[PATCH v3 0/4] Convert adi,adv7511.txt DT bindings to yaml

[PATCH v3 0/4] Convert adi,adv7511.txt DT bindings to yaml

[Ricardo Cañuelo]

Hi,

This series convert the adi,adv7511.txt DT bindings to json-schema. As a
result of the conversion some dts files needed to be updated.

The changes to the dts files are of three types:

  - Reordering of the I2C slave addresses list of the ADV75xx node. The
    addresses in the 'reg' property and the matching names in
    'reg-names' for an I2C slave don't need to be in any particular
    order, but the DT schema defines these properties as a cell array
    and a string array respectively, which are ordered, so the
    definitions in the dts files must match the order in the binding.

  - Filling the minimum binding requirements. Most of the time this
    means creating a 'ports' node in the boards that don't define
    them. Note, however, that the purpose of this is simply to make the
    definition compliant with the binding. I didn't define any endpoints
    for the ports.

  - Removing unneeded properties.

About the binding conversion:

  - The original binding covered five different devices: ADV7511,
    ADV7511W, ADV7513, ADV7533 and ADV7535. They all share a common set
    of properties but ADV7533 and ADV7535 have enough differences from
    the rest to warrant their own binding file. In v1 I modelled all the
    properties constraints for all five devices in a single file but it
    turned out a bit too complex. Splitting the binding into one for
    ADV7511/11W/13 and another for ADV7533/35 makes them much easier to
    read and maintain.

Patches 1/4 to 3/4 contain the dts changes. Patch 4/4 contains the
binding conversion.

NOTE: the bindings have been tested with:

  make dt_binding_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
  make dt_binding_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7533.yaml>
  make dtbs_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
  make dtbs_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7533.yaml>

for <arch> = arm and arm64. dts changes haven't been tested in hardware.

Some existing DTs are expected to fail after this conversion.

Changes in v3:

  - Removed from the patch series (already in mainline):
    - arm64: dts: renesas: make hdmi encoder nodes compliant with DT bindings
    - ARM: dts: renesas: make hdmi encoder nodes compliant with DT bindings
    - ARM: dts: iwg20d-q7-dbcm-ca: remove unneeded properties in hdmi@39

  - Additional DTs fixes:
    - boot/dts/stm32mp15xx-dhcor-avenger96.dtsi.

  - [Laurent] adi,adv7511.yaml and adi,adv7533.yaml.
    - Documentation fixes and typos.
    - Removed unnecessary allOf's.
    - adi,embedded-sync data type changed to boolean.
    - Power supplies defined as required.
    - Examples updated.

Ricardo Cañuelo (4):
  ARM: dts: zynq: add port definitions to hdmi-tx@39
  arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT
    binding
  ARM: dts: stm32: make hdmi-transmitter node compliant with DT bindings
  dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml

 .../bindings/display/bridge/adi,adv7511.txt   | 143 -----------
 .../bindings/display/bridge/adi,adv7511.yaml  | 231 ++++++++++++++++++
 .../bindings/display/bridge/adi,adv7533.yaml  | 175 +++++++++++++
 .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi |   6 +-
 arch/arm/boot/dts/zynq-zc702.dts              |  10 +
 arch/arm/boot/dts/zynq-zc706.dts              |  10 +
 .../boot/dts/hisilicon/hi3660-hikey960.dts    |  11 +
 .../arm64/boot/dts/hisilicon/hi6220-hikey.dts |   2 +-
 8 files changed, 440 insertions(+), 148 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
 create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
 create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml

-- 
2.18.0

[PATCH v3 0/4] Convert adi,adv7511.txt DT bindings to yaml

[Ricardo Cañuelo]

Hi,

This series convert the adi,adv7511.txt DT bindings to json-schema. As a
result of the conversion some dts files needed to be updated.

The changes to the dts files are of three types:

  - Reordering of the I2C slave addresses list of the ADV75xx node. The
    addresses in the 'reg' property and the matching names in
    'reg-names' for an I2C slave don't need to be in any particular
    order, but the DT schema defines these properties as a cell array
    and a string array respectively, which are ordered, so the
    definitions in the dts files must match the order in the binding.

  - Filling the minimum binding requirements. Most of the time this
    means creating a 'ports' node in the boards that don't define
    them. Note, however, that the purpose of this is simply to make the
    definition compliant with the binding. I didn't define any endpoints
    for the ports.

  - Removing unneeded properties.

About the binding conversion:

  - The original binding covered five different devices: ADV7511,
    ADV7511W, ADV7513, ADV7533 and ADV7535. They all share a common set
    of properties but ADV7533 and ADV7535 have enough differences from
    the rest to warrant their own binding file. In v1 I modelled all the
    properties constraints for all five devices in a single file but it
    turned out a bit too complex. Splitting the binding into one for
    ADV7511/11W/13 and another for ADV7533/35 makes them much easier to
    read and maintain.

Patches 1/4 to 3/4 contain the dts changes. Patch 4/4 contains the
binding conversion.

NOTE: the bindings have been tested with:

  make dt_binding_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
  make dt_binding_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7533.yaml>
  make dtbs_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
  make dtbs_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7533.yaml>

for <arch> = arm and arm64. dts changes haven't been tested in hardware.

Some existing DTs are expected to fail after this conversion.

Changes in v3:

  - Removed from the patch series (already in mainline):
    - arm64: dts: renesas: make hdmi encoder nodes compliant with DT bindings
    - ARM: dts: renesas: make hdmi encoder nodes compliant with DT bindings
    - ARM: dts: iwg20d-q7-dbcm-ca: remove unneeded properties in hdmi@39

  - Additional DTs fixes:
    - boot/dts/stm32mp15xx-dhcor-avenger96.dtsi.

  - [Laurent] adi,adv7511.yaml and adi,adv7533.yaml.
    - Documentation fixes and typos.
    - Removed unnecessary allOf's.
    - adi,embedded-sync data type changed to boolean.
    - Power supplies defined as required.
    - Examples updated.

Ricardo Cañuelo (4):
  ARM: dts: zynq: add port definitions to hdmi-tx@39
  arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT
    binding
  ARM: dts: stm32: make hdmi-transmitter node compliant with DT bindings
  dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml

 .../bindings/display/bridge/adi,adv7511.txt   | 143 -----------
 .../bindings/display/bridge/adi,adv7511.yaml  | 231 ++++++++++++++++++
 .../bindings/display/bridge/adi,adv7533.yaml  | 175 +++++++++++++
 .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi |   6 +-
 arch/arm/boot/dts/zynq-zc702.dts              |  10 +
 arch/arm/boot/dts/zynq-zc706.dts              |  10 +
 .../boot/dts/hisilicon/hi3660-hikey960.dts    |  11 +
 .../arm64/boot/dts/hisilicon/hi6220-hikey.dts |   2 +-
 8 files changed, 440 insertions(+), 148 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
 create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
 create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml

-- 
2.18.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 1/4] ARM: dts: zynq: add port definitions to hdmi-tx@39

[Ricardo Cañuelo]

Define a 'ports' node for 'adv7511: hdmi-tx@39' to make it compliant with
the adi,adv7511 DT binding.

This fills the minimum requirements to meet the binding requirements,
remote endpoints are not defined.

Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
---
 arch/arm/boot/dts/zynq-zc702.dts | 10 ++++++++++
 arch/arm/boot/dts/zynq-zc706.dts | 10 ++++++++++
 2 files changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/zynq-zc702.dts b/arch/arm/boot/dts/zynq-zc702.dts
index 27cd6cb52f1b..79fd236edded 100644
--- a/arch/arm/boot/dts/zynq-zc702.dts
+++ b/arch/arm/boot/dts/zynq-zc702.dts
@@ -135,6 +135,16 @@
 				adi,input-clock = "1x";
 				adi,input-style = <3>;
 				adi,input-justification = "right";
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					port@0 {
+						reg = <0>;
+					};
+					port@1 {
+						reg = <1>;
+					};
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/zynq-zc706.dts b/arch/arm/boot/dts/zynq-zc706.dts
index 77943c16d33f..99fa51ba6e93 100644
--- a/arch/arm/boot/dts/zynq-zc706.dts
+++ b/arch/arm/boot/dts/zynq-zc706.dts
@@ -93,6 +93,16 @@
 				adi,input-clock = "1x";
 				adi,input-style = <3>;
 				adi,input-justification = "evenly";
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					port@0 {
+						reg = <0>;
+					};
+					port@1 {
+						reg = <1>;
+					};
+				};
 			};
 		};
 
-- 
2.18.0

[PATCH v3 1/4] ARM: dts: zynq: add port definitions to hdmi-tx@39

[Ricardo Cañuelo]

Define a 'ports' node for 'adv7511: hdmi-tx@39' to make it compliant with
the adi,adv7511 DT binding.

This fills the minimum requirements to meet the binding requirements,
remote endpoints are not defined.

Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
---
 arch/arm/boot/dts/zynq-zc702.dts | 10 ++++++++++
 arch/arm/boot/dts/zynq-zc706.dts | 10 ++++++++++
 2 files changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/zynq-zc702.dts b/arch/arm/boot/dts/zynq-zc702.dts
index 27cd6cb52f1b..79fd236edded 100644
--- a/arch/arm/boot/dts/zynq-zc702.dts
+++ b/arch/arm/boot/dts/zynq-zc702.dts
@@ -135,6 +135,16 @@
 				adi,input-clock = "1x";
 				adi,input-style = <3>;
 				adi,input-justification = "right";
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					port@0 {
+						reg = <0>;
+					};
+					port@1 {
+						reg = <1>;
+					};
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/zynq-zc706.dts b/arch/arm/boot/dts/zynq-zc706.dts
index 77943c16d33f..99fa51ba6e93 100644
--- a/arch/arm/boot/dts/zynq-zc706.dts
+++ b/arch/arm/boot/dts/zynq-zc706.dts
@@ -93,6 +93,16 @@
 				adi,input-clock = "1x";
 				adi,input-style = <3>;
 				adi,input-justification = "evenly";
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					port@0 {
+						reg = <0>;
+					};
+					port@1 {
+						reg = <1>;
+					};
+				};
 			};
 		};
 
-- 
2.18.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 2/4] arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT binding

[Ricardo Cañuelo]

hi3660-hikey960.dts:
  Define a 'ports' node for 'adv7533: adv7533@39' and the
  'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
  binding.

  This fills the requirements to meet the binding requirements,
  remote endpoints are not defined.

hi6220-hikey.dts:
  Change property name s/pd-gpio/pd-gpios, gpio properties should be
  plural. This is just a cosmetic change.

Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
 arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 11 +++++++++++
 arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts    |  2 +-
 2 files changed, 12 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index e035cf195b19..8c4bfbaf3a80 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -530,6 +530,17 @@
 		status = "ok";
 		compatible = "adi,adv7533";
 		reg = <0x39>;
+		adi,dsi-lanes = <4>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+			};
+			port@1 {
+				reg = <1>;
+			};
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index c14205cd6bf5..3e47150c05ec 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -516,7 +516,7 @@
 		reg = <0x39>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <1 2>;
-		pd-gpio = <&gpio0 4 0>;
+		pd-gpios = <&gpio0 4 0>;
 		adi,dsi-lanes = <4>;
 		#sound-dai-cells = <0>;
 
-- 
2.18.0

[PATCH v3 2/4] arm64: dts: hisilicon: hikey: fixes to comply with adi, adv7533 DT binding

[Ricardo Cañuelo]

hi3660-hikey960.dts:
  Define a 'ports' node for 'adv7533: adv7533@39' and the
  'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
  binding.

  This fills the requirements to meet the binding requirements,
  remote endpoints are not defined.

hi6220-hikey.dts:
  Change property name s/pd-gpio/pd-gpios, gpio properties should be
  plural. This is just a cosmetic change.

Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
 arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 11 +++++++++++
 arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts    |  2 +-
 2 files changed, 12 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index e035cf195b19..8c4bfbaf3a80 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -530,6 +530,17 @@
 		status = "ok";
 		compatible = "adi,adv7533";
 		reg = <0x39>;
+		adi,dsi-lanes = <4>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+			};
+			port@1 {
+				reg = <1>;
+			};
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index c14205cd6bf5..3e47150c05ec 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -516,7 +516,7 @@
 		reg = <0x39>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <1 2>;
-		pd-gpio = <&gpio0 4 0>;
+		pd-gpios = <&gpio0 4 0>;
 		adi,dsi-lanes = <4>;
 		#sound-dai-cells = <0>;
 
-- 
2.18.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/4] ARM: dts: stm32: make hdmi-transmitter node compliant with DT bindings

[Ricardo Cañuelo]

Reorder the I2C slave addresses of the hdmi-transmitter node and remove
the adi,input-style and adi,input-justification properties to meet the
adi,adv7513 binding requirements.

Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
---
 arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
index 930202742a3f..b67a21a8698a 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
@@ -185,8 +185,8 @@
 &i2c4 {
 	hdmi-transmitter@3d {
 		compatible = "adi,adv7513";
-		reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
-		reg-names = "main", "cec", "edid", "packet";
+		reg = <0x3d>, <0x4d>, <0x2d> , <0x5d>;
+		reg-names = "main", "edid", "cec", "packet";
 		clocks = <&cec_clock>;
 		clock-names = "cec";
 
@@ -204,8 +204,6 @@
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
 
 		ports {
 			#address-cells = <1>;
-- 
2.18.0

[PATCH v3 3/4] ARM: dts: stm32: make hdmi-transmitter node compliant with DT bindings

[Ricardo Cañuelo]

Reorder the I2C slave addresses of the hdmi-transmitter node and remove
the adi,input-style and adi,input-justification properties to meet the
adi,adv7513 binding requirements.

Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
---
 arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
index 930202742a3f..b67a21a8698a 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
@@ -185,8 +185,8 @@
 &i2c4 {
 	hdmi-transmitter@3d {
 		compatible = "adi,adv7513";
-		reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
-		reg-names = "main", "cec", "edid", "packet";
+		reg = <0x3d>, <0x4d>, <0x2d> , <0x5d>;
+		reg-names = "main", "edid", "cec", "packet";
 		clocks = <&cec_clock>;
 		clock-names = "cec";
 
@@ -204,8 +204,6 @@
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
 
 		ports {
 			#address-cells = <1>;
-- 
2.18.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 4/4] dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml

[Ricardo Cañuelo]

Convert the ADV7511/11w/13/33/35 DT bindings to json-schema. The
original binding has been split into two files: adi,adv7511.yaml for
ADV7511/11W/13 and adi,adv7533.yaml for ADV7533/35.

Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
---
 .../bindings/display/bridge/adi,adv7511.txt   | 143 -----------
 .../bindings/display/bridge/adi,adv7511.yaml  | 231 ++++++++++++++++++
 .../bindings/display/bridge/adi,adv7533.yaml  | 175 +++++++++++++
 3 files changed, 406 insertions(+), 143 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
 create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
 create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml

diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
deleted file mode 100644
index 659523f538bf..000000000000
--- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
+++ /dev/null
@@ -1,143 +0,0 @@
-Analog Devices ADV7511(W)/13/33/35 HDMI Encoders
-------------------------------------------------
-
-The ADV7511, ADV7511W, ADV7513, ADV7533 and ADV7535 are HDMI audio and video
-transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space
-conversion, S/PDIF, CEC and HDCP. ADV7533/5 supports the DSI interface for input
-pixels, while the others support RGB interface.
-
-Required properties:
-
-- compatible: Should be one of:
-		"adi,adv7511"
-		"adi,adv7511w"
-		"adi,adv7513"
-		"adi,adv7533"
-		"adi,adv7535"
-
-- reg: I2C slave addresses
-  The ADV7511 internal registers are split into four pages exposed through
-  different I2C addresses, creating four register maps. Each map has it own
-  I2C address and acts as a standard slave device on the I2C bus. The main
-  address is mandatory, others are optional and revert to defaults if not
-  specified.
-
-
-The ADV7511 supports a large number of input data formats that differ by their
-color depth, color format, clock mode, bit justification and random
-arrangement of components on the data bus. The combination of the following
-properties describe the input and map directly to the video input tables of the
-ADV7511 datasheet that document all the supported combinations.
-
-- adi,input-depth: Number of bits per color component at the input (8, 10 or
-  12).
-- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
-  "yuv444".
-- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
-  pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
-  data driven on both edges).
-
-The following input format properties are required except in "rgb 1x" and
-"yuv444 1x" modes, in which case they must not be specified.
-
-- adi,input-style: The input components arrangement variant (1, 2 or 3), as
-  listed in the input format tables in the datasheet.
-- adi,input-justification: The input bit justification ("left", "evenly",
-  "right").
-
-- avdd-supply: A 1.8V supply that powers up the AVDD pin on the chip.
-- dvdd-supply: A 1.8V supply that powers up the DVDD pin on the chip.
-- pvdd-supply: A 1.8V supply that powers up the PVDD pin on the chip.
-- dvdd-3v-supply: A 3.3V supply that powers up the pin called DVDD_3V
-  on the chip.
-- bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is
-  needed only for ADV7511.
-
-The following properties are required for ADV7533 and ADV7535:
-
-- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
-  be one of 1, 2, 3 or 4.
-- a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip.
-- v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip.
-- v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be
-  either 1.2V or 1.8V for ADV7533 but only 1.8V for ADV7535.
-
-Optional properties:
-
-- interrupts: Specifier for the ADV7511 interrupt
-- pd-gpios: Specifier for the GPIO connected to the power down signal
-
-- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
-  (-1200 ps .. 1600 ps). Defaults to no delay.
-- adi,embedded-sync: The input uses synchronization signals embedded in the
-  data stream (similar to BT.656). Defaults to separate H/V synchronization
-  signals.
-- adi,disable-timing-generator: Only for ADV7533 and ADV7535. Disables the
-  internal timing generator. The chip will rely on the sync signals in the
-  DSI data lanes, rather than generate its own timings for HDMI output.
-- clocks: from common clock binding: reference to the CEC clock.
-- clock-names: from common clock binding: must be "cec".
-- reg-names : Names of maps with programmable addresses.
-	It can contain any map needing a non-default address.
-	Possible maps names are : "main", "edid", "cec", "packet"
-
-Required nodes:
-
-The ADV7511 has two video ports. Their connections are modelled using the OF
-graph bindings specified in Documentation/devicetree/bindings/graph.txt.
-
-- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533/5, the
-  remote endpoint phandle should be a reference to a valid mipi_dsi_host device
-  node.
-- Video port 1 for the HDMI output
-- Audio port 2 for the HDMI audio input
-
-
-Example
--------
-
-	adv7511w: hdmi@39 {
-		compatible = "adi,adv7511w";
-		/*
-		 * The EDID page will be accessible on address 0x66 on the I2C
-		 * bus. All other maps continue to use their default addresses.
-		 */
-		reg = <0x39>, <0x66>;
-		reg-names = "main", "edid";
-		interrupt-parent = <&gpio3>;
-		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
-		clocks = <&cec_clock>;
-		clock-names = "cec";
-
-		adi,input-depth = <8>;
-		adi,input-colorspace = "rgb";
-		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7511w_in: endpoint {
-					remote-endpoint = <&dpi_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				adv7511_out: endpoint {
-					remote-endpoint = <&hdmi_connector_in>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-				codec_endpoint: endpoint {
-					remote-endpoint = <&i2s0_cpu_endpoint>;
-				};
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
new file mode 100644
index 000000000000..71b344e812dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
@@ -0,0 +1,231 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/adi,adv7511.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7511/11W/13 HDMI Encoders
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+description: |
+  The ADV7511, ADV7511W and ADV7513 are HDMI audio and video
+  transmitters compatible with HDMI 1.4 and DVI 1.0. They support color
+  space conversion, S/PDIF, CEC and HDCP. The transmitter input is
+  parallel RGB or YUV data.
+
+properties:
+  compatible:
+    enum:
+      - adi,adv7511
+      - adi,adv7511w
+      - adi,adv7513
+
+  reg:
+    description: |
+      I2C slave addresses.
+
+      The ADV7511/11W/13 internal registers are split into four pages
+      exposed through different I2C addresses, creating four register
+      maps. Each map has it own I2C address and acts as a standard slave
+      device on the I2C bus. The main address is mandatory, others are
+      optional and revert to defaults if not specified.
+    minItems: 1
+    maxItems: 4
+
+  reg-names:
+    description:
+      Names of maps with programmable addresses. It can contain any map
+      needing a non-default address.
+    minItems: 1
+    items:
+      - const: main
+      - const: edid
+      - const: cec
+      - const: packet
+
+  clocks:
+    description: Reference to the CEC clock.
+    maxItems: 1
+
+  clock-names:
+    const: cec
+
+  interrupts:
+    maxItems: 1
+
+  pd-gpios:
+    description: GPIO connected to the power down signal.
+    maxItems: 1
+
+  avdd-supply:
+    description: A 1.8V supply that powers up the AVDD pin.
+
+  dvdd-supply:
+    description: A 1.8V supply that powers up the DVDD pin.
+
+  pvdd-supply:
+    description: A 1.8V supply that powers up the PVDD pin.
+
+  dvdd-3v-supply:
+    description: A 3.3V supply that powers up the DVDD_3V pin.
+
+  bgvdd-supply:
+    description: A 1.8V supply that powers up the BGVDD pin.
+
+  adi,input-depth:
+    description: Number of bits per color component at the input.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 8, 10, 12 ]
+
+  adi,input-colorspace:
+    description: Input color space.
+    enum: [ rgb, yuv422, yuv444 ]
+
+  adi,input-clock:
+    description: |
+      Input clock type.
+        "1x": one clock cycle per pixel
+        "2x": two clock cycles per pixel
+        "dd": one clock cycle per pixel, data driven on both edges
+    enum: [ 1x, 2x, dd ]
+
+  adi,clock-delay:
+    description:
+      Video data clock delay relative to the pixel clock, in ps
+      (-1200ps .. 1600 ps).
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
+
+  adi,embedded-sync:
+    description:
+      If defined, the input uses synchronization signals embedded in the
+      data stream (similar to BT.656).
+    type: boolean
+
+  adi,input-style:
+    description:
+      Input components arrangement variant as listed in the input
+      format tables in the datasheet.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 1, 2, 3 ]
+
+  adi,input-justification:
+    description: Input bit justification.
+    enum: [ left, evenly, right ]
+
+  ports:
+    description:
+      The ADV7511(W)/13 has two video ports and one audio port. This node
+      models their connections as documented in
+      Documentation/devicetree/bindings/media/video-interfaces.txt
+      Documentation/devicetree/bindings/graph.txt
+    type: object
+    properties:
+      port@0:
+        description: Video port for the RGB or YUV input.
+        type: object
+
+      port@1:
+        description: Video port for the HDMI output.
+        type: object
+
+      port@2:
+        description: Audio port for the HDMI output.
+        type: object
+
+# adi,input-colorspace and adi,input-clock are required except in
+# "rgb 1x" and "yuv444 1x" modes, in which case they must not be
+# specified.
+if:
+  not:
+    properties:
+      adi,input-colorspace:
+        contains:
+          enum: [ rgb, yuv444 ]
+      adi,input-clock:
+        contains:
+          const: 1x
+
+then:
+  required:
+    - adi,input-style
+    - adi,input-justification
+
+else:
+  properties:
+    adi,input-style: false
+    adi,input-justification: false
+
+
+required:
+  - compatible
+  - reg
+  - ports
+  - adi,input-depth
+  - adi,input-colorspace
+  - adi,input-clock
+  - avdd-supply
+  - dvdd-supply
+  - pvdd-supply
+  - dvdd-3v-supply
+  - bgvdd-supply
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    adv7511w: hdmi@39 {
+        compatible = "adi,adv7511w";
+        /*
+         * The EDID page will be accessible on address 0x66 on the I2C
+         * bus. All other maps continue to use their default addresses.
+         */
+        reg = <0x39>, <0x66>;
+        reg-names = "main", "edid";
+        interrupt-parent = <&gpio3>;
+        interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+        clocks = <&cec_clock>;
+        clock-names = "cec";
+        avdd-supply = <&v1v8>;
+        dvdd-supply = <&v1v8>;
+        pvdd-supply = <&v1v8>;
+        dvdd-3v-supply = <&v3v3>;
+        bgvdd-supply = <&v1v8>;
+
+        adi,input-depth = <8>;
+        adi,input-colorspace = "yuv422";
+        adi,input-clock = "1x";
+
+        adi,input-style = <3>;
+        adi,input-justification = "right";
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                adv7511w_in: endpoint {
+                    remote-endpoint = <&dpi_out>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                adv7511_out: endpoint {
+                    remote-endpoint = <&hdmi_connector_in>;
+                };
+            };
+
+            port@2 {
+                reg = <2>;
+                codec_endpoint: endpoint {
+                    remote-endpoint = <&i2s0_cpu_endpoint>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml b/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
new file mode 100644
index 000000000000..18761f49e5fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/adi,adv7533.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7533/35 HDMI Encoders
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+description: |
+  The ADV7533 and ADV7535 are HDMI audio and video transmitters
+  compatible with HDMI 1.4 and DVI 1.0. They support color space
+  conversion, S/PDIF, CEC and HDCP. The transmitter input is MIPI DSI.
+
+properties:
+  compatible:
+    enum:
+      - adi,adv7533
+      - adi,adv7535
+
+  reg:
+    description: |
+      I2C slave addresses.
+
+      The ADV7533/35 internal registers are split into four pages
+      exposed through different I2C addresses, creating four register
+      maps. Each map has it own I2C address and acts as a standard slave
+      device on the I2C bus. The main address is mandatory, others are
+      optional and revert to defaults if not specified.
+    minItems: 1
+    maxItems: 4
+
+  reg-names:
+    description:
+      Names of maps with programmable addresses. It can contain any map
+      needing a non-default address.
+    minItems: 1
+    items:
+      - const: main
+      - const: edid
+      - const: cec
+      - const: packet
+
+  clocks:
+    description: Reference to the CEC clock.
+    maxItems: 1
+
+  clock-names:
+    const: cec
+
+  interrupts:
+    maxItems: 1
+
+  pd-gpios:
+    description: GPIO connected to the power down signal.
+    maxItems: 1
+
+  avdd-supply:
+    description: A 1.8V supply that powers up the AVDD pin.
+
+  dvdd-supply:
+    description: A 1.8V supply that powers up the DVDD pin.
+
+  pvdd-supply:
+    description: A 1.8V supply that powers up the PVDD pin.
+
+  a2vdd-supply:
+    description: A 1.8V supply that powers up the A2VDD pin.
+
+  v3p3-supply:
+    description: A 3.3V supply that powers up the V3P3 pin.
+
+  v1p2-supply:
+    description:
+      A supply that powers up the V1P2 pin. It can be either 1.2V
+      or 1.8V for ADV7533 but only 1.8V for ADV7535.
+
+  adi,disable-timing-generator:
+    description:
+      Disables the internal timing generator. The chip will rely on the
+      sync signals in the DSI data lanes, rather than generating its own
+      timings for HDMI output.
+    type: boolean
+
+  adi,dsi-lanes:
+    description: Number of DSI data lanes connected to the DSI host.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 1, 2, 3, 4 ]
+
+  ports:
+    description:
+      The ADV7533/35 has two video ports and one audio port. This node
+      models their connections as documented in
+      Documentation/devicetree/bindings/media/video-interfaces.txt
+      Documentation/devicetree/bindings/graph.txt
+    type: object
+    properties:
+      port@0:
+        description:
+          Video port for the DSI input. The remote endpoint phandle
+          should be a reference to a valid mipi_dsi_host_device.
+        type: object
+
+      port@1:
+        description: Video port for the HDMI output.
+        type: object
+
+      port@2:
+        description: Audio port for the HDMI output.
+        type: object
+
+required:
+  - compatible
+  - reg
+  - ports
+  - adi,dsi-lanes
+  - avdd-supply
+  - dvdd-supply
+  - pvdd-supply
+  - a2vdd-supply
+  - v3p3-supply
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    adv7533: hdmi@39 {
+        compatible = "adi,adv7533";
+        /*
+         * The EDID page will be accessible on address 0x66 on the I2C
+         * bus. All other maps continue to use their default addresses.
+         */
+        reg = <0x39>, <0x66>;
+        reg-names = "main", "edid";
+        interrupt-parent = <&gpio3>;
+        interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+        clocks = <&cec_clock>;
+        clock-names = "cec";
+        adi,dsi-lanes = <4>;
+        avdd-supply = <&v1v8>;
+        dvdd-supply = <&v1v8>;
+        pvdd-supply = <&v1v8>;
+        a2vdd-supply = <&v1v8>;
+        v3p3-supply = <&v3v3>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                adv7533_in: endpoint {
+                    remote-endpoint = <&dsi_out>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                adv7533_out: endpoint {
+                    remote-endpoint = <&hdmi_connector_in>;
+                };
+            };
+
+            port@2 {
+                reg = <2>;
+                codec_endpoint: endpoint {
+                    remote-endpoint = <&i2s0_cpu_endpoint>;
+                };
+            };
+        };
+    };
+
+...
-- 
2.18.0

[PATCH v3 4/4] dt-bindings: drm: bridge: adi, adv7511.txt: convert to yaml

[Ricardo Cañuelo]

Convert the ADV7511/11w/13/33/35 DT bindings to json-schema. The
original binding has been split into two files: adi,adv7511.yaml for
ADV7511/11W/13 and adi,adv7533.yaml for ADV7533/35.

Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
---
 .../bindings/display/bridge/adi,adv7511.txt   | 143 -----------
 .../bindings/display/bridge/adi,adv7511.yaml  | 231 ++++++++++++++++++
 .../bindings/display/bridge/adi,adv7533.yaml  | 175 +++++++++++++
 3 files changed, 406 insertions(+), 143 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
 create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
 create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml

diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
deleted file mode 100644
index 659523f538bf..000000000000
--- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
+++ /dev/null
@@ -1,143 +0,0 @@
-Analog Devices ADV7511(W)/13/33/35 HDMI Encoders
-------------------------------------------------
-
-The ADV7511, ADV7511W, ADV7513, ADV7533 and ADV7535 are HDMI audio and video
-transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space
-conversion, S/PDIF, CEC and HDCP. ADV7533/5 supports the DSI interface for input
-pixels, while the others support RGB interface.
-
-Required properties:
-
-- compatible: Should be one of:
-		"adi,adv7511"
-		"adi,adv7511w"
-		"adi,adv7513"
-		"adi,adv7533"
-		"adi,adv7535"
-
-- reg: I2C slave addresses
-  The ADV7511 internal registers are split into four pages exposed through
-  different I2C addresses, creating four register maps. Each map has it own
-  I2C address and acts as a standard slave device on the I2C bus. The main
-  address is mandatory, others are optional and revert to defaults if not
-  specified.
-
-
-The ADV7511 supports a large number of input data formats that differ by their
-color depth, color format, clock mode, bit justification and random
-arrangement of components on the data bus. The combination of the following
-properties describe the input and map directly to the video input tables of the
-ADV7511 datasheet that document all the supported combinations.
-
-- adi,input-depth: Number of bits per color component at the input (8, 10 or
-  12).
-- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
-  "yuv444".
-- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
-  pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
-  data driven on both edges).
-
-The following input format properties are required except in "rgb 1x" and
-"yuv444 1x" modes, in which case they must not be specified.
-
-- adi,input-style: The input components arrangement variant (1, 2 or 3), as
-  listed in the input format tables in the datasheet.
-- adi,input-justification: The input bit justification ("left", "evenly",
-  "right").
-
-- avdd-supply: A 1.8V supply that powers up the AVDD pin on the chip.
-- dvdd-supply: A 1.8V supply that powers up the DVDD pin on the chip.
-- pvdd-supply: A 1.8V supply that powers up the PVDD pin on the chip.
-- dvdd-3v-supply: A 3.3V supply that powers up the pin called DVDD_3V
-  on the chip.
-- bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is
-  needed only for ADV7511.
-
-The following properties are required for ADV7533 and ADV7535:
-
-- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
-  be one of 1, 2, 3 or 4.
-- a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip.
-- v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip.
-- v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be
-  either 1.2V or 1.8V for ADV7533 but only 1.8V for ADV7535.
-
-Optional properties:
-
-- interrupts: Specifier for the ADV7511 interrupt
-- pd-gpios: Specifier for the GPIO connected to the power down signal
-
-- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
-  (-1200 ps .. 1600 ps). Defaults to no delay.
-- adi,embedded-sync: The input uses synchronization signals embedded in the
-  data stream (similar to BT.656). Defaults to separate H/V synchronization
-  signals.
-- adi,disable-timing-generator: Only for ADV7533 and ADV7535. Disables the
-  internal timing generator. The chip will rely on the sync signals in the
-  DSI data lanes, rather than generate its own timings for HDMI output.
-- clocks: from common clock binding: reference to the CEC clock.
-- clock-names: from common clock binding: must be "cec".
-- reg-names : Names of maps with programmable addresses.
-	It can contain any map needing a non-default address.
-	Possible maps names are : "main", "edid", "cec", "packet"
-
-Required nodes:
-
-The ADV7511 has two video ports. Their connections are modelled using the OF
-graph bindings specified in Documentation/devicetree/bindings/graph.txt.
-
-- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533/5, the
-  remote endpoint phandle should be a reference to a valid mipi_dsi_host device
-  node.
-- Video port 1 for the HDMI output
-- Audio port 2 for the HDMI audio input
-
-
-Example
--------
-
-	adv7511w: hdmi@39 {
-		compatible = "adi,adv7511w";
-		/*
-		 * The EDID page will be accessible on address 0x66 on the I2C
-		 * bus. All other maps continue to use their default addresses.
-		 */
-		reg = <0x39>, <0x66>;
-		reg-names = "main", "edid";
-		interrupt-parent = <&gpio3>;
-		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
-		clocks = <&cec_clock>;
-		clock-names = "cec";
-
-		adi,input-depth = <8>;
-		adi,input-colorspace = "rgb";
-		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7511w_in: endpoint {
-					remote-endpoint = <&dpi_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				adv7511_out: endpoint {
-					remote-endpoint = <&hdmi_connector_in>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-				codec_endpoint: endpoint {
-					remote-endpoint = <&i2s0_cpu_endpoint>;
-				};
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
new file mode 100644
index 000000000000..71b344e812dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
@@ -0,0 +1,231 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/adi,adv7511.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7511/11W/13 HDMI Encoders
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+description: |
+  The ADV7511, ADV7511W and ADV7513 are HDMI audio and video
+  transmitters compatible with HDMI 1.4 and DVI 1.0. They support color
+  space conversion, S/PDIF, CEC and HDCP. The transmitter input is
+  parallel RGB or YUV data.
+
+properties:
+  compatible:
+    enum:
+      - adi,adv7511
+      - adi,adv7511w
+      - adi,adv7513
+
+  reg:
+    description: |
+      I2C slave addresses.
+
+      The ADV7511/11W/13 internal registers are split into four pages
+      exposed through different I2C addresses, creating four register
+      maps. Each map has it own I2C address and acts as a standard slave
+      device on the I2C bus. The main address is mandatory, others are
+      optional and revert to defaults if not specified.
+    minItems: 1
+    maxItems: 4
+
+  reg-names:
+    description:
+      Names of maps with programmable addresses. It can contain any map
+      needing a non-default address.
+    minItems: 1
+    items:
+      - const: main
+      - const: edid
+      - const: cec
+      - const: packet
+
+  clocks:
+    description: Reference to the CEC clock.
+    maxItems: 1
+
+  clock-names:
+    const: cec
+
+  interrupts:
+    maxItems: 1
+
+  pd-gpios:
+    description: GPIO connected to the power down signal.
+    maxItems: 1
+
+  avdd-supply:
+    description: A 1.8V supply that powers up the AVDD pin.
+
+  dvdd-supply:
+    description: A 1.8V supply that powers up the DVDD pin.
+
+  pvdd-supply:
+    description: A 1.8V supply that powers up the PVDD pin.
+
+  dvdd-3v-supply:
+    description: A 3.3V supply that powers up the DVDD_3V pin.
+
+  bgvdd-supply:
+    description: A 1.8V supply that powers up the BGVDD pin.
+
+  adi,input-depth:
+    description: Number of bits per color component at the input.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 8, 10, 12 ]
+
+  adi,input-colorspace:
+    description: Input color space.
+    enum: [ rgb, yuv422, yuv444 ]
+
+  adi,input-clock:
+    description: |
+      Input clock type.
+        "1x": one clock cycle per pixel
+        "2x": two clock cycles per pixel
+        "dd": one clock cycle per pixel, data driven on both edges
+    enum: [ 1x, 2x, dd ]
+
+  adi,clock-delay:
+    description:
+      Video data clock delay relative to the pixel clock, in ps
+      (-1200ps .. 1600 ps).
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
+
+  adi,embedded-sync:
+    description:
+      If defined, the input uses synchronization signals embedded in the
+      data stream (similar to BT.656).
+    type: boolean
+
+  adi,input-style:
+    description:
+      Input components arrangement variant as listed in the input
+      format tables in the datasheet.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 1, 2, 3 ]
+
+  adi,input-justification:
+    description: Input bit justification.
+    enum: [ left, evenly, right ]
+
+  ports:
+    description:
+      The ADV7511(W)/13 has two video ports and one audio port. This node
+      models their connections as documented in
+      Documentation/devicetree/bindings/media/video-interfaces.txt
+      Documentation/devicetree/bindings/graph.txt
+    type: object
+    properties:
+      port@0:
+        description: Video port for the RGB or YUV input.
+        type: object
+
+      port@1:
+        description: Video port for the HDMI output.
+        type: object
+
+      port@2:
+        description: Audio port for the HDMI output.
+        type: object
+
+# adi,input-colorspace and adi,input-clock are required except in
+# "rgb 1x" and "yuv444 1x" modes, in which case they must not be
+# specified.
+if:
+  not:
+    properties:
+      adi,input-colorspace:
+        contains:
+          enum: [ rgb, yuv444 ]
+      adi,input-clock:
+        contains:
+          const: 1x
+
+then:
+  required:
+    - adi,input-style
+    - adi,input-justification
+
+else:
+  properties:
+    adi,input-style: false
+    adi,input-justification: false
+
+
+required:
+  - compatible
+  - reg
+  - ports
+  - adi,input-depth
+  - adi,input-colorspace
+  - adi,input-clock
+  - avdd-supply
+  - dvdd-supply
+  - pvdd-supply
+  - dvdd-3v-supply
+  - bgvdd-supply
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    adv7511w: hdmi@39 {
+        compatible = "adi,adv7511w";
+        /*
+         * The EDID page will be accessible on address 0x66 on the I2C
+         * bus. All other maps continue to use their default addresses.
+         */
+        reg = <0x39>, <0x66>;
+        reg-names = "main", "edid";
+        interrupt-parent = <&gpio3>;
+        interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+        clocks = <&cec_clock>;
+        clock-names = "cec";
+        avdd-supply = <&v1v8>;
+        dvdd-supply = <&v1v8>;
+        pvdd-supply = <&v1v8>;
+        dvdd-3v-supply = <&v3v3>;
+        bgvdd-supply = <&v1v8>;
+
+        adi,input-depth = <8>;
+        adi,input-colorspace = "yuv422";
+        adi,input-clock = "1x";
+
+        adi,input-style = <3>;
+        adi,input-justification = "right";
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                adv7511w_in: endpoint {
+                    remote-endpoint = <&dpi_out>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                adv7511_out: endpoint {
+                    remote-endpoint = <&hdmi_connector_in>;
+                };
+            };
+
+            port@2 {
+                reg = <2>;
+                codec_endpoint: endpoint {
+                    remote-endpoint = <&i2s0_cpu_endpoint>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml b/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
new file mode 100644
index 000000000000..18761f49e5fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/adi,adv7533.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7533/35 HDMI Encoders
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+description: |
+  The ADV7533 and ADV7535 are HDMI audio and video transmitters
+  compatible with HDMI 1.4 and DVI 1.0. They support color space
+  conversion, S/PDIF, CEC and HDCP. The transmitter input is MIPI DSI.
+
+properties:
+  compatible:
+    enum:
+      - adi,adv7533
+      - adi,adv7535
+
+  reg:
+    description: |
+      I2C slave addresses.
+
+      The ADV7533/35 internal registers are split into four pages
+      exposed through different I2C addresses, creating four register
+      maps. Each map has it own I2C address and acts as a standard slave
+      device on the I2C bus. The main address is mandatory, others are
+      optional and revert to defaults if not specified.
+    minItems: 1
+    maxItems: 4
+
+  reg-names:
+    description:
+      Names of maps with programmable addresses. It can contain any map
+      needing a non-default address.
+    minItems: 1
+    items:
+      - const: main
+      - const: edid
+      - const: cec
+      - const: packet
+
+  clocks:
+    description: Reference to the CEC clock.
+    maxItems: 1
+
+  clock-names:
+    const: cec
+
+  interrupts:
+    maxItems: 1
+
+  pd-gpios:
+    description: GPIO connected to the power down signal.
+    maxItems: 1
+
+  avdd-supply:
+    description: A 1.8V supply that powers up the AVDD pin.
+
+  dvdd-supply:
+    description: A 1.8V supply that powers up the DVDD pin.
+
+  pvdd-supply:
+    description: A 1.8V supply that powers up the PVDD pin.
+
+  a2vdd-supply:
+    description: A 1.8V supply that powers up the A2VDD pin.
+
+  v3p3-supply:
+    description: A 3.3V supply that powers up the V3P3 pin.
+
+  v1p2-supply:
+    description:
+      A supply that powers up the V1P2 pin. It can be either 1.2V
+      or 1.8V for ADV7533 but only 1.8V for ADV7535.
+
+  adi,disable-timing-generator:
+    description:
+      Disables the internal timing generator. The chip will rely on the
+      sync signals in the DSI data lanes, rather than generating its own
+      timings for HDMI output.
+    type: boolean
+
+  adi,dsi-lanes:
+    description: Number of DSI data lanes connected to the DSI host.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 1, 2, 3, 4 ]
+
+  ports:
+    description:
+      The ADV7533/35 has two video ports and one audio port. This node
+      models their connections as documented in
+      Documentation/devicetree/bindings/media/video-interfaces.txt
+      Documentation/devicetree/bindings/graph.txt
+    type: object
+    properties:
+      port@0:
+        description:
+          Video port for the DSI input. The remote endpoint phandle
+          should be a reference to a valid mipi_dsi_host_device.
+        type: object
+
+      port@1:
+        description: Video port for the HDMI output.
+        type: object
+
+      port@2:
+        description: Audio port for the HDMI output.
+        type: object
+
+required:
+  - compatible
+  - reg
+  - ports
+  - adi,dsi-lanes
+  - avdd-supply
+  - dvdd-supply
+  - pvdd-supply
+  - a2vdd-supply
+  - v3p3-supply
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    adv7533: hdmi@39 {
+        compatible = "adi,adv7533";
+        /*
+         * The EDID page will be accessible on address 0x66 on the I2C
+         * bus. All other maps continue to use their default addresses.
+         */
+        reg = <0x39>, <0x66>;
+        reg-names = "main", "edid";
+        interrupt-parent = <&gpio3>;
+        interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+        clocks = <&cec_clock>;
+        clock-names = "cec";
+        adi,dsi-lanes = <4>;
+        avdd-supply = <&v1v8>;
+        dvdd-supply = <&v1v8>;
+        pvdd-supply = <&v1v8>;
+        a2vdd-supply = <&v1v8>;
+        v3p3-supply = <&v3v3>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                adv7533_in: endpoint {
+                    remote-endpoint = <&dsi_out>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                adv7533_out: endpoint {
+                    remote-endpoint = <&hdmi_connector_in>;
+                };
+            };
+
+            port@2 {
+                reg = <2>;
+                codec_endpoint: endpoint {
+                    remote-endpoint = <&i2s0_cpu_endpoint>;
+                };
+            };
+        };
+    };
+
+...
-- 
2.18.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/4] ARM: dts: stm32: make hdmi-transmitter node compliant with DT bindings

[Laurent Pinchart]

Hi Ricardo,

Thank you for the patch.

On Mon, Jun 01, 2020 at 08:33:07AM +0200, Ricardo Cañuelo wrote:
> Reorder the I2C slave addresses of the hdmi-transmitter node and remove
> the adi,input-style and adi,input-justification properties to meet the
> adi,adv7513 binding requirements.
> 
> Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>  arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 6 ++----
>  1 file changed, 2 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
> index 930202742a3f..b67a21a8698a 100644
> --- a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
> +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
> @@ -185,8 +185,8 @@
>  &i2c4 {
>  	hdmi-transmitter@3d {
>  		compatible = "adi,adv7513";
> -		reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
> -		reg-names = "main", "cec", "edid", "packet";
> +		reg = <0x3d>, <0x4d>, <0x2d> , <0x5d>;
> +		reg-names = "main", "edid", "cec", "packet";
>  		clocks = <&cec_clock>;
>  		clock-names = "cec";
>  
> @@ -204,8 +204,6 @@
>  		adi,input-depth = <8>;
>  		adi,input-colorspace = "rgb";
>  		adi,input-clock = "1x";
> -		adi,input-style = <1>;
> -		adi,input-justification = "evenly";
>  
>  		ports {
>  			#address-cells = <1>;

-- 
Regards,

Laurent Pinchart

Re: [PATCH v3 3/4] ARM: dts: stm32: make hdmi-transmitter node compliant with DT bindings

[Laurent Pinchart]

Hi Ricardo,

Thank you for the patch.

On Mon, Jun 01, 2020 at 08:33:07AM +0200, Ricardo Cañuelo wrote:
> Reorder the I2C slave addresses of the hdmi-transmitter node and remove
> the adi,input-style and adi,input-justification properties to meet the
> adi,adv7513 binding requirements.
> 
> Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>  arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 6 ++----
>  1 file changed, 2 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
> index 930202742a3f..b67a21a8698a 100644
> --- a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
> +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
> @@ -185,8 +185,8 @@
>  &i2c4 {
>  	hdmi-transmitter@3d {
>  		compatible = "adi,adv7513";
> -		reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
> -		reg-names = "main", "cec", "edid", "packet";
> +		reg = <0x3d>, <0x4d>, <0x2d> , <0x5d>;
> +		reg-names = "main", "edid", "cec", "packet";
>  		clocks = <&cec_clock>;
>  		clock-names = "cec";
>  
> @@ -204,8 +204,6 @@
>  		adi,input-depth = <8>;
>  		adi,input-colorspace = "rgb";
>  		adi,input-clock = "1x";
> -		adi,input-style = <1>;
> -		adi,input-justification = "evenly";
>  
>  		ports {
>  			#address-cells = <1>;

-- 
Regards,

Laurent Pinchart

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 4/4] dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml

[Laurent Pinchart]

Hi Ricardo,

Thank you for the patch.

On Mon, Jun 01, 2020 at 08:33:08AM +0200, Ricardo Cañuelo wrote:
> Convert the ADV7511/11w/13/33/35 DT bindings to json-schema. The
> original binding has been split into two files: adi,adv7511.yaml for
> ADV7511/11W/13 and adi,adv7533.yaml for ADV7533/35.
> 
> Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Great work :-)

> ---
>  .../bindings/display/bridge/adi,adv7511.txt   | 143 -----------
>  .../bindings/display/bridge/adi,adv7511.yaml  | 231 ++++++++++++++++++
>  .../bindings/display/bridge/adi,adv7533.yaml  | 175 +++++++++++++
>  3 files changed, 406 insertions(+), 143 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
> deleted file mode 100644
> index 659523f538bf..000000000000
> --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
> +++ /dev/null
> @@ -1,143 +0,0 @@
> -Analog Devices ADV7511(W)/13/33/35 HDMI Encoders
> -------------------------------------------------
> -
> -The ADV7511, ADV7511W, ADV7513, ADV7533 and ADV7535 are HDMI audio and video
> -transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space
> -conversion, S/PDIF, CEC and HDCP. ADV7533/5 supports the DSI interface for input
> -pixels, while the others support RGB interface.
> -
> -Required properties:
> -
> -- compatible: Should be one of:
> -		"adi,adv7511"
> -		"adi,adv7511w"
> -		"adi,adv7513"
> -		"adi,adv7533"
> -		"adi,adv7535"
> -
> -- reg: I2C slave addresses
> -  The ADV7511 internal registers are split into four pages exposed through
> -  different I2C addresses, creating four register maps. Each map has it own
> -  I2C address and acts as a standard slave device on the I2C bus. The main
> -  address is mandatory, others are optional and revert to defaults if not
> -  specified.
> -
> -
> -The ADV7511 supports a large number of input data formats that differ by their
> -color depth, color format, clock mode, bit justification and random
> -arrangement of components on the data bus. The combination of the following
> -properties describe the input and map directly to the video input tables of the
> -ADV7511 datasheet that document all the supported combinations.
> -
> -- adi,input-depth: Number of bits per color component at the input (8, 10 or
> -  12).
> -- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
> -  "yuv444".
> -- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
> -  pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
> -  data driven on both edges).
> -
> -The following input format properties are required except in "rgb 1x" and
> -"yuv444 1x" modes, in which case they must not be specified.
> -
> -- adi,input-style: The input components arrangement variant (1, 2 or 3), as
> -  listed in the input format tables in the datasheet.
> -- adi,input-justification: The input bit justification ("left", "evenly",
> -  "right").
> -
> -- avdd-supply: A 1.8V supply that powers up the AVDD pin on the chip.
> -- dvdd-supply: A 1.8V supply that powers up the DVDD pin on the chip.
> -- pvdd-supply: A 1.8V supply that powers up the PVDD pin on the chip.
> -- dvdd-3v-supply: A 3.3V supply that powers up the pin called DVDD_3V
> -  on the chip.
> -- bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is
> -  needed only for ADV7511.
> -
> -The following properties are required for ADV7533 and ADV7535:
> -
> -- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
> -  be one of 1, 2, 3 or 4.
> -- a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip.
> -- v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip.
> -- v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be
> -  either 1.2V or 1.8V for ADV7533 but only 1.8V for ADV7535.
> -
> -Optional properties:
> -
> -- interrupts: Specifier for the ADV7511 interrupt
> -- pd-gpios: Specifier for the GPIO connected to the power down signal
> -
> -- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
> -  (-1200 ps .. 1600 ps). Defaults to no delay.
> -- adi,embedded-sync: The input uses synchronization signals embedded in the
> -  data stream (similar to BT.656). Defaults to separate H/V synchronization
> -  signals.
> -- adi,disable-timing-generator: Only for ADV7533 and ADV7535. Disables the
> -  internal timing generator. The chip will rely on the sync signals in the
> -  DSI data lanes, rather than generate its own timings for HDMI output.
> -- clocks: from common clock binding: reference to the CEC clock.
> -- clock-names: from common clock binding: must be "cec".
> -- reg-names : Names of maps with programmable addresses.
> -	It can contain any map needing a non-default address.
> -	Possible maps names are : "main", "edid", "cec", "packet"
> -
> -Required nodes:
> -
> -The ADV7511 has two video ports. Their connections are modelled using the OF
> -graph bindings specified in Documentation/devicetree/bindings/graph.txt.
> -
> -- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533/5, the
> -  remote endpoint phandle should be a reference to a valid mipi_dsi_host device
> -  node.
> -- Video port 1 for the HDMI output
> -- Audio port 2 for the HDMI audio input
> -
> -
> -Example
> --------
> -
> -	adv7511w: hdmi@39 {
> -		compatible = "adi,adv7511w";
> -		/*
> -		 * The EDID page will be accessible on address 0x66 on the I2C
> -		 * bus. All other maps continue to use their default addresses.
> -		 */
> -		reg = <0x39>, <0x66>;
> -		reg-names = "main", "edid";
> -		interrupt-parent = <&gpio3>;
> -		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
> -		clocks = <&cec_clock>;
> -		clock-names = "cec";
> -
> -		adi,input-depth = <8>;
> -		adi,input-colorspace = "rgb";
> -		adi,input-clock = "1x";
> -		adi,input-style = <1>;
> -		adi,input-justification = "evenly";
> -
> -		ports {
> -			#address-cells = <1>;
> -			#size-cells = <0>;
> -
> -			port@0 {
> -				reg = <0>;
> -				adv7511w_in: endpoint {
> -					remote-endpoint = <&dpi_out>;
> -				};
> -			};
> -
> -			port@1 {
> -				reg = <1>;
> -				adv7511_out: endpoint {
> -					remote-endpoint = <&hdmi_connector_in>;
> -				};
> -			};
> -
> -			port@2 {
> -				reg = <2>;
> -				codec_endpoint: endpoint {
> -					remote-endpoint = <&i2s0_cpu_endpoint>;
> -				};
> -			};
> -		};
> -	};
> diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
> new file mode 100644
> index 000000000000..71b344e812dd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
> @@ -0,0 +1,231 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/bridge/adi,adv7511.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices ADV7511/11W/13 HDMI Encoders
> +
> +maintainers:
> +  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> +
> +description: |
> +  The ADV7511, ADV7511W and ADV7513 are HDMI audio and video
> +  transmitters compatible with HDMI 1.4 and DVI 1.0. They support color
> +  space conversion, S/PDIF, CEC and HDCP. The transmitter input is
> +  parallel RGB or YUV data.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,adv7511
> +      - adi,adv7511w
> +      - adi,adv7513
> +
> +  reg:
> +    description: |
> +      I2C slave addresses.
> +
> +      The ADV7511/11W/13 internal registers are split into four pages
> +      exposed through different I2C addresses, creating four register
> +      maps. Each map has it own I2C address and acts as a standard slave
> +      device on the I2C bus. The main address is mandatory, others are
> +      optional and revert to defaults if not specified.
> +    minItems: 1
> +    maxItems: 4
> +
> +  reg-names:
> +    description:
> +      Names of maps with programmable addresses. It can contain any map
> +      needing a non-default address.
> +    minItems: 1
> +    items:
> +      - const: main
> +      - const: edid
> +      - const: cec
> +      - const: packet
> +
> +  clocks:
> +    description: Reference to the CEC clock.
> +    maxItems: 1
> +
> +  clock-names:
> +    const: cec
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  pd-gpios:
> +    description: GPIO connected to the power down signal.
> +    maxItems: 1
> +
> +  avdd-supply:
> +    description: A 1.8V supply that powers up the AVDD pin.
> +
> +  dvdd-supply:
> +    description: A 1.8V supply that powers up the DVDD pin.
> +
> +  pvdd-supply:
> +    description: A 1.8V supply that powers up the PVDD pin.
> +
> +  dvdd-3v-supply:
> +    description: A 3.3V supply that powers up the DVDD_3V pin.
> +
> +  bgvdd-supply:
> +    description: A 1.8V supply that powers up the BGVDD pin.
> +
> +  adi,input-depth:
> +    description: Number of bits per color component at the input.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - enum: [ 8, 10, 12 ]
> +
> +  adi,input-colorspace:
> +    description: Input color space.
> +    enum: [ rgb, yuv422, yuv444 ]
> +
> +  adi,input-clock:
> +    description: |
> +      Input clock type.
> +        "1x": one clock cycle per pixel
> +        "2x": two clock cycles per pixel
> +        "dd": one clock cycle per pixel, data driven on both edges
> +    enum: [ 1x, 2x, dd ]
> +
> +  adi,clock-delay:
> +    description:
> +      Video data clock delay relative to the pixel clock, in ps
> +      (-1200ps .. 1600 ps).
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    default: 0
> +
> +  adi,embedded-sync:
> +    description:
> +      If defined, the input uses synchronization signals embedded in the
> +      data stream (similar to BT.656).
> +    type: boolean
> +
> +  adi,input-style:
> +    description:
> +      Input components arrangement variant as listed in the input
> +      format tables in the datasheet.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 1, 2, 3 ]
> +
> +  adi,input-justification:
> +    description: Input bit justification.
> +    enum: [ left, evenly, right ]
> +
> +  ports:
> +    description:
> +      The ADV7511(W)/13 has two video ports and one audio port. This node
> +      models their connections as documented in
> +      Documentation/devicetree/bindings/media/video-interfaces.txt
> +      Documentation/devicetree/bindings/graph.txt
> +    type: object
> +    properties:
> +      port@0:
> +        description: Video port for the RGB or YUV input.
> +        type: object
> +
> +      port@1:
> +        description: Video port for the HDMI output.
> +        type: object
> +
> +      port@2:
> +        description: Audio port for the HDMI output.
> +        type: object
> +
> +# adi,input-colorspace and adi,input-clock are required except in
> +# "rgb 1x" and "yuv444 1x" modes, in which case they must not be
> +# specified.
> +if:
> +  not:
> +    properties:
> +      adi,input-colorspace:
> +        contains:
> +          enum: [ rgb, yuv444 ]
> +      adi,input-clock:
> +        contains:
> +          const: 1x
> +
> +then:
> +  required:
> +    - adi,input-style
> +    - adi,input-justification
> +
> +else:
> +  properties:
> +    adi,input-style: false
> +    adi,input-justification: false
> +
> +
> +required:
> +  - compatible
> +  - reg
> +  - ports
> +  - adi,input-depth
> +  - adi,input-colorspace
> +  - adi,input-clock
> +  - avdd-supply
> +  - dvdd-supply
> +  - pvdd-supply
> +  - dvdd-3v-supply
> +  - bgvdd-supply
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    adv7511w: hdmi@39 {
> +        compatible = "adi,adv7511w";
> +        /*
> +         * The EDID page will be accessible on address 0x66 on the I2C
> +         * bus. All other maps continue to use their default addresses.
> +         */
> +        reg = <0x39>, <0x66>;
> +        reg-names = "main", "edid";
> +        interrupt-parent = <&gpio3>;
> +        interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
> +        clocks = <&cec_clock>;
> +        clock-names = "cec";
> +        avdd-supply = <&v1v8>;
> +        dvdd-supply = <&v1v8>;
> +        pvdd-supply = <&v1v8>;
> +        dvdd-3v-supply = <&v3v3>;
> +        bgvdd-supply = <&v1v8>;
> +
> +        adi,input-depth = <8>;
> +        adi,input-colorspace = "yuv422";
> +        adi,input-clock = "1x";
> +
> +        adi,input-style = <3>;
> +        adi,input-justification = "right";
> +        ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            port@0 {
> +                reg = <0>;
> +                adv7511w_in: endpoint {
> +                    remote-endpoint = <&dpi_out>;
> +                };
> +            };
> +
> +            port@1 {
> +                reg = <1>;
> +                adv7511_out: endpoint {
> +                    remote-endpoint = <&hdmi_connector_in>;
> +                };
> +            };
> +
> +            port@2 {
> +                reg = <2>;
> +                codec_endpoint: endpoint {
> +                    remote-endpoint = <&i2s0_cpu_endpoint>;
> +                };
> +            };
> +        };
> +    };
> +
> +...
> diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml b/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
> new file mode 100644
> index 000000000000..18761f49e5fe
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
> @@ -0,0 +1,175 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/bridge/adi,adv7533.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices ADV7533/35 HDMI Encoders
> +
> +maintainers:
> +  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> +
> +description: |
> +  The ADV7533 and ADV7535 are HDMI audio and video transmitters
> +  compatible with HDMI 1.4 and DVI 1.0. They support color space
> +  conversion, S/PDIF, CEC and HDCP. The transmitter input is MIPI DSI.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,adv7533
> +      - adi,adv7535
> +
> +  reg:
> +    description: |
> +      I2C slave addresses.
> +
> +      The ADV7533/35 internal registers are split into four pages
> +      exposed through different I2C addresses, creating four register
> +      maps. Each map has it own I2C address and acts as a standard slave
> +      device on the I2C bus. The main address is mandatory, others are
> +      optional and revert to defaults if not specified.
> +    minItems: 1
> +    maxItems: 4
> +
> +  reg-names:
> +    description:
> +      Names of maps with programmable addresses. It can contain any map
> +      needing a non-default address.
> +    minItems: 1
> +    items:
> +      - const: main
> +      - const: edid
> +      - const: cec
> +      - const: packet
> +
> +  clocks:
> +    description: Reference to the CEC clock.
> +    maxItems: 1
> +
> +  clock-names:
> +    const: cec
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  pd-gpios:
> +    description: GPIO connected to the power down signal.
> +    maxItems: 1
> +
> +  avdd-supply:
> +    description: A 1.8V supply that powers up the AVDD pin.
> +
> +  dvdd-supply:
> +    description: A 1.8V supply that powers up the DVDD pin.
> +
> +  pvdd-supply:
> +    description: A 1.8V supply that powers up the PVDD pin.
> +
> +  a2vdd-supply:
> +    description: A 1.8V supply that powers up the A2VDD pin.
> +
> +  v3p3-supply:
> +    description: A 3.3V supply that powers up the V3P3 pin.
> +
> +  v1p2-supply:
> +    description:
> +      A supply that powers up the V1P2 pin. It can be either 1.2V
> +      or 1.8V for ADV7533 but only 1.8V for ADV7535.
> +
> +  adi,disable-timing-generator:
> +    description:
> +      Disables the internal timing generator. The chip will rely on the
> +      sync signals in the DSI data lanes, rather than generating its own
> +      timings for HDMI output.
> +    type: boolean
> +
> +  adi,dsi-lanes:
> +    description: Number of DSI data lanes connected to the DSI host.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 1, 2, 3, 4 ]
> +
> +  ports:
> +    description:
> +      The ADV7533/35 has two video ports and one audio port. This node
> +      models their connections as documented in
> +      Documentation/devicetree/bindings/media/video-interfaces.txt
> +      Documentation/devicetree/bindings/graph.txt
> +    type: object
> +    properties:
> +      port@0:
> +        description:
> +          Video port for the DSI input. The remote endpoint phandle
> +          should be a reference to a valid mipi_dsi_host_device.
> +        type: object
> +
> +      port@1:
> +        description: Video port for the HDMI output.
> +        type: object
> +
> +      port@2:
> +        description: Audio port for the HDMI output.
> +        type: object
> +
> +required:
> +  - compatible
> +  - reg
> +  - ports
> +  - adi,dsi-lanes
> +  - avdd-supply
> +  - dvdd-supply
> +  - pvdd-supply
> +  - a2vdd-supply
> +  - v3p3-supply
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    adv7533: hdmi@39 {
> +        compatible = "adi,adv7533";
> +        /*
> +         * The EDID page will be accessible on address 0x66 on the I2C
> +         * bus. All other maps continue to use their default addresses.
> +         */
> +        reg = <0x39>, <0x66>;
> +        reg-names = "main", "edid";
> +        interrupt-parent = <&gpio3>;
> +        interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
> +        clocks = <&cec_clock>;
> +        clock-names = "cec";
> +        adi,dsi-lanes = <4>;
> +        avdd-supply = <&v1v8>;
> +        dvdd-supply = <&v1v8>;
> +        pvdd-supply = <&v1v8>;
> +        a2vdd-supply = <&v1v8>;
> +        v3p3-supply = <&v3v3>;
> +
> +        ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            port@0 {
> +                reg = <0>;
> +                adv7533_in: endpoint {
> +                    remote-endpoint = <&dsi_out>;
> +                };
> +            };
> +
> +            port@1 {
> +                reg = <1>;
> +                adv7533_out: endpoint {
> +                    remote-endpoint = <&hdmi_connector_in>;
> +                };
> +            };
> +
> +            port@2 {
> +                reg = <2>;
> +                codec_endpoint: endpoint {
> +                    remote-endpoint = <&i2s0_cpu_endpoint>;
> +                };
> +            };
> +        };
> +    };
> +
> +...
> -- 
> 2.18.0
> 

-- 
Regards,

Laurent Pinchart

Re: [PATCH v3 4/4] dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml

[Laurent Pinchart]

Hi Ricardo,

Thank you for the patch.

On Mon, Jun 01, 2020 at 08:33:08AM +0200, Ricardo Cañuelo wrote:
> Convert the ADV7511/11w/13/33/35 DT bindings to json-schema. The
> original binding has been split into two files: adi,adv7511.yaml for
> ADV7511/11W/13 and adi,adv7533.yaml for ADV7533/35.
> 
> Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Great work :-)

> ---
>  .../bindings/display/bridge/adi,adv7511.txt   | 143 -----------
>  .../bindings/display/bridge/adi,adv7511.yaml  | 231 ++++++++++++++++++
>  .../bindings/display/bridge/adi,adv7533.yaml  | 175 +++++++++++++
>  3 files changed, 406 insertions(+), 143 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
> deleted file mode 100644
> index 659523f538bf..000000000000
> --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
> +++ /dev/null
> @@ -1,143 +0,0 @@
> -Analog Devices ADV7511(W)/13/33/35 HDMI Encoders
> -------------------------------------------------
> -
> -The ADV7511, ADV7511W, ADV7513, ADV7533 and ADV7535 are HDMI audio and video
> -transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space
> -conversion, S/PDIF, CEC and HDCP. ADV7533/5 supports the DSI interface for input
> -pixels, while the others support RGB interface.
> -
> -Required properties:
> -
> -- compatible: Should be one of:
> -		"adi,adv7511"
> -		"adi,adv7511w"
> -		"adi,adv7513"
> -		"adi,adv7533"
> -		"adi,adv7535"
> -
> -- reg: I2C slave addresses
> -  The ADV7511 internal registers are split into four pages exposed through
> -  different I2C addresses, creating four register maps. Each map has it own
> -  I2C address and acts as a standard slave device on the I2C bus. The main
> -  address is mandatory, others are optional and revert to defaults if not
> -  specified.
> -
> -
> -The ADV7511 supports a large number of input data formats that differ by their
> -color depth, color format, clock mode, bit justification and random
> -arrangement of components on the data bus. The combination of the following
> -properties describe the input and map directly to the video input tables of the
> -ADV7511 datasheet that document all the supported combinations.
> -
> -- adi,input-depth: Number of bits per color component at the input (8, 10 or
> -  12).
> -- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
> -  "yuv444".
> -- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
> -  pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
> -  data driven on both edges).
> -
> -The following input format properties are required except in "rgb 1x" and
> -"yuv444 1x" modes, in which case they must not be specified.
> -
> -- adi,input-style: The input components arrangement variant (1, 2 or 3), as
> -  listed in the input format tables in the datasheet.
> -- adi,input-justification: The input bit justification ("left", "evenly",
> -  "right").
> -
> -- avdd-supply: A 1.8V supply that powers up the AVDD pin on the chip.
> -- dvdd-supply: A 1.8V supply that powers up the DVDD pin on the chip.
> -- pvdd-supply: A 1.8V supply that powers up the PVDD pin on the chip.
> -- dvdd-3v-supply: A 3.3V supply that powers up the pin called DVDD_3V
> -  on the chip.
> -- bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is
> -  needed only for ADV7511.
> -
> -The following properties are required for ADV7533 and ADV7535:
> -
> -- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
> -  be one of 1, 2, 3 or 4.
> -- a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip.
> -- v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip.
> -- v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be
> -  either 1.2V or 1.8V for ADV7533 but only 1.8V for ADV7535.
> -
> -Optional properties:
> -
> -- interrupts: Specifier for the ADV7511 interrupt
> -- pd-gpios: Specifier for the GPIO connected to the power down signal
> -
> -- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
> -  (-1200 ps .. 1600 ps). Defaults to no delay.
> -- adi,embedded-sync: The input uses synchronization signals embedded in the
> -  data stream (similar to BT.656). Defaults to separate H/V synchronization
> -  signals.
> -- adi,disable-timing-generator: Only for ADV7533 and ADV7535. Disables the
> -  internal timing generator. The chip will rely on the sync signals in the
> -  DSI data lanes, rather than generate its own timings for HDMI output.
> -- clocks: from common clock binding: reference to the CEC clock.
> -- clock-names: from common clock binding: must be "cec".
> -- reg-names : Names of maps with programmable addresses.
> -	It can contain any map needing a non-default address.
> -	Possible maps names are : "main", "edid", "cec", "packet"
> -
> -Required nodes:
> -
> -The ADV7511 has two video ports. Their connections are modelled using the OF
> -graph bindings specified in Documentation/devicetree/bindings/graph.txt.
> -
> -- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533/5, the
> -  remote endpoint phandle should be a reference to a valid mipi_dsi_host device
> -  node.
> -- Video port 1 for the HDMI output
> -- Audio port 2 for the HDMI audio input
> -
> -
> -Example
> --------
> -
> -	adv7511w: hdmi@39 {
> -		compatible = "adi,adv7511w";
> -		/*
> -		 * The EDID page will be accessible on address 0x66 on the I2C
> -		 * bus. All other maps continue to use their default addresses.
> -		 */
> -		reg = <0x39>, <0x66>;
> -		reg-names = "main", "edid";
> -		interrupt-parent = <&gpio3>;
> -		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
> -		clocks = <&cec_clock>;
> -		clock-names = "cec";
> -
> -		adi,input-depth = <8>;
> -		adi,input-colorspace = "rgb";
> -		adi,input-clock = "1x";
> -		adi,input-style = <1>;
> -		adi,input-justification = "evenly";
> -
> -		ports {
> -			#address-cells = <1>;
> -			#size-cells = <0>;
> -
> -			port@0 {
> -				reg = <0>;
> -				adv7511w_in: endpoint {
> -					remote-endpoint = <&dpi_out>;
> -				};
> -			};
> -
> -			port@1 {
> -				reg = <1>;
> -				adv7511_out: endpoint {
> -					remote-endpoint = <&hdmi_connector_in>;
> -				};
> -			};
> -
> -			port@2 {
> -				reg = <2>;
> -				codec_endpoint: endpoint {
> -					remote-endpoint = <&i2s0_cpu_endpoint>;
> -				};
> -			};
> -		};
> -	};
> diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
> new file mode 100644
> index 000000000000..71b344e812dd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
> @@ -0,0 +1,231 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/bridge/adi,adv7511.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices ADV7511/11W/13 HDMI Encoders
> +
> +maintainers:
> +  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> +
> +description: |
> +  The ADV7511, ADV7511W and ADV7513 are HDMI audio and video
> +  transmitters compatible with HDMI 1.4 and DVI 1.0. They support color
> +  space conversion, S/PDIF, CEC and HDCP. The transmitter input is
> +  parallel RGB or YUV data.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,adv7511
> +      - adi,adv7511w
> +      - adi,adv7513
> +
> +  reg:
> +    description: |
> +      I2C slave addresses.
> +
> +      The ADV7511/11W/13 internal registers are split into four pages
> +      exposed through different I2C addresses, creating four register
> +      maps. Each map has it own I2C address and acts as a standard slave
> +      device on the I2C bus. The main address is mandatory, others are
> +      optional and revert to defaults if not specified.
> +    minItems: 1
> +    maxItems: 4
> +
> +  reg-names:
> +    description:
> +      Names of maps with programmable addresses. It can contain any map
> +      needing a non-default address.
> +    minItems: 1
> +    items:
> +      - const: main
> +      - const: edid
> +      - const: cec
> +      - const: packet
> +
> +  clocks:
> +    description: Reference to the CEC clock.
> +    maxItems: 1
> +
> +  clock-names:
> +    const: cec
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  pd-gpios:
> +    description: GPIO connected to the power down signal.
> +    maxItems: 1
> +
> +  avdd-supply:
> +    description: A 1.8V supply that powers up the AVDD pin.
> +
> +  dvdd-supply:
> +    description: A 1.8V supply that powers up the DVDD pin.
> +
> +  pvdd-supply:
> +    description: A 1.8V supply that powers up the PVDD pin.
> +
> +  dvdd-3v-supply:
> +    description: A 3.3V supply that powers up the DVDD_3V pin.
> +
> +  bgvdd-supply:
> +    description: A 1.8V supply that powers up the BGVDD pin.
> +
> +  adi,input-depth:
> +    description: Number of bits per color component at the input.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - enum: [ 8, 10, 12 ]
> +
> +  adi,input-colorspace:
> +    description: Input color space.
> +    enum: [ rgb, yuv422, yuv444 ]
> +
> +  adi,input-clock:
> +    description: |
> +      Input clock type.
> +        "1x": one clock cycle per pixel
> +        "2x": two clock cycles per pixel
> +        "dd": one clock cycle per pixel, data driven on both edges
> +    enum: [ 1x, 2x, dd ]
> +
> +  adi,clock-delay:
> +    description:
> +      Video data clock delay relative to the pixel clock, in ps
> +      (-1200ps .. 1600 ps).
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    default: 0
> +
> +  adi,embedded-sync:
> +    description:
> +      If defined, the input uses synchronization signals embedded in the
> +      data stream (similar to BT.656).
> +    type: boolean
> +
> +  adi,input-style:
> +    description:
> +      Input components arrangement variant as listed in the input
> +      format tables in the datasheet.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 1, 2, 3 ]
> +
> +  adi,input-justification:
> +    description: Input bit justification.
> +    enum: [ left, evenly, right ]
> +
> +  ports:
> +    description:
> +      The ADV7511(W)/13 has two video ports and one audio port. This node
> +      models their connections as documented in
> +      Documentation/devicetree/bindings/media/video-interfaces.txt
> +      Documentation/devicetree/bindings/graph.txt
> +    type: object
> +    properties:
> +      port@0:
> +        description: Video port for the RGB or YUV input.
> +        type: object
> +
> +      port@1:
> +        description: Video port for the HDMI output.
> +        type: object
> +
> +      port@2:
> +        description: Audio port for the HDMI output.
> +        type: object
> +
> +# adi,input-colorspace and adi,input-clock are required except in
> +# "rgb 1x" and "yuv444 1x" modes, in which case they must not be
> +# specified.
> +if:
> +  not:
> +    properties:
> +      adi,input-colorspace:
> +        contains:
> +          enum: [ rgb, yuv444 ]
> +      adi,input-clock:
> +        contains:
> +          const: 1x
> +
> +then:
> +  required:
> +    - adi,input-style
> +    - adi,input-justification
> +
> +else:
> +  properties:
> +    adi,input-style: false
> +    adi,input-justification: false
> +
> +
> +required:
> +  - compatible
> +  - reg
> +  - ports
> +  - adi,input-depth
> +  - adi,input-colorspace
> +  - adi,input-clock
> +  - avdd-supply
> +  - dvdd-supply
> +  - pvdd-supply
> +  - dvdd-3v-supply
> +  - bgvdd-supply
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    adv7511w: hdmi@39 {
> +        compatible = "adi,adv7511w";
> +        /*
> +         * The EDID page will be accessible on address 0x66 on the I2C
> +         * bus. All other maps continue to use their default addresses.
> +         */
> +        reg = <0x39>, <0x66>;
> +        reg-names = "main", "edid";
> +        interrupt-parent = <&gpio3>;
> +        interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
> +        clocks = <&cec_clock>;
> +        clock-names = "cec";
> +        avdd-supply = <&v1v8>;
> +        dvdd-supply = <&v1v8>;
> +        pvdd-supply = <&v1v8>;
> +        dvdd-3v-supply = <&v3v3>;
> +        bgvdd-supply = <&v1v8>;
> +
> +        adi,input-depth = <8>;
> +        adi,input-colorspace = "yuv422";
> +        adi,input-clock = "1x";
> +
> +        adi,input-style = <3>;
> +        adi,input-justification = "right";
> +        ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            port@0 {
> +                reg = <0>;
> +                adv7511w_in: endpoint {
> +                    remote-endpoint = <&dpi_out>;
> +                };
> +            };
> +
> +            port@1 {
> +                reg = <1>;
> +                adv7511_out: endpoint {
> +                    remote-endpoint = <&hdmi_connector_in>;
> +                };
> +            };
> +
> +            port@2 {
> +                reg = <2>;
> +                codec_endpoint: endpoint {
> +                    remote-endpoint = <&i2s0_cpu_endpoint>;
> +                };
> +            };
> +        };
> +    };
> +
> +...
> diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml b/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
> new file mode 100644
> index 000000000000..18761f49e5fe
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
> @@ -0,0 +1,175 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/bridge/adi,adv7533.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices ADV7533/35 HDMI Encoders
> +
> +maintainers:
> +  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> +
> +description: |
> +  The ADV7533 and ADV7535 are HDMI audio and video transmitters
> +  compatible with HDMI 1.4 and DVI 1.0. They support color space
> +  conversion, S/PDIF, CEC and HDCP. The transmitter input is MIPI DSI.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,adv7533
> +      - adi,adv7535
> +
> +  reg:
> +    description: |
> +      I2C slave addresses.
> +
> +      The ADV7533/35 internal registers are split into four pages
> +      exposed through different I2C addresses, creating four register
> +      maps. Each map has it own I2C address and acts as a standard slave
> +      device on the I2C bus. The main address is mandatory, others are
> +      optional and revert to defaults if not specified.
> +    minItems: 1
> +    maxItems: 4
> +
> +  reg-names:
> +    description:
> +      Names of maps with programmable addresses. It can contain any map
> +      needing a non-default address.
> +    minItems: 1
> +    items:
> +      - const: main
> +      - const: edid
> +      - const: cec
> +      - const: packet
> +
> +  clocks:
> +    description: Reference to the CEC clock.
> +    maxItems: 1
> +
> +  clock-names:
> +    const: cec
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  pd-gpios:
> +    description: GPIO connected to the power down signal.
> +    maxItems: 1
> +
> +  avdd-supply:
> +    description: A 1.8V supply that powers up the AVDD pin.
> +
> +  dvdd-supply:
> +    description: A 1.8V supply that powers up the DVDD pin.
> +
> +  pvdd-supply:
> +    description: A 1.8V supply that powers up the PVDD pin.
> +
> +  a2vdd-supply:
> +    description: A 1.8V supply that powers up the A2VDD pin.
> +
> +  v3p3-supply:
> +    description: A 3.3V supply that powers up the V3P3 pin.
> +
> +  v1p2-supply:
> +    description:
> +      A supply that powers up the V1P2 pin. It can be either 1.2V
> +      or 1.8V for ADV7533 but only 1.8V for ADV7535.
> +
> +  adi,disable-timing-generator:
> +    description:
> +      Disables the internal timing generator. The chip will rely on the
> +      sync signals in the DSI data lanes, rather than generating its own
> +      timings for HDMI output.
> +    type: boolean
> +
> +  adi,dsi-lanes:
> +    description: Number of DSI data lanes connected to the DSI host.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 1, 2, 3, 4 ]
> +
> +  ports:
> +    description:
> +      The ADV7533/35 has two video ports and one audio port. This node
> +      models their connections as documented in
> +      Documentation/devicetree/bindings/media/video-interfaces.txt
> +      Documentation/devicetree/bindings/graph.txt
> +    type: object
> +    properties:
> +      port@0:
> +        description:
> +          Video port for the DSI input. The remote endpoint phandle
> +          should be a reference to a valid mipi_dsi_host_device.
> +        type: object
> +
> +      port@1:
> +        description: Video port for the HDMI output.
> +        type: object
> +
> +      port@2:
> +        description: Audio port for the HDMI output.
> +        type: object
> +
> +required:
> +  - compatible
> +  - reg
> +  - ports
> +  - adi,dsi-lanes
> +  - avdd-supply
> +  - dvdd-supply
> +  - pvdd-supply
> +  - a2vdd-supply
> +  - v3p3-supply
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    adv7533: hdmi@39 {
> +        compatible = "adi,adv7533";
> +        /*
> +         * The EDID page will be accessible on address 0x66 on the I2C
> +         * bus. All other maps continue to use their default addresses.
> +         */
> +        reg = <0x39>, <0x66>;
> +        reg-names = "main", "edid";
> +        interrupt-parent = <&gpio3>;
> +        interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
> +        clocks = <&cec_clock>;
> +        clock-names = "cec";
> +        adi,dsi-lanes = <4>;
> +        avdd-supply = <&v1v8>;
> +        dvdd-supply = <&v1v8>;
> +        pvdd-supply = <&v1v8>;
> +        a2vdd-supply = <&v1v8>;
> +        v3p3-supply = <&v3v3>;
> +
> +        ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            port@0 {
> +                reg = <0>;
> +                adv7533_in: endpoint {
> +                    remote-endpoint = <&dsi_out>;
> +                };
> +            };
> +
> +            port@1 {
> +                reg = <1>;
> +                adv7533_out: endpoint {
> +                    remote-endpoint = <&hdmi_connector_in>;
> +                };
> +            };
> +
> +            port@2 {
> +                reg = <2>;
> +                codec_endpoint: endpoint {
> +                    remote-endpoint = <&i2s0_cpu_endpoint>;
> +                };
> +            };
> +        };
> +    };
> +
> +...
> -- 
> 2.18.0
> 

-- 
Regards,

Laurent Pinchart

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 4/4] dt-bindings: drm: bridge: adi, adv7511.txt: convert to yaml

[Rob Herring]

On Mon, 01 Jun 2020 08:33:08 +0200, Ricardo Cañuelo wrote:
> Convert the ADV7511/11w/13/33/35 DT bindings to json-schema. The
> original binding has been split into two files: adi,adv7511.yaml for
> ADV7511/11W/13 and adi,adv7533.yaml for ADV7533/35.
> 
> Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
> ---
>  .../bindings/display/bridge/adi,adv7511.txt   | 143 -----------
>  .../bindings/display/bridge/adi,adv7511.yaml  | 231 ++++++++++++++++++
>  .../bindings/display/bridge/adi,adv7533.yaml  | 175 +++++++++++++
>  3 files changed, 406 insertions(+), 143 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 4/4] dt-bindings: drm: bridge: adi, adv7511.txt: convert to yaml

[Rob Herring]

On Mon, 01 Jun 2020 08:33:08 +0200, Ricardo Cañuelo wrote:
> Convert the ADV7511/11w/13/33/35 DT bindings to json-schema. The
> original binding has been split into two files: adi,adv7511.yaml for
> ADV7511/11W/13 and adi,adv7533.yaml for ADV7533/35.
> 
> Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
> ---
>  .../bindings/display/bridge/adi,adv7511.txt   | 143 -----------
>  .../bindings/display/bridge/adi,adv7511.yaml  | 231 ++++++++++++++++++
>  .../bindings/display/bridge/adi,adv7533.yaml  | 175 +++++++++++++
>  3 files changed, 406 insertions(+), 143 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 0/4] Convert adi,adv7511.txt DT bindings to yaml

[Ricardo Cañuelo]

Hi all,

Gentle ping to ask about the merge status of this series. All the
patches have been reviewed/acked.

Thanks Laurent, Rob and Michal for reviewing.

Cheers,
Ricardo

Re: [PATCH v3 0/4] Convert adi,adv7511.txt DT bindings to yaml

[Ricardo Cañuelo]

Hi all,

Gentle ping to ask about the merge status of this series. All the
patches have been reviewed/acked.

Thanks Laurent, Rob and Michal for reviewing.

Cheers,
Ricardo

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 2/4] arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT binding

[Wei Xu]

Hi Ricardo,

On 2020/6/1 14:33, Ricardo Cañuelo wrote:
> hi3660-hikey960.dts:
>   Define a 'ports' node for 'adv7533: adv7533@39' and the
>   'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
>   binding.
> 
>   This fills the requirements to meet the binding requirements,
>   remote endpoints are not defined.
> 
> hi6220-hikey.dts:
>   Change property name s/pd-gpio/pd-gpios, gpio properties should be
>   plural. This is just a cosmetic change.
> 
> Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Thanks!
Applied this patch only to the hisilicon arm64 dt tree since
it does not depend on the new yaml format binding.

Best Regards,
Wei

> ---
>  arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 11 +++++++++++
>  arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts    |  2 +-
>  2 files changed, 12 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
> index e035cf195b19..8c4bfbaf3a80 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
> @@ -530,6 +530,17 @@
>  		status = "ok";
>  		compatible = "adi,adv7533";
>  		reg = <0x39>;
> +		adi,dsi-lanes = <4>;
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			port@0 {
> +				reg = <0>;
> +			};
> +			port@1 {
> +				reg = <1>;
> +			};
> +		};
>  	};
>  };
>  
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> index c14205cd6bf5..3e47150c05ec 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> @@ -516,7 +516,7 @@
>  		reg = <0x39>;
>  		interrupt-parent = <&gpio1>;
>  		interrupts = <1 2>;
> -		pd-gpio = <&gpio0 4 0>;
> +		pd-gpios = <&gpio0 4 0>;
>  		adi,dsi-lanes = <4>;
>  		#sound-dai-cells = <0>;
>  
> 

Re: [PATCH v3 2/4] arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT binding

[Wei Xu]

Hi Ricardo,

On 2020/6/1 14:33, Ricardo Cañuelo wrote:
> hi3660-hikey960.dts:
>   Define a 'ports' node for 'adv7533: adv7533@39' and the
>   'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
>   binding.
> 
>   This fills the requirements to meet the binding requirements,
>   remote endpoints are not defined.
> 
> hi6220-hikey.dts:
>   Change property name s/pd-gpio/pd-gpios, gpio properties should be
>   plural. This is just a cosmetic change.
> 
> Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Thanks!
Applied this patch only to the hisilicon arm64 dt tree since
it does not depend on the new yaml format binding.

Best Regards,
Wei

> ---
>  arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 11 +++++++++++
>  arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts    |  2 +-
>  2 files changed, 12 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
> index e035cf195b19..8c4bfbaf3a80 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
> @@ -530,6 +530,17 @@
>  		status = "ok";
>  		compatible = "adi,adv7533";
>  		reg = <0x39>;
> +		adi,dsi-lanes = <4>;
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			port@0 {
> +				reg = <0>;
> +			};
> +			port@1 {
> +				reg = <1>;
> +			};
> +		};
>  	};
>  };
>  
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> index c14205cd6bf5..3e47150c05ec 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> @@ -516,7 +516,7 @@
>  		reg = <0x39>;
>  		interrupt-parent = <&gpio1>;
>  		interrupts = <1 2>;
> -		pd-gpio = <&gpio0 4 0>;
> +		pd-gpios = <&gpio0 4 0>;
>  		adi,dsi-lanes = <4>;
>  		#sound-dai-cells = <0>;
>  
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 2/4] arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT binding

[Ricardo Cañuelo]

Hi Wei,

On mar 21-07-2020 10:41:49, Wei Xu wrote:
> Hi Ricardo,
> 
> On 2020/6/1 14:33, Ricardo Cañuelo wrote:
> > hi3660-hikey960.dts:
> >   Define a 'ports' node for 'adv7533: adv7533@39' and the
> >   'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
> >   binding.
> > 
> >   This fills the requirements to meet the binding requirements,
> >   remote endpoints are not defined.
> > 
> > hi6220-hikey.dts:
> >   Change property name s/pd-gpio/pd-gpios, gpio properties should be
> >   plural. This is just a cosmetic change.
> > 
> > Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
> > Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> 
> Thanks!
> Applied this patch only to the hisilicon arm64 dt tree since
> it does not depend on the new yaml format binding.
> 
> Best Regards,
> Wei

Great, thanks!

Cheers,
Ricardo

Re: [PATCH v3 2/4] arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT binding

[Ricardo Cañuelo]

Hi Wei,

On mar 21-07-2020 10:41:49, Wei Xu wrote:
> Hi Ricardo,
> 
> On 2020/6/1 14:33, Ricardo Cañuelo wrote:
> > hi3660-hikey960.dts:
> >   Define a 'ports' node for 'adv7533: adv7533@39' and the
> >   'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
> >   binding.
> > 
> >   This fills the requirements to meet the binding requirements,
> >   remote endpoints are not defined.
> > 
> > hi6220-hikey.dts:
> >   Change property name s/pd-gpio/pd-gpios, gpio properties should be
> >   plural. This is just a cosmetic change.
> > 
> > Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
> > Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> 
> Thanks!
> Applied this patch only to the hisilicon arm64 dt tree since
> it does not depend on the new yaml format binding.
> 
> Best Regards,
> Wei

Great, thanks!

Cheers,
Ricardo

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel