[PATCH v2 0/6] net: phy: at803x device tree binding

[PATCH v2 0/6] net: phy: at803x device tree binding

[Michael Walle]

Adds a device tree binding to configure the clock and the RGMII voltage.

Changes since v1:
 - rebased to latest net-next
 - renamed "Atheros" to "Qualcomm Atheros"
 - add a new patch to remove config_init() from AR9331

Changes since the RFC:
 - renamed the Kconfig entry to "Qualcomm Atheros.." and reordered the
   item
 - renamed the prefix from atheros to qca
 - use the correct name AR803x (instead of AT803x) in new files and
   dt-bindings.
 - listed the PHY maintainers in the new schema. Hopefully, thats ok.
 - fixed a typo in the bindings schema
 - run dtb_checks and dt_binding_check and fixed the schema
 - dropped the rgmii-io-1v8 property; instead provide two regulators vddh
   and vddio, add one consumer vddio-supply
 - fix the clock settings for the AR8030/AR8035
 - only the AR8031 supports chaning the LDO and the PLL mode in software.
   Check if we have the correct PHY.
 - new patch to mention the AR8033 which is the same as the AR8031 just
   without PTP support
 - new patch which corrects any displayed PHY names and comments. Be
   consistent.

Michael Walle (6):
  net: phy: at803x: fix Kconfig description
  dt-bindings: net: phy: Add support for AT803X
  net: phy: at803x: add device tree binding
  net: phy: at803x: mention AR8033 as same as AR8031
  net: phy: at803x: fix the PHY names
  net: phy: at803x: remove config_init for AR9331

 .../devicetree/bindings/net/qca,ar803x.yaml   | 111 ++++++
 MAINTAINERS                                   |   2 +
 drivers/net/phy/Kconfig                       |  10 +-
 drivers/net/phy/at803x.c                      | 321 +++++++++++++++++-
 include/dt-bindings/net/qca-ar803x.h          |  13 +
 5 files changed, 441 insertions(+), 16 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/qca,ar803x.yaml
 create mode 100644 include/dt-bindings/net/qca-ar803x.h

-- 
2.20.1

[PATCH v2 1/6] net: phy: at803x: fix Kconfig description

[Michael Walle]

The name of the PHY is actually AR803x not AT803x. Additionally, add the
name of the vendor and mention the AR8031 support.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
 drivers/net/phy/Kconfig | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index fe602648b99f..1b884ebb4e48 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -282,11 +282,6 @@ config AX88796B_PHY
 	  Currently supports the Asix Electronics PHY found in the X-Surf 100
 	  AX88796B package.
 
-config AT803X_PHY
-	tristate "AT803X PHYs"
-	---help---
-	  Currently supports the AT8030 and AT8035 model
-
 config BCM63XX_PHY
 	tristate "Broadcom 63xx SOCs internal PHY"
 	depends on BCM63XX || COMPILE_TEST
@@ -444,6 +439,11 @@ config NXP_TJA11XX_PHY
 	---help---
 	  Currently supports the NXP TJA1100 and TJA1101 PHY.
 
+config AT803X_PHY
+	tristate "Qualcomm Atheros AR803X PHYs"
+	help
+	  Currently supports the AR8030, AR8031 and AR8035 model
+
 config QSEMI_PHY
 	tristate "Quality Semiconductor PHYs"
 	---help---
-- 
2.20.1

[PATCH v2 2/6] dt-bindings: net: phy: Add support for AT803X

[Michael Walle]

Document the Atheros AR803x PHY bindings.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/net/qca,ar803x.yaml   | 111 ++++++++++++++++++
 MAINTAINERS                                   |   2 +
 include/dt-bindings/net/qca-ar803x.h          |  13 ++
 3 files changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/qca,ar803x.yaml
 create mode 100644 include/dt-bindings/net/qca-ar803x.h

diff --git a/Documentation/devicetree/bindings/net/qca,ar803x.yaml b/Documentation/devicetree/bindings/net/qca,ar803x.yaml
new file mode 100644
index 000000000000..5a6c9d20c0ba
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qca,ar803x.yaml
@@ -0,0 +1,111 @@
+# SPDX-License-Identifier: GPL-2.0+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/qca,ar803x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Atheros AR803x PHY
+
+maintainers:
+  - Andrew Lunn <andrew@lunn.ch>
+  - Florian Fainelli <f.fainelli@gmail.com>
+  - Heiner Kallweit <hkallweit1@gmail.com>
+
+description: |
+  Bindings for Qualcomm Atheros AR803x PHYs
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+
+properties:
+  qca,clk-out-frequency:
+    description: Clock output frequency in Hertz.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 25000000, 50000000, 62500000, 125000000 ]
+
+  qca,clk-out-strength:
+    description: Clock output driver strength.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 1, 2 ]
+
+  qca,keep-pll-enabled:
+    description: |
+      If set, keep the PLL enabled even if there is no link. Useful if you
+      want to use the clock output without an ethernet link.
+
+      Only supported on the AR8031.
+    type: boolean
+
+  vddio-supply:
+    description: |
+      RGMII I/O voltage regulator (see regulator/regulator.yaml).
+
+      The PHY supports RGMII I/O voltages of 1.5V, 1.8V and 2.5V. You can
+      either connect this to the vddio-regulator (1.5V / 1.8V) or the
+      vddh-regulator (2.5V).
+
+      Only supported on the AR8031.
+
+  vddio-regulator:
+    type: object
+    description:
+      Initial data for the VDDIO regulator. Set this to 1.5V or 1.8V.
+    allOf:
+      - $ref: /schemas/regulator/regulator.yaml
+
+  vddh-regulator:
+    type: object
+    description:
+      Dummy subnode to model the external connection of the PHY VDDH
+      regulator to VDDIO.
+    allOf:
+      - $ref: /schemas/regulator/regulator.yaml
+
+
+examples:
+  - |
+    #include <dt-bindings/net/qca-ar803x.h>
+
+    ethernet {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        phy-mode = "rgmii-id";
+
+        ethernet-phy@0 {
+            reg = <0>;
+
+            qca,clk-out-frequency = <125000000>;
+            qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+
+            vddio-supply = <&vddio>;
+
+            vddio: vddio-regulator {
+                regulator-min-microvolt = <1800000>;
+                regulator-max-microvolt = <1800000>;
+            };
+        };
+    };
+  - |
+    #include <dt-bindings/net/qca-ar803x.h>
+
+    ethernet {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        phy-mode = "rgmii-id";
+
+        ethernet-phy@0 {
+            reg = <0>;
+
+            qca,clk-out-frequency = <50000000>;
+            qca,keep-pll-enabled;
+
+            vddio-supply = <&vddh>;
+
+            vddh: vddh-regulator {
+            };
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index c0024b296158..709c60aacb58 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6155,10 +6155,12 @@ S:	Maintained
 F:	Documentation/ABI/testing/sysfs-class-net-phydev
 F:	Documentation/devicetree/bindings/net/ethernet-phy.yaml
 F:	Documentation/devicetree/bindings/net/mdio*
+F:	Documentation/devicetree/bindings/net/qca,ar803x.yaml
 F:	Documentation/networking/phy.rst
 F:	drivers/net/phy/
 F:	drivers/of/of_mdio.c
 F:	drivers/of/of_net.c
+F:	include/dt-bindings/net/qca-ar803x.h
 F:	include/linux/*mdio*.h
 F:	include/linux/of_net.h
 F:	include/linux/phy.h
diff --git a/include/dt-bindings/net/qca-ar803x.h b/include/dt-bindings/net/qca-ar803x.h
new file mode 100644
index 000000000000..9c046c7242ed
--- /dev/null
+++ b/include/dt-bindings/net/qca-ar803x.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Device Tree constants for the Qualcomm Atheros AR803x PHYs
+ */
+
+#ifndef _DT_BINDINGS_QCA_AR803X_H
+#define _DT_BINDINGS_QCA_AR803X_H
+
+#define AR803X_STRENGTH_FULL		0
+#define AR803X_STRENGTH_HALF		1
+#define AR803X_STRENGTH_QUARTER		2
+
+#endif
-- 
2.20.1

[PATCH v2 3/6] net: phy: at803x: add device tree binding

[Michael Walle]

Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
 drivers/net/phy/at803x.c | 301 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 300 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 8e30db28fd7d..aa782b28615b 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -13,7 +13,12 @@
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
 #include <linux/of_gpio.h>
+#include <linux/bitfield.h>
 #include <linux/gpio/consumer.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/consumer.h>
+#include <dt-bindings/net/qca-ar803x.h>
 
 #define AT803X_SPECIFIC_STATUS			0x11
 #define AT803X_SS_SPEED_MASK			(3 << 14)
@@ -62,6 +67,42 @@
 #define AT803X_DEBUG_REG_5			0x05
 #define AT803X_DEBUG_TX_CLK_DLY_EN		BIT(8)
 
+#define AT803X_DEBUG_REG_1F			0x1F
+#define AT803X_DEBUG_PLL_ON			BIT(2)
+#define AT803X_DEBUG_RGMII_1V8			BIT(3)
+
+/* AT803x supports either the XTAL input pad, an internal PLL or the
+ * DSP as clock reference for the clock output pad. The XTAL reference
+ * is only used for 25 MHz output, all other frequencies need the PLL.
+ * The DSP as a clock reference is used in synchronous ethernet
+ * applications.
+ *
+ * By default the PLL is only enabled if there is a link. Otherwise
+ * the PHY will go into low power state and disabled the PLL. You can
+ * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always
+ * enabled.
+ */
+#define AT803X_MMD7_CLK25M			0x8016
+#define AT803X_CLK_OUT_MASK			GENMASK(4, 2)
+#define AT803X_CLK_OUT_25MHZ_XTAL		0
+#define AT803X_CLK_OUT_25MHZ_DSP		1
+#define AT803X_CLK_OUT_50MHZ_PLL		2
+#define AT803X_CLK_OUT_50MHZ_DSP		3
+#define AT803X_CLK_OUT_62_5MHZ_PLL		4
+#define AT803X_CLK_OUT_62_5MHZ_DSP		5
+#define AT803X_CLK_OUT_125MHZ_PLL		6
+#define AT803X_CLK_OUT_125MHZ_DSP		7
+
+/* The AR8035 has another mask which is compatible with the AR8031 mask but
+ * doesn't support choosing between XTAL/PLL and DSP.
+ */
+#define AT8035_CLK_OUT_MASK			GENMASK(4, 3)
+
+#define AT803X_CLK_OUT_STRENGTH_MASK		GENMASK(8, 7)
+#define AT803X_CLK_OUT_STRENGTH_FULL		0
+#define AT803X_CLK_OUT_STRENGTH_HALF		1
+#define AT803X_CLK_OUT_STRENGTH_QUARTER		2
+
 #define ATH9331_PHY_ID 0x004dd041
 #define ATH8030_PHY_ID 0x004dd076
 #define ATH8031_PHY_ID 0x004dd074
@@ -72,6 +113,16 @@ MODULE_DESCRIPTION("Atheros 803x PHY driver");
 MODULE_AUTHOR("Matus Ujhelyi");
 MODULE_LICENSE("GPL");
 
+struct at803x_priv {
+	int flags;
+#define AT803X_KEEP_PLL_ENABLED	BIT(0)	/* don't turn off internal PLL */
+	u16 clk_25m_reg;
+	u16 clk_25m_mask;
+	struct regulator_dev *vddio_rdev;
+	struct regulator_dev *vddh_rdev;
+	struct regulator *vddio;
+};
+
 struct at803x_context {
 	u16 bmcr;
 	u16 advertise;
@@ -237,6 +288,238 @@ static int at803x_resume(struct phy_device *phydev)
 	return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0);
 }
 
+static int at803x_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev,
+					    unsigned int selector)
+{
+	struct phy_device *phydev = rdev_get_drvdata(rdev);
+
+	if (selector)
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     0, AT803X_DEBUG_RGMII_1V8);
+	else
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     AT803X_DEBUG_RGMII_1V8, 0);
+}
+
+static int at803x_rgmii_reg_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct phy_device *phydev = rdev_get_drvdata(rdev);
+	int val;
+
+	val = at803x_debug_reg_read(phydev, AT803X_DEBUG_REG_1F);
+	if (val < 0)
+		return val;
+
+	return (val & AT803X_DEBUG_RGMII_1V8) ? 1 : 0;
+}
+
+static struct regulator_ops vddio_regulator_ops = {
+	.list_voltage = regulator_list_voltage_table,
+	.set_voltage_sel = at803x_rgmii_reg_set_voltage_sel,
+	.get_voltage_sel = at803x_rgmii_reg_get_voltage_sel,
+};
+
+static const unsigned int vddio_voltage_table[] = {
+	1500000,
+	1800000,
+};
+
+static const struct regulator_desc vddio_desc = {
+	.name = "vddio",
+	.of_match = of_match_ptr("vddio-regulator"),
+	.n_voltages = ARRAY_SIZE(vddio_voltage_table),
+	.volt_table = vddio_voltage_table,
+	.ops = &vddio_regulator_ops,
+	.type = REGULATOR_VOLTAGE,
+	.owner = THIS_MODULE,
+};
+
+static struct regulator_ops vddh_regulator_ops = {
+};
+
+static const struct regulator_desc vddh_desc = {
+	.name = "vddh",
+	.of_match = of_match_ptr("vddh-regulator"),
+	.n_voltages = 1,
+	.fixed_uV = 2500000,
+	.ops = &vddh_regulator_ops,
+	.type = REGULATOR_VOLTAGE,
+	.owner = THIS_MODULE,
+};
+
+static int at8031_register_regulators(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	struct device *dev = &phydev->mdio.dev;
+	struct regulator_config config = { };
+
+	config.dev = dev;
+	config.driver_data = phydev;
+
+	priv->vddio_rdev = devm_regulator_register(dev, &vddio_desc, &config);
+	if (IS_ERR(priv->vddio_rdev)) {
+		phydev_err(phydev, "failed to register VDDIO regulator\n");
+		return PTR_ERR(priv->vddio_rdev);
+	}
+
+	priv->vddh_rdev = devm_regulator_register(dev, &vddh_desc, &config);
+	if (IS_ERR(priv->vddh_rdev)) {
+		phydev_err(phydev, "failed to register VDDH regulator\n");
+		return PTR_ERR(priv->vddh_rdev);
+	}
+
+	return 0;
+}
+
+static bool at803x_match_phy_id(struct phy_device *phydev, u32 phy_id)
+{
+	return (phydev->phy_id & phydev->drv->phy_id_mask)
+		== (phy_id & phydev->drv->phy_id_mask);
+}
+
+static int at803x_parse_dt(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	struct at803x_priv *priv = phydev->priv;
+	unsigned int sel, mask;
+	u32 freq, strength;
+	int ret;
+
+	if (!IS_ENABLED(CONFIG_OF_MDIO))
+		return 0;
+
+	ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq);
+	if (!ret) {
+		mask = AT803X_CLK_OUT_MASK;
+		switch (freq) {
+		case 25000000:
+			sel = AT803X_CLK_OUT_25MHZ_XTAL;
+			break;
+		case 50000000:
+			sel = AT803X_CLK_OUT_50MHZ_PLL;
+			break;
+		case 62500000:
+			sel = AT803X_CLK_OUT_62_5MHZ_PLL;
+			break;
+		case 125000000:
+			sel = AT803X_CLK_OUT_125MHZ_PLL;
+			break;
+		default:
+			phydev_err(phydev, "invalid qca,clk-out-frequency\n");
+			return -EINVAL;
+		}
+
+		priv->clk_25m_reg |= FIELD_PREP(mask, sel);
+		priv->clk_25m_mask |= mask;
+
+		/* Fixup for the AR8030/AR8035. This chip has another mask and
+		 * doesn't support the DSP reference. Eg. the lowest bit of the
+		 * mask. The upper two bits select the same frequencies. Mask
+		 * the lowest bit here.
+		 *
+		 * Warning:
+		 *   There was no datasheet for the AR8030 available so this is
+		 *   just a guess. But the AR8035 is listed as pin compatible
+		 *   to the AR8030 so there might be a good chance it works on
+		 *   the AR8030 too.
+		 */
+		if (at803x_match_phy_id(phydev, ATH8030_PHY_ID) ||
+		    at803x_match_phy_id(phydev, ATH8035_PHY_ID)) {
+			priv->clk_25m_reg &= ~AT8035_CLK_OUT_MASK;
+			priv->clk_25m_mask &= ~AT8035_CLK_OUT_MASK;
+		}
+	}
+
+	ret = of_property_read_u32(node, "qca,clk-out-strength", &strength);
+	if (!ret) {
+		priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK;
+		switch (strength) {
+		case AR803X_STRENGTH_FULL:
+			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL;
+			break;
+		case AR803X_STRENGTH_HALF:
+			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF;
+			break;
+		case AR803X_STRENGTH_QUARTER:
+			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER;
+			break;
+		default:
+			phydev_err(phydev, "invalid qca,clk-out-strength\n");
+			return -EINVAL;
+		}
+	}
+
+	/* Only supported on AR8031, the AR8030/AR8035 use strapping options */
+	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+		if (of_property_read_bool(node, "qca,keep-pll-enabled"))
+			priv->flags |= AT803X_KEEP_PLL_ENABLED;
+
+		ret = at8031_register_regulators(phydev);
+		if (ret < 0)
+			return ret;
+
+		priv->vddio = devm_regulator_get_optional(&phydev->mdio.dev,
+							  "vddio");
+		if (IS_ERR(priv->vddio)) {
+			phydev_err(phydev, "failed to get VDDIO regulator\n");
+			return PTR_ERR(priv->vddio);
+		}
+
+		ret = regulator_enable(priv->vddio);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int at803x_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct at803x_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	phydev->priv = priv;
+
+	return at803x_parse_dt(phydev);
+}
+
+static int at803x_clk_out_config(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	int val;
+
+	if (!priv->clk_25m_mask)
+		return 0;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M);
+	if (val < 0)
+		return val;
+
+	val &= ~priv->clk_25m_mask;
+	val |= priv->clk_25m_reg;
+
+	return phy_write_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M, val);
+}
+
+static int at8031_pll_config(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+
+	/* The default after hardware reset is PLL OFF. After a soft reset, the
+	 * values are retained.
+	 */
+	if (priv->flags & AT803X_KEEP_PLL_ENABLED)
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     0, AT803X_DEBUG_PLL_ON);
+	else
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     AT803X_DEBUG_PLL_ON, 0);
+}
+
 static int at803x_config_init(struct phy_device *phydev)
 {
 	int ret;
@@ -259,8 +542,20 @@ static int at803x_config_init(struct phy_device *phydev)
 		ret = at803x_enable_tx_delay(phydev);
 	else
 		ret = at803x_disable_tx_delay(phydev);
+	if (ret < 0)
+		return ret;
 
-	return ret;
+	ret = at803x_clk_out_config(phydev);
+	if (ret < 0)
+		return ret;
+
+	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+		ret = at8031_pll_config(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
 }
 
 static int at803x_ack_interrupt(struct phy_device *phydev)
@@ -413,6 +708,7 @@ static struct phy_driver at803x_driver[] = {
 	.phy_id			= ATH8035_PHY_ID,
 	.name			= "Atheros 8035 ethernet",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
+	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
 	.set_wol		= at803x_set_wol,
 	.get_wol		= at803x_get_wol,
@@ -427,6 +723,7 @@ static struct phy_driver at803x_driver[] = {
 	.phy_id			= ATH8030_PHY_ID,
 	.name			= "Atheros 8030 ethernet",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
+	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
 	.link_change_notify	= at803x_link_change_notify,
 	.set_wol		= at803x_set_wol,
@@ -441,6 +738,7 @@ static struct phy_driver at803x_driver[] = {
 	.phy_id			= ATH8031_PHY_ID,
 	.name			= "Atheros 8031 ethernet",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
+	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
 	.set_wol		= at803x_set_wol,
 	.get_wol		= at803x_get_wol,
@@ -455,6 +753,7 @@ static struct phy_driver at803x_driver[] = {
 	/* ATHEROS AR9331 */
 	PHY_ID_MATCH_EXACT(ATH9331_PHY_ID),
 	.name			= "Atheros AR9331 built-in PHY",
+	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
 	.suspend		= at803x_suspend,
 	.resume			= at803x_resume,
-- 
2.20.1

[PATCH v2 4/6] net: phy: at803x: mention AR8033 as same as AR8031

[Michael Walle]

The AR8033 is the AR8031 without PTP support. All other registers are
the same. Unfortunately, they share the same PHY ID. Therefore, we
cannot distinguish between the one with PTP support and the one without.

Signed-off-by: Michael Walle <michael@walle.cc>
---
 drivers/net/phy/Kconfig  |  2 +-
 drivers/net/phy/at803x.c | 12 +++++++-----
 2 files changed, 8 insertions(+), 6 deletions(-)

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 1b884ebb4e48..8bccadf17e60 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -442,7 +442,7 @@ config NXP_TJA11XX_PHY
 config AT803X_PHY
 	tristate "Qualcomm Atheros AR803X PHYs"
 	help
-	  Currently supports the AR8030, AR8031 and AR8035 model
+	  Currently supports the AR8030, AR8031, AR8033 and AR8035 model
 
 config QSEMI_PHY
 	tristate "Quality Semiconductor PHYs"
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index aa782b28615b..716672edd415 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -93,8 +93,8 @@
 #define AT803X_CLK_OUT_125MHZ_PLL		6
 #define AT803X_CLK_OUT_125MHZ_DSP		7
 
-/* The AR8035 has another mask which is compatible with the AR8031 mask but
- * doesn't support choosing between XTAL/PLL and DSP.
+/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask
+ * but doesn't support choosing between XTAL/PLL and DSP.
  */
 #define AT8035_CLK_OUT_MASK			GENMASK(4, 3)
 
@@ -449,7 +449,9 @@ static int at803x_parse_dt(struct phy_device *phydev)
 		}
 	}
 
-	/* Only supported on AR8031, the AR8030/AR8035 use strapping options */
+	/* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping
+	 * options.
+	 */
 	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
 		if (of_property_read_bool(node, "qca,keep-pll-enabled"))
 			priv->flags |= AT803X_KEEP_PLL_ENABLED;
@@ -734,9 +736,9 @@ static struct phy_driver at803x_driver[] = {
 	.ack_interrupt		= at803x_ack_interrupt,
 	.config_intr		= at803x_config_intr,
 }, {
-	/* ATHEROS 8031 */
+	/* ATHEROS 8031/8033 */
 	.phy_id			= ATH8031_PHY_ID,
-	.name			= "Atheros 8031 ethernet",
+	.name			= "Atheros 8031/8033 ethernet",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
 	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
-- 
2.20.1

[PATCH v2 5/6] net: phy: at803x: fix the PHY names

[Michael Walle]

Fix at least the displayed strings. The actual name of the chip is
AR803x.

Signed-off-by: Michael Walle <michael@walle.cc>
---
 drivers/net/phy/at803x.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 716672edd415..4434d501cd4f 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -2,7 +2,7 @@
 /*
  * drivers/net/phy/at803x.c
  *
- * Driver for Atheros 803x PHY
+ * Driver for Qualcomm Atheros AR803x PHY
  *
  * Author: Matus Ujhelyi <ujhelyi.m@gmail.com>
  */
@@ -109,7 +109,7 @@
 #define ATH8035_PHY_ID 0x004dd072
 #define AT803X_PHY_ID_MASK			0xffffffef
 
-MODULE_DESCRIPTION("Atheros 803x PHY driver");
+MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver");
 MODULE_AUTHOR("Matus Ujhelyi");
 MODULE_LICENSE("GPL");
 
@@ -706,9 +706,9 @@ static int at803x_read_status(struct phy_device *phydev)
 
 static struct phy_driver at803x_driver[] = {
 {
-	/* ATHEROS 8035 */
+	/* Qualcomm Atheros AR8035 */
 	.phy_id			= ATH8035_PHY_ID,
-	.name			= "Atheros 8035 ethernet",
+	.name			= "Qualcomm Atheros AR8035",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
 	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
@@ -721,9 +721,9 @@ static struct phy_driver at803x_driver[] = {
 	.ack_interrupt		= at803x_ack_interrupt,
 	.config_intr		= at803x_config_intr,
 }, {
-	/* ATHEROS 8030 */
+	/* Qualcomm Atheros AR8030 */
 	.phy_id			= ATH8030_PHY_ID,
-	.name			= "Atheros 8030 ethernet",
+	.name			= "Qualcomm Atheros AR8030",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
 	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
@@ -736,9 +736,9 @@ static struct phy_driver at803x_driver[] = {
 	.ack_interrupt		= at803x_ack_interrupt,
 	.config_intr		= at803x_config_intr,
 }, {
-	/* ATHEROS 8031/8033 */
+	/* Qualcomm Atheros AR8031/AR8033 */
 	.phy_id			= ATH8031_PHY_ID,
-	.name			= "Atheros 8031/8033 ethernet",
+	.name			= "Qualcomm Atheros AR8031/AR8033",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
 	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
@@ -754,7 +754,7 @@ static struct phy_driver at803x_driver[] = {
 }, {
 	/* ATHEROS AR9331 */
 	PHY_ID_MATCH_EXACT(ATH9331_PHY_ID),
-	.name			= "Atheros AR9331 built-in PHY",
+	.name			= "Qualcomm Atheros AR9331 built-in PHY",
 	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
 	.suspend		= at803x_suspend,
-- 
2.20.1

[PATCH v2 6/6] net: phy: at803x: remove config_init for AR9331

[Michael Walle]

According to its datasheet, the internal PHY doesn't have debug
registers nor MMDs. Since config_init() only configures delays and
clocks and so on in these registers it won't be needed on this PHY.
Remove it.

Signed-off-by: Michael Walle <michael@walle.cc>
---
 drivers/net/phy/at803x.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 4434d501cd4f..aee62610bade 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -755,8 +755,6 @@ static struct phy_driver at803x_driver[] = {
 	/* ATHEROS AR9331 */
 	PHY_ID_MATCH_EXACT(ATH9331_PHY_ID),
 	.name			= "Qualcomm Atheros AR9331 built-in PHY",
-	.probe			= at803x_probe,
-	.config_init		= at803x_config_init,
 	.suspend		= at803x_suspend,
 	.resume			= at803x_resume,
 	/* PHY_BASIC_FEATURES */
-- 
2.20.1

Re: [PATCH v2 1/6] net: phy: at803x: fix Kconfig description

[Andrew Lunn]

On Wed, Nov 06, 2019 at 11:36:12PM +0100, Michael Walle wrote:
> The name of the PHY is actually AR803x not AT803x. Additionally, add the
> name of the vendor and mention the AR8031 support.
> 
> Signed-off-by: Michael Walle <michael@walle.cc>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH v2 2/6] dt-bindings: net: phy: Add support for AT803X

[Andrew Lunn]

On Wed, Nov 06, 2019 at 11:36:13PM +0100, Michael Walle wrote:
> Document the Atheros AR803x PHY bindings.
> 
> Signed-off-by: Michael Walle <michael@walle.cc>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
> Reviewed-by: Rob Herring <robh@kernel.org>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH v2 4/6] net: phy: at803x: mention AR8033 as same as AR8031

[Andrew Lunn]

On Wed, Nov 06, 2019 at 11:36:15PM +0100, Michael Walle wrote:
> The AR8033 is the AR8031 without PTP support. All other registers are
> the same. Unfortunately, they share the same PHY ID. Therefore, we
> cannot distinguish between the one with PTP support and the one without.

Not nice. I suppose there might be a PTP register you can read to
determine this, but that is not very helpful.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH v2 5/6] net: phy: at803x: fix the PHY names

[Andrew Lunn]

On Wed, Nov 06, 2019 at 11:36:16PM +0100, Michael Walle wrote:
> Fix at least the displayed strings. The actual name of the chip is
> AR803x.
> 
> Signed-off-by: Michael Walle <michael@walle.cc>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH v2 6/6] net: phy: at803x: remove config_init for AR9331

[Andrew Lunn]

On Wed, Nov 06, 2019 at 11:36:17PM +0100, Michael Walle wrote:
> According to its datasheet, the internal PHY doesn't have debug
> registers nor MMDs. Since config_init() only configures delays and
> clocks and so on in these registers it won't be needed on this PHY.
> Remove it.
> 
> Signed-off-by: Michael Walle <michael@walle.cc>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH v2 0/6] net: phy: at803x device tree binding

[David Miller]

From: Michael Walle <michael@walle.cc>
Date: Wed,  6 Nov 2019 23:36:11 +0100

> Adds a device tree binding to configure the clock and the RGMII voltage.
 ...

Series applied, thank you.

Re: [PATCH v2 4/6] net: phy: at803x: mention AR8033 as same as AR8031

[Michael Walle]

Am 7. November 2019 03:04:36 MEZ schrieb Andrew Lunn <andrew@lunn.ch>:
>On Wed, Nov 06, 2019 at 11:36:15PM +0100, Michael Walle wrote:
>> The AR8033 is the AR8031 without PTP support. All other registers are
>> the same. Unfortunately, they share the same PHY ID. Therefore, we
>> cannot distinguish between the one with PTP support and the one
>without.
>
>Not nice. I suppose there might be a PTP register you can read to
>determine this, but that is not very helpful.

I tried that actually.. There is a PTP enable bit. It's default is 1 (according to the AR8031 datasheet). Now guess what it's value is on the AR8033.. its also 1. Not enough.. I also tried to enable the realtime counter. well that worked too.

And yes. I've double checked the package marking. It definitely was an AR8033. So either I was just lucky, or maybe.. the AR8033 is just a relabled AR8031 ;) 

-michael

Re: [PATCH v2 4/6] net: phy: at803x: mention AR8033 as same as AR8031

[Andrew Lunn]

Hi Michael

> I tried that actually.. There is a PTP enable bit. It's default is 1
> (according to the AR8031 datasheet). Now guess what it's value is on
> the AR8033.. its also 1. Not enough.. I also tried to enable the
> realtime counter. well that worked too.

> And yes. I've double checked the package marking. It definitely was
> an AR8033. So either I was just lucky, or maybe.. the AR8033 is just
> a relabled AR8031 ;)

O.K, thanks for trying. We really only need to solve this mystery if
anybody actually tries to make use of PTP.

	Andrew

Re: [PATCH v2 4/6] net: phy: at803x: mention AR8033 as same as AR8031

[Michael Walle]

Hi Andrew,


Am 2019-11-07 13:55, schrieb Andrew Lunn:
>> I tried that actually.. There is a PTP enable bit. It's default is 1
>> (according to the AR8031 datasheet). Now guess what it's value is on
>> the AR8033.. its also 1. Not enough.. I also tried to enable the
>> realtime counter. well that worked too.
> 
>> And yes. I've double checked the package marking. It definitely was
>> an AR8033. So either I was just lucky, or maybe.. the AR8033 is just
>> a relabled AR8031 ;)
> 
> O.K, thanks for trying. We really only need to solve this mystery if
> anybody actually tries to make use of PTP.

That might be the next thing on my list; but depends if there is an 
usable interrupt for the PHY on my board..

-michael