[PATCH 1/6] ARM: dts: imx6qdl: Enable SNVS power key according to board design

[PATCH 1/6] ARM: dts: imx6qdl: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 4 ++++
 arch/arm/boot/dts/imx6qdl.dtsi         | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 11103a4..71ca76a 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -761,6 +761,10 @@
 	status = "okay";
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &ssi2 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 929fc7d..4b80193 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -841,6 +841,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 
 				snvs_lpgpr: snvs-lpgpr {
-- 
2.7.4

[PATCH 1/6] ARM: dts: imx6qdl: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 4 ++++
 arch/arm/boot/dts/imx6qdl.dtsi         | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 11103a4..71ca76a 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -761,6 +761,10 @@
 	status = "okay";
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &ssi2 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 929fc7d..4b80193 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -841,6 +841,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 
 				snvs_lpgpr: snvs-lpgpr {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/6] ARM: dts: imx6sx: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6sx-sdb-reva.dts | 4 ++++
 arch/arm/boot/dts/imx6sx-sdb.dts      | 4 ++++
 arch/arm/boot/dts/imx6sx.dtsi         | 1 +
 3 files changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
index 5b3d6c10..f1830ed 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-reva.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
@@ -166,3 +166,7 @@
 &reg_vdd2p5 {
 	vin-supply = <&vgen6_reg>;
 };
+
+&snvs_pwrkey {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts
index 10f6da8..a8ee708 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -153,3 +153,7 @@
 	/* Transceiver EN/STBY is active low on RevB board */
 	gpio = <&gpio4 27 GPIO_ACTIVE_LOW>;
 };
+
+&snvs_pwrkey {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
index bbdfdd8..bb25add 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -738,6 +738,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 			};
 
-- 
2.7.4

[PATCH 2/6] ARM: dts: imx6sx: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6sx-sdb-reva.dts | 4 ++++
 arch/arm/boot/dts/imx6sx-sdb.dts      | 4 ++++
 arch/arm/boot/dts/imx6sx.dtsi         | 1 +
 3 files changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
index 5b3d6c10..f1830ed 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-reva.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
@@ -166,3 +166,7 @@
 &reg_vdd2p5 {
 	vin-supply = <&vgen6_reg>;
 };
+
+&snvs_pwrkey {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts
index 10f6da8..a8ee708 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -153,3 +153,7 @@
 	/* Transceiver EN/STBY is active low on RevB board */
 	gpio = <&gpio4 27 GPIO_ACTIVE_LOW>;
 };
+
+&snvs_pwrkey {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
index bbdfdd8..bb25add 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -738,6 +738,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 			};
 
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/6] ARM: dts: imx6ul: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 4 ++++
 arch/arm/boot/dts/imx6ul.dtsi           | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
index 9207d5d..cbe61b6 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
@@ -238,6 +238,10 @@
 	status = "okay";
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &tsc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_tsc>;
diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
index fc388b8..0c51439 100644
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul.dtsi
@@ -650,6 +650,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 
 				snvs_lpgpr: snvs-lpgpr {
-- 
2.7.4

[PATCH 3/6] ARM: dts: imx6ul: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 4 ++++
 arch/arm/boot/dts/imx6ul.dtsi           | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
index 9207d5d..cbe61b6 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
@@ -238,6 +238,10 @@
 	status = "okay";
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &tsc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_tsc>;
diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
index fc388b8..0c51439 100644
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul.dtsi
@@ -650,6 +650,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 
 				snvs_lpgpr: snvs-lpgpr {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/6] ARM: dts: imx6sll: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6sll-evk.dts | 4 ++++
 arch/arm/boot/dts/imx6sll.dtsi    | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts
index 78809ea..61aa074 100644
--- a/arch/arm/boot/dts/imx6sll-evk.dts
+++ b/arch/arm/boot/dts/imx6sll-evk.dts
@@ -269,6 +269,10 @@
 	vin-supply = <&sw2_reg>;
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi
index 1b4899f..4384023 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/imx6sll.dtsi
@@ -576,6 +576,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 			};
 
-- 
2.7.4

[PATCH 4/6] ARM: dts: imx6sll: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6sll-evk.dts | 4 ++++
 arch/arm/boot/dts/imx6sll.dtsi    | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts
index 78809ea..61aa074 100644
--- a/arch/arm/boot/dts/imx6sll-evk.dts
+++ b/arch/arm/boot/dts/imx6sll-evk.dts
@@ -269,6 +269,10 @@
 	vin-supply = <&sw2_reg>;
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi
index 1b4899f..4384023 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/imx6sll.dtsi
@@ -576,6 +576,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 			};
 
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5/6] ARM: dts: imx7s: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx7d-sdb.dts | 4 ++++
 arch/arm/boot/dts/imx7s.dtsi    | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index a5365b8..869efbc 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -387,6 +387,10 @@
 	vin-supply = <&sw2_reg>;
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi
index d8b4eb6..479be1f 100644
--- a/arch/arm/boot/dts/imx7s.dtsi
+++ b/arch/arm/boot/dts/imx7s.dtsi
@@ -609,6 +609,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 			};
 
-- 
2.7.4

[PATCH 5/6] ARM: dts: imx7s: Enable SNVS power key according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx7d-sdb.dts | 4 ++++
 arch/arm/boot/dts/imx7s.dtsi    | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index a5365b8..869efbc 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -387,6 +387,10 @@
 	vin-supply = <&sw2_reg>;
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi
index d8b4eb6..479be1f 100644
--- a/arch/arm/boot/dts/imx7s.dtsi
+++ b/arch/arm/boot/dts/imx7s.dtsi
@@ -609,6 +609,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 			};
 
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 6/6] ARM: dts: imx6sll: Enable SNVS poweroff according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS poweroff depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up to external PMIC.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6sll-evk.dts | 4 ++++
 arch/arm/boot/dts/imx6sll.dtsi    | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts
index 61aa074..3e1d32f 100644
--- a/arch/arm/boot/dts/imx6sll-evk.dts
+++ b/arch/arm/boot/dts/imx6sll-evk.dts
@@ -269,6 +269,10 @@
 	vin-supply = <&sw2_reg>;
 };
 
+&snvs_poweroff {
+	status = "okay";
+};
+
 &snvs_pwrkey {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi
index 4384023..b0a77ff 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/imx6sll.dtsi
@@ -568,6 +568,7 @@
 					regmap = <&snvs>;
 					offset = <0x38>;
 					mask = <0x61>;
+					status = "disabled";
 				};
 
 				snvs_pwrkey: snvs-powerkey {
-- 
2.7.4

[PATCH 6/6] ARM: dts: imx6sll: Enable SNVS poweroff according to board design

[Anson.Huang]

From: Anson Huang <Anson.Huang@nxp.com>

The SNVS poweroff depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up to external PMIC.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx6sll-evk.dts | 4 ++++
 arch/arm/boot/dts/imx6sll.dtsi    | 1 +
 2 files changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts
index 61aa074..3e1d32f 100644
--- a/arch/arm/boot/dts/imx6sll-evk.dts
+++ b/arch/arm/boot/dts/imx6sll-evk.dts
@@ -269,6 +269,10 @@
 	vin-supply = <&sw2_reg>;
 };
 
+&snvs_poweroff {
+	status = "okay";
+};
+
 &snvs_pwrkey {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi
index 4384023..b0a77ff 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/imx6sll.dtsi
@@ -568,6 +568,7 @@
 					regmap = <&snvs>;
 					offset = <0x38>;
 					mask = <0x61>;
+					status = "disabled";
 				};
 
 				snvs_pwrkey: snvs-powerkey {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/6] ARM: dts: imx6qdl: Enable SNVS power key according to board design

[Shawn Guo]

On Thu, Jun 13, 2019 at 11:35:22AM +0800, Anson.Huang@nxp.com wrote:
> From: Anson Huang <Anson.Huang@nxp.com>
> 
> The SNVS power key depends on board design, by default it should
> be disabled in SoC DT and ONLY be enabled on board DT if it is
> wired up.
> 
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Applied all, thanks.

Re: [PATCH 1/6] ARM: dts: imx6qdl: Enable SNVS power key according to board design

[Shawn Guo]

On Thu, Jun 13, 2019 at 11:35:22AM +0800, Anson.Huang@nxp.com wrote:
> From: Anson Huang <Anson.Huang@nxp.com>
> 
> The SNVS power key depends on board design, by default it should
> be disabled in SoC DT and ONLY be enabled on board DT if it is
> wired up.
> 
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Applied all, thanks.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel