From mboxrd@z Thu Jan 1 00:00:00 1970 From: Fabio Estevam Date: Tue, 21 May 2019 10:37:54 -0300 Subject: [U-Boot] [PATCH v2 3/3] mx6sabresd: Remove U-Boot proper mmc initialization In-Reply-To: <20190521133754.29553-1-festevam@gmail.com> References: <20190521133754.29553-1-festevam@gmail.com> Message-ID: <20190521133754.29553-3-festevam@gmail.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de After the conversion to DM there is no need to have mmc initialization code inside U-Boot proper. Remove the unneeded code. Signed-off-by: Fabio Estevam --- Changes since v1: - None board/freescale/mx6sabresd/mx6sabresd.c | 44 ------------------------- 1 file changed, 44 deletions(-) diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 385a18e923..cdfc5ff77f 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -287,49 +287,6 @@ int board_mmc_getcd(struct mmc *mmc) int board_mmc_init(bd_t *bis) { -#ifndef CONFIG_SPL_BUILD - int ret; - int i; - - /* - * According to the board_mmc_init() the following map is done: - * (U-Boot device node) (Physical Port) - * mmc0 SD2 - * mmc1 SD3 - * mmc2 eMMC - */ - for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { - switch (i) { - case 0: - SETUP_IOMUX_PADS(usdhc2_pads); - gpio_request(USDHC2_CD_GPIO, "USDHC2 CD"); - gpio_direction_input(USDHC2_CD_GPIO); - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); - break; - case 1: - SETUP_IOMUX_PADS(usdhc3_pads); - gpio_request(USDHC3_CD_GPIO, "USDHC3 CD"); - gpio_direction_input(USDHC3_CD_GPIO); - usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); - break; - case 2: - SETUP_IOMUX_PADS(usdhc4_pads); - usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); - break; - default: - printf("Warning: you configured more USDHC controllers" - "(%d) then supported by the board (%d)\n", - i + 1, CONFIG_SYS_FSL_USDHC_NUM); - return -EINVAL; - } - - ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); - if (ret) - return ret; - } - - return 0; -#else struct src *psrc = (struct src *)SRC_BASE_ADDR; unsigned reg = readl(&psrc->sbmr1) >> 11; /* @@ -363,7 +320,6 @@ int board_mmc_init(bd_t *bis) } return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); -#endif } #endif -- 2.17.1