All of lore.kernel.org
 help / color / mirror / Atom feed
From: Philippe Schenker <dev@pschenker.ch>
To: marcel.ziswiler@toradex.com, max.krummenacher@toradex.com,
	stefan@agner.ch, devicetree@vger.kernel.org,
	Rob Herring <robh+dt@kernel.org>, Shawn Guo <shawnguo@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>,
	Fabio Estevam <festevam@gmail.com>,
	linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	NXP Linux Team <linux-imx@nxp.com>,
	Sascha Hauer <s.hauer@pengutronix.de>
Subject: [PATCH 08/22] ARM: dts: imx7-colibri: Add touch controllers
Date: Tue, 30 Jul 2019 16:46:35 +0200	[thread overview]
Message-ID: <20190730144649.19022-9-dev@pschenker.ch> (raw)
In-Reply-To: <20190730144649.19022-1-dev@pschenker.ch>

From: Philippe Schenker <philippe.schenker@toradex.com>

Add atmel mxt multitouch controller and TouchRevolution multitouch
controller which are connected over an I2C bus.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
---

 arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi | 37 +++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
index d4dbc4fc1adf..f6cbbe876532 100644
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
@@ -145,6 +145,34 @@
 &i2c4 {
 	status = "okay";
 
+	/*
+	 * the PCAPs use SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2,
+	 * pwm3. so if you enable one of the PCAP controllers disable the pwms
+	 */
+	atmel_mxt_ts: atmel_mxt_ts@4a {
+		compatible = "atmel,maxtouch";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiotouch>;
+		reg = <0x4a>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
+		reset-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; /* SODIMM 30 */
+		status = "disabled";
+	};
+
+	touch: touchrevf0710a@10 {
+		compatible = "touchrevolution,fusion-f0710a";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiotouch>;
+		reg = <0x10>;
+			/* SODIMM 28, Pen down interrupt */
+		gpios = <&gpio1 9 GPIO_ACTIVE_HIGH
+			/* SODIMM 30, Reset interrupt */
+			 &gpio1 10 GPIO_ACTIVE_LOW
+			>;
+		status = "disabled";
+	};
+
 	/* M41T0M6 real time clock on carrier board */
 	rtc: m41t0m6@68 {
 		compatible = "st,m41t0";
@@ -200,3 +228,12 @@
 	vmmc-supply = <&reg_3v3>;
 	status = "okay";
 };
+
+&iomuxc {
+	pinctrl_gpiotouch: touchgpios {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x74
+			MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x14
+		>;
+	};
+};
-- 
2.22.0


WARNING: multiple messages have this Message-ID
From: Philippe Schenker <dev@pschenker.ch>
To: marcel.ziswiler@toradex.com, max.krummenacher@toradex.com,
	stefan@agner.ch, devicetree@vger.kernel.org,
	Rob Herring <robh+dt@kernel.org>, Shawn Guo <shawnguo@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>,
	linux-kernel@vger.kernel.org,
	Philippe Schenker <philippe.schenker@toradex.com>,
	NXP Linux Team <linux-imx@nxp.com>,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	Fabio Estevam <festevam@gmail.com>,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH 08/22] ARM: dts: imx7-colibri: Add touch controllers
Date: Tue, 30 Jul 2019 16:46:35 +0200	[thread overview]
Message-ID: <20190730144649.19022-9-dev@pschenker.ch> (raw)
In-Reply-To: <20190730144649.19022-1-dev@pschenker.ch>

From: Philippe Schenker <philippe.schenker@toradex.com>

Add atmel mxt multitouch controller and TouchRevolution multitouch
controller which are connected over an I2C bus.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
---

 arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi | 37 +++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
index d4dbc4fc1adf..f6cbbe876532 100644
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
@@ -145,6 +145,34 @@
 &i2c4 {
 	status = "okay";
 
+	/*
+	 * the PCAPs use SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2,
+	 * pwm3. so if you enable one of the PCAP controllers disable the pwms
+	 */
+	atmel_mxt_ts: atmel_mxt_ts@4a {
+		compatible = "atmel,maxtouch";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiotouch>;
+		reg = <0x4a>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
+		reset-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; /* SODIMM 30 */
+		status = "disabled";
+	};
+
+	touch: touchrevf0710a@10 {
+		compatible = "touchrevolution,fusion-f0710a";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiotouch>;
+		reg = <0x10>;
+			/* SODIMM 28, Pen down interrupt */
+		gpios = <&gpio1 9 GPIO_ACTIVE_HIGH
+			/* SODIMM 30, Reset interrupt */
+			 &gpio1 10 GPIO_ACTIVE_LOW
+			>;
+		status = "disabled";
+	};
+
 	/* M41T0M6 real time clock on carrier board */
 	rtc: m41t0m6@68 {
 		compatible = "st,m41t0";
@@ -200,3 +228,12 @@
 	vmmc-supply = <&reg_3v3>;
 	status = "okay";
 };
+
+&iomuxc {
+	pinctrl_gpiotouch: touchgpios {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x74
+			MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x14
+		>;
+	};
+};
-- 
2.22.0

WARNING: multiple messages have this Message-ID
From: Philippe Schenker <dev@pschenker.ch>
To: marcel.ziswiler@toradex.com, max.krummenacher@toradex.com,
	stefan@agner.ch, devicetree@vger.kernel.org,
	Rob Herring <robh+dt@kernel.org>, Shawn Guo <shawnguo@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>,
	linux-kernel@vger.kernel.org,
	Philippe Schenker <philippe.schenker@toradex.com>,
	NXP Linux Team <linux-imx@nxp.com>,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	Fabio Estevam <festevam@gmail.com>,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH 08/22] ARM: dts: imx7-colibri: Add touch controllers
Date: Tue, 30 Jul 2019 16:46:35 +0200	[thread overview]
Message-ID: <20190730144649.19022-9-dev@pschenker.ch> (raw)
In-Reply-To: <20190730144649.19022-1-dev@pschenker.ch>

From: Philippe Schenker <philippe.schenker@toradex.com>

Add atmel mxt multitouch controller and TouchRevolution multitouch
controller which are connected over an I2C bus.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
---

 arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi | 37 +++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
index d4dbc4fc1adf..f6cbbe876532 100644
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
@@ -145,6 +145,34 @@
 &i2c4 {
 	status = "okay";
 
+	/*
+	 * the PCAPs use SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2,
+	 * pwm3. so if you enable one of the PCAP controllers disable the pwms
+	 */
+	atmel_mxt_ts: atmel_mxt_ts@4a {
+		compatible = "atmel,maxtouch";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiotouch>;
+		reg = <0x4a>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
+		reset-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; /* SODIMM 30 */
+		status = "disabled";
+	};
+
+	touch: touchrevf0710a@10 {
+		compatible = "touchrevolution,fusion-f0710a";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiotouch>;
+		reg = <0x10>;
+			/* SODIMM 28, Pen down interrupt */
+		gpios = <&gpio1 9 GPIO_ACTIVE_HIGH
+			/* SODIMM 30, Reset interrupt */
+			 &gpio1 10 GPIO_ACTIVE_LOW
+			>;
+		status = "disabled";
+	};
+
 	/* M41T0M6 real time clock on carrier board */
 	rtc: m41t0m6@68 {
 		compatible = "st,m41t0";
@@ -200,3 +228,12 @@
 	vmmc-supply = <&reg_3v3>;
 	status = "okay";
 };
+
+&iomuxc {
+	pinctrl_gpiotouch: touchgpios {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x74
+			MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x14
+		>;
+	};
+};
-- 
2.22.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2019-07-30 15:11 UTC|newest]

Thread overview: 84+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-30 14:46 [PATCH 00/22] This patchset holds some common changes that were never upstreamed Philippe Schenker
2019-07-30 14:46 ` [PATCH 01/22] ARM: dts: imx7-colibri: make sure module supplies are always on Philippe Schenker
2019-07-30 14:46 ` [PATCH 02/22] ARM: dts: imx7-colibri: disable HS400 Philippe Schenker
2019-07-30 14:46 ` [PATCH 03/22] ARM: dts: imx7-colibri: prepare module device tree for FlexCAN Philippe Schenker
2019-07-30 14:46 ` [PATCH 04/22] ARM: dts: imx7-colibri: Add sleep mode to ethernet Philippe Schenker
2019-07-30 14:46 ` [PATCH 05/22] ARM: dts: add recovery for I2C for iMX7 Philippe Schenker
2019-07-30 14:46 ` [PATCH 06/22] ARM: dts: imx7-colibri: add GPIO wakeup key Philippe Schenker
2019-07-30 14:46 ` [PATCH 07/22] ARM: dts: imx7-colibri: fix 1.8V/UHS support Philippe Schenker
2019-07-30 14:46 ` Philippe Schenker [this message]
2019-07-30 14:46 ` [PATCH 09/22] ARM: dts: imx6qdl-colibri: add phy to fec Philippe Schenker
2019-07-30 14:46 ` [PATCH 10/22] ARM: dts: imx6qdl-colibri: Add missing pin declaration in iomuxc Philippe Schenker
2019-07-30 14:46 ` [PATCH 11/22] ARM: dts: imx6: Add sleep state to can interfaces Philippe Schenker
2019-07-31  7:14   ` Michal Vokáč
2019-07-31 11:13     ` Philippe Schenker
2019-07-30 14:46 ` [PATCH 12/22] ARM: dts: imx6: Add touchscreens used on Toradex eval boards Philippe Schenker
2019-07-30 20:46   ` Fabio Estevam
2019-07-31  6:43     ` Philippe Schenker
2019-07-31  6:54       ` Michal Vokáč
2019-07-30 14:46 ` [PATCH 13/22] ARM: dts: colibri-imx6: Add missing pinmuxing to Toradex eval board Philippe Schenker
2019-07-31  7:09   ` Michal Vokáč
2019-07-30 14:46 ` [PATCH 14/22] ARM: dts: apalis-imx6: Add some example I2C devices Philippe Schenker
2019-07-30 20:53   ` Fabio Estevam
2019-07-31 11:36     ` Philippe Schenker
2019-07-30 14:46 ` [PATCH 15/22] ARM: dts: apalis-imx6: Add some optional " Philippe Schenker
2019-07-30 20:43   ` Fabio Estevam
2019-07-31 11:37     ` Philippe Schenker
2019-07-30 14:46 ` [PATCH 16/22] ARM: dts: imx6ull-colibri: Add sleep mode to fec Philippe Schenker
2019-07-30 14:46 ` [PATCH 17/22] ARM: dts: imx6ull-colibri: reduce v_batt current in power off Philippe Schenker
2019-07-30 14:46 ` [PATCH 18/22] ARM: dts: imx6ull-colibri: Add watchdog Philippe Schenker
2019-07-30 14:46 ` [PATCH 19/22] ARM: dts: imx6ull: improve can templates Philippe Schenker
2019-07-30 14:46 ` [PATCH 20/22] ARM: dts: imx6ull-colibri: Add general wakeup key used on Colibri Philippe Schenker
2019-07-30 14:46 ` [PATCH 21/22] ARM: dts: imx6/7-colibri: switch dr_mode to otg Philippe Schenker
2019-07-30 14:46 ` [PATCH 22/22] ARM: dts: imx6ull-colibri: Add touchscreens used with Eval Board Philippe Schenker

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190730144649.19022-9-dev@pschenker.ch \
    --to=dev@pschenker.ch \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=marcel.ziswiler@toradex.com \
    --cc=mark.rutland@arm.com \
    --cc=max.krummenacher@toradex.com \
    --cc=philippe.schenker@toradex.com \
    --cc=robh+dt@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    --cc=stefan@agner.ch \
    --subject='Re: [PATCH 08/22] ARM: dts: imx7-colibri: Add touch controllers' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.