From: Russell King - ARM Linux admin <linux@armlinux.org.uk>
To: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>, Chris Snook <chris.snook@gmail.com>,
Florian Fainelli <f.fainelli@gmail.com>,
James Hogan <jhogan@kernel.org>, Jay Cliburn <jcliburn@gmail.com>,
Mark Rutland <mark.rutland@arm.com>,
Paul Burton <paul.burton@mips.com>,
Ralf Baechle <ralf@linux-mips.org>,
Rob Herring <robh+dt@kernel.org>,
Vivien Didelot <vivien.didelot@gmail.com>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
"David S. Miller" <davem@davemloft.net>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, linux-mips@vger.kernel.org
Subject: Re: [PATCH v2 1/5] net: ag71xx: port to phylink
Date: Fri, 18 Oct 2019 10:53:49 +0100 [thread overview]
Message-ID: <20191018095349.GF25745@shell.armlinux.org.uk> (raw)
In-Reply-To: <20191018093929.19299-2-o.rempel@pengutronix.de>
Hi,
On Fri, Oct 18, 2019 at 11:39:25AM +0200, Oleksij Rempel wrote:
> The port to phylink was done as close as possible to initial
> functionality.
> Theoretically this HW can support flow control, practically seems to be not
> enough to just enable it. So, more work should be done.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> drivers/net/ethernet/atheros/Kconfig | 2 +-
> drivers/net/ethernet/atheros/ag71xx.c | 146 +++++++++++++++-----------
> 2 files changed, 87 insertions(+), 61 deletions(-)
>
> diff --git a/drivers/net/ethernet/atheros/Kconfig b/drivers/net/ethernet/atheros/Kconfig
> index 0058051ba925..2720bde5034e 100644
> --- a/drivers/net/ethernet/atheros/Kconfig
> +++ b/drivers/net/ethernet/atheros/Kconfig
> @@ -20,7 +20,7 @@ if NET_VENDOR_ATHEROS
> config AG71XX
> tristate "Atheros AR7XXX/AR9XXX built-in ethernet mac support"
> depends on ATH79
> - select PHYLIB
> + select PHYLINK
> help
> If you wish to compile a kernel for AR7XXX/91XXX and enable
> ethernet support, then you should always answer Y to this.
> diff --git a/drivers/net/ethernet/atheros/ag71xx.c b/drivers/net/ethernet/atheros/ag71xx.c
> index 1b1a09095c0d..4ad587d6a8e8 100644
> --- a/drivers/net/ethernet/atheros/ag71xx.c
> +++ b/drivers/net/ethernet/atheros/ag71xx.c
> @@ -32,6 +32,7 @@
> #include <linux/of_mdio.h>
> #include <linux/of_net.h>
> #include <linux/of_platform.h>
> +#include <linux/phylink.h>
> #include <linux/regmap.h>
> #include <linux/reset.h>
> #include <linux/clk.h>
> @@ -314,6 +315,8 @@ struct ag71xx {
> dma_addr_t stop_desc_dma;
>
> int phy_if_mode;
> + struct phylink *phylink;
> + struct phylink_config phylink_config;
>
> struct delayed_work restart_work;
> struct timer_list oom_timer;
> @@ -845,24 +848,20 @@ static void ag71xx_hw_start(struct ag71xx *ag)
> netif_wake_queue(ag->ndev);
> }
>
> -static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
> +static void ag71xx_mac_config(struct phylink_config *config, unsigned int mode,
> + const struct phylink_link_state *state)
> {
> - struct phy_device *phydev = ag->ndev->phydev;
> + struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
> u32 cfg2;
> u32 ifctl;
> u32 fifo5;
>
> - if (!phydev->link && update) {
> - ag71xx_hw_stop(ag);
> - return;
> - }
> -
> if (!ag71xx_is(ag, AR7100) && !ag71xx_is(ag, AR9130))
> ag71xx_fast_reset(ag);
>
> cfg2 = ag71xx_rr(ag, AG71XX_REG_MAC_CFG2);
> cfg2 &= ~(MAC_CFG2_IF_1000 | MAC_CFG2_IF_10_100 | MAC_CFG2_FDX);
> - cfg2 |= (phydev->duplex) ? MAC_CFG2_FDX : 0;
> + cfg2 |= (state->duplex) ? MAC_CFG2_FDX : 0;
>
> ifctl = ag71xx_rr(ag, AG71XX_REG_MAC_IFCTL);
> ifctl &= ~(MAC_IFCTL_SPEED);
> @@ -870,7 +869,7 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
> fifo5 = ag71xx_rr(ag, AG71XX_REG_FIFO_CFG5);
> fifo5 &= ~FIFO_CFG5_BM;
>
> - switch (phydev->speed) {
> + switch (state->speed) {
Please see the documentation for the mac_config() method in
include/linux/phylink.h wrt state->speed and state->duplex validity.
> case SPEED_1000:
> cfg2 |= MAC_CFG2_IF_1000;
> fifo5 |= FIFO_CFG5_BM;
> @@ -883,7 +882,6 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
> cfg2 |= MAC_CFG2_IF_10_100;
> break;
> default:
> - WARN(1, "not supported speed %i\n", phydev->speed);
> return;
> }
>
> @@ -897,58 +895,78 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
> ag71xx_wr(ag, AG71XX_REG_MAC_CFG2, cfg2);
> ag71xx_wr(ag, AG71XX_REG_FIFO_CFG5, fifo5);
> ag71xx_wr(ag, AG71XX_REG_MAC_IFCTL, ifctl);
> -
> - ag71xx_hw_start(ag);
> -
> - if (update)
> - phy_print_status(phydev);
> }
>
> -static void ag71xx_phy_link_adjust(struct net_device *ndev)
> +static void ag71xx_mac_validate(struct phylink_config *config,
> + unsigned long *supported,
> + struct phylink_link_state *state)
> {
> - struct ag71xx *ag = netdev_priv(ndev);
> + __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
> +
> + if (state->interface != PHY_INTERFACE_MODE_NA &&
> + state->interface != PHY_INTERFACE_MODE_GMII &&
> + state->interface != PHY_INTERFACE_MODE_MII) {
> + bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> + return;
> + }
> +
> + phylink_set(mask, MII);
> +
> + /* flow control is not supported */
>
> - ag71xx_link_adjust(ag, true);
> + phylink_set(mask, 10baseT_Half);
> + phylink_set(mask, 10baseT_Full);
> + phylink_set(mask, 100baseT_Half);
> + phylink_set(mask, 100baseT_Full);
> +
> + if (state->interface = PHY_INTERFACE_MODE_GMII) {
This is an assignment, is always true, and will produce a compiler
warning.
Please see the documentation for the validate() method in
include/linux/phylink.h wrt PHY_INTERFACE_MODE_NA handling.
Thanks.
> + phylink_set(mask, 1000baseT_Full);
> + phylink_set(mask, 1000baseX_Full);
> + }
> +
> + bitmap_and(supported, supported, mask,
> + __ETHTOOL_LINK_MODE_MASK_NBITS);
> + bitmap_and(state->advertising, state->advertising, mask,
> + __ETHTOOL_LINK_MODE_MASK_NBITS);
> }
>
> -static int ag71xx_phy_connect(struct ag71xx *ag)
> +static void ag71xx_mac_link_down(struct phylink_config *config,
> + unsigned int mode, phy_interface_t interface)
> {
> - struct device_node *np = ag->pdev->dev.of_node;
> - struct net_device *ndev = ag->ndev;
> - struct device_node *phy_node;
> - struct phy_device *phydev;
> - int ret;
> + struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
>
> - if (of_phy_is_fixed_link(np)) {
> - ret = of_phy_register_fixed_link(np);
> - if (ret < 0) {
> - netif_err(ag, probe, ndev, "Failed to register fixed PHY link: %d\n",
> - ret);
> - return ret;
> - }
> + ag71xx_hw_stop(ag);
> +}
>
> - phy_node = of_node_get(np);
> - } else {
> - phy_node = of_parse_phandle(np, "phy-handle", 0);
> - }
> +static void ag71xx_mac_link_up(struct phylink_config *config, unsigned int mode,
> + phy_interface_t interface,
> + struct phy_device *phy)
> +{
> + struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
>
> - if (!phy_node) {
> - netif_err(ag, probe, ndev, "Could not find valid phy node\n");
> - return -ENODEV;
> - }
> + ag71xx_hw_start(ag);
> +}
>
> - phydev = of_phy_connect(ag->ndev, phy_node, ag71xx_phy_link_adjust,
> - 0, ag->phy_if_mode);
> +static const struct phylink_mac_ops ag71xx_phylink_mac_ops = {
> + .validate = ag71xx_mac_validate,
> + .mac_config = ag71xx_mac_config,
> + .mac_link_down = ag71xx_mac_link_down,
> + .mac_link_up = ag71xx_mac_link_up,
> +};
>
> - of_node_put(phy_node);
> +static int ag71xx_phy_setup(struct ag71xx *ag)
> +{
> + struct phylink *phylink;
>
> - if (!phydev) {
> - netif_err(ag, probe, ndev, "Could not connect to PHY device\n");
> - return -ENODEV;
> - }
> + ag->phylink_config.dev = &ag->ndev->dev;
> + ag->phylink_config.type = PHYLINK_NETDEV;
>
> - phy_attached_info(phydev);
> + phylink = phylink_create(&ag->phylink_config, ag->pdev->dev.fwnode,
> + ag->phy_if_mode, &ag71xx_phylink_mac_ops);
> + if (IS_ERR(phylink))
> + return PTR_ERR(phylink);
>
> + ag->phylink = phylink;
> return 0;
> }
>
> @@ -1239,6 +1257,13 @@ static int ag71xx_open(struct net_device *ndev)
> unsigned int max_frame_len;
> int ret;
>
> + ret = phylink_of_phy_connect(ag->phylink, ag->pdev->dev.of_node, 0);
> + if (ret) {
> + netif_err(ag, link, ndev, "phylink_of_phy_connect filed with err: %i\n",
> + ret);
> + goto err;
> + }
> +
> max_frame_len = ag71xx_max_frame_len(ndev->mtu);
> ag->rx_buf_size =
> SKB_DATA_ALIGN(max_frame_len + NET_SKB_PAD + NET_IP_ALIGN);
> @@ -1251,11 +1276,7 @@ static int ag71xx_open(struct net_device *ndev)
> if (ret)
> goto err;
>
> - ret = ag71xx_phy_connect(ag);
> - if (ret)
> - goto err;
> -
> - phy_start(ndev->phydev);
> + phylink_start(ag->phylink);
>
> return 0;
>
> @@ -1268,8 +1289,7 @@ static int ag71xx_stop(struct net_device *ndev)
> {
> struct ag71xx *ag = netdev_priv(ndev);
>
> - phy_stop(ndev->phydev);
> - phy_disconnect(ndev->phydev);
> + phylink_stop(ag->phylink);
> ag71xx_hw_disable(ag);
>
> return 0;
> @@ -1396,10 +1416,9 @@ static netdev_tx_t ag71xx_hard_start_xmit(struct sk_buff *skb,
>
> static int ag71xx_do_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd)
> {
> - if (!ndev->phydev)
> - return -EINVAL;
> + struct ag71xx *ag = netdev_priv(ndev);
>
> - return phy_mii_ioctl(ndev->phydev, ifr, cmd);
> + return phylink_mii_ioctl(ag->phylink, ifr, cmd);
> }
>
> static void ag71xx_oom_timer_handler(struct timer_list *t)
> @@ -1422,13 +1441,14 @@ static void ag71xx_restart_work_func(struct work_struct *work)
> {
> struct ag71xx *ag = container_of(work, struct ag71xx,
> restart_work.work);
> - struct net_device *ndev = ag->ndev;
>
> rtnl_lock();
> ag71xx_hw_disable(ag);
> ag71xx_hw_enable(ag);
> - if (ndev->phydev->link)
> - ag71xx_link_adjust(ag, false);
> +
> + phylink_stop(ag->phylink);
> + phylink_start(ag->phylink);
> +
> rtnl_unlock();
> }
>
> @@ -1769,6 +1789,12 @@ static int ag71xx_probe(struct platform_device *pdev)
>
> platform_set_drvdata(pdev, ndev);
>
> + err = ag71xx_phy_setup(ag);
> + if (err) {
> + netif_err(ag, probe, ndev, "failed to setup phy (%d)\n", err);
> + goto err_mdio_remove;
> + }
> +
> err = register_netdev(ndev);
> if (err) {
> netif_err(ag, probe, ndev, "unable to register net device\n");
> --
> 2.23.0
>
>
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
next prev parent reply other threads:[~2019-10-18 9:54 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-18 9:39 [PATCH v2 0/5] add dsa switch support for ar9331 Oleksij Rempel
2019-10-18 9:39 ` [PATCH v2 1/5] net: ag71xx: port to phylink Oleksij Rempel
2019-10-18 9:53 ` Russell King - ARM Linux admin [this message]
2019-10-18 9:39 ` [PATCH v2 2/5] dt-bindings: net: dsa: qca,ar9331 switch documentation Oleksij Rempel
2019-10-18 9:39 ` [PATCH v2 3/5] MIPS: ath79: ar9331: add ar9331-switch node Oleksij Rempel
2019-10-18 9:39 ` [PATCH v2 4/5] net: dsa: add support for Atheros AR9331 TAG format Oleksij Rempel
2019-10-18 9:39 ` [PATCH v2 5/5] net: dsa: add support for Atheros AR9331 build-in switch Oleksij Rempel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191018095349.GF25745@shell.armlinux.org.uk \
--to=linux@armlinux.org.uk \
--cc=andrew@lunn.ch \
--cc=chris.snook@gmail.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=jcliburn@gmail.com \
--cc=jhogan@kernel.org \
--cc=kernel@pengutronix.de \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=netdev@vger.kernel.org \
--cc=o.rempel@pengutronix.de \
--cc=paul.burton@mips.com \
--cc=ralf@linux-mips.org \
--cc=robh+dt@kernel.org \
--cc=vivien.didelot@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.