All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v8 0/6] hwmon: pmbus: adm1266: add support
@ 2020-08-12 14:20 alexandru.tachici
  2020-08-12 14:20 ` [PATCH v8 1/6] " alexandru.tachici
                   ` (6 more replies)
  0 siblings, 7 replies; 9+ messages in thread
From: alexandru.tachici @ 2020-08-12 14:20 UTC (permalink / raw)
  To: linux-hwmon, linux-kernel, devicetree; +Cc: robh+dt, linux, Alexandru Tachici

From: Alexandru Tachici <alexandru.tachici@analog.com>

Add PMBus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.

1. Add PMBus probing driver for inputs vh1->vh4
and vp1->vp13.

2. Add Block Write-Read Process Call command.
A PMBus specific implementation was required because
block write with I2C_SMBUS_PROC_CALL flag allows a
maximum of 32 bytes to be received.

3. This makes adm1266 driver expose GPIOs
to user-space. Currently are read only. Future
developments on the firmware will allow
them to be writable.

4. Allow the current sate of the sequencer to be read
through debugfs.

5. Blackboxes are 64 bytes of chip state related data
that is generated on faults. Use the nvmem kernel api
to expose the blackbox chip functionality to userspace.

6. DT bindings for ADM1266.

Alexandru Tachici (6):
  hwmon: pmbus: adm1266: add support
  hwmon: pmbus: adm1266: Add Block process call
  hwmon: pmbus: adm1266: Add support for GPIOs
  hwmon: pmbus: adm1266: add debugfs for states
  hwmon: pmbus: adm1266: read blackbox
  dt-bindings: hwmon: Add bindings for ADM1266

Changelog v7 -> v8:
  - removed firmware/config programming
  - in adm1266_pmbus_block_xfer unlock buf mutex on error paths
  - added "depends on GPIOLIB" in kconfig ("select GPIOLIB" triggers a
  recursive dependency error)
  - removed cell access check (only blackbox cell will be used)
  - removed #if IS_ENABLED(CONFIG_NVMEM)
  - dt-bindings: removed adi,master-adm1266 property

 .../bindings/hwmon/adi,adm1266.yaml           |  51 ++
 Documentation/hwmon/adm1266.rst               |  37 ++
 Documentation/hwmon/index.rst                 |   1 +
 drivers/hwmon/pmbus/Kconfig                   |  11 +
 drivers/hwmon/pmbus/Makefile                  |   1 +
 drivers/hwmon/pmbus/adm1266.c                 | 513 ++++++++++++++++++
 6 files changed, 614 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/hwmon/adi,adm1266.yaml
 create mode 100644 Documentation/hwmon/adm1266.rst
 create mode 100644 drivers/hwmon/pmbus/adm1266.c

-- 
2.20.1


^ permalink raw reply	[flat|nested] 9+ messages in thread

* [PATCH v8 1/6] hwmon: pmbus: adm1266: add support
  2020-08-12 14:20 [PATCH v8 0/6] hwmon: pmbus: adm1266: add support alexandru.tachici
@ 2020-08-12 14:20 ` alexandru.tachici
  2020-08-12 14:20 ` [PATCH v8 2/6] hwmon: pmbus: adm1266: Add Block process call alexandru.tachici
                   ` (5 subsequent siblings)
  6 siblings, 0 replies; 9+ messages in thread
From: alexandru.tachici @ 2020-08-12 14:20 UTC (permalink / raw)
  To: linux-hwmon, linux-kernel, devicetree; +Cc: robh+dt, linux, Alexandru Tachici

From: Alexandru Tachici <alexandru.tachici@analog.com>

Add pmbus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
---
 Documentation/hwmon/adm1266.rst | 37 +++++++++++++++++++
 Documentation/hwmon/index.rst   |  1 +
 drivers/hwmon/pmbus/Kconfig     |  9 +++++
 drivers/hwmon/pmbus/Makefile    |  1 +
 drivers/hwmon/pmbus/adm1266.c   | 65 +++++++++++++++++++++++++++++++++
 5 files changed, 113 insertions(+)
 create mode 100644 Documentation/hwmon/adm1266.rst
 create mode 100644 drivers/hwmon/pmbus/adm1266.c

diff --git a/Documentation/hwmon/adm1266.rst b/Documentation/hwmon/adm1266.rst
new file mode 100644
index 000000000000..9257f8a48650
--- /dev/null
+++ b/Documentation/hwmon/adm1266.rst
@@ -0,0 +1,37 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver adm1266
+=====================
+
+Supported chips:
+  * Analog Devices ADM1266
+    Prefix: 'adm1266'
+    Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1266.pdf
+
+Author: Alexandru Tachici <alexandru.tachici@analog.com>
+
+
+Description
+-----------
+
+This driver supports hardware monitoring for Analog Devices ADM1266 sequencer.
+
+ADM1266 is a sequencer that features voltage readback from 17 channels via an
+integrated 12 bit SAR ADC, accessed using a PMBus interface.
+
+The driver is a client driver to the core PMBus driver. Please see
+Documentation/hwmon/pmbus for details on PMBus client drivers.
+
+
+Sysfs entries
+-------------
+
+The following attributes are supported. Limits are read-write, history reset
+attributes are write-only, all other attributes are read-only.
+
+inX_label		"voutx"
+inX_input		Measured voltage.
+inX_min			Minimum Voltage.
+inX_max			Maximum voltage.
+inX_min_alarm		Voltage low alarm.
+inX_max_alarm		Voltage high alarm.
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index 55ff4b7c5349..056f7107d7b8 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -30,6 +30,7 @@ Hardware Monitoring Kernel Drivers
    adm1026
    adm1031
    adm1177
+   adm1266
    adm1275
    adm9240
    ads7828
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index a337195b1c39..da34083e1ffd 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -26,6 +26,15 @@ config SENSORS_PMBUS
 	  This driver can also be built as a module. If so, the module will
 	  be called pmbus.
 
+config SENSORS_ADM1266
+	tristate "Analog Devices ADM1266 Sequencer"
+	help
+	  If you say yes here you get hardware monitoring support for Analog
+	  Devices ADM1266 Cascadable Super Sequencer.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called adm1266.
+
 config SENSORS_ADM1275
 	tristate "Analog Devices ADM1275 and compatibles"
 	help
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index c4b15db996ad..da41d22be1c9 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -5,6 +5,7 @@
 
 obj-$(CONFIG_PMBUS)		+= pmbus_core.o
 obj-$(CONFIG_SENSORS_PMBUS)	+= pmbus.o
+obj-$(CONFIG_SENSORS_ADM1266)	+= adm1266.o
 obj-$(CONFIG_SENSORS_ADM1275)	+= adm1275.o
 obj-$(CONFIG_SENSORS_BEL_PFE)	+= bel-pfe.o
 obj-$(CONFIG_SENSORS_IBM_CFFPS)	+= ibm-cffps.o
diff --git a/drivers/hwmon/pmbus/adm1266.c b/drivers/hwmon/pmbus/adm1266.c
new file mode 100644
index 000000000000..79e8d90886b8
--- /dev/null
+++ b/drivers/hwmon/pmbus/adm1266.c
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ADM1266 - Cascadable Super Sequencer with Margin
+ * Control and Fault Recording
+ *
+ * Copyright 2020 Analog Devices Inc.
+ */
+
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include "pmbus.h"
+#include <linux/slab.h>
+
+struct adm1266_data {
+	struct pmbus_driver_info info;
+	struct i2c_client *client;
+};
+
+static int adm1266_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+	struct adm1266_data *data;
+	int i;
+
+	data = devm_kzalloc(&client->dev, sizeof(struct adm1266_data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->client = client;
+	data->info.pages = 17;
+	data->info.format[PSC_VOLTAGE_OUT] = linear;
+	for (i = 0; i < data->info.pages; i++)
+		data->info.func[i] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT;
+
+	return pmbus_do_probe(client, id, &data->info);
+}
+
+static const struct of_device_id adm1266_of_match[] = {
+	{ .compatible = "adi,adm1266" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, adm1266_of_match);
+
+static const struct i2c_device_id adm1266_id[] = {
+	{ "adm1266", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, adm1266_id);
+
+static struct i2c_driver adm1266_driver = {
+	.driver = {
+		   .name = "adm1266",
+		   .of_match_table = adm1266_of_match,
+		  },
+	.probe = adm1266_probe,
+	.remove = pmbus_do_remove,
+	.id_table = adm1266_id,
+};
+
+module_i2c_driver(adm1266_driver);
+
+MODULE_AUTHOR("Alexandru Tachici <alexandru.tachici@analog.com>");
+MODULE_DESCRIPTION("PMBus driver for Analog Devices ADM1266");
+MODULE_LICENSE("GPL v2");
-- 
2.20.1


^ permalink raw reply related	[flat|nested] 9+ messages in thread

* [PATCH v8 2/6] hwmon: pmbus: adm1266: Add Block process call
  2020-08-12 14:20 [PATCH v8 0/6] hwmon: pmbus: adm1266: add support alexandru.tachici
  2020-08-12 14:20 ` [PATCH v8 1/6] " alexandru.tachici
@ 2020-08-12 14:20 ` alexandru.tachici
  2020-08-12 14:20 ` [PATCH v8 3/6] hwmon: pmbus: adm1266: Add support for GPIOs alexandru.tachici
                   ` (4 subsequent siblings)
  6 siblings, 0 replies; 9+ messages in thread
From: alexandru.tachici @ 2020-08-12 14:20 UTC (permalink / raw)
  To: linux-hwmon, linux-kernel, devicetree; +Cc: robh+dt, linux, Alexandru Tachici

From: Alexandru Tachici <alexandru.tachici@analog.com>

PmBus devices support Block Write-Block Read Process
Call described in SMBus specification v 2.0 with the
exception that Block writes and reads are permitted to
have up 255 data bytes instead of max 32 bytes (SMBus).

This patch adds Block WR process call support for ADM1266.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
---
 drivers/hwmon/pmbus/Kconfig   |  1 +
 drivers/hwmon/pmbus/adm1266.c | 78 +++++++++++++++++++++++++++++++++++
 2 files changed, 79 insertions(+)

diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index da34083e1ffd..c04068b665e6 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -28,6 +28,7 @@ config SENSORS_PMBUS
 
 config SENSORS_ADM1266
 	tristate "Analog Devices ADM1266 Sequencer"
+	select CRC8
 	help
 	  If you say yes here you get hardware monitoring support for Analog
 	  Devices ADM1266 Cascadable Super Sequencer.
diff --git a/drivers/hwmon/pmbus/adm1266.c b/drivers/hwmon/pmbus/adm1266.c
index 79e8d90886b8..9db1c317029b 100644
--- a/drivers/hwmon/pmbus/adm1266.c
+++ b/drivers/hwmon/pmbus/adm1266.c
@@ -6,6 +6,7 @@
  * Copyright 2020 Analog Devices Inc.
  */
 
+#include <linux/crc8.h>
 #include <linux/i2c.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
@@ -13,11 +14,85 @@
 #include "pmbus.h"
 #include <linux/slab.h>
 
+#define ADM1266_PMBUS_BLOCK_MAX		255
+
 struct adm1266_data {
 	struct pmbus_driver_info info;
 	struct i2c_client *client;
+	struct mutex buf_mutex;
+	u8 write_buf[ADM1266_PMBUS_BLOCK_MAX + 1] ____cacheline_aligned;
+	u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1] ____cacheline_aligned;
 };
 
+DECLARE_CRC8_TABLE(pmbus_crc_table);
+
+/*
+ * Different from Block Read as it sends data and waits for the slave to
+ * return a value dependent on that data. The protocol is simply a Write Block
+ * followed by a Read Block without the Read-Block command field and the
+ * Write-Block STOP bit.
+ */
+static int adm1266_pmbus_block_xfer(struct adm1266_data *data, u8 cmd, u8 w_len, u8 *data_w,
+				    u8 *data_r)
+{
+	struct i2c_client *client = data->client;
+	struct i2c_msg msgs[2] = {
+		{
+			.addr = client->addr,
+			.flags = I2C_M_DMA_SAFE,
+			.buf = data->write_buf,
+			.len = w_len + 2,
+		},
+		{
+			.addr = client->addr,
+			.flags = I2C_M_RD | I2C_M_DMA_SAFE,
+			.buf = data->read_buf,
+			.len = ADM1266_PMBUS_BLOCK_MAX + 2,
+		}
+	};
+	u8 addr;
+	u8 crc;
+	int ret;
+
+	mutex_lock(&data->buf_mutex);
+
+	msgs[0].buf[0] = cmd;
+	msgs[0].buf[1] = w_len;
+	memcpy(&msgs[0].buf[2], data_w, w_len);
+
+	ret = i2c_transfer(client->adapter, msgs, 2);
+	if (ret != 2) {
+		if (ret >= 0)
+			ret = -EPROTO;
+
+		mutex_unlock(&data->buf_mutex);
+
+		return ret;
+	}
+
+	if (client->flags & I2C_CLIENT_PEC) {
+		addr = i2c_8bit_addr_from_msg(&msgs[0]);
+		crc = crc8(pmbus_crc_table, &addr, 1, 0);
+		crc = crc8(pmbus_crc_table, msgs[0].buf,  msgs[0].len, crc);
+
+		addr = i2c_8bit_addr_from_msg(&msgs[1]);
+		crc = crc8(pmbus_crc_table, &addr, 1, crc);
+		crc = crc8(pmbus_crc_table, msgs[1].buf,  msgs[1].buf[0] + 1, crc);
+
+		if (crc != msgs[1].buf[msgs[1].buf[0] + 1]) {
+			mutex_unlock(&data->buf_mutex);
+			return -EBADMSG;
+		}
+	}
+
+	memcpy(data_r, &msgs[1].buf[1], msgs[1].buf[0]);
+
+	ret = msgs[1].buf[0];
+	mutex_unlock(&data->buf_mutex);
+
+	return ret;
+}
+
 static int adm1266_probe(struct i2c_client *client, const struct i2c_device_id *id)
 {
 	struct adm1266_data *data;
@@ -33,6 +108,9 @@ static int adm1266_probe(struct i2c_client *client, const struct i2c_device_id *
 	for (i = 0; i < data->info.pages; i++)
 		data->info.func[i] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT;
 
+	crc8_populate_msb(pmbus_crc_table, 0x7);
+	mutex_init(&data->buf_mutex);
+
 	return pmbus_do_probe(client, id, &data->info);
 }
 
-- 
2.20.1


^ permalink raw reply related	[flat|nested] 9+ messages in thread

* [PATCH v8 3/6] hwmon: pmbus: adm1266: Add support for GPIOs
  2020-08-12 14:20 [PATCH v8 0/6] hwmon: pmbus: adm1266: add support alexandru.tachici
  2020-08-12 14:20 ` [PATCH v8 1/6] " alexandru.tachici
  2020-08-12 14:20 ` [PATCH v8 2/6] hwmon: pmbus: adm1266: Add Block process call alexandru.tachici
@ 2020-08-12 14:20 ` alexandru.tachici
  2020-08-12 14:20 ` [PATCH v8 4/6] hwmon: pmbus: adm1266: add debugfs for states alexandru.tachici
                   ` (3 subsequent siblings)
  6 siblings, 0 replies; 9+ messages in thread
From: alexandru.tachici @ 2020-08-12 14:20 UTC (permalink / raw)
  To: linux-hwmon, linux-kernel, devicetree; +Cc: robh+dt, linux, Alexandru Tachici

From: Alexandru Tachici <alexandru.tachici@analog.com>

Adm1266 exposes 9 GPIOs and 16 PDIOs which are currently read-only. They
are controlled by the internal sequencing engine.

This patch makes adm1266 driver expose GPIOs and PDIOs to user-space
using GPIO provider kernel api.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
---
 drivers/hwmon/pmbus/Kconfig   |   1 +
 drivers/hwmon/pmbus/adm1266.c | 204 ++++++++++++++++++++++++++++++++++
 2 files changed, 205 insertions(+)

diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index c04068b665e6..2db3a93a43ea 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -29,6 +29,7 @@ config SENSORS_PMBUS
 config SENSORS_ADM1266
 	tristate "Analog Devices ADM1266 Sequencer"
 	select CRC8
+	depends on GPIOLIB
 	help
 	  If you say yes here you get hardware monitoring support for Analog
 	  Devices ADM1266 Cascadable Super Sequencer.
diff --git a/drivers/hwmon/pmbus/adm1266.c b/drivers/hwmon/pmbus/adm1266.c
index 9db1c317029b..7ca5aa751b7e 100644
--- a/drivers/hwmon/pmbus/adm1266.c
+++ b/drivers/hwmon/pmbus/adm1266.c
@@ -6,18 +6,42 @@
  * Copyright 2020 Analog Devices Inc.
  */
 
+#include <linux/bitfield.h>
 #include <linux/crc8.h>
+#include <linux/debugfs.h>
+#include <linux/gpio/driver.h>
 #include <linux/i2c.h>
+#include <linux/i2c-smbus.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include "pmbus.h"
 #include <linux/slab.h>
 
+#define ADM1266_PDIO_CONFIG	0xD4
+#define ADM1266_GPIO_CONFIG	0xE1
+#define ADM1266_PDIO_STATUS	0xE9
+#define ADM1266_GPIO_STATUS	0xEA
+
+/* ADM1266 GPIO defines */
+#define ADM1266_GPIO_NR			9
+#define ADM1266_GPIO_FUNCTIONS(x)	FIELD_GET(BIT(0), x)
+#define ADM1266_GPIO_INPUT_EN(x)	FIELD_GET(BIT(2), x)
+#define ADM1266_GPIO_OUTPUT_EN(x)	FIELD_GET(BIT(3), x)
+#define ADM1266_GPIO_OPEN_DRAIN(x)	FIELD_GET(BIT(4), x)
+
+/* ADM1266 PDIO defines */
+#define ADM1266_PDIO_NR			16
+#define ADM1266_PDIO_PIN_CFG(x)		FIELD_GET(GENMASK(15, 13), x)
+#define ADM1266_PDIO_GLITCH_FILT(x)	FIELD_GET(GENMASK(12, 9), x)
+#define ADM1266_PDIO_OUT_CFG(x)		FIELD_GET(GENMASK(2, 0), x)
+
 #define ADM1266_PMBUS_BLOCK_MAX		255
 
 struct adm1266_data {
 	struct pmbus_driver_info info;
+	struct gpio_chip gc;
+	const char *gpio_names[ADM1266_GPIO_NR + ADM1266_PDIO_NR];
 	struct i2c_client *client;
 	struct mutex buf_mutex;
 	u8 write_buf[ADM1266_PMBUS_BLOCK_MAX + 1] ____cacheline_aligned;
@@ -93,9 +117,185 @@ static int adm1266_pmbus_block_xfer(struct adm1266_data *data, u8 cmd, u8 w_len,
 	return ret;
 }
 
+static const unsigned int adm1266_gpio_mapping[ADM1266_GPIO_NR][2] = {
+	{1, 0},
+	{2, 1},
+	{3, 2},
+	{4, 8},
+	{5, 9},
+	{6, 10},
+	{7, 11},
+	{8, 6},
+	{9, 7},
+};
+
+static const char *adm1266_names[ADM1266_GPIO_NR + ADM1266_PDIO_NR] = {
+	"GPIO1", "GPIO2", "GPIO3", "GPIO4", "GPIO5", "GPIO6", "GPIO7", "GPIO8",
+	"GPIO9", "PDIO1", "PDIO2", "PDIO3", "PDIO4", "PDIO5", "PDIO6",
+	"PDIO7", "PDIO8", "PDIO9", "PDIO10", "PDIO11", "PDIO12", "PDIO13",
+	"PDIO14", "PDIO15", "PDIO16",
+};
+
+static int adm1266_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct adm1266_data *data = gpiochip_get_data(chip);
+	u8 read_buf[I2C_SMBUS_BLOCK_MAX + 1];
+	unsigned long pins_status;
+	unsigned int pmbus_cmd;
+	int ret;
+
+	if (offset < ADM1266_GPIO_NR)
+		pmbus_cmd = ADM1266_GPIO_STATUS;
+	else
+		pmbus_cmd = ADM1266_PDIO_STATUS;
+
+	ret = i2c_smbus_read_block_data(data->client, pmbus_cmd, read_buf);
+	if (ret < 0)
+		return ret;
+
+	pins_status = read_buf[0] + (read_buf[1] << 8);
+	if (offset < ADM1266_GPIO_NR)
+		return test_bit(adm1266_gpio_mapping[offset][1], &pins_status);
+
+	return test_bit(offset - ADM1266_GPIO_NR, &pins_status);
+}
+
+static int adm1266_gpio_get_multiple(struct gpio_chip *chip, unsigned long *mask,
+				     unsigned long *bits)
+{
+	struct adm1266_data *data = gpiochip_get_data(chip);
+	u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1];
+	unsigned long status;
+	unsigned int gpio_nr;
+	int ret;
+
+	ret = i2c_smbus_read_block_data(data->client, ADM1266_GPIO_STATUS, read_buf);
+	if (ret < 0)
+		return ret;
+
+	status = read_buf[0] + (read_buf[1] << 8);
+
+	*bits = 0;
+	for_each_set_bit(gpio_nr, mask, ADM1266_GPIO_NR) {
+		if (test_bit(adm1266_gpio_mapping[gpio_nr][1], &status))
+			set_bit(gpio_nr, bits);
+	}
+
+	ret = i2c_smbus_read_block_data(data->client, ADM1266_PDIO_STATUS, read_buf);
+	if (ret < 0)
+		return ret;
+
+	status = read_buf[0] + (read_buf[1] << 8);
+
+	*bits = 0;
+	for_each_set_bit_from(gpio_nr, mask, ADM1266_GPIO_NR + ADM1266_PDIO_STATUS) {
+		if (test_bit(gpio_nr - ADM1266_GPIO_NR, &status))
+			set_bit(gpio_nr, bits);
+	}
+
+	return 0;
+}
+
+static void adm1266_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+	struct adm1266_data *data = gpiochip_get_data(chip);
+	u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1];
+	unsigned long gpio_config;
+	unsigned long pdio_config;
+	unsigned long pin_cfg;
+	u8 write_cmd;
+	int ret;
+	int i;
+
+	for (i = 0; i < ADM1266_GPIO_NR; i++) {
+		write_cmd = adm1266_gpio_mapping[i][1];
+		ret = adm1266_pmbus_block_xfer(data, ADM1266_GPIO_CONFIG, 1, &write_cmd, read_buf);
+		if (ret != 2)
+			return;
+
+		gpio_config = read_buf[0];
+		seq_puts(s, adm1266_names[i]);
+
+		seq_puts(s, " ( ");
+		if (!ADM1266_GPIO_FUNCTIONS(gpio_config)) {
+			seq_puts(s, "high-Z )\n");
+			continue;
+		}
+		if (ADM1266_GPIO_INPUT_EN(gpio_config))
+			seq_puts(s, "input ");
+		if (ADM1266_GPIO_OUTPUT_EN(gpio_config))
+			seq_puts(s, "output ");
+		if (ADM1266_GPIO_OPEN_DRAIN(gpio_config))
+			seq_puts(s, "open-drain )\n");
+		else
+			seq_puts(s, "push-pull )\n");
+	}
+
+	write_cmd = 0xFF;
+	ret = adm1266_pmbus_block_xfer(data, ADM1266_PDIO_CONFIG, 1, &write_cmd, read_buf);
+	if (ret != 32)
+		return;
+
+	for (i = 0; i < ADM1266_PDIO_NR; i++) {
+		seq_puts(s, adm1266_names[ADM1266_GPIO_NR + i]);
+
+		pdio_config = read_buf[2 * i];
+		pdio_config += (read_buf[2 * i + 1] << 8);
+		pin_cfg = ADM1266_PDIO_PIN_CFG(pdio_config);
+
+		seq_puts(s, " ( ");
+		if (!pin_cfg || pin_cfg > 5) {
+			seq_puts(s, "high-Z )\n");
+			continue;
+		}
+
+		if (pin_cfg & BIT(0))
+			seq_puts(s, "output ");
+
+		if (pin_cfg & BIT(1))
+			seq_puts(s, "input ");
+
+		seq_puts(s, ")\n");
+	}
+}
+
+static int adm1266_config_gpio(struct adm1266_data *data)
+{
+	const char *name = dev_name(&data->client->dev);
+	char *gpio_name;
+	int ret;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(data->gpio_names); i++) {
+		gpio_name = devm_kasprintf(&data->client->dev, GFP_KERNEL, "adm1266-%x-%s",
+					   data->client->addr, adm1266_names[i]);
+		if (!gpio_name)
+			return -ENOMEM;
+
+		data->gpio_names[i] = gpio_name;
+	}
+
+	data->gc.label = name;
+	data->gc.parent = &data->client->dev;
+	data->gc.owner = THIS_MODULE;
+	data->gc.base = -1;
+	data->gc.names = data->gpio_names;
+	data->gc.ngpio = ARRAY_SIZE(data->gpio_names);
+	data->gc.get = adm1266_gpio_get;
+	data->gc.get_multiple = adm1266_gpio_get_multiple;
+	data->gc.dbg_show = adm1266_gpio_dbg_show;
+
+	ret = devm_gpiochip_add_data(&data->client->dev, &data->gc, data);
+	if (ret)
+		dev_err(&data->client->dev, "GPIO registering failed (%d)\n", ret);
+
+	return ret;
+}
+
 static int adm1266_probe(struct i2c_client *client, const struct i2c_device_id *id)
 {
 	struct adm1266_data *data;
+	int ret;
 	int i;
 
 	data = devm_kzalloc(&client->dev, sizeof(struct adm1266_data), GFP_KERNEL);
@@ -111,6 +311,10 @@ static int adm1266_probe(struct i2c_client *client, const struct i2c_device_id *
 	crc8_populate_msb(pmbus_crc_table, 0x7);
 	mutex_init(&data->buf_mutex);
 
+	ret = adm1266_config_gpio(data);
+	if (ret < 0)
+		return ret;
+
 	return pmbus_do_probe(client, id, &data->info);
 }
 
-- 
2.20.1


^ permalink raw reply related	[flat|nested] 9+ messages in thread

* [PATCH v8 4/6] hwmon: pmbus: adm1266: add debugfs for states
  2020-08-12 14:20 [PATCH v8 0/6] hwmon: pmbus: adm1266: add support alexandru.tachici
                   ` (2 preceding siblings ...)
  2020-08-12 14:20 ` [PATCH v8 3/6] hwmon: pmbus: adm1266: Add support for GPIOs alexandru.tachici
@ 2020-08-12 14:20 ` alexandru.tachici
  2020-08-12 14:20 ` [PATCH v8 5/6] hwmon: pmbus: adm1266: read blackbox alexandru.tachici
                   ` (2 subsequent siblings)
  6 siblings, 0 replies; 9+ messages in thread
From: alexandru.tachici @ 2020-08-12 14:20 UTC (permalink / raw)
  To: linux-hwmon, linux-kernel, devicetree; +Cc: robh+dt, linux, Alexandru Tachici

From: Alexandru Tachici <alexandru.tachici@analog.com>

Add a debugfs entry which prints the current state
of the adm1266 sequencer.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
---
 drivers/hwmon/pmbus/adm1266.c | 41 ++++++++++++++++++++++++++++++++++-
 1 file changed, 40 insertions(+), 1 deletion(-)

diff --git a/drivers/hwmon/pmbus/adm1266.c b/drivers/hwmon/pmbus/adm1266.c
index 7ca5aa751b7e..df7954e2ce9f 100644
--- a/drivers/hwmon/pmbus/adm1266.c
+++ b/drivers/hwmon/pmbus/adm1266.c
@@ -19,6 +19,7 @@
 #include <linux/slab.h>
 
 #define ADM1266_PDIO_CONFIG	0xD4
+#define ADM1266_READ_STATE	0xD9
 #define ADM1266_GPIO_CONFIG	0xE1
 #define ADM1266_PDIO_STATUS	0xE9
 #define ADM1266_GPIO_STATUS	0xEA
@@ -43,6 +44,7 @@ struct adm1266_data {
 	struct gpio_chip gc;
 	const char *gpio_names[ADM1266_GPIO_NR + ADM1266_PDIO_NR];
 	struct i2c_client *client;
+	struct dentry *debugfs_dir;
 	struct mutex buf_mutex;
 	u8 write_buf[ADM1266_PMBUS_BLOCK_MAX + 1] ____cacheline_aligned;
 	u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1] ____cacheline_aligned;
@@ -292,6 +294,37 @@ static int adm1266_config_gpio(struct adm1266_data *data)
 	return ret;
 }
 
+static int adm1266_state_read(struct seq_file *s, void *pdata)
+{
+	struct device *dev = s->private;
+	struct i2c_client *client = to_i2c_client(dev);
+	int ret;
+
+	ret = i2c_smbus_read_word_data(client, ADM1266_READ_STATE);
+	if (ret < 0)
+		return ret;
+
+	seq_printf(s, "%d\n", ret);
+
+	return 0;
+}
+
+static void adm1266_init_debugfs(struct adm1266_data *data)
+{
+	struct dentry *root;
+
+	root = pmbus_get_debugfs_dir(data->client);
+	if (!root)
+		return;
+
+	data->debugfs_dir = debugfs_create_dir(data->client->name, root);
+	if (!data->debugfs_dir)
+		return;
+
+	debugfs_create_devm_seqfile(&data->client->dev, "sequencer_state", data->debugfs_dir,
+				    adm1266_state_read);
+}
+
 static int adm1266_probe(struct i2c_client *client, const struct i2c_device_id *id)
 {
 	struct adm1266_data *data;
@@ -315,7 +348,13 @@ static int adm1266_probe(struct i2c_client *client, const struct i2c_device_id *
 	if (ret < 0)
 		return ret;
 
-	return pmbus_do_probe(client, id, &data->info);
+	ret = pmbus_do_probe(client, id, &data->info);
+	if (ret)
+		return ret;
+
+	adm1266_init_debugfs(data);
+
+	return 0;
 }
 
 static const struct of_device_id adm1266_of_match[] = {
-- 
2.20.1


^ permalink raw reply related	[flat|nested] 9+ messages in thread

* [PATCH v8 5/6] hwmon: pmbus: adm1266: read blackbox
  2020-08-12 14:20 [PATCH v8 0/6] hwmon: pmbus: adm1266: add support alexandru.tachici
                   ` (3 preceding siblings ...)
  2020-08-12 14:20 ` [PATCH v8 4/6] hwmon: pmbus: adm1266: add debugfs for states alexandru.tachici
@ 2020-08-12 14:20 ` alexandru.tachici
  2020-08-12 14:20 ` [PATCH v8 6/6] dt-bindings: hwmon: Add bindings for ADM1266 alexandru.tachici
  2020-08-22 16:21 ` [PATCH v8 0/6] hwmon: pmbus: adm1266: add support Guenter Roeck
  6 siblings, 0 replies; 9+ messages in thread
From: alexandru.tachici @ 2020-08-12 14:20 UTC (permalink / raw)
  To: linux-hwmon, linux-kernel, devicetree; +Cc: robh+dt, linux, Alexandru Tachici

From: Alexandru Tachici <alexandru.tachici@analog.com>

Use the nvmem kernel api to expose the black box
chip functionality to userspace.

Using this feature, the device is capable of recording
to nonvolatile flash memory the vital data about the
system status that caused the system to perform a
black box write.

A blackbox is 64 bytes of data containing all the
status registers, last two states of the sequencer,
timestamp and counters. The mapping of this data is
described in the adm1266 datasheet.

On power-up the driver sets the unix time to
the adm1266 using the SET_RTC command. This value
is incremented by an internal clock and it is used
as timestamp for the black box feature.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
---
 drivers/hwmon/pmbus/adm1266.c | 127 ++++++++++++++++++++++++++++++++++
 1 file changed, 127 insertions(+)

diff --git a/drivers/hwmon/pmbus/adm1266.c b/drivers/hwmon/pmbus/adm1266.c
index df7954e2ce9f..1d83c4f42eaf 100644
--- a/drivers/hwmon/pmbus/adm1266.c
+++ b/drivers/hwmon/pmbus/adm1266.c
@@ -15,12 +15,19 @@
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/nvmem-provider.h>
 #include "pmbus.h"
 #include <linux/slab.h>
+#include <linux/timekeeping.h>
 
+#define ADM1266_BLACKBOX_CONFIG	0xD3
 #define ADM1266_PDIO_CONFIG	0xD4
 #define ADM1266_READ_STATE	0xD9
+#define ADM1266_READ_BLACKBOX	0xDE
+#define ADM1266_SET_RTC		0xDF
 #define ADM1266_GPIO_CONFIG	0xE1
+#define ADM1266_BLACKBOX_INFO	0xE6
 #define ADM1266_PDIO_STATUS	0xE9
 #define ADM1266_GPIO_STATUS	0xEA
 
@@ -37,6 +44,9 @@
 #define ADM1266_PDIO_GLITCH_FILT(x)	FIELD_GET(GENMASK(12, 9), x)
 #define ADM1266_PDIO_OUT_CFG(x)		FIELD_GET(GENMASK(2, 0), x)
 
+#define ADM1266_BLACKBOX_OFFSET		0
+#define ADM1266_BLACKBOX_SIZE		64
+
 #define ADM1266_PMBUS_BLOCK_MAX		255
 
 struct adm1266_data {
@@ -45,11 +55,22 @@ struct adm1266_data {
 	const char *gpio_names[ADM1266_GPIO_NR + ADM1266_PDIO_NR];
 	struct i2c_client *client;
 	struct dentry *debugfs_dir;
+	struct nvmem_config nvmem_config;
+	struct nvmem_device *nvmem;
+	u8 *dev_mem;
 	struct mutex buf_mutex;
 	u8 write_buf[ADM1266_PMBUS_BLOCK_MAX + 1] ____cacheline_aligned;
 	u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1] ____cacheline_aligned;
 };
 
+static const struct nvmem_cell_info adm1266_nvmem_cells[] = {
+	{
+		.name           = "blackbox",
+		.offset         = ADM1266_BLACKBOX_OFFSET,
+		.bytes          = 2048,
+	},
+};
+
 DECLARE_CRC8_TABLE(pmbus_crc_table);
 
 /*
@@ -325,6 +346,104 @@ static void adm1266_init_debugfs(struct adm1266_data *data)
 				    adm1266_state_read);
 }
 
+static int adm1266_nvmem_read_blackbox(struct adm1266_data *data, u8 *read_buff)
+{
+	int record_count;
+	char index;
+	u8 buf[5];
+	int ret;
+
+	ret = i2c_smbus_read_block_data(data->client, ADM1266_BLACKBOX_INFO, buf);
+	if (ret < 0)
+		return ret;
+
+	if (ret != 4)
+		return -EIO;
+
+	record_count = buf[3];
+
+	for (index = 0; index < record_count; index++) {
+		ret = adm1266_pmbus_block_xfer(data, ADM1266_READ_BLACKBOX, 1, &index, read_buff);
+		if (ret < 0)
+			return ret;
+
+		if (ret != ADM1266_BLACKBOX_SIZE)
+			return -EIO;
+
+		read_buff += ADM1266_BLACKBOX_SIZE;
+	}
+
+	return 0;
+}
+
+static int adm1266_nvmem_read(void *priv, unsigned int offset, void *val, size_t bytes)
+{
+	struct adm1266_data *data = priv;
+	int ret;
+
+	if (offset + bytes > data->nvmem_config.size)
+		return -EINVAL;
+
+	if (offset == 0) {
+		memset(data->dev_mem, 0, data->nvmem_config.size);
+
+		ret = adm1266_nvmem_read_blackbox(data, data->dev_mem);
+		if (ret) {
+			dev_err(&data->client->dev, "Could not read blackbox!");
+			return ret;
+		}
+	}
+
+	memcpy(val, data->dev_mem + offset, bytes);
+
+	return 0;
+}
+
+static int adm1266_config_nvmem(struct adm1266_data *data)
+{
+	data->nvmem_config.name = dev_name(&data->client->dev);
+	data->nvmem_config.dev = &data->client->dev;
+	data->nvmem_config.root_only = true;
+	data->nvmem_config.read_only = true;
+	data->nvmem_config.owner = THIS_MODULE;
+	data->nvmem_config.reg_read = adm1266_nvmem_read;
+	data->nvmem_config.cells = adm1266_nvmem_cells;
+	data->nvmem_config.ncells = ARRAY_SIZE(adm1266_nvmem_cells);
+	data->nvmem_config.priv = data;
+	data->nvmem_config.stride = 1;
+	data->nvmem_config.word_size = 1;
+	data->nvmem_config.size = adm1266_nvmem_cells[0].bytes;
+
+	data->dev_mem = devm_kzalloc(&data->client->dev, data->nvmem_config.size, GFP_KERNEL);
+	if (!data->dev_mem)
+		return -ENOMEM;
+
+	data->nvmem = devm_nvmem_register(&data->client->dev, &data->nvmem_config);
+	if (IS_ERR(data->nvmem)) {
+		dev_err(&data->client->dev, "Could not register nvmem!");
+		return PTR_ERR(data->nvmem);
+	}
+
+	return 0;
+}
+
+static int adm1266_set_rtc(struct adm1266_data *data)
+{
+	time64_t kt;
+	char write_buf[6];
+	int i;
+
+	kt = ktime_get_seconds();
+
+	memset(write_buf, 0, sizeof(write_buf));
+
+	for (i = 0; i < 4; i++)
+		write_buf[2 + i] = (kt >> (i * 8)) & 0xFF;
+
+	return i2c_smbus_write_block_data(data->client, ADM1266_SET_RTC, sizeof(write_buf),
+					  write_buf);
+}
+
 static int adm1266_probe(struct i2c_client *client, const struct i2c_device_id *id)
 {
 	struct adm1266_data *data;
@@ -348,6 +467,14 @@ static int adm1266_probe(struct i2c_client *client, const struct i2c_device_id *
 	if (ret < 0)
 		return ret;
 
+	ret = adm1266_set_rtc(data);
+	if (ret < 0)
+		return ret;
+
+	ret = adm1266_config_nvmem(data);
+	if (ret < 0)
+		return ret;
+
 	ret = pmbus_do_probe(client, id, &data->info);
 	if (ret)
 		return ret;
-- 
2.20.1


^ permalink raw reply related	[flat|nested] 9+ messages in thread

* [PATCH v8 6/6] dt-bindings: hwmon: Add bindings for ADM1266
  2020-08-12 14:20 [PATCH v8 0/6] hwmon: pmbus: adm1266: add support alexandru.tachici
                   ` (4 preceding siblings ...)
  2020-08-12 14:20 ` [PATCH v8 5/6] hwmon: pmbus: adm1266: read blackbox alexandru.tachici
@ 2020-08-12 14:20 ` alexandru.tachici
  2020-08-12 16:44   ` Rob Herring
  2020-08-22 16:21 ` [PATCH v8 0/6] hwmon: pmbus: adm1266: add support Guenter Roeck
  6 siblings, 1 reply; 9+ messages in thread
From: alexandru.tachici @ 2020-08-12 14:20 UTC (permalink / raw)
  To: linux-hwmon, linux-kernel, devicetree; +Cc: robh+dt, linux, Alexandru Tachici

From: Alexandru Tachici <alexandru.tachici@analog.com>

Add bindings for the Analog Devices ADM1266 sequencer.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
---
 .../bindings/hwmon/adi,adm1266.yaml           | 51 +++++++++++++++++++
 1 file changed, 51 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/hwmon/adi,adm1266.yaml

diff --git a/Documentation/devicetree/bindings/hwmon/adi,adm1266.yaml b/Documentation/devicetree/bindings/hwmon/adi,adm1266.yaml
new file mode 100644
index 000000000000..43b4f4f57b49
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/adi,adm1266.yaml
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/adi,adm1266.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADM1266 Cascadable Super Sequencer with Margin
+  Control and Fault Recording
+
+maintainers:
+  - Alexandru Tachici <alexandru.tachici@analog.com>
+
+description: |
+  Analog Devices ADM1266 Cascadable Super Sequencer with Margin
+  Control and Fault Recording.
+  https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1266.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,adm1266
+
+  reg:
+    description: |
+      I2C address of slave device.
+    items:
+      minimum: 0x40
+      maximum: 0x4F
+
+  avcc-supply:
+    description: |
+      Phandle to the Avcc power supply.
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        adm1266@40 {
+                compatible = "adi,adm1266";
+                reg = <0x40>;
+        };
+    };
+...
-- 
2.20.1


^ permalink raw reply related	[flat|nested] 9+ messages in thread

* Re: [PATCH v8 6/6] dt-bindings: hwmon: Add bindings for ADM1266
  2020-08-12 14:20 ` [PATCH v8 6/6] dt-bindings: hwmon: Add bindings for ADM1266 alexandru.tachici
@ 2020-08-12 16:44   ` Rob Herring
  0 siblings, 0 replies; 9+ messages in thread
From: Rob Herring @ 2020-08-12 16:44 UTC (permalink / raw)
  To: alexandru.tachici; +Cc: devicetree, robh+dt, linux-hwmon, linux-kernel, linux

On Wed, 12 Aug 2020 17:20:55 +0300, alexandru.tachici@analog.com wrote:
> From: Alexandru Tachici <alexandru.tachici@analog.com>
> 
> Add bindings for the Analog Devices ADM1266 sequencer.
> 
> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
> ---
>  .../bindings/hwmon/adi,adm1266.yaml           | 51 +++++++++++++++++++
>  1 file changed, 51 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/hwmon/adi,adm1266.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH v8 0/6] hwmon: pmbus: adm1266: add support
  2020-08-12 14:20 [PATCH v8 0/6] hwmon: pmbus: adm1266: add support alexandru.tachici
                   ` (5 preceding siblings ...)
  2020-08-12 14:20 ` [PATCH v8 6/6] dt-bindings: hwmon: Add bindings for ADM1266 alexandru.tachici
@ 2020-08-22 16:21 ` Guenter Roeck
  6 siblings, 0 replies; 9+ messages in thread
From: Guenter Roeck @ 2020-08-22 16:21 UTC (permalink / raw)
  To: alexandru.tachici; +Cc: linux-hwmon, linux-kernel, devicetree, robh+dt

On Wed, Aug 12, 2020 at 05:20:49PM +0300, alexandru.tachici@analog.com wrote:
> From: Alexandru Tachici <alexandru.tachici@analog.com>
> 
> Add PMBus probing driver for the adm1266 Cascadable
> Super Sequencer with Margin Control and Fault Recording.
> Driver is using the pmbus_core, creating sysfs files
> under hwmon for inputs: vh1->vh4 and vp1->vp13.
> 

Series applied.

Thanks,
Guenter

^ permalink raw reply	[flat|nested] 9+ messages in thread

end of thread, other threads:[~2020-08-22 16:22 UTC | newest]

Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-08-12 14:20 [PATCH v8 0/6] hwmon: pmbus: adm1266: add support alexandru.tachici
2020-08-12 14:20 ` [PATCH v8 1/6] " alexandru.tachici
2020-08-12 14:20 ` [PATCH v8 2/6] hwmon: pmbus: adm1266: Add Block process call alexandru.tachici
2020-08-12 14:20 ` [PATCH v8 3/6] hwmon: pmbus: adm1266: Add support for GPIOs alexandru.tachici
2020-08-12 14:20 ` [PATCH v8 4/6] hwmon: pmbus: adm1266: add debugfs for states alexandru.tachici
2020-08-12 14:20 ` [PATCH v8 5/6] hwmon: pmbus: adm1266: read blackbox alexandru.tachici
2020-08-12 14:20 ` [PATCH v8 6/6] dt-bindings: hwmon: Add bindings for ADM1266 alexandru.tachici
2020-08-12 16:44   ` Rob Herring
2020-08-22 16:21 ` [PATCH v8 0/6] hwmon: pmbus: adm1266: add support Guenter Roeck

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.