Re: [RESENT PATCH net--stat 1/1] net: ethernet: fec: Revert "net: ethernet: fec: Replace interrupt driven MDIO with polled IO"

[Laurent Pinchart <laurent.pinchart@ideasonboard.com>]

Hi Andrew,

On Mon, Jul 27, 2020 at 04:14:32AM +0200, Andrew Lunn wrote:
> On Mon, Jul 27, 2020 at 05:06:31AM +0300, Laurent Pinchart wrote:
> > On Mon, Jul 27, 2020 at 04:24:02AM +0300, Laurent Pinchart wrote:
> > > On Mon, Apr 27, 2020 at 10:08:04PM +0800, Fugang Duan wrote:
> > > > This reverts commit 29ae6bd1b0d8a57d7c00ab12cbb949fc41986eef.
> > > > 
> > > > The commit breaks ethernet function on i.MX6SX, i.MX7D, i.MX8MM,
> > > > i.MX8MQ, and i.MX8QXP platforms. Boot yocto system by NFS mounting
> > > > rootfs will be failed with the commit.
> > > 
> > > I'm afraid this commit breaks networking on i.MX7D for me :-( My board
> > > is configured to boot over NFS root with IP autoconfiguration through
> > > DHCP. The DHCP request goes out, the reply it sent back by the server,
> > > but never noticed by the fec driver.
> > > 
> > > v5.7 works fine. As 29ae6bd1b0d8a57d7c00ab12cbb949fc41986eef was merged
> > > during the v5.8 merge window, I suspect something else cropped in
> > > between 29ae6bd1b0d8a57d7c00ab12cbb949fc41986eef and this patch that
> > > needs to be reverted too. We're close to v5.8 and it would be annoying
> > > to see this regression ending up in the released kernel. I can test
> > > patches, but I'm not familiar enough with the driver (or the networking
> > > subsystem) to fix the issue myself.
> > 
> > If it can be of any help, I've confirmed that, to get the network back
> > to usable state from v5.8-rc6, I have to revert all patches up to this
> > one. This is the top of my branch, on top of v5.8-rc6:
> > 
> > 5bbe80c9efea Revert "net: ethernet: fec: Revert "net: ethernet: fec: Replace interrupt driven MDIO with polled IO""
> > 5462896a08c1 Revert "net: ethernet: fec: Replace interrupt driven MDIO with polled IO"
> > 824a82e2bdfa Revert "net: ethernet: fec: move GPR register offset and bit into DT"
> > bfe330591cab Revert "net: fec: disable correct clk in the err path of fec_enet_clk_enable"
> > 109958cad578 Revert "net: ethernet: fec: prevent tx starvation under high rx load"
> 
> OK.
> 
> What PHY are you using? A Micrel?

KSZ9031RNXIA

> And which DT file?

It's out of tree.

&fec1 {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet1>;
        assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
                          <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
        assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
        assigned-clock-rates = <0>, <100000000>;
        phy-mode = "rgmii";
        phy-handle = <&ethphy0>;
        phy-reset-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
        phy-supply = <&reg_3v3_sw>;
        fsl,magic-packet;
        status = "okay";

        mdio {
                #address-cells = <1>;
                #size-cells = <0>;

                ethphy0: ethernet-phy@0 {
                        reg = <1>;
                };

                ethphy1: ethernet-phy@1 {
                        reg = <2>;
                };
        };
};

I can provide the full DT if needed. 

-- 
Regards,

Laurent Pinchart