[Intel-gfx] [V5 0/9] Add support for mipi dsi cmd mode

[Intel-gfx] [V5 0/9] Add support for mipi dsi cmd mode

[Vandita Kulkarni]

This series contains basic cmd mode enablemnet patches.

Vandita Kulkarni (9):
  drm/i915/dsi: Configure transcoder operation for command mode.
  drm/i915/dsi: Add vblank calculation for command mode
  drm/i915/dsi: Add cmd mode flags in display mode private flags
  drm/i915/dsi: Add check for periodic command mode
  drm/i915/dsi: Use private flags to indicate TE in cmd mode
  drm/i915/dsi: Configure TE interrupt for cmd mode
  drm/i915/dsi: Add TE handler for dsi cmd mode.
  drm/i915/dsi: Initiate fame request in cmd mode
  drm/i915/dsi: Clear the DSI IIR

 drivers/gpu/drm/i915/display/icl_dsi.c        | 171 ++++++++++++++++--
 drivers/gpu/drm/i915/display/intel_display.c  |  12 ++
 .../drm/i915/display/intel_display_types.h    |  10 +
 drivers/gpu/drm/i915/display/intel_dsi.h      |   3 +
 drivers/gpu/drm/i915/i915_irq.c               | 124 ++++++++++++-
 5 files changed, 301 insertions(+), 19 deletions(-)

-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] [V5 1/9] drm/i915/dsi: Configure transcoder operation for command mode.

[Vandita Kulkarni]

Configure the transcoder to operate in TE GATE command mode
and  take TE events from GPIO.
Also disable the periodic command mode, that GOP would have
programmed.

v2: Disable util pin (Jani)

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
 drivers/gpu/drm/i915/display/icl_dsi.c | 52 ++++++++++++++++++++++++++
 1 file changed, 52 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 8435bc5a7a74..ca37beca3e41 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -724,6 +724,18 @@ gen11_dsi_configure_transcoder(struct intel_encoder *encoder,
 				tmp |= VIDEO_MODE_SYNC_PULSE;
 				break;
 			}
+		} else {
+			/*
+			 * FIXME: Retrieve this info from VBT.
+			 * As per the spec when dsi transcoder is operating
+			 * in TE GATE mode, TE comes from GPIO
+			 * which is UTIL PIN for DSI 0.
+			 * Also this GPIO would not be used for other
+			 * purposes is an assumption.
+			 */
+			tmp &= ~OP_MODE_MASK;
+			tmp |= CMD_MODE_TE_GATE;
+			tmp |= TE_SOURCE_GPIO;
 		}
 
 		I915_WRITE(DSI_TRANS_FUNC_CONF(dsi_trans), tmp);
@@ -991,6 +1003,32 @@ static void gen11_dsi_setup_timeouts(struct intel_encoder *encoder,
 	}
 }
 
+static void gen11_dsi_config_util_pin(struct intel_encoder *encoder,
+				      bool enable)
+{
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+	u32 tmp;
+
+	/*
+	 * used as TE i/p for DSI0,
+	 * for dual link/DSI1 TE is from slave DSI1
+	 * through GPIO.
+	 */
+	if (is_vid_mode(intel_dsi) || (intel_dsi->ports & BIT(PORT_B)))
+		return;
+
+	tmp = I915_READ(UTIL_PIN_CTL);
+
+	if (enable) {
+		tmp |= UTIL_PIN_DIRECTION_INPUT;
+		tmp |= UTIL_PIN_ENABLE;
+	} else {
+		tmp &= ~UTIL_PIN_ENABLE;
+	}
+	I915_WRITE(UTIL_PIN_CTL, tmp);
+}
+
 static void
 gen11_dsi_enable_port_and_phy(struct intel_encoder *encoder,
 			      const struct intel_crtc_state *crtc_state)
@@ -1012,6 +1050,9 @@ gen11_dsi_enable_port_and_phy(struct intel_encoder *encoder,
 	/* setup D-PHY timings */
 	gen11_dsi_setup_dphy_timings(encoder, crtc_state);
 
+	/* Since transcoder is configured to take events from GPIO */
+	gen11_dsi_config_util_pin(encoder, true);
+
 	/* step 4h: setup DSI protocol timeouts */
 	gen11_dsi_setup_timeouts(encoder, crtc_state);
 
@@ -1144,6 +1185,15 @@ static void gen11_dsi_deconfigure_trancoder(struct intel_encoder *encoder)
 	enum transcoder dsi_trans;
 	u32 tmp;
 
+	/* disable periodic update mode */
+	if (is_cmd_mode(intel_dsi)) {
+		for_each_dsi_port(port, intel_dsi->ports) {
+			tmp = I915_READ(DSI_CMD_FRMCTL(port));
+			tmp &= ~DSI_PERIODIC_FRAME_UPDATE_ENABLE;
+			I915_WRITE(DSI_CMD_FRMCTL(port), tmp);
+		}
+	}
+
 	/* put dsi link in ULPS */
 	for_each_dsi_port(port, intel_dsi->ports) {
 		dsi_trans = dsi_port_to_transcoder(port);
@@ -1247,6 +1297,8 @@ static void gen11_dsi_disable(struct intel_encoder *encoder,
 	/* step3: disable port */
 	gen11_dsi_disable_port(encoder);
 
+	gen11_dsi_config_util_pin(encoder, false);
+
 	/* step4: disable IO power */
 	gen11_dsi_disable_io_power(encoder);
 }
-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] [V5 2/9] drm/i915/dsi: Add vblank calculation for command mode

[Vandita Kulkarni]

Transcoder timing calculation differ for command mode.

v2: Use is_vid_mode, and use same I915_WRITE (Jani)
v3: Adjust the calculations to reflect dsc compression ratio

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
 drivers/gpu/drm/i915/display/icl_dsi.c | 52 +++++++++++++++++---------
 1 file changed, 35 insertions(+), 17 deletions(-)

diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index ca37beca3e41..66dc8be672b8 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -808,9 +808,11 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
 	enum transcoder dsi_trans;
 	/* horizontal timings */
 	u16 htotal, hactive, hsync_start, hsync_end, hsync_size;
+	u16 cal_htotal, cal_vtotal;
 	u16 hback_porch;
 	/* vertical timings */
 	u16 vtotal, vactive, vsync_start, vsync_end, vsync_shift;
+	int bpp, line_time_us, byte_clk_period_ns;
 	int mul = 1, div = 1;
 
 	/*
@@ -827,14 +829,27 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
 	}
 
 	hactive = adjusted_mode->crtc_hdisplay;
-	htotal = DIV_ROUND_UP(adjusted_mode->crtc_htotal * mul, div);
+	vactive = adjusted_mode->crtc_vdisplay;
+	if (is_cmd_mode(intel_dsi)) {
+		bpp = mipi_dsi_pixel_format_to_bpp(intel_dsi->pixel_format);
+		byte_clk_period_ns = 8 * 1000000 / intel_dsi->pclk;
+		cal_htotal = hactive + 160;
+		line_time_us = (cal_htotal * (bpp / 8) * byte_clk_period_ns) / (1000 * intel_dsi->lane_count);
+		cal_vtotal = vactive + DIV_ROUND_UP(460, line_time_us);
+	}
+
+	if (is_vid_mode(intel_dsi))
+		cal_htotal = adjusted_mode->crtc_htotal;
+	htotal = DIV_ROUND_UP(cal_htotal * mul, div);
 	hsync_start = DIV_ROUND_UP(adjusted_mode->crtc_hsync_start * mul, div);
 	hsync_end = DIV_ROUND_UP(adjusted_mode->crtc_hsync_end * mul, div);
 	hsync_size  = hsync_end - hsync_start;
 	hback_porch = (adjusted_mode->crtc_htotal -
 		       adjusted_mode->crtc_hsync_end);
-	vactive = adjusted_mode->crtc_vdisplay;
-	vtotal = adjusted_mode->crtc_vtotal;
+
+	if (is_vid_mode(intel_dsi))
+		cal_vtotal = adjusted_mode->crtc_vtotal;
+	vtotal = cal_vtotal;
 	vsync_start = adjusted_mode->crtc_vsync_start;
 	vsync_end = adjusted_mode->crtc_vsync_end;
 	vsync_shift = hsync_start - htotal / 2;
@@ -862,7 +877,7 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
 	}
 
 	/* TRANS_HSYNC register to be programmed only for video mode */
-	if (intel_dsi->operation_mode == INTEL_DSI_VIDEO_MODE) {
+	if (is_vid_mode(intel_dsi)) {
 		if (intel_dsi->video_mode_format ==
 		    VIDEO_MODE_NON_BURST_WITH_SYNC_PULSE) {
 			/* BSPEC: hsync size should be atleast 16 pixels */
@@ -885,13 +900,12 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
 		}
 	}
 
-	/* program TRANS_VTOTAL register */
 	for_each_dsi_port(port, intel_dsi->ports) {
 		dsi_trans = dsi_port_to_transcoder(port);
 		/*
-		 * FIXME: Programing this by assuming progressive mode, since
-		 * non-interlaced info from VBT is not saved inside
-		 * struct drm_display_mode.
+		 * FIXME: Programing this by assuming progressive mode,
+		 * since non-interlaced info from VBT is not saved
+		 * inside struct drm_display_mode.
 		 * For interlace mode: program required pixel minus 2
 		 */
 		I915_WRITE(VTOTAL(dsi_trans),
@@ -904,22 +918,26 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
 	if (vsync_start < vactive)
 		DRM_ERROR("vsync_start less than vactive\n");
 
-	/* program TRANS_VSYNC register */
-	for_each_dsi_port(port, intel_dsi->ports) {
-		dsi_trans = dsi_port_to_transcoder(port);
-		I915_WRITE(VSYNC(dsi_trans),
-			   (vsync_start - 1) | ((vsync_end - 1) << 16));
+	/* program TRANS_VSYNC register for video mode only */
+	if (is_vid_mode(intel_dsi)) {
+		for_each_dsi_port(port, intel_dsi->ports) {
+			dsi_trans = dsi_port_to_transcoder(port);
+			I915_WRITE(VSYNC(dsi_trans),
+				   (vsync_start - 1) | ((vsync_end - 1) << 16));
+		}
 	}
 
 	/*
-	 * FIXME: It has to be programmed only for interlaced
+	 * FIXME: It has to be programmed only for video modes and interlaced
 	 * modes. Put the check condition here once interlaced
 	 * info available as described above.
 	 * program TRANS_VSYNCSHIFT register
 	 */
-	for_each_dsi_port(port, intel_dsi->ports) {
-		dsi_trans = dsi_port_to_transcoder(port);
-		I915_WRITE(VSYNCSHIFT(dsi_trans), vsync_shift);
+	if (is_vid_mode(intel_dsi)) {
+		for_each_dsi_port(port, intel_dsi->ports) {
+			dsi_trans = dsi_port_to_transcoder(port);
+			I915_WRITE(VSYNCSHIFT(dsi_trans), vsync_shift);
+		}
 	}
 
 	/* program TRANS_VBLANK register, should be same as vtotal programmed */
-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] [V5 3/9] drm/i915/dsi: Add cmd mode flags in display mode private flags

[Vandita Kulkarni]

Adding TE flags and periodic command mode flags
as part of private flags to indicate what TE interrupts
we would be getting instead of vblanks in case of mipi dsi
command mode.

v2: Add TE flag description (Jani)

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
 drivers/gpu/drm/i915/display/intel_display_types.h | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index a1a73209d824..735e67ac6e52 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -656,6 +656,16 @@ struct intel_crtc_scaler_state {
 #define I915_MODE_FLAG_GET_SCANLINE_FROM_TIMESTAMP (1<<1)
 /* Flag to use the scanline counter instead of the pixel counter */
 #define I915_MODE_FLAG_USE_SCANLINE_COUNTER (1<<2)
+/*
+ * TE0 or TE1 flag is set if the crtc has a DSI encoder which
+ * is operating in command mode.
+ * Flag to use TE from DSI0 instead of VBI in command mode
+ */
+#define I915_MODE_FLAG_DSI_USE_TE0 (1<<3)
+/* Flag to use TE from DSI1 instead of VBI in command mode */
+#define I915_MODE_FLAG_DSI_USE_TE1 (1<<4)
+/* Flag to indicate mipi dsi periodic command mode where we do not get TE */
+#define I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE (1<<5)
 
 struct intel_pipe_wm {
 	struct intel_wm_level wm[5];
-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] [V5 4/9] drm/i915/dsi: Add check for periodic command mode

[Vandita Kulkarni]

If the GOP has programmed periodic command mode,
we need to disable that which would need a
deconfigure and configure sequence.

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
 drivers/gpu/drm/i915/display/icl_dsi.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 66dc8be672b8..3ad8cedb5211 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -1378,6 +1378,21 @@ static void gen11_dsi_get_timings(struct intel_encoder *encoder,
 	adjusted_mode->crtc_vblank_end = adjusted_mode->crtc_vtotal;
 }
 
+bool gen11_dsi_is_periodic_cmd_mode(struct drm_i915_private *dev_priv,
+				    struct intel_dsi *intel_dsi)
+{
+	u32 val;
+	enum transcoder dsi_trans;
+
+	if (intel_dsi->ports == BIT(PORT_B))
+		dsi_trans = TRANSCODER_DSI_1;
+	else
+		dsi_trans = TRANSCODER_DSI_0;
+
+	val = I915_READ(DSI_TRANS_FUNC_CONF(dsi_trans));
+	return (val & DSI_PERIODIC_FRAME_UPDATE_ENABLE);
+}
+
 static void gen11_dsi_get_config(struct intel_encoder *encoder,
 				 struct intel_crtc_state *pipe_config)
 {
@@ -1398,6 +1413,10 @@ static void gen11_dsi_get_config(struct intel_encoder *encoder,
 	gen11_dsi_get_timings(encoder, pipe_config);
 	pipe_config->output_types |= BIT(INTEL_OUTPUT_DSI);
 	pipe_config->pipe_bpp = bdw_get_pipemisc_bpp(crtc);
+
+	if (gen11_dsi_is_periodic_cmd_mode(dev_priv, intel_dsi))
+		pipe_config->hw.adjusted_mode.private_flags |=
+					I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE;
 }
 
 static int gen11_dsi_dsc_compute_config(struct intel_encoder *encoder,
@@ -1479,6 +1498,10 @@ static int gen11_dsi_compute_config(struct intel_encoder *encoder,
 
 	pipe_config->port_clock = afe_clk(encoder, pipe_config) / 5;
 
+	/* We would not opereate in peridoc command mode */
+	pipe_config->hw.adjusted_mode.private_flags &=
+					~I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE;
+
 	return 0;
 }
 
-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] [V5 5/9] drm/i915/dsi: Use private flags to indicate TE in cmd mode

[Vandita Kulkarni]

On dsi cmd mode we do not receive vblanks instead
we would get TE and these flags indicate TE is expected on
which port.

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
 drivers/gpu/drm/i915/display/icl_dsi.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 3ad8cedb5211..92faaedd6123 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -1502,6 +1502,24 @@ static int gen11_dsi_compute_config(struct intel_encoder *encoder,
 	pipe_config->hw.adjusted_mode.private_flags &=
 					~I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE;
 
+	/*
+	 * In case of TE GATE cmd mode, we
+	 * receive TE from the slave if
+	 * dual link is enabled
+	 */
+	if (is_cmd_mode(intel_dsi)) {
+		if (intel_dsi->ports == BIT(PORT_B) | BIT(PORT_A))
+			pipe_config->hw.adjusted_mode.private_flags |=
+						I915_MODE_FLAG_DSI_USE_TE1 |
+						I915_MODE_FLAG_DSI_USE_TE0;
+		else if (intel_dsi->ports == BIT(PORT_B))
+			pipe_config->hw.adjusted_mode.private_flags |=
+						I915_MODE_FLAG_DSI_USE_TE1;
+		else
+			pipe_config->hw.adjusted_mode.private_flags |=
+						I915_MODE_FLAG_DSI_USE_TE0;
+	}
+
 	return 0;
 }
 
-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] [V5 6/9] drm/i915/dsi: Configure TE interrupt for cmd mode

[Vandita Kulkarni]

We need to configure TE interrupt in two places.
Port interrupt and DSI interrupt mask registers.

v2: Hide the private flags check inside configure_te (Jani)

v3: Fix the position of masking de_port_masked for DSI_TE.

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
 drivers/gpu/drm/i915/i915_irq.c | 55 +++++++++++++++++++++++++++++++--
 1 file changed, 53 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index afc6aad9bf8c..3f6159708def 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -41,6 +41,7 @@
 #include "display/intel_hotplug.h"
 #include "display/intel_lpe_audio.h"
 #include "display/intel_psr.h"
+#include "display/intel_dsi.h"
 
 #include "gt/intel_gt.h"
 #include "gt/intel_gt_irq.h"
@@ -2581,12 +2582,46 @@ int ilk_enable_vblank(struct drm_crtc *crtc)
 	return 0;
 }
 
+static bool gen11_dsi_configure_te(struct drm_i915_private *dev_priv,
+				   struct drm_display_mode *mode, bool enable)
+{
+	enum port port;
+	u32 tmp;
+
+	if (!(mode->private_flags &
+	    (I915_MODE_FLAG_DSI_USE_TE1 | I915_MODE_FLAG_DSI_USE_TE0)))
+		return false;
+
+	if (mode->private_flags & I915_MODE_FLAG_DSI_USE_TE1)
+		port = PORT_B;
+	else
+		port = PORT_A;
+
+	tmp =  I915_READ(DSI_INTR_MASK_REG(port));
+	if (enable)
+		tmp &= ~DSI_TE_EVENT;
+	else
+		tmp |= DSI_TE_EVENT;
+
+	I915_WRITE(DSI_INTR_MASK_REG(port), tmp);
+	return true;
+}
+
 int bdw_enable_vblank(struct drm_crtc *crtc)
 {
 	struct drm_i915_private *dev_priv = to_i915(crtc->dev);
-	enum pipe pipe = to_intel_crtc(crtc)->pipe;
+	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+	enum pipe pipe = intel_crtc->pipe;
+	struct drm_vblank_crtc *vblank;
+	struct drm_display_mode *mode;
 	unsigned long irqflags;
 
+	vblank = &crtc->dev->vblank[drm_crtc_index(crtc)];
+	mode = &vblank->hwmode;
+
+	if (gen11_dsi_configure_te(dev_priv, mode, true))
+		return 0;
+
 	spin_lock_irqsave(&dev_priv->irq_lock, irqflags);
 	bdw_enable_pipe_irq(dev_priv, pipe, GEN8_PIPE_VBLANK);
 	spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags);
@@ -2652,9 +2687,18 @@ void ilk_disable_vblank(struct drm_crtc *crtc)
 void bdw_disable_vblank(struct drm_crtc *crtc)
 {
 	struct drm_i915_private *dev_priv = to_i915(crtc->dev);
-	enum pipe pipe = to_intel_crtc(crtc)->pipe;
+	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+	enum pipe pipe = intel_crtc->pipe;
+	struct drm_vblank_crtc *vblank;
+	struct drm_display_mode *mode;
 	unsigned long irqflags;
 
+	vblank = &crtc->dev->vblank[drm_crtc_index(crtc)];
+	mode = &vblank->hwmode;
+
+	if (gen11_dsi_configure_te(dev_priv, mode, false))
+		return;
+
 	spin_lock_irqsave(&dev_priv->irq_lock, irqflags);
 	bdw_disable_pipe_irq(dev_priv, pipe, GEN8_PIPE_VBLANK);
 	spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags);
@@ -3347,6 +3391,13 @@ static void gen8_de_irq_postinstall(struct drm_i915_private *dev_priv)
 	if (IS_CNL_WITH_PORT_F(dev_priv) || INTEL_GEN(dev_priv) >= 11)
 		de_port_masked |= CNL_AUX_CHANNEL_F;
 
+	if (INTEL_GEN(dev_priv) >= 11) {
+		enum port port;
+
+		if (intel_bios_is_dsi_present(dev_priv, &port))
+			de_port_masked |= DSI0_TE | DSI1_TE;
+	}
+
 	de_pipe_enables = de_pipe_masked | GEN8_PIPE_VBLANK |
 					   GEN8_PIPE_FIFO_UNDERRUN;
 
-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] [V5 7/9] drm/i915/dsi: Add TE handler for dsi cmd mode.

[Vandita Kulkarni]

In case of dual link, we get the TE on slave.
So clear the TE on slave DSI IIR.

v2: Pass only relevant masked bits to the handler (Jani)

v3: Fix the check for cmd mode in TE handler function.

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
 drivers/gpu/drm/i915/i915_irq.c | 64 +++++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 3f6159708def..028d4d66da8a 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -2230,6 +2230,62 @@ gen8_de_misc_irq_handler(struct drm_i915_private *dev_priv, u32 iir)
 		DRM_ERROR("Unexpected DE Misc interrupt\n");
 }
 
+void gen11_dsi_te_interrupt_handler(struct drm_i915_private *dev_priv,
+				    u32 te_trigger)
+{
+	enum pipe pipe = INVALID_PIPE;
+	enum transcoder dsi_trans;
+	enum port port;
+	u32 val, tmp;
+
+	/*
+	 * Incase of dual link, TE comes from DSI_1
+	 * this is to check if dual link is enabled
+	 */
+	val = I915_READ(TRANS_DDI_FUNC_CTL2(TRANSCODER_DSI_0));
+	val &= PORT_SYNC_MODE_ENABLE;
+
+	/*
+	 * if dual link is enabled, then read DSI_0
+	 * transcoder registers
+	 */
+	port = ((te_trigger & DSI1_TE && val) || (te_trigger & DSI0_TE)) ?
+						  PORT_A : PORT_B;
+	dsi_trans = (port == PORT_A) ? TRANSCODER_DSI_0 : TRANSCODER_DSI_1;
+
+	/* Check if DSI configured in command mode */
+	val = I915_READ(DSI_TRANS_FUNC_CONF(dsi_trans));
+	val = val & OP_MODE_MASK;
+
+	if ((val != CMD_MODE_NO_GATE) && (val != CMD_MODE_TE_GATE)) {
+		DRM_ERROR("DSI trancoder not configured in command mode\n");
+		return;
+	}
+
+	/* Get PIPE for handling VBLANK event */
+	val = I915_READ(TRANS_DDI_FUNC_CTL(dsi_trans));
+	switch (val & TRANS_DDI_EDP_INPUT_MASK) {
+	case TRANS_DDI_EDP_INPUT_A_ON:
+		pipe = PIPE_A;
+		break;
+	case TRANS_DDI_EDP_INPUT_B_ONOFF:
+		pipe = PIPE_B;
+		break;
+	case TRANS_DDI_EDP_INPUT_C_ONOFF:
+		pipe = PIPE_C;
+		break;
+	default:
+		DRM_ERROR("Invalid PIPE\n");
+	}
+
+	/* clear TE in dsi IIR */
+	port = (te_trigger & DSI1_TE) ? PORT_B : PORT_A;
+	tmp = I915_READ(DSI_INTR_IDENT_REG(port));
+	I915_WRITE(DSI_INTR_IDENT_REG(port), tmp);
+
+	drm_handle_vblank(&dev_priv->drm, pipe);
+}
+
 static irqreturn_t
 gen8_de_irq_handler(struct drm_i915_private *dev_priv, u32 master_ctl)
 {
@@ -2294,6 +2350,14 @@ gen8_de_irq_handler(struct drm_i915_private *dev_priv, u32 master_ctl)
 				found = true;
 			}
 
+			if (INTEL_GEN(dev_priv) >= 11) {
+				tmp_mask = iir & (DSI0_TE | DSI1_TE);
+				if (tmp_mask) {
+					gen11_dsi_te_interrupt_handler(dev_priv, tmp_mask);
+					found = true;
+				}
+			}
+
 			if (!found)
 				DRM_ERROR("Unexpected DE Port interrupt\n");
 		}
-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] [V5 8/9] drm/i915/dsi: Initiate fame request in cmd mode

[Vandita Kulkarni]

In TE Gate mode, on every flip we need to set the
frame update request bit. After this  bit is set
transcoder hardware will automatically send the
frame data to the panel when it receives the TE event.

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
 drivers/gpu/drm/i915/display/icl_dsi.c       | 26 ++++++++++++++++++++
 drivers/gpu/drm/i915/display/intel_display.c | 12 +++++++++
 drivers/gpu/drm/i915/display/intel_dsi.h     |  3 +++
 3 files changed, 41 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 92faaedd6123..20d136203de7 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -199,6 +199,32 @@ static int dsi_send_pkt_payld(struct intel_dsi_host *host,
 	return 0;
 }
 
+void gen11_dsi_frame_update(struct intel_crtc_state *crtc_state)
+{
+	struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc);
+	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
+	u32 tmp, private_flags;
+	enum port port;
+
+	private_flags = crtc_state->hw.adjusted_mode.private_flags;
+
+	/*
+	 * case 1 also covers dual link
+	 * In case of dual link, frame update should be set on
+	 * DSI_0
+	 */
+	if (private_flags & I915_MODE_FLAG_DSI_USE_TE0)
+		port = PORT_A;
+	else if (private_flags & I915_MODE_FLAG_DSI_USE_TE1)
+		port = PORT_B;
+	else
+		return;
+
+	tmp = I915_READ(DSI_CMD_FRMCTL(port));
+	tmp |= DSI_FRAME_UPDATE_REQUEST;
+	I915_WRITE(DSI_CMD_FRMCTL(port), tmp);
+}
+
 static void dsi_program_swing_and_deemphasis(struct intel_encoder *encoder)
 {
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index 59c375879186..76cfd39300ee 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -15411,6 +15411,18 @@ static void intel_atomic_commit_tail(struct intel_atomic_state *state)
 			intel_color_load_luts(new_crtc_state);
 	}
 
+	/*
+	 * Incase of mipi dsi command mode, we need to set frame update
+	 * for every commit
+	 */
+	for_each_new_intel_crtc_in_state(state, crtc, new_crtc_state, i) {
+		if ((INTEL_GEN(dev_priv) >= 11) &&
+		    (intel_crtc_has_type(new_crtc_state, INTEL_OUTPUT_DSI))) {
+			if (new_crtc_state->hw.active)
+				gen11_dsi_frame_update(new_crtc_state);
+		}
+	}
+
 	/*
 	 * Now that the vblank has passed, we can go ahead and program the
 	 * optimal watermarks on platforms that need two-step watermark
diff --git a/drivers/gpu/drm/i915/display/intel_dsi.h b/drivers/gpu/drm/i915/display/intel_dsi.h
index 7481a5aa3084..6e64d3d2cd0a 100644
--- a/drivers/gpu/drm/i915/display/intel_dsi.h
+++ b/drivers/gpu/drm/i915/display/intel_dsi.h
@@ -202,6 +202,9 @@ u32 bxt_dsi_get_pclk(struct intel_encoder *encoder,
 		     struct intel_crtc_state *config);
 void bxt_dsi_reset_clocks(struct intel_encoder *encoder, enum port port);
 
+/* icl_dsi.c */
+void gen11_dsi_frame_update(struct intel_crtc_state *crtc_state);
+
 /* intel_dsi_vbt.c */
 bool intel_dsi_vbt_init(struct intel_dsi *intel_dsi, u16 panel_id);
 void intel_dsi_vbt_gpio_init(struct intel_dsi *intel_dsi, bool panel_is_on);
-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] [V5 9/9] drm/i915/dsi: Clear the DSI IIR

[Vandita Kulkarni]

Clear the DSI IIR as part of interrupt configuration.

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
 drivers/gpu/drm/i915/i915_irq.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 028d4d66da8a..fabba515c274 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -2668,6 +2668,11 @@ static bool gen11_dsi_configure_te(struct drm_i915_private *dev_priv,
 		tmp |= DSI_TE_EVENT;
 
 	I915_WRITE(DSI_INTR_MASK_REG(port), tmp);
+
+	/* FIXME: right place to clear this */
+	tmp = I915_READ(DSI_INTR_IDENT_REG(port));
+	I915_WRITE(DSI_INTR_IDENT_REG(port), tmp);
+
 	return true;
 }
 
-- 
2.21.0.5.gaeb582a

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[Intel-gfx] ✗ Fi.CI.BUILD: failure for Add support for mipi dsi cmd mode (rev4)

[Patchwork]

== Series Details ==

Series: Add support for mipi dsi cmd mode (rev4)
URL   : https://patchwork.freedesktop.org/series/69290/
State : failure

== Summary ==

CALL    scripts/checksyscalls.sh
  CALL    scripts/atomic/check-atomics.sh
  DESCEND  objtool
  CHK     include/generated/compile.h
  CC [M]  drivers/gpu/drm/i915/display/icl_dsi.o
drivers/gpu/drm/i915/display/icl_dsi.c: In function ‘gen11_dsi_compute_config’:
drivers/gpu/drm/i915/display/icl_dsi.c:1537:24: error: suggest parentheses around comparison in operand of ‘|’ [-Werror=parentheses]
   if (intel_dsi->ports == BIT(PORT_B) | BIT(PORT_A))
cc1: all warnings being treated as errors
scripts/Makefile.build:265: recipe for target 'drivers/gpu/drm/i915/display/icl_dsi.o' failed
make[4]: *** [drivers/gpu/drm/i915/display/icl_dsi.o] Error 1
scripts/Makefile.build:503: recipe for target 'drivers/gpu/drm/i915' failed
make[3]: *** [drivers/gpu/drm/i915] Error 2
scripts/Makefile.build:503: recipe for target 'drivers/gpu/drm' failed
make[2]: *** [drivers/gpu/drm] Error 2
scripts/Makefile.build:503: recipe for target 'drivers/gpu' failed
make[1]: *** [drivers/gpu] Error 2
Makefile:1693: recipe for target 'drivers' failed
make: *** [drivers] Error 2

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx