From mboxrd@z Thu Jan 1 00:00:00 1970 From: Andreas Dannenberg Date: Tue, 7 May 2019 12:25:33 -0500 Subject: [U-Boot] [PATCH 04/13] arm: K3: Introduce System Firmware loader framework In-Reply-To: <20190507172542.31359-1-dannenberg@ti.com> References: <20190507172542.31359-1-dannenberg@ti.com> Message-ID: <20190507172542.31359-5-dannenberg@ti.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Introduce a framework that allows loading the System Firmware (SYSFW) binary as well as the associated configuration data from an image tree blob named "sysfw.itb" from an FS-based MMC boot media or from an MMC RAW mode partition or sector. To simplify the handling of and loading from the different boot media we tap into the existing U-Boot SPL framework usually used for loading U-Boot by building on an earlier commit that exposes some of that functionality. Note that this initial implementation only supports FS and RAW-based eMMC/SD card boot. Signed-off-by: Andreas Dannenberg Signed-off-by: Lokesh Vutla --- arch/arm/mach-k3/Kconfig | 40 +++ arch/arm/mach-k3/Makefile | 1 + arch/arm/mach-k3/include/mach/sysfw-loader.h | 12 + arch/arm/mach-k3/sysfw-loader.c | 263 +++++++++++++++++++ 4 files changed, 316 insertions(+) create mode 100644 arch/arm/mach-k3/include/mach/sysfw-loader.h create mode 100644 arch/arm/mach-k3/sysfw-loader.c diff --git a/arch/arm/mach-k3/Kconfig b/arch/arm/mach-k3/Kconfig index e677a2e01b..f1731dda58 100644 --- a/arch/arm/mach-k3/Kconfig +++ b/arch/arm/mach-k3/Kconfig @@ -58,6 +58,46 @@ config SYS_K3_BOOT_CORE_ID int default 16 +config K3_LOAD_SYSFW + bool + depends on SPL + default n + +config K3_SYSFW_IMAGE_NAME + string "File name of SYSFW firmware and configuration blob" + depends on K3_LOAD_SYSFW + default "sysfw.itb" + help + Filename of the combined System Firmware and configuration image tree + blob to be loaded when booting from a filesystem. + +config K3_SYSFW_IMAGE_MMCSD_RAW_MODE_SECT + hex "MMC sector to load SYSFW firmware and configuration blob from" + depends on K3_LOAD_SYSFW && SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR + default 0x3600 + help + Address on the MMC to load the combined System Firmware and + configuration image tree blob from, when the MMC is being used + in raw mode. Units: MMC sectors (1 sector = 512 bytes). + +config K3_SYSFW_IMAGE_MMCSD_RAW_MODE_PART + hex "MMC partition to load SYSFW firmware and configuration blob from" + depends on K3_LOAD_SYSFW && SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION + default 2 + help + Partition on the MMC to the combined System Firmware and configuration + image tree blob from, when the MMC is being used in raw mode. + +config K3_SYSFW_IMAGE_SIZE_MAX + int "Amount of memory dynamically allocated for loading SYSFW blob" + depends on K3_LOAD_SYSFW + default 269000 + help + Amount of memory reserved through dynamic allocation at runtime for + loading the combined System Firmware and configuration image tree + blob. Keep it as tight as possible, as this directly affects the + overall SPL memory footprint. + config SYS_K3_SPL_ATF bool "Start Cortex-A from SPL" depends on SPL && CPU_V7R diff --git a/arch/arm/mach-k3/Makefile b/arch/arm/mach-k3/Makefile index 0c3a4f7db1..6c895400c2 100644 --- a/arch/arm/mach-k3/Makefile +++ b/arch/arm/mach-k3/Makefile @@ -7,4 +7,5 @@ obj-$(CONFIG_SOC_K3_AM6) += am6_init.o obj-$(CONFIG_ARM64) += arm64-mmu.o obj-$(CONFIG_CPU_V7R) += r5_mpu.o lowlevel_init.o obj-$(CONFIG_TI_SECURE_DEVICE) += security.o +obj-$(CONFIG_K3_LOAD_SYSFW) += sysfw-loader.o obj-y += common.o diff --git a/arch/arm/mach-k3/include/mach/sysfw-loader.h b/arch/arm/mach-k3/include/mach/sysfw-loader.h new file mode 100644 index 0000000000..36eb265348 --- /dev/null +++ b/arch/arm/mach-k3/include/mach/sysfw-loader.h @@ -0,0 +1,12 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ + * Andreas Dannenberg + */ + +#ifndef _SYSFW_LOADER_H_ +#define _SYSFW_LOADER_H_ + +void k3_sysfw_loader(void (*config_pm_done_callback)(void)); + +#endif diff --git a/arch/arm/mach-k3/sysfw-loader.c b/arch/arm/mach-k3/sysfw-loader.c new file mode 100644 index 0000000000..a222266c27 --- /dev/null +++ b/arch/arm/mach-k3/sysfw-loader.c @@ -0,0 +1,263 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * K3: System Firmware Loader + * + * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ + * Andreas Dannenberg + */ + +#include +#include +#include +#include +#include +#include + +/* Name of the FIT image nodes for SYSFW and its config data */ +#define SYSFW_FIRMWARE "sysfw.bin" +#define SYSFW_CFG_BOARD "board-cfg.bin" +#define SYSFW_CFG_PM "pm-cfg.bin" +#define SYSFW_CFG_RM "rm-cfg.bin" +#define SYSFW_CFG_SEC "sec-cfg.bin" + +#ifdef CONFIG_SPL_BUILD + +static bool sysfw_loaded; +static void *sysfw_load_address; + +/* + * Populate SPL hook to override the default load address used by the SPL + * loader function with a custom address for SYSFW loading. + */ +struct image_header *spl_get_load_buffer(ssize_t offset, size_t size) +{ + if (sysfw_loaded) + return (struct image_header *)(CONFIG_SYS_TEXT_BASE + offset); + else if (sysfw_load_address) + return sysfw_load_address; + else + panic("SYSFW load address not defined!"); +} + +/* + * Populate SPL hook to skip the default SPL loader FIT post-processing steps + * during SYSFW loading and return to the calling function so we can perform + * our own custom processing. + */ +bool spl_load_simple_fit_skip_processing(void) +{ + return !sysfw_loaded; +} + +static int fit_get_data_by_name(const void *fit, int images, const char *name, + const void **addr, size_t *size) +{ + int node_offset; + + node_offset = fdt_subnode_offset(fit, images, name); + if (node_offset < 0) + return -ENOENT; + + return fit_image_get_data(fit, node_offset, addr, size); +} + +static void k3_sysfw_load_using_fit(void *fit) +{ + int images; + const void *sysfw_addr; + size_t sysfw_size; + int ret; + + /* Find the node holding the images information */ + images = fdt_path_offset(fit, FIT_IMAGES_PATH); + if (images < 0) + panic("Cannot find /images node (%d)\n", images); + + /* Extract System Firmware (SYSFW) image from FIT */ + ret = fit_get_data_by_name(fit, images, SYSFW_FIRMWARE, + &sysfw_addr, &sysfw_size); + if (ret < 0) + panic("Error accessing %s node in FIT (%d)\n", SYSFW_FIRMWARE, + ret); + + /* + * Start up system controller firmware + * + * It is assumed that remoteproc device 0 is the corresponding + * system-controller that runs SYSFW. Make sure DT reflects the same. + */ + ret = rproc_dev_init(0); + if (ret) + panic("rproc failed to be initialized (%d)\n", ret); + + ret = rproc_load(0, (ulong)sysfw_addr, (ulong)sysfw_size); + if (ret) + panic("Firmware failed to start on rproc (%d)\n", ret); + + ret = rproc_start(0); + if (ret) + panic("Firmware init failed on rproc (%d)\n", ret); +} + +static void k3_sysfw_configure_using_fit(void *fit, + struct ti_sci_handle *ti_sci) +{ + struct ti_sci_board_ops *board_ops = &ti_sci->ops.board_ops; + int images; + const void *cfg_fragment_addr; + size_t cfg_fragment_size; + int ret; + + /* Find the node holding the images information */ + images = fdt_path_offset(fit, FIT_IMAGES_PATH); + if (images < 0) + panic("Cannot find /images node (%d)\n", images); + + /* Extract board configuration from FIT */ + ret = fit_get_data_by_name(fit, images, SYSFW_CFG_BOARD, + &cfg_fragment_addr, &cfg_fragment_size); + if (ret < 0) + panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_BOARD, + ret); + + /* Apply board configuration to SYSFW */ + ret = board_ops->board_config(ti_sci, + (u64)(u32)cfg_fragment_addr, + (u32)cfg_fragment_size); + if (ret) + panic("Failed to set board configuration (%d)\n", ret); + + /* Extract power/clock (PM) specific configuration from FIT */ + ret = fit_get_data_by_name(fit, images, SYSFW_CFG_PM, + &cfg_fragment_addr, &cfg_fragment_size); + if (ret < 0) + panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_PM, + ret); + + /* Apply power/clock (PM) specific configuration to SYSFW */ + ret = board_ops->board_config_pm(ti_sci, + (u64)(u32)cfg_fragment_addr, + (u32)cfg_fragment_size); + if (ret) + panic("Failed to set board PM configuration (%d)\n", ret); + + /* Extract resource management (RM) specific configuration from FIT */ + ret = fit_get_data_by_name(fit, images, SYSFW_CFG_RM, + &cfg_fragment_addr, &cfg_fragment_size); + if (ret < 0) + panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_RM, + ret); + + /* Apply resource management (RM) configuration to SYSFW */ + ret = board_ops->board_config_rm(ti_sci, + (u64)(u32)cfg_fragment_addr, + (u32)cfg_fragment_size); + if (ret) + panic("Failed to set board RM configuration (%d)\n", ret); + + /* Extract security specific configuration from FIT */ + ret = fit_get_data_by_name(fit, images, SYSFW_CFG_SEC, + &cfg_fragment_addr, &cfg_fragment_size); + if (ret < 0) + panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_SEC, + ret); + + /* Apply security configuration to SYSFW */ + ret = board_ops->board_config_security(ti_sci, + (u64)(u32)cfg_fragment_addr, + (u32)cfg_fragment_size); + if (ret) + panic("Failed to set board security configuration (%d)\n", + ret); +} + +void k3_sysfw_loader(void (*config_pm_done_callback)(void)) +{ + struct spl_image_info spl_image = { 0 }; + struct spl_boot_device bootdev = { 0 }; + struct ti_sci_handle *ti_sci; + int ret; + + /* Reserve a block of aligned memory for loading the SYSFW image */ + sysfw_load_address = memalign(ARCH_DMA_MINALIGN, + CONFIG_K3_SYSFW_IMAGE_SIZE_MAX); + if (!sysfw_load_address) + panic("Error allocating %u bytes of memory for SYSFW image\n", + CONFIG_K3_SYSFW_IMAGE_SIZE_MAX); + + debug("%s: allocated %u bytes at 0x%p\n", __func__, + CONFIG_K3_SYSFW_IMAGE_SIZE_MAX, sysfw_load_address); + + /* Set load address for legacy modes that bypass spl_get_load_buffer */ + spl_image.load_addr = (uintptr_t)sysfw_load_address; + + bootdev.boot_device = spl_boot_device(); + + /* Load combined System Controller firmware and config data image */ + switch (bootdev.boot_device) { +#if CONFIG_IS_ENABLED(MMC_SUPPORT) + case BOOT_DEVICE_MMC1: + case BOOT_DEVICE_MMC2: + case BOOT_DEVICE_MMC2_2: + ret = spl_mmc_load(&spl_image, &bootdev, +#ifdef CONFIG_K3_SYSFW_IMAGE_NAME + CONFIG_K3_SYSFW_IMAGE_NAME, +#else + NULL, +#endif +#ifdef CONFIG_K3_SYSFW_IMAGE_MMCSD_RAW_MODE_PART + CONFIG_K3_SYSFW_IMAGE_MMCSD_RAW_MODE_PART, +#else + 0, +#endif +#ifdef CONFIG_K3_SYSFW_IMAGE_MMCSD_RAW_MODE_SECT + CONFIG_K3_SYSFW_IMAGE_MMCSD_RAW_MODE_SECT); +#else + 0); +#endif + break; +#endif + default: + panic("Loading SYSFW image from device %u not supported!\n", + bootdev.boot_device); + } + + if (ret) + panic("Error %d occurred during loading SYSFW image!\n", ret); + + /* + * Now that SYSFW got loaded set helper flag to restore regular SPL + * loader behavior so we can later boot into the next stage as expected. + */ + sysfw_loaded = true; + + /* Ensure the SYSFW image is in FIT format */ + if (image_get_magic((const image_header_t *)sysfw_load_address) != + FDT_MAGIC) + panic("SYSFW image not in FIT format!\n"); + + /* Extract and start SYSFW */ + k3_sysfw_load_using_fit(sysfw_load_address); + + /* Get handle for accessing SYSFW services */ + ti_sci = get_ti_sci_handle(); + + /* Parse and apply the different SYSFW configuration fragments */ + k3_sysfw_configure_using_fit(sysfw_load_address, ti_sci); + + /* + * Now that all clocks and PM aspects are setup, invoke a user- + * provided callback function. Usually this callback would be used + * to setup or re-configure the U-Boot console UART. + */ + if (config_pm_done_callback) + config_pm_done_callback(); + + /* Output System Firmware version info */ + printf("SYSFW ABI: %d.%d (firmware rev 0x%04x '%.*s')\n", + ti_sci->version.abi_major, ti_sci->version.abi_minor, + ti_sci->version.firmware_revision, + sizeof(ti_sci->version.firmware_description), + ti_sci->version.firmware_description); +} +#endif -- 2.17.1