* [PATCH iproute2 0/3] remove old examples
@ 2019-10-23 16:16 Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 1/3] examples: remove out of date cbq stuff Stephen Hemminger
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Stephen Hemminger @ 2019-10-23 16:16 UTC (permalink / raw)
To: netdev; +Cc: Stephen Hemminger
Take the old stuff away.
Stephen Hemminger (3):
examples: remove out of date cbq stuff
examples: remove gaiconf
examples: remove diffserv
examples/README.cbq | 122 -----------------
examples/SYN-DoS.rate.limit | 49 -------
examples/cbqinit.eth1 | 76 ----------
examples/diffserv/Edge1 | 68 ---------
examples/diffserv/Edge2 | 87 ------------
examples/diffserv/Edge31-ca-u32 | 170 -----------------------
examples/diffserv/Edge31-cb-chains | 132 ------------------
examples/diffserv/Edge32-ca-u32 | 198 ---------------------------
examples/diffserv/Edge32-cb-chains | 144 -------------------
examples/diffserv/Edge32-cb-u32 | 145 --------------------
examples/diffserv/README | 98 -------------
examples/diffserv/afcbq | 105 --------------
examples/diffserv/ef-prio | 25 ----
examples/diffserv/efcbq | 31 -----
examples/diffserv/regression-testing | 125 -----------------
examples/gaiconf | 134 ------------------
16 files changed, 1709 deletions(-)
delete mode 100644 examples/README.cbq
delete mode 100644 examples/SYN-DoS.rate.limit
delete mode 100644 examples/cbqinit.eth1
delete mode 100644 examples/diffserv/Edge1
delete mode 100644 examples/diffserv/Edge2
delete mode 100644 examples/diffserv/Edge31-ca-u32
delete mode 100644 examples/diffserv/Edge31-cb-chains
delete mode 100644 examples/diffserv/Edge32-ca-u32
delete mode 100644 examples/diffserv/Edge32-cb-chains
delete mode 100644 examples/diffserv/Edge32-cb-u32
delete mode 100644 examples/diffserv/README
delete mode 100644 examples/diffserv/afcbq
delete mode 100644 examples/diffserv/ef-prio
delete mode 100644 examples/diffserv/efcbq
delete mode 100644 examples/diffserv/regression-testing
delete mode 100644 examples/gaiconf
--
2.20.1
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH iproute2 1/3] examples: remove out of date cbq stuff
2019-10-23 16:16 [PATCH iproute2 0/3] remove old examples Stephen Hemminger
@ 2019-10-23 16:16 ` Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 2/3] examples: remove gaiconf Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 3/3] examples: remove diffserv Stephen Hemminger
2 siblings, 0 replies; 4+ messages in thread
From: Stephen Hemminger @ 2019-10-23 16:16 UTC (permalink / raw)
To: netdev; +Cc: Stephen Hemminger
The examples around cbq are out of date and never updated.
There are better ways to achieve same kind of thing with more
modern qdisc.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
---
examples/README.cbq | 122 ------------------------------------
examples/SYN-DoS.rate.limit | 49 ---------------
examples/cbqinit.eth1 | 76 ----------------------
3 files changed, 247 deletions(-)
delete mode 100644 examples/README.cbq
delete mode 100644 examples/SYN-DoS.rate.limit
delete mode 100644 examples/cbqinit.eth1
diff --git a/examples/README.cbq b/examples/README.cbq
deleted file mode 100644
index 38c1089d1d1e..000000000000
--- a/examples/README.cbq
+++ /dev/null
@@ -1,122 +0,0 @@
-# CHANGES
-# -------
-# v0.3a2- fixed bug in "if" operator. Thanks kad@dgtu.donetsk.ua.
-# v0.3a- added TIME parameter. Example:
-# TIME=00:00-19:00;64Kbit/6Kbit
-# So, between 00:00 and 19:00 RATE will be 64Kbit.
-# Just start "cbq.init timecheck" periodically from cron (every 10
-# minutes for example).
-# !!! Anyway you MUST start "cbq.init start" for CBQ initialize.
-# v0.2 - Some cosmetique changes. Now it more compatible with
-# old bash version. Thanks to Stanislav V. Voronyi
-# <stas@cnti.uanet.kharkov.ua>.
-# v0.1 - First public release
-#
-# README
-# ------
-#
-# First of all - this is just a SIMPLE EXAMPLE of CBQ power.
-# Don't ask me "why" and "how" :)
-#
-# This is an example of using CBQ (Class Based Queueing) and policy-based
-# filter for building smart ethernet shapers. All CBQ parameters are
-# correct only for ETHERNET (eth0,1,2..) linux interfaces. It works for
-# ARCNET too (just set bandwidth parameter to 2Mbit). It was tested
-# on 2.1.125-2.1.129 linux kernels (KSI linux, Nostromo version) and
-# ip-route utility by A.Kuznetsov (iproute2-ss981101 version).
-# You can download ip-route from ftp://ftp.inr.ac.ru/ip-routing or
-# get iproute2*.rpm (compiled with glibc) from ftp.ksi-linux.com.
-#
-#
-# HOW IT WORKS
-#
-# Each shaper must be described by config file in $CBQ_PATH
-# (/etc/sysconfig/cbq/) directory - one config file for each CBQ shaper.
-#
-# Some words about config file name:
-# Each shaper has its personal ID - two byte HEX number. Really ID is
-# CBQ class.
-# So, filename looks like:
-#
-# cbq-1280.My_first_shaper
-# ^^^ ^^^ ^^^^^^^^^^^^^
-# | | |______ Shaper name - any word
-# | |___________________ ID (0000-FFFF), let ID looks like shaper's rate
-# |______________________ Filename must begin from "cbq-"
-#
-#
-# Config file describes shaper parameters and source[destination]
-# address[port].
-# For example let's prepare /etc/sysconfig/cbq/cbq-1280.My_first_shaper:
-#
-# ----------8<---------------------
-# DEVICE=eth0,10Mbit,1Mbit
-# RATE=128Kbit
-# WEIGHT=10Kbit
-# PRIO=5
-# RULE=192.168.1.0/24
-# ----------8<---------------------
-#
-# This is minimal configuration, where:
-# DEVICE: eth0 - device where we do control our traffic
-# 10Mbit - REAL ethernet card bandwidth
-# 1Mbit - "weight" of :1 class (parent for all shapers for eth0),
-# as a rule of thumb weight=batdwidth/10.
-# 100Mbit adapter's example: DEVICE=eth0,100Mbit,10Mbit
-# *** If you want to build more than one shaper per device it's
-# enough to describe bandwidth and weight once - cbq.init
-# is smart :) You can put only 'DEVICE=eth0' into cbq-*
-# config file for eth0.
-#
-# RATE: Shaper's speed - Kbit,Mbit or bps (bytes per second)
-#
-# WEIGHT: "weight" of shaper (CBQ class). Like for DEVICE - approx. RATE/10
-#
-# PRIO: shaper's priority from 1 to 8 where 1 is the highest one.
-# I do always use "5" for all my shapers.
-#
-# RULE: [source addr][:source port],[dest addr][:dest port]
-# Some examples:
-# RULE=10.1.1.0/24:80 - all traffic for network 10.1.1.0 to port 80
-# will be shaped.
-# RULE=10.2.2.5 - shaper works only for IP address 10.2.2.5
-# RULE=:25,10.2.2.128/25:5000 - all traffic from any address and port 25 to
-# address 10.2.2.128 - 10.2.2.255 and port 5000
-# will be shaped.
-# RULE=10.5.5.5:80, - shaper active only for traffic from port 80 of
-# address 10.5.5.5
-# Multiple RULE fields per one config file are allowed. For example:
-# RULE=10.1.1.2:80
-# RULE=10.1.1.2:25
-# RULE=10.1.1.2:110
-#
-# *** ATTENTION!!!
-# All shapers do work only for outgoing traffic!
-# So, if you want to build bidirectional shaper you must set it up for
-# both ethernet card. For example let's build shaper for our linux box like:
-#
-# --------- 192.168.1.1
-# BACKBONE -----eth0-| linux |-eth1------*[our client]
-# ---------
-#
-# Let all traffic from backbone to client will be shaped at 28Kbit and
-# traffic from client to backbone - at 128Kbit. We need two config files:
-#
-# ---8<-----/etc/sysconfig/cbq/cbq-28.client-out----
-# DEVICE=eth1,10Mbit,1Mbit
-# RATE=28Kbit
-# WEIGHT=2Kbit
-# PRIO=5
-# RULE=192.168.1.1
-# ---8<---------------------------------------------
-#
-# ---8<-----/etc/sysconfig/cbq/cbq-128.client-in----
-# DEVICE=eth0,10Mbit,1Mbit
-# RATE=128Kbit
-# WEIGHT=10Kbit
-# PRIO=5
-# RULE=192.168.1.1,
-# ---8<---------------------------------------------
-# ^pay attention to "," - this is source address!
-#
-# Enjoy.
diff --git a/examples/SYN-DoS.rate.limit b/examples/SYN-DoS.rate.limit
deleted file mode 100644
index 8766b679ce36..000000000000
--- a/examples/SYN-DoS.rate.limit
+++ /dev/null
@@ -1,49 +0,0 @@
-#! /bin/sh -x
-#
-# sample script on using the ingress capabilities
-# this script shows how one can rate limit incoming SYNs
-# Useful for TCP-SYN attack protection. You can use
-# IPchains to have more powerful additions to the SYN (eg
-# in addition the subnet)
-#
-#path to various utilities;
-#change to reflect yours.
-#
-IPROUTE=/root/DS-6-beta/iproute2-990530-dsing
-TC=$IPROUTE/tc/tc
-IP=$IPROUTE/ip/ip
-IPCHAINS=/root/DS-6-beta/ipchains-1.3.9/ipchains
-INDEV=eth2
-#
-# tag all incoming SYN packets through $INDEV as mark value 1
-############################################################
-$IPCHAINS -A input -i $INDEV -y -m 1
-############################################################
-#
-# install the ingress qdisc on the ingress interface
-############################################################
-$TC qdisc add dev $INDEV handle ffff: ingress
-############################################################
-
-#
-#
-# SYN packets are 40 bytes (320 bits) so three SYNs equals
-# 960 bits (approximately 1kbit); so we rate limit below
-# the incoming SYNs to 3/sec (not very sueful really; but
-#serves to show the point - JHS
-############################################################
-$TC filter add dev $INDEV parent ffff: protocol ip prio 50 handle 1 fw \
-police rate 1kbit burst 40 mtu 9k drop flowid :1
-############################################################
-
-
-#
-echo "---- qdisc parameters Ingress ----------"
-$TC qdisc ls dev $INDEV
-echo "---- Class parameters Ingress ----------"
-$TC class ls dev $INDEV
-echo "---- filter parameters Ingress ----------"
-$TC filter ls dev $INDEV parent ffff:
-
-#deleting the ingress qdisc
-#$TC qdisc del $INDEV ingress
diff --git a/examples/cbqinit.eth1 b/examples/cbqinit.eth1
deleted file mode 100644
index 226ec1c54072..000000000000
--- a/examples/cbqinit.eth1
+++ /dev/null
@@ -1,76 +0,0 @@
-#! /bin/sh
-
-TC=/home/root/tc
-IP=/home/root/ip
-DEVICE=eth1
-BANDWIDTH="bandwidth 10Mbit"
-
-# Attach CBQ on $DEVICE. It will have handle 1:.
-# $BANDWIDTH is real $DEVICE bandwidth (10Mbit).
-# avpkt is average packet size.
-# mpu is minimal packet size.
-
-$TC qdisc add dev $DEVICE root handle 1: cbq \
-$BANDWIDTH avpkt 1000 mpu 64
-
-# Create root class with classid 1:1. This step is not necessary.
-# bandwidth is the same as on CBQ itself.
-# rate == all the bandwidth
-# allot is MTU + MAC header
-# maxburst measure allowed class burstiness (please,read S.Floyd and VJ papers)
-# est 1sec 8sec means, that kernel will evaluate average rate
-# on this class with period 1sec and time constant 8sec.
-# This rate is viewed with "tc -s class ls dev $DEVICE"
-
-$TC class add dev $DEVICE parent 1:0 classid :1 est 1sec 8sec cbq \
-$BANDWIDTH rate 10Mbit allot 1514 maxburst 50 avpkt 1000
-
-# Bulk.
-# New parameters are:
-# weight, which is set to be proportional to
-# "rate". It is not necessary, weight=1 will work as well.
-# defmap and split say that best effort ttraffic, not classfied
-# by another means will fall to this class.
-
-$TC class add dev $DEVICE parent 1:1 classid :2 est 1sec 8sec cbq \
-$BANDWIDTH rate 4Mbit allot 1514 weight 500Kbit \
-prio 6 maxburst 50 avpkt 1000 split 1:0 defmap ff3d
-
-# OPTIONAL.
-# Attach "sfq" qdisc to this class, quantum is MTU, perturb
-# gives period of hash function perturbation in seconds.
-#
-$TC qdisc add dev $DEVICE parent 1:2 sfq quantum 1514b perturb 15
-
-# Interactive-burst class
-
-$TC class add dev $DEVICE parent 1:1 classid :3 est 2sec 16sec cbq \
-$BANDWIDTH rate 1Mbit allot 1514 weight 100Kbit \
-prio 2 maxburst 100 avpkt 1000 split 1:0 defmap c0
-
-$TC qdisc add dev $DEVICE parent 1:3 sfq quantum 1514b perturb 15
-
-# Background.
-
-$TC class add dev $DEVICE parent 1:1 classid :4 est 1sec 8sec cbq \
- $BANDWIDTH rate 100Kbit allot 1514 weight 10Mbit \
- prio 7 maxburst 10 avpkt 1000 split 1:0 defmap 2
-
-$TC qdisc add dev $DEVICE parent 1:4 sfq quantum 1514b perturb 15
-
-# Realtime class for RSVP
-
-$TC class add dev $DEVICE parent 1:1 classid 1:7FFE cbq \
-rate 5Mbit $BANDWIDTH allot 1514b avpkt 1000 \
-maxburst 20
-
-# Reclassified realtime traffic
-#
-# New element: split is not 1:0, but 1:7FFE. It means,
-# that only real-time packets, which violated policing filters
-# or exceeded reshaping buffers will fall to it.
-
-$TC class add dev $DEVICE parent 1:7FFE classid 1:7FFF est 4sec 32sec cbq \
-rate 1Mbit $BANDWIDTH allot 1514b avpkt 1000 weight 10Kbit \
-prio 6 maxburst 10 split 1:7FFE defmap ffff
-
--
2.20.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH iproute2 2/3] examples: remove gaiconf
2019-10-23 16:16 [PATCH iproute2 0/3] remove old examples Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 1/3] examples: remove out of date cbq stuff Stephen Hemminger
@ 2019-10-23 16:16 ` Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 3/3] examples: remove diffserv Stephen Hemminger
2 siblings, 0 replies; 4+ messages in thread
From: Stephen Hemminger @ 2019-10-23 16:16 UTC (permalink / raw)
To: netdev; +Cc: Stephen Hemminger
The gaiconf script is a workaround for something now handled
in distros as part of libc.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
---
examples/gaiconf | 134 -----------------------------------------------
1 file changed, 134 deletions(-)
delete mode 100644 examples/gaiconf
diff --git a/examples/gaiconf b/examples/gaiconf
deleted file mode 100644
index d75292b900cc..000000000000
--- a/examples/gaiconf
+++ /dev/null
@@ -1,134 +0,0 @@
-#!/bin/sh
-
-#
-# Setup address label from /etc/gai.conf
-#
-# Written by YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>, 2010.
-#
-
-IP=ip
-DEFAULT_GAICONF=/etc/gai.conf
-verbose=
-debug=
-
-function run ()
-{
- if [ x"$verbose" != x"" ]; then
- echo "$@"
- fi
- if [ x"$debug" = x"" ]; then
- "$@"
- fi
-}
-
-function do_load_config ()
-{
- file=$1; shift
- flush=1
- cat $file | while read command prefix label; do
- if [ x"$command" = x"#label" ]; then
- if [ ${flush} = 1 ]; then
- run ${IP} -6 addrlabel flush
- flush=0
- fi
- run ${IP} -6 addrlabel add prefix $prefix label $label
- fi
- done
-}
-
-function do_list_config ()
-{
- ${IP} -6 addrlabel list | while read p pfx l lbl; do
- echo label ${pfx} ${lbl}
- done
-}
-
-function help ()
-{
- echo "Usage: $0 [-v] {--list | --config [ ${DEFAULT_GAICONF} ] | --default}"
- exit 1
-}
-
-TEMP=`getopt -o c::dlv -l config::,default,list,verbose -n gaiconf -- "$@"`
-
-if [ $? != 0 ]; then
- echo "Terminating..." >&2
- exit 1
-fi
-
-TEMPFILE=`mktemp`
-
-eval set -- "$TEMP"
-
-while true ; do
- case "$1" in
- -c|--config)
- if [ x"$cmd" != x"" ]; then
- help
- fi
- case "$2" in
- "") gai_conf="${DEFAULT_GAICONF}"
- shift 2
- ;;
- *) gai_conf="$2"
- shift 2
- esac
- cmd=config
- ;;
- -d|--default)
- if [ x"$cmd" != x"" ]; then
- help
- fi
- gai_conf=${TEMPFILE}
- cmd=config
- ;;
- -l|--list)
- if [ x"$cmd" != x"" ]; then
- help
- fi
- cmd=list
- shift
- ;;
- -v)
- verbose=1
- shift
- ;;
- --)
- shift;
- break
- ;;
- *)
- echo "Internal error!" >&2
- exit 1
- ;;
- esac
-done
-
-case "$cmd" in
- config)
- if [ x"$gai_conf" = x"${TEMPFILE}" ]; then
- sed -e 's/^[[:space:]]*//' <<END_OF_DEFAULT >${TEMPFILE}
- label ::1/128 0
- label ::/0 1
- label 2002::/16 2
- label ::/96 3
- label ::ffff:0:0/96 4
- label fec0::/10 5
- label fc00::/7 6
- label 2001:0::/32 7
-END_OF_DEFAULT
- fi
- do_load_config "$gai_conf"
- ;;
- list)
- do_list_config
- ;;
- *)
- help
- ;;
-esac
-
-rm -f "${TEMPFILE}"
-
-exit 0
-
--
2.20.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH iproute2 3/3] examples: remove diffserv
2019-10-23 16:16 [PATCH iproute2 0/3] remove old examples Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 1/3] examples: remove out of date cbq stuff Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 2/3] examples: remove gaiconf Stephen Hemminger
@ 2019-10-23 16:16 ` Stephen Hemminger
2 siblings, 0 replies; 4+ messages in thread
From: Stephen Hemminger @ 2019-10-23 16:16 UTC (permalink / raw)
To: netdev; +Cc: Stephen Hemminger
The diffserv examples here are out of date and incomplete.
Remove them rather than try and fix them.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
---
examples/diffserv/Edge1 | 68 ---------
examples/diffserv/Edge2 | 87 ------------
examples/diffserv/Edge31-ca-u32 | 170 -----------------------
examples/diffserv/Edge31-cb-chains | 132 ------------------
examples/diffserv/Edge32-ca-u32 | 198 ---------------------------
examples/diffserv/Edge32-cb-chains | 144 -------------------
examples/diffserv/Edge32-cb-u32 | 145 --------------------
examples/diffserv/README | 98 -------------
examples/diffserv/afcbq | 105 --------------
examples/diffserv/ef-prio | 25 ----
examples/diffserv/efcbq | 31 -----
examples/diffserv/regression-testing | 125 -----------------
12 files changed, 1328 deletions(-)
delete mode 100644 examples/diffserv/Edge1
delete mode 100644 examples/diffserv/Edge2
delete mode 100644 examples/diffserv/Edge31-ca-u32
delete mode 100644 examples/diffserv/Edge31-cb-chains
delete mode 100644 examples/diffserv/Edge32-ca-u32
delete mode 100644 examples/diffserv/Edge32-cb-chains
delete mode 100644 examples/diffserv/Edge32-cb-u32
delete mode 100644 examples/diffserv/README
delete mode 100644 examples/diffserv/afcbq
delete mode 100644 examples/diffserv/ef-prio
delete mode 100644 examples/diffserv/efcbq
delete mode 100644 examples/diffserv/regression-testing
diff --git a/examples/diffserv/Edge1 b/examples/diffserv/Edge1
deleted file mode 100644
index 4ddffdd195f1..000000000000
--- a/examples/diffserv/Edge1
+++ /dev/null
@@ -1,68 +0,0 @@
-#! /bin/sh -x
-#
-# sample script on using the ingress capabilities
-# This script just tags on the ingress interfac using Ipchains
-# the result is used for fast classification and re-marking
-# on the egress interface
-#
-#path to various utilities;
-#change to reflect yours.
-#
-IPROUTE=/root/DS-6-beta/iproute2-990530-dsing
-TC=$IPROUTE/tc/tc
-IP=$IPROUTE/ip/ip
-IPCHAINS=/root/DS-6-beta/ipchains-1.3.9/ipchains
-INDEV=eth2
-EGDEV="dev eth1"
-#
-# tag all incoming packets from host 10.2.0.24 to value 1
-# tag all incoming packets from host 10.2.0.3 to value 2
-# tag the rest of incoming packets from subnet 10.2.0.0/24 to value 3
-#These values are used in the egress
-#
-############################################################
-$IPCHAINS -A input -s 10.2.0.4/24 -m 3
-$IPCHAINS -A input -i $INDEV -s 10.2.0.24 -m 1
-$IPCHAINS -A input -i $INDEV -s 10.2.0.3 -m 2
-
-######################## Egress side ########################
-
-
-# attach a dsmarker
-#
-$TC qdisc add $EGDEV handle 1:0 root dsmark indices 64 set_tc_index
-#
-# values of the DSCP to change depending on the class
-#
-#becomes EF
-$TC class change $EGDEV classid 1:1 dsmark mask 0x3 \
- value 0xb8
-#becomes AF11
-$TC class change $EGDEV classid 1:2 dsmark mask 0x3 \
- value 0x28
-#becomes AF21
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x48
-#
-#
-# The class mapping
-#
-$TC filter add $EGDEV parent 1:0 protocol ip prio 4 handle 1 fw classid 1:1
-$TC filter add $EGDEV parent 1:0 protocol ip prio 4 handle 2 fw classid 1:2
-$TC filter add $EGDEV parent 1:0 protocol ip prio 4 handle 3 fw classid 1:3
-#
-
-#
-echo "---- qdisc parameters Ingress ----------"
-$TC qdisc ls dev $INDEV
-echo "---- Class parameters Ingress ----------"
-$TC class ls dev $INDEV
-echo "---- filter parameters Ingress ----------"
-$TC filter ls dev $INDEV parent 1:0
-
-echo "---- qdisc parameters Egress ----------"
-$TC qdisc ls $EGDEV
-echo "---- Class parameters Egress ----------"
-$TC class ls $EGDEV
-echo "---- filter parameters Egress ----------"
-$TC filter ls $EGDEV parent 1:0
diff --git a/examples/diffserv/Edge2 b/examples/diffserv/Edge2
deleted file mode 100644
index f81f510fc06f..000000000000
--- a/examples/diffserv/Edge2
+++ /dev/null
@@ -1,87 +0,0 @@
-#! /bin/sh -x
-#
-# sample script on using the ingress capabilities
-# This script tags the fwmark on the ingress interface using IPchains
-# the result is used first for policing on the Ingress interface then
-# for fast classification and re-marking
-# on the egress interface
-#
-#path to various utilities;
-#change to reflect yours.
-#
-IPROUTE=/root/DS-6-beta/iproute2-990530-dsing
-TC=$IPROUTE/tc/tc
-IP=$IPROUTE/ip/ip
-IPCHAINS=/root/DS-6-beta/ipchains-1.3.9/ipchains
-INDEV=eth2
-EGDEV="dev eth1"
-#
-# tag all incoming packets from host 10.2.0.24 to value 1
-# tag all incoming packets from host 10.2.0.3 to value 2
-# tag the rest of incoming packets from subnet 10.2.0.0/24 to value 3
-#These values are used in the egress
-############################################################
-$IPCHAINS -A input -s 10.2.0.0/24 -m 3
-$IPCHAINS -A input -i $INDEV -s 10.2.0.24 -m 1
-$IPCHAINS -A input -i $INDEV -s 10.2.0.3 -m 2
-############################################################
-#
-# install the ingress qdisc on the ingress interface
-############################################################
-$TC qdisc add dev $INDEV handle ffff: ingress
-############################################################
-
-#
-# attach a fw classifier to the ingress which polices anything marked
-# by ipchains to tag value 3 (The rest of the subnet packets -- not
-# tag 1 or 2) to not go beyond 1.5Mbps
-# Allow up to at least 60 packets to burst (assuming maximum packet
-# size of # 1.5 KB) in the long run and up to about 6 packets in the
-# shot run
-
-############################################################
-$TC filter add dev $INDEV parent ffff: protocol ip prio 50 handle 3 fw \
-police rate 1500kbit burst 90k mtu 9k drop flowid :1
-############################################################
-
-######################## Egress side ########################
-
-
-# attach a dsmarker
-#
-$TC qdisc add $EGDEV handle 1:0 root dsmark indices 64
-#
-# values of the DSCP to change depending on the class
-#
-$TC class change $EGDEV classid 1:1 dsmark mask 0x3 \
- value 0xb8
-$TC class change $EGDEV classid 1:2 dsmark mask 0x3 \
- value 0x28
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x48
-#
-#
-# The class mapping
-#
-$TC filter add $EGDEV parent 1:0 protocol ip prio 4 handle 1 fw classid 1:1
-$TC filter add $EGDEV parent 1:0 protocol ip prio 4 handle 2 fw classid 1:2
-$TC filter add $EGDEV parent 1:0 protocol ip prio 4 handle 3 fw classid 1:3
-#
-
-#
-echo "---- qdisc parameters Ingress ----------"
-$TC qdisc ls dev $INDEV
-echo "---- Class parameters Ingress ----------"
-$TC class ls dev $INDEV
-echo "---- filter parameters Ingress ----------"
-$TC filter ls dev $INDEV parent ffff:
-
-echo "---- qdisc parameters Egress ----------"
-$TC qdisc ls $EGDEV
-echo "---- Class parameters Egress ----------"
-$TC class ls $EGDEV
-echo "---- filter parameters Egress ----------"
-$TC filter ls $EGDEV parent 1:0
-#
-#deleting the ingress qdisc
-#$TC qdisc del $DEV ingress
diff --git a/examples/diffserv/Edge31-ca-u32 b/examples/diffserv/Edge31-ca-u32
deleted file mode 100644
index 7344851aec32..000000000000
--- a/examples/diffserv/Edge31-ca-u32
+++ /dev/null
@@ -1,170 +0,0 @@
-#! /bin/sh -x
-#
-# sample script on using the ingress capabilities using u32 classifier
-# This script tags tcindex based on metering on the ingress
-# interface the result is used for fast classification and re-marking
-# on the egress interface
-# This is an example of a color aware mode marker with PIR configured
-# based on draft-wahjak-mcm-00.txt (section 3.1)
-#
-# The colors are defined using the Diffserv Fields
-#path to various utilities;
-#change to reflect yours.
-#
-IPROUTE=/usr/src/iproute2-current
-TC=$IPROUTE/tc/tc
-IP=$IPROUTE/ip/ip
-INDEV=eth0
-EGDEV="dev eth1"
-CIR1=1500kbit
-CIR2=1000kbit
-
-#The CBS is about 60 MTU sized packets
-CBS1=90k
-CBS2=90k
-
-############################################################
-#
-# install the ingress qdisc on the ingress interface
-$TC qdisc add dev $INDEV handle ffff: ingress
-############################################################
-#
-# Create u32 filters
-$TC filter add dev $INDEV parent ffff: protocol ip prio 4 handle 1: u32 \
-divisor 1
-############################################################
-
-# The meters: Note that we have shared meters in this case as identified
-# by the index parameter
-meter1=" police index 1 rate $CIR1 burst $CBS1 "
-meter2=" police index 2 rate $CIR2 burst $CBS1 "
-meter3=" police index 3 rate $CIR2 burst $CBS2 "
-meter4=" police index 4 rate $CIR1 burst $CBS2 "
-meter5=" police index 5 rate $CIR1 burst $CBS2 "
-
-# All packets are marked with a tcindex value which is used on the egress
-# tcindex 1 maps to AF41, 2->AF42, 3->AF43, 4->BE
-
-# *********************** AF41 ***************************
-#AF41 (DSCP 0x22) is passed on with a tcindex value 1
-#if it doesn't exceed its CIR/CBS
-#policer 1 is used.
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 4 u32 \
-match ip tos 0x88 0xfc \
-$meter1 \
-continue flowid :1
-#
-# if it exceeds the above but not the extra rate/burst below, it gets a
-# tcindex value of 2
-# policer 2 is used
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 5 u32 \
-match ip tos 0x88 0xfc \
-$meter2 \
-continue flowid :2
-#
-# if it exceeds the above but not the rule below, it gets a tcindex value
-# of 3 (policer 3)
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 6 u32 \
-match ip tos 0x88 0xfc \
-$meter3 \
-drop flowid :3
-#
-
-# *********************** AF42 ***************************
-#AF42 (DSCP 0x24) from is passed on with a tcindex value 2
-#if it doesn't exceed its CIR/CBS
-#policer 2 is used. Note that this is shared with the AF41
-#
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 5 u32 \
-match ip tos 0x90 0xfc \
-$meter2 \
-continue flowid :2
-#
-# if it exceeds the above but not the rule below, it gets a tcindex value
-# of 3 (policer 3)
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 6 u32 \
-match ip tos 0x90 0xfc \
-$meter3 \
-drop flowid :3
-#
-# *********************** AF43 ***************************
-#
-#AF43 (DSCP 0x26) from is passed on with a tcindex value 3
-#if it doesn't exceed its CIR/CBS
-#policer 3 is used. Note that this is shared with the AF41 and AF42
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 6 u32 \
-match ip tos 0x98 0xfc \
-$meter3 \
-drop flowid :3
-#
-# *********************** BE ***************************
-#
-# Anything else (not from the AF4*) gets discarded if it
-# exceeds 1Mbps and by default goes to BE if it doesn't
-# Note that the BE class is also used by the AF4* in the worst
-# case
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 7 u32 \
-match ip src 0/0\
-$meter4 \
-drop flowid :4
-
-######################## Egress side ########################
-
-# attach a dsmarker
-#
-$TC qdisc add $EGDEV handle 1:0 root dsmark indices 64
-#
-# values of the DSCP to change depending on the class
-#note that the ECN bits are masked out
-#
-#AF41 (0x88 is 0x22 shifted to the right by two bits)
-#
-$TC class change $EGDEV classid 1:1 dsmark mask 0x3 \
- value 0x88
-#AF42
-$TC class change $EGDEV classid 1:2 dsmark mask 0x3 \
- value 0x90
-#AF43
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x98
-#BE
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x0
-#
-#
-# The class mapping
-#
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 1 tcindex classid 1:1
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 2 tcindex classid 1:2
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 3 tcindex classid 1:3
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 4 tcindex classid 1:4
-#
-
-#
-echo "---- qdisc parameters Ingress ----------"
-$TC qdisc ls dev $INDEV
-echo "---- Class parameters Ingress ----------"
-$TC class ls dev $INDEV
-echo "---- filter parameters Ingress ----------"
-$TC filter ls dev $INDEV parent ffff:
-
-echo "---- qdisc parameters Egress ----------"
-$TC qdisc ls $EGDEV
-echo "---- Class parameters Egress ----------"
-$TC class ls $EGDEV
-echo "---- filter parameters Egress ----------"
-$TC filter ls $EGDEV parent 1:0
-#
-#deleting the ingress qdisc
-#$TC qdisc del $INDEV ingress
diff --git a/examples/diffserv/Edge31-cb-chains b/examples/diffserv/Edge31-cb-chains
deleted file mode 100644
index 49c396bc9af7..000000000000
--- a/examples/diffserv/Edge31-cb-chains
+++ /dev/null
@@ -1,132 +0,0 @@
-#! /bin/sh -x
-#
-# sample script on using the ingress capabilities
-# This script fwmark tags(IPchains) based on metering on the ingress
-# interface the result is used for fast classification and re-marking
-# on the egress interface
-# This is an example of a color blind mode marker with no PIR configured
-# based on draft-wahjak-mcm-00.txt (section 3.1)
-#
-#path to various utilities;
-#change to reflect yours.
-#
-IPROUTE=/root/DS-6-beta/iproute2-990530-dsing
-TC=$IPROUTE/tc/tc
-IP=$IPROUTE/ip/ip
-IPCHAINS=/root/DS-6-beta/ipchains-1.3.9/ipchains
-INDEV=eth2
-EGDEV="dev eth1"
-CIR1=1500kbit
-CIR2=1000kbit
-
-#The CBS is about 60 MTU sized packets
-CBS1=90k
-CBS2=90k
-
-meter1="police rate $CIR1 burst $CBS1 "
-meter2="police rate $CIR1 burst $CBS2 "
-meter3="police rate $CIR2 burst $CBS1 "
-meter4="police rate $CIR2 burst $CBS2 "
-meter5="police rate $CIR2 burst $CBS2 "
-#
-# tag the rest of incoming packets from subnet 10.2.0.0/24 to fw value 1
-# tag all incoming packets from any other subnet to fw tag 2
-############################################################
-$IPCHAINS -A input -i $INDEV -s 0/0 -m 2
-$IPCHAINS -A input -i $INDEV -s 10.2.0.0/24 -m 1
-#
-############################################################
-# install the ingress qdisc on the ingress interface
-$TC qdisc add dev $INDEV handle ffff: ingress
-#
-############################################################
-
-# All packets are marked with a tcindex value which is used on the egress
-# tcindex 1 maps to AF41, 2->AF42, 3->AF43, 4->BE
-#
-############################################################
-#
-# anything with fw tag of 1 is passed on with a tcindex value 1
-#if it doesn't exceed its allocated rate (CIR/CBS)
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 4 handle 1 fw \
-$meter1 \
-continue flowid 4:1
-#
-# if it exceeds the above but not the extra rate/burst below, it gets a
-#tcindex value of 2
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 5 handle 1 fw \
-$meter2 \
-continue flowid 4:2
-#
-# if it exceeds the above but not the rule below, it gets a tcindex value
-# of 3
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 6 handle 1 fw \
-$meter3 \
-drop flowid 4:3
-#
-# Anything else (not from the subnet 10.2.0.24/24) gets discarded if it
-# exceeds 1Mbps and by default goes to BE if it doesn't
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 6 handle 2 fw \
-$meter5 \
-drop flowid 4:4
-
-
-######################## Egress side ########################
-
-
-# attach a dsmarker
-#
-$TC qdisc add $EGDEV handle 1:0 root dsmark indices 64
-#
-# values of the DSCP to change depending on the class
-#note that the ECN bits are masked out
-#
-#AF41 (0x88 is 0x22 shifted to the right by two bits)
-#
-$TC class change $EGDEV classid 1:1 dsmark mask 0x3 \
- value 0x88
-#AF42
-$TC class change $EGDEV classid 1:2 dsmark mask 0x3 \
- value 0x90
-#AF43
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x98
-#BE
-$TC class change $EGDEV classid 1:4 dsmark mask 0x3 \
- value 0x0
-#
-#
-# The class mapping (using tcindex; could easily have
-# replaced it with the fw classifier instead)
-#
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 1 tcindex classid 1:1
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 2 tcindex classid 1:2
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 3 tcindex classid 1:3
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 4 tcindex classid 1:4
-#
-
-#
-echo "---- qdisc parameters Ingress ----------"
-$TC qdisc ls dev $INDEV
-echo "---- Class parameters Ingress ----------"
-$TC class ls dev $INDEV
-echo "---- filter parameters Ingress ----------"
-$TC filter ls dev $INDEV parent ffff:
-
-echo "---- qdisc parameters Egress ----------"
-$TC qdisc ls $EGDEV
-echo "---- Class parameters Egress ----------"
-$TC class ls $EGDEV
-echo "---- filter parameters Egress ----------"
-$TC filter ls $EGDEV parent 1:0
-#
-#deleting the ingress qdisc
-#$TC qdisc del $INDEV ingress
diff --git a/examples/diffserv/Edge32-ca-u32 b/examples/diffserv/Edge32-ca-u32
deleted file mode 100644
index 9d3ccd07796c..000000000000
--- a/examples/diffserv/Edge32-ca-u32
+++ /dev/null
@@ -1,198 +0,0 @@
-#! /bin/sh -x
-#
-# sample script on using the ingress capabilities using u32 classifier
-# This script tags tcindex based on metering on the ingress
-# interface the result is used for fast classification and re-marking
-# on the egress interface
-# This is an example of a color aware mode marker with PIR configured
-# based on draft-wahjak-mcm-00.txt (section 3.2)
-#
-# The colors are defined using the Diffserv Fields
-#path to various utilities;
-#change to reflect yours.
-#
-IPROUTE=/root/DS-6-beta/iproute2-990530-dsing
-TC=$IPROUTE/tc/tc
-IP=$IPROUTE/ip/ip
-IPCHAINS=/root/DS-6-beta/ipchains-1.3.9/ipchains
-INDEV=eth2
-EGDEV="dev eth1"
-CIR1=1000kbit
-CIR2=500kbit
-# the PIR is what is in excess of the CIR
-PIR1=1000kbit
-PIR2=500kbit
-
-#The CBS is about 60 MTU sized packets
-CBS1=90k
-CBS2=90k
-#the EBS is about 20 max sized packets
-EBS1=30k
-EBS2=30k
-
-# The meters: Note that we have shared meters in this case as identified
-# by the index parameter
-meter1=" police index 1 rate $CIR1 burst $CBS1 "
-meter1a=" police index 2 rate $PIR1 burst $EBS1 "
-meter2=" police index 3 rate $CIR2 burst $CBS1 "
-meter2a=" police index 4 rate $PIR2 burst $EBS1 "
-meter3=" police index 5 rate $CIR2 burst $CBS2 "
-meter3a=" police index 6 rate $PIR2 burst $EBS2 "
-meter4=" police index 7 rate $CIR1 burst $CBS2 "
-
-############################################################
-#
-# install the ingress qdisc on the ingress interface
-$TC qdisc add dev $INDEV handle ffff: ingress
-############################################################
-#
-# All packets are marked with a tcindex value which is used on the egress
-# tcindex 1 maps to AF41, 2->AF42, 3->AF43, 4->BE
-#
-# *********************** AF41 ***************************
-#AF41 (DSCP 0x22) from is passed on with a tcindex value 1
-#if it doesn't exceed its CIR/CBS + PIR/EBS
-#policer 1 is used.
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 1 u32 \
-match ip tos 0x88 0xfc \
-$meter1 \
-continue flowid :1
-$TC filter add dev $INDEV parent ffff: protocol ip prio 2 u32 \
-match ip tos 0x88 0xfc \
-$meter1a \
-continue flowid :1
-#
-# if it exceeds the above but not the extra rate/burst below, it gets a
-# tcindex value of 2
-# policer 2 is used
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 3 u32 \
-match ip tos 0x88 0xfc \
-$meter2 \
-continue flowid :2
-$TC filter add dev $INDEV parent ffff: protocol ip prio 4 u32 \
-match ip tos 0x88 0xfc \
-$meter2a \
-continue flowid :2
-#
-# if it exceeds the above but not the rule below, it gets a tcindex value
-# of 3 (policer 3)
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 5 u32 \
-match ip tos 0x88 0xfc \
-$meter3 \
-continue flowid :3
-$TC filter add dev $INDEV parent ffff: protocol ip prio 6 u32 \
-match ip tos 0x88 0xfc \
-$meter3a \
-drop flowid :3
-#
-# *********************** AF42 ***************************
-#AF42 (DSCP 0x24) from is passed on with a tcindex value 2
-#if it doesn't exceed its CIR/CBS + PIR/EBS
-#policer 2 is used. Note that this is shared with the AF41
-#
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 8 u32 \
-match ip tos 0x90 0xfc \
-$meter2 \
-continue flowid :2
-$TC filter add dev $INDEV parent ffff: protocol ip prio 9 u32 \
-match ip tos 0x90 0xfc \
-$meter2a \
-continue flowid :2
-#
-# if it exceeds the above but not the rule below, it gets a tcindex value
-# of 3 (policer 3)
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 10 u32 \
-match ip tos 0x90 0xfc \
-$meter3 \
-continue flowid :3
-$TC filter add dev $INDEV parent ffff: protocol ip prio 11 u32 \
-match ip tos 0x90 0xfc \
-$meter3a \
-drop flowid :3
-
-#
-# *********************** AF43 ***************************
-#
-#AF43 (DSCP 0x26) from is passed on with a tcindex value 3
-#if it doesn't exceed its CIR/CBS + PIR/EBS
-#policer 3 is used. Note that this is shared with the AF41 and AF42
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 13 u32 \
-match ip tos 0x98 0xfc \
-$meter3 \
-continue flowid :3
-$TC filter add dev $INDEV parent ffff: protocol ip prio 14 u32 \
-match ip tos 0x98 0xfc \
-$meter3a \
-drop flowid :3
-#
-## *********************** BE ***************************
-##
-## Anything else (not from the AF4*) gets discarded if it
-## exceeds 1Mbps and by default goes to BE if it doesn't
-## Note that the BE class is also used by the AF4* in the worst
-## case
-##
-$TC filter add dev $INDEV parent ffff: protocol ip prio 16 u32 \
-match ip src 0/0\
-$meter4 \
-drop flowid :4
-
-######################## Egress side ########################
-
-# attach a dsmarker
-#
-$TC qdisc add $EGDEV handle 1:0 root dsmark indices 64
-#
-# values of the DSCP to change depending on the class
-#note that the ECN bits are masked out
-#
-#AF41 (0x88 is 0x22 shifted to the right by two bits)
-#
-$TC class change $EGDEV classid 1:1 dsmark mask 0x3 \
- value 0x88
-#AF42
-$TC class change $EGDEV classid 1:2 dsmark mask 0x3 \
- value 0x90
-#AF43
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x98
-#BE
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x0
-#
-#
-# The class mapping
-#
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 1 tcindex classid 1:1
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 2 tcindex classid 1:2
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 3 tcindex classid 1:3
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 4 tcindex classid 1:4
-#
-
-#
-echo "---- qdisc parameters Ingress ----------"
-$TC qdisc ls dev $INDEV
-echo "---- Class parameters Ingress ----------"
-$TC class ls dev $INDEV
-echo "---- filter parameters Ingress ----------"
-$TC filter ls dev $INDEV parent ffff:
-
-echo "---- qdisc parameters Egress ----------"
-$TC qdisc ls $EGDEV
-echo "---- Class parameters Egress ----------"
-$TC class ls $EGDEV
-echo "---- filter parameters Egress ----------"
-$TC filter ls $EGDEV parent 1:0
-#
-#deleting the ingress qdisc
-#$TC qdisc del $INDEV ingress
diff --git a/examples/diffserv/Edge32-cb-chains b/examples/diffserv/Edge32-cb-chains
deleted file mode 100644
index 88ee2ceaf57e..000000000000
--- a/examples/diffserv/Edge32-cb-chains
+++ /dev/null
@@ -1,144 +0,0 @@
-#! /bin/sh -x
-#
-# sample script on using the ingress capabilities
-# This script fwmark tags(IPchains) based on metering on the ingress
-# interface the result is used for fast classification and re-marking
-# on the egress interface
-# This is an example of a color blind mode marker with no PIR configured
-# based on draft-wahjak-mcm-00.txt (section 3.1)
-#
-#path to various utilities;
-#change to reflect yours.
-#
-IPROUTE=/root/DS-6-beta/iproute2-990530-dsing
-TC=$IPROUTE/tc/tc
-IP=$IPROUTE/ip/ip
-IPCHAINS=/root/DS-6-beta/ipchains-1.3.9/ipchains
-INDEV=eth2
-EGDEV="dev eth1"
-CIR1=1500kbit
-CIR2=500kbit
-
-#The CBS is about 60 MTU sized packets
-CBS1=90k
-CBS2=90k
-
-meter1="police rate $CIR1 burst $CBS1 "
-meter1a="police rate $CIR2 burst $CBS1 "
-meter2="police rate $CIR1 burst $CBS2 "
-meter2a="police rate $CIR2 burst $CBS2 "
-meter3="police rate $CIR2 burst $CBS1 "
-meter3a="police rate $CIR2 burst $CBS1 "
-meter4="police rate $CIR2 burst $CBS2 "
-meter5="police rate $CIR1 burst $CBS2 "
-#
-# tag the rest of incoming packets from subnet 10.2.0.0/24 to fw value 1
-# tag all incoming packets from any other subnet to fw tag 2
-############################################################
-$IPCHAINS -A input -i $INDEV -s 0/0 -m 2
-$IPCHAINS -A input -i $INDEV -s 10.2.0.0/24 -m 1
-#
-############################################################
-# install the ingress qdisc on the ingress interface
-$TC qdisc add dev $INDEV handle ffff: ingress
-#
-############################################################
-
-# All packets are marked with a tcindex value which is used on the egress
-# tcindex 1 maps to AF41, 2->AF42, 3->AF43, 4->BE
-#
-############################################################
-#
-# anything with fw tag of 1 is passed on with a tcindex value 1
-#if it doesn't exceed its allocated rate (CIR/CBS)
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 1 handle 1 fw \
-$meter1 \
-continue flowid 4:1
-$TC filter add dev $INDEV parent ffff: protocol ip prio 2 handle 1 fw \
-$meter1a \
-continue flowid 4:1
-#
-# if it exceeds the above but not the extra rate/burst below, it gets a
-#tcindex value of 2
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 3 handle 1 fw \
-$meter2 \
-continue flowid 4:2
-$TC filter add dev $INDEV parent ffff: protocol ip prio 4 handle 1 fw \
-$meter2a \
-continue flowid 4:2
-#
-# if it exceeds the above but not the rule below, it gets a tcindex value
-# of 3
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 5 handle 1 fw \
-$meter3 \
-continue flowid 4:3
-$TC filter add dev $INDEV parent ffff: protocol ip prio 6 handle 1 fw \
-$meter3a \
-drop flowid 4:3
-#
-# Anything else (not from the subnet 10.2.0.24/24) gets discarded if it
-# exceeds 1Mbps and by default goes to BE if it doesn't
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 7 handle 2 fw \
-$meter5 \
-drop flowid 4:4
-
-
-######################## Egress side ########################
-
-
-# attach a dsmarker
-#
-$TC qdisc add $EGDEV handle 1:0 root dsmark indices 64
-#
-# values of the DSCP to change depending on the class
-#note that the ECN bits are masked out
-#
-#AF41 (0x88 is 0x22 shifted to the right by two bits)
-#
-$TC class change $EGDEV classid 1:1 dsmark mask 0x3 \
- value 0x88
-#AF42
-$TC class change $EGDEV classid 1:2 dsmark mask 0x3 \
- value 0x90
-#AF43
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x98
-#BE
-$TC class change $EGDEV classid 1:4 dsmark mask 0x3 \
- value 0x0
-#
-#
-# The class mapping (using tcindex; could easily have
-# replaced it with the fw classifier instead)
-#
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 1 tcindex classid 1:1
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 2 tcindex classid 1:2
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 3 tcindex classid 1:3
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 4 tcindex classid 1:4
-#
-
-#
-echo "---- qdisc parameters Ingress ----------"
-$TC qdisc ls dev $INDEV
-echo "---- Class parameters Ingress ----------"
-$TC class ls dev $INDEV
-echo "---- filter parameters Ingress ----------"
-$TC filter ls dev $INDEV parent ffff:
-
-echo "---- qdisc parameters Egress ----------"
-$TC qdisc ls $EGDEV
-echo "---- Class parameters Egress ----------"
-$TC class ls $EGDEV
-echo "---- filter parameters Egress ----------"
-$TC filter ls $EGDEV parent 1:0
-#
-#deleting the ingress qdisc
-#$TC qdisc del $INDEV ingress
diff --git a/examples/diffserv/Edge32-cb-u32 b/examples/diffserv/Edge32-cb-u32
deleted file mode 100644
index 544941376f92..000000000000
--- a/examples/diffserv/Edge32-cb-u32
+++ /dev/null
@@ -1,145 +0,0 @@
-#! /bin/sh
-#
-# sample script on using the ingress capabilities using u32 classifier
-# This script tags tcindex based on metering on the ingress
-# interface the result is used for fast classification and re-marking
-# on the egress interface
-# This is an example of a color blind mode marker with PIR configured
-# based on draft-wahjak-mcm-00.txt (section 3.2)
-#
-#path to various utilities;
-#change to reflect yours.
-#
-IPROUTE=/root/DS-6-beta/iproute2-990530-dsing
-TC=$IPROUTE/tc/tc
-IP=$IPROUTE/ip/ip
-INDEV=eth2
-EGDEV="dev eth1"
-CIR1=1000kbit
-CIR2=1000kbit
-# The PIR is the excess (in addition to the CIR i.e if always
-# going to the PIR --> average rate is CIR+PIR)
-PIR1=1000kbit
-PIR2=500kbit
-
-#The CBS is about 60 MTU sized packets
-CBS1=90k
-CBS2=90k
-#the EBS is about 10 max sized packets
-EBS1=15k
-EBS2=15k
-# The meters
-meter1=" police rate $CIR1 burst $CBS1 "
-meter1a=" police rate $PIR1 burst $EBS1 "
-meter2=" police rate $CIR2 burst $CBS1 "
-meter2a="police rate $PIR2 burst $CBS1 "
-meter3=" police rate $CIR2 burst $CBS2 "
-meter3a=" police rate $PIR2 burst $EBS2 "
-meter4=" police rate $CIR1 burst $CBS2 "
-meter5=" police rate $CIR1 burst $CBS2 "
-
-
-# install the ingress qdisc on the ingress interface
-############################################################
-$TC qdisc add dev $INDEV handle ffff: ingress
-############################################################
-#
-############################################################
-
-# All packets are marked with a tcindex value which is used on the egress
-# NOTE: tcindex 1 maps to AF41, 2->AF42, 3->AF43, 4->BE
-#
-#anything from subnet 10.2.0.2/24 is passed on with a tcindex value 1
-#if it doesn't exceed its CIR/CBS + PIR/EBS
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 1 u32 \
-match ip src 10.2.0.0/24 $meter1 \
-continue flowid :1
-$TC filter add dev $INDEV parent ffff: protocol ip prio 2 u32 \
-match ip src 10.2.0.0/24 $meter1a \
-continue flowid :1
-
-#
-# if it exceeds the above but not the extra rate/burst below, it gets a
-#tcindex value of 2
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 3 u32 \
-match ip src 10.2.0.0/24 $meter2 \
-continue flowid :2
-$TC filter add dev $INDEV parent ffff: protocol ip prio 4 u32 \
-match ip src 10.2.0.0/24 $meter2a \
-continue flowid :2
-#
-# if it exceeds the above but not the rule below, it gets a tcindex value
-# of 3
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 5 u32 \
-match ip src 10.2.0.0/24 $meter3 \
-continue flowid :3
-$TC filter add dev $INDEV parent ffff: protocol ip prio 6 u32 \
-match ip src 10.2.0.0/24 $meter3a \
-drop flowid :3
-#
-#
-# Anything else (not from the subnet 10.2.0.24/24) gets discarded if it
-# exceeds 1Mbps and by default goes to BE if it doesn't
-#
-$TC filter add dev $INDEV parent ffff: protocol ip prio 7 u32 \
-match ip src 0/0 $meter5 \
-drop flowid :4
-
-
-######################## Egress side ########################
-
-
-# attach a dsmarker
-#
-$TC qdisc add $EGDEV handle 1:0 root dsmark indices 64
-#
-# values of the DSCP to change depending on the class
-#note that the ECN bits are masked out
-#
-#AF41 (0x88 is 0x22 shifted to the right by two bits)
-#
-$TC class change $EGDEV classid 1:1 dsmark mask 0x3 \
- value 0x88
-#AF42
-$TC class change $EGDEV classid 1:2 dsmark mask 0x3 \
- value 0x90
-#AF43
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x98
-#BE
-$TC class change $EGDEV classid 1:3 dsmark mask 0x3 \
- value 0x0
-#
-#
-# The class mapping
-#
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 1 tcindex classid 1:1
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 2 tcindex classid 1:2
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 3 tcindex classid 1:3
-$TC filter add $EGDEV parent 1:0 protocol ip prio 1 \
- handle 4 tcindex classid 1:4
-#
-
-#
-echo "---- qdisc parameters Ingress ----------"
-$TC qdisc ls dev $INDEV
-echo "---- Class parameters Ingress ----------"
-$TC class ls dev $INDEV
-echo "---- filter parameters Ingress ----------"
-$TC filter ls dev $INDEV parent ffff:
-
-echo "---- qdisc parameters Egress ----------"
-$TC qdisc ls $EGDEV
-echo "---- Class parameters Egress ----------"
-$TC class ls $EGDEV
-echo "---- filter parameters Egress ----------"
-$TC filter ls $EGDEV parent 1:0
-#
-#deleting the ingress qdisc
-#$TC qdisc del $INDEV ingress
diff --git a/examples/diffserv/README b/examples/diffserv/README
deleted file mode 100644
index ec91d632e0c9..000000000000
--- a/examples/diffserv/README
+++ /dev/null
@@ -1,98 +0,0 @@
-
-Note all these are mere examples which can be customized to your needs
-
-AFCBQ
------
-AF PHB built using CBQ, DSMARK,GRED (default in GRIO mode) ,RED for BE
-and the tcindex classifier with some algorithmic mapping
-
-EFCBQ
------
-EF PHB built using CBQ (for rate control and prioritization),
-DSMARK( to remark DSCPs), tcindex classifier and RED for the BE
-traffic.
-
-EFPRIO
-------
-EF PHB using the PRIO scheduler, Token Bucket to rate control EF,
-tcindex classifier, DSMARK to remark, and RED for the BE traffic
-
-EDGE scripts
-==============
-
-CB-3(1|2)-(u32/chains)
-======================
-
-
-The major differences are that the classifier is u32 on -u32 extension
-and IPchains on the chains extension. CB stands for color Blind
-and 31 is for the mode where only a CIR and CBS are defined whereas
-32 stands for a mode where a CIR/CBS + PIR/EBS are defined.
-
-Color Blind (CB)
-==========-----=
-We look at one special subnet that we are interested in for simplicty
-reasons to demonstrate the capability. We send the packets from that
-subnet to AF4*, BE or end up dropping depending on the metering results.
-
-
-The algorithm overview is as follows:
-
-*classify:
-
-**case: subnet X
-----------------
- if !exceed meter1 tag as AF41
- else
- if !exceed meter2 tag as AF42
- else
- if !exceed meter 3 tag as AF43
- else
- drop
-
-default case: Any other subnet
--------------------------------
- if !exceed meter 5 tag as AF43
- else
- drop
-
-
-One Egress side change the DSCPs of the packets to reflect AF4* and BE
-based on the tags from the ingress.
-
--------------------------------------------------------------
-
-Color Aware
-===========
-
-Define some meters with + policing and give them IDs eg
-
-meter1=police index 1 rate $CIR1 burst $CBS1
-meter2=police index 2 rate $CIR2 burst $CBS2 etc
-
-General overview:
-classify based on the DSCPs and use the policer ids to decide tagging
-
-
-*classify on ingress:
-
-switch (dscp) {
- case AF41: /* tos&0xfc == 0x88 */
- if (!exceed meter1) break;
- case AF42: /* tos&0xfc == 0x90 */
- if (!exceed meter2) {
- tag as AF42;
- break;
- }
- case AF43: /* tos&0xfc == 0x98 */
- if (!exceed meter3) {
- tag as AF43;
- break;
- } else
- drop;
- default:
- if (!exceed meter4) tag as BE;
- else drop;
-}
-
-On the Egress side mark the proper AF tags
diff --git a/examples/diffserv/afcbq b/examples/diffserv/afcbq
deleted file mode 100644
index 10d6d934486f..000000000000
--- a/examples/diffserv/afcbq
+++ /dev/null
@@ -1,105 +0,0 @@
-#!/usr/bin/perl
-#
-#
-# AF using CBQ for a single interface eth0
-# 4 AF classes using GRED and one BE using RED
-# Things you might want to change:
-# - the device bandwidth (set at 10Mbits)
-# - the bandwidth allocated for each AF class and the BE class
-# - the drop probability associated with each AF virtual queue
-#
-# AF DSCP values used (based on AF draft 04)
-# -----------------------------------------
-# AF DSCP values
-# AF1 1. 0x0a 2. 0x0c 3. 0x0e
-# AF2 1. 0x12 2. 0x14 3. 0x16
-# AF3 1. 0x1a 2. 0x1c 3. 0x1e
-# AF4 1. 0x22 2. 0x24 3. 0x26
-
-#
-#
-# A simple DSCP-class relationship formula used to generate
-# values in the for loop of this script; $drop stands for the
-# DP
-# $dscp = ($class*8+$drop*2)
-#
-# if you use GRIO buffer sharing, then GRED priority is set as follows:
-# $gprio=$drop+1;
-#
-
-$TC = "/usr/src/iproute2-current/tc/tc";
-$DEV = "dev lo";
-$DEV = "dev eth1";
-$DEV = "dev eth0";
-# the BE-class number
-$beclass = "5";
-
-#GRIO buffer sharing on or off?
-$GRIO = "";
-$GRIO = "grio";
-# The bandwidth of your device
-$linerate="10Mbit";
-# The BE and AF rates
-%rate_table=();
-$berate="1500Kbit";
-$rate_table{"AF1rate"}="1500Kbit";
-$rate_table{"AF2rate"}="1500Kbit";
-$rate_table{"AF3rate"}="1500Kbit";
-$rate_table{"AF4rate"}="1500Kbit";
-#
-#
-#
-print "\n# --- General setup ---\n";
-print "$TC qdisc add $DEV handle 1:0 root dsmark indices 64 set_tc_index\n";
-print "$TC filter add $DEV parent 1:0 protocol ip prio 1 tcindex mask 0xfc " .
- "shift 2 pass_on\n";
- #"shift 2\n";
-print "$TC qdisc add $DEV parent 1:0 handle 2:0 cbq bandwidth $linerate ".
- "cell 8 avpkt 1000 mpu 64\n";
-print "$TC filter add $DEV parent 2:0 protocol ip prio 1 tcindex ".
- "mask 0xf0 shift 4 pass_on\n";
-for $class (1..4) {
- print "\n# --- AF Class $class specific setup---\n";
- $AFrate=sprintf("AF%drate",$class);
- print "$TC class add $DEV parent 2:0 classid 2:$class cbq ".
- "bandwidth $linerate rate $rate_table{$AFrate} avpkt 1000 prio ".
- (6-$class)." bounded allot 1514 weight 1 maxburst 21\n";
- print "$TC filter add $DEV parent 2:0 protocol ip prio 1 handle $class ".
- "tcindex classid 2:$class\n";
- print "$TC qdisc add $DEV parent 2:$class gred setup DPs 3 default 2 ".
- "$GRIO\n";
-#
-# per DP setup
-#
- for $drop (1..3) {
- print "\n# --- AF Class $class DP $drop---\n";
- $dscp = $class*8+$drop*2;
- $tcindex = sprintf("1%x%x",$class,$drop);
- print "$TC filter add $DEV parent 1:0 protocol ip prio 1 ".
- "handle $dscp tcindex classid 1:$tcindex\n";
- $prob = $drop*0.02;
- if ($GRIO) {
- $gprio = $drop+1;
- print "$TC qdisc change $DEV parent 2:$class gred limit 60KB min 15KB ".
- "max 45KB burst 20 avpkt 1000 bandwidth $linerate DP $drop ".
- "probability $prob ".
- "prio $gprio\n";
- } else {
- print "$TC qdisc change $DEV parent 2:$class gred limit 60KB min 15KB ".
- "max 45KB burst 20 avpkt 1000 bandwidth $linerate DP $drop ".
- "probability $prob \n";
- }
- }
-}
-#
-#
-print "\n#------BE Queue setup------\n";
-print "$TC filter add $DEV parent 1:0 protocol ip prio 2 ".
- "handle 0 tcindex mask 0 classid 1:1\n";
-print "$TC class add $DEV parent 2:0 classid 2:$beclass cbq ".
- "bandwidth $linerate rate $berate avpkt 1000 prio 6 " .
- "bounded allot 1514 weight 1 maxburst 21 \n";
-print "$TC filter add $DEV parent 2:0 protocol ip prio 1 handle 0 tcindex ".
- "classid 2:5\n";
-print "$TC qdisc add $DEV parent 2:5 red limit 60KB min 15KB max 45KB ".
- "burst 20 avpkt 1000 bandwidth $linerate probability 0.4\n";
diff --git a/examples/diffserv/ef-prio b/examples/diffserv/ef-prio
deleted file mode 100644
index 48611bdd65e8..000000000000
--- a/examples/diffserv/ef-prio
+++ /dev/null
@@ -1,25 +0,0 @@
-#!/usr/bin/perl
-$TC = "/root/DS-6-beta/iproute2-990530-dsing/tc/tc";
-$DEV = "dev eth1";
-$efrate="1.5Mbit";
-$MTU="1.5kB";
-print "$TC qdisc add $DEV handle 1:0 root dsmark indices 64 set_tc_index\n";
-print "$TC filter add $DEV parent 1:0 protocol ip prio 1 tcindex ".
- "mask 0xfc shift 2\n";
-print "$TC qdisc add $DEV parent 1:0 handle 2:0 prio\n";
-#
-# EF class: Maximum about one MTU sized packet allowed on the queue
-#
-print "$TC qdisc add $DEV parent 2:1 tbf rate $efrate burst $MTU limit 1.6kB\n";
-print "$TC filter add $DEV parent 2:0 protocol ip prio 1 ".
- "handle 0x2e tcindex classid 2:1 pass_on\n";
-#
-# BE class
-#
-print "#BE class(2:2) \n";
-print "$TC qdisc add $DEV parent 2:2 red limit 60KB ".
- "min 15KB max 45KB burst 20 avpkt 1000 bandwidth 10Mbit ".
- "probability 0.4\n";
-#
-print "$TC filter add $DEV parent 2:0 protocol ip prio 2 ".
- "handle 0 tcindex mask 0 classid 2:2 pass_on\n";
diff --git a/examples/diffserv/efcbq b/examples/diffserv/efcbq
deleted file mode 100644
index bcc437b3d229..000000000000
--- a/examples/diffserv/efcbq
+++ /dev/null
@@ -1,31 +0,0 @@
-#!/usr/bin/perl
-#
-$TC = "/root/DS-6-beta/iproute2-990530-dsing/tc/tc";
-$DEV = "dev eth1";
-print "$TC qdisc add $DEV handle 1:0 root dsmark indices 64 set_tc_index\n";
-print "$TC filter add $DEV parent 1:0 protocol ip prio 1 tcindex ".
- "mask 0xfc shift 2\n";
-print "$TC qdisc add $DEV parent 1:0 handle 2:0 cbq bandwidth ".
- "10Mbit cell 8 avpkt 1000 mpu 64\n";
-#
-# EF class
-#
-print "$TC class add $DEV parent 2:0 classid 2:1 cbq bandwidth ".
- "10Mbit rate 1500Kbit avpkt 1000 prio 1 bounded isolated ".
- "allot 1514 weight 1 maxburst 10 \n";
-# packet fifo for EF?
-print "$TC qdisc add $DEV parent 2:1 pfifo limit 5\n";
-print "$TC filter add $DEV parent 2:0 protocol ip prio 1 ".
- "handle 0x2e tcindex classid 2:1 pass_on\n";
-#
-# BE class
-#
-print "#BE class(2:2) \n";
-print "$TC class add $DEV parent 2:0 classid 2:2 cbq bandwidth ".
- "10Mbit rate 5Mbit avpkt 1000 prio 7 allot 1514 weight 1 ".
- "maxburst 21 borrow split 2:0 defmap 0xffff \n";
-print "$TC qdisc add $DEV parent 2:2 red limit 60KB ".
- "min 15KB max 45KB burst 20 avpkt 1000 bandwidth 10Mbit ".
- "probability 0.4\n";
-print "$TC filter add $DEV parent 2:0 protocol ip prio 2 ".
- "handle 0 tcindex mask 0 classid 2:2 pass_on\n";
diff --git a/examples/diffserv/regression-testing b/examples/diffserv/regression-testing
deleted file mode 100644
index d50f4c8a3b5a..000000000000
--- a/examples/diffserv/regression-testing
+++ /dev/null
@@ -1,125 +0,0 @@
-
-These were the tests done to validate the Diffserv scripts.
-This document will be updated continuously. If you do more
-thorough validation testing please post the details to the
-diffserv mailing list.
-Nevertheless, these tests should serve for basic validation.
-
-AFCBQ, EFCBQ, EFPRIO
-----------------------
-
-generate all possible DSCPs and observe that they
-get sent to the proper classes. In the case of AF also
-to the correct Virtual Queues.
-
-Edge1
------
-generate TOS values 0x0,0x10,0xbb each with IP addresses
-10.2.0.24 (mark 1), 10.2.0.3 (mark2) and 10.2.0.30 (mark 3)
-and observe that they get marked as expected.
-
-Edge2
------
-
--Repeat the tests in Edge1
--ftp with data direction from 10.2.0.2
- *observe that the metering/policing works correctly (and the marking
- as well). In this case the mark used will be 3
-
-Edge31-cb-chains
-----------------
-
--ftp with data direction from 10.2.0.2
-
- *observe that the metering/policing works correctly (and the marking
- as well). In this case the mark used will be 1.
-
- Metering: The data throughput should not exceed 2*CIR1 + 2*CIR2
- which is roughly: 5mbps
-
- Marking: the should be a variation of marked packets:
- AF41(TOS=0x88) AF42(0x90) AF43(0x98) and BE (0x0)
-
-More tests required to see the interaction of several sources (other
-than subnet 10.2.0.0/24).
-
-Edge31-ca-u32
---------------
-
-Generate data using modified tcpblast from 10.2.0.2 (behind eth2) to the
-discard port of 10.1.0.2 (behind eth1)
-
-1) generate with src tos = 0x88
- Metering: Allocated throughput should not exceed 2*CIR1 + 2*CIR2
- approximately 5mbps
- Marking: Should vary between 0x88,0x90,0x98 and 0x0
-
-2) generate with src tos = 0x90
- Metering: Allocated throughput should not exceed CIR1 + 2*CIR2
- approximately 3.5mbps
- Marking: Should vary between 0x90,0x98 and 0x0
-
-3) generate with src tos = 0x98
- Metering: Allocated throughput should not exceed CIR1 + CIR2
- approximately 2.5mbps
- Marking: Should vary between 0x98 and 0x0
-
-4) generate with src tos any other than the above
- Metering: Allocated throughput should not exceed CIR1
- approximately 1.5mbps
- Marking: Should be consistent at 0x0
-
-TODO: Testing on how each color shares when all 4 types of packets
-are going through the edge device
-
-Edge32-cb-u32, Edge32-cb-chains
--------------------------------
-
--ftp with data direction from 10.2.0.2
-
- *observe that the metering/policing works correctly (and the marking
- as well).
-
- Metering:
- The data throughput should not exceed 2*CIR1 + 2*CIR2
- + 2*PIR2 + PIR1 for u32 which is roughly: 6mbps
- The data throughput should not exceed 2*CIR1 + 5*CIR2
- for chains which is roughly: 6mbps
-
- Marking: the should be a variation of marked packets:
- AF41(TOS=0x88) AF42(0x90) AF43(0x98) and BE (0x0)
-
-TODO:
--More tests required to see the interaction of several sources (other
-than subnet 10.2.0.0/24).
--More tests needed to capture stats on how many times the CIR was exceeded
-but the data was not remarked etc.
-
-Edge32-ca-u32
---------------
-
-Generate data using modified tcpblast from 10.2.0.2 (behind eth2) to the
-discard port of 10.1.0.2 (behind eth1)
-
-1) generate with src tos = 0x88
- Metering: Allocated throughput should not exceed 2*CIR1 + 2*CIR2
- +PIR1 -- approximately 4mbps
- Marking: Should vary between 0x88,0x90,0x98 and 0x0
-
-2) generate with src tos = 0x90
- Metering: Allocated throughput should not exceed CIR1 + 2*CIR2
- + 2* PIR2 approximately 3mbps
- Marking: Should vary between 0x90,0x98 and 0x0
-
-3) generate with src tos = 0x98
- Metering: Allocated throughput should not exceed PIR1+ CIR1 + CIR2
- approximately 2.5mbps
- Marking: Should vary between 0x98 and 0x0
-
-4) generate with src tos any other than the above
- Metering: Allocated throughput should not exceed CIR1
- approximately 1mbps
- Marking: Should be consistent at 0x0
-
-TODO: Testing on how each color shares when all 4 types of packets
-are going through the edge device
--
2.20.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
end of thread, other threads:[~2019-10-23 16:16 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-23 16:16 [PATCH iproute2 0/3] remove old examples Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 1/3] examples: remove out of date cbq stuff Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 2/3] examples: remove gaiconf Stephen Hemminger
2019-10-23 16:16 ` [PATCH iproute2 3/3] examples: remove diffserv Stephen Hemminger
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.