From mboxrd@z Thu Jan 1 00:00:00 1970 From: Pali =?utf-8?B?Um9ow6Fy?= Date: Sun, 26 Apr 2020 01:54:59 +0200 Subject: U-Boot i2c bus num 1 is broken on Nokia N900 (Was: Re: U-Boot is broken on real N900 HW) In-Reply-To: <20200425121132.vnlurfxti6y433pq@pali> References: <20200331223518.10936-1-pali@kernel.org> <20200331224254.nzaotf5abj6w7n65@pali> <3c7dda52-10b3-e8c3-a382-785c80f124e7@wizzup.org> <20200402184231.jzhy36qfbi4drnli@pali> <20200425104217.pzp5zkhhft5a2he5@pali> <20200425115045.w45tb62cnwtq5umk@pali> <20200425121132.vnlurfxti6y433pq@pali> Message-ID: <20200425235459.bcoskmnux45x4iqs@pali> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Adding Hannes and Heiko to the loop, please look at this problem. On Saturday 25 April 2020 14:11:32 Pali Roh?r wrote: > On Saturday 25 April 2020 07:00:58 Adam Ford wrote: > > On Sat, Apr 25, 2020 at 6:50 AM Pali Roh?r wrote: > > > > > > On Saturday 25 April 2020 06:36:58 Adam Ford wrote: > > > > On Sat, Apr 25, 2020 at 5:42 AM Pali Roh?r wrote: > > > > > > > > > > On Thursday 02 April 2020 20:42:31 Pali Roh?r wrote: > > > > > > On Wednesday 01 April 2020 12:32:29 Merlijn Wajer wrote: > > > > > > > Hi, > > > > > > > > > > > > > > On 01/04/2020 00:42, Pali Roh?r wrote: > > > > > > > > On Wednesday 01 April 2020 00:35:07 Pali Roh?r wrote: > > > > > > > >> This patch series contain fixes for Nokia RX-51 board (aka N900). > > > > > > > >> After these changes it is possible to run U-Boot in qemu emulator again. > > > > > > > >> And U-Boot can boot kernel image from RAM, eMMC or OneNAND memory without > > > > > > > >> problem. > > > > > > > > > > > > > > > > But on real Nokia N900 device is U-Boot crashing in reboot loop. > > > > > > > > > > > > > > > > I do not have serial console for Nokia N900 to debug this issue, but > > > > > > > > seems that it is related to OMAP I2C and OMAP HS MMC code. Problem is > > > > > > > > that there is no crash and even no error in qemu emulator so I cannot > > > > > > > > debug this issue. > > > > > > > > > > > > > > > > First problem is around /* reset lp5523 led */ code in rx51.c. On real > > > > > > > > N900 device it generates repeating messages: > > > > > > > > > > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > > > > > > > > > > When I commented that few lines all these messages disappeared. So > > > > > > > > problem is with OMAP I2C. ... > > > > > > > > I remember that somebody had serial jig for Nokia N900, could somebody > > > > > > > > look at this reboot loop problem? > > > > > > > > > > > > > > > > And any idea how should be OMAP I2C configured in U-Boot to correctly > > > > > > > > work? > > > > > > > > > > > > > > > > Maybe I will try to find some time to git bisect which change broke > > > > > > > > U-Boot on real N900 hardware. > > > > > > > > > > > > > > Took latest u-boot master, applied patches and this is the result on > > > > > > > serial (first part is NOLO booting, I think that can be ignored) [1]. > > > > > > > > > > > > ... > > > > > > > > > > > > > U-Boot 2020.04-rc4-00033-g7dbafe0634-dirty (Apr 01 2020 - 12:15:47 +0200) > > > > > > > > > > > > > > OMAP3530-HS ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 MHz > > > > > > > Nokia RX-51 + LPDDR/OneNAND > > > > > > > I2C: ready > > > > > > > DRAM: 256 MiB > > > > > > > NAND: 0 Bytes > > > > > > > > > > > > Looks like that something with NAND is broken. > > > > > > > > > > > > > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > > > > > > > In: vga > > > > > > > Out: vga > > > > > > > Err: vga > > > > > > > Timed out in wait_for_event: status=0100 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > Timed out in wait_for_event: status=0000 > > > > > > > Check if pads/pull-ups of bus are properly configured > > > > > > > i2c_read (addr phase): pads on bus probably not configured (status=0x10) > > > > > > > i2c_write: timed out writig last byte! > > > > > > > > > > > > These i2c errors are caused by > > > > > > > > > > > > /* reset lp5523 led */ > > > > > > i2c_set_bus_num(1); > > > > > > state = 0xff; > > > > > > i2c_write(0x32, 0x3d, 1, &state, 1); > > > > > > i2c_set_bus_num(0); > > > > > > > > > > > > Is there anything which needs to be done to initialize i2c bus 1? > > > > > > Because this code is working fine on older U-Boot version. > > > > > > > > > > Above code worked fine for U-Boot 2013.04, but in git version from > > > > > January 2015 it prints above error messages. > > > > > > > > > > On on internet forums I see these error messages also from other OMAP3 > > > > > board, e.g. beagle board. > > > > > > > > > > Has somebody some working OMAP3 board? And can test if it works with > > > > > recent version of U-Boot? I guess that above i2c problem would happen > > > > > also on other OMAP3 boards. > > > > > > > > There was a conversion a while ago to dm_i2c, and I converted my board > > > > to support using the device tree during the SPL phase, and whenever I > > > > am aware any driver has driver model (DM) support, I try to convert my > > > > board. > > > > > > > > I have a DM3730 and the last check I did was 2020.04-rc1, and it was working > > > > > > Ok, so it either OMAP3430 specific problem or N900 board specific > > > problem. N900 does not use driver model. > > > > i have an OMAP3530 which is basically a 3430, and it works too. I am > > guessing the issue is unique to the N900 or the fact that it's > > high-security. Neither of my boards are HS parts. They are both GP. > > N900 is HS device, but I guess that should be caused by GP vs HS > difference. Working i2c bus 0 and non-working i2c bus 1 could not be > caused by GP vs HS difference. Also I guess that omap hs mmc would be > same on GP and HS boards. ... > > > Before calling i2c_write(0x32, ...) I tried to call i2c_probe(0x32) and > > > it returned error. > > > > > > If I tried to call "i2c dev 1" in U-Boot console, I got tons of errors > > > and basically U-Boot stopped responding. > > > > > > So by above observation it looks like I2C bus num 1 does not work, but > > > I2C bus num 0 works fine. > > > > > > Do I need to call i2c_probe(...) before calling i2c_write(...)? > > > > > > And is something special needed for initializing omap i2c bus num 1? > > > Because from my above observation it looks like that something is > > > missing for bus 1 which in older u-boot version was not needed. Now I was able to find commit which is causing above i2c problems: "Check if pads/pull-ups of bus are properly configured" It is d5243359e1afc957acd373dbbde1cf6c70ee5485: OMAP24xx I2C: Add support for set-speed Adds support for set-speed on the OMAP24xx I2C Adapter. Changes to omap24_i2c_write(...) for polling ARDY Bit from IRQ-Status. Otherwise on a subsequent call the transfer of last byte from the predecessor is aborted and therefore lost. For exmaple when i2c_write(...) is followed by a i2c_setspeed(...) (which has to deactivate and activate master for changing psc,...). Minor cosmetical changes. Signed-off-by: Hannes Petermaier Cc: Heiko Schocher U-Boot version prior this command does not report those i2c errors. Hannes, any idea how your patch could broke omap i2c i2c bus num 1 on Nokia N900?