All of lore.kernel.org
 help / color / mirror / Atom feed
From: Icenowy Zheng <icenowy@aosc.io>
To: Rob Herring <robh+dt@kernel.org>,
	Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
	Thierry Reding <thierry.reding@gmail.com>,
	Sam Ravnborg <sam@ravnborg.org>, David Airlie <airlied@linux.ie>,
	Daniel Vetter <daniel@ffwll.ch>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, dri-devel@lists.freedesktop.org,
	linux-sunxi@googlegroups.com, Icenowy Zheng <icenowy@aosc.io>
Subject: [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab
Date: Fri, 10 Jan 2020 23:52:25 +0800	[thread overview]
Message-ID: <20200110155225.1051749-6-icenowy@aosc.io> (raw)
In-Reply-To: <20200110155225.1051749-1-icenowy@aosc.io>

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.

Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.

Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.

Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.

Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.

Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.

Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.

Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.

This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, and
the front camera currently lacks a driver and a facility to share the
bus with the rear one.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 461 ++++++++++++++++++
 2 files changed, 462 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index cf4f78617c3f..6dad63881cd3 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
new file mode 100644
index 000000000000..1dfa3668636e
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
@@ -0,0 +1,461 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "PineTab";
+	compatible = "pine64,pinetab", "allwinner,sun50i-a64";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &rtl8723cs;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
+		power-supply = <&vdd_bl>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	i2c-csi {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
+		scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */
+		i2c-gpio,delay-us = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Rear camera */
+		ov5640: camera@3c {
+			compatible = "ovti,ov5640";
+			reg = <0x3c>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&csi_mclk_pin>;
+			clocks = <&ccu CLK_CSI_MCLK>;
+			clock-names = "xclk";
+
+			AVDD-supply = <&reg_dldo3>;
+			DOVDD-supply = <&reg_aldo1>;
+			DVDD-supply = <&reg_eldo3>;
+			reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */
+			powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+
+			port {
+				ov5640_ep: endpoint {
+					remote-endpoint = <&csi_ep>;
+					bus-width = <8>;
+					hsync-active = <1>; /* Active high */
+					vsync-active = <0>; /* Active low */
+					data-active = <1>;  /* Active high */
+					pclk-sample = <1>;  /* Rising */
+				};
+			};
+		};
+	};
+
+	speaker_amp: audio-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		sound-name-prefix = "Speaker Amp";
+	};
+
+	vdd_bl: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "bl-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+		enable-active-high;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&codec {
+	status = "okay";
+};
+
+&codec_analog {
+	hpvcc-supply = <&reg_eldo1>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&csi {
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi_ep: endpoint {
+			remote-endpoint = <&ov5640_ep>;
+			bus-width = <8>;
+			hsync-active = <1>; /* Active high */
+			vsync-active = <0>; /* Active low */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
+&dai {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	vcc-dsi-supply = <&reg_dldo1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "feixin,k101-im2ba02";
+		reg = <0>;
+		avdd-supply = <&reg_dc1sw>;
+		dvdd-supply = <&reg_dc1sw>;
+		cvdd-supply = <&reg_ldo_io1>;
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+		backlight = <&backlight>;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	touchscreen@5d {
+		compatible = "goodix,gt9271";
+		reg = <0x5d>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
+		irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+		reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+		AVDD28-supply = <&reg_ldo_io1>;
+	};
+};
+
+&i2c0_pins {
+	bias-pull-up;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+
+	bma223@18 {
+		compatible = "bosch,bma223", "bosch,bma222e";
+		reg = <0x18>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 5 IRQ_TYPE_LEVEL_HIGH>; /* PH5 */
+		mount-matrix = "0", "-1", "0",
+			       "-1", "0", "0",
+			       "0", "0", "-1";
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_aldo3>;
+	status = "okay";
+
+	button-200 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button-400 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mixer1 {
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_dldo4>;
+	vqmmc-supply = <&reg_eldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723cs: wifi@1 {
+		reg = <1>;
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pwm {
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en;
+	};
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&reg_aldo1 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "dovdd-csi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-lcd";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi-sensor";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "avdd-csi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcca-1v8";
+};
+
+&reg_eldo3 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dvdd-1v8-csi";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_ldo_io0 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-usb";
+	status = "okay";
+};
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-enable-ramp-delay = <3500000>;
+	regulator-name = "vcc-touchscreen";
+	status = "okay";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&sound {
+	status = "okay";
+	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
+	simple-audio-card,widgets = "Microphone", "Internal Microphone Left",
+				    "Microphone", "Internal Microphone Right",
+				    "Headphone", "Headphone Jack",
+				    "Speaker", "Internal Speaker";
+	simple-audio-card,routing =
+			"Left DAC", "AIF1 Slot 0 Left",
+			"Right DAC", "AIF1 Slot 0 Right",
+			"Speaker Amp INL", "LINEOUT",
+			"Speaker Amp INR", "LINEOUT",
+			"Internal Speaker", "Speaker Amp OUTL",
+			"Internal Speaker", "Speaker Amp OUTR",
+			"Headphone Jack", "HP",
+			"AIF1 Slot 0 Left ADC", "Left ADC",
+			"AIF1 Slot 0 Right ADC", "Right ADC",
+			"Internal Microphone Left", "MBIAS",
+			"MIC1", "Internal Microphone Left",
+			"Internal Microphone Right", "HBIAS",
+			"MIC2", "Internal Microphone Right";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_ldo_io0>;
+	status = "okay";
+};
-- 
2.23.0


WARNING: multiple messages have this Message-ID
From: Icenowy Zheng <icenowy@aosc.io>
To: Rob Herring <robh+dt@kernel.org>,
	Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
	Thierry Reding <thierry.reding@gmail.com>,
	Sam Ravnborg <sam@ravnborg.org>, David Airlie <airlied@linux.ie>,
	Daniel Vetter <daniel@ffwll.ch>
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	dri-devel@lists.freedesktop.org, linux-sunxi@googlegroups.com,
	linux-arm-kernel@lists.infradead.org,
	Icenowy Zheng <icenowy@aosc.io>
Subject: [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab
Date: Fri, 10 Jan 2020 23:52:25 +0800	[thread overview]
Message-ID: <20200110155225.1051749-6-icenowy@aosc.io> (raw)
In-Reply-To: <20200110155225.1051749-1-icenowy@aosc.io>

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.

Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.

Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.

Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.

Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.

Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.

Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.

Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.

This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, and
the front camera currently lacks a driver and a facility to share the
bus with the rear one.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 461 ++++++++++++++++++
 2 files changed, 462 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index cf4f78617c3f..6dad63881cd3 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
new file mode 100644
index 000000000000..1dfa3668636e
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
@@ -0,0 +1,461 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "PineTab";
+	compatible = "pine64,pinetab", "allwinner,sun50i-a64";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &rtl8723cs;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
+		power-supply = <&vdd_bl>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	i2c-csi {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
+		scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */
+		i2c-gpio,delay-us = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Rear camera */
+		ov5640: camera@3c {
+			compatible = "ovti,ov5640";
+			reg = <0x3c>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&csi_mclk_pin>;
+			clocks = <&ccu CLK_CSI_MCLK>;
+			clock-names = "xclk";
+
+			AVDD-supply = <&reg_dldo3>;
+			DOVDD-supply = <&reg_aldo1>;
+			DVDD-supply = <&reg_eldo3>;
+			reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */
+			powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+
+			port {
+				ov5640_ep: endpoint {
+					remote-endpoint = <&csi_ep>;
+					bus-width = <8>;
+					hsync-active = <1>; /* Active high */
+					vsync-active = <0>; /* Active low */
+					data-active = <1>;  /* Active high */
+					pclk-sample = <1>;  /* Rising */
+				};
+			};
+		};
+	};
+
+	speaker_amp: audio-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		sound-name-prefix = "Speaker Amp";
+	};
+
+	vdd_bl: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "bl-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+		enable-active-high;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&codec {
+	status = "okay";
+};
+
+&codec_analog {
+	hpvcc-supply = <&reg_eldo1>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&csi {
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi_ep: endpoint {
+			remote-endpoint = <&ov5640_ep>;
+			bus-width = <8>;
+			hsync-active = <1>; /* Active high */
+			vsync-active = <0>; /* Active low */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
+&dai {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	vcc-dsi-supply = <&reg_dldo1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "feixin,k101-im2ba02";
+		reg = <0>;
+		avdd-supply = <&reg_dc1sw>;
+		dvdd-supply = <&reg_dc1sw>;
+		cvdd-supply = <&reg_ldo_io1>;
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+		backlight = <&backlight>;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	touchscreen@5d {
+		compatible = "goodix,gt9271";
+		reg = <0x5d>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
+		irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+		reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+		AVDD28-supply = <&reg_ldo_io1>;
+	};
+};
+
+&i2c0_pins {
+	bias-pull-up;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+
+	bma223@18 {
+		compatible = "bosch,bma223", "bosch,bma222e";
+		reg = <0x18>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 5 IRQ_TYPE_LEVEL_HIGH>; /* PH5 */
+		mount-matrix = "0", "-1", "0",
+			       "-1", "0", "0",
+			       "0", "0", "-1";
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_aldo3>;
+	status = "okay";
+
+	button-200 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button-400 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mixer1 {
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_dldo4>;
+	vqmmc-supply = <&reg_eldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723cs: wifi@1 {
+		reg = <1>;
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pwm {
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en;
+	};
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&reg_aldo1 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "dovdd-csi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-lcd";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi-sensor";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "avdd-csi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcca-1v8";
+};
+
+&reg_eldo3 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dvdd-1v8-csi";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_ldo_io0 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-usb";
+	status = "okay";
+};
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-enable-ramp-delay = <3500000>;
+	regulator-name = "vcc-touchscreen";
+	status = "okay";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&sound {
+	status = "okay";
+	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
+	simple-audio-card,widgets = "Microphone", "Internal Microphone Left",
+				    "Microphone", "Internal Microphone Right",
+				    "Headphone", "Headphone Jack",
+				    "Speaker", "Internal Speaker";
+	simple-audio-card,routing =
+			"Left DAC", "AIF1 Slot 0 Left",
+			"Right DAC", "AIF1 Slot 0 Right",
+			"Speaker Amp INL", "LINEOUT",
+			"Speaker Amp INR", "LINEOUT",
+			"Internal Speaker", "Speaker Amp OUTL",
+			"Internal Speaker", "Speaker Amp OUTR",
+			"Headphone Jack", "HP",
+			"AIF1 Slot 0 Left ADC", "Left ADC",
+			"AIF1 Slot 0 Right ADC", "Right ADC",
+			"Internal Microphone Left", "MBIAS",
+			"MIC1", "Internal Microphone Left",
+			"Internal Microphone Right", "HBIAS",
+			"MIC2", "Internal Microphone Right";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_ldo_io0>;
+	status = "okay";
+};
-- 
2.23.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

WARNING: multiple messages have this Message-ID
From: Icenowy Zheng <icenowy@aosc.io>
To: Rob Herring <robh+dt@kernel.org>,
	Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
	Thierry Reding <thierry.reding@gmail.com>,
	Sam Ravnborg <sam@ravnborg.org>, David Airlie <airlied@linux.ie>,
	Daniel Vetter <daniel@ffwll.ch>
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	dri-devel@lists.freedesktop.org, linux-sunxi@googlegroups.com,
	linux-arm-kernel@lists.infradead.org,
	Icenowy Zheng <icenowy@aosc.io>
Subject: [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab
Date: Fri, 10 Jan 2020 23:52:25 +0800	[thread overview]
Message-ID: <20200110155225.1051749-6-icenowy@aosc.io> (raw)
In-Reply-To: <20200110155225.1051749-1-icenowy@aosc.io>

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.

Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.

Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.

Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.

Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.

Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.

Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.

Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.

This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, and
the front camera currently lacks a driver and a facility to share the
bus with the rear one.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 461 ++++++++++++++++++
 2 files changed, 462 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index cf4f78617c3f..6dad63881cd3 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
new file mode 100644
index 000000000000..1dfa3668636e
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
@@ -0,0 +1,461 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "PineTab";
+	compatible = "pine64,pinetab", "allwinner,sun50i-a64";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &rtl8723cs;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
+		power-supply = <&vdd_bl>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	i2c-csi {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
+		scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */
+		i2c-gpio,delay-us = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Rear camera */
+		ov5640: camera@3c {
+			compatible = "ovti,ov5640";
+			reg = <0x3c>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&csi_mclk_pin>;
+			clocks = <&ccu CLK_CSI_MCLK>;
+			clock-names = "xclk";
+
+			AVDD-supply = <&reg_dldo3>;
+			DOVDD-supply = <&reg_aldo1>;
+			DVDD-supply = <&reg_eldo3>;
+			reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */
+			powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+
+			port {
+				ov5640_ep: endpoint {
+					remote-endpoint = <&csi_ep>;
+					bus-width = <8>;
+					hsync-active = <1>; /* Active high */
+					vsync-active = <0>; /* Active low */
+					data-active = <1>;  /* Active high */
+					pclk-sample = <1>;  /* Rising */
+				};
+			};
+		};
+	};
+
+	speaker_amp: audio-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		sound-name-prefix = "Speaker Amp";
+	};
+
+	vdd_bl: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "bl-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+		enable-active-high;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&codec {
+	status = "okay";
+};
+
+&codec_analog {
+	hpvcc-supply = <&reg_eldo1>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&csi {
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi_ep: endpoint {
+			remote-endpoint = <&ov5640_ep>;
+			bus-width = <8>;
+			hsync-active = <1>; /* Active high */
+			vsync-active = <0>; /* Active low */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
+&dai {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	vcc-dsi-supply = <&reg_dldo1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "feixin,k101-im2ba02";
+		reg = <0>;
+		avdd-supply = <&reg_dc1sw>;
+		dvdd-supply = <&reg_dc1sw>;
+		cvdd-supply = <&reg_ldo_io1>;
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+		backlight = <&backlight>;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	touchscreen@5d {
+		compatible = "goodix,gt9271";
+		reg = <0x5d>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
+		irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+		reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+		AVDD28-supply = <&reg_ldo_io1>;
+	};
+};
+
+&i2c0_pins {
+	bias-pull-up;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+
+	bma223@18 {
+		compatible = "bosch,bma223", "bosch,bma222e";
+		reg = <0x18>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 5 IRQ_TYPE_LEVEL_HIGH>; /* PH5 */
+		mount-matrix = "0", "-1", "0",
+			       "-1", "0", "0",
+			       "0", "0", "-1";
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_aldo3>;
+	status = "okay";
+
+	button-200 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button-400 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mixer1 {
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_dldo4>;
+	vqmmc-supply = <&reg_eldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723cs: wifi@1 {
+		reg = <1>;
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pwm {
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en;
+	};
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&reg_aldo1 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "dovdd-csi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-lcd";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi-sensor";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "avdd-csi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcca-1v8";
+};
+
+&reg_eldo3 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dvdd-1v8-csi";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_ldo_io0 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-usb";
+	status = "okay";
+};
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-enable-ramp-delay = <3500000>;
+	regulator-name = "vcc-touchscreen";
+	status = "okay";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&sound {
+	status = "okay";
+	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
+	simple-audio-card,widgets = "Microphone", "Internal Microphone Left",
+				    "Microphone", "Internal Microphone Right",
+				    "Headphone", "Headphone Jack",
+				    "Speaker", "Internal Speaker";
+	simple-audio-card,routing =
+			"Left DAC", "AIF1 Slot 0 Left",
+			"Right DAC", "AIF1 Slot 0 Right",
+			"Speaker Amp INL", "LINEOUT",
+			"Speaker Amp INR", "LINEOUT",
+			"Internal Speaker", "Speaker Amp OUTL",
+			"Internal Speaker", "Speaker Amp OUTR",
+			"Headphone Jack", "HP",
+			"AIF1 Slot 0 Left ADC", "Left ADC",
+			"AIF1 Slot 0 Right ADC", "Right ADC",
+			"Internal Microphone Left", "MBIAS",
+			"MIC1", "Internal Microphone Left",
+			"Internal Microphone Right", "HBIAS",
+			"MIC2", "Internal Microphone Right";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_ldo_io0>;
+	status = "okay";
+};
-- 
2.23.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

  parent reply	other threads:[~2020-01-10 15:54 UTC|newest]

Thread overview: 42+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-01-10 15:52 [PATCH 0/5] Add support for Pine64 PineTab Icenowy Zheng
2020-01-10 15:52 ` Icenowy Zheng
2020-01-10 15:52 ` Icenowy Zheng
2020-01-10 15:52 ` [PATCH 1/5] dt-bindings: vendor-prefix: add Shenzhen Feixin Photoelectics Co., Ltd Icenowy Zheng
2020-01-10 15:52   ` Icenowy Zheng
2020-01-10 15:52   ` Icenowy Zheng
2020-01-10 17:07   ` Sam Ravnborg
2020-01-10 17:07     ` Sam Ravnborg
2020-01-10 17:07     ` Sam Ravnborg
2020-01-15 15:22   ` Rob Herring
2020-01-15 15:22     ` Rob Herring
2020-01-15 15:22     ` Rob Herring
2020-01-10 15:52 ` [PATCH 2/5] dt-bindings: panel: add Feixin K101 IM2BA02 MIPI-DSI panel Icenowy Zheng
2020-01-10 15:52   ` Icenowy Zheng
2020-01-10 15:52   ` Icenowy Zheng
2020-01-10 17:12   ` Sam Ravnborg
2020-01-10 17:12     ` Sam Ravnborg
2020-01-10 17:12     ` Sam Ravnborg
2020-01-10 15:52 ` [PATCH 3/5] drm/panel: Add Feixin K101 IM2BA02 panel Icenowy Zheng
2020-01-10 15:52   ` Icenowy Zheng
2020-01-10 15:52   ` Icenowy Zheng
2020-01-10 17:46   ` Sam Ravnborg
2020-01-10 17:46     ` Sam Ravnborg
2020-01-10 17:46     ` Sam Ravnborg
2020-01-10 15:52 ` [PATCH 4/5] dt-bindings: arm: sunxi: add binding for PineTab tablet Icenowy Zheng
2020-01-10 15:52   ` Icenowy Zheng
2020-01-10 15:52   ` Icenowy Zheng
2020-01-15 15:24   ` Rob Herring
2020-01-15 15:24     ` Rob Herring
2020-01-15 15:24     ` Rob Herring
2020-01-10 15:52 ` Icenowy Zheng [this message]
2020-01-10 15:52   ` [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab Icenowy Zheng
2020-01-10 15:52   ` Icenowy Zheng
2020-01-10 17:23   ` Maxime Ripard
2020-01-10 17:23     ` Maxime Ripard
2020-01-10 17:23     ` Maxime Ripard
2020-01-10 18:12   ` Sam Ravnborg
2020-01-10 18:12     ` Sam Ravnborg
2020-01-10 18:12     ` Sam Ravnborg
2020-01-10 18:51   ` [linux-sunxi] " Vasily Khoruzhick
2020-01-10 18:51     ` Vasily Khoruzhick
2020-01-10 18:51     ` Vasily Khoruzhick

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200110155225.1051749-6-icenowy@aosc.io \
    --to=icenowy@aosc.io \
    --cc=airlied@linux.ie \
    --cc=daniel@ffwll.ch \
    --cc=devicetree@vger.kernel.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-sunxi@googlegroups.com \
    --cc=mripard@kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=sam@ravnborg.org \
    --cc=thierry.reding@gmail.com \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.