From mboxrd@z Thu Jan 1 00:00:00 1970 From: Bjorn Andersson Subject: [PATCH v3] arm64: dts: qcom: qcs404: Add PCIe related nodes Date: Wed, 1 May 2019 17:24:08 -0700 Message-ID: <20190502002408.10719-1-bjorn.andersson@linaro.org> Return-path: Sender: linux-kernel-owner@vger.kernel.org To: Andy Gross , David Brown Cc: Rob Herring , Mark Rutland , linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org List-Id: linux-arm-msm@vger.kernel.org The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, add these to the platform dtsi and enable them for the EVB with the perst gpio and analog supplies defined. Reviewed-by: Niklas Cassel Signed-off-by: Bjorn Andersson --- The patch depends on the acceptance of: https://lore.kernel.org/lkml/20190502002138.10646-1-bjorn.andersson@linaro.org/ https://lore.kernel.org/lkml/20190502001406.10431-2-bjorn.andersson@linaro.org/ https://lore.kernel.org/lkml/20190502001955.10575-3-bjorn.andersson@linaro.org/ Changes since v2: - None arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 25 +++++++++ arch/arm64/boot/dts/qcom/qcs404.dtsi | 67 ++++++++++++++++++++++++ 2 files changed, 92 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi index 2c3127167e3c..988d21ca0df1 100644 --- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi +++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi @@ -68,6 +68,22 @@ }; }; +&pcie { + status = "ok"; + + perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&perst_state>; +}; + +&pcie_phy { + status = "ok"; + + vdda-vp-supply = <&vreg_l3_1p05>; + vdda-vph-supply = <&vreg_l5_1p8>; +}; + &remoteproc_adsp { status = "ok"; }; @@ -184,6 +200,15 @@ }; &tlmm { + perst_state: perst { + pins = "gpio43"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + output-low; + }; + sdc1_on: sdc1-on { clk { pins = "sdc1_clk"; diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi index ffedf9640af7..f41feab8996c 100644 --- a/arch/arm64/boot/dts/qcom/qcs404.dtsi +++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi @@ -4,6 +4,7 @@ #include #include #include +#include / { interrupt-parent = <&intc>; @@ -383,6 +384,7 @@ compatible = "qcom,gcc-qcs404"; reg = <0x01800000 0x80000>; #clock-cells = <1>; + #reset-cells = <1>; assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>; assigned-clock-rates = <19200000>; @@ -411,6 +413,21 @@ #interrupt-cells = <4>; }; + pcie_phy: phy@7786000 { + compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy"; + reg = <0x07786000 0xb8>; + + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; + resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>, + <&gcc GCC_PCIE_0_PIPE_ARES>; + reset-names = "phy", "pipe"; + + clock-output-names = "pcie_0_pipe_clk"; + #phy-cells = <0>; + + status = "disabled"; + }; + sdcc1: sdcc@7804000 { compatible = "qcom,sdhci-msm-v5"; reg = <0x07804000 0x1000>, <0x7805000 0x1000>; @@ -796,6 +813,56 @@ status = "disabled"; }; }; + + pcie: pci@10000000 { + compatible = "qcom,pcie-qcs404", "snps,dw-pcie"; + reg = <0x10000000 0xf1d>, + <0x10000f20 0xa8>, + <0x07780000 0x2000>, + <0x10001000 0x2000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0 0x10003000 0 0x00010000>, /* I/O */ + <0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */ + + interrupts = ; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>, + <&gcc GCC_PCIE_0_AUX_CLK>, + <&gcc GCC_PCIE_0_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_0_SLV_AXI_CLK>; + clock-names = "iface", "aux", "master_bus", "slave_bus"; + + resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>, + <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>, + <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>, + <&gcc GCC_PCIE_0_CORE_STICKY_ARES>, + <&gcc GCC_PCIE_0_BCR>, + <&gcc GCC_PCIE_0_AHB_ARES>; + reset-names = "axi_m", + "axi_s", + "axi_m_sticky", + "pipe_sticky", + "pwr", + "ahb"; + + phys = <&pcie_phy>; + phy-names = "pciephy"; + + status = "disabled"; + }; }; timer { -- 2.18.0