On Tue, Jun 23, 2020 at 04:55:27PM +0200, Thierry Reding wrote:
> From: Thierry Reding <treding-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
> 
> The XUSB pad controller, which provides access to various USB, PCI and
> SATA pads (or PHYs), needs to bring up the PLLs associated with these
> pads. In order to properly do so, it needs to control the power supplied
> to these PLLs.
> 
> Remove the PLL power supplies from the PCIe controller because it does
> not need direct access to them. Instead it will only use the configured
> pads provided by the XUSB pad controller.
> 
> Signed-off-by: Thierry Reding <treding-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
> ---
> Hi Rob,
> 
> I already made this change as part of the conversion series, but wanted
> to send this out as part of this subseries since it addresses a fairly
> long-standing issue that I'd like to clean up irrespective of the DT
> binding conversion. Since it looks like the conversion series will take
> a bit longer, I think it makes sense to send this out separately.
> 
> Thierry
> 
>  .../devicetree/bindings/pci/nvidia,tegra20-pcie.txt  | 12 ------------
>  1 file changed, 12 deletions(-)

Hi Rob, any feedback on this?

Thanks,
Thierry

> diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
> index 7939bca47861..d099f3476ccc 100644
> --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
> @@ -112,28 +112,16 @@ Power supplies for Tegra124:
>  - Required:
>    - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
>    - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
> -  - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
> -    supply 1.05 V.
>    - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
>      Must supply 3.3 V.
> -  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
> -    Must supply 3.3 V.
>    - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
>      supply 2.8-3.3 V.
> -  - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must
> -    supply 1.05 V.
>  
>  Power supplies for Tegra210:
>  - Required:
> -  - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must
> -    supply 1.05 V.
>    - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output
>      clocks. Must supply 1.8 V.
>    - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
> -  - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
> -    supply 1.05 V.
> -  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
> -    Must supply 3.3 V.
>    - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
>      supply 1.8 V.
>  
> -- 
> 2.27.0
>