequency will be used. For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are 100000 and 400000. - For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, - possible values are 100000, 400000 and 1000000. -- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board - (default: 25) -- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board - (default: 10) + For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode, Fast-mode and Fast-mode + Plus are supported, possible values are 100000, 400000 and 1000000. +- i2c-scl-rising-time-ns: I2C SCL Rising time for the board (default: 25) + For STM32F7, STM32H7 and STM32MP1 only. +- i2c-scl-falling-time-ns: I2C SCL Falling time for the board (default: 10) + For STM32F7, STM32H7 and STM32MP1 only. I2C Timings are derived from these 2 values -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG - whether Fast Mode Plus speed is selected by slave. +- st,syscfg-fmp: Use to set Fast Mode Plus bit within SYSCFG when Fast Mode + Plus speed is selected by slave. 1st cell: phandle to syscfg 2nd cell: register offset within SYSCFG 3rd cell: register bitmask for FMP bit + For STM32F7, STM32H7 and STM32MP1 only. Example: -- 1.9.1 ^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 @ 2019-03-06 15:11 ` Bich HEMON 0 siblings, 0 replies; 21+ messages in thread From: Bich HEMON @ 2019-03-06 15:11 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Cc: Bich HEMON Add STM32H7 and STM32MP1 in the list of compatible socs for each optional property. Signed-off-by: Bich Hemon <bich.hemon@st.com> --- Documentation/devicetree/bindings/i2c/i2c-stm32.txt | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-) diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index 7d054f1..f334738 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -19,18 +19,19 @@ Optional properties: the default 100 kHz frequency will be used. For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are 100000 and 400000. - For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, - possible values are 100000, 400000 and 1000000. -- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board - (default: 25) -- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board - (default: 10) + For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode, Fast-mode and Fast-mode + Plus are supported, possible values are 100000, 400000 and 1000000. +- i2c-scl-rising-time-ns: I2C SCL Rising time for the board (default: 25) + For STM32F7, STM32H7 and STM32MP1 only. +- i2c-scl-falling-time-ns: I2C SCL Falling time for the board (default: 10) + For STM32F7, STM32H7 and STM32MP1 only. I2C Timings are derived from these 2 values -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG - whether Fast Mode Plus speed is selected by slave. +- st,syscfg-fmp: Use to set Fast Mode Plus bit within SYSCFG when Fast Mode + Plus speed is selected by slave. 1st cell: phandle to syscfg 2nd cell: register offset within SYSCFG 3rd cell: register bitmask for FMP bit + For STM32F7, STM32H7 and STM32MP1 only. Example: -- 1.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 @ 2019-03-06 15:11 ` Bich HEMON 0 siblings, 0 replies; 21+ messages in thread From: Bich HEMON @ 2019-03-06 15:11 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Cc: Bich HEMON Add STM32H7 and STM32MP1 in the list of compatible socs for each optional property. Signed-off-by: Bich Hemon <bich.hemon@st.com> --- Documentation/devicetree/bindings/i2c/i2c-stm32.txt | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-) diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index 7d054f1..f334738 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -19,18 +19,19 @@ Optional properties: the default 100 kHz frequency will be used. For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are 100000 and 400000. - For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, - possible values are 100000, 400000 and 1000000. -- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board - (default: 25) -- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board - (default: 10) + For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode, Fast-mode and Fast-mode + Plus are supported, possible values are 100000, 400000 and 1000000. +- i2c-scl-rising-time-ns: I2C SCL Rising time for the board (default: 25) + For STM32F7, STM32H7 and STM32MP1 only. +- i2c-scl-falling-time-ns: I2C SCL Falling time for the board (default: 10) + For STM32F7, STM32H7 and STM32MP1 only. I2C Timings are derived from these 2 values -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG - whether Fast Mode Plus speed is selected by slave. +- st,syscfg-fmp: Use to set Fast Mode Plus bit within SYSCFG when Fast Mode + Plus speed is selected by slave. 1st cell: phandle to syscfg 2nd cell: register offset within SYSCFG 3rd cell: register bitmask for FMP bit + For STM32F7, STM32H7 and STM32MP1 only. Example: -- 1.9.1 ^ permalink raw reply related [flat|nested] 21+ messages in thread
* Re: [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 2019-03-06 15:11 ` Bich HEMON (?) @ 2019-03-21 8:28 ` Pierre Yves MORDRET -1 siblings, 0 replies; 21+ messages in thread From: Pierre Yves MORDRET @ 2019-03-21 8:28 UTC (permalink / raw) To: Bich HEMON, Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> On 3/6/19 4:11 PM, Bich HEMON wrote: > Add STM32H7 and STM32MP1 in the list of compatible socs for each > optional property. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> > --- > Documentation/devicetree/bindings/i2c/i2c-stm32.txt | 17 +++++++++-------- > 1 file changed, 9 insertions(+), 8 deletions(-) > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > index 7d054f1..f334738 100644 > --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > @@ -19,18 +19,19 @@ Optional properties: > the default 100 kHz frequency will be used. > For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are > 100000 and 400000. > - For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, > - possible values are 100000, 400000 and 1000000. > -- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board > - (default: 25) > -- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board > - (default: 10) > + For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode, Fast-mode and Fast-mode > + Plus are supported, possible values are 100000, 400000 and 1000000. > +- i2c-scl-rising-time-ns: I2C SCL Rising time for the board (default: 25) > + For STM32F7, STM32H7 and STM32MP1 only. > +- i2c-scl-falling-time-ns: I2C SCL Falling time for the board (default: 10) > + For STM32F7, STM32H7 and STM32MP1 only. > I2C Timings are derived from these 2 values > -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG > - whether Fast Mode Plus speed is selected by slave. > +- st,syscfg-fmp: Use to set Fast Mode Plus bit within SYSCFG when Fast Mode > + Plus speed is selected by slave. > 1st cell: phandle to syscfg > 2nd cell: register offset within SYSCFG > 3rd cell: register bitmask for FMP bit > + For STM32F7, STM32H7 and STM32MP1 only. > > Example: > > ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 @ 2019-03-21 8:28 ` Pierre Yves MORDRET 0 siblings, 0 replies; 21+ messages in thread From: Pierre Yves MORDRET @ 2019-03-21 8:28 UTC (permalink / raw) To: Bich HEMON, Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> On 3/6/19 4:11 PM, Bich HEMON wrote: > Add STM32H7 and STM32MP1 in the list of compatible socs for each > optional property. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> > --- > Documentation/devicetree/bindings/i2c/i2c-stm32.txt | 17 +++++++++-------- > 1 file changed, 9 insertions(+), 8 deletions(-) > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > index 7d054f1..f334738 100644 > --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > @@ -19,18 +19,19 @@ Optional properties: > the default 100 kHz frequency will be used. > For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are > 100000 and 400000. > - For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, > - possible values are 100000, 400000 and 1000000. > -- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board > - (default: 25) > -- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board > - (default: 10) > + For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode, Fast-mode and Fast-mode > + Plus are supported, possible values are 100000, 400000 and 1000000. > +- i2c-scl-rising-time-ns: I2C SCL Rising time for the board (default: 25) > + For STM32F7, STM32H7 and STM32MP1 only. > +- i2c-scl-falling-time-ns: I2C SCL Falling time for the board (default: 10) > + For STM32F7, STM32H7 and STM32MP1 only. > I2C Timings are derived from these 2 values > -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG > - whether Fast Mode Plus speed is selected by slave. > +- st,syscfg-fmp: Use to set Fast Mode Plus bit within SYSCFG when Fast Mode > + Plus speed is selected by slave. > 1st cell: phandle to syscfg > 2nd cell: register offset within SYSCFG > 3rd cell: register bitmask for FMP bit > + For STM32F7, STM32H7 and STM32MP1 only. > > Example: > > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 @ 2019-03-21 8:28 ` Pierre Yves MORDRET 0 siblings, 0 replies; 21+ messages in thread From: Pierre Yves MORDRET @ 2019-03-21 8:28 UTC (permalink / raw) To: Bich HEMON, Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> On 3/6/19 4:11 PM, Bich HEMON wrote: > Add STM32H7 and STM32MP1 in the list of compatible socs for each > optional property. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> > --- > Documentation/devicetree/bindings/i2c/i2c-stm32.txt | 17 +++++++++-------- > 1 file changed, 9 insertions(+), 8 deletions(-) > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > index 7d054f1..f334738 100644 > --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > @@ -19,18 +19,19 @@ Optional properties: > the default 100 kHz frequency will be used. > For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are > 100000 and 400000. > - For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, > - possible values are 100000, 400000 and 1000000. > -- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board > - (default: 25) > -- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board > - (default: 10) > + For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode, Fast-mode and Fast-mode > + Plus are supported, possible values are 100000, 400000 and 1000000. > +- i2c-scl-rising-time-ns: I2C SCL Rising time for the board (default: 25) > + For STM32F7, STM32H7 and STM32MP1 only. > +- i2c-scl-falling-time-ns: I2C SCL Falling time for the board (default: 10) > + For STM32F7, STM32H7 and STM32MP1 only. > I2C Timings are derived from these 2 values > -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG > - whether Fast Mode Plus speed is selected by slave. > +- st,syscfg-fmp: Use to set Fast Mode Plus bit within SYSCFG when Fast Mode > + Plus speed is selected by slave. > 1st cell: phandle to syscfg > 2nd cell: register offset within SYSCFG > 3rd cell: register bitmask for FMP bit > + For STM32F7, STM32H7 and STM32MP1 only. > > Example: > > ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 2019-03-06 15:11 ` Bich HEMON (?) @ 2019-03-24 22:15 ` Wolfram Sang -1 siblings, 0 replies; 21+ messages in thread From: Wolfram Sang @ 2019-03-24 22:15 UTC (permalink / raw) To: Bich HEMON Cc: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel [-- Attachment #1: Type: text/plain, Size: 238 bytes --] On Wed, Mar 06, 2019 at 03:11:51PM +0000, Bich HEMON wrote: > Add STM32H7 and STM32MP1 in the list of compatible socs for each > optional property. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> Applied to for-next, thanks! [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 @ 2019-03-24 22:15 ` Wolfram Sang 0 siblings, 0 replies; 21+ messages in thread From: Wolfram Sang @ 2019-03-24 22:15 UTC (permalink / raw) To: Bich HEMON Cc: Mark Rutland, devicetree, Alexandre TORGUE, linux-kernel, Pierre Yves MORDRET, Rob Herring, linux-i2c, Maxime Coquelin, linux-stm32, linux-arm-kernel [-- Attachment #1.1: Type: text/plain, Size: 238 bytes --] On Wed, Mar 06, 2019 at 03:11:51PM +0000, Bich HEMON wrote: > Add STM32H7 and STM32MP1 in the list of compatible socs for each > optional property. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> Applied to for-next, thanks! [-- Attachment #1.2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] [-- Attachment #2: Type: text/plain, Size: 176 bytes --] _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 @ 2019-03-24 22:15 ` Wolfram Sang 0 siblings, 0 replies; 21+ messages in thread From: Wolfram Sang @ 2019-03-24 22:15 UTC (permalink / raw) To: Bich HEMON Cc: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel [-- Attachment #1: Type: text/plain, Size: 238 bytes --] On Wed, Mar 06, 2019 at 03:11:51PM +0000, Bich HEMON wrote: > Add STM32H7 and STM32MP1 in the list of compatible socs for each > optional property. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> Applied to for-next, thanks! [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces 2019-03-06 15:11 ` Bich HEMON (?) @ 2019-03-06 15:11 ` Bich HEMON -1 siblings, 0 replies; 21+ messages in thread From: Bich HEMON @ 2019-03-06 15:11 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Cc: Bich HEMON Remove extra spaces before colons. Signed-off-by: Bich Hemon <bich.hemon@st.com> --- .../devicetree/bindings/i2c/i2c-stm32.txt | 26 +++++++++++----------- 1 file changed, 13 insertions(+), 13 deletions(-) diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index 69240e1..7d054f1 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -1,11 +1,11 @@ * I2C controller embedded in STMicroelectronics STM32 I2C platform -Required properties : -- compatible : Must be one of the following +Required properties: +- compatible: Must be one of the following - "st,stm32f4-i2c" - "st,stm32f7-i2c" -- reg : Offset and length of the register set for the device -- interrupts : Must contain the interrupt id for I2C event and then the +- reg: Offset and length of the register set for the device +- interrupts: Must contain the interrupt id for I2C event and then the interrupt id for I2C error. - resets: Must contain the phandle to the reset controller. - clocks: Must contain the input clock of the I2C instance. @@ -14,25 +14,25 @@ Required properties : - #address-cells = <1>; - #size-cells = <0>; -Optional properties : -- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, +Optional properties: +- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified, the default 100 kHz frequency will be used. For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are 100000 and 400000. For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, possible values are 100000, 400000 and 1000000. -- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board +- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board (default: 25) -- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board +- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board (default: 10) I2C Timings are derived from these 2 values -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG +- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG whether Fast Mode Plus speed is selected by slave. - 1st cell : phandle to syscfg - 2nd cell : register offset within SYSCFG - 3rd cell : register bitmask for FMP bit + 1st cell: phandle to syscfg + 2nd cell: register offset within SYSCFG + 3rd cell: register bitmask for FMP bit -Example : +Example: i2c@40005400 { compatible = "st,stm32f4-i2c"; -- 1.9.1 ^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces @ 2019-03-06 15:11 ` Bich HEMON 0 siblings, 0 replies; 21+ messages in thread From: Bich HEMON @ 2019-03-06 15:11 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Cc: Bich HEMON Remove extra spaces before colons. Signed-off-by: Bich Hemon <bich.hemon@st.com> --- .../devicetree/bindings/i2c/i2c-stm32.txt | 26 +++++++++++----------- 1 file changed, 13 insertions(+), 13 deletions(-) diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index 69240e1..7d054f1 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -1,11 +1,11 @@ * I2C controller embedded in STMicroelectronics STM32 I2C platform -Required properties : -- compatible : Must be one of the following +Required properties: +- compatible: Must be one of the following - "st,stm32f4-i2c" - "st,stm32f7-i2c" -- reg : Offset and length of the register set for the device -- interrupts : Must contain the interrupt id for I2C event and then the +- reg: Offset and length of the register set for the device +- interrupts: Must contain the interrupt id for I2C event and then the interrupt id for I2C error. - resets: Must contain the phandle to the reset controller. - clocks: Must contain the input clock of the I2C instance. @@ -14,25 +14,25 @@ Required properties : - #address-cells = <1>; - #size-cells = <0>; -Optional properties : -- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, +Optional properties: +- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified, the default 100 kHz frequency will be used. For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are 100000 and 400000. For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, possible values are 100000, 400000 and 1000000. -- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board +- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board (default: 25) -- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board +- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board (default: 10) I2C Timings are derived from these 2 values -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG +- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG whether Fast Mode Plus speed is selected by slave. - 1st cell : phandle to syscfg - 2nd cell : register offset within SYSCFG - 3rd cell : register bitmask for FMP bit + 1st cell: phandle to syscfg + 2nd cell: register offset within SYSCFG + 3rd cell: register bitmask for FMP bit -Example : +Example: i2c@40005400 { compatible = "st,stm32f4-i2c"; -- 1.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces @ 2019-03-06 15:11 ` Bich HEMON 0 siblings, 0 replies; 21+ messages in thread From: Bich HEMON @ 2019-03-06 15:11 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Cc: Bich HEMON Remove extra spaces before colons. Signed-off-by: Bich Hemon <bich.hemon@st.com> --- .../devicetree/bindings/i2c/i2c-stm32.txt | 26 +++++++++++----------- 1 file changed, 13 insertions(+), 13 deletions(-) diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index 69240e1..7d054f1 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -1,11 +1,11 @@ * I2C controller embedded in STMicroelectronics STM32 I2C platform -Required properties : -- compatible : Must be one of the following +Required properties: +- compatible: Must be one of the following - "st,stm32f4-i2c" - "st,stm32f7-i2c" -- reg : Offset and length of the register set for the device -- interrupts : Must contain the interrupt id for I2C event and then the +- reg: Offset and length of the register set for the device +- interrupts: Must contain the interrupt id for I2C event and then the interrupt id for I2C error. - resets: Must contain the phandle to the reset controller. - clocks: Must contain the input clock of the I2C instance. @@ -14,25 +14,25 @@ Required properties : - #address-cells = <1>; - #size-cells = <0>; -Optional properties : -- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, +Optional properties: +- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified, the default 100 kHz frequency will be used. For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are 100000 and 400000. For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, possible values are 100000, 400000 and 1000000. -- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board +- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board (default: 25) -- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board +- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board (default: 10) I2C Timings are derived from these 2 values -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG +- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG whether Fast Mode Plus speed is selected by slave. - 1st cell : phandle to syscfg - 2nd cell : register offset within SYSCFG - 3rd cell : register bitmask for FMP bit + 1st cell: phandle to syscfg + 2nd cell: register offset within SYSCFG + 3rd cell: register bitmask for FMP bit -Example : +Example: i2c@40005400 { compatible = "st,stm32f4-i2c"; -- 1.9.1 ^ permalink raw reply related [flat|nested] 21+ messages in thread
* Re: [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces 2019-03-06 15:11 ` Bich HEMON (?) @ 2019-03-21 8:28 ` Pierre Yves MORDRET -1 siblings, 0 replies; 21+ messages in thread From: Pierre Yves MORDRET @ 2019-03-21 8:28 UTC (permalink / raw) To: Bich HEMON, Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> On 3/6/19 4:11 PM, Bich HEMON wrote: > Remove extra spaces before colons. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> > --- > .../devicetree/bindings/i2c/i2c-stm32.txt | 26 +++++++++++----------- > 1 file changed, 13 insertions(+), 13 deletions(-) > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > index 69240e1..7d054f1 100644 > --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > @@ -1,11 +1,11 @@ > * I2C controller embedded in STMicroelectronics STM32 I2C platform > > -Required properties : > -- compatible : Must be one of the following > +Required properties: > +- compatible: Must be one of the following > - "st,stm32f4-i2c" > - "st,stm32f7-i2c" > -- reg : Offset and length of the register set for the device > -- interrupts : Must contain the interrupt id for I2C event and then the > +- reg: Offset and length of the register set for the device > +- interrupts: Must contain the interrupt id for I2C event and then the > interrupt id for I2C error. > - resets: Must contain the phandle to the reset controller. > - clocks: Must contain the input clock of the I2C instance. > @@ -14,25 +14,25 @@ Required properties : > - #address-cells = <1>; > - #size-cells = <0>; > > -Optional properties : > -- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, > +Optional properties: > +- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified, > the default 100 kHz frequency will be used. > For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are > 100000 and 400000. > For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, > possible values are 100000, 400000 and 1000000. > -- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board > +- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board > (default: 25) > -- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board > +- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board > (default: 10) > I2C Timings are derived from these 2 values > -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG > +- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG > whether Fast Mode Plus speed is selected by slave. > - 1st cell : phandle to syscfg > - 2nd cell : register offset within SYSCFG > - 3rd cell : register bitmask for FMP bit > + 1st cell: phandle to syscfg > + 2nd cell: register offset within SYSCFG > + 3rd cell: register bitmask for FMP bit > > -Example : > +Example: > > i2c@40005400 { > compatible = "st,stm32f4-i2c"; > ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces @ 2019-03-21 8:28 ` Pierre Yves MORDRET 0 siblings, 0 replies; 21+ messages in thread From: Pierre Yves MORDRET @ 2019-03-21 8:28 UTC (permalink / raw) To: Bich HEMON, Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> On 3/6/19 4:11 PM, Bich HEMON wrote: > Remove extra spaces before colons. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> > --- > .../devicetree/bindings/i2c/i2c-stm32.txt | 26 +++++++++++----------- > 1 file changed, 13 insertions(+), 13 deletions(-) > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > index 69240e1..7d054f1 100644 > --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > @@ -1,11 +1,11 @@ > * I2C controller embedded in STMicroelectronics STM32 I2C platform > > -Required properties : > -- compatible : Must be one of the following > +Required properties: > +- compatible: Must be one of the following > - "st,stm32f4-i2c" > - "st,stm32f7-i2c" > -- reg : Offset and length of the register set for the device > -- interrupts : Must contain the interrupt id for I2C event and then the > +- reg: Offset and length of the register set for the device > +- interrupts: Must contain the interrupt id for I2C event and then the > interrupt id for I2C error. > - resets: Must contain the phandle to the reset controller. > - clocks: Must contain the input clock of the I2C instance. > @@ -14,25 +14,25 @@ Required properties : > - #address-cells = <1>; > - #size-cells = <0>; > > -Optional properties : > -- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, > +Optional properties: > +- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified, > the default 100 kHz frequency will be used. > For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are > 100000 and 400000. > For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, > possible values are 100000, 400000 and 1000000. > -- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board > +- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board > (default: 25) > -- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board > +- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board > (default: 10) > I2C Timings are derived from these 2 values > -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG > +- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG > whether Fast Mode Plus speed is selected by slave. > - 1st cell : phandle to syscfg > - 2nd cell : register offset within SYSCFG > - 3rd cell : register bitmask for FMP bit > + 1st cell: phandle to syscfg > + 2nd cell: register offset within SYSCFG > + 3rd cell: register bitmask for FMP bit > > -Example : > +Example: > > i2c@40005400 { > compatible = "st,stm32f4-i2c"; > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces @ 2019-03-21 8:28 ` Pierre Yves MORDRET 0 siblings, 0 replies; 21+ messages in thread From: Pierre Yves MORDRET @ 2019-03-21 8:28 UTC (permalink / raw) To: Bich HEMON, Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Wolfram Sang, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> On 3/6/19 4:11 PM, Bich HEMON wrote: > Remove extra spaces before colons. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> > --- > .../devicetree/bindings/i2c/i2c-stm32.txt | 26 +++++++++++----------- > 1 file changed, 13 insertions(+), 13 deletions(-) > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > index 69240e1..7d054f1 100644 > --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt > @@ -1,11 +1,11 @@ > * I2C controller embedded in STMicroelectronics STM32 I2C platform > > -Required properties : > -- compatible : Must be one of the following > +Required properties: > +- compatible: Must be one of the following > - "st,stm32f4-i2c" > - "st,stm32f7-i2c" > -- reg : Offset and length of the register set for the device > -- interrupts : Must contain the interrupt id for I2C event and then the > +- reg: Offset and length of the register set for the device > +- interrupts: Must contain the interrupt id for I2C event and then the > interrupt id for I2C error. > - resets: Must contain the phandle to the reset controller. > - clocks: Must contain the input clock of the I2C instance. > @@ -14,25 +14,25 @@ Required properties : > - #address-cells = <1>; > - #size-cells = <0>; > > -Optional properties : > -- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, > +Optional properties: > +- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified, > the default 100 kHz frequency will be used. > For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are > 100000 and 400000. > For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, > possible values are 100000, 400000 and 1000000. > -- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board > +- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board > (default: 25) > -- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board > +- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board > (default: 10) > I2C Timings are derived from these 2 values > -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG > +- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG > whether Fast Mode Plus speed is selected by slave. > - 1st cell : phandle to syscfg > - 2nd cell : register offset within SYSCFG > - 3rd cell : register bitmask for FMP bit > + 1st cell: phandle to syscfg > + 2nd cell: register offset within SYSCFG > + 3rd cell: register bitmask for FMP bit > > -Example : > +Example: > > i2c@40005400 { > compatible = "st,stm32f4-i2c"; > ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces 2019-03-06 15:11 ` Bich HEMON (?) @ 2019-03-24 22:15 ` Wolfram Sang -1 siblings, 0 replies; 21+ messages in thread From: Wolfram Sang @ 2019-03-24 22:15 UTC (permalink / raw) To: Bich HEMON Cc: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel [-- Attachment #1: Type: text/plain, Size: 186 bytes --] On Wed, Mar 06, 2019 at 03:11:51PM +0000, Bich HEMON wrote: > Remove extra spaces before colons. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> Applied to for-next, thanks! [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces @ 2019-03-24 22:15 ` Wolfram Sang 0 siblings, 0 replies; 21+ messages in thread From: Wolfram Sang @ 2019-03-24 22:15 UTC (permalink / raw) To: Bich HEMON Cc: Mark Rutland, devicetree, Alexandre TORGUE, linux-kernel, Pierre Yves MORDRET, Rob Herring, linux-i2c, Maxime Coquelin, linux-stm32, linux-arm-kernel [-- Attachment #1.1: Type: text/plain, Size: 186 bytes --] On Wed, Mar 06, 2019 at 03:11:51PM +0000, Bich HEMON wrote: > Remove extra spaces before colons. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> Applied to for-next, thanks! [-- Attachment #1.2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] [-- Attachment #2: Type: text/plain, Size: 176 bytes --] _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces @ 2019-03-24 22:15 ` Wolfram Sang 0 siblings, 0 replies; 21+ messages in thread From: Wolfram Sang @ 2019-03-24 22:15 UTC (permalink / raw) To: Bich HEMON Cc: Rob Herring, Mark Rutland, Maxime Coquelin, Alexandre TORGUE, Pierre Yves MORDRET, linux-i2c, devicetree, linux-stm32, linux-arm-kernel, linux-kernel [-- Attachment #1: Type: text/plain, Size: 186 bytes --] On Wed, Mar 06, 2019 at 03:11:51PM +0000, Bich HEMON wrote: > Remove extra spaces before colons. > > Signed-off-by: Bich Hemon <bich.hemon@st.com> Applied to for-next, thanks! [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 21+ messages in thread
end of thread, other threads:[~2019-03-24 22:15 UTC | newest] Thread overview: 21+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-03-06 15:11 [PATCH 0/2] Patches for i2c-stm32 device tree bindings Bich HEMON 2019-03-06 15:11 ` Bich HEMON 2019-03-06 15:11 ` Bich HEMON 2019-03-06 15:11 ` [PATCH 2/2] dt-bindings: i2c-stm32: update optional properties for stm32h7/stm32mp1 Bich HEMON 2019-03-06 15:11 ` Bich HEMON 2019-03-06 15:11 ` Bich HEMON 2019-03-21 8:28 ` Pierre Yves MORDRET 2019-03-21 8:28 ` Pierre Yves MORDRET 2019-03-21 8:28 ` Pierre Yves MORDRET 2019-03-24 22:15 ` Wolfram Sang 2019-03-24 22:15 ` Wolfram Sang 2019-03-24 22:15 ` Wolfram Sang 2019-03-06 15:11 ` [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces Bich HEMON 2019-03-06 15:11 ` Bich HEMON 2019-03-06 15:11 ` Bich HEMON 2019-03-21 8:28 ` Pierre Yves MORDRET 2019-03-21 8:28 ` Pierre Yves MORDRET 2019-03-21 8:28 ` Pierre Yves MORDRET 2019-03-24 22:15 ` Wolfram Sang 2019-03-24 22:15 ` Wolfram Sang 2019-03-24 22:15 ` Wolfram Sang
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.