From mboxrd@z Thu Jan 1 00:00:00 1970 From: Marek Vasut Date: Sat, 25 Jul 2020 16:50:56 +0200 Subject: [PATCH 2/2] ARM: dts: stm32: Add DHSOM based DRC02 board In-Reply-To: <20200725145056.537060-1-marex@denx.de> References: <20200725145056.537060-1-marex@denx.de> Message-ID: <20200725145056.537060-2-marex@denx.de> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Add DT for DH DRC02 unit, which is a universal controller device. The system has two ethernet ports, two CANs, RS485 and RS232, USB, capacitive buttons and an OLED display. Signed-off-by: Marek Vasut Cc: Patrice Chotard Cc: Patrick Delaunay --- arch/arm/dts/Makefile | 1 + .../dts/stm32mp15xx-dhcom-drc02-u-boot.dtsi | 6 + arch/arm/dts/stm32mp15xx-dhcom-drc02.dts | 158 ++++++++++++++++++ 3 files changed, 165 insertions(+) create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-drc02-u-boot.dtsi create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-drc02.dts diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 5726156a2d..58f3cd4207 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -936,6 +936,7 @@ dtb-$(CONFIG_STM32MP15x) += \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb \ + stm32mp15xx-dhcom-drc02.dtb \ stm32mp15xx-dhcom-pdk2.dtb \ stm32mp15xx-dhcor-avenger96.dtb diff --git a/arch/arm/dts/stm32mp15xx-dhcom-drc02-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcom-drc02-u-boot.dtsi new file mode 100644 index 0000000000..f83cfe90b8 --- /dev/null +++ b/arch/arm/dts/stm32mp15xx-dhcom-drc02-u-boot.dtsi @@ -0,0 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * Copyright (C) 2020 Marek Vasut + */ + +#include "stm32mp15xx-dhcom-u-boot.dtsi" diff --git a/arch/arm/dts/stm32mp15xx-dhcom-drc02.dts b/arch/arm/dts/stm32mp15xx-dhcom-drc02.dts new file mode 100644 index 0000000000..5a237a3b7b --- /dev/null +++ b/arch/arm/dts/stm32mp15xx-dhcom-drc02.dts @@ -0,0 +1,158 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * Copyright (C) 2020 Marek Vasut + */ + +#include "stm32mp15xx-dhcom.dtsi" + +/ { + model = "DH Electronics STM32MP15xx DHCOM DRC02"; + compatible = "dh,stm32mp15xx-dhcom-drc02", "st,stm32mp1xx"; + + aliases { + serial0 = &uart4; + serial1 = &usart3; + serial2 = &uart8; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&adc { + status = "disabled"; +}; + +&dac { + status = "disabled"; +}; + +&gpiob { + /* + * NOTE: On DRC02, the RS485_RX_En is controlled by a separate + * GPIO line, however the STM32 UART driver assumes RX happens + * during TX anyway and that it only controls drive enable DE + * line. Hence, the RX is always enabled here. + */ + usb-hub { + gpio-hog; + gpios = <8 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "rs485-rx-en"; + }; +}; + +&gpiod { + gpio-line-names = "", "", "", "", + "", "", "", "", + "", "", "", "Out1", + "Out2", "", "", ""; +}; + +&gpioi { + gpio-line-names = "In1", "", "", "", + "", "", "", "", + "In2", "", "", "", + "", "", "", ""; + + /* + * NOTE: The USB Hub on the DRC02 needs a reset signal to be + * pulled high in order to be detected by the USB Controller. + * This signal should be handled by USB power sequencing in + * order to reset the Hub when USB bus is powered down, but + * so far there is no such functionality. + */ + usb-hub { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb-hub-reset"; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; + + eeprom at 50 { + compatible = "atmel,24c04"; + reg = <0x50>; + pagesize = <16>; + }; +}; + +&i2c5 { /* TP7/TP8 */ + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; +}; + +&sdmmc3 { + /* + * On DRC02, the SoM does not have SDIO WiFi. The pins + * are used for on-board microSD slot instead. + */ + /delete-property/broken-cd; + cd-gpios = <&gpioi 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + disable-wp; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins_a>; + cs-gpios = <&gpioz 3 0>; + /* Use PIO for the display */ + /delete-property/dmas; + /delete-property/dma-names; + status = "disabled"; /* Enable once there is display driver */ + /* + * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are + * also connected to the display board connector. + */ +}; + +&usart3 { + pinctrl-names = "default"; + pinctrl-0 = <&usart3_pins_a>; + status = "okay"; +}; + +/* + * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1), + * however the STM32MP1 pinmux cannot map them to UART4 . + */ + +&uart8 { /* RS485 */ + pinctrl-names = "default"; + pinctrl-0 = <&uart8_pins_a>; + rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + status = "okay"; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; -- 2.27.0