All of lore.kernel.org
 help / color / mirror / Atom feed
From: Helmut Grohne <helmut.grohne@intenta.de>
To: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>,
	Heiner Kallweit <hkallweit1@gmail.com>,
	Russell King <linux@armlinux.org.uk>,
	"David S. Miller" <davem@davemloft.net>,
	Jakub Kicinski <kuba@kernel.org>, <netdev@vger.kernel.org>,
	Woojung Huh <woojung.huh@microchip.com>,
	"Microchip Linux Driver Support" <UNGLinuxDriver@microchip.com>,
	Vivien Didelot <vivien.didelot@gmail.com>,
	Tristram Ha <Tristram.Ha@microchip.com>
Subject: [PATCH v2] net: dsa: microchip: call phy_remove_link_mode during probe
Date: Thu, 16 Jul 2020 14:57:24 +0200	[thread overview]
Message-ID: <20200716125723.GA19500@laureti-dev> (raw)
In-Reply-To: <20200715192722.GD1256692@lunn.ch>

When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.

phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.

Therefore move the phy_remove_link_mode calls into ksz9477_setup. This
is called during dsa_switch_register and thus comes after
ksz9477_switch_detect, which initializes dev->features.

Remove phy_setup from ksz_dev_ops as no users remain.

Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c613019 ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
---
 drivers/net/dsa/microchip/ksz9477.c    | 31 ++++++++++----------------
 drivers/net/dsa/microchip/ksz_common.c |  2 --
 drivers/net/dsa/microchip/ksz_common.h |  2 --
 3 files changed, 12 insertions(+), 23 deletions(-)

changes since v1:
 * Don't change phy_remove_link_mode. Instead, call it at the right
   time. Thanks to Andrew Lunn for the detailed explanation.

Helmut

diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c
index 8d15c3016024..d0023916e1e8 100644
--- a/drivers/net/dsa/microchip/ksz9477.c
+++ b/drivers/net/dsa/microchip/ksz9477.c
@@ -974,23 +974,6 @@ static void ksz9477_port_mirror_del(struct dsa_switch *ds, int port,
 			     PORT_MIRROR_SNIFFER, false);
 }
 
-static void ksz9477_phy_setup(struct ksz_device *dev, int port,
-			      struct phy_device *phy)
-{
-	/* Only apply to port with PHY. */
-	if (port >= dev->phy_port_cnt)
-		return;
-
-	/* The MAC actually cannot run in 1000 half-duplex mode. */
-	phy_remove_link_mode(phy,
-			     ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
-
-	/* PHY does not support gigabit. */
-	if (!(dev->features & GBIT_SUPPORT))
-		phy_remove_link_mode(phy,
-				     ETHTOOL_LINK_MODE_1000baseT_Full_BIT);
-}
-
 static bool ksz9477_get_gbit(struct ksz_device *dev, u8 data)
 {
 	bool gbit;
@@ -1353,7 +1336,7 @@ static void ksz9477_config_cpu_port(struct dsa_switch *ds)
 static int ksz9477_setup(struct dsa_switch *ds)
 {
 	struct ksz_device *dev = ds->priv;
-	int ret = 0;
+	int ret = 0, i;
 
 	dev->vlan_cache = devm_kcalloc(dev->dev, sizeof(struct vlan_table),
 				       dev->num_vlans, GFP_KERNEL);
@@ -1391,6 +1374,17 @@ static int ksz9477_setup(struct dsa_switch *ds)
 
 	ksz_init_mib_timer(dev);
 
+	for (i = 0; i < dev->phy_port_cnt; ++i) {
+		/* The MAC actually cannot run in 1000 half-duplex mode. */
+		phy_remove_link_mode(&dev->ports[i].phydev,
+				     ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+
+		/* PHY does not support gigabit. */
+		if (!(dev->features & GBIT_SUPPORT))
+			phy_remove_link_mode(&dev->ports[i].phydev,
+					     ETHTOOL_LINK_MODE_1000baseT_Full_BIT);
+	}
+
 	return 0;
 }
 
@@ -1603,7 +1597,6 @@ static const struct ksz_dev_ops ksz9477_dev_ops = {
 	.get_port_addr = ksz9477_get_port_addr,
 	.cfg_port_member = ksz9477_cfg_port_member,
 	.flush_dyn_mac_table = ksz9477_flush_dyn_mac_table,
-	.phy_setup = ksz9477_phy_setup,
 	.port_setup = ksz9477_port_setup,
 	.r_mib_cnt = ksz9477_r_mib_cnt,
 	.r_mib_pkt = ksz9477_r_mib_pkt,
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index fd1d6676ae4f..7b6c0dce7536 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -358,8 +358,6 @@ int ksz_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
 
 	/* setup slave port */
 	dev->dev_ops->port_setup(dev, port, false);
-	if (dev->dev_ops->phy_setup)
-		dev->dev_ops->phy_setup(dev, port, phy);
 
 	/* port_stp_state_set() will be called after to enable the port so
 	 * there is no need to do anything.
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index f2c9bb68fd33..7d11dd32ec0d 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -119,8 +119,6 @@ struct ksz_dev_ops {
 	u32 (*get_port_addr)(int port, int offset);
 	void (*cfg_port_member)(struct ksz_device *dev, int port, u8 member);
 	void (*flush_dyn_mac_table)(struct ksz_device *dev, int port);
-	void (*phy_setup)(struct ksz_device *dev, int port,
-			  struct phy_device *phy);
 	void (*port_cleanup)(struct ksz_device *dev, int port);
 	void (*port_setup)(struct ksz_device *dev, int port, bool cpu_port);
 	void (*r_phy)(struct ksz_device *dev, u16 phy, u16 reg, u16 *val);
-- 
2.20.1


  reply	other threads:[~2020-07-16 12:57 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-14  8:25 [PATCH] net: phy: phy_remove_link_mode should not advertise new modes Helmut Grohne
2020-07-14 21:07 ` David Miller
2020-07-15  7:03   ` Helmut Grohne
2020-07-15 18:20     ` Jakub Kicinski
2020-07-15 19:01       ` Andrew Lunn
2020-07-15 18:51     ` Andrew Lunn
2020-07-15 19:27 ` Andrew Lunn
2020-07-16 12:57   ` Helmut Grohne [this message]
2020-07-16 14:10     ` [PATCH v2] net: dsa: microchip: call phy_remove_link_mode during probe Andrew Lunn
2020-07-17  8:18       ` Helmut Grohne
2020-07-17 13:18         ` Andrew Lunn
2020-07-20  9:04           ` [PATCH v3] " Helmut Grohne
2020-07-20 20:43             ` Andrew Lunn
2020-07-21 11:07               ` [PATCH v4] " Helmut Grohne
2020-07-21 15:20                 ` Andrew Lunn
2020-07-21 22:50                 ` David Miller
2020-07-20 21:04             ` [PATCH v3] " Andrew Lunn
2020-07-21  7:38               ` Helmut Grohne

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200716125723.GA19500@laureti-dev \
    --to=helmut.grohne@intenta.de \
    --cc=Tristram.Ha@microchip.com \
    --cc=UNGLinuxDriver@microchip.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=f.fainelli@gmail.com \
    --cc=hkallweit1@gmail.com \
    --cc=kuba@kernel.org \
    --cc=linux@armlinux.org.uk \
    --cc=netdev@vger.kernel.org \
    --cc=vivien.didelot@gmail.com \
    --cc=woojung.huh@microchip.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.