From mboxrd@z Thu Jan 1 00:00:00 1970 From: Tom Rini Date: Wed, 8 May 2019 18:37:38 -0400 Subject: [U-Boot] Pull request: u-boot-net.git master In-Reply-To: References: <201905072215.x47MFDuv034108@osboxes.amer.corp.natinst.com> Message-ID: <20190508223738.GU25571@bill-the-cat> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de On Wed, May 08, 2019 at 10:24:29PM +0000, Joe Hershberger wrote: > On Tue, May 7, 2019 at 5:15 PM Joe Hershberger wrote: > > > > Hi Tom, > > > > The following changes since commit 8d7f06bbbef16f172cd5e9c4923cdcebe16b8980: > > > > I rebased on your master and built for BB Black. DHCP seems to work fine. > > MLO also now fits again. > > > > Merge branch 'master' of git://git.denx.de/u-boot-sh (2019-05-07 09:38:00 -0400) > > > > are available in the git repository at: > > > > git://git.denx.de/u-boot-net.git master > > > > for you to fetch changes up to 8d0c6858455e89b089222a08d55ff711681ca011: > > > > net: phy: micrel: Find Micrel PHY node correctly (2019-05-07 14:51:55 -0500) > > > > ---------------------------------------------------------------- > > Carlo Caione (4): > > net: phy: Add generic helpers to access MMD PHY registers > > net: phy: ti: use generic helpers to access MMD registers > > cmd: mdio: Switch to generic helpers when accessing the registers > > net: phy: realtek: Introduce quirk to mark RXC not stoppable > > > > James Byrne (2): > > net: phy: micrel: Use correct skew values on KSZ9021 > > net: phy: micrel: Find Micrel PHY node correctly > > > > Murali Karicheri (2): > > ARM: k2g-gp-evm: update to rgmii pinmux configuration > > ARM: k2g-ice: Add pinmux support for rgmii interface > > > > Pankaj Bansal (1): > > drivers: net: ldpaa_eth: fix resource leak > > > > Siva Durga Prasad Paladugu (2): > > net: phy: Reloc next and prev pointers inside phy_drivers > > net: phy: Fix return value check phy_probe > > > > Valentin-catalin Neacsu (1): > > net: phy: aquantia: Set only autoneg on in register 4.c441 > > > > Vladimir Oltean (6): > > net: phy: ar803x: Address packet drops at low traffic rate due to SmartEEE feature > > net: phy: ar803x: Make RGMII Tx delays actually configurable for AR8035 > > net: phy: ar803x: Use common functions for RGMII internal delays > > net: phy: ar803x: Clarify the configuration of the CLK_25M output pin > > net: phy: ar803x: Explicitly disable RGMII delays > > Tom, this [1] is the patch that is breaking the evm. It doesn't affect > BB Black because it uses an SMSC phy, where as this evm uses an > AR8031/AR8033. > > Is it possible the device tree [2] is wrong for the board? It lists > 'phy-mode = "rgmii-txid";', so that means that with this patch the RX > delay is now being disabled. > > Any thoughts, Vladimir? > > Thanks, > -Joe > > [1] b3224e0f7e - "net: phy: ar803x: Explicitly disable RGMII delays" > [2] arch/arm/dts/am335x-evm.dts Thanks for tracking this down. I believe the DTS is right as it matches the kernel in this regard. That said, it's the Bone which has the schematic available and not the EVM so I can't point at that for further digging. -- Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: