[PATCH v7 10/11] vl: replace deprecated qbus_reset_all registration

[Damien Hedde <damien.hedde@greensocs.com>]

Replace deprecated qbus_reset_all by resettable_cold_reset_fn for
the sysbus reset registration.

Apart for the raspi machines, this does not impact the behavior
because:
+ at this point resettable just calls the old reset methods of devices
  and buses in the same order as qdev/qbus.
+ resettable handlers registered with qemu_register_reset are
  serialized; there is no interleaving.
+ eventual explicit calls to legacy reset API (device_reset or
  qdev/qbus_reset) inside this reset handler will not be masked out
  by resettable mechanism; they do not go through resettable api.

For the raspi machines, during the sysbus reset the sd-card is not
reset twice anymore but only once. This is a consequence of switching
both sysbus reset and changing parent to resettable; it detects the
second reset is not needed. This has no impact on the state after
reset; the sd-card reset method only reset local state and query
information from the block backend.

Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---

The raspi reset change can be observed by using the following command
(reset will occurs, then do Ctrl-C to end qemu; no firmware is
given here).
qemu-system-aarch64 -M raspi3 \
    -trace resettable_phase_hold_exec \
    -trace qdev_update_parent_bus \
    -trace resettable_change_parent \
    -trace qdev_reset -trace qbus_reset

Before the patch, the qdev/qbus_reset traces show when reset method are
called. After the patch, the resettable_phase_hold_exec show when reset
method are called.

The traced reset order of the raspi3 is listed below. I've added empty
lines and the tree structure.

 +->bcm2835-peripherals reset
 |
 |       +->sd-card reset
 |   +->sd-bus reset
 +->bcm2835_gpio reset
 |      -> dev_update_parent_bus (move the sd-card on the sdhci-bus)
 |      -> resettable_change_parent
 |
 +->bcm2835-dma reset
 |
 |   +->bcm2835-sdhost-bus reset
 +->bcm2835-sdhost reset
 |
 |       +->sd-card (reset ONLY BEFORE BEFORE THE PATCH)
 |   +->sdhci-bus reset
 +->generic-sdhci reset
 |
 +->bcm2835-rng reset
 +->bcm2835-property reset
 +->bcm2835-fb reset
 +->bcm2835-mbox reset
 +->bcm2835-aux reset
 +->pl011 reset
 +->bcm2835-ic reset
 +->bcm2836-control reset
System reset

In both case, the sd-card is reset (being on bcm2835_gpio/sd-bus) then moved
to generic-sdhci/sdhci-bus by the bcm2835_gpio reset method.

Before the patch, it is then reset again being part of generic-sdhci/sdhci-bus.
After the patch, it considered again for reset but its reset method is not
called because it is already flagged as reset.
---
 vl.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/vl.c b/vl.c
index 751401214c..e5a537d4f9 100644
--- a/vl.c
+++ b/vl.c
@@ -4362,7 +4362,15 @@ int main(int argc, char **argv, char **envp)
 
     /* TODO: once all bus devices are qdevified, this should be done
      * when bus is created by qdev.c */
-    qemu_register_reset(qbus_reset_all_fn, sysbus_get_default());
+    /*
+     * TODO: If we had a main 'reset container' that the whole system
+     * lived in, we could reset that using the multi-phase reset
+     * APIs. For the moment, we just reset the sysbus, which will cause
+     * all devices hanging off it (and all their child buses, recursively)
+     * to be reset. Note that this will *not* reset any Device objects
+     * which are not attached to some part of the qbus tree!
+     */
+    qemu_register_reset(resettable_cold_reset_fn, sysbus_get_default());
     qemu_run_machine_init_done_notifiers();
 
     if (rom_check_and_register_reset() != 0) {
-- 
2.24.1