* [PATCH v5 00/80] drm/vc4: Support BCM2711 Display Pipeline
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, devicetree, Kamal Dasu,
Philipp Zabel, Rob Herring, Stephen Boyd
Hi everyone,
Here's a (pretty long) series to introduce support in the VC4 DRM driver
for the display pipeline found in the BCM2711 (and thus the RaspberryPi 4).
The main differences are that there's two HDMI controllers and that there's
more pixelvalve now. Those pixelvalve come with a mux in the HVS that still
have only 3 FIFOs. Both of those differences are breaking a bunch of
expectations in the driver, so we first need a good bunch of cleanup and
reworks to introduce support for the new controllers.
Similarly, the HDMI controller has all its registers shuffled and split in
multiple controllers now, so we need a bunch of changes to support this as
well.
Only the HDMI support is enabled for now (even though the DPI and DSI
outputs have been tested too).
Let me know if you have any comments
Maxime
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: devicetree@vger.kernel.org
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Changes from v4:
- Rebased on top of next-20200828
- Collected the various tags
- Fixed some issues with 4k support and dual output (thanks Hoegeun!)
- Fixed typos in commit logs (thanks Dave!)
- Split the csc setup hook into its own patch again
- Added the CEC clock to the DT binding
- Fixed the DT binding example
- Reduced the number of calls to of_device_is_compatible in vc4_kms_load
- Added back the check for the state commit in our commit hook
Changes from v3:
- Rebased on top of next-20200708
- Added a name to the HDMI audio codec component
- Only disable the BCM2711 HDMI pixelvalves at boot
- Fixed an error in the HVS binding
- Fix a framebuffer size condition that was inverted
- Changed the channel allocation algorithm using Eric's suggestion
- Always write the muxing values instead of updating if needed
- Improved a bit the hvs_available_channels comment in the structure
- Change atomic_complete_commit code to use for_each_new_crtc_in_state
- Change the muxing code to take into account disparities between the
BCM2711 and previous SoCs.
- Only change the clock rate on BCM2711 during a modeset
- Fix a crash at atomic_disable
- Use clk_set_min_rate for the core clock too
- Add a few defines, and simplify the FIFO level stuff
- Reordered the patches according to Eric's reviews
- Fixed a regression with VID_CTL setting on RPI3
Changes from v2:
- Rebased on top of next-20200526
- Split the firmware clock series away
- Removed the stuck pixel (with all the subsequent pixels being shifted
by one
- Fixed the writeback issue too.
- Fix the dual output
- Fixed the return value of phy_get_cp_current
- Enhanced the comment on the reset delay
- Increase the max width and height
- Made a proper Kconfig option for the DVP clock driver
- Fixed the alsa card name collision
Changes from v1:
- Rebased on top of 5.7-rc1
- Run checkpatch
- Added audio support
- Fixed some HDMI timeouts
- Swiched to clk_hw_register_gate_parent_data
- Reorder Kconfig symbols in drivers/i2c/busses
- Make the firmware clocks a child of the firmware node
- Switch DVP clock driver to clk_hw interface
- constify raspberrypi_clk_data in raspberrypi_clock_property
- Don't mark firmware clocks as IGNORE_UNUSED
- Change from reset_ms to reset_us in reset-simple, and add a bit more
comments
- Remove generic clk patch to test if a NULL pointer is returned
- Removed misleading message in the is_prepared renaming patch commit
message
- Constify HDMI controller variants
- Fix a bug in the allocation size of the clk data array
- Added a mention in the DT binding conversion patches about the breakage
- Merged a few fixes from kbuild
- Fixed a few bisection and CEC build issues
- Collected Acked-by and Reviewed-by
- Change Dave email address to raspberrypi.com
Dave Stevenson (7):
drm/vc4: Add support for the BCM2711 HVS5
drm/vc4: plane: Change LBM alignment constraint on LBM
drm/vc4: plane: Optimize the LBM allocation size
drm/vc4: hdmi: Use reg-names to retrieve the HDMI audio registers
drm/vc4: hdmi: Reset audio infoframe on encoder_enable if previously streaming
drm/vc4: hdmi: Set the b-frame marker to the match ALSA's default.
drm/vc4: hdmi: Add audio-related callbacks
Hoegeun Kwon (1):
drm/vc4: hdmi: Add pixel BVB clock control
Maxime Ripard (72):
dt-bindings: display: Add support for the BCM2711 HVS
drm/vc4: hvs: Boost the core clock during modeset
drm/vc4: plane: Create more planes
drm/vc4: crtc: Deal with different number of pixel per clock
drm/vc4: crtc: Use a shared interrupt
drm/vc4: crtc: Move the cob allocation outside of bind
drm/vc4: crtc: Rename HVS channel to output
drm/vc4: crtc: Use local chan variable
drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable
drm/vc4: kms: Convert to for_each_new_crtc_state
drm/vc4: crtc: Assign output to channel automatically
drm/vc4: crtc: Add FIFO depth to vc4_crtc_data
drm/vc4: crtc: Add function to compute FIFO level bits
drm/vc4: crtc: Rename HDMI encoder type to HDMI0
drm/vc4: crtc: Add HDMI1 encoder type
drm/vc4: crtc: Disable color management for HVS5
drm/vc4: crtc: Turn pixelvalve reset into a function
drm/vc4: crtc: Move PV dump to config_pv
drm/vc4: crtc: Move HVS init and close to a function
drm/vc4: crtc: Move the HVS gamma LUT setup to our init function
drm/vc4: hvs: Make sure our channel is reset
drm/vc4: crtc: Remove mode_set_nofb
drm/vc4: crtc: Remove redundant pixelvalve reset
drm/vc4: crtc: Move HVS channel init before the PV initialisation
drm/vc4: encoder: Add finer-grained encoder callbacks
drm/vc4: crtc: Add a delay after disabling the PixelValve output
drm/vc4: crtc: Clear the PixelValve FIFO on disable
drm/vc4: crtc: Clear the PixelValve FIFO during configuration
drm/vc4: hvs: Make the stop_channel function public
drm/vc4: hvs: Introduce a function to get the assigned FIFO
drm/vc4: crtc: Move the CRTC disable out
drm/vc4: drv: Disable the CRTC at boot time
dt-bindings: display: vc4: pv: Add BCM2711 pixel valves
drm/vc4: crtc: Add BCM2711 pixelvalves
drm/vc4: hdmi: Use debugfs private field
drm/vc4: hdmi: Move structure to header
drm/vc4: hdmi: rework connectors and encoders
drm/vc4: hdmi: Remove DDC argument to connector_init
drm/vc4: hdmi: Rename hdmi to vc4_hdmi
drm/vc4: hdmi: Move accessors to vc4_hdmi
drm/vc4: hdmi: Use local vc4_hdmi directly
drm/vc4: hdmi: Add container_of macros for encoders and connectors
drm/vc4: hdmi: Pass vc4_hdmi to CEC code
drm/vc4: hdmi: Retrieve the vc4_hdmi at unbind using our device
drm/vc4: hdmi: Remove vc4_dev hdmi pointer
drm/vc4: hdmi: Remove vc4_hdmi_connector
drm/vc4: hdmi: Introduce resource init and variant
drm/vc4: hdmi: Implement a register layout abstraction
drm/vc4: hdmi: Add reset callback
drm/vc4: hdmi: Add PHY init and disable function
drm/vc4: hdmi: Add PHY RNG enable / disable function
drm/vc4: hdmi: Add a CSC setup callback
drm/vc4: hdmi: Add a set_timings callback
drm/vc4: hdmi: Store the encoder type in the variant structure
drm/vc4: hdmi: Deal with multiple debugfs files
drm/vc4: hdmi: Move CEC init to its own function
drm/vc4: hdmi: Add CEC support flag
drm/vc4: hdmi: Remove unused CEC_CLOCK_DIV define
drm/vc4: hdmi: Rename drm_encoder pointer in mode_valid
drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate
drm/vc4: hdmi: Use clk_set_min_rate instead
drm/vc4: hdmi: Deal with multiple ALSA cards
drm/vc4: hdmi: Remove register dumps in enable
drm/vc4: hdmi: Always recenter the HDMI FIFO
drm/vc4: hdmi: Implement finer-grained hooks
drm/vc4: hdmi: Do the VID_CTL configuration at once
drm/vc4: hdmi: Switch to blank pixels when disabled
drm/vc4: hdmi: Support the BCM2711 HDMI controllers
dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings
dt-bindings: display: vc4: Document BCM2711 VC5
drm/vc4: drv: Support BCM2711
ARM: dts: bcm2711: Enable the display pipeline
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 117 +++++-
Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 +-
Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +-
Documentation/devicetree/bindings/display/brcm,bcm2835-vc4.yaml | 1 +-
arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 48 ++-
arch/arm/boot/dts/bcm2711.dtsi | 122 ++++-
drivers/gpu/drm/vc4/Makefile | 1 +-
drivers/gpu/drm/vc4/vc4_crtc.c | 354 +++++++++++----
drivers/gpu/drm/vc4/vc4_drv.c | 5 +-
drivers/gpu/drm/vc4/vc4_drv.h | 43 +-
drivers/gpu/drm/vc4/vc4_hdmi.c | 1650 +++++++++++++++++++++++++++++++++++++++++++-----------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 184 ++++++++-
drivers/gpu/drm/vc4/vc4_hdmi_phy.c | 520 +++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 442 +++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_hvs.c | 269 +++++++-----
drivers/gpu/drm/vc4/vc4_kms.c | 229 +++++++++-
drivers/gpu/drm/vc4/vc4_plane.c | 222 +++++++---
drivers/gpu/drm/vc4/vc4_regs.h | 177 +++-----
drivers/gpu/drm/vc4/vc4_txp.c | 4 +-
19 files changed, 3406 insertions(+), 1005 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_phy.c
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_regs.h
base-commit: 20c0f70ad7bf5aaf2e22ef974867d0708373fe93
--
git-series 0.9.1
^ permalink raw reply [flat|nested] 342+ messages in thread
* [PATCH v5 00/80] drm/vc4: Support BCM2711 Display Pipeline
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: devicetree, Tim Gover, Dave Stevenson, Stephen Boyd, Kamal Dasu,
linux-kernel, dri-devel, Rob Herring, bcm-kernel-feedback-list,
linux-rpi-kernel, Philipp Zabel, Phil Elwell, linux-arm-kernel,
Maxime Ripard
Hi everyone,
Here's a (pretty long) series to introduce support in the VC4 DRM driver
for the display pipeline found in the BCM2711 (and thus the RaspberryPi 4).
The main differences are that there's two HDMI controllers and that there's
more pixelvalve now. Those pixelvalve come with a mux in the HVS that still
have only 3 FIFOs. Both of those differences are breaking a bunch of
expectations in the driver, so we first need a good bunch of cleanup and
reworks to introduce support for the new controllers.
Similarly, the HDMI controller has all its registers shuffled and split in
multiple controllers now, so we need a bunch of changes to support this as
well.
Only the HDMI support is enabled for now (even though the DPI and DSI
outputs have been tested too).
Let me know if you have any comments
Maxime
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: devicetree@vger.kernel.org
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Changes from v4:
- Rebased on top of next-20200828
- Collected the various tags
- Fixed some issues with 4k support and dual output (thanks Hoegeun!)
- Fixed typos in commit logs (thanks Dave!)
- Split the csc setup hook into its own patch again
- Added the CEC clock to the DT binding
- Fixed the DT binding example
- Reduced the number of calls to of_device_is_compatible in vc4_kms_load
- Added back the check for the state commit in our commit hook
Changes from v3:
- Rebased on top of next-20200708
- Added a name to the HDMI audio codec component
- Only disable the BCM2711 HDMI pixelvalves at boot
- Fixed an error in the HVS binding
- Fix a framebuffer size condition that was inverted
- Changed the channel allocation algorithm using Eric's suggestion
- Always write the muxing values instead of updating if needed
- Improved a bit the hvs_available_channels comment in the structure
- Change atomic_complete_commit code to use for_each_new_crtc_in_state
- Change the muxing code to take into account disparities between the
BCM2711 and previous SoCs.
- Only change the clock rate on BCM2711 during a modeset
- Fix a crash at atomic_disable
- Use clk_set_min_rate for the core clock too
- Add a few defines, and simplify the FIFO level stuff
- Reordered the patches according to Eric's reviews
- Fixed a regression with VID_CTL setting on RPI3
Changes from v2:
- Rebased on top of next-20200526
- Split the firmware clock series away
- Removed the stuck pixel (with all the subsequent pixels being shifted
by one
- Fixed the writeback issue too.
- Fix the dual output
- Fixed the return value of phy_get_cp_current
- Enhanced the comment on the reset delay
- Increase the max width and height
- Made a proper Kconfig option for the DVP clock driver
- Fixed the alsa card name collision
Changes from v1:
- Rebased on top of 5.7-rc1
- Run checkpatch
- Added audio support
- Fixed some HDMI timeouts
- Swiched to clk_hw_register_gate_parent_data
- Reorder Kconfig symbols in drivers/i2c/busses
- Make the firmware clocks a child of the firmware node
- Switch DVP clock driver to clk_hw interface
- constify raspberrypi_clk_data in raspberrypi_clock_property
- Don't mark firmware clocks as IGNORE_UNUSED
- Change from reset_ms to reset_us in reset-simple, and add a bit more
comments
- Remove generic clk patch to test if a NULL pointer is returned
- Removed misleading message in the is_prepared renaming patch commit
message
- Constify HDMI controller variants
- Fix a bug in the allocation size of the clk data array
- Added a mention in the DT binding conversion patches about the breakage
- Merged a few fixes from kbuild
- Fixed a few bisection and CEC build issues
- Collected Acked-by and Reviewed-by
- Change Dave email address to raspberrypi.com
Dave Stevenson (7):
drm/vc4: Add support for the BCM2711 HVS5
drm/vc4: plane: Change LBM alignment constraint on LBM
drm/vc4: plane: Optimize the LBM allocation size
drm/vc4: hdmi: Use reg-names to retrieve the HDMI audio registers
drm/vc4: hdmi: Reset audio infoframe on encoder_enable if previously streaming
drm/vc4: hdmi: Set the b-frame marker to the match ALSA's default.
drm/vc4: hdmi: Add audio-related callbacks
Hoegeun Kwon (1):
drm/vc4: hdmi: Add pixel BVB clock control
Maxime Ripard (72):
dt-bindings: display: Add support for the BCM2711 HVS
drm/vc4: hvs: Boost the core clock during modeset
drm/vc4: plane: Create more planes
drm/vc4: crtc: Deal with different number of pixel per clock
drm/vc4: crtc: Use a shared interrupt
drm/vc4: crtc: Move the cob allocation outside of bind
drm/vc4: crtc: Rename HVS channel to output
drm/vc4: crtc: Use local chan variable
drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable
drm/vc4: kms: Convert to for_each_new_crtc_state
drm/vc4: crtc: Assign output to channel automatically
drm/vc4: crtc: Add FIFO depth to vc4_crtc_data
drm/vc4: crtc: Add function to compute FIFO level bits
drm/vc4: crtc: Rename HDMI encoder type to HDMI0
drm/vc4: crtc: Add HDMI1 encoder type
drm/vc4: crtc: Disable color management for HVS5
drm/vc4: crtc: Turn pixelvalve reset into a function
drm/vc4: crtc: Move PV dump to config_pv
drm/vc4: crtc: Move HVS init and close to a function
drm/vc4: crtc: Move the HVS gamma LUT setup to our init function
drm/vc4: hvs: Make sure our channel is reset
drm/vc4: crtc: Remove mode_set_nofb
drm/vc4: crtc: Remove redundant pixelvalve reset
drm/vc4: crtc: Move HVS channel init before the PV initialisation
drm/vc4: encoder: Add finer-grained encoder callbacks
drm/vc4: crtc: Add a delay after disabling the PixelValve output
drm/vc4: crtc: Clear the PixelValve FIFO on disable
drm/vc4: crtc: Clear the PixelValve FIFO during configuration
drm/vc4: hvs: Make the stop_channel function public
drm/vc4: hvs: Introduce a function to get the assigned FIFO
drm/vc4: crtc: Move the CRTC disable out
drm/vc4: drv: Disable the CRTC at boot time
dt-bindings: display: vc4: pv: Add BCM2711 pixel valves
drm/vc4: crtc: Add BCM2711 pixelvalves
drm/vc4: hdmi: Use debugfs private field
drm/vc4: hdmi: Move structure to header
drm/vc4: hdmi: rework connectors and encoders
drm/vc4: hdmi: Remove DDC argument to connector_init
drm/vc4: hdmi: Rename hdmi to vc4_hdmi
drm/vc4: hdmi: Move accessors to vc4_hdmi
drm/vc4: hdmi: Use local vc4_hdmi directly
drm/vc4: hdmi: Add container_of macros for encoders and connectors
drm/vc4: hdmi: Pass vc4_hdmi to CEC code
drm/vc4: hdmi: Retrieve the vc4_hdmi at unbind using our device
drm/vc4: hdmi: Remove vc4_dev hdmi pointer
drm/vc4: hdmi: Remove vc4_hdmi_connector
drm/vc4: hdmi: Introduce resource init and variant
drm/vc4: hdmi: Implement a register layout abstraction
drm/vc4: hdmi: Add reset callback
drm/vc4: hdmi: Add PHY init and disable function
drm/vc4: hdmi: Add PHY RNG enable / disable function
drm/vc4: hdmi: Add a CSC setup callback
drm/vc4: hdmi: Add a set_timings callback
drm/vc4: hdmi: Store the encoder type in the variant structure
drm/vc4: hdmi: Deal with multiple debugfs files
drm/vc4: hdmi: Move CEC init to its own function
drm/vc4: hdmi: Add CEC support flag
drm/vc4: hdmi: Remove unused CEC_CLOCK_DIV define
drm/vc4: hdmi: Rename drm_encoder pointer in mode_valid
drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate
drm/vc4: hdmi: Use clk_set_min_rate instead
drm/vc4: hdmi: Deal with multiple ALSA cards
drm/vc4: hdmi: Remove register dumps in enable
drm/vc4: hdmi: Always recenter the HDMI FIFO
drm/vc4: hdmi: Implement finer-grained hooks
drm/vc4: hdmi: Do the VID_CTL configuration at once
drm/vc4: hdmi: Switch to blank pixels when disabled
drm/vc4: hdmi: Support the BCM2711 HDMI controllers
dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings
dt-bindings: display: vc4: Document BCM2711 VC5
drm/vc4: drv: Support BCM2711
ARM: dts: bcm2711: Enable the display pipeline
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 117 +++++-
Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 +-
Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +-
Documentation/devicetree/bindings/display/brcm,bcm2835-vc4.yaml | 1 +-
arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 48 ++-
arch/arm/boot/dts/bcm2711.dtsi | 122 ++++-
drivers/gpu/drm/vc4/Makefile | 1 +-
drivers/gpu/drm/vc4/vc4_crtc.c | 354 +++++++++++----
drivers/gpu/drm/vc4/vc4_drv.c | 5 +-
drivers/gpu/drm/vc4/vc4_drv.h | 43 +-
drivers/gpu/drm/vc4/vc4_hdmi.c | 1650 +++++++++++++++++++++++++++++++++++++++++++-----------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 184 ++++++++-
drivers/gpu/drm/vc4/vc4_hdmi_phy.c | 520 +++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 442 +++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_hvs.c | 269 +++++++-----
drivers/gpu/drm/vc4/vc4_kms.c | 229 +++++++++-
drivers/gpu/drm/vc4/vc4_plane.c | 222 +++++++---
drivers/gpu/drm/vc4/vc4_regs.h | 177 +++-----
drivers/gpu/drm/vc4/vc4_txp.c | 4 +-
19 files changed, 3406 insertions(+), 1005 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_phy.c
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_regs.h
base-commit: 20c0f70ad7bf5aaf2e22ef974867d0708373fe93
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 342+ messages in thread
* [PATCH v5 00/80] drm/vc4: Support BCM2711 Display Pipeline
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: devicetree, Tim Gover, Dave Stevenson, Stephen Boyd, Kamal Dasu,
linux-kernel, dri-devel, Rob Herring, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Hi everyone,
Here's a (pretty long) series to introduce support in the VC4 DRM driver
for the display pipeline found in the BCM2711 (and thus the RaspberryPi 4).
The main differences are that there's two HDMI controllers and that there's
more pixelvalve now. Those pixelvalve come with a mux in the HVS that still
have only 3 FIFOs. Both of those differences are breaking a bunch of
expectations in the driver, so we first need a good bunch of cleanup and
reworks to introduce support for the new controllers.
Similarly, the HDMI controller has all its registers shuffled and split in
multiple controllers now, so we need a bunch of changes to support this as
well.
Only the HDMI support is enabled for now (even though the DPI and DSI
outputs have been tested too).
Let me know if you have any comments
Maxime
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: devicetree@vger.kernel.org
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Changes from v4:
- Rebased on top of next-20200828
- Collected the various tags
- Fixed some issues with 4k support and dual output (thanks Hoegeun!)
- Fixed typos in commit logs (thanks Dave!)
- Split the csc setup hook into its own patch again
- Added the CEC clock to the DT binding
- Fixed the DT binding example
- Reduced the number of calls to of_device_is_compatible in vc4_kms_load
- Added back the check for the state commit in our commit hook
Changes from v3:
- Rebased on top of next-20200708
- Added a name to the HDMI audio codec component
- Only disable the BCM2711 HDMI pixelvalves at boot
- Fixed an error in the HVS binding
- Fix a framebuffer size condition that was inverted
- Changed the channel allocation algorithm using Eric's suggestion
- Always write the muxing values instead of updating if needed
- Improved a bit the hvs_available_channels comment in the structure
- Change atomic_complete_commit code to use for_each_new_crtc_in_state
- Change the muxing code to take into account disparities between the
BCM2711 and previous SoCs.
- Only change the clock rate on BCM2711 during a modeset
- Fix a crash at atomic_disable
- Use clk_set_min_rate for the core clock too
- Add a few defines, and simplify the FIFO level stuff
- Reordered the patches according to Eric's reviews
- Fixed a regression with VID_CTL setting on RPI3
Changes from v2:
- Rebased on top of next-20200526
- Split the firmware clock series away
- Removed the stuck pixel (with all the subsequent pixels being shifted
by one
- Fixed the writeback issue too.
- Fix the dual output
- Fixed the return value of phy_get_cp_current
- Enhanced the comment on the reset delay
- Increase the max width and height
- Made a proper Kconfig option for the DVP clock driver
- Fixed the alsa card name collision
Changes from v1:
- Rebased on top of 5.7-rc1
- Run checkpatch
- Added audio support
- Fixed some HDMI timeouts
- Swiched to clk_hw_register_gate_parent_data
- Reorder Kconfig symbols in drivers/i2c/busses
- Make the firmware clocks a child of the firmware node
- Switch DVP clock driver to clk_hw interface
- constify raspberrypi_clk_data in raspberrypi_clock_property
- Don't mark firmware clocks as IGNORE_UNUSED
- Change from reset_ms to reset_us in reset-simple, and add a bit more
comments
- Remove generic clk patch to test if a NULL pointer is returned
- Removed misleading message in the is_prepared renaming patch commit
message
- Constify HDMI controller variants
- Fix a bug in the allocation size of the clk data array
- Added a mention in the DT binding conversion patches about the breakage
- Merged a few fixes from kbuild
- Fixed a few bisection and CEC build issues
- Collected Acked-by and Reviewed-by
- Change Dave email address to raspberrypi.com
Dave Stevenson (7):
drm/vc4: Add support for the BCM2711 HVS5
drm/vc4: plane: Change LBM alignment constraint on LBM
drm/vc4: plane: Optimize the LBM allocation size
drm/vc4: hdmi: Use reg-names to retrieve the HDMI audio registers
drm/vc4: hdmi: Reset audio infoframe on encoder_enable if previously streaming
drm/vc4: hdmi: Set the b-frame marker to the match ALSA's default.
drm/vc4: hdmi: Add audio-related callbacks
Hoegeun Kwon (1):
drm/vc4: hdmi: Add pixel BVB clock control
Maxime Ripard (72):
dt-bindings: display: Add support for the BCM2711 HVS
drm/vc4: hvs: Boost the core clock during modeset
drm/vc4: plane: Create more planes
drm/vc4: crtc: Deal with different number of pixel per clock
drm/vc4: crtc: Use a shared interrupt
drm/vc4: crtc: Move the cob allocation outside of bind
drm/vc4: crtc: Rename HVS channel to output
drm/vc4: crtc: Use local chan variable
drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable
drm/vc4: kms: Convert to for_each_new_crtc_state
drm/vc4: crtc: Assign output to channel automatically
drm/vc4: crtc: Add FIFO depth to vc4_crtc_data
drm/vc4: crtc: Add function to compute FIFO level bits
drm/vc4: crtc: Rename HDMI encoder type to HDMI0
drm/vc4: crtc: Add HDMI1 encoder type
drm/vc4: crtc: Disable color management for HVS5
drm/vc4: crtc: Turn pixelvalve reset into a function
drm/vc4: crtc: Move PV dump to config_pv
drm/vc4: crtc: Move HVS init and close to a function
drm/vc4: crtc: Move the HVS gamma LUT setup to our init function
drm/vc4: hvs: Make sure our channel is reset
drm/vc4: crtc: Remove mode_set_nofb
drm/vc4: crtc: Remove redundant pixelvalve reset
drm/vc4: crtc: Move HVS channel init before the PV initialisation
drm/vc4: encoder: Add finer-grained encoder callbacks
drm/vc4: crtc: Add a delay after disabling the PixelValve output
drm/vc4: crtc: Clear the PixelValve FIFO on disable
drm/vc4: crtc: Clear the PixelValve FIFO during configuration
drm/vc4: hvs: Make the stop_channel function public
drm/vc4: hvs: Introduce a function to get the assigned FIFO
drm/vc4: crtc: Move the CRTC disable out
drm/vc4: drv: Disable the CRTC at boot time
dt-bindings: display: vc4: pv: Add BCM2711 pixel valves
drm/vc4: crtc: Add BCM2711 pixelvalves
drm/vc4: hdmi: Use debugfs private field
drm/vc4: hdmi: Move structure to header
drm/vc4: hdmi: rework connectors and encoders
drm/vc4: hdmi: Remove DDC argument to connector_init
drm/vc4: hdmi: Rename hdmi to vc4_hdmi
drm/vc4: hdmi: Move accessors to vc4_hdmi
drm/vc4: hdmi: Use local vc4_hdmi directly
drm/vc4: hdmi: Add container_of macros for encoders and connectors
drm/vc4: hdmi: Pass vc4_hdmi to CEC code
drm/vc4: hdmi: Retrieve the vc4_hdmi at unbind using our device
drm/vc4: hdmi: Remove vc4_dev hdmi pointer
drm/vc4: hdmi: Remove vc4_hdmi_connector
drm/vc4: hdmi: Introduce resource init and variant
drm/vc4: hdmi: Implement a register layout abstraction
drm/vc4: hdmi: Add reset callback
drm/vc4: hdmi: Add PHY init and disable function
drm/vc4: hdmi: Add PHY RNG enable / disable function
drm/vc4: hdmi: Add a CSC setup callback
drm/vc4: hdmi: Add a set_timings callback
drm/vc4: hdmi: Store the encoder type in the variant structure
drm/vc4: hdmi: Deal with multiple debugfs files
drm/vc4: hdmi: Move CEC init to its own function
drm/vc4: hdmi: Add CEC support flag
drm/vc4: hdmi: Remove unused CEC_CLOCK_DIV define
drm/vc4: hdmi: Rename drm_encoder pointer in mode_valid
drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate
drm/vc4: hdmi: Use clk_set_min_rate instead
drm/vc4: hdmi: Deal with multiple ALSA cards
drm/vc4: hdmi: Remove register dumps in enable
drm/vc4: hdmi: Always recenter the HDMI FIFO
drm/vc4: hdmi: Implement finer-grained hooks
drm/vc4: hdmi: Do the VID_CTL configuration at once
drm/vc4: hdmi: Switch to blank pixels when disabled
drm/vc4: hdmi: Support the BCM2711 HDMI controllers
dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings
dt-bindings: display: vc4: Document BCM2711 VC5
drm/vc4: drv: Support BCM2711
ARM: dts: bcm2711: Enable the display pipeline
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 117 +++++-
Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 +-
Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +-
Documentation/devicetree/bindings/display/brcm,bcm2835-vc4.yaml | 1 +-
arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 48 ++-
arch/arm/boot/dts/bcm2711.dtsi | 122 ++++-
drivers/gpu/drm/vc4/Makefile | 1 +-
drivers/gpu/drm/vc4/vc4_crtc.c | 354 +++++++++++----
drivers/gpu/drm/vc4/vc4_drv.c | 5 +-
drivers/gpu/drm/vc4/vc4_drv.h | 43 +-
drivers/gpu/drm/vc4/vc4_hdmi.c | 1650 +++++++++++++++++++++++++++++++++++++++++++-----------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 184 ++++++++-
drivers/gpu/drm/vc4/vc4_hdmi_phy.c | 520 +++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 442 +++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_hvs.c | 269 +++++++-----
drivers/gpu/drm/vc4/vc4_kms.c | 229 +++++++++-
drivers/gpu/drm/vc4/vc4_plane.c | 222 +++++++---
drivers/gpu/drm/vc4/vc4_regs.h | 177 +++-----
drivers/gpu/drm/vc4/vc4_txp.c | 4 +-
19 files changed, 3406 insertions(+), 1005 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_phy.c
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_regs.h
base-commit: 20c0f70ad7bf5aaf2e22ef974867d0708373fe93
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 342+ messages in thread
* [PATCH v5 01/80] dt-bindings: display: Add support for the BCM2711 HVS
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The HVS found in the BCM2711 is slightly different from the previous
generations, let's add a compatible for it.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 ++++++-
1 file changed, 17 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml
index 02410f8d6d49..e826ab0adb75 100644
--- a/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml
+++ b/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml
@@ -11,7 +11,9 @@ maintainers:
properties:
compatible:
- const: brcm,bcm2835-hvs
+ enum:
+ - brcm,bcm2711-hvs
+ - brcm,bcm2835-hvs
reg:
maxItems: 1
@@ -19,6 +21,10 @@ properties:
interrupts:
maxItems: 1
+ clocks:
+ maxItems: 1
+ description: Core Clock
+
required:
- compatible
- reg
@@ -26,6 +32,16 @@ required:
additionalProperties: false
+if:
+ properties:
+ compatible:
+ contains:
+ const: brcm,bcm2711-hvs"
+
+then:
+ required:
+ - clocks
+
examples:
- |
hvs@7e400000 {
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 01/80] dt-bindings: display: Add support for the BCM2711 HVS
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The HVS found in the BCM2711 is slightly different from the previous
generations, let's add a compatible for it.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 ++++++-
1 file changed, 17 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml
index 02410f8d6d49..e826ab0adb75 100644
--- a/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml
+++ b/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml
@@ -11,7 +11,9 @@ maintainers:
properties:
compatible:
- const: brcm,bcm2835-hvs
+ enum:
+ - brcm,bcm2711-hvs
+ - brcm,bcm2835-hvs
reg:
maxItems: 1
@@ -19,6 +21,10 @@ properties:
interrupts:
maxItems: 1
+ clocks:
+ maxItems: 1
+ description: Core Clock
+
required:
- compatible
- reg
@@ -26,6 +32,16 @@ required:
additionalProperties: false
+if:
+ properties:
+ compatible:
+ contains:
+ const: brcm,bcm2711-hvs"
+
+then:
+ required:
+ - clocks
+
examples:
- |
hvs@7e400000 {
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 01/80] dt-bindings: display: Add support for the BCM2711 HVS
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The HVS found in the BCM2711 is slightly different from the previous
generations, let's add a compatible for it.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 ++++++-
1 file changed, 17 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml
index 02410f8d6d49..e826ab0adb75 100644
--- a/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml
+++ b/Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml
@@ -11,7 +11,9 @@ maintainers:
properties:
compatible:
- const: brcm,bcm2835-hvs
+ enum:
+ - brcm,bcm2711-hvs
+ - brcm,bcm2835-hvs
reg:
maxItems: 1
@@ -19,6 +21,10 @@ properties:
interrupts:
maxItems: 1
+ clocks:
+ maxItems: 1
+ description: Core Clock
+
required:
- compatible
- reg
@@ -26,6 +32,16 @@ required:
additionalProperties: false
+if:
+ properties:
+ compatible:
+ contains:
+ const: brcm,bcm2711-hvs"
+
+then:
+ required:
+ - clocks
+
examples:
- |
hvs@7e400000 {
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 02/80] drm/vc4: Add support for the BCM2711 HVS5
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HVS found in the BCM2711 is slightly different from the previous
generations.
Most notably, the display list layout changes a bit, the LBM doesn't have
the same size and the formats ordering for some formats is swapped.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 4 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 34 ++++--
drivers/gpu/drm/vc4/vc4_plane.c | 194 ++++++++++++++++++++++++---------
drivers/gpu/drm/vc4/vc4_regs.h | 67 +++++++++++-
4 files changed, 240 insertions(+), 59 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index fa19160c801f..e4cde1f9224b 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -329,7 +329,11 @@ struct vc4_hvs {
spinlock_t mm_lock;
struct drm_mm_node mitchell_netravali_filter;
+
struct debugfs_regset32 regset;
+
+ /* HVS version 5 flag, therefore requires updated dlist structures */
+ bool hvs5;
};
struct vc4_plane {
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 2d2bf59c0503..836d8799d79e 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -277,11 +277,19 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
* mode.
*/
dispctrl = SCALER_DISPCTRLX_ENABLE;
- dispctrl |= VC4_SET_FIELD(mode->hdisplay,
- SCALER_DISPCTRLX_WIDTH) |
- VC4_SET_FIELD(mode->vdisplay,
- SCALER_DISPCTRLX_HEIGHT) |
- (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
+
+ if (!vc4->hvs->hvs5)
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
+ else
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER5_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER5_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
HVS_WRITE(SCALER_DISPCTRLX(vc4_crtc->channel), dispctrl);
}
@@ -521,6 +529,9 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
hvs->pdev = pdev;
+ if (of_device_is_compatible(pdev->dev.of_node, "brcm,bcm2711-hvs"))
+ hvs->hvs5 = true;
+
hvs->regs = vc4_ioremap_regs(pdev, 0);
if (IS_ERR(hvs->regs))
return PTR_ERR(hvs->regs);
@@ -529,7 +540,10 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
hvs->regset.regs = hvs_regs;
hvs->regset.nregs = ARRAY_SIZE(hvs_regs);
- hvs->dlist = hvs->regs + SCALER_DLIST_START;
+ if (!hvs->hvs5)
+ hvs->dlist = hvs->regs + SCALER_DLIST_START;
+ else
+ hvs->dlist = hvs->regs + SCALER5_DLIST_START;
spin_lock_init(&hvs->mm_lock);
@@ -547,7 +561,12 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
* between planes when they don't overlap on the screen, but
* for now we just allocate globally.
*/
- drm_mm_init(&hvs->lbm_mm, 0, 96 * 1024);
+ if (!hvs->hvs5)
+ /* 96kB */
+ drm_mm_init(&hvs->lbm_mm, 0, 96 * 1024);
+ else
+ /* 70k words */
+ drm_mm_init(&hvs->lbm_mm, 0, 70 * 2 * 1024);
/* Upload filter kernels. We only have the one for now, so we
* keep it around for the lifetime of the driver.
@@ -632,6 +651,7 @@ static int vc4_hvs_dev_remove(struct platform_device *pdev)
}
static const struct of_device_id vc4_hvs_dt_match[] = {
+ { .compatible = "brcm,bcm2711-hvs" },
{ .compatible = "brcm,bcm2835-hvs" },
{}
};
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index d040d9f12c6d..20c949b57827 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -32,45 +32,60 @@ static const struct hvs_format {
u32 drm; /* DRM_FORMAT_* */
u32 hvs; /* HVS_FORMAT_* */
u32 pixel_order;
+ u32 pixel_order_hvs5;
} hvs_formats[] = {
{
- .drm = DRM_FORMAT_XRGB8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_XRGB8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ARGB,
},
{
- .drm = DRM_FORMAT_ARGB8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_ARGB8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ARGB,
},
{
- .drm = DRM_FORMAT_ABGR8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_ABGR8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ARGB,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_XBGR8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_XBGR8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ARGB,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_RGB565, .hvs = HVS_PIXEL_FORMAT_RGB565,
+ .drm = DRM_FORMAT_RGB565,
+ .hvs = HVS_PIXEL_FORMAT_RGB565,
.pixel_order = HVS_PIXEL_ORDER_XRGB,
},
{
- .drm = DRM_FORMAT_BGR565, .hvs = HVS_PIXEL_FORMAT_RGB565,
+ .drm = DRM_FORMAT_BGR565,
+ .hvs = HVS_PIXEL_FORMAT_RGB565,
.pixel_order = HVS_PIXEL_ORDER_XBGR,
},
{
- .drm = DRM_FORMAT_ARGB1555, .hvs = HVS_PIXEL_FORMAT_RGBA5551,
+ .drm = DRM_FORMAT_ARGB1555,
+ .hvs = HVS_PIXEL_FORMAT_RGBA5551,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_XRGB1555, .hvs = HVS_PIXEL_FORMAT_RGBA5551,
+ .drm = DRM_FORMAT_XRGB1555,
+ .hvs = HVS_PIXEL_FORMAT_RGBA5551,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_RGB888, .hvs = HVS_PIXEL_FORMAT_RGB888,
+ .drm = DRM_FORMAT_RGB888,
+ .hvs = HVS_PIXEL_FORMAT_RGB888,
.pixel_order = HVS_PIXEL_ORDER_XRGB,
},
{
- .drm = DRM_FORMAT_BGR888, .hvs = HVS_PIXEL_FORMAT_RGB888,
+ .drm = DRM_FORMAT_BGR888,
+ .hvs = HVS_PIXEL_FORMAT_RGB888,
.pixel_order = HVS_PIXEL_ORDER_XBGR,
},
{
@@ -776,35 +791,6 @@ static int vc4_plane_mode_set(struct drm_plane *plane,
return -EINVAL;
}
- /* Control word */
- vc4_dlist_write(vc4_state,
- SCALER_CTL0_VALID |
- (rotation & DRM_MODE_REFLECT_X ? SCALER_CTL0_HFLIP : 0) |
- (rotation & DRM_MODE_REFLECT_Y ? SCALER_CTL0_VFLIP : 0) |
- VC4_SET_FIELD(SCALER_CTL0_RGBA_EXPAND_ROUND, SCALER_CTL0_RGBA_EXPAND) |
- (format->pixel_order << SCALER_CTL0_ORDER_SHIFT) |
- (hvs_format << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
- VC4_SET_FIELD(tiling, SCALER_CTL0_TILING) |
- (vc4_state->is_unity ? SCALER_CTL0_UNITY : 0) |
- VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
- VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1));
-
- /* Position Word 0: Image Positions and Alpha Value */
- vc4_state->pos0_offset = vc4_state->dlist_count;
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(state->alpha >> 8, SCALER_POS0_FIXED_ALPHA) |
- VC4_SET_FIELD(vc4_state->crtc_x, SCALER_POS0_START_X) |
- VC4_SET_FIELD(vc4_state->crtc_y, SCALER_POS0_START_Y));
-
- /* Position Word 1: Scaled Image Dimensions. */
- if (!vc4_state->is_unity) {
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(vc4_state->crtc_w,
- SCALER_POS1_SCL_WIDTH) |
- VC4_SET_FIELD(vc4_state->crtc_h,
- SCALER_POS1_SCL_HEIGHT));
- }
-
/* Don't waste cycles mixing with plane alpha if the set alpha
* is opaque or there is no per-pixel alpha information.
* In any case we use the alpha property value as the fixed alpha.
@@ -812,20 +798,120 @@ static int vc4_plane_mode_set(struct drm_plane *plane,
mix_plane_alpha = state->alpha != DRM_BLEND_ALPHA_OPAQUE &&
fb->format->has_alpha;
- /* Position Word 2: Source Image Size, Alpha */
- vc4_state->pos2_offset = vc4_state->dlist_count;
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(fb->format->has_alpha ?
- SCALER_POS2_ALPHA_MODE_PIPELINE :
- SCALER_POS2_ALPHA_MODE_FIXED,
- SCALER_POS2_ALPHA_MODE) |
- (mix_plane_alpha ? SCALER_POS2_ALPHA_MIX : 0) |
- (fb->format->has_alpha ? SCALER_POS2_ALPHA_PREMULT : 0) |
- VC4_SET_FIELD(vc4_state->src_w[0], SCALER_POS2_WIDTH) |
- VC4_SET_FIELD(vc4_state->src_h[0], SCALER_POS2_HEIGHT));
+ if (!vc4->hvs->hvs5) {
+ /* Control word */
+ vc4_dlist_write(vc4_state,
+ SCALER_CTL0_VALID |
+ (rotation & DRM_MODE_REFLECT_X ? SCALER_CTL0_HFLIP : 0) |
+ (rotation & DRM_MODE_REFLECT_Y ? SCALER_CTL0_VFLIP : 0) |
+ VC4_SET_FIELD(SCALER_CTL0_RGBA_EXPAND_ROUND, SCALER_CTL0_RGBA_EXPAND) |
+ (format->pixel_order << SCALER_CTL0_ORDER_SHIFT) |
+ (hvs_format << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
+ VC4_SET_FIELD(tiling, SCALER_CTL0_TILING) |
+ (vc4_state->is_unity ? SCALER_CTL0_UNITY : 0) |
+ VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
+ VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1));
+
+ /* Position Word 0: Image Positions and Alpha Value */
+ vc4_state->pos0_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(state->alpha >> 8, SCALER_POS0_FIXED_ALPHA) |
+ VC4_SET_FIELD(vc4_state->crtc_x, SCALER_POS0_START_X) |
+ VC4_SET_FIELD(vc4_state->crtc_y, SCALER_POS0_START_Y));
+
+ /* Position Word 1: Scaled Image Dimensions. */
+ if (!vc4_state->is_unity) {
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(vc4_state->crtc_w,
+ SCALER_POS1_SCL_WIDTH) |
+ VC4_SET_FIELD(vc4_state->crtc_h,
+ SCALER_POS1_SCL_HEIGHT));
+ }
+
+ /* Position Word 2: Source Image Size, Alpha */
+ vc4_state->pos2_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(fb->format->has_alpha ?
+ SCALER_POS2_ALPHA_MODE_PIPELINE :
+ SCALER_POS2_ALPHA_MODE_FIXED,
+ SCALER_POS2_ALPHA_MODE) |
+ (mix_plane_alpha ? SCALER_POS2_ALPHA_MIX : 0) |
+ (fb->format->has_alpha ?
+ SCALER_POS2_ALPHA_PREMULT : 0) |
+ VC4_SET_FIELD(vc4_state->src_w[0],
+ SCALER_POS2_WIDTH) |
+ VC4_SET_FIELD(vc4_state->src_h[0],
+ SCALER_POS2_HEIGHT));
+
+ /* Position Word 3: Context. Written by the HVS. */
+ vc4_dlist_write(vc4_state, 0xc0c0c0c0);
+
+ } else {
+ u32 hvs_pixel_order = format->pixel_order;
- /* Position Word 3: Context. Written by the HVS. */
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
+ if (format->pixel_order_hvs5)
+ hvs_pixel_order = format->pixel_order_hvs5;
+
+ /* Control word */
+ vc4_dlist_write(vc4_state,
+ SCALER_CTL0_VALID |
+ (hvs_pixel_order << SCALER_CTL0_ORDER_SHIFT) |
+ (hvs_format << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
+ VC4_SET_FIELD(tiling, SCALER_CTL0_TILING) |
+ (vc4_state->is_unity ?
+ SCALER5_CTL0_UNITY : 0) |
+ VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
+ VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1) |
+ SCALER5_CTL0_ALPHA_EXPAND |
+ SCALER5_CTL0_RGB_EXPAND);
+
+ /* Position Word 0: Image Positions and Alpha Value */
+ vc4_state->pos0_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ (rotation & DRM_MODE_REFLECT_Y ?
+ SCALER5_POS0_VFLIP : 0) |
+ VC4_SET_FIELD(vc4_state->crtc_x,
+ SCALER_POS0_START_X) |
+ (rotation & DRM_MODE_REFLECT_X ?
+ SCALER5_POS0_HFLIP : 0) |
+ VC4_SET_FIELD(vc4_state->crtc_y,
+ SCALER5_POS0_START_Y)
+ );
+
+ /* Control Word 2 */
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(state->alpha >> 4,
+ SCALER5_CTL2_ALPHA) |
+ fb->format->has_alpha ?
+ SCALER5_CTL2_ALPHA_PREMULT : 0 |
+ (mix_plane_alpha ?
+ SCALER5_CTL2_ALPHA_MIX : 0) |
+ VC4_SET_FIELD(fb->format->has_alpha ?
+ SCALER5_CTL2_ALPHA_MODE_PIPELINE :
+ SCALER5_CTL2_ALPHA_MODE_FIXED,
+ SCALER5_CTL2_ALPHA_MODE)
+ );
+
+ /* Position Word 1: Scaled Image Dimensions. */
+ if (!vc4_state->is_unity) {
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(vc4_state->crtc_w,
+ SCALER_POS1_SCL_WIDTH) |
+ VC4_SET_FIELD(vc4_state->crtc_h,
+ SCALER_POS1_SCL_HEIGHT));
+ }
+
+ /* Position Word 2: Source Image Size */
+ vc4_state->pos2_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(vc4_state->src_w[0],
+ SCALER5_POS2_WIDTH) |
+ VC4_SET_FIELD(vc4_state->src_h[0],
+ SCALER5_POS2_HEIGHT));
+
+ /* Position Word 3: Context. Written by the HVS. */
+ vc4_dlist_write(vc4_state, 0xc0c0c0c0);
+ }
/* Pointer Word 0/1/2: RGB / Y / Cb / Cr Pointers
@@ -1203,6 +1289,10 @@ static bool vc4_format_mod_supported(struct drm_plane *plane,
default:
return false;
}
+ case DRM_FORMAT_RGBX1010102:
+ case DRM_FORMAT_BGRX1010102:
+ case DRM_FORMAT_RGBA1010102:
+ case DRM_FORMAT_BGRA1010102:
case DRM_FORMAT_YUV422:
case DRM_FORMAT_YVU422:
case DRM_FORMAT_YUV420:
diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h
index 324462cc9cd4..91b785725555 100644
--- a/drivers/gpu/drm/vc4/vc4_regs.h
+++ b/drivers/gpu/drm/vc4/vc4_regs.h
@@ -327,6 +327,20 @@
# define SCALER_DISPCTRLX_HEIGHT_MASK VC4_MASK(11, 0)
# define SCALER_DISPCTRLX_HEIGHT_SHIFT 0
+# define SCALER5_DISPCTRLX_WIDTH_MASK VC4_MASK(28, 16)
+# define SCALER5_DISPCTRLX_WIDTH_SHIFT 16
+/* Generates a single frame when VSTART is seen and stops at the last
+ * pixel read from the FIFO.
+ */
+# define SCALER5_DISPCTRLX_ONESHOT BIT(15)
+/* Processes a single context in the dlist and then task switch,
+ * instead of an entire line.
+ */
+# define SCALER5_DISPCTRLX_ONECTX_MASK VC4_MASK(14, 13)
+# define SCALER5_DISPCTRLX_ONECTX_SHIFT 13
+# define SCALER5_DISPCTRLX_HEIGHT_MASK VC4_MASK(12, 0)
+# define SCALER5_DISPCTRLX_HEIGHT_SHIFT 0
+
#define SCALER_DISPBKGND0 0x00000044
# define SCALER_DISPBKGND_AUTOHS BIT(31)
# define SCALER_DISPBKGND_INTERLACE BIT(30)
@@ -460,6 +474,8 @@
#define SCALER_DLIST_START 0x00002000
#define SCALER_DLIST_SIZE 0x00004000
+#define SCALER5_DLIST_START 0x00004000
+
#define VC4_HDMI_CORE_REV 0x000
#define VC4_HDMI_SW_RESET_CONTROL 0x004
@@ -825,6 +841,8 @@ enum hvs_pixel_format {
HVS_PIXEL_FORMAT_PALETTE = 13,
HVS_PIXEL_FORMAT_YUV444_RGB = 14,
HVS_PIXEL_FORMAT_AYUV444_RGB = 15,
+ HVS_PIXEL_FORMAT_RGBA1010102 = 16,
+ HVS_PIXEL_FORMAT_YCBCR_10BIT = 17,
};
/* Note: the LSB is the rightmost character shown. Only valid for
@@ -879,6 +897,10 @@ enum hvs_pixel_format {
#define SCALER_CTL0_RGBA_EXPAND_MSB 2
#define SCALER_CTL0_RGBA_EXPAND_ROUND 3
+#define SCALER5_CTL0_ALPHA_EXPAND BIT(12)
+
+#define SCALER5_CTL0_RGB_EXPAND BIT(11)
+
#define SCALER_CTL0_SCL1_MASK VC4_MASK(10, 8)
#define SCALER_CTL0_SCL1_SHIFT 8
@@ -896,10 +918,13 @@ enum hvs_pixel_format {
/* Set to indicate no scaling. */
#define SCALER_CTL0_UNITY BIT(4)
+#define SCALER5_CTL0_UNITY BIT(15)
#define SCALER_CTL0_PIXEL_FORMAT_MASK VC4_MASK(3, 0)
#define SCALER_CTL0_PIXEL_FORMAT_SHIFT 0
+#define SCALER5_CTL0_PIXEL_FORMAT_MASK VC4_MASK(4, 0)
+
#define SCALER_POS0_FIXED_ALPHA_MASK VC4_MASK(31, 24)
#define SCALER_POS0_FIXED_ALPHA_SHIFT 24
@@ -909,12 +934,48 @@ enum hvs_pixel_format {
#define SCALER_POS0_START_X_MASK VC4_MASK(11, 0)
#define SCALER_POS0_START_X_SHIFT 0
+#define SCALER5_POS0_START_Y_MASK VC4_MASK(27, 16)
+#define SCALER5_POS0_START_Y_SHIFT 16
+
+#define SCALER5_POS0_START_X_MASK VC4_MASK(13, 0)
+#define SCALER5_POS0_START_X_SHIFT 0
+
+#define SCALER5_POS0_VFLIP BIT(31)
+#define SCALER5_POS0_HFLIP BIT(15)
+
+#define SCALER5_CTL2_ALPHA_MODE_MASK VC4_MASK(31, 30)
+#define SCALER5_CTL2_ALPHA_MODE_SHIFT 30
+#define SCALER5_CTL2_ALPHA_MODE_PIPELINE 0
+#define SCALER5_CTL2_ALPHA_MODE_FIXED 1
+#define SCALER5_CTL2_ALPHA_MODE_FIXED_NONZERO 2
+#define SCALER5_CTL2_ALPHA_MODE_FIXED_OVER_0x07 3
+
+#define SCALER5_CTL2_ALPHA_PREMULT BIT(29)
+
+#define SCALER5_CTL2_ALPHA_MIX BIT(28)
+
+#define SCALER5_CTL2_ALPHA_LOC BIT(25)
+
+#define SCALER5_CTL2_MAP_SEL_MASK VC4_MASK(18, 17)
+#define SCALER5_CTL2_MAP_SEL_SHIFT 17
+
+#define SCALER5_CTL2_GAMMA BIT(16)
+
+#define SCALER5_CTL2_ALPHA_MASK VC4_MASK(15, 4)
+#define SCALER5_CTL2_ALPHA_SHIFT 4
+
#define SCALER_POS1_SCL_HEIGHT_MASK VC4_MASK(27, 16)
#define SCALER_POS1_SCL_HEIGHT_SHIFT 16
#define SCALER_POS1_SCL_WIDTH_MASK VC4_MASK(11, 0)
#define SCALER_POS1_SCL_WIDTH_SHIFT 0
+#define SCALER5_POS1_SCL_HEIGHT_MASK VC4_MASK(28, 16)
+#define SCALER5_POS1_SCL_HEIGHT_SHIFT 16
+
+#define SCALER5_POS1_SCL_WIDTH_MASK VC4_MASK(12, 0)
+#define SCALER5_POS1_SCL_WIDTH_SHIFT 0
+
#define SCALER_POS2_ALPHA_MODE_MASK VC4_MASK(31, 30)
#define SCALER_POS2_ALPHA_MODE_SHIFT 30
#define SCALER_POS2_ALPHA_MODE_PIPELINE 0
@@ -930,6 +991,12 @@ enum hvs_pixel_format {
#define SCALER_POS2_WIDTH_MASK VC4_MASK(11, 0)
#define SCALER_POS2_WIDTH_SHIFT 0
+#define SCALER5_POS2_HEIGHT_MASK VC4_MASK(28, 16)
+#define SCALER5_POS2_HEIGHT_SHIFT 16
+
+#define SCALER5_POS2_WIDTH_MASK VC4_MASK(12, 0)
+#define SCALER5_POS2_WIDTH_SHIFT 0
+
/* Color Space Conversion words. Some values are S2.8 signed
* integers, except that the 2 integer bits map as {0x0: 0, 0x1: 1,
* 0x2: 2, 0x3: -1}
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 02/80] drm/vc4: Add support for the BCM2711 HVS5
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HVS found in the BCM2711 is slightly different from the previous
generations.
Most notably, the display list layout changes a bit, the LBM doesn't have
the same size and the formats ordering for some formats is swapped.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 4 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 34 ++++--
drivers/gpu/drm/vc4/vc4_plane.c | 194 ++++++++++++++++++++++++---------
drivers/gpu/drm/vc4/vc4_regs.h | 67 +++++++++++-
4 files changed, 240 insertions(+), 59 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index fa19160c801f..e4cde1f9224b 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -329,7 +329,11 @@ struct vc4_hvs {
spinlock_t mm_lock;
struct drm_mm_node mitchell_netravali_filter;
+
struct debugfs_regset32 regset;
+
+ /* HVS version 5 flag, therefore requires updated dlist structures */
+ bool hvs5;
};
struct vc4_plane {
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 2d2bf59c0503..836d8799d79e 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -277,11 +277,19 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
* mode.
*/
dispctrl = SCALER_DISPCTRLX_ENABLE;
- dispctrl |= VC4_SET_FIELD(mode->hdisplay,
- SCALER_DISPCTRLX_WIDTH) |
- VC4_SET_FIELD(mode->vdisplay,
- SCALER_DISPCTRLX_HEIGHT) |
- (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
+
+ if (!vc4->hvs->hvs5)
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
+ else
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER5_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER5_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
HVS_WRITE(SCALER_DISPCTRLX(vc4_crtc->channel), dispctrl);
}
@@ -521,6 +529,9 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
hvs->pdev = pdev;
+ if (of_device_is_compatible(pdev->dev.of_node, "brcm,bcm2711-hvs"))
+ hvs->hvs5 = true;
+
hvs->regs = vc4_ioremap_regs(pdev, 0);
if (IS_ERR(hvs->regs))
return PTR_ERR(hvs->regs);
@@ -529,7 +540,10 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
hvs->regset.regs = hvs_regs;
hvs->regset.nregs = ARRAY_SIZE(hvs_regs);
- hvs->dlist = hvs->regs + SCALER_DLIST_START;
+ if (!hvs->hvs5)
+ hvs->dlist = hvs->regs + SCALER_DLIST_START;
+ else
+ hvs->dlist = hvs->regs + SCALER5_DLIST_START;
spin_lock_init(&hvs->mm_lock);
@@ -547,7 +561,12 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
* between planes when they don't overlap on the screen, but
* for now we just allocate globally.
*/
- drm_mm_init(&hvs->lbm_mm, 0, 96 * 1024);
+ if (!hvs->hvs5)
+ /* 96kB */
+ drm_mm_init(&hvs->lbm_mm, 0, 96 * 1024);
+ else
+ /* 70k words */
+ drm_mm_init(&hvs->lbm_mm, 0, 70 * 2 * 1024);
/* Upload filter kernels. We only have the one for now, so we
* keep it around for the lifetime of the driver.
@@ -632,6 +651,7 @@ static int vc4_hvs_dev_remove(struct platform_device *pdev)
}
static const struct of_device_id vc4_hvs_dt_match[] = {
+ { .compatible = "brcm,bcm2711-hvs" },
{ .compatible = "brcm,bcm2835-hvs" },
{}
};
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index d040d9f12c6d..20c949b57827 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -32,45 +32,60 @@ static const struct hvs_format {
u32 drm; /* DRM_FORMAT_* */
u32 hvs; /* HVS_FORMAT_* */
u32 pixel_order;
+ u32 pixel_order_hvs5;
} hvs_formats[] = {
{
- .drm = DRM_FORMAT_XRGB8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_XRGB8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ARGB,
},
{
- .drm = DRM_FORMAT_ARGB8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_ARGB8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ARGB,
},
{
- .drm = DRM_FORMAT_ABGR8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_ABGR8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ARGB,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_XBGR8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_XBGR8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ARGB,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_RGB565, .hvs = HVS_PIXEL_FORMAT_RGB565,
+ .drm = DRM_FORMAT_RGB565,
+ .hvs = HVS_PIXEL_FORMAT_RGB565,
.pixel_order = HVS_PIXEL_ORDER_XRGB,
},
{
- .drm = DRM_FORMAT_BGR565, .hvs = HVS_PIXEL_FORMAT_RGB565,
+ .drm = DRM_FORMAT_BGR565,
+ .hvs = HVS_PIXEL_FORMAT_RGB565,
.pixel_order = HVS_PIXEL_ORDER_XBGR,
},
{
- .drm = DRM_FORMAT_ARGB1555, .hvs = HVS_PIXEL_FORMAT_RGBA5551,
+ .drm = DRM_FORMAT_ARGB1555,
+ .hvs = HVS_PIXEL_FORMAT_RGBA5551,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_XRGB1555, .hvs = HVS_PIXEL_FORMAT_RGBA5551,
+ .drm = DRM_FORMAT_XRGB1555,
+ .hvs = HVS_PIXEL_FORMAT_RGBA5551,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_RGB888, .hvs = HVS_PIXEL_FORMAT_RGB888,
+ .drm = DRM_FORMAT_RGB888,
+ .hvs = HVS_PIXEL_FORMAT_RGB888,
.pixel_order = HVS_PIXEL_ORDER_XRGB,
},
{
- .drm = DRM_FORMAT_BGR888, .hvs = HVS_PIXEL_FORMAT_RGB888,
+ .drm = DRM_FORMAT_BGR888,
+ .hvs = HVS_PIXEL_FORMAT_RGB888,
.pixel_order = HVS_PIXEL_ORDER_XBGR,
},
{
@@ -776,35 +791,6 @@ static int vc4_plane_mode_set(struct drm_plane *plane,
return -EINVAL;
}
- /* Control word */
- vc4_dlist_write(vc4_state,
- SCALER_CTL0_VALID |
- (rotation & DRM_MODE_REFLECT_X ? SCALER_CTL0_HFLIP : 0) |
- (rotation & DRM_MODE_REFLECT_Y ? SCALER_CTL0_VFLIP : 0) |
- VC4_SET_FIELD(SCALER_CTL0_RGBA_EXPAND_ROUND, SCALER_CTL0_RGBA_EXPAND) |
- (format->pixel_order << SCALER_CTL0_ORDER_SHIFT) |
- (hvs_format << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
- VC4_SET_FIELD(tiling, SCALER_CTL0_TILING) |
- (vc4_state->is_unity ? SCALER_CTL0_UNITY : 0) |
- VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
- VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1));
-
- /* Position Word 0: Image Positions and Alpha Value */
- vc4_state->pos0_offset = vc4_state->dlist_count;
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(state->alpha >> 8, SCALER_POS0_FIXED_ALPHA) |
- VC4_SET_FIELD(vc4_state->crtc_x, SCALER_POS0_START_X) |
- VC4_SET_FIELD(vc4_state->crtc_y, SCALER_POS0_START_Y));
-
- /* Position Word 1: Scaled Image Dimensions. */
- if (!vc4_state->is_unity) {
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(vc4_state->crtc_w,
- SCALER_POS1_SCL_WIDTH) |
- VC4_SET_FIELD(vc4_state->crtc_h,
- SCALER_POS1_SCL_HEIGHT));
- }
-
/* Don't waste cycles mixing with plane alpha if the set alpha
* is opaque or there is no per-pixel alpha information.
* In any case we use the alpha property value as the fixed alpha.
@@ -812,20 +798,120 @@ static int vc4_plane_mode_set(struct drm_plane *plane,
mix_plane_alpha = state->alpha != DRM_BLEND_ALPHA_OPAQUE &&
fb->format->has_alpha;
- /* Position Word 2: Source Image Size, Alpha */
- vc4_state->pos2_offset = vc4_state->dlist_count;
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(fb->format->has_alpha ?
- SCALER_POS2_ALPHA_MODE_PIPELINE :
- SCALER_POS2_ALPHA_MODE_FIXED,
- SCALER_POS2_ALPHA_MODE) |
- (mix_plane_alpha ? SCALER_POS2_ALPHA_MIX : 0) |
- (fb->format->has_alpha ? SCALER_POS2_ALPHA_PREMULT : 0) |
- VC4_SET_FIELD(vc4_state->src_w[0], SCALER_POS2_WIDTH) |
- VC4_SET_FIELD(vc4_state->src_h[0], SCALER_POS2_HEIGHT));
+ if (!vc4->hvs->hvs5) {
+ /* Control word */
+ vc4_dlist_write(vc4_state,
+ SCALER_CTL0_VALID |
+ (rotation & DRM_MODE_REFLECT_X ? SCALER_CTL0_HFLIP : 0) |
+ (rotation & DRM_MODE_REFLECT_Y ? SCALER_CTL0_VFLIP : 0) |
+ VC4_SET_FIELD(SCALER_CTL0_RGBA_EXPAND_ROUND, SCALER_CTL0_RGBA_EXPAND) |
+ (format->pixel_order << SCALER_CTL0_ORDER_SHIFT) |
+ (hvs_format << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
+ VC4_SET_FIELD(tiling, SCALER_CTL0_TILING) |
+ (vc4_state->is_unity ? SCALER_CTL0_UNITY : 0) |
+ VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
+ VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1));
+
+ /* Position Word 0: Image Positions and Alpha Value */
+ vc4_state->pos0_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(state->alpha >> 8, SCALER_POS0_FIXED_ALPHA) |
+ VC4_SET_FIELD(vc4_state->crtc_x, SCALER_POS0_START_X) |
+ VC4_SET_FIELD(vc4_state->crtc_y, SCALER_POS0_START_Y));
+
+ /* Position Word 1: Scaled Image Dimensions. */
+ if (!vc4_state->is_unity) {
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(vc4_state->crtc_w,
+ SCALER_POS1_SCL_WIDTH) |
+ VC4_SET_FIELD(vc4_state->crtc_h,
+ SCALER_POS1_SCL_HEIGHT));
+ }
+
+ /* Position Word 2: Source Image Size, Alpha */
+ vc4_state->pos2_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(fb->format->has_alpha ?
+ SCALER_POS2_ALPHA_MODE_PIPELINE :
+ SCALER_POS2_ALPHA_MODE_FIXED,
+ SCALER_POS2_ALPHA_MODE) |
+ (mix_plane_alpha ? SCALER_POS2_ALPHA_MIX : 0) |
+ (fb->format->has_alpha ?
+ SCALER_POS2_ALPHA_PREMULT : 0) |
+ VC4_SET_FIELD(vc4_state->src_w[0],
+ SCALER_POS2_WIDTH) |
+ VC4_SET_FIELD(vc4_state->src_h[0],
+ SCALER_POS2_HEIGHT));
+
+ /* Position Word 3: Context. Written by the HVS. */
+ vc4_dlist_write(vc4_state, 0xc0c0c0c0);
+
+ } else {
+ u32 hvs_pixel_order = format->pixel_order;
- /* Position Word 3: Context. Written by the HVS. */
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
+ if (format->pixel_order_hvs5)
+ hvs_pixel_order = format->pixel_order_hvs5;
+
+ /* Control word */
+ vc4_dlist_write(vc4_state,
+ SCALER_CTL0_VALID |
+ (hvs_pixel_order << SCALER_CTL0_ORDER_SHIFT) |
+ (hvs_format << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
+ VC4_SET_FIELD(tiling, SCALER_CTL0_TILING) |
+ (vc4_state->is_unity ?
+ SCALER5_CTL0_UNITY : 0) |
+ VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
+ VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1) |
+ SCALER5_CTL0_ALPHA_EXPAND |
+ SCALER5_CTL0_RGB_EXPAND);
+
+ /* Position Word 0: Image Positions and Alpha Value */
+ vc4_state->pos0_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ (rotation & DRM_MODE_REFLECT_Y ?
+ SCALER5_POS0_VFLIP : 0) |
+ VC4_SET_FIELD(vc4_state->crtc_x,
+ SCALER_POS0_START_X) |
+ (rotation & DRM_MODE_REFLECT_X ?
+ SCALER5_POS0_HFLIP : 0) |
+ VC4_SET_FIELD(vc4_state->crtc_y,
+ SCALER5_POS0_START_Y)
+ );
+
+ /* Control Word 2 */
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(state->alpha >> 4,
+ SCALER5_CTL2_ALPHA) |
+ fb->format->has_alpha ?
+ SCALER5_CTL2_ALPHA_PREMULT : 0 |
+ (mix_plane_alpha ?
+ SCALER5_CTL2_ALPHA_MIX : 0) |
+ VC4_SET_FIELD(fb->format->has_alpha ?
+ SCALER5_CTL2_ALPHA_MODE_PIPELINE :
+ SCALER5_CTL2_ALPHA_MODE_FIXED,
+ SCALER5_CTL2_ALPHA_MODE)
+ );
+
+ /* Position Word 1: Scaled Image Dimensions. */
+ if (!vc4_state->is_unity) {
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(vc4_state->crtc_w,
+ SCALER_POS1_SCL_WIDTH) |
+ VC4_SET_FIELD(vc4_state->crtc_h,
+ SCALER_POS1_SCL_HEIGHT));
+ }
+
+ /* Position Word 2: Source Image Size */
+ vc4_state->pos2_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(vc4_state->src_w[0],
+ SCALER5_POS2_WIDTH) |
+ VC4_SET_FIELD(vc4_state->src_h[0],
+ SCALER5_POS2_HEIGHT));
+
+ /* Position Word 3: Context. Written by the HVS. */
+ vc4_dlist_write(vc4_state, 0xc0c0c0c0);
+ }
/* Pointer Word 0/1/2: RGB / Y / Cb / Cr Pointers
@@ -1203,6 +1289,10 @@ static bool vc4_format_mod_supported(struct drm_plane *plane,
default:
return false;
}
+ case DRM_FORMAT_RGBX1010102:
+ case DRM_FORMAT_BGRX1010102:
+ case DRM_FORMAT_RGBA1010102:
+ case DRM_FORMAT_BGRA1010102:
case DRM_FORMAT_YUV422:
case DRM_FORMAT_YVU422:
case DRM_FORMAT_YUV420:
diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h
index 324462cc9cd4..91b785725555 100644
--- a/drivers/gpu/drm/vc4/vc4_regs.h
+++ b/drivers/gpu/drm/vc4/vc4_regs.h
@@ -327,6 +327,20 @@
# define SCALER_DISPCTRLX_HEIGHT_MASK VC4_MASK(11, 0)
# define SCALER_DISPCTRLX_HEIGHT_SHIFT 0
+# define SCALER5_DISPCTRLX_WIDTH_MASK VC4_MASK(28, 16)
+# define SCALER5_DISPCTRLX_WIDTH_SHIFT 16
+/* Generates a single frame when VSTART is seen and stops at the last
+ * pixel read from the FIFO.
+ */
+# define SCALER5_DISPCTRLX_ONESHOT BIT(15)
+/* Processes a single context in the dlist and then task switch,
+ * instead of an entire line.
+ */
+# define SCALER5_DISPCTRLX_ONECTX_MASK VC4_MASK(14, 13)
+# define SCALER5_DISPCTRLX_ONECTX_SHIFT 13
+# define SCALER5_DISPCTRLX_HEIGHT_MASK VC4_MASK(12, 0)
+# define SCALER5_DISPCTRLX_HEIGHT_SHIFT 0
+
#define SCALER_DISPBKGND0 0x00000044
# define SCALER_DISPBKGND_AUTOHS BIT(31)
# define SCALER_DISPBKGND_INTERLACE BIT(30)
@@ -460,6 +474,8 @@
#define SCALER_DLIST_START 0x00002000
#define SCALER_DLIST_SIZE 0x00004000
+#define SCALER5_DLIST_START 0x00004000
+
#define VC4_HDMI_CORE_REV 0x000
#define VC4_HDMI_SW_RESET_CONTROL 0x004
@@ -825,6 +841,8 @@ enum hvs_pixel_format {
HVS_PIXEL_FORMAT_PALETTE = 13,
HVS_PIXEL_FORMAT_YUV444_RGB = 14,
HVS_PIXEL_FORMAT_AYUV444_RGB = 15,
+ HVS_PIXEL_FORMAT_RGBA1010102 = 16,
+ HVS_PIXEL_FORMAT_YCBCR_10BIT = 17,
};
/* Note: the LSB is the rightmost character shown. Only valid for
@@ -879,6 +897,10 @@ enum hvs_pixel_format {
#define SCALER_CTL0_RGBA_EXPAND_MSB 2
#define SCALER_CTL0_RGBA_EXPAND_ROUND 3
+#define SCALER5_CTL0_ALPHA_EXPAND BIT(12)
+
+#define SCALER5_CTL0_RGB_EXPAND BIT(11)
+
#define SCALER_CTL0_SCL1_MASK VC4_MASK(10, 8)
#define SCALER_CTL0_SCL1_SHIFT 8
@@ -896,10 +918,13 @@ enum hvs_pixel_format {
/* Set to indicate no scaling. */
#define SCALER_CTL0_UNITY BIT(4)
+#define SCALER5_CTL0_UNITY BIT(15)
#define SCALER_CTL0_PIXEL_FORMAT_MASK VC4_MASK(3, 0)
#define SCALER_CTL0_PIXEL_FORMAT_SHIFT 0
+#define SCALER5_CTL0_PIXEL_FORMAT_MASK VC4_MASK(4, 0)
+
#define SCALER_POS0_FIXED_ALPHA_MASK VC4_MASK(31, 24)
#define SCALER_POS0_FIXED_ALPHA_SHIFT 24
@@ -909,12 +934,48 @@ enum hvs_pixel_format {
#define SCALER_POS0_START_X_MASK VC4_MASK(11, 0)
#define SCALER_POS0_START_X_SHIFT 0
+#define SCALER5_POS0_START_Y_MASK VC4_MASK(27, 16)
+#define SCALER5_POS0_START_Y_SHIFT 16
+
+#define SCALER5_POS0_START_X_MASK VC4_MASK(13, 0)
+#define SCALER5_POS0_START_X_SHIFT 0
+
+#define SCALER5_POS0_VFLIP BIT(31)
+#define SCALER5_POS0_HFLIP BIT(15)
+
+#define SCALER5_CTL2_ALPHA_MODE_MASK VC4_MASK(31, 30)
+#define SCALER5_CTL2_ALPHA_MODE_SHIFT 30
+#define SCALER5_CTL2_ALPHA_MODE_PIPELINE 0
+#define SCALER5_CTL2_ALPHA_MODE_FIXED 1
+#define SCALER5_CTL2_ALPHA_MODE_FIXED_NONZERO 2
+#define SCALER5_CTL2_ALPHA_MODE_FIXED_OVER_0x07 3
+
+#define SCALER5_CTL2_ALPHA_PREMULT BIT(29)
+
+#define SCALER5_CTL2_ALPHA_MIX BIT(28)
+
+#define SCALER5_CTL2_ALPHA_LOC BIT(25)
+
+#define SCALER5_CTL2_MAP_SEL_MASK VC4_MASK(18, 17)
+#define SCALER5_CTL2_MAP_SEL_SHIFT 17
+
+#define SCALER5_CTL2_GAMMA BIT(16)
+
+#define SCALER5_CTL2_ALPHA_MASK VC4_MASK(15, 4)
+#define SCALER5_CTL2_ALPHA_SHIFT 4
+
#define SCALER_POS1_SCL_HEIGHT_MASK VC4_MASK(27, 16)
#define SCALER_POS1_SCL_HEIGHT_SHIFT 16
#define SCALER_POS1_SCL_WIDTH_MASK VC4_MASK(11, 0)
#define SCALER_POS1_SCL_WIDTH_SHIFT 0
+#define SCALER5_POS1_SCL_HEIGHT_MASK VC4_MASK(28, 16)
+#define SCALER5_POS1_SCL_HEIGHT_SHIFT 16
+
+#define SCALER5_POS1_SCL_WIDTH_MASK VC4_MASK(12, 0)
+#define SCALER5_POS1_SCL_WIDTH_SHIFT 0
+
#define SCALER_POS2_ALPHA_MODE_MASK VC4_MASK(31, 30)
#define SCALER_POS2_ALPHA_MODE_SHIFT 30
#define SCALER_POS2_ALPHA_MODE_PIPELINE 0
@@ -930,6 +991,12 @@ enum hvs_pixel_format {
#define SCALER_POS2_WIDTH_MASK VC4_MASK(11, 0)
#define SCALER_POS2_WIDTH_SHIFT 0
+#define SCALER5_POS2_HEIGHT_MASK VC4_MASK(28, 16)
+#define SCALER5_POS2_HEIGHT_SHIFT 16
+
+#define SCALER5_POS2_WIDTH_MASK VC4_MASK(12, 0)
+#define SCALER5_POS2_WIDTH_SHIFT 0
+
/* Color Space Conversion words. Some values are S2.8 signed
* integers, except that the 2 integer bits map as {0x0: 0, 0x1: 1,
* 0x2: 2, 0x3: -1}
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 02/80] drm/vc4: Add support for the BCM2711 HVS5
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HVS found in the BCM2711 is slightly different from the previous
generations.
Most notably, the display list layout changes a bit, the LBM doesn't have
the same size and the formats ordering for some formats is swapped.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 4 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 34 ++++--
drivers/gpu/drm/vc4/vc4_plane.c | 194 ++++++++++++++++++++++++---------
drivers/gpu/drm/vc4/vc4_regs.h | 67 +++++++++++-
4 files changed, 240 insertions(+), 59 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index fa19160c801f..e4cde1f9224b 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -329,7 +329,11 @@ struct vc4_hvs {
spinlock_t mm_lock;
struct drm_mm_node mitchell_netravali_filter;
+
struct debugfs_regset32 regset;
+
+ /* HVS version 5 flag, therefore requires updated dlist structures */
+ bool hvs5;
};
struct vc4_plane {
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 2d2bf59c0503..836d8799d79e 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -277,11 +277,19 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
* mode.
*/
dispctrl = SCALER_DISPCTRLX_ENABLE;
- dispctrl |= VC4_SET_FIELD(mode->hdisplay,
- SCALER_DISPCTRLX_WIDTH) |
- VC4_SET_FIELD(mode->vdisplay,
- SCALER_DISPCTRLX_HEIGHT) |
- (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
+
+ if (!vc4->hvs->hvs5)
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
+ else
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER5_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER5_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
HVS_WRITE(SCALER_DISPCTRLX(vc4_crtc->channel), dispctrl);
}
@@ -521,6 +529,9 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
hvs->pdev = pdev;
+ if (of_device_is_compatible(pdev->dev.of_node, "brcm,bcm2711-hvs"))
+ hvs->hvs5 = true;
+
hvs->regs = vc4_ioremap_regs(pdev, 0);
if (IS_ERR(hvs->regs))
return PTR_ERR(hvs->regs);
@@ -529,7 +540,10 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
hvs->regset.regs = hvs_regs;
hvs->regset.nregs = ARRAY_SIZE(hvs_regs);
- hvs->dlist = hvs->regs + SCALER_DLIST_START;
+ if (!hvs->hvs5)
+ hvs->dlist = hvs->regs + SCALER_DLIST_START;
+ else
+ hvs->dlist = hvs->regs + SCALER5_DLIST_START;
spin_lock_init(&hvs->mm_lock);
@@ -547,7 +561,12 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
* between planes when they don't overlap on the screen, but
* for now we just allocate globally.
*/
- drm_mm_init(&hvs->lbm_mm, 0, 96 * 1024);
+ if (!hvs->hvs5)
+ /* 96kB */
+ drm_mm_init(&hvs->lbm_mm, 0, 96 * 1024);
+ else
+ /* 70k words */
+ drm_mm_init(&hvs->lbm_mm, 0, 70 * 2 * 1024);
/* Upload filter kernels. We only have the one for now, so we
* keep it around for the lifetime of the driver.
@@ -632,6 +651,7 @@ static int vc4_hvs_dev_remove(struct platform_device *pdev)
}
static const struct of_device_id vc4_hvs_dt_match[] = {
+ { .compatible = "brcm,bcm2711-hvs" },
{ .compatible = "brcm,bcm2835-hvs" },
{}
};
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index d040d9f12c6d..20c949b57827 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -32,45 +32,60 @@ static const struct hvs_format {
u32 drm; /* DRM_FORMAT_* */
u32 hvs; /* HVS_FORMAT_* */
u32 pixel_order;
+ u32 pixel_order_hvs5;
} hvs_formats[] = {
{
- .drm = DRM_FORMAT_XRGB8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_XRGB8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ARGB,
},
{
- .drm = DRM_FORMAT_ARGB8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_ARGB8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ARGB,
},
{
- .drm = DRM_FORMAT_ABGR8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_ABGR8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ARGB,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_XBGR8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
+ .drm = DRM_FORMAT_XBGR8888,
+ .hvs = HVS_PIXEL_FORMAT_RGBA8888,
.pixel_order = HVS_PIXEL_ORDER_ARGB,
+ .pixel_order_hvs5 = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_RGB565, .hvs = HVS_PIXEL_FORMAT_RGB565,
+ .drm = DRM_FORMAT_RGB565,
+ .hvs = HVS_PIXEL_FORMAT_RGB565,
.pixel_order = HVS_PIXEL_ORDER_XRGB,
},
{
- .drm = DRM_FORMAT_BGR565, .hvs = HVS_PIXEL_FORMAT_RGB565,
+ .drm = DRM_FORMAT_BGR565,
+ .hvs = HVS_PIXEL_FORMAT_RGB565,
.pixel_order = HVS_PIXEL_ORDER_XBGR,
},
{
- .drm = DRM_FORMAT_ARGB1555, .hvs = HVS_PIXEL_FORMAT_RGBA5551,
+ .drm = DRM_FORMAT_ARGB1555,
+ .hvs = HVS_PIXEL_FORMAT_RGBA5551,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_XRGB1555, .hvs = HVS_PIXEL_FORMAT_RGBA5551,
+ .drm = DRM_FORMAT_XRGB1555,
+ .hvs = HVS_PIXEL_FORMAT_RGBA5551,
.pixel_order = HVS_PIXEL_ORDER_ABGR,
},
{
- .drm = DRM_FORMAT_RGB888, .hvs = HVS_PIXEL_FORMAT_RGB888,
+ .drm = DRM_FORMAT_RGB888,
+ .hvs = HVS_PIXEL_FORMAT_RGB888,
.pixel_order = HVS_PIXEL_ORDER_XRGB,
},
{
- .drm = DRM_FORMAT_BGR888, .hvs = HVS_PIXEL_FORMAT_RGB888,
+ .drm = DRM_FORMAT_BGR888,
+ .hvs = HVS_PIXEL_FORMAT_RGB888,
.pixel_order = HVS_PIXEL_ORDER_XBGR,
},
{
@@ -776,35 +791,6 @@ static int vc4_plane_mode_set(struct drm_plane *plane,
return -EINVAL;
}
- /* Control word */
- vc4_dlist_write(vc4_state,
- SCALER_CTL0_VALID |
- (rotation & DRM_MODE_REFLECT_X ? SCALER_CTL0_HFLIP : 0) |
- (rotation & DRM_MODE_REFLECT_Y ? SCALER_CTL0_VFLIP : 0) |
- VC4_SET_FIELD(SCALER_CTL0_RGBA_EXPAND_ROUND, SCALER_CTL0_RGBA_EXPAND) |
- (format->pixel_order << SCALER_CTL0_ORDER_SHIFT) |
- (hvs_format << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
- VC4_SET_FIELD(tiling, SCALER_CTL0_TILING) |
- (vc4_state->is_unity ? SCALER_CTL0_UNITY : 0) |
- VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
- VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1));
-
- /* Position Word 0: Image Positions and Alpha Value */
- vc4_state->pos0_offset = vc4_state->dlist_count;
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(state->alpha >> 8, SCALER_POS0_FIXED_ALPHA) |
- VC4_SET_FIELD(vc4_state->crtc_x, SCALER_POS0_START_X) |
- VC4_SET_FIELD(vc4_state->crtc_y, SCALER_POS0_START_Y));
-
- /* Position Word 1: Scaled Image Dimensions. */
- if (!vc4_state->is_unity) {
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(vc4_state->crtc_w,
- SCALER_POS1_SCL_WIDTH) |
- VC4_SET_FIELD(vc4_state->crtc_h,
- SCALER_POS1_SCL_HEIGHT));
- }
-
/* Don't waste cycles mixing with plane alpha if the set alpha
* is opaque or there is no per-pixel alpha information.
* In any case we use the alpha property value as the fixed alpha.
@@ -812,20 +798,120 @@ static int vc4_plane_mode_set(struct drm_plane *plane,
mix_plane_alpha = state->alpha != DRM_BLEND_ALPHA_OPAQUE &&
fb->format->has_alpha;
- /* Position Word 2: Source Image Size, Alpha */
- vc4_state->pos2_offset = vc4_state->dlist_count;
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(fb->format->has_alpha ?
- SCALER_POS2_ALPHA_MODE_PIPELINE :
- SCALER_POS2_ALPHA_MODE_FIXED,
- SCALER_POS2_ALPHA_MODE) |
- (mix_plane_alpha ? SCALER_POS2_ALPHA_MIX : 0) |
- (fb->format->has_alpha ? SCALER_POS2_ALPHA_PREMULT : 0) |
- VC4_SET_FIELD(vc4_state->src_w[0], SCALER_POS2_WIDTH) |
- VC4_SET_FIELD(vc4_state->src_h[0], SCALER_POS2_HEIGHT));
+ if (!vc4->hvs->hvs5) {
+ /* Control word */
+ vc4_dlist_write(vc4_state,
+ SCALER_CTL0_VALID |
+ (rotation & DRM_MODE_REFLECT_X ? SCALER_CTL0_HFLIP : 0) |
+ (rotation & DRM_MODE_REFLECT_Y ? SCALER_CTL0_VFLIP : 0) |
+ VC4_SET_FIELD(SCALER_CTL0_RGBA_EXPAND_ROUND, SCALER_CTL0_RGBA_EXPAND) |
+ (format->pixel_order << SCALER_CTL0_ORDER_SHIFT) |
+ (hvs_format << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
+ VC4_SET_FIELD(tiling, SCALER_CTL0_TILING) |
+ (vc4_state->is_unity ? SCALER_CTL0_UNITY : 0) |
+ VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
+ VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1));
+
+ /* Position Word 0: Image Positions and Alpha Value */
+ vc4_state->pos0_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(state->alpha >> 8, SCALER_POS0_FIXED_ALPHA) |
+ VC4_SET_FIELD(vc4_state->crtc_x, SCALER_POS0_START_X) |
+ VC4_SET_FIELD(vc4_state->crtc_y, SCALER_POS0_START_Y));
+
+ /* Position Word 1: Scaled Image Dimensions. */
+ if (!vc4_state->is_unity) {
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(vc4_state->crtc_w,
+ SCALER_POS1_SCL_WIDTH) |
+ VC4_SET_FIELD(vc4_state->crtc_h,
+ SCALER_POS1_SCL_HEIGHT));
+ }
+
+ /* Position Word 2: Source Image Size, Alpha */
+ vc4_state->pos2_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(fb->format->has_alpha ?
+ SCALER_POS2_ALPHA_MODE_PIPELINE :
+ SCALER_POS2_ALPHA_MODE_FIXED,
+ SCALER_POS2_ALPHA_MODE) |
+ (mix_plane_alpha ? SCALER_POS2_ALPHA_MIX : 0) |
+ (fb->format->has_alpha ?
+ SCALER_POS2_ALPHA_PREMULT : 0) |
+ VC4_SET_FIELD(vc4_state->src_w[0],
+ SCALER_POS2_WIDTH) |
+ VC4_SET_FIELD(vc4_state->src_h[0],
+ SCALER_POS2_HEIGHT));
+
+ /* Position Word 3: Context. Written by the HVS. */
+ vc4_dlist_write(vc4_state, 0xc0c0c0c0);
+
+ } else {
+ u32 hvs_pixel_order = format->pixel_order;
- /* Position Word 3: Context. Written by the HVS. */
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
+ if (format->pixel_order_hvs5)
+ hvs_pixel_order = format->pixel_order_hvs5;
+
+ /* Control word */
+ vc4_dlist_write(vc4_state,
+ SCALER_CTL0_VALID |
+ (hvs_pixel_order << SCALER_CTL0_ORDER_SHIFT) |
+ (hvs_format << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
+ VC4_SET_FIELD(tiling, SCALER_CTL0_TILING) |
+ (vc4_state->is_unity ?
+ SCALER5_CTL0_UNITY : 0) |
+ VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
+ VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1) |
+ SCALER5_CTL0_ALPHA_EXPAND |
+ SCALER5_CTL0_RGB_EXPAND);
+
+ /* Position Word 0: Image Positions and Alpha Value */
+ vc4_state->pos0_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ (rotation & DRM_MODE_REFLECT_Y ?
+ SCALER5_POS0_VFLIP : 0) |
+ VC4_SET_FIELD(vc4_state->crtc_x,
+ SCALER_POS0_START_X) |
+ (rotation & DRM_MODE_REFLECT_X ?
+ SCALER5_POS0_HFLIP : 0) |
+ VC4_SET_FIELD(vc4_state->crtc_y,
+ SCALER5_POS0_START_Y)
+ );
+
+ /* Control Word 2 */
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(state->alpha >> 4,
+ SCALER5_CTL2_ALPHA) |
+ fb->format->has_alpha ?
+ SCALER5_CTL2_ALPHA_PREMULT : 0 |
+ (mix_plane_alpha ?
+ SCALER5_CTL2_ALPHA_MIX : 0) |
+ VC4_SET_FIELD(fb->format->has_alpha ?
+ SCALER5_CTL2_ALPHA_MODE_PIPELINE :
+ SCALER5_CTL2_ALPHA_MODE_FIXED,
+ SCALER5_CTL2_ALPHA_MODE)
+ );
+
+ /* Position Word 1: Scaled Image Dimensions. */
+ if (!vc4_state->is_unity) {
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(vc4_state->crtc_w,
+ SCALER_POS1_SCL_WIDTH) |
+ VC4_SET_FIELD(vc4_state->crtc_h,
+ SCALER_POS1_SCL_HEIGHT));
+ }
+
+ /* Position Word 2: Source Image Size */
+ vc4_state->pos2_offset = vc4_state->dlist_count;
+ vc4_dlist_write(vc4_state,
+ VC4_SET_FIELD(vc4_state->src_w[0],
+ SCALER5_POS2_WIDTH) |
+ VC4_SET_FIELD(vc4_state->src_h[0],
+ SCALER5_POS2_HEIGHT));
+
+ /* Position Word 3: Context. Written by the HVS. */
+ vc4_dlist_write(vc4_state, 0xc0c0c0c0);
+ }
/* Pointer Word 0/1/2: RGB / Y / Cb / Cr Pointers
@@ -1203,6 +1289,10 @@ static bool vc4_format_mod_supported(struct drm_plane *plane,
default:
return false;
}
+ case DRM_FORMAT_RGBX1010102:
+ case DRM_FORMAT_BGRX1010102:
+ case DRM_FORMAT_RGBA1010102:
+ case DRM_FORMAT_BGRA1010102:
case DRM_FORMAT_YUV422:
case DRM_FORMAT_YVU422:
case DRM_FORMAT_YUV420:
diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h
index 324462cc9cd4..91b785725555 100644
--- a/drivers/gpu/drm/vc4/vc4_regs.h
+++ b/drivers/gpu/drm/vc4/vc4_regs.h
@@ -327,6 +327,20 @@
# define SCALER_DISPCTRLX_HEIGHT_MASK VC4_MASK(11, 0)
# define SCALER_DISPCTRLX_HEIGHT_SHIFT 0
+# define SCALER5_DISPCTRLX_WIDTH_MASK VC4_MASK(28, 16)
+# define SCALER5_DISPCTRLX_WIDTH_SHIFT 16
+/* Generates a single frame when VSTART is seen and stops at the last
+ * pixel read from the FIFO.
+ */
+# define SCALER5_DISPCTRLX_ONESHOT BIT(15)
+/* Processes a single context in the dlist and then task switch,
+ * instead of an entire line.
+ */
+# define SCALER5_DISPCTRLX_ONECTX_MASK VC4_MASK(14, 13)
+# define SCALER5_DISPCTRLX_ONECTX_SHIFT 13
+# define SCALER5_DISPCTRLX_HEIGHT_MASK VC4_MASK(12, 0)
+# define SCALER5_DISPCTRLX_HEIGHT_SHIFT 0
+
#define SCALER_DISPBKGND0 0x00000044
# define SCALER_DISPBKGND_AUTOHS BIT(31)
# define SCALER_DISPBKGND_INTERLACE BIT(30)
@@ -460,6 +474,8 @@
#define SCALER_DLIST_START 0x00002000
#define SCALER_DLIST_SIZE 0x00004000
+#define SCALER5_DLIST_START 0x00004000
+
#define VC4_HDMI_CORE_REV 0x000
#define VC4_HDMI_SW_RESET_CONTROL 0x004
@@ -825,6 +841,8 @@ enum hvs_pixel_format {
HVS_PIXEL_FORMAT_PALETTE = 13,
HVS_PIXEL_FORMAT_YUV444_RGB = 14,
HVS_PIXEL_FORMAT_AYUV444_RGB = 15,
+ HVS_PIXEL_FORMAT_RGBA1010102 = 16,
+ HVS_PIXEL_FORMAT_YCBCR_10BIT = 17,
};
/* Note: the LSB is the rightmost character shown. Only valid for
@@ -879,6 +897,10 @@ enum hvs_pixel_format {
#define SCALER_CTL0_RGBA_EXPAND_MSB 2
#define SCALER_CTL0_RGBA_EXPAND_ROUND 3
+#define SCALER5_CTL0_ALPHA_EXPAND BIT(12)
+
+#define SCALER5_CTL0_RGB_EXPAND BIT(11)
+
#define SCALER_CTL0_SCL1_MASK VC4_MASK(10, 8)
#define SCALER_CTL0_SCL1_SHIFT 8
@@ -896,10 +918,13 @@ enum hvs_pixel_format {
/* Set to indicate no scaling. */
#define SCALER_CTL0_UNITY BIT(4)
+#define SCALER5_CTL0_UNITY BIT(15)
#define SCALER_CTL0_PIXEL_FORMAT_MASK VC4_MASK(3, 0)
#define SCALER_CTL0_PIXEL_FORMAT_SHIFT 0
+#define SCALER5_CTL0_PIXEL_FORMAT_MASK VC4_MASK(4, 0)
+
#define SCALER_POS0_FIXED_ALPHA_MASK VC4_MASK(31, 24)
#define SCALER_POS0_FIXED_ALPHA_SHIFT 24
@@ -909,12 +934,48 @@ enum hvs_pixel_format {
#define SCALER_POS0_START_X_MASK VC4_MASK(11, 0)
#define SCALER_POS0_START_X_SHIFT 0
+#define SCALER5_POS0_START_Y_MASK VC4_MASK(27, 16)
+#define SCALER5_POS0_START_Y_SHIFT 16
+
+#define SCALER5_POS0_START_X_MASK VC4_MASK(13, 0)
+#define SCALER5_POS0_START_X_SHIFT 0
+
+#define SCALER5_POS0_VFLIP BIT(31)
+#define SCALER5_POS0_HFLIP BIT(15)
+
+#define SCALER5_CTL2_ALPHA_MODE_MASK VC4_MASK(31, 30)
+#define SCALER5_CTL2_ALPHA_MODE_SHIFT 30
+#define SCALER5_CTL2_ALPHA_MODE_PIPELINE 0
+#define SCALER5_CTL2_ALPHA_MODE_FIXED 1
+#define SCALER5_CTL2_ALPHA_MODE_FIXED_NONZERO 2
+#define SCALER5_CTL2_ALPHA_MODE_FIXED_OVER_0x07 3
+
+#define SCALER5_CTL2_ALPHA_PREMULT BIT(29)
+
+#define SCALER5_CTL2_ALPHA_MIX BIT(28)
+
+#define SCALER5_CTL2_ALPHA_LOC BIT(25)
+
+#define SCALER5_CTL2_MAP_SEL_MASK VC4_MASK(18, 17)
+#define SCALER5_CTL2_MAP_SEL_SHIFT 17
+
+#define SCALER5_CTL2_GAMMA BIT(16)
+
+#define SCALER5_CTL2_ALPHA_MASK VC4_MASK(15, 4)
+#define SCALER5_CTL2_ALPHA_SHIFT 4
+
#define SCALER_POS1_SCL_HEIGHT_MASK VC4_MASK(27, 16)
#define SCALER_POS1_SCL_HEIGHT_SHIFT 16
#define SCALER_POS1_SCL_WIDTH_MASK VC4_MASK(11, 0)
#define SCALER_POS1_SCL_WIDTH_SHIFT 0
+#define SCALER5_POS1_SCL_HEIGHT_MASK VC4_MASK(28, 16)
+#define SCALER5_POS1_SCL_HEIGHT_SHIFT 16
+
+#define SCALER5_POS1_SCL_WIDTH_MASK VC4_MASK(12, 0)
+#define SCALER5_POS1_SCL_WIDTH_SHIFT 0
+
#define SCALER_POS2_ALPHA_MODE_MASK VC4_MASK(31, 30)
#define SCALER_POS2_ALPHA_MODE_SHIFT 30
#define SCALER_POS2_ALPHA_MODE_PIPELINE 0
@@ -930,6 +991,12 @@ enum hvs_pixel_format {
#define SCALER_POS2_WIDTH_MASK VC4_MASK(11, 0)
#define SCALER_POS2_WIDTH_SHIFT 0
+#define SCALER5_POS2_HEIGHT_MASK VC4_MASK(28, 16)
+#define SCALER5_POS2_HEIGHT_SHIFT 16
+
+#define SCALER5_POS2_WIDTH_MASK VC4_MASK(12, 0)
+#define SCALER5_POS2_WIDTH_SHIFT 0
+
/* Color Space Conversion words. Some values are S2.8 signed
* integers, except that the 2 integer bits map as {0x0: 0, 0x1: 1,
* 0x2: 2, 0x3: -1}
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 03/80] drm/vc4: hvs: Boost the core clock during modeset
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
In order to prevent timeouts and stalls in the pipeline, the core clock
needs to be maxed at 500MHz during a modeset on the BCM2711.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 2 ++
drivers/gpu/drm/vc4/vc4_hvs.c | 18 ++++++++++++++++++
drivers/gpu/drm/vc4/vc4_kms.c | 9 +++++++++
3 files changed, 29 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index e4cde1f9224b..6358f6ca8d56 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -320,6 +320,8 @@ struct vc4_hvs {
void __iomem *regs;
u32 __iomem *dlist;
+ struct clk *core_clk;
+
/* Memory manager for CRTCs to allocate space in the display
* list. Units are dwords.
*/
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 836d8799d79e..abdb43c4cc10 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -19,6 +19,7 @@
* each CRTC.
*/
+#include <linux/clk.h>
#include <linux/component.h>
#include <linux/platform_device.h>
@@ -540,6 +541,20 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
hvs->regset.regs = hvs_regs;
hvs->regset.nregs = ARRAY_SIZE(hvs_regs);
+ if (hvs->hvs5) {
+ hvs->core_clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(hvs->core_clk)) {
+ dev_err(&pdev->dev, "Couldn't get core clock\n");
+ return PTR_ERR(hvs->core_clk);
+ }
+
+ ret = clk_prepare_enable(hvs->core_clk);
+ if (ret) {
+ dev_err(&pdev->dev, "Couldn't enable the core clock\n");
+ return ret;
+ }
+ }
+
if (!hvs->hvs5)
hvs->dlist = hvs->regs + SCALER_DLIST_START;
else
@@ -624,6 +639,7 @@ static void vc4_hvs_unbind(struct device *dev, struct device *master,
{
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
+ struct vc4_hvs *hvs = vc4->hvs;
if (drm_mm_node_allocated(&vc4->hvs->mitchell_netravali_filter))
drm_mm_remove_node(&vc4->hvs->mitchell_netravali_filter);
@@ -631,6 +647,8 @@ static void vc4_hvs_unbind(struct device *dev, struct device *master,
drm_mm_takedown(&vc4->hvs->dlist_mm);
drm_mm_takedown(&vc4->hvs->lbm_mm);
+ clk_disable_unprepare(hvs->core_clk);
+
vc4->hvs = NULL;
}
diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index 08318e69061b..210cc2408087 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -11,6 +11,8 @@
* crtc, HDMI encoder).
*/
+#include <linux/clk.h>
+
#include <drm/drm_atomic.h>
#include <drm/drm_atomic_helper.h>
#include <drm/drm_crtc.h>
@@ -149,6 +151,7 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
{
struct drm_device *dev = state->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hvs *hvs = vc4->hvs;
struct vc4_crtc *vc4_crtc;
int i;
@@ -160,6 +163,9 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
vc4_hvs_mask_underrun(dev, vc4_crtc->channel);
}
+ if (vc4->hvs->hvs5)
+ clk_set_min_rate(hvs->core_clk, 500000000);
+
drm_atomic_helper_wait_for_fences(dev, state, false);
drm_atomic_helper_wait_for_dependencies(state);
@@ -182,6 +188,9 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
drm_atomic_helper_commit_cleanup_done(state);
+ if (vc4->hvs->hvs5)
+ clk_set_min_rate(hvs->core_clk, 0);
+
drm_atomic_state_put(state);
up(&vc4->async_modeset);
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 03/80] drm/vc4: hvs: Boost the core clock during modeset
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to prevent timeouts and stalls in the pipeline, the core clock
needs to be maxed at 500MHz during a modeset on the BCM2711.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 2 ++
drivers/gpu/drm/vc4/vc4_hvs.c | 18 ++++++++++++++++++
drivers/gpu/drm/vc4/vc4_kms.c | 9 +++++++++
3 files changed, 29 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index e4cde1f9224b..6358f6ca8d56 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -320,6 +320,8 @@ struct vc4_hvs {
void __iomem *regs;
u32 __iomem *dlist;
+ struct clk *core_clk;
+
/* Memory manager for CRTCs to allocate space in the display
* list. Units are dwords.
*/
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 836d8799d79e..abdb43c4cc10 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -19,6 +19,7 @@
* each CRTC.
*/
+#include <linux/clk.h>
#include <linux/component.h>
#include <linux/platform_device.h>
@@ -540,6 +541,20 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
hvs->regset.regs = hvs_regs;
hvs->regset.nregs = ARRAY_SIZE(hvs_regs);
+ if (hvs->hvs5) {
+ hvs->core_clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(hvs->core_clk)) {
+ dev_err(&pdev->dev, "Couldn't get core clock\n");
+ return PTR_ERR(hvs->core_clk);
+ }
+
+ ret = clk_prepare_enable(hvs->core_clk);
+ if (ret) {
+ dev_err(&pdev->dev, "Couldn't enable the core clock\n");
+ return ret;
+ }
+ }
+
if (!hvs->hvs5)
hvs->dlist = hvs->regs + SCALER_DLIST_START;
else
@@ -624,6 +639,7 @@ static void vc4_hvs_unbind(struct device *dev, struct device *master,
{
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
+ struct vc4_hvs *hvs = vc4->hvs;
if (drm_mm_node_allocated(&vc4->hvs->mitchell_netravali_filter))
drm_mm_remove_node(&vc4->hvs->mitchell_netravali_filter);
@@ -631,6 +647,8 @@ static void vc4_hvs_unbind(struct device *dev, struct device *master,
drm_mm_takedown(&vc4->hvs->dlist_mm);
drm_mm_takedown(&vc4->hvs->lbm_mm);
+ clk_disable_unprepare(hvs->core_clk);
+
vc4->hvs = NULL;
}
diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index 08318e69061b..210cc2408087 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -11,6 +11,8 @@
* crtc, HDMI encoder).
*/
+#include <linux/clk.h>
+
#include <drm/drm_atomic.h>
#include <drm/drm_atomic_helper.h>
#include <drm/drm_crtc.h>
@@ -149,6 +151,7 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
{
struct drm_device *dev = state->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hvs *hvs = vc4->hvs;
struct vc4_crtc *vc4_crtc;
int i;
@@ -160,6 +163,9 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
vc4_hvs_mask_underrun(dev, vc4_crtc->channel);
}
+ if (vc4->hvs->hvs5)
+ clk_set_min_rate(hvs->core_clk, 500000000);
+
drm_atomic_helper_wait_for_fences(dev, state, false);
drm_atomic_helper_wait_for_dependencies(state);
@@ -182,6 +188,9 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
drm_atomic_helper_commit_cleanup_done(state);
+ if (vc4->hvs->hvs5)
+ clk_set_min_rate(hvs->core_clk, 0);
+
drm_atomic_state_put(state);
up(&vc4->async_modeset);
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 03/80] drm/vc4: hvs: Boost the core clock during modeset
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to prevent timeouts and stalls in the pipeline, the core clock
needs to be maxed at 500MHz during a modeset on the BCM2711.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 2 ++
drivers/gpu/drm/vc4/vc4_hvs.c | 18 ++++++++++++++++++
drivers/gpu/drm/vc4/vc4_kms.c | 9 +++++++++
3 files changed, 29 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index e4cde1f9224b..6358f6ca8d56 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -320,6 +320,8 @@ struct vc4_hvs {
void __iomem *regs;
u32 __iomem *dlist;
+ struct clk *core_clk;
+
/* Memory manager for CRTCs to allocate space in the display
* list. Units are dwords.
*/
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 836d8799d79e..abdb43c4cc10 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -19,6 +19,7 @@
* each CRTC.
*/
+#include <linux/clk.h>
#include <linux/component.h>
#include <linux/platform_device.h>
@@ -540,6 +541,20 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
hvs->regset.regs = hvs_regs;
hvs->regset.nregs = ARRAY_SIZE(hvs_regs);
+ if (hvs->hvs5) {
+ hvs->core_clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(hvs->core_clk)) {
+ dev_err(&pdev->dev, "Couldn't get core clock\n");
+ return PTR_ERR(hvs->core_clk);
+ }
+
+ ret = clk_prepare_enable(hvs->core_clk);
+ if (ret) {
+ dev_err(&pdev->dev, "Couldn't enable the core clock\n");
+ return ret;
+ }
+ }
+
if (!hvs->hvs5)
hvs->dlist = hvs->regs + SCALER_DLIST_START;
else
@@ -624,6 +639,7 @@ static void vc4_hvs_unbind(struct device *dev, struct device *master,
{
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
+ struct vc4_hvs *hvs = vc4->hvs;
if (drm_mm_node_allocated(&vc4->hvs->mitchell_netravali_filter))
drm_mm_remove_node(&vc4->hvs->mitchell_netravali_filter);
@@ -631,6 +647,8 @@ static void vc4_hvs_unbind(struct device *dev, struct device *master,
drm_mm_takedown(&vc4->hvs->dlist_mm);
drm_mm_takedown(&vc4->hvs->lbm_mm);
+ clk_disable_unprepare(hvs->core_clk);
+
vc4->hvs = NULL;
}
diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index 08318e69061b..210cc2408087 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -11,6 +11,8 @@
* crtc, HDMI encoder).
*/
+#include <linux/clk.h>
+
#include <drm/drm_atomic.h>
#include <drm/drm_atomic_helper.h>
#include <drm/drm_crtc.h>
@@ -149,6 +151,7 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
{
struct drm_device *dev = state->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hvs *hvs = vc4->hvs;
struct vc4_crtc *vc4_crtc;
int i;
@@ -160,6 +163,9 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
vc4_hvs_mask_underrun(dev, vc4_crtc->channel);
}
+ if (vc4->hvs->hvs5)
+ clk_set_min_rate(hvs->core_clk, 500000000);
+
drm_atomic_helper_wait_for_fences(dev, state, false);
drm_atomic_helper_wait_for_dependencies(state);
@@ -182,6 +188,9 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
drm_atomic_helper_commit_cleanup_done(state);
+ if (vc4->hvs->hvs5)
+ clk_set_min_rate(hvs->core_clk, 0);
+
drm_atomic_state_put(state);
up(&vc4->async_modeset);
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 04/80] drm/vc4: plane: Change LBM alignment constraint on LBM
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HVS5 needs an alignment of 64bytes for its LBM memory, so let's reflect
it.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index 20c949b57827..d0771ebd5f75 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -578,7 +578,9 @@ static int vc4_plane_allocate_lbm(struct drm_plane_state *state)
spin_lock_irqsave(&vc4->hvs->mm_lock, irqflags);
ret = drm_mm_insert_node_generic(&vc4->hvs->lbm_mm,
&vc4_state->lbm,
- lbm_size, 32, 0, 0);
+ lbm_size,
+ vc4->hvs->hvs5 ? 64 : 32,
+ 0, 0);
spin_unlock_irqrestore(&vc4->hvs->mm_lock, irqflags);
if (ret)
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 04/80] drm/vc4: plane: Change LBM alignment constraint on LBM
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HVS5 needs an alignment of 64bytes for its LBM memory, so let's reflect
it.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index 20c949b57827..d0771ebd5f75 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -578,7 +578,9 @@ static int vc4_plane_allocate_lbm(struct drm_plane_state *state)
spin_lock_irqsave(&vc4->hvs->mm_lock, irqflags);
ret = drm_mm_insert_node_generic(&vc4->hvs->lbm_mm,
&vc4_state->lbm,
- lbm_size, 32, 0, 0);
+ lbm_size,
+ vc4->hvs->hvs5 ? 64 : 32,
+ 0, 0);
spin_unlock_irqrestore(&vc4->hvs->mm_lock, irqflags);
if (ret)
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 04/80] drm/vc4: plane: Change LBM alignment constraint on LBM
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HVS5 needs an alignment of 64bytes for its LBM memory, so let's reflect
it.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index 20c949b57827..d0771ebd5f75 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -578,7 +578,9 @@ static int vc4_plane_allocate_lbm(struct drm_plane_state *state)
spin_lock_irqsave(&vc4->hvs->mm_lock, irqflags);
ret = drm_mm_insert_node_generic(&vc4->hvs->lbm_mm,
&vc4_state->lbm,
- lbm_size, 32, 0, 0);
+ lbm_size,
+ vc4->hvs->hvs5 ? 64 : 32,
+ 0, 0);
spin_unlock_irqrestore(&vc4->hvs->mm_lock, irqflags);
if (ret)
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 05/80] drm/vc4: plane: Optimize the LBM allocation size
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
The current code is using the maximum of the source line size and the
destination line size to compute the size of the LBM to allocate.
While this is simpler, it starts to be an issue with modes such as 4k with
a quite long that will consume all the available memory, so we no longer
have that luxury.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 17 +++++++++++++----
1 file changed, 13 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index d0771ebd5f75..23916814b4e3 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -437,10 +437,7 @@ static void vc4_write_ppf(struct vc4_plane_state *vc4_state, u32 src, u32 dst)
static u32 vc4_lbm_size(struct drm_plane_state *state)
{
struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
- /* This is the worst case number. One of the two sizes will
- * be used depending on the scaling configuration.
- */
- u32 pix_per_line = max(vc4_state->src_w[0], (u32)vc4_state->crtc_w);
+ u32 pix_per_line;
u32 lbm;
/* LBM is not needed when there's no vertical scaling. */
@@ -448,6 +445,18 @@ static u32 vc4_lbm_size(struct drm_plane_state *state)
vc4_state->y_scaling[1] == VC4_SCALING_NONE)
return 0;
+ /*
+ * This can be further optimized in the RGB/YUV444 case if the PPF
+ * decimation factor is between 0.5 and 1.0 by using crtc_w.
+ *
+ * It's not an issue though, since in that case since src_w[0] is going
+ * to be greater than or equal to crtc_w.
+ */
+ if (vc4_state->x_scaling[0] == VC4_SCALING_TPZ)
+ pix_per_line = vc4_state->crtc_w;
+ else
+ pix_per_line = vc4_state->src_w[0];
+
if (!vc4_state->is_yuv) {
if (vc4_state->y_scaling[0] == VC4_SCALING_TPZ)
lbm = pix_per_line * 8;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 05/80] drm/vc4: plane: Optimize the LBM allocation size
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
The current code is using the maximum of the source line size and the
destination line size to compute the size of the LBM to allocate.
While this is simpler, it starts to be an issue with modes such as 4k with
a quite long that will consume all the available memory, so we no longer
have that luxury.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 17 +++++++++++++----
1 file changed, 13 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index d0771ebd5f75..23916814b4e3 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -437,10 +437,7 @@ static void vc4_write_ppf(struct vc4_plane_state *vc4_state, u32 src, u32 dst)
static u32 vc4_lbm_size(struct drm_plane_state *state)
{
struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
- /* This is the worst case number. One of the two sizes will
- * be used depending on the scaling configuration.
- */
- u32 pix_per_line = max(vc4_state->src_w[0], (u32)vc4_state->crtc_w);
+ u32 pix_per_line;
u32 lbm;
/* LBM is not needed when there's no vertical scaling. */
@@ -448,6 +445,18 @@ static u32 vc4_lbm_size(struct drm_plane_state *state)
vc4_state->y_scaling[1] == VC4_SCALING_NONE)
return 0;
+ /*
+ * This can be further optimized in the RGB/YUV444 case if the PPF
+ * decimation factor is between 0.5 and 1.0 by using crtc_w.
+ *
+ * It's not an issue though, since in that case since src_w[0] is going
+ * to be greater than or equal to crtc_w.
+ */
+ if (vc4_state->x_scaling[0] == VC4_SCALING_TPZ)
+ pix_per_line = vc4_state->crtc_w;
+ else
+ pix_per_line = vc4_state->src_w[0];
+
if (!vc4_state->is_yuv) {
if (vc4_state->y_scaling[0] == VC4_SCALING_TPZ)
lbm = pix_per_line * 8;
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 05/80] drm/vc4: plane: Optimize the LBM allocation size
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
The current code is using the maximum of the source line size and the
destination line size to compute the size of the LBM to allocate.
While this is simpler, it starts to be an issue with modes such as 4k with
a quite long that will consume all the available memory, so we no longer
have that luxury.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 17 +++++++++++++----
1 file changed, 13 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index d0771ebd5f75..23916814b4e3 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -437,10 +437,7 @@ static void vc4_write_ppf(struct vc4_plane_state *vc4_state, u32 src, u32 dst)
static u32 vc4_lbm_size(struct drm_plane_state *state)
{
struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
- /* This is the worst case number. One of the two sizes will
- * be used depending on the scaling configuration.
- */
- u32 pix_per_line = max(vc4_state->src_w[0], (u32)vc4_state->crtc_w);
+ u32 pix_per_line;
u32 lbm;
/* LBM is not needed when there's no vertical scaling. */
@@ -448,6 +445,18 @@ static u32 vc4_lbm_size(struct drm_plane_state *state)
vc4_state->y_scaling[1] == VC4_SCALING_NONE)
return 0;
+ /*
+ * This can be further optimized in the RGB/YUV444 case if the PPF
+ * decimation factor is between 0.5 and 1.0 by using crtc_w.
+ *
+ * It's not an issue though, since in that case since src_w[0] is going
+ * to be greater than or equal to crtc_w.
+ */
+ if (vc4_state->x_scaling[0] == VC4_SCALING_TPZ)
+ pix_per_line = vc4_state->crtc_w;
+ else
+ pix_per_line = vc4_state->src_w[0];
+
if (!vc4_state->is_yuv) {
if (vc4_state->y_scaling[0] == VC4_SCALING_TPZ)
lbm = pix_per_line * 8;
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 06/80] drm/vc4: plane: Create more planes
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Let's now create more planes that can be affected to all the CRTCs.
vc4 has 3 CRTCs, 1 primary and 1 cursor each, and was having 24 (8
planes per CRTC) overlays.
However, vc5 has 5 CRTCs, so keeping the same logic would put us at 50
planes which is well above the 32 planes limit imposed by DRM.
Using 16 seems like a good tradeoff between staying under 32 and yet
providing enough planes.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index 23916814b4e3..1e38e603f83b 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -1384,7 +1384,7 @@ int vc4_plane_create_additional_planes(struct drm_device *drm)
* modest number of planes to expose, that should hopefully
* still cover any sane usecase.
*/
- for (i = 0; i < 8; i++) {
+ for (i = 0; i < 16; i++) {
struct drm_plane *plane =
vc4_plane_init(drm, DRM_PLANE_TYPE_OVERLAY);
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 06/80] drm/vc4: plane: Create more planes
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Let's now create more planes that can be affected to all the CRTCs.
vc4 has 3 CRTCs, 1 primary and 1 cursor each, and was having 24 (8
planes per CRTC) overlays.
However, vc5 has 5 CRTCs, so keeping the same logic would put us at 50
planes which is well above the 32 planes limit imposed by DRM.
Using 16 seems like a good tradeoff between staying under 32 and yet
providing enough planes.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index 23916814b4e3..1e38e603f83b 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -1384,7 +1384,7 @@ int vc4_plane_create_additional_planes(struct drm_device *drm)
* modest number of planes to expose, that should hopefully
* still cover any sane usecase.
*/
- for (i = 0; i < 8; i++) {
+ for (i = 0; i < 16; i++) {
struct drm_plane *plane =
vc4_plane_init(drm, DRM_PLANE_TYPE_OVERLAY);
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 06/80] drm/vc4: plane: Create more planes
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Let's now create more planes that can be affected to all the CRTCs.
vc4 has 3 CRTCs, 1 primary and 1 cursor each, and was having 24 (8
planes per CRTC) overlays.
However, vc5 has 5 CRTCs, so keeping the same logic would put us at 50
planes which is well above the 32 planes limit imposed by DRM.
Using 16 seems like a good tradeoff between staying under 32 and yet
providing enough planes.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_plane.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_plane.c b/drivers/gpu/drm/vc4/vc4_plane.c
index 23916814b4e3..1e38e603f83b 100644
--- a/drivers/gpu/drm/vc4/vc4_plane.c
+++ b/drivers/gpu/drm/vc4/vc4_plane.c
@@ -1384,7 +1384,7 @@ int vc4_plane_create_additional_planes(struct drm_device *drm)
* modest number of planes to expose, that should hopefully
* still cover any sane usecase.
*/
- for (i = 0; i < 8; i++) {
+ for (i = 0; i < 16; i++) {
struct drm_plane *plane =
vc4_plane_init(drm, DRM_PLANE_TYPE_OVERLAY);
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 07/80] drm/vc4: crtc: Deal with different number of pixel per clock
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Some of the HDMI pixelvalves in vc5 output two pixels per clock cycle.
Let's put the number of pixel output per clock cycle in the CRTC data and
update the various calculations to reflect that.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 18 +++++++++++-------
drivers/gpu/drm/vc4/vc4_drv.h | 3 +++
2 files changed, 14 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 6d8fa6118fc1..e55b2208b4b7 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -235,6 +235,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc);
struct drm_crtc_state *state = crtc->state;
struct drm_display_mode *mode = &state->adjusted_mode;
bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
@@ -242,6 +243,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 ||
vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
+ u8 ppc = pv_data->pixels_per_clock;
/* Reset the PV fifo. */
CRTC_WRITE(PV_CONTROL, 0);
@@ -249,17 +251,16 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
CRTC_WRITE(PV_CONTROL, 0);
CRTC_WRITE(PV_HORZA,
- VC4_SET_FIELD((mode->htotal -
- mode->hsync_end) * pixel_rep,
+ VC4_SET_FIELD((mode->htotal - mode->hsync_end) * pixel_rep / ppc,
PV_HORZA_HBP) |
- VC4_SET_FIELD((mode->hsync_end -
- mode->hsync_start) * pixel_rep,
+ VC4_SET_FIELD((mode->hsync_end - mode->hsync_start) * pixel_rep / ppc,
PV_HORZA_HSYNC));
+
CRTC_WRITE(PV_HORZB,
- VC4_SET_FIELD((mode->hsync_start -
- mode->hdisplay) * pixel_rep,
+ VC4_SET_FIELD((mode->hsync_start - mode->hdisplay) * pixel_rep / ppc,
PV_HORZB_HFP) |
- VC4_SET_FIELD(mode->hdisplay * pixel_rep, PV_HORZB_HACTIVE));
+ VC4_SET_FIELD(mode->hdisplay * pixel_rep / ppc,
+ PV_HORZB_HACTIVE));
CRTC_WRITE(PV_VERTA,
VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end,
@@ -761,6 +762,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
.hvs_channel = 0,
},
.debugfs_name = "crtc0_regs",
+ .pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI0,
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_DPI,
@@ -772,6 +774,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
.hvs_channel = 2,
},
.debugfs_name = "crtc1_regs",
+ .pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI1,
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_SMI,
@@ -783,6 +786,7 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
.hvs_channel = 1,
},
.debugfs_name = "crtc2_regs",
+ .pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI,
[PV_CONTROL_CLK_SELECT_VEC] = VC4_ENCODER_TYPE_VEC,
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 6358f6ca8d56..0bc150daafb2 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -454,6 +454,9 @@ struct vc4_crtc_data {
struct vc4_pv_data {
struct vc4_crtc_data base;
+ /* Number of pixels output per clock period */
+ u8 pixels_per_clock;
+
enum vc4_encoder_type encoder_types[4];
const char *debugfs_name;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 07/80] drm/vc4: crtc: Deal with different number of pixel per clock
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Some of the HDMI pixelvalves in vc5 output two pixels per clock cycle.
Let's put the number of pixel output per clock cycle in the CRTC data and
update the various calculations to reflect that.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 18 +++++++++++-------
drivers/gpu/drm/vc4/vc4_drv.h | 3 +++
2 files changed, 14 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 6d8fa6118fc1..e55b2208b4b7 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -235,6 +235,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc);
struct drm_crtc_state *state = crtc->state;
struct drm_display_mode *mode = &state->adjusted_mode;
bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
@@ -242,6 +243,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 ||
vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
+ u8 ppc = pv_data->pixels_per_clock;
/* Reset the PV fifo. */
CRTC_WRITE(PV_CONTROL, 0);
@@ -249,17 +251,16 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
CRTC_WRITE(PV_CONTROL, 0);
CRTC_WRITE(PV_HORZA,
- VC4_SET_FIELD((mode->htotal -
- mode->hsync_end) * pixel_rep,
+ VC4_SET_FIELD((mode->htotal - mode->hsync_end) * pixel_rep / ppc,
PV_HORZA_HBP) |
- VC4_SET_FIELD((mode->hsync_end -
- mode->hsync_start) * pixel_rep,
+ VC4_SET_FIELD((mode->hsync_end - mode->hsync_start) * pixel_rep / ppc,
PV_HORZA_HSYNC));
+
CRTC_WRITE(PV_HORZB,
- VC4_SET_FIELD((mode->hsync_start -
- mode->hdisplay) * pixel_rep,
+ VC4_SET_FIELD((mode->hsync_start - mode->hdisplay) * pixel_rep / ppc,
PV_HORZB_HFP) |
- VC4_SET_FIELD(mode->hdisplay * pixel_rep, PV_HORZB_HACTIVE));
+ VC4_SET_FIELD(mode->hdisplay * pixel_rep / ppc,
+ PV_HORZB_HACTIVE));
CRTC_WRITE(PV_VERTA,
VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end,
@@ -761,6 +762,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
.hvs_channel = 0,
},
.debugfs_name = "crtc0_regs",
+ .pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI0,
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_DPI,
@@ -772,6 +774,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
.hvs_channel = 2,
},
.debugfs_name = "crtc1_regs",
+ .pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI1,
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_SMI,
@@ -783,6 +786,7 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
.hvs_channel = 1,
},
.debugfs_name = "crtc2_regs",
+ .pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI,
[PV_CONTROL_CLK_SELECT_VEC] = VC4_ENCODER_TYPE_VEC,
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 6358f6ca8d56..0bc150daafb2 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -454,6 +454,9 @@ struct vc4_crtc_data {
struct vc4_pv_data {
struct vc4_crtc_data base;
+ /* Number of pixels output per clock period */
+ u8 pixels_per_clock;
+
enum vc4_encoder_type encoder_types[4];
const char *debugfs_name;
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 07/80] drm/vc4: crtc: Deal with different number of pixel per clock
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Some of the HDMI pixelvalves in vc5 output two pixels per clock cycle.
Let's put the number of pixel output per clock cycle in the CRTC data and
update the various calculations to reflect that.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 18 +++++++++++-------
drivers/gpu/drm/vc4/vc4_drv.h | 3 +++
2 files changed, 14 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 6d8fa6118fc1..e55b2208b4b7 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -235,6 +235,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc);
struct drm_crtc_state *state = crtc->state;
struct drm_display_mode *mode = &state->adjusted_mode;
bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
@@ -242,6 +243,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 ||
vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
+ u8 ppc = pv_data->pixels_per_clock;
/* Reset the PV fifo. */
CRTC_WRITE(PV_CONTROL, 0);
@@ -249,17 +251,16 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
CRTC_WRITE(PV_CONTROL, 0);
CRTC_WRITE(PV_HORZA,
- VC4_SET_FIELD((mode->htotal -
- mode->hsync_end) * pixel_rep,
+ VC4_SET_FIELD((mode->htotal - mode->hsync_end) * pixel_rep / ppc,
PV_HORZA_HBP) |
- VC4_SET_FIELD((mode->hsync_end -
- mode->hsync_start) * pixel_rep,
+ VC4_SET_FIELD((mode->hsync_end - mode->hsync_start) * pixel_rep / ppc,
PV_HORZA_HSYNC));
+
CRTC_WRITE(PV_HORZB,
- VC4_SET_FIELD((mode->hsync_start -
- mode->hdisplay) * pixel_rep,
+ VC4_SET_FIELD((mode->hsync_start - mode->hdisplay) * pixel_rep / ppc,
PV_HORZB_HFP) |
- VC4_SET_FIELD(mode->hdisplay * pixel_rep, PV_HORZB_HACTIVE));
+ VC4_SET_FIELD(mode->hdisplay * pixel_rep / ppc,
+ PV_HORZB_HACTIVE));
CRTC_WRITE(PV_VERTA,
VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end,
@@ -761,6 +762,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
.hvs_channel = 0,
},
.debugfs_name = "crtc0_regs",
+ .pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI0,
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_DPI,
@@ -772,6 +774,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
.hvs_channel = 2,
},
.debugfs_name = "crtc1_regs",
+ .pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI1,
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_SMI,
@@ -783,6 +786,7 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
.hvs_channel = 1,
},
.debugfs_name = "crtc2_regs",
+ .pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI,
[PV_CONTROL_CLK_SELECT_VEC] = VC4_ENCODER_TYPE_VEC,
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 6358f6ca8d56..0bc150daafb2 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -454,6 +454,9 @@ struct vc4_crtc_data {
struct vc4_pv_data {
struct vc4_crtc_data base;
+ /* Number of pixels output per clock period */
+ u8 pixels_per_clock;
+
enum vc4_encoder_type encoder_types[4];
const char *debugfs_name;
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 08/80] drm/vc4: crtc: Use a shared interrupt
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Some pixelvalves in vc5 use the same interrupt line so let's register our
interrupt handler as a shared one.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index e55b2208b4b7..9faae22cb0f8 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -919,7 +919,9 @@ static int vc4_crtc_bind(struct device *dev, struct device *master, void *data)
CRTC_WRITE(PV_INTEN, 0);
CRTC_WRITE(PV_INTSTAT, PV_INT_VFP_START);
ret = devm_request_irq(dev, platform_get_irq(pdev, 0),
- vc4_crtc_irq_handler, 0, "vc4 crtc", vc4_crtc);
+ vc4_crtc_irq_handler,
+ IRQF_SHARED,
+ "vc4 crtc", vc4_crtc);
if (ret)
goto err_destroy_planes;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 08/80] drm/vc4: crtc: Use a shared interrupt
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Some pixelvalves in vc5 use the same interrupt line so let's register our
interrupt handler as a shared one.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index e55b2208b4b7..9faae22cb0f8 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -919,7 +919,9 @@ static int vc4_crtc_bind(struct device *dev, struct device *master, void *data)
CRTC_WRITE(PV_INTEN, 0);
CRTC_WRITE(PV_INTSTAT, PV_INT_VFP_START);
ret = devm_request_irq(dev, platform_get_irq(pdev, 0),
- vc4_crtc_irq_handler, 0, "vc4 crtc", vc4_crtc);
+ vc4_crtc_irq_handler,
+ IRQF_SHARED,
+ "vc4 crtc", vc4_crtc);
if (ret)
goto err_destroy_planes;
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 08/80] drm/vc4: crtc: Use a shared interrupt
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Some pixelvalves in vc5 use the same interrupt line so let's register our
interrupt handler as a shared one.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index e55b2208b4b7..9faae22cb0f8 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -919,7 +919,9 @@ static int vc4_crtc_bind(struct device *dev, struct device *master, void *data)
CRTC_WRITE(PV_INTEN, 0);
CRTC_WRITE(PV_INTSTAT, PV_INT_VFP_START);
ret = devm_request_irq(dev, platform_get_irq(pdev, 0),
- vc4_crtc_irq_handler, 0, "vc4 crtc", vc4_crtc);
+ vc4_crtc_irq_handler,
+ IRQF_SHARED,
+ "vc4 crtc", vc4_crtc);
if (ret)
goto err_destroy_planes;
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 09/80] drm/vc4: crtc: Move the cob allocation outside of bind
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The COB allocation depends on the HVS channel used for a given
pixelvalve.
While the channel allocation was entirely static in vc4, vc5 changes
that and at bind time, a pixelvalve can be assigned to multiple
HVS channels.
Let's prepare that rework by allocating the COB when it's actually
needed.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 35 +++++++++++++++++------------------
drivers/gpu/drm/vc4/vc4_drv.h | 2 +--
2 files changed, 17 insertions(+), 20 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 9faae22cb0f8..fdecaba77836 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -65,6 +65,20 @@ static const struct debugfs_reg32 crtc_regs[] = {
VC4_REG32(PV_HACT_ACT),
};
+static unsigned int
+vc4_crtc_get_cob_allocation(struct vc4_dev *vc4, unsigned int channel)
+{
+ u32 dispbase = HVS_READ(SCALER_DISPBASEX(channel));
+ /* Top/base are supposed to be 4-pixel aligned, but the
+ * Raspberry Pi firmware fills the low bits (which are
+ * presumably ignored).
+ */
+ u32 top = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_TOP) & ~3;
+ u32 base = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_BASE) & ~3;
+
+ return top - base + 4;
+}
+
static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
bool in_vblank_irq,
int *vpos, int *hpos,
@@ -74,6 +88,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ unsigned int cob_size;
u32 val;
int fifo_lines;
int vblank_lines;
@@ -109,8 +124,9 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
*hpos += mode->crtc_htotal / 2;
}
+ cob_size = vc4_crtc_get_cob_allocation(vc4, vc4_crtc->channel);
/* This is the offset we need for translating hvs -> pv scanout pos. */
- fifo_lines = vc4_crtc->cob_size / mode->crtc_hdisplay;
+ fifo_lines = cob_size / mode->crtc_hdisplay;
if (fifo_lines > 0)
ret = true;
@@ -823,22 +839,6 @@ static void vc4_set_crtc_possible_masks(struct drm_device *drm,
}
}
-static void
-vc4_crtc_get_cob_allocation(struct vc4_crtc *vc4_crtc)
-{
- struct drm_device *drm = vc4_crtc->base.dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
- u32 dispbase = HVS_READ(SCALER_DISPBASEX(vc4_crtc->channel));
- /* Top/base are supposed to be 4-pixel aligned, but the
- * Raspberry Pi firmware fills the low bits (which are
- * presumably ignored).
- */
- u32 top = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_TOP) & ~3;
- u32 base = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_BASE) & ~3;
-
- vc4_crtc->cob_size = top - base + 4;
-}
-
int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
const struct drm_crtc_funcs *crtc_funcs,
const struct drm_crtc_helper_funcs *crtc_helper_funcs)
@@ -870,7 +870,6 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
* implemented as private driver state in vc4_kms, not here.
*/
drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size);
- vc4_crtc_get_cob_allocation(vc4_crtc);
for (i = 0; i < crtc->gamma_size; i++) {
vc4_crtc->lut_r[i] = i;
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 0bc150daafb2..d80fc3bbb450 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -477,8 +477,6 @@ struct vc4_crtc {
u8 lut_r[256];
u8 lut_g[256];
u8 lut_b[256];
- /* Size in pixels of the COB memory allocated to this CRTC. */
- u32 cob_size;
struct drm_pending_vblank_event *event;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 09/80] drm/vc4: crtc: Move the cob allocation outside of bind
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The COB allocation depends on the HVS channel used for a given
pixelvalve.
While the channel allocation was entirely static in vc4, vc5 changes
that and at bind time, a pixelvalve can be assigned to multiple
HVS channels.
Let's prepare that rework by allocating the COB when it's actually
needed.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 35 +++++++++++++++++------------------
drivers/gpu/drm/vc4/vc4_drv.h | 2 +--
2 files changed, 17 insertions(+), 20 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 9faae22cb0f8..fdecaba77836 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -65,6 +65,20 @@ static const struct debugfs_reg32 crtc_regs[] = {
VC4_REG32(PV_HACT_ACT),
};
+static unsigned int
+vc4_crtc_get_cob_allocation(struct vc4_dev *vc4, unsigned int channel)
+{
+ u32 dispbase = HVS_READ(SCALER_DISPBASEX(channel));
+ /* Top/base are supposed to be 4-pixel aligned, but the
+ * Raspberry Pi firmware fills the low bits (which are
+ * presumably ignored).
+ */
+ u32 top = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_TOP) & ~3;
+ u32 base = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_BASE) & ~3;
+
+ return top - base + 4;
+}
+
static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
bool in_vblank_irq,
int *vpos, int *hpos,
@@ -74,6 +88,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ unsigned int cob_size;
u32 val;
int fifo_lines;
int vblank_lines;
@@ -109,8 +124,9 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
*hpos += mode->crtc_htotal / 2;
}
+ cob_size = vc4_crtc_get_cob_allocation(vc4, vc4_crtc->channel);
/* This is the offset we need for translating hvs -> pv scanout pos. */
- fifo_lines = vc4_crtc->cob_size / mode->crtc_hdisplay;
+ fifo_lines = cob_size / mode->crtc_hdisplay;
if (fifo_lines > 0)
ret = true;
@@ -823,22 +839,6 @@ static void vc4_set_crtc_possible_masks(struct drm_device *drm,
}
}
-static void
-vc4_crtc_get_cob_allocation(struct vc4_crtc *vc4_crtc)
-{
- struct drm_device *drm = vc4_crtc->base.dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
- u32 dispbase = HVS_READ(SCALER_DISPBASEX(vc4_crtc->channel));
- /* Top/base are supposed to be 4-pixel aligned, but the
- * Raspberry Pi firmware fills the low bits (which are
- * presumably ignored).
- */
- u32 top = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_TOP) & ~3;
- u32 base = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_BASE) & ~3;
-
- vc4_crtc->cob_size = top - base + 4;
-}
-
int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
const struct drm_crtc_funcs *crtc_funcs,
const struct drm_crtc_helper_funcs *crtc_helper_funcs)
@@ -870,7 +870,6 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
* implemented as private driver state in vc4_kms, not here.
*/
drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size);
- vc4_crtc_get_cob_allocation(vc4_crtc);
for (i = 0; i < crtc->gamma_size; i++) {
vc4_crtc->lut_r[i] = i;
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 0bc150daafb2..d80fc3bbb450 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -477,8 +477,6 @@ struct vc4_crtc {
u8 lut_r[256];
u8 lut_g[256];
u8 lut_b[256];
- /* Size in pixels of the COB memory allocated to this CRTC. */
- u32 cob_size;
struct drm_pending_vblank_event *event;
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 09/80] drm/vc4: crtc: Move the cob allocation outside of bind
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The COB allocation depends on the HVS channel used for a given
pixelvalve.
While the channel allocation was entirely static in vc4, vc5 changes
that and at bind time, a pixelvalve can be assigned to multiple
HVS channels.
Let's prepare that rework by allocating the COB when it's actually
needed.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 35 +++++++++++++++++------------------
drivers/gpu/drm/vc4/vc4_drv.h | 2 +--
2 files changed, 17 insertions(+), 20 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 9faae22cb0f8..fdecaba77836 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -65,6 +65,20 @@ static const struct debugfs_reg32 crtc_regs[] = {
VC4_REG32(PV_HACT_ACT),
};
+static unsigned int
+vc4_crtc_get_cob_allocation(struct vc4_dev *vc4, unsigned int channel)
+{
+ u32 dispbase = HVS_READ(SCALER_DISPBASEX(channel));
+ /* Top/base are supposed to be 4-pixel aligned, but the
+ * Raspberry Pi firmware fills the low bits (which are
+ * presumably ignored).
+ */
+ u32 top = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_TOP) & ~3;
+ u32 base = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_BASE) & ~3;
+
+ return top - base + 4;
+}
+
static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
bool in_vblank_irq,
int *vpos, int *hpos,
@@ -74,6 +88,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ unsigned int cob_size;
u32 val;
int fifo_lines;
int vblank_lines;
@@ -109,8 +124,9 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
*hpos += mode->crtc_htotal / 2;
}
+ cob_size = vc4_crtc_get_cob_allocation(vc4, vc4_crtc->channel);
/* This is the offset we need for translating hvs -> pv scanout pos. */
- fifo_lines = vc4_crtc->cob_size / mode->crtc_hdisplay;
+ fifo_lines = cob_size / mode->crtc_hdisplay;
if (fifo_lines > 0)
ret = true;
@@ -823,22 +839,6 @@ static void vc4_set_crtc_possible_masks(struct drm_device *drm,
}
}
-static void
-vc4_crtc_get_cob_allocation(struct vc4_crtc *vc4_crtc)
-{
- struct drm_device *drm = vc4_crtc->base.dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
- u32 dispbase = HVS_READ(SCALER_DISPBASEX(vc4_crtc->channel));
- /* Top/base are supposed to be 4-pixel aligned, but the
- * Raspberry Pi firmware fills the low bits (which are
- * presumably ignored).
- */
- u32 top = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_TOP) & ~3;
- u32 base = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_BASE) & ~3;
-
- vc4_crtc->cob_size = top - base + 4;
-}
-
int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
const struct drm_crtc_funcs *crtc_funcs,
const struct drm_crtc_helper_funcs *crtc_helper_funcs)
@@ -870,7 +870,6 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
* implemented as private driver state in vc4_kms, not here.
*/
drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size);
- vc4_crtc_get_cob_allocation(vc4_crtc);
for (i = 0; i < crtc->gamma_size; i++) {
vc4_crtc->lut_r[i] = i;
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 0bc150daafb2..d80fc3bbb450 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -477,8 +477,6 @@ struct vc4_crtc {
u8 lut_r[256];
u8 lut_g[256];
u8 lut_b[256];
- /* Size in pixels of the COB memory allocated to this CRTC. */
- u32 cob_size;
struct drm_pending_vblank_event *event;
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 10/80] drm/vc4: crtc: Rename HVS channel to output
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
In vc5, the HVS has 6 outputs and 3 FIFOs (or channels), with
pixelvalves each being assigned to a given output, but each output can
then be muxed to feed from multiple FIFOs.
Since vc4 had that entirely static, both were probably equivalent, but
since that changes, let's rename hvs_channel to hvs_output in the
vc4_crtc_data, since a pixelvalve is really connected to an output, and
not to a FIFO.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 8 ++++----
drivers/gpu/drm/vc4/vc4_drv.h | 4 ++--
drivers/gpu/drm/vc4/vc4_hvs.c | 2 +-
drivers/gpu/drm/vc4/vc4_txp.c | 2 +-
4 files changed, 8 insertions(+), 8 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index fdecaba77836..d3126fe04d9a 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -775,7 +775,7 @@ static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
static const struct vc4_pv_data bcm2835_pv0_data = {
.base = {
- .hvs_channel = 0,
+ .hvs_output = 0,
},
.debugfs_name = "crtc0_regs",
.pixels_per_clock = 1,
@@ -787,7 +787,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
static const struct vc4_pv_data bcm2835_pv1_data = {
.base = {
- .hvs_channel = 2,
+ .hvs_output = 2,
},
.debugfs_name = "crtc1_regs",
.pixels_per_clock = 1,
@@ -799,7 +799,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
static const struct vc4_pv_data bcm2835_pv2_data = {
.base = {
- .hvs_channel = 1,
+ .hvs_output = 1,
},
.debugfs_name = "crtc2_regs",
.pixels_per_clock = 1,
@@ -862,7 +862,7 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
crtc_funcs, NULL);
drm_crtc_helper_add(crtc, crtc_helper_funcs);
- vc4_crtc->channel = vc4_crtc->data->hvs_channel;
+ vc4_crtc->channel = vc4_crtc->data->hvs_output;
drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index d80fc3bbb450..d1cf4c038180 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -447,8 +447,8 @@ to_vc4_encoder(struct drm_encoder *encoder)
}
struct vc4_crtc_data {
- /* Which channel of the HVS this pixelvalve sources from. */
- int hvs_channel;
+ /* Which output of the HVS this pixelvalve sources from. */
+ int hvs_output;
};
struct vc4_pv_data {
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index abdb43c4cc10..365425d67f3f 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -419,7 +419,7 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
- if (vc4_crtc->data->hvs_channel == 2) {
+ if (vc4_crtc->data->hvs_output == 2) {
u32 dispctrl;
u32 dsp3_mux;
diff --git a/drivers/gpu/drm/vc4/vc4_txp.c b/drivers/gpu/drm/vc4/vc4_txp.c
index a7c3af0005a0..f39d9900d027 100644
--- a/drivers/gpu/drm/vc4/vc4_txp.c
+++ b/drivers/gpu/drm/vc4/vc4_txp.c
@@ -452,7 +452,7 @@ static irqreturn_t vc4_txp_interrupt(int irq, void *data)
}
static const struct vc4_crtc_data vc4_txp_crtc_data = {
- .hvs_channel = 2,
+ .hvs_output = 2,
};
static int vc4_txp_bind(struct device *dev, struct device *master, void *data)
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 10/80] drm/vc4: crtc: Rename HVS channel to output
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In vc5, the HVS has 6 outputs and 3 FIFOs (or channels), with
pixelvalves each being assigned to a given output, but each output can
then be muxed to feed from multiple FIFOs.
Since vc4 had that entirely static, both were probably equivalent, but
since that changes, let's rename hvs_channel to hvs_output in the
vc4_crtc_data, since a pixelvalve is really connected to an output, and
not to a FIFO.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 8 ++++----
drivers/gpu/drm/vc4/vc4_drv.h | 4 ++--
drivers/gpu/drm/vc4/vc4_hvs.c | 2 +-
drivers/gpu/drm/vc4/vc4_txp.c | 2 +-
4 files changed, 8 insertions(+), 8 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index fdecaba77836..d3126fe04d9a 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -775,7 +775,7 @@ static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
static const struct vc4_pv_data bcm2835_pv0_data = {
.base = {
- .hvs_channel = 0,
+ .hvs_output = 0,
},
.debugfs_name = "crtc0_regs",
.pixels_per_clock = 1,
@@ -787,7 +787,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
static const struct vc4_pv_data bcm2835_pv1_data = {
.base = {
- .hvs_channel = 2,
+ .hvs_output = 2,
},
.debugfs_name = "crtc1_regs",
.pixels_per_clock = 1,
@@ -799,7 +799,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
static const struct vc4_pv_data bcm2835_pv2_data = {
.base = {
- .hvs_channel = 1,
+ .hvs_output = 1,
},
.debugfs_name = "crtc2_regs",
.pixels_per_clock = 1,
@@ -862,7 +862,7 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
crtc_funcs, NULL);
drm_crtc_helper_add(crtc, crtc_helper_funcs);
- vc4_crtc->channel = vc4_crtc->data->hvs_channel;
+ vc4_crtc->channel = vc4_crtc->data->hvs_output;
drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index d80fc3bbb450..d1cf4c038180 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -447,8 +447,8 @@ to_vc4_encoder(struct drm_encoder *encoder)
}
struct vc4_crtc_data {
- /* Which channel of the HVS this pixelvalve sources from. */
- int hvs_channel;
+ /* Which output of the HVS this pixelvalve sources from. */
+ int hvs_output;
};
struct vc4_pv_data {
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index abdb43c4cc10..365425d67f3f 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -419,7 +419,7 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
- if (vc4_crtc->data->hvs_channel == 2) {
+ if (vc4_crtc->data->hvs_output == 2) {
u32 dispctrl;
u32 dsp3_mux;
diff --git a/drivers/gpu/drm/vc4/vc4_txp.c b/drivers/gpu/drm/vc4/vc4_txp.c
index a7c3af0005a0..f39d9900d027 100644
--- a/drivers/gpu/drm/vc4/vc4_txp.c
+++ b/drivers/gpu/drm/vc4/vc4_txp.c
@@ -452,7 +452,7 @@ static irqreturn_t vc4_txp_interrupt(int irq, void *data)
}
static const struct vc4_crtc_data vc4_txp_crtc_data = {
- .hvs_channel = 2,
+ .hvs_output = 2,
};
static int vc4_txp_bind(struct device *dev, struct device *master, void *data)
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 10/80] drm/vc4: crtc: Rename HVS channel to output
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In vc5, the HVS has 6 outputs and 3 FIFOs (or channels), with
pixelvalves each being assigned to a given output, but each output can
then be muxed to feed from multiple FIFOs.
Since vc4 had that entirely static, both were probably equivalent, but
since that changes, let's rename hvs_channel to hvs_output in the
vc4_crtc_data, since a pixelvalve is really connected to an output, and
not to a FIFO.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 8 ++++----
drivers/gpu/drm/vc4/vc4_drv.h | 4 ++--
drivers/gpu/drm/vc4/vc4_hvs.c | 2 +-
drivers/gpu/drm/vc4/vc4_txp.c | 2 +-
4 files changed, 8 insertions(+), 8 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index fdecaba77836..d3126fe04d9a 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -775,7 +775,7 @@ static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
static const struct vc4_pv_data bcm2835_pv0_data = {
.base = {
- .hvs_channel = 0,
+ .hvs_output = 0,
},
.debugfs_name = "crtc0_regs",
.pixels_per_clock = 1,
@@ -787,7 +787,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
static const struct vc4_pv_data bcm2835_pv1_data = {
.base = {
- .hvs_channel = 2,
+ .hvs_output = 2,
},
.debugfs_name = "crtc1_regs",
.pixels_per_clock = 1,
@@ -799,7 +799,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
static const struct vc4_pv_data bcm2835_pv2_data = {
.base = {
- .hvs_channel = 1,
+ .hvs_output = 1,
},
.debugfs_name = "crtc2_regs",
.pixels_per_clock = 1,
@@ -862,7 +862,7 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
crtc_funcs, NULL);
drm_crtc_helper_add(crtc, crtc_helper_funcs);
- vc4_crtc->channel = vc4_crtc->data->hvs_channel;
+ vc4_crtc->channel = vc4_crtc->data->hvs_output;
drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index d80fc3bbb450..d1cf4c038180 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -447,8 +447,8 @@ to_vc4_encoder(struct drm_encoder *encoder)
}
struct vc4_crtc_data {
- /* Which channel of the HVS this pixelvalve sources from. */
- int hvs_channel;
+ /* Which output of the HVS this pixelvalve sources from. */
+ int hvs_output;
};
struct vc4_pv_data {
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index abdb43c4cc10..365425d67f3f 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -419,7 +419,7 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
- if (vc4_crtc->data->hvs_channel == 2) {
+ if (vc4_crtc->data->hvs_output == 2) {
u32 dispctrl;
u32 dsp3_mux;
diff --git a/drivers/gpu/drm/vc4/vc4_txp.c b/drivers/gpu/drm/vc4/vc4_txp.c
index a7c3af0005a0..f39d9900d027 100644
--- a/drivers/gpu/drm/vc4/vc4_txp.c
+++ b/drivers/gpu/drm/vc4/vc4_txp.c
@@ -452,7 +452,7 @@ static irqreturn_t vc4_txp_interrupt(int irq, void *data)
}
static const struct vc4_crtc_data vc4_txp_crtc_data = {
- .hvs_channel = 2,
+ .hvs_output = 2,
};
static int vc4_txp_bind(struct device *dev, struct device *master, void *data)
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 11/80] drm/vc4: crtc: Use local chan variable
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The vc4_crtc_handle_page_flip already has a local variable holding the
value of vc4_crtc->channel, so let's use it instead.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index d3126fe04d9a..cdeaa0cd981f 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -533,7 +533,7 @@ static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc)
* the CRTC and encoder already reconfigured, leading to
* underruns. This can be seen when reconfiguring the CRTC.
*/
- vc4_hvs_unmask_underrun(dev, vc4_crtc->channel);
+ vc4_hvs_unmask_underrun(dev, chan);
}
spin_unlock_irqrestore(&dev->event_lock, flags);
}
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 11/80] drm/vc4: crtc: Use local chan variable
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The vc4_crtc_handle_page_flip already has a local variable holding the
value of vc4_crtc->channel, so let's use it instead.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index d3126fe04d9a..cdeaa0cd981f 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -533,7 +533,7 @@ static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc)
* the CRTC and encoder already reconfigured, leading to
* underruns. This can be seen when reconfiguring the CRTC.
*/
- vc4_hvs_unmask_underrun(dev, vc4_crtc->channel);
+ vc4_hvs_unmask_underrun(dev, chan);
}
spin_unlock_irqrestore(&dev->event_lock, flags);
}
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 11/80] drm/vc4: crtc: Use local chan variable
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The vc4_crtc_handle_page_flip already has a local variable holding the
value of vc4_crtc->channel, so let's use it instead.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index d3126fe04d9a..cdeaa0cd981f 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -533,7 +533,7 @@ static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc)
* the CRTC and encoder already reconfigured, leading to
* underruns. This can be seen when reconfiguring the CRTC.
*/
- vc4_hvs_unmask_underrun(dev, vc4_crtc->channel);
+ vc4_hvs_unmask_underrun(dev, chan);
}
spin_unlock_irqrestore(&dev->event_lock, flags);
}
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 12/80] drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The VIDEN bit in the pixelvalve currently being used to enable or disable
the pixelvalve seems to not be enough in some situations, which whill end
up with the pixelvalve stalling.
In such a case, even re-enabling VIDEN doesn't bring it back and we need to
clear the FIFO. This can only be done if the pixelvalve is disabled though.
In order to overcome this, we can configure the pixelvalve during
mode_set_no_fb by calling vc4_crtc_config_pv, but only enable it in
atomic_enable and flush the FIFO there, and in atomic_disable disable the
pixelvalve again.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 10 +++++++---
1 file changed, 7 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index cdeaa0cd981f..fe2e5675aed4 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -332,9 +332,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
PV_CONTROL_TRIGGER_UNDERFLOW |
PV_CONTROL_WAIT_HSTART |
VC4_SET_FIELD(vc4_encoder->clock_select,
- PV_CONTROL_CLK_SELECT) |
- PV_CONTROL_FIFO_CLR |
- PV_CONTROL_EN);
+ PV_CONTROL_CLK_SELECT));
}
static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
@@ -386,6 +384,8 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n");
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
+
vc4_hvs_atomic_disable(crtc, old_state);
/*
@@ -410,6 +410,10 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
+ /* Reset the PV fifo. */
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) |
+ PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);
+
/* Enable vblank irq handling before crtc is started otherwise
* drm_crtc_get_vblank() fails in vc4_crtc_update_dlist().
*/
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 12/80] drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The VIDEN bit in the pixelvalve currently being used to enable or disable
the pixelvalve seems to not be enough in some situations, which whill end
up with the pixelvalve stalling.
In such a case, even re-enabling VIDEN doesn't bring it back and we need to
clear the FIFO. This can only be done if the pixelvalve is disabled though.
In order to overcome this, we can configure the pixelvalve during
mode_set_no_fb by calling vc4_crtc_config_pv, but only enable it in
atomic_enable and flush the FIFO there, and in atomic_disable disable the
pixelvalve again.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 10 +++++++---
1 file changed, 7 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index cdeaa0cd981f..fe2e5675aed4 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -332,9 +332,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
PV_CONTROL_TRIGGER_UNDERFLOW |
PV_CONTROL_WAIT_HSTART |
VC4_SET_FIELD(vc4_encoder->clock_select,
- PV_CONTROL_CLK_SELECT) |
- PV_CONTROL_FIFO_CLR |
- PV_CONTROL_EN);
+ PV_CONTROL_CLK_SELECT));
}
static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
@@ -386,6 +384,8 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n");
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
+
vc4_hvs_atomic_disable(crtc, old_state);
/*
@@ -410,6 +410,10 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
+ /* Reset the PV fifo. */
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) |
+ PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);
+
/* Enable vblank irq handling before crtc is started otherwise
* drm_crtc_get_vblank() fails in vc4_crtc_update_dlist().
*/
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 12/80] drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The VIDEN bit in the pixelvalve currently being used to enable or disable
the pixelvalve seems to not be enough in some situations, which whill end
up with the pixelvalve stalling.
In such a case, even re-enabling VIDEN doesn't bring it back and we need to
clear the FIFO. This can only be done if the pixelvalve is disabled though.
In order to overcome this, we can configure the pixelvalve during
mode_set_no_fb by calling vc4_crtc_config_pv, but only enable it in
atomic_enable and flush the FIFO there, and in atomic_disable disable the
pixelvalve again.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 10 +++++++---
1 file changed, 7 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index cdeaa0cd981f..fe2e5675aed4 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -332,9 +332,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
PV_CONTROL_TRIGGER_UNDERFLOW |
PV_CONTROL_WAIT_HSTART |
VC4_SET_FIELD(vc4_encoder->clock_select,
- PV_CONTROL_CLK_SELECT) |
- PV_CONTROL_FIFO_CLR |
- PV_CONTROL_EN);
+ PV_CONTROL_CLK_SELECT));
}
static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
@@ -386,6 +384,8 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n");
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
+
vc4_hvs_atomic_disable(crtc, old_state);
/*
@@ -410,6 +410,10 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
+ /* Reset the PV fifo. */
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) |
+ PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);
+
/* Enable vblank irq handling before crtc is started otherwise
* drm_crtc_get_vblank() fails in vc4_crtc_update_dlist().
*/
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 13/80] drm/vc4: kms: Convert to for_each_new_crtc_state
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The vc4 atomic commit loop has an handrolled loop that is basically
identical to for_each_new_crtc_state, let's convert it to that helper.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_kms.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index 210cc2408087..a41d105d4e3c 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -152,14 +152,16 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
struct drm_device *dev = state->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_hvs *hvs = vc4->hvs;
- struct vc4_crtc *vc4_crtc;
+ struct drm_crtc_state *new_crtc_state;
+ struct drm_crtc *crtc;
int i;
- for (i = 0; i < dev->mode_config.num_crtc; i++) {
- if (!state->crtcs[i].ptr || !state->crtcs[i].commit)
+ for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) {
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+
+ if (!new_crtc_state->commit)
continue;
- vc4_crtc = to_vc4_crtc(state->crtcs[i].ptr);
vc4_hvs_mask_underrun(dev, vc4_crtc->channel);
}
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 13/80] drm/vc4: kms: Convert to for_each_new_crtc_state
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The vc4 atomic commit loop has an handrolled loop that is basically
identical to for_each_new_crtc_state, let's convert it to that helper.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_kms.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index 210cc2408087..a41d105d4e3c 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -152,14 +152,16 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
struct drm_device *dev = state->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_hvs *hvs = vc4->hvs;
- struct vc4_crtc *vc4_crtc;
+ struct drm_crtc_state *new_crtc_state;
+ struct drm_crtc *crtc;
int i;
- for (i = 0; i < dev->mode_config.num_crtc; i++) {
- if (!state->crtcs[i].ptr || !state->crtcs[i].commit)
+ for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) {
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+
+ if (!new_crtc_state->commit)
continue;
- vc4_crtc = to_vc4_crtc(state->crtcs[i].ptr);
vc4_hvs_mask_underrun(dev, vc4_crtc->channel);
}
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 13/80] drm/vc4: kms: Convert to for_each_new_crtc_state
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The vc4 atomic commit loop has an handrolled loop that is basically
identical to for_each_new_crtc_state, let's convert it to that helper.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_kms.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index 210cc2408087..a41d105d4e3c 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -152,14 +152,16 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
struct drm_device *dev = state->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_hvs *hvs = vc4->hvs;
- struct vc4_crtc *vc4_crtc;
+ struct drm_crtc_state *new_crtc_state;
+ struct drm_crtc *crtc;
int i;
- for (i = 0; i < dev->mode_config.num_crtc; i++) {
- if (!state->crtcs[i].ptr || !state->crtcs[i].commit)
+ for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) {
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+
+ if (!new_crtc_state->commit)
continue;
- vc4_crtc = to_vc4_crtc(state->crtcs[i].ptr);
vc4_hvs_mask_underrun(dev, vc4_crtc->channel);
}
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 14/80] drm/vc4: crtc: Assign output to channel automatically
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The HVS found in the BCM2711 has 6 outputs and 3 FIFOs, with each output
being connected to a pixelvalve, and some muxing between the FIFOs and
outputs.
Any output cannot feed from any FIFO though, and they all have a bunch of
constraints.
In order to support this, let's store the possible FIFOs each output can be
assigned to in the vc4_crtc_data, and use that information at atomic_check
time to iterate over all the CRTCs enabled and assign them FIFOs.
The channel assigned is then set in the vc4_crtc_state so that the rest of
the driver can use it.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 12 +-
drivers/gpu/drm/vc4/vc4_drv.h | 7 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 28 ++----
drivers/gpu/drm/vc4/vc4_kms.c | 168 +++++++++++++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_regs.h | 10 ++-
drivers/gpu/drm/vc4/vc4_txp.c | 1 +-
6 files changed, 200 insertions(+), 26 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index fe2e5675aed4..b7e47ce1476c 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -88,6 +88,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state);
unsigned int cob_size;
u32 val;
int fifo_lines;
@@ -104,7 +105,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
* Read vertical scanline which is currently composed for our
* pixelvalve by the HVS, and also the scaler status.
*/
- val = HVS_READ(SCALER_DISPSTATX(vc4_crtc->channel));
+ val = HVS_READ(SCALER_DISPSTATX(vc4_crtc_state->assigned_channel));
/* Get optional system timestamp after query. */
if (etime)
@@ -124,7 +125,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
*hpos += mode->crtc_htotal / 2;
}
- cob_size = vc4_crtc_get_cob_allocation(vc4, vc4_crtc->channel);
+ cob_size = vc4_crtc_get_cob_allocation(vc4, vc4_crtc_state->assigned_channel);
/* This is the offset we need for translating hvs -> pv scanout pos. */
fifo_lines = cob_size / mode->crtc_hdisplay;
@@ -520,7 +521,7 @@ static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc)
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
- u32 chan = vc4_crtc->channel;
+ u32 chan = vc4_state->assigned_channel;
unsigned long flags;
spin_lock_irqsave(&dev->event_lock, flags);
@@ -719,6 +720,7 @@ struct drm_crtc_state *vc4_crtc_duplicate_state(struct drm_crtc *crtc)
old_vc4_state = to_vc4_crtc_state(crtc->state);
vc4_state->feed_txp = old_vc4_state->feed_txp;
vc4_state->margins = old_vc4_state->margins;
+ vc4_state->assigned_channel = old_vc4_state->assigned_channel;
__drm_atomic_helper_crtc_duplicate_state(crtc, &vc4_state->base);
return &vc4_state->base;
@@ -779,6 +781,7 @@ static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
static const struct vc4_pv_data bcm2835_pv0_data = {
.base = {
+ .hvs_available_channels = BIT(0),
.hvs_output = 0,
},
.debugfs_name = "crtc0_regs",
@@ -791,6 +794,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
static const struct vc4_pv_data bcm2835_pv1_data = {
.base = {
+ .hvs_available_channels = BIT(2),
.hvs_output = 2,
},
.debugfs_name = "crtc1_regs",
@@ -803,6 +807,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
static const struct vc4_pv_data bcm2835_pv2_data = {
.base = {
+ .hvs_available_channels = BIT(1),
.hvs_output = 1,
},
.debugfs_name = "crtc2_regs",
@@ -866,7 +871,6 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
crtc_funcs, NULL);
drm_crtc_helper_add(crtc, crtc_helper_funcs);
- vc4_crtc->channel = vc4_crtc->data->hvs_output;
drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index d1cf4c038180..9e81ad8331f1 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -447,6 +447,9 @@ to_vc4_encoder(struct drm_encoder *encoder)
}
struct vc4_crtc_data {
+ /* Bitmask of channels (FIFOs) of the HVS that the output can source from */
+ unsigned int hvs_available_channels;
+
/* Which output of the HVS this pixelvalve sources from. */
int hvs_output;
};
@@ -471,9 +474,6 @@ struct vc4_crtc {
/* Timestamp at start of vblank irq - unaffected by lock delays. */
ktime_t t_vblank;
- /* Which HVS channel we're using for our CRTC. */
- int channel;
-
u8 lut_r[256];
u8 lut_g[256];
u8 lut_b[256];
@@ -509,6 +509,7 @@ struct vc4_crtc_state {
struct drm_mm_node mm;
bool feed_txp;
bool txp_armed;
+ unsigned int assigned_channel;
struct {
unsigned int left;
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 365425d67f3f..31a9bc5ef84e 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -161,6 +161,7 @@ static void vc4_hvs_lut_load(struct drm_crtc *crtc)
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
u32 i;
/* The LUT memory is laid out with each HVS channel in order,
@@ -169,7 +170,7 @@ static void vc4_hvs_lut_load(struct drm_crtc *crtc)
*/
HVS_WRITE(SCALER_GAMADDR,
SCALER_GAMADDR_AUTOINC |
- (vc4_crtc->channel * 3 * crtc->gamma_size));
+ (vc4_state->assigned_channel * 3 * crtc->gamma_size));
for (i = 0; i < crtc->gamma_size; i++)
HVS_WRITE(SCALER_GAMDATA, vc4_crtc->lut_r[i]);
@@ -249,12 +250,12 @@ static void vc4_hvs_update_dlist(struct drm_crtc *crtc)
crtc->state->event = NULL;
}
- HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
+ HVS_WRITE(SCALER_DISPLISTX(vc4_state->assigned_channel),
vc4_state->mm.start);
spin_unlock_irqrestore(&dev->event_lock, flags);
} else {
- HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
+ HVS_WRITE(SCALER_DISPLISTX(vc4_state->assigned_channel),
vc4_state->mm.start);
}
}
@@ -264,7 +265,6 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool oneshot = vc4_state->feed_txp;
@@ -292,7 +292,7 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
SCALER5_DISPCTRLX_HEIGHT) |
(oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
- HVS_WRITE(SCALER_DISPCTRLX(vc4_crtc->channel), dispctrl);
+ HVS_WRITE(SCALER_DISPCTRLX(vc4_state->assigned_channel), dispctrl);
}
void vc4_hvs_atomic_disable(struct drm_crtc *crtc,
@@ -300,8 +300,8 @@ void vc4_hvs_atomic_disable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
- u32 chan = vc4_crtc->channel;
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(old_state);
+ unsigned int chan = vc4_state->assigned_channel;
if (HVS_READ(SCALER_DISPCTRLX(chan)) &
SCALER_DISPCTRLX_ENABLE) {
@@ -332,7 +332,6 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_plane *plane;
struct vc4_plane_state *vc4_plane_state;
@@ -374,8 +373,8 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
/* This sets a black background color fill, as is the case
* with other DRM drivers.
*/
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel),
- HVS_READ(SCALER_DISPBKGNDX(vc4_crtc->channel)) |
+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
+ HVS_READ(SCALER_DISPBKGNDX(vc4_state->assigned_channel)) |
SCALER_DISPBKGND_FILL);
/* Only update DISPLIST if the CRTC was already running and is not
@@ -389,7 +388,7 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
vc4_hvs_update_dlist(crtc);
if (crtc->state->color_mgmt_changed) {
- u32 dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(vc4_crtc->channel));
+ u32 dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(vc4_state->assigned_channel));
if (crtc->state->gamma_lut) {
vc4_hvs_update_gamma_lut(crtc);
@@ -401,7 +400,7 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
*/
dispbkgndx &= ~SCALER_DISPBKGND_GAMMA;
}
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel), dispbkgndx);
+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel), dispbkgndx);
}
if (debug_dump_regs) {
@@ -414,12 +413,11 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
- if (vc4_crtc->data->hvs_output == 2) {
+ if (vc4_state->assigned_channel == 2) {
u32 dispctrl;
u32 dsp3_mux;
@@ -443,7 +441,7 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
HVS_WRITE(SCALER_DISPCTRL, dispctrl | dsp3_mux);
}
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel),
+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
SCALER_DISPBKGND_AUTOHS |
SCALER_DISPBKGND_GAMMA |
(interlace ? SCALER_DISPBKGND_INTERLACE : 0));
diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index a41d105d4e3c..bfc7ddd49ac5 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -146,6 +146,107 @@ vc4_ctm_commit(struct vc4_dev *vc4, struct drm_atomic_state *state)
VC4_SET_FIELD(ctm_state->fifo, SCALER_OLEDOFFS_DISPFIFO));
}
+static void vc4_hvs_pv_muxing_commit(struct vc4_dev *vc4,
+ struct drm_atomic_state *state)
+{
+ struct drm_crtc_state *crtc_state;
+ struct drm_crtc *crtc;
+ unsigned int i;
+
+ for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state);
+ u32 dispctrl;
+ u32 dsp3_mux;
+
+ if (!crtc_state->active)
+ continue;
+
+ if (vc4_state->assigned_channel != 2)
+ continue;
+
+ /*
+ * SCALER_DISPCTRL_DSP3 = X, where X < 2 means 'connect DSP3 to
+ * FIFO X'.
+ * SCALER_DISPCTRL_DSP3 = 3 means 'disable DSP 3'.
+ *
+ * DSP3 is connected to FIFO2 unless the transposer is
+ * enabled. In this case, FIFO 2 is directly accessed by the
+ * TXP IP, and we need to disable the FIFO2 -> pixelvalve1
+ * route.
+ */
+ if (vc4_state->feed_txp)
+ dsp3_mux = VC4_SET_FIELD(3, SCALER_DISPCTRL_DSP3_MUX);
+ else
+ dsp3_mux = VC4_SET_FIELD(2, SCALER_DISPCTRL_DSP3_MUX);
+
+ dispctrl = HVS_READ(SCALER_DISPCTRL) &
+ ~SCALER_DISPCTRL_DSP3_MUX_MASK;
+ HVS_WRITE(SCALER_DISPCTRL, dispctrl | dsp3_mux);
+ }
+}
+
+static void vc5_hvs_pv_muxing_commit(struct vc4_dev *vc4,
+ struct drm_atomic_state *state)
+{
+ struct drm_crtc_state *crtc_state;
+ struct drm_crtc *crtc;
+ unsigned char dsp2_mux = 0;
+ unsigned char dsp3_mux = 3;
+ unsigned char dsp4_mux = 3;
+ unsigned char dsp5_mux = 3;
+ unsigned int i;
+ u32 reg;
+
+ for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state);
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+
+ if (!crtc_state->active)
+ continue;
+
+ switch (vc4_crtc->data->hvs_output) {
+ case 2:
+ dsp2_mux = (vc4_state->assigned_channel == 2) ? 0 : 1;
+ break;
+
+ case 3:
+ dsp3_mux = vc4_state->assigned_channel;
+ break;
+
+ case 4:
+ dsp4_mux = vc4_state->assigned_channel;
+ break;
+
+ case 5:
+ dsp5_mux = vc4_state->assigned_channel;
+ break;
+
+ default:
+ break;
+ }
+ }
+
+ reg = HVS_READ(SCALER_DISPECTRL);
+ HVS_WRITE(SCALER_DISPECTRL,
+ (reg & ~SCALER_DISPECTRL_DSP2_MUX_MASK) |
+ VC4_SET_FIELD(dsp2_mux, SCALER_DISPECTRL_DSP2_MUX));
+
+ reg = HVS_READ(SCALER_DISPCTRL);
+ HVS_WRITE(SCALER_DISPCTRL,
+ (reg & ~SCALER_DISPCTRL_DSP3_MUX_MASK) |
+ VC4_SET_FIELD(dsp3_mux, SCALER_DISPCTRL_DSP3_MUX));
+
+ reg = HVS_READ(SCALER_DISPEOLN);
+ HVS_WRITE(SCALER_DISPEOLN,
+ (reg & ~SCALER_DISPEOLN_DSP4_MUX_MASK) |
+ VC4_SET_FIELD(dsp4_mux, SCALER_DISPEOLN_DSP4_MUX));
+
+ reg = HVS_READ(SCALER_DISPDITHER);
+ HVS_WRITE(SCALER_DISPDITHER,
+ (reg & ~SCALER_DISPDITHER_DSP5_MUX_MASK) |
+ VC4_SET_FIELD(dsp5_mux, SCALER_DISPDITHER_DSP5_MUX));
+}
+
static void
vc4_atomic_complete_commit(struct drm_atomic_state *state)
{
@@ -157,12 +258,13 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
int i;
for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) {
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct vc4_crtc_state *vc4_crtc_state;
if (!new_crtc_state->commit)
continue;
- vc4_hvs_mask_underrun(dev, vc4_crtc->channel);
+ vc4_crtc_state = to_vc4_crtc_state(new_crtc_state);
+ vc4_hvs_mask_underrun(dev, vc4_crtc_state->assigned_channel);
}
if (vc4->hvs->hvs5)
@@ -176,6 +278,11 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
vc4_ctm_commit(vc4, state);
+ if (vc4->hvs->hvs5)
+ vc5_hvs_pv_muxing_commit(vc4, state);
+ else
+ vc4_hvs_pv_muxing_commit(vc4, state);
+
drm_atomic_helper_commit_planes(dev, state, 0);
drm_atomic_helper_commit_modeset_enables(dev, state);
@@ -385,8 +492,11 @@ vc4_ctm_atomic_check(struct drm_device *dev, struct drm_atomic_state *state)
/* CTM is being enabled or the matrix changed. */
if (new_crtc_state->ctm) {
+ struct vc4_crtc_state *vc4_crtc_state =
+ to_vc4_crtc_state(new_crtc_state);
+
/* fifo is 1-based since 0 disables CTM. */
- int fifo = to_vc4_crtc(crtc)->channel + 1;
+ int fifo = vc4_crtc_state->assigned_channel + 1;
/* Check userland isn't trying to turn on CTM for more
* than one CRTC at a time.
@@ -496,10 +606,60 @@ static const struct drm_private_state_funcs vc4_load_tracker_state_funcs = {
.atomic_destroy_state = vc4_load_tracker_destroy_state,
};
+#define NUM_OUTPUTS 6
+#define NUM_CHANNELS 3
+
static int
vc4_atomic_check(struct drm_device *dev, struct drm_atomic_state *state)
{
- int ret;
+ unsigned long unassigned_channels = GENMASK(NUM_CHANNELS - 1, 0);
+ struct drm_crtc_state *crtc_state;
+ struct drm_crtc *crtc;
+ int i, ret;
+
+ for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+ struct vc4_crtc_state *vc4_crtc_state =
+ to_vc4_crtc_state(crtc_state);
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ unsigned int matching_channels;
+
+ if (!crtc_state->active)
+ continue;
+
+ /*
+ * The problem we have to solve here is that we have
+ * up to 7 encoders, connected to up to 6 CRTCs.
+ *
+ * Those CRTCs, depending on the instance, can be
+ * routed to 1, 2 or 3 HVS FIFOs, and we need to set
+ * the change the muxing between FIFOs and outputs in
+ * the HVS accordingly.
+ *
+ * It would be pretty hard to come up with an
+ * algorithm that would generically solve
+ * this. However, the current routing trees we support
+ * allow us to simplify a bit the problem.
+ *
+ * Indeed, with the current supported layouts, if we
+ * try to assign in the ascending crtc index order the
+ * FIFOs, we can't fall into the situation where an
+ * earlier CRTC that had multiple routes is assigned
+ * one that was the only option for a later CRTC.
+ *
+ * If the layout changes and doesn't give us that in
+ * the future, we will need to have something smarter,
+ * but it works so far.
+ */
+ matching_channels = unassigned_channels & vc4_crtc->data->hvs_available_channels;
+ if (matching_channels) {
+ unsigned int channel = ffs(matching_channels) - 1;
+
+ vc4_crtc_state->assigned_channel = channel;
+ unassigned_channels &= ~BIT(channel);
+ } else {
+ return -EINVAL;
+ }
+ }
ret = vc4_ctm_atomic_check(dev, state);
if (ret < 0)
diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h
index 91b785725555..7fbac68b6fe1 100644
--- a/drivers/gpu/drm/vc4/vc4_regs.h
+++ b/drivers/gpu/drm/vc4/vc4_regs.h
@@ -286,9 +286,19 @@
#define SCALER_DISPID 0x00000008
#define SCALER_DISPECTRL 0x0000000c
+# define SCALER_DISPECTRL_DSP2_MUX_SHIFT 31
+# define SCALER_DISPECTRL_DSP2_MUX_MASK VC4_MASK(31, 31)
+
#define SCALER_DISPPROF 0x00000010
+
#define SCALER_DISPDITHER 0x00000014
+# define SCALER_DISPDITHER_DSP5_MUX_SHIFT 30
+# define SCALER_DISPDITHER_DSP5_MUX_MASK VC4_MASK(31, 30)
+
#define SCALER_DISPEOLN 0x00000018
+# define SCALER_DISPEOLN_DSP4_MUX_SHIFT 30
+# define SCALER_DISPEOLN_DSP4_MUX_MASK VC4_MASK(31, 30)
+
#define SCALER_DISPLIST0 0x00000020
#define SCALER_DISPLIST1 0x00000024
#define SCALER_DISPLIST2 0x00000028
diff --git a/drivers/gpu/drm/vc4/vc4_txp.c b/drivers/gpu/drm/vc4/vc4_txp.c
index f39d9900d027..a2380d856000 100644
--- a/drivers/gpu/drm/vc4/vc4_txp.c
+++ b/drivers/gpu/drm/vc4/vc4_txp.c
@@ -452,6 +452,7 @@ static irqreturn_t vc4_txp_interrupt(int irq, void *data)
}
static const struct vc4_crtc_data vc4_txp_crtc_data = {
+ .hvs_available_channels = BIT(2),
.hvs_output = 2,
};
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 14/80] drm/vc4: crtc: Assign output to channel automatically
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The HVS found in the BCM2711 has 6 outputs and 3 FIFOs, with each output
being connected to a pixelvalve, and some muxing between the FIFOs and
outputs.
Any output cannot feed from any FIFO though, and they all have a bunch of
constraints.
In order to support this, let's store the possible FIFOs each output can be
assigned to in the vc4_crtc_data, and use that information at atomic_check
time to iterate over all the CRTCs enabled and assign them FIFOs.
The channel assigned is then set in the vc4_crtc_state so that the rest of
the driver can use it.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 12 +-
drivers/gpu/drm/vc4/vc4_drv.h | 7 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 28 ++----
drivers/gpu/drm/vc4/vc4_kms.c | 168 +++++++++++++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_regs.h | 10 ++-
drivers/gpu/drm/vc4/vc4_txp.c | 1 +-
6 files changed, 200 insertions(+), 26 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index fe2e5675aed4..b7e47ce1476c 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -88,6 +88,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state);
unsigned int cob_size;
u32 val;
int fifo_lines;
@@ -104,7 +105,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
* Read vertical scanline which is currently composed for our
* pixelvalve by the HVS, and also the scaler status.
*/
- val = HVS_READ(SCALER_DISPSTATX(vc4_crtc->channel));
+ val = HVS_READ(SCALER_DISPSTATX(vc4_crtc_state->assigned_channel));
/* Get optional system timestamp after query. */
if (etime)
@@ -124,7 +125,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
*hpos += mode->crtc_htotal / 2;
}
- cob_size = vc4_crtc_get_cob_allocation(vc4, vc4_crtc->channel);
+ cob_size = vc4_crtc_get_cob_allocation(vc4, vc4_crtc_state->assigned_channel);
/* This is the offset we need for translating hvs -> pv scanout pos. */
fifo_lines = cob_size / mode->crtc_hdisplay;
@@ -520,7 +521,7 @@ static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc)
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
- u32 chan = vc4_crtc->channel;
+ u32 chan = vc4_state->assigned_channel;
unsigned long flags;
spin_lock_irqsave(&dev->event_lock, flags);
@@ -719,6 +720,7 @@ struct drm_crtc_state *vc4_crtc_duplicate_state(struct drm_crtc *crtc)
old_vc4_state = to_vc4_crtc_state(crtc->state);
vc4_state->feed_txp = old_vc4_state->feed_txp;
vc4_state->margins = old_vc4_state->margins;
+ vc4_state->assigned_channel = old_vc4_state->assigned_channel;
__drm_atomic_helper_crtc_duplicate_state(crtc, &vc4_state->base);
return &vc4_state->base;
@@ -779,6 +781,7 @@ static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
static const struct vc4_pv_data bcm2835_pv0_data = {
.base = {
+ .hvs_available_channels = BIT(0),
.hvs_output = 0,
},
.debugfs_name = "crtc0_regs",
@@ -791,6 +794,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
static const struct vc4_pv_data bcm2835_pv1_data = {
.base = {
+ .hvs_available_channels = BIT(2),
.hvs_output = 2,
},
.debugfs_name = "crtc1_regs",
@@ -803,6 +807,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
static const struct vc4_pv_data bcm2835_pv2_data = {
.base = {
+ .hvs_available_channels = BIT(1),
.hvs_output = 1,
},
.debugfs_name = "crtc2_regs",
@@ -866,7 +871,6 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
crtc_funcs, NULL);
drm_crtc_helper_add(crtc, crtc_helper_funcs);
- vc4_crtc->channel = vc4_crtc->data->hvs_output;
drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index d1cf4c038180..9e81ad8331f1 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -447,6 +447,9 @@ to_vc4_encoder(struct drm_encoder *encoder)
}
struct vc4_crtc_data {
+ /* Bitmask of channels (FIFOs) of the HVS that the output can source from */
+ unsigned int hvs_available_channels;
+
/* Which output of the HVS this pixelvalve sources from. */
int hvs_output;
};
@@ -471,9 +474,6 @@ struct vc4_crtc {
/* Timestamp at start of vblank irq - unaffected by lock delays. */
ktime_t t_vblank;
- /* Which HVS channel we're using for our CRTC. */
- int channel;
-
u8 lut_r[256];
u8 lut_g[256];
u8 lut_b[256];
@@ -509,6 +509,7 @@ struct vc4_crtc_state {
struct drm_mm_node mm;
bool feed_txp;
bool txp_armed;
+ unsigned int assigned_channel;
struct {
unsigned int left;
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 365425d67f3f..31a9bc5ef84e 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -161,6 +161,7 @@ static void vc4_hvs_lut_load(struct drm_crtc *crtc)
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
u32 i;
/* The LUT memory is laid out with each HVS channel in order,
@@ -169,7 +170,7 @@ static void vc4_hvs_lut_load(struct drm_crtc *crtc)
*/
HVS_WRITE(SCALER_GAMADDR,
SCALER_GAMADDR_AUTOINC |
- (vc4_crtc->channel * 3 * crtc->gamma_size));
+ (vc4_state->assigned_channel * 3 * crtc->gamma_size));
for (i = 0; i < crtc->gamma_size; i++)
HVS_WRITE(SCALER_GAMDATA, vc4_crtc->lut_r[i]);
@@ -249,12 +250,12 @@ static void vc4_hvs_update_dlist(struct drm_crtc *crtc)
crtc->state->event = NULL;
}
- HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
+ HVS_WRITE(SCALER_DISPLISTX(vc4_state->assigned_channel),
vc4_state->mm.start);
spin_unlock_irqrestore(&dev->event_lock, flags);
} else {
- HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
+ HVS_WRITE(SCALER_DISPLISTX(vc4_state->assigned_channel),
vc4_state->mm.start);
}
}
@@ -264,7 +265,6 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool oneshot = vc4_state->feed_txp;
@@ -292,7 +292,7 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
SCALER5_DISPCTRLX_HEIGHT) |
(oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
- HVS_WRITE(SCALER_DISPCTRLX(vc4_crtc->channel), dispctrl);
+ HVS_WRITE(SCALER_DISPCTRLX(vc4_state->assigned_channel), dispctrl);
}
void vc4_hvs_atomic_disable(struct drm_crtc *crtc,
@@ -300,8 +300,8 @@ void vc4_hvs_atomic_disable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
- u32 chan = vc4_crtc->channel;
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(old_state);
+ unsigned int chan = vc4_state->assigned_channel;
if (HVS_READ(SCALER_DISPCTRLX(chan)) &
SCALER_DISPCTRLX_ENABLE) {
@@ -332,7 +332,6 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_plane *plane;
struct vc4_plane_state *vc4_plane_state;
@@ -374,8 +373,8 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
/* This sets a black background color fill, as is the case
* with other DRM drivers.
*/
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel),
- HVS_READ(SCALER_DISPBKGNDX(vc4_crtc->channel)) |
+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
+ HVS_READ(SCALER_DISPBKGNDX(vc4_state->assigned_channel)) |
SCALER_DISPBKGND_FILL);
/* Only update DISPLIST if the CRTC was already running and is not
@@ -389,7 +388,7 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
vc4_hvs_update_dlist(crtc);
if (crtc->state->color_mgmt_changed) {
- u32 dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(vc4_crtc->channel));
+ u32 dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(vc4_state->assigned_channel));
if (crtc->state->gamma_lut) {
vc4_hvs_update_gamma_lut(crtc);
@@ -401,7 +400,7 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
*/
dispbkgndx &= ~SCALER_DISPBKGND_GAMMA;
}
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel), dispbkgndx);
+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel), dispbkgndx);
}
if (debug_dump_regs) {
@@ -414,12 +413,11 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
- if (vc4_crtc->data->hvs_output == 2) {
+ if (vc4_state->assigned_channel == 2) {
u32 dispctrl;
u32 dsp3_mux;
@@ -443,7 +441,7 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
HVS_WRITE(SCALER_DISPCTRL, dispctrl | dsp3_mux);
}
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel),
+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
SCALER_DISPBKGND_AUTOHS |
SCALER_DISPBKGND_GAMMA |
(interlace ? SCALER_DISPBKGND_INTERLACE : 0));
diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index a41d105d4e3c..bfc7ddd49ac5 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -146,6 +146,107 @@ vc4_ctm_commit(struct vc4_dev *vc4, struct drm_atomic_state *state)
VC4_SET_FIELD(ctm_state->fifo, SCALER_OLEDOFFS_DISPFIFO));
}
+static void vc4_hvs_pv_muxing_commit(struct vc4_dev *vc4,
+ struct drm_atomic_state *state)
+{
+ struct drm_crtc_state *crtc_state;
+ struct drm_crtc *crtc;
+ unsigned int i;
+
+ for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state);
+ u32 dispctrl;
+ u32 dsp3_mux;
+
+ if (!crtc_state->active)
+ continue;
+
+ if (vc4_state->assigned_channel != 2)
+ continue;
+
+ /*
+ * SCALER_DISPCTRL_DSP3 = X, where X < 2 means 'connect DSP3 to
+ * FIFO X'.
+ * SCALER_DISPCTRL_DSP3 = 3 means 'disable DSP 3'.
+ *
+ * DSP3 is connected to FIFO2 unless the transposer is
+ * enabled. In this case, FIFO 2 is directly accessed by the
+ * TXP IP, and we need to disable the FIFO2 -> pixelvalve1
+ * route.
+ */
+ if (vc4_state->feed_txp)
+ dsp3_mux = VC4_SET_FIELD(3, SCALER_DISPCTRL_DSP3_MUX);
+ else
+ dsp3_mux = VC4_SET_FIELD(2, SCALER_DISPCTRL_DSP3_MUX);
+
+ dispctrl = HVS_READ(SCALER_DISPCTRL) &
+ ~SCALER_DISPCTRL_DSP3_MUX_MASK;
+ HVS_WRITE(SCALER_DISPCTRL, dispctrl | dsp3_mux);
+ }
+}
+
+static void vc5_hvs_pv_muxing_commit(struct vc4_dev *vc4,
+ struct drm_atomic_state *state)
+{
+ struct drm_crtc_state *crtc_state;
+ struct drm_crtc *crtc;
+ unsigned char dsp2_mux = 0;
+ unsigned char dsp3_mux = 3;
+ unsigned char dsp4_mux = 3;
+ unsigned char dsp5_mux = 3;
+ unsigned int i;
+ u32 reg;
+
+ for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state);
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+
+ if (!crtc_state->active)
+ continue;
+
+ switch (vc4_crtc->data->hvs_output) {
+ case 2:
+ dsp2_mux = (vc4_state->assigned_channel == 2) ? 0 : 1;
+ break;
+
+ case 3:
+ dsp3_mux = vc4_state->assigned_channel;
+ break;
+
+ case 4:
+ dsp4_mux = vc4_state->assigned_channel;
+ break;
+
+ case 5:
+ dsp5_mux = vc4_state->assigned_channel;
+ break;
+
+ default:
+ break;
+ }
+ }
+
+ reg = HVS_READ(SCALER_DISPECTRL);
+ HVS_WRITE(SCALER_DISPECTRL,
+ (reg & ~SCALER_DISPECTRL_DSP2_MUX_MASK) |
+ VC4_SET_FIELD(dsp2_mux, SCALER_DISPECTRL_DSP2_MUX));
+
+ reg = HVS_READ(SCALER_DISPCTRL);
+ HVS_WRITE(SCALER_DISPCTRL,
+ (reg & ~SCALER_DISPCTRL_DSP3_MUX_MASK) |
+ VC4_SET_FIELD(dsp3_mux, SCALER_DISPCTRL_DSP3_MUX));
+
+ reg = HVS_READ(SCALER_DISPEOLN);
+ HVS_WRITE(SCALER_DISPEOLN,
+ (reg & ~SCALER_DISPEOLN_DSP4_MUX_MASK) |
+ VC4_SET_FIELD(dsp4_mux, SCALER_DISPEOLN_DSP4_MUX));
+
+ reg = HVS_READ(SCALER_DISPDITHER);
+ HVS_WRITE(SCALER_DISPDITHER,
+ (reg & ~SCALER_DISPDITHER_DSP5_MUX_MASK) |
+ VC4_SET_FIELD(dsp5_mux, SCALER_DISPDITHER_DSP5_MUX));
+}
+
static void
vc4_atomic_complete_commit(struct drm_atomic_state *state)
{
@@ -157,12 +258,13 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
int i;
for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) {
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct vc4_crtc_state *vc4_crtc_state;
if (!new_crtc_state->commit)
continue;
- vc4_hvs_mask_underrun(dev, vc4_crtc->channel);
+ vc4_crtc_state = to_vc4_crtc_state(new_crtc_state);
+ vc4_hvs_mask_underrun(dev, vc4_crtc_state->assigned_channel);
}
if (vc4->hvs->hvs5)
@@ -176,6 +278,11 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
vc4_ctm_commit(vc4, state);
+ if (vc4->hvs->hvs5)
+ vc5_hvs_pv_muxing_commit(vc4, state);
+ else
+ vc4_hvs_pv_muxing_commit(vc4, state);
+
drm_atomic_helper_commit_planes(dev, state, 0);
drm_atomic_helper_commit_modeset_enables(dev, state);
@@ -385,8 +492,11 @@ vc4_ctm_atomic_check(struct drm_device *dev, struct drm_atomic_state *state)
/* CTM is being enabled or the matrix changed. */
if (new_crtc_state->ctm) {
+ struct vc4_crtc_state *vc4_crtc_state =
+ to_vc4_crtc_state(new_crtc_state);
+
/* fifo is 1-based since 0 disables CTM. */
- int fifo = to_vc4_crtc(crtc)->channel + 1;
+ int fifo = vc4_crtc_state->assigned_channel + 1;
/* Check userland isn't trying to turn on CTM for more
* than one CRTC at a time.
@@ -496,10 +606,60 @@ static const struct drm_private_state_funcs vc4_load_tracker_state_funcs = {
.atomic_destroy_state = vc4_load_tracker_destroy_state,
};
+#define NUM_OUTPUTS 6
+#define NUM_CHANNELS 3
+
static int
vc4_atomic_check(struct drm_device *dev, struct drm_atomic_state *state)
{
- int ret;
+ unsigned long unassigned_channels = GENMASK(NUM_CHANNELS - 1, 0);
+ struct drm_crtc_state *crtc_state;
+ struct drm_crtc *crtc;
+ int i, ret;
+
+ for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+ struct vc4_crtc_state *vc4_crtc_state =
+ to_vc4_crtc_state(crtc_state);
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ unsigned int matching_channels;
+
+ if (!crtc_state->active)
+ continue;
+
+ /*
+ * The problem we have to solve here is that we have
+ * up to 7 encoders, connected to up to 6 CRTCs.
+ *
+ * Those CRTCs, depending on the instance, can be
+ * routed to 1, 2 or 3 HVS FIFOs, and we need to set
+ * the change the muxing between FIFOs and outputs in
+ * the HVS accordingly.
+ *
+ * It would be pretty hard to come up with an
+ * algorithm that would generically solve
+ * this. However, the current routing trees we support
+ * allow us to simplify a bit the problem.
+ *
+ * Indeed, with the current supported layouts, if we
+ * try to assign in the ascending crtc index order the
+ * FIFOs, we can't fall into the situation where an
+ * earlier CRTC that had multiple routes is assigned
+ * one that was the only option for a later CRTC.
+ *
+ * If the layout changes and doesn't give us that in
+ * the future, we will need to have something smarter,
+ * but it works so far.
+ */
+ matching_channels = unassigned_channels & vc4_crtc->data->hvs_available_channels;
+ if (matching_channels) {
+ unsigned int channel = ffs(matching_channels) - 1;
+
+ vc4_crtc_state->assigned_channel = channel;
+ unassigned_channels &= ~BIT(channel);
+ } else {
+ return -EINVAL;
+ }
+ }
ret = vc4_ctm_atomic_check(dev, state);
if (ret < 0)
diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h
index 91b785725555..7fbac68b6fe1 100644
--- a/drivers/gpu/drm/vc4/vc4_regs.h
+++ b/drivers/gpu/drm/vc4/vc4_regs.h
@@ -286,9 +286,19 @@
#define SCALER_DISPID 0x00000008
#define SCALER_DISPECTRL 0x0000000c
+# define SCALER_DISPECTRL_DSP2_MUX_SHIFT 31
+# define SCALER_DISPECTRL_DSP2_MUX_MASK VC4_MASK(31, 31)
+
#define SCALER_DISPPROF 0x00000010
+
#define SCALER_DISPDITHER 0x00000014
+# define SCALER_DISPDITHER_DSP5_MUX_SHIFT 30
+# define SCALER_DISPDITHER_DSP5_MUX_MASK VC4_MASK(31, 30)
+
#define SCALER_DISPEOLN 0x00000018
+# define SCALER_DISPEOLN_DSP4_MUX_SHIFT 30
+# define SCALER_DISPEOLN_DSP4_MUX_MASK VC4_MASK(31, 30)
+
#define SCALER_DISPLIST0 0x00000020
#define SCALER_DISPLIST1 0x00000024
#define SCALER_DISPLIST2 0x00000028
diff --git a/drivers/gpu/drm/vc4/vc4_txp.c b/drivers/gpu/drm/vc4/vc4_txp.c
index f39d9900d027..a2380d856000 100644
--- a/drivers/gpu/drm/vc4/vc4_txp.c
+++ b/drivers/gpu/drm/vc4/vc4_txp.c
@@ -452,6 +452,7 @@ static irqreturn_t vc4_txp_interrupt(int irq, void *data)
}
static const struct vc4_crtc_data vc4_txp_crtc_data = {
+ .hvs_available_channels = BIT(2),
.hvs_output = 2,
};
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 14/80] drm/vc4: crtc: Assign output to channel automatically
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The HVS found in the BCM2711 has 6 outputs and 3 FIFOs, with each output
being connected to a pixelvalve, and some muxing between the FIFOs and
outputs.
Any output cannot feed from any FIFO though, and they all have a bunch of
constraints.
In order to support this, let's store the possible FIFOs each output can be
assigned to in the vc4_crtc_data, and use that information at atomic_check
time to iterate over all the CRTCs enabled and assign them FIFOs.
The channel assigned is then set in the vc4_crtc_state so that the rest of
the driver can use it.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 12 +-
drivers/gpu/drm/vc4/vc4_drv.h | 7 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 28 ++----
drivers/gpu/drm/vc4/vc4_kms.c | 168 +++++++++++++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_regs.h | 10 ++-
drivers/gpu/drm/vc4/vc4_txp.c | 1 +-
6 files changed, 200 insertions(+), 26 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index fe2e5675aed4..b7e47ce1476c 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -88,6 +88,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state);
unsigned int cob_size;
u32 val;
int fifo_lines;
@@ -104,7 +105,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
* Read vertical scanline which is currently composed for our
* pixelvalve by the HVS, and also the scaler status.
*/
- val = HVS_READ(SCALER_DISPSTATX(vc4_crtc->channel));
+ val = HVS_READ(SCALER_DISPSTATX(vc4_crtc_state->assigned_channel));
/* Get optional system timestamp after query. */
if (etime)
@@ -124,7 +125,7 @@ static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc,
*hpos += mode->crtc_htotal / 2;
}
- cob_size = vc4_crtc_get_cob_allocation(vc4, vc4_crtc->channel);
+ cob_size = vc4_crtc_get_cob_allocation(vc4, vc4_crtc_state->assigned_channel);
/* This is the offset we need for translating hvs -> pv scanout pos. */
fifo_lines = cob_size / mode->crtc_hdisplay;
@@ -520,7 +521,7 @@ static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc)
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
- u32 chan = vc4_crtc->channel;
+ u32 chan = vc4_state->assigned_channel;
unsigned long flags;
spin_lock_irqsave(&dev->event_lock, flags);
@@ -719,6 +720,7 @@ struct drm_crtc_state *vc4_crtc_duplicate_state(struct drm_crtc *crtc)
old_vc4_state = to_vc4_crtc_state(crtc->state);
vc4_state->feed_txp = old_vc4_state->feed_txp;
vc4_state->margins = old_vc4_state->margins;
+ vc4_state->assigned_channel = old_vc4_state->assigned_channel;
__drm_atomic_helper_crtc_duplicate_state(crtc, &vc4_state->base);
return &vc4_state->base;
@@ -779,6 +781,7 @@ static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
static const struct vc4_pv_data bcm2835_pv0_data = {
.base = {
+ .hvs_available_channels = BIT(0),
.hvs_output = 0,
},
.debugfs_name = "crtc0_regs",
@@ -791,6 +794,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
static const struct vc4_pv_data bcm2835_pv1_data = {
.base = {
+ .hvs_available_channels = BIT(2),
.hvs_output = 2,
},
.debugfs_name = "crtc1_regs",
@@ -803,6 +807,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
static const struct vc4_pv_data bcm2835_pv2_data = {
.base = {
+ .hvs_available_channels = BIT(1),
.hvs_output = 1,
},
.debugfs_name = "crtc2_regs",
@@ -866,7 +871,6 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
crtc_funcs, NULL);
drm_crtc_helper_add(crtc, crtc_helper_funcs);
- vc4_crtc->channel = vc4_crtc->data->hvs_output;
drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index d1cf4c038180..9e81ad8331f1 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -447,6 +447,9 @@ to_vc4_encoder(struct drm_encoder *encoder)
}
struct vc4_crtc_data {
+ /* Bitmask of channels (FIFOs) of the HVS that the output can source from */
+ unsigned int hvs_available_channels;
+
/* Which output of the HVS this pixelvalve sources from. */
int hvs_output;
};
@@ -471,9 +474,6 @@ struct vc4_crtc {
/* Timestamp at start of vblank irq - unaffected by lock delays. */
ktime_t t_vblank;
- /* Which HVS channel we're using for our CRTC. */
- int channel;
-
u8 lut_r[256];
u8 lut_g[256];
u8 lut_b[256];
@@ -509,6 +509,7 @@ struct vc4_crtc_state {
struct drm_mm_node mm;
bool feed_txp;
bool txp_armed;
+ unsigned int assigned_channel;
struct {
unsigned int left;
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 365425d67f3f..31a9bc5ef84e 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -161,6 +161,7 @@ static void vc4_hvs_lut_load(struct drm_crtc *crtc)
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
u32 i;
/* The LUT memory is laid out with each HVS channel in order,
@@ -169,7 +170,7 @@ static void vc4_hvs_lut_load(struct drm_crtc *crtc)
*/
HVS_WRITE(SCALER_GAMADDR,
SCALER_GAMADDR_AUTOINC |
- (vc4_crtc->channel * 3 * crtc->gamma_size));
+ (vc4_state->assigned_channel * 3 * crtc->gamma_size));
for (i = 0; i < crtc->gamma_size; i++)
HVS_WRITE(SCALER_GAMDATA, vc4_crtc->lut_r[i]);
@@ -249,12 +250,12 @@ static void vc4_hvs_update_dlist(struct drm_crtc *crtc)
crtc->state->event = NULL;
}
- HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
+ HVS_WRITE(SCALER_DISPLISTX(vc4_state->assigned_channel),
vc4_state->mm.start);
spin_unlock_irqrestore(&dev->event_lock, flags);
} else {
- HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
+ HVS_WRITE(SCALER_DISPLISTX(vc4_state->assigned_channel),
vc4_state->mm.start);
}
}
@@ -264,7 +265,6 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool oneshot = vc4_state->feed_txp;
@@ -292,7 +292,7 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
SCALER5_DISPCTRLX_HEIGHT) |
(oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
- HVS_WRITE(SCALER_DISPCTRLX(vc4_crtc->channel), dispctrl);
+ HVS_WRITE(SCALER_DISPCTRLX(vc4_state->assigned_channel), dispctrl);
}
void vc4_hvs_atomic_disable(struct drm_crtc *crtc,
@@ -300,8 +300,8 @@ void vc4_hvs_atomic_disable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
- u32 chan = vc4_crtc->channel;
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(old_state);
+ unsigned int chan = vc4_state->assigned_channel;
if (HVS_READ(SCALER_DISPCTRLX(chan)) &
SCALER_DISPCTRLX_ENABLE) {
@@ -332,7 +332,6 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_plane *plane;
struct vc4_plane_state *vc4_plane_state;
@@ -374,8 +373,8 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
/* This sets a black background color fill, as is the case
* with other DRM drivers.
*/
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel),
- HVS_READ(SCALER_DISPBKGNDX(vc4_crtc->channel)) |
+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
+ HVS_READ(SCALER_DISPBKGNDX(vc4_state->assigned_channel)) |
SCALER_DISPBKGND_FILL);
/* Only update DISPLIST if the CRTC was already running and is not
@@ -389,7 +388,7 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
vc4_hvs_update_dlist(crtc);
if (crtc->state->color_mgmt_changed) {
- u32 dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(vc4_crtc->channel));
+ u32 dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(vc4_state->assigned_channel));
if (crtc->state->gamma_lut) {
vc4_hvs_update_gamma_lut(crtc);
@@ -401,7 +400,7 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
*/
dispbkgndx &= ~SCALER_DISPBKGND_GAMMA;
}
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel), dispbkgndx);
+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel), dispbkgndx);
}
if (debug_dump_regs) {
@@ -414,12 +413,11 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
{
struct drm_device *dev = crtc->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
- if (vc4_crtc->data->hvs_output == 2) {
+ if (vc4_state->assigned_channel == 2) {
u32 dispctrl;
u32 dsp3_mux;
@@ -443,7 +441,7 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
HVS_WRITE(SCALER_DISPCTRL, dispctrl | dsp3_mux);
}
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel),
+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
SCALER_DISPBKGND_AUTOHS |
SCALER_DISPBKGND_GAMMA |
(interlace ? SCALER_DISPBKGND_INTERLACE : 0));
diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index a41d105d4e3c..bfc7ddd49ac5 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -146,6 +146,107 @@ vc4_ctm_commit(struct vc4_dev *vc4, struct drm_atomic_state *state)
VC4_SET_FIELD(ctm_state->fifo, SCALER_OLEDOFFS_DISPFIFO));
}
+static void vc4_hvs_pv_muxing_commit(struct vc4_dev *vc4,
+ struct drm_atomic_state *state)
+{
+ struct drm_crtc_state *crtc_state;
+ struct drm_crtc *crtc;
+ unsigned int i;
+
+ for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state);
+ u32 dispctrl;
+ u32 dsp3_mux;
+
+ if (!crtc_state->active)
+ continue;
+
+ if (vc4_state->assigned_channel != 2)
+ continue;
+
+ /*
+ * SCALER_DISPCTRL_DSP3 = X, where X < 2 means 'connect DSP3 to
+ * FIFO X'.
+ * SCALER_DISPCTRL_DSP3 = 3 means 'disable DSP 3'.
+ *
+ * DSP3 is connected to FIFO2 unless the transposer is
+ * enabled. In this case, FIFO 2 is directly accessed by the
+ * TXP IP, and we need to disable the FIFO2 -> pixelvalve1
+ * route.
+ */
+ if (vc4_state->feed_txp)
+ dsp3_mux = VC4_SET_FIELD(3, SCALER_DISPCTRL_DSP3_MUX);
+ else
+ dsp3_mux = VC4_SET_FIELD(2, SCALER_DISPCTRL_DSP3_MUX);
+
+ dispctrl = HVS_READ(SCALER_DISPCTRL) &
+ ~SCALER_DISPCTRL_DSP3_MUX_MASK;
+ HVS_WRITE(SCALER_DISPCTRL, dispctrl | dsp3_mux);
+ }
+}
+
+static void vc5_hvs_pv_muxing_commit(struct vc4_dev *vc4,
+ struct drm_atomic_state *state)
+{
+ struct drm_crtc_state *crtc_state;
+ struct drm_crtc *crtc;
+ unsigned char dsp2_mux = 0;
+ unsigned char dsp3_mux = 3;
+ unsigned char dsp4_mux = 3;
+ unsigned char dsp5_mux = 3;
+ unsigned int i;
+ u32 reg;
+
+ for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state);
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+
+ if (!crtc_state->active)
+ continue;
+
+ switch (vc4_crtc->data->hvs_output) {
+ case 2:
+ dsp2_mux = (vc4_state->assigned_channel == 2) ? 0 : 1;
+ break;
+
+ case 3:
+ dsp3_mux = vc4_state->assigned_channel;
+ break;
+
+ case 4:
+ dsp4_mux = vc4_state->assigned_channel;
+ break;
+
+ case 5:
+ dsp5_mux = vc4_state->assigned_channel;
+ break;
+
+ default:
+ break;
+ }
+ }
+
+ reg = HVS_READ(SCALER_DISPECTRL);
+ HVS_WRITE(SCALER_DISPECTRL,
+ (reg & ~SCALER_DISPECTRL_DSP2_MUX_MASK) |
+ VC4_SET_FIELD(dsp2_mux, SCALER_DISPECTRL_DSP2_MUX));
+
+ reg = HVS_READ(SCALER_DISPCTRL);
+ HVS_WRITE(SCALER_DISPCTRL,
+ (reg & ~SCALER_DISPCTRL_DSP3_MUX_MASK) |
+ VC4_SET_FIELD(dsp3_mux, SCALER_DISPCTRL_DSP3_MUX));
+
+ reg = HVS_READ(SCALER_DISPEOLN);
+ HVS_WRITE(SCALER_DISPEOLN,
+ (reg & ~SCALER_DISPEOLN_DSP4_MUX_MASK) |
+ VC4_SET_FIELD(dsp4_mux, SCALER_DISPEOLN_DSP4_MUX));
+
+ reg = HVS_READ(SCALER_DISPDITHER);
+ HVS_WRITE(SCALER_DISPDITHER,
+ (reg & ~SCALER_DISPDITHER_DSP5_MUX_MASK) |
+ VC4_SET_FIELD(dsp5_mux, SCALER_DISPDITHER_DSP5_MUX));
+}
+
static void
vc4_atomic_complete_commit(struct drm_atomic_state *state)
{
@@ -157,12 +258,13 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
int i;
for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) {
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct vc4_crtc_state *vc4_crtc_state;
if (!new_crtc_state->commit)
continue;
- vc4_hvs_mask_underrun(dev, vc4_crtc->channel);
+ vc4_crtc_state = to_vc4_crtc_state(new_crtc_state);
+ vc4_hvs_mask_underrun(dev, vc4_crtc_state->assigned_channel);
}
if (vc4->hvs->hvs5)
@@ -176,6 +278,11 @@ vc4_atomic_complete_commit(struct drm_atomic_state *state)
vc4_ctm_commit(vc4, state);
+ if (vc4->hvs->hvs5)
+ vc5_hvs_pv_muxing_commit(vc4, state);
+ else
+ vc4_hvs_pv_muxing_commit(vc4, state);
+
drm_atomic_helper_commit_planes(dev, state, 0);
drm_atomic_helper_commit_modeset_enables(dev, state);
@@ -385,8 +492,11 @@ vc4_ctm_atomic_check(struct drm_device *dev, struct drm_atomic_state *state)
/* CTM is being enabled or the matrix changed. */
if (new_crtc_state->ctm) {
+ struct vc4_crtc_state *vc4_crtc_state =
+ to_vc4_crtc_state(new_crtc_state);
+
/* fifo is 1-based since 0 disables CTM. */
- int fifo = to_vc4_crtc(crtc)->channel + 1;
+ int fifo = vc4_crtc_state->assigned_channel + 1;
/* Check userland isn't trying to turn on CTM for more
* than one CRTC at a time.
@@ -496,10 +606,60 @@ static const struct drm_private_state_funcs vc4_load_tracker_state_funcs = {
.atomic_destroy_state = vc4_load_tracker_destroy_state,
};
+#define NUM_OUTPUTS 6
+#define NUM_CHANNELS 3
+
static int
vc4_atomic_check(struct drm_device *dev, struct drm_atomic_state *state)
{
- int ret;
+ unsigned long unassigned_channels = GENMASK(NUM_CHANNELS - 1, 0);
+ struct drm_crtc_state *crtc_state;
+ struct drm_crtc *crtc;
+ int i, ret;
+
+ for_each_new_crtc_in_state(state, crtc, crtc_state, i) {
+ struct vc4_crtc_state *vc4_crtc_state =
+ to_vc4_crtc_state(crtc_state);
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ unsigned int matching_channels;
+
+ if (!crtc_state->active)
+ continue;
+
+ /*
+ * The problem we have to solve here is that we have
+ * up to 7 encoders, connected to up to 6 CRTCs.
+ *
+ * Those CRTCs, depending on the instance, can be
+ * routed to 1, 2 or 3 HVS FIFOs, and we need to set
+ * the change the muxing between FIFOs and outputs in
+ * the HVS accordingly.
+ *
+ * It would be pretty hard to come up with an
+ * algorithm that would generically solve
+ * this. However, the current routing trees we support
+ * allow us to simplify a bit the problem.
+ *
+ * Indeed, with the current supported layouts, if we
+ * try to assign in the ascending crtc index order the
+ * FIFOs, we can't fall into the situation where an
+ * earlier CRTC that had multiple routes is assigned
+ * one that was the only option for a later CRTC.
+ *
+ * If the layout changes and doesn't give us that in
+ * the future, we will need to have something smarter,
+ * but it works so far.
+ */
+ matching_channels = unassigned_channels & vc4_crtc->data->hvs_available_channels;
+ if (matching_channels) {
+ unsigned int channel = ffs(matching_channels) - 1;
+
+ vc4_crtc_state->assigned_channel = channel;
+ unassigned_channels &= ~BIT(channel);
+ } else {
+ return -EINVAL;
+ }
+ }
ret = vc4_ctm_atomic_check(dev, state);
if (ret < 0)
diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h
index 91b785725555..7fbac68b6fe1 100644
--- a/drivers/gpu/drm/vc4/vc4_regs.h
+++ b/drivers/gpu/drm/vc4/vc4_regs.h
@@ -286,9 +286,19 @@
#define SCALER_DISPID 0x00000008
#define SCALER_DISPECTRL 0x0000000c
+# define SCALER_DISPECTRL_DSP2_MUX_SHIFT 31
+# define SCALER_DISPECTRL_DSP2_MUX_MASK VC4_MASK(31, 31)
+
#define SCALER_DISPPROF 0x00000010
+
#define SCALER_DISPDITHER 0x00000014
+# define SCALER_DISPDITHER_DSP5_MUX_SHIFT 30
+# define SCALER_DISPDITHER_DSP5_MUX_MASK VC4_MASK(31, 30)
+
#define SCALER_DISPEOLN 0x00000018
+# define SCALER_DISPEOLN_DSP4_MUX_SHIFT 30
+# define SCALER_DISPEOLN_DSP4_MUX_MASK VC4_MASK(31, 30)
+
#define SCALER_DISPLIST0 0x00000020
#define SCALER_DISPLIST1 0x00000024
#define SCALER_DISPLIST2 0x00000028
diff --git a/drivers/gpu/drm/vc4/vc4_txp.c b/drivers/gpu/drm/vc4/vc4_txp.c
index f39d9900d027..a2380d856000 100644
--- a/drivers/gpu/drm/vc4/vc4_txp.c
+++ b/drivers/gpu/drm/vc4/vc4_txp.c
@@ -452,6 +452,7 @@ static irqreturn_t vc4_txp_interrupt(int irq, void *data)
}
static const struct vc4_crtc_data vc4_txp_crtc_data = {
+ .hvs_available_channels = BIT(2),
.hvs_output = 2,
};
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 15/80] drm/vc4: crtc: Add FIFO depth to vc4_crtc_data
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Not all pixelvalve FIFOs in vc5 have the same depth, so we need to add that
to our vc4_crtc_data structure to be able to compute the fill level
properly later on.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 20 +++++++++++++++++---
drivers/gpu/drm/vc4/vc4_drv.h | 3 +++
2 files changed, 20 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index b7e47ce1476c..2c64efd2d3d9 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -206,10 +206,21 @@ void vc4_crtc_destroy(struct drm_crtc *crtc)
drm_crtc_cleanup(crtc);
}
-static u32 vc4_get_fifo_full_level(u32 format)
+static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
{
- static const u32 fifo_len_bytes = 64;
+ const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc);
+ u32 fifo_len_bytes = pv_data->fifo_depth;
+ /*
+ * Pixels are pulled from the HVS if the number of bytes is
+ * lower than the FIFO full level.
+ *
+ * The latency of the pixel fetch mechanism is 6 pixels, so we
+ * need to convert those 6 pixels in bytes, depending on the
+ * format, and then subtract that from the length of the FIFO
+ * to make sure we never end up in a situation where the FIFO
+ * is full.
+ */
switch (format) {
case PV_CONTROL_FORMAT_DSIV_16:
case PV_CONTROL_FORMAT_DSIC_16:
@@ -326,7 +337,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
CRTC_WRITE(PV_CONTROL,
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
- VC4_SET_FIELD(vc4_get_fifo_full_level(format),
+ VC4_SET_FIELD(vc4_get_fifo_full_level(vc4_crtc, format),
PV_CONTROL_FIFO_LEVEL) |
VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
PV_CONTROL_CLR_AT_START |
@@ -785,6 +796,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
.hvs_output = 0,
},
.debugfs_name = "crtc0_regs",
+ .fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI0,
@@ -798,6 +810,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
.hvs_output = 2,
},
.debugfs_name = "crtc1_regs",
+ .fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI1,
@@ -811,6 +824,7 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
.hvs_output = 1,
},
.debugfs_name = "crtc2_regs",
+ .fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI,
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 9e81ad8331f1..179010b9a010 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -457,6 +457,9 @@ struct vc4_crtc_data {
struct vc4_pv_data {
struct vc4_crtc_data base;
+ /* Depth of the PixelValve FIFO in bytes */
+ unsigned int fifo_depth;
+
/* Number of pixels output per clock period */
u8 pixels_per_clock;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 15/80] drm/vc4: crtc: Add FIFO depth to vc4_crtc_data
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Not all pixelvalve FIFOs in vc5 have the same depth, so we need to add that
to our vc4_crtc_data structure to be able to compute the fill level
properly later on.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 20 +++++++++++++++++---
drivers/gpu/drm/vc4/vc4_drv.h | 3 +++
2 files changed, 20 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index b7e47ce1476c..2c64efd2d3d9 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -206,10 +206,21 @@ void vc4_crtc_destroy(struct drm_crtc *crtc)
drm_crtc_cleanup(crtc);
}
-static u32 vc4_get_fifo_full_level(u32 format)
+static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
{
- static const u32 fifo_len_bytes = 64;
+ const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc);
+ u32 fifo_len_bytes = pv_data->fifo_depth;
+ /*
+ * Pixels are pulled from the HVS if the number of bytes is
+ * lower than the FIFO full level.
+ *
+ * The latency of the pixel fetch mechanism is 6 pixels, so we
+ * need to convert those 6 pixels in bytes, depending on the
+ * format, and then subtract that from the length of the FIFO
+ * to make sure we never end up in a situation where the FIFO
+ * is full.
+ */
switch (format) {
case PV_CONTROL_FORMAT_DSIV_16:
case PV_CONTROL_FORMAT_DSIC_16:
@@ -326,7 +337,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
CRTC_WRITE(PV_CONTROL,
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
- VC4_SET_FIELD(vc4_get_fifo_full_level(format),
+ VC4_SET_FIELD(vc4_get_fifo_full_level(vc4_crtc, format),
PV_CONTROL_FIFO_LEVEL) |
VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
PV_CONTROL_CLR_AT_START |
@@ -785,6 +796,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
.hvs_output = 0,
},
.debugfs_name = "crtc0_regs",
+ .fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI0,
@@ -798,6 +810,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
.hvs_output = 2,
},
.debugfs_name = "crtc1_regs",
+ .fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI1,
@@ -811,6 +824,7 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
.hvs_output = 1,
},
.debugfs_name = "crtc2_regs",
+ .fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI,
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 9e81ad8331f1..179010b9a010 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -457,6 +457,9 @@ struct vc4_crtc_data {
struct vc4_pv_data {
struct vc4_crtc_data base;
+ /* Depth of the PixelValve FIFO in bytes */
+ unsigned int fifo_depth;
+
/* Number of pixels output per clock period */
u8 pixels_per_clock;
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 15/80] drm/vc4: crtc: Add FIFO depth to vc4_crtc_data
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Not all pixelvalve FIFOs in vc5 have the same depth, so we need to add that
to our vc4_crtc_data structure to be able to compute the fill level
properly later on.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 20 +++++++++++++++++---
drivers/gpu/drm/vc4/vc4_drv.h | 3 +++
2 files changed, 20 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index b7e47ce1476c..2c64efd2d3d9 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -206,10 +206,21 @@ void vc4_crtc_destroy(struct drm_crtc *crtc)
drm_crtc_cleanup(crtc);
}
-static u32 vc4_get_fifo_full_level(u32 format)
+static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
{
- static const u32 fifo_len_bytes = 64;
+ const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc);
+ u32 fifo_len_bytes = pv_data->fifo_depth;
+ /*
+ * Pixels are pulled from the HVS if the number of bytes is
+ * lower than the FIFO full level.
+ *
+ * The latency of the pixel fetch mechanism is 6 pixels, so we
+ * need to convert those 6 pixels in bytes, depending on the
+ * format, and then subtract that from the length of the FIFO
+ * to make sure we never end up in a situation where the FIFO
+ * is full.
+ */
switch (format) {
case PV_CONTROL_FORMAT_DSIV_16:
case PV_CONTROL_FORMAT_DSIC_16:
@@ -326,7 +337,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
CRTC_WRITE(PV_CONTROL,
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
- VC4_SET_FIELD(vc4_get_fifo_full_level(format),
+ VC4_SET_FIELD(vc4_get_fifo_full_level(vc4_crtc, format),
PV_CONTROL_FIFO_LEVEL) |
VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
PV_CONTROL_CLR_AT_START |
@@ -785,6 +796,7 @@ static const struct vc4_pv_data bcm2835_pv0_data = {
.hvs_output = 0,
},
.debugfs_name = "crtc0_regs",
+ .fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI0,
@@ -798,6 +810,7 @@ static const struct vc4_pv_data bcm2835_pv1_data = {
.hvs_output = 2,
},
.debugfs_name = "crtc1_regs",
+ .fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI1,
@@ -811,6 +824,7 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
.hvs_output = 1,
},
.debugfs_name = "crtc2_regs",
+ .fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
[PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI,
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 9e81ad8331f1..179010b9a010 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -457,6 +457,9 @@ struct vc4_crtc_data {
struct vc4_pv_data {
struct vc4_crtc_data base;
+ /* Depth of the PixelValve FIFO in bytes */
+ unsigned int fifo_depth;
+
/* Number of pixels output per clock period */
u8 pixels_per_clock;
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 16/80] drm/vc4: crtc: Add function to compute FIFO level bits
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The longer FIFOs in vc5 pixelvalves means that the FIFO full level
doesn't fit in the original register field and that we also have a
secondary field. In order to prepare for this, let's move the registers
fill part to a helper function.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 2c64efd2d3d9..1d9e3658ae59 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -234,6 +234,15 @@ static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
}
}
+static u32 vc4_crtc_get_fifo_full_level_bits(struct vc4_crtc *vc4_crtc,
+ u32 format)
+{
+ u32 level = vc4_get_fifo_full_level(vc4_crtc, format);
+
+ return VC4_SET_FIELD(level & 0x3f,
+ PV_CONTROL_FIFO_LEVEL);
+}
+
/*
* Returns the encoder attached to the CRTC.
*
@@ -336,9 +345,8 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
CRTC_WRITE(PV_CONTROL,
+ vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) |
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
- VC4_SET_FIELD(vc4_get_fifo_full_level(vc4_crtc, format),
- PV_CONTROL_FIFO_LEVEL) |
VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
PV_CONTROL_CLR_AT_START |
PV_CONTROL_TRIGGER_UNDERFLOW |
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 16/80] drm/vc4: crtc: Add function to compute FIFO level bits
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The longer FIFOs in vc5 pixelvalves means that the FIFO full level
doesn't fit in the original register field and that we also have a
secondary field. In order to prepare for this, let's move the registers
fill part to a helper function.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 2c64efd2d3d9..1d9e3658ae59 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -234,6 +234,15 @@ static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
}
}
+static u32 vc4_crtc_get_fifo_full_level_bits(struct vc4_crtc *vc4_crtc,
+ u32 format)
+{
+ u32 level = vc4_get_fifo_full_level(vc4_crtc, format);
+
+ return VC4_SET_FIELD(level & 0x3f,
+ PV_CONTROL_FIFO_LEVEL);
+}
+
/*
* Returns the encoder attached to the CRTC.
*
@@ -336,9 +345,8 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
CRTC_WRITE(PV_CONTROL,
+ vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) |
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
- VC4_SET_FIELD(vc4_get_fifo_full_level(vc4_crtc, format),
- PV_CONTROL_FIFO_LEVEL) |
VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
PV_CONTROL_CLR_AT_START |
PV_CONTROL_TRIGGER_UNDERFLOW |
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 16/80] drm/vc4: crtc: Add function to compute FIFO level bits
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The longer FIFOs in vc5 pixelvalves means that the FIFO full level
doesn't fit in the original register field and that we also have a
secondary field. In order to prepare for this, let's move the registers
fill part to a helper function.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 2c64efd2d3d9..1d9e3658ae59 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -234,6 +234,15 @@ static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
}
}
+static u32 vc4_crtc_get_fifo_full_level_bits(struct vc4_crtc *vc4_crtc,
+ u32 format)
+{
+ u32 level = vc4_get_fifo_full_level(vc4_crtc, format);
+
+ return VC4_SET_FIELD(level & 0x3f,
+ PV_CONTROL_FIFO_LEVEL);
+}
+
/*
* Returns the encoder attached to the CRTC.
*
@@ -336,9 +345,8 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
CRTC_WRITE(PV_CONTROL,
+ vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) |
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
- VC4_SET_FIELD(vc4_get_fifo_full_level(vc4_crtc, format),
- PV_CONTROL_FIFO_LEVEL) |
VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
PV_CONTROL_CLR_AT_START |
PV_CONTROL_TRIGGER_UNDERFLOW |
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 17/80] drm/vc4: crtc: Rename HDMI encoder type to HDMI0
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The previous generations were only supporting a single HDMI controller, but
that's about to change, so put an index as well to differentiate between
the two controllers.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
drivers/gpu/drm/vc4/vc4_drv.h | 2 +-
drivers/gpu/drm/vc4/vc4_hdmi.c | 2 +-
3 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 1d9e3658ae59..04744223460a 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -835,7 +835,7 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
.fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
- [PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI,
+ [PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI0,
[PV_CONTROL_CLK_SELECT_VEC] = VC4_ENCODER_TYPE_VEC,
},
};
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 179010b9a010..5781773aec4b 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -426,7 +426,7 @@ to_vc4_plane_state(struct drm_plane_state *state)
enum vc4_encoder_type {
VC4_ENCODER_TYPE_NONE,
- VC4_ENCODER_TYPE_HDMI,
+ VC4_ENCODER_TYPE_HDMI0,
VC4_ENCODER_TYPE_VEC,
VC4_ENCODER_TYPE_DSI0,
VC4_ENCODER_TYPE_DSI1,
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 15a11cd4de25..ec34c08b16df 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -1309,7 +1309,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
GFP_KERNEL);
if (!vc4_hdmi_encoder)
return -ENOMEM;
- vc4_hdmi_encoder->base.type = VC4_ENCODER_TYPE_HDMI;
+ vc4_hdmi_encoder->base.type = VC4_ENCODER_TYPE_HDMI0;
hdmi->encoder = &vc4_hdmi_encoder->base.base;
hdmi->pdev = pdev;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 17/80] drm/vc4: crtc: Rename HDMI encoder type to HDMI0
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The previous generations were only supporting a single HDMI controller, but
that's about to change, so put an index as well to differentiate between
the two controllers.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
drivers/gpu/drm/vc4/vc4_drv.h | 2 +-
drivers/gpu/drm/vc4/vc4_hdmi.c | 2 +-
3 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 1d9e3658ae59..04744223460a 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -835,7 +835,7 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
.fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
- [PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI,
+ [PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI0,
[PV_CONTROL_CLK_SELECT_VEC] = VC4_ENCODER_TYPE_VEC,
},
};
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 179010b9a010..5781773aec4b 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -426,7 +426,7 @@ to_vc4_plane_state(struct drm_plane_state *state)
enum vc4_encoder_type {
VC4_ENCODER_TYPE_NONE,
- VC4_ENCODER_TYPE_HDMI,
+ VC4_ENCODER_TYPE_HDMI0,
VC4_ENCODER_TYPE_VEC,
VC4_ENCODER_TYPE_DSI0,
VC4_ENCODER_TYPE_DSI1,
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 15a11cd4de25..ec34c08b16df 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -1309,7 +1309,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
GFP_KERNEL);
if (!vc4_hdmi_encoder)
return -ENOMEM;
- vc4_hdmi_encoder->base.type = VC4_ENCODER_TYPE_HDMI;
+ vc4_hdmi_encoder->base.type = VC4_ENCODER_TYPE_HDMI0;
hdmi->encoder = &vc4_hdmi_encoder->base.base;
hdmi->pdev = pdev;
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 17/80] drm/vc4: crtc: Rename HDMI encoder type to HDMI0
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The previous generations were only supporting a single HDMI controller, but
that's about to change, so put an index as well to differentiate between
the two controllers.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
drivers/gpu/drm/vc4/vc4_drv.h | 2 +-
drivers/gpu/drm/vc4/vc4_hdmi.c | 2 +-
3 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 1d9e3658ae59..04744223460a 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -835,7 +835,7 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
.fifo_depth = 64,
.pixels_per_clock = 1,
.encoder_types = {
- [PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI,
+ [PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI0,
[PV_CONTROL_CLK_SELECT_VEC] = VC4_ENCODER_TYPE_VEC,
},
};
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 179010b9a010..5781773aec4b 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -426,7 +426,7 @@ to_vc4_plane_state(struct drm_plane_state *state)
enum vc4_encoder_type {
VC4_ENCODER_TYPE_NONE,
- VC4_ENCODER_TYPE_HDMI,
+ VC4_ENCODER_TYPE_HDMI0,
VC4_ENCODER_TYPE_VEC,
VC4_ENCODER_TYPE_DSI0,
VC4_ENCODER_TYPE_DSI1,
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 15a11cd4de25..ec34c08b16df 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -1309,7 +1309,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
GFP_KERNEL);
if (!vc4_hdmi_encoder)
return -ENOMEM;
- vc4_hdmi_encoder->base.type = VC4_ENCODER_TYPE_HDMI;
+ vc4_hdmi_encoder->base.type = VC4_ENCODER_TYPE_HDMI0;
hdmi->encoder = &vc4_hdmi_encoder->base.base;
hdmi->pdev = pdev;
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 18/80] drm/vc4: crtc: Add HDMI1 encoder type
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The BCM2711 sports a second HDMI controller, so let's add that second HDMI
encoder type.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 5781773aec4b..4126506b3a69 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -427,6 +427,7 @@ to_vc4_plane_state(struct drm_plane_state *state)
enum vc4_encoder_type {
VC4_ENCODER_TYPE_NONE,
VC4_ENCODER_TYPE_HDMI0,
+ VC4_ENCODER_TYPE_HDMI1,
VC4_ENCODER_TYPE_VEC,
VC4_ENCODER_TYPE_DSI0,
VC4_ENCODER_TYPE_DSI1,
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 18/80] drm/vc4: crtc: Add HDMI1 encoder type
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The BCM2711 sports a second HDMI controller, so let's add that second HDMI
encoder type.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 5781773aec4b..4126506b3a69 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -427,6 +427,7 @@ to_vc4_plane_state(struct drm_plane_state *state)
enum vc4_encoder_type {
VC4_ENCODER_TYPE_NONE,
VC4_ENCODER_TYPE_HDMI0,
+ VC4_ENCODER_TYPE_HDMI1,
VC4_ENCODER_TYPE_VEC,
VC4_ENCODER_TYPE_DSI0,
VC4_ENCODER_TYPE_DSI1,
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 18/80] drm/vc4: crtc: Add HDMI1 encoder type
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The BCM2711 sports a second HDMI controller, so let's add that second HDMI
encoder type.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 5781773aec4b..4126506b3a69 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -427,6 +427,7 @@ to_vc4_plane_state(struct drm_plane_state *state)
enum vc4_encoder_type {
VC4_ENCODER_TYPE_NONE,
VC4_ENCODER_TYPE_HDMI0,
+ VC4_ENCODER_TYPE_HDMI1,
VC4_ENCODER_TYPE_VEC,
VC4_ENCODER_TYPE_DSI0,
VC4_ENCODER_TYPE_DSI1,
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 19/80] drm/vc4: crtc: Disable color management for HVS5
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The HVS5 uses different color matrices. Disable color management support
for now.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 17 +++++++++++------
drivers/gpu/drm/vc4/vc4_hvs.c | 2 +-
2 files changed, 12 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 04744223460a..41bc61d5a61f 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -874,6 +874,7 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
const struct drm_crtc_funcs *crtc_funcs,
const struct drm_crtc_helper_funcs *crtc_helper_funcs)
{
+ struct vc4_dev *vc4 = to_vc4_dev(drm);
struct drm_crtc *crtc = &vc4_crtc->base;
struct drm_plane *primary_plane;
unsigned int i;
@@ -893,13 +894,17 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
crtc_funcs, NULL);
drm_crtc_helper_add(crtc, crtc_helper_funcs);
- drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
- drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
- /* We support CTM, but only for one CRTC at a time. It's therefore
- * implemented as private driver state in vc4_kms, not here.
- */
- drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size);
+ if (!vc4->hvs->hvs5) {
+ drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
+
+ drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
+
+ /* We support CTM, but only for one CRTC at a time. It's therefore
+ * implemented as private driver state in vc4_kms, not here.
+ */
+ drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size);
+ }
for (i = 0; i < crtc->gamma_size; i++) {
vc4_crtc->lut_r[i] = i;
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 31a9bc5ef84e..fa61cad3a53d 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -443,7 +443,7 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
SCALER_DISPBKGND_AUTOHS |
- SCALER_DISPBKGND_GAMMA |
+ ((!vc4->hvs->hvs5) ? SCALER_DISPBKGND_GAMMA : 0) |
(interlace ? SCALER_DISPBKGND_INTERLACE : 0));
/* Reload the LUT, since the SRAMs would have been disabled if
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 19/80] drm/vc4: crtc: Disable color management for HVS5
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The HVS5 uses different color matrices. Disable color management support
for now.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 17 +++++++++++------
drivers/gpu/drm/vc4/vc4_hvs.c | 2 +-
2 files changed, 12 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 04744223460a..41bc61d5a61f 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -874,6 +874,7 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
const struct drm_crtc_funcs *crtc_funcs,
const struct drm_crtc_helper_funcs *crtc_helper_funcs)
{
+ struct vc4_dev *vc4 = to_vc4_dev(drm);
struct drm_crtc *crtc = &vc4_crtc->base;
struct drm_plane *primary_plane;
unsigned int i;
@@ -893,13 +894,17 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
crtc_funcs, NULL);
drm_crtc_helper_add(crtc, crtc_helper_funcs);
- drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
- drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
- /* We support CTM, but only for one CRTC at a time. It's therefore
- * implemented as private driver state in vc4_kms, not here.
- */
- drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size);
+ if (!vc4->hvs->hvs5) {
+ drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
+
+ drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
+
+ /* We support CTM, but only for one CRTC at a time. It's therefore
+ * implemented as private driver state in vc4_kms, not here.
+ */
+ drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size);
+ }
for (i = 0; i < crtc->gamma_size; i++) {
vc4_crtc->lut_r[i] = i;
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 31a9bc5ef84e..fa61cad3a53d 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -443,7 +443,7 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
SCALER_DISPBKGND_AUTOHS |
- SCALER_DISPBKGND_GAMMA |
+ ((!vc4->hvs->hvs5) ? SCALER_DISPBKGND_GAMMA : 0) |
(interlace ? SCALER_DISPBKGND_INTERLACE : 0));
/* Reload the LUT, since the SRAMs would have been disabled if
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 19/80] drm/vc4: crtc: Disable color management for HVS5
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The HVS5 uses different color matrices. Disable color management support
for now.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 17 +++++++++++------
drivers/gpu/drm/vc4/vc4_hvs.c | 2 +-
2 files changed, 12 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 04744223460a..41bc61d5a61f 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -874,6 +874,7 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
const struct drm_crtc_funcs *crtc_funcs,
const struct drm_crtc_helper_funcs *crtc_helper_funcs)
{
+ struct vc4_dev *vc4 = to_vc4_dev(drm);
struct drm_crtc *crtc = &vc4_crtc->base;
struct drm_plane *primary_plane;
unsigned int i;
@@ -893,13 +894,17 @@ int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
crtc_funcs, NULL);
drm_crtc_helper_add(crtc, crtc_helper_funcs);
- drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
- drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
- /* We support CTM, but only for one CRTC at a time. It's therefore
- * implemented as private driver state in vc4_kms, not here.
- */
- drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size);
+ if (!vc4->hvs->hvs5) {
+ drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
+
+ drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size);
+
+ /* We support CTM, but only for one CRTC at a time. It's therefore
+ * implemented as private driver state in vc4_kms, not here.
+ */
+ drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size);
+ }
for (i = 0; i < crtc->gamma_size; i++) {
vc4_crtc->lut_r[i] = i;
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 31a9bc5ef84e..fa61cad3a53d 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -443,7 +443,7 @@ void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
SCALER_DISPBKGND_AUTOHS |
- SCALER_DISPBKGND_GAMMA |
+ ((!vc4->hvs->hvs5) ? SCALER_DISPBKGND_GAMMA : 0) |
(interlace ? SCALER_DISPBKGND_INTERLACE : 0));
/* Reload the LUT, since the SRAMs would have been disabled if
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 20/80] drm/vc4: crtc: Turn pixelvalve reset into a function
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The driver resets the pixelvalve FIFO in a number of occurences without
always using the same sequence.
Since this will be critical for BCM2711, let's move that sequence to a
function so that we are consistent.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 20 +++++++++++++-------
1 file changed, 13 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 41bc61d5a61f..c2ab907611e3 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -267,6 +267,15 @@ static struct drm_encoder *vc4_get_crtc_encoder(struct drm_crtc *crtc)
return NULL;
}
+static void vc4_crtc_pixelvalve_reset(struct drm_crtc *crtc)
+{
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+
+ /* The PV needs to be disabled before it can be flushed */
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_FIFO_CLR);
+}
+
static void vc4_crtc_config_pv(struct drm_crtc *crtc)
{
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
@@ -282,10 +291,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
u8 ppc = pv_data->pixels_per_clock;
- /* Reset the PV fifo. */
- CRTC_WRITE(PV_CONTROL, 0);
- CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);
- CRTC_WRITE(PV_CONTROL, 0);
+ vc4_crtc_pixelvalve_reset(crtc);
CRTC_WRITE(PV_HORZA,
VC4_SET_FIELD((mode->htotal - mode->hsync_end) * pixel_rep / ppc,
@@ -430,9 +436,9 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
- /* Reset the PV fifo. */
- CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) |
- PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);
+ vc4_crtc_pixelvalve_reset(crtc);
+
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
/* Enable vblank irq handling before crtc is started otherwise
* drm_crtc_get_vblank() fails in vc4_crtc_update_dlist().
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 20/80] drm/vc4: crtc: Turn pixelvalve reset into a function
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The driver resets the pixelvalve FIFO in a number of occurences without
always using the same sequence.
Since this will be critical for BCM2711, let's move that sequence to a
function so that we are consistent.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 20 +++++++++++++-------
1 file changed, 13 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 41bc61d5a61f..c2ab907611e3 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -267,6 +267,15 @@ static struct drm_encoder *vc4_get_crtc_encoder(struct drm_crtc *crtc)
return NULL;
}
+static void vc4_crtc_pixelvalve_reset(struct drm_crtc *crtc)
+{
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+
+ /* The PV needs to be disabled before it can be flushed */
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_FIFO_CLR);
+}
+
static void vc4_crtc_config_pv(struct drm_crtc *crtc)
{
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
@@ -282,10 +291,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
u8 ppc = pv_data->pixels_per_clock;
- /* Reset the PV fifo. */
- CRTC_WRITE(PV_CONTROL, 0);
- CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);
- CRTC_WRITE(PV_CONTROL, 0);
+ vc4_crtc_pixelvalve_reset(crtc);
CRTC_WRITE(PV_HORZA,
VC4_SET_FIELD((mode->htotal - mode->hsync_end) * pixel_rep / ppc,
@@ -430,9 +436,9 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
- /* Reset the PV fifo. */
- CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) |
- PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);
+ vc4_crtc_pixelvalve_reset(crtc);
+
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
/* Enable vblank irq handling before crtc is started otherwise
* drm_crtc_get_vblank() fails in vc4_crtc_update_dlist().
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 20/80] drm/vc4: crtc: Turn pixelvalve reset into a function
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The driver resets the pixelvalve FIFO in a number of occurences without
always using the same sequence.
Since this will be critical for BCM2711, let's move that sequence to a
function so that we are consistent.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 20 +++++++++++++-------
1 file changed, 13 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 41bc61d5a61f..c2ab907611e3 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -267,6 +267,15 @@ static struct drm_encoder *vc4_get_crtc_encoder(struct drm_crtc *crtc)
return NULL;
}
+static void vc4_crtc_pixelvalve_reset(struct drm_crtc *crtc)
+{
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+
+ /* The PV needs to be disabled before it can be flushed */
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_FIFO_CLR);
+}
+
static void vc4_crtc_config_pv(struct drm_crtc *crtc)
{
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
@@ -282,10 +291,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
u8 ppc = pv_data->pixels_per_clock;
- /* Reset the PV fifo. */
- CRTC_WRITE(PV_CONTROL, 0);
- CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);
- CRTC_WRITE(PV_CONTROL, 0);
+ vc4_crtc_pixelvalve_reset(crtc);
CRTC_WRITE(PV_HORZA,
VC4_SET_FIELD((mode->htotal - mode->hsync_end) * pixel_rep / ppc,
@@ -430,9 +436,9 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
- /* Reset the PV fifo. */
- CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) |
- PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);
+ vc4_crtc_pixelvalve_reset(crtc);
+
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
/* Enable vblank irq handling before crtc is started otherwise
* drm_crtc_get_vblank() fails in vc4_crtc_update_dlist().
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 21/80] drm/vc4: crtc: Move PV dump to config_pv
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Now that we only configure the PixelValve in vc4_crtc_config_pv, it doesn't
really make much sense to dump its register content in its caller.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 26 ++++++++++++--------------
1 file changed, 12 insertions(+), 14 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index c2ab907611e3..181d3fd57bc7 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -290,6 +290,14 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
u8 ppc = pv_data->pixels_per_clock;
+ bool debug_dump_regs = false;
+
+ if (debug_dump_regs) {
+ struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev);
+ dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs before:\n",
+ drm_crtc_index(crtc));
+ drm_print_regset32(&p, &vc4_crtc->regset);
+ }
vc4_crtc_pixelvalve_reset(crtc);
@@ -359,30 +367,20 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
PV_CONTROL_WAIT_HSTART |
VC4_SET_FIELD(vc4_encoder->clock_select,
PV_CONTROL_CLK_SELECT));
-}
-
-static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
-{
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
- bool debug_dump_regs = false;
if (debug_dump_regs) {
struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev);
- dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs before:\n",
+ dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs after:\n",
drm_crtc_index(crtc));
drm_print_regset32(&p, &vc4_crtc->regset);
}
+}
+static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
+{
vc4_crtc_config_pv(crtc);
vc4_hvs_mode_set_nofb(crtc);
-
- if (debug_dump_regs) {
- struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev);
- dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs after:\n",
- drm_crtc_index(crtc));
- drm_print_regset32(&p, &vc4_crtc->regset);
- }
}
static void require_hvs_enabled(struct drm_device *dev)
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 21/80] drm/vc4: crtc: Move PV dump to config_pv
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Now that we only configure the PixelValve in vc4_crtc_config_pv, it doesn't
really make much sense to dump its register content in its caller.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 26 ++++++++++++--------------
1 file changed, 12 insertions(+), 14 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index c2ab907611e3..181d3fd57bc7 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -290,6 +290,14 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
u8 ppc = pv_data->pixels_per_clock;
+ bool debug_dump_regs = false;
+
+ if (debug_dump_regs) {
+ struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev);
+ dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs before:\n",
+ drm_crtc_index(crtc));
+ drm_print_regset32(&p, &vc4_crtc->regset);
+ }
vc4_crtc_pixelvalve_reset(crtc);
@@ -359,30 +367,20 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
PV_CONTROL_WAIT_HSTART |
VC4_SET_FIELD(vc4_encoder->clock_select,
PV_CONTROL_CLK_SELECT));
-}
-
-static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
-{
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
- bool debug_dump_regs = false;
if (debug_dump_regs) {
struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev);
- dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs before:\n",
+ dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs after:\n",
drm_crtc_index(crtc));
drm_print_regset32(&p, &vc4_crtc->regset);
}
+}
+static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
+{
vc4_crtc_config_pv(crtc);
vc4_hvs_mode_set_nofb(crtc);
-
- if (debug_dump_regs) {
- struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev);
- dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs after:\n",
- drm_crtc_index(crtc));
- drm_print_regset32(&p, &vc4_crtc->regset);
- }
}
static void require_hvs_enabled(struct drm_device *dev)
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 21/80] drm/vc4: crtc: Move PV dump to config_pv
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Now that we only configure the PixelValve in vc4_crtc_config_pv, it doesn't
really make much sense to dump its register content in its caller.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 26 ++++++++++++--------------
1 file changed, 12 insertions(+), 14 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index c2ab907611e3..181d3fd57bc7 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -290,6 +290,14 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
u8 ppc = pv_data->pixels_per_clock;
+ bool debug_dump_regs = false;
+
+ if (debug_dump_regs) {
+ struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev);
+ dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs before:\n",
+ drm_crtc_index(crtc));
+ drm_print_regset32(&p, &vc4_crtc->regset);
+ }
vc4_crtc_pixelvalve_reset(crtc);
@@ -359,30 +367,20 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
PV_CONTROL_WAIT_HSTART |
VC4_SET_FIELD(vc4_encoder->clock_select,
PV_CONTROL_CLK_SELECT));
-}
-
-static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
-{
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
- bool debug_dump_regs = false;
if (debug_dump_regs) {
struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev);
- dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs before:\n",
+ dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs after:\n",
drm_crtc_index(crtc));
drm_print_regset32(&p, &vc4_crtc->regset);
}
+}
+static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
+{
vc4_crtc_config_pv(crtc);
vc4_hvs_mode_set_nofb(crtc);
-
- if (debug_dump_regs) {
- struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev);
- dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs after:\n",
- drm_crtc_index(crtc));
- drm_print_regset32(&p, &vc4_crtc->regset);
- }
}
static void require_hvs_enabled(struct drm_device *dev)
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 22/80] drm/vc4: crtc: Move HVS init and close to a function
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
In order to make further refactoring easier, let's move the HVS channel
setup / teardown to their own function.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hvs.c | 104 +++++++++++++++++++----------------
1 file changed, 58 insertions(+), 46 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index fa61cad3a53d..dde931233d4a 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -196,6 +196,62 @@ static void vc4_hvs_update_gamma_lut(struct drm_crtc *crtc)
vc4_hvs_lut_load(crtc);
}
+static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
+ struct drm_display_mode *mode, bool oneshot)
+{
+ struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state);
+ unsigned int chan = vc4_crtc_state->assigned_channel;
+ u32 dispctrl;
+
+ /* Turn on the scaler, which will wait for vstart to start
+ * compositing.
+ * When feeding the transposer, we should operate in oneshot
+ * mode.
+ */
+ dispctrl = SCALER_DISPCTRLX_ENABLE;
+
+ if (!vc4->hvs->hvs5)
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
+ else
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER5_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER5_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
+
+ HVS_WRITE(SCALER_DISPCTRLX(chan), dispctrl);
+
+ return 0;
+}
+
+static void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int chan)
+{
+ struct vc4_dev *vc4 = to_vc4_dev(dev);
+
+ if (HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_ENABLE)
+ return;
+
+ HVS_WRITE(SCALER_DISPCTRLX(chan),
+ HVS_READ(SCALER_DISPCTRLX(chan)) | SCALER_DISPCTRLX_RESET);
+ HVS_WRITE(SCALER_DISPCTRLX(chan),
+ HVS_READ(SCALER_DISPCTRLX(chan)) & ~SCALER_DISPCTRLX_ENABLE);
+
+ /* Once we leave, the scaler should be disabled and its fifo empty. */
+ WARN_ON_ONCE(HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_RESET);
+
+ WARN_ON_ONCE(VC4_GET_FIELD(HVS_READ(SCALER_DISPSTATX(chan)),
+ SCALER_DISPSTATX_MODE) !=
+ SCALER_DISPSTATX_MODE_DISABLED);
+
+ WARN_ON_ONCE((HVS_READ(SCALER_DISPSTATX(chan)) &
+ (SCALER_DISPSTATX_FULL | SCALER_DISPSTATX_EMPTY)) !=
+ SCALER_DISPSTATX_EMPTY);
+}
+
int vc4_hvs_atomic_check(struct drm_crtc *crtc,
struct drm_crtc_state *state)
{
@@ -268,63 +324,19 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool oneshot = vc4_state->feed_txp;
- u32 dispctrl;
vc4_hvs_update_dlist(crtc);
-
- /* Turn on the scaler, which will wait for vstart to start
- * compositing.
- * When feeding the transposer, we should operate in oneshot
- * mode.
- */
- dispctrl = SCALER_DISPCTRLX_ENABLE;
-
- if (!vc4->hvs->hvs5)
- dispctrl |= VC4_SET_FIELD(mode->hdisplay,
- SCALER_DISPCTRLX_WIDTH) |
- VC4_SET_FIELD(mode->vdisplay,
- SCALER_DISPCTRLX_HEIGHT) |
- (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
- else
- dispctrl |= VC4_SET_FIELD(mode->hdisplay,
- SCALER5_DISPCTRLX_WIDTH) |
- VC4_SET_FIELD(mode->vdisplay,
- SCALER5_DISPCTRLX_HEIGHT) |
- (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
-
- HVS_WRITE(SCALER_DISPCTRLX(vc4_state->assigned_channel), dispctrl);
+ vc4_hvs_init_channel(vc4, crtc, mode, oneshot);
}
void vc4_hvs_atomic_disable(struct drm_crtc *crtc,
struct drm_crtc_state *old_state)
{
struct drm_device *dev = crtc->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(old_state);
unsigned int chan = vc4_state->assigned_channel;
- if (HVS_READ(SCALER_DISPCTRLX(chan)) &
- SCALER_DISPCTRLX_ENABLE) {
- HVS_WRITE(SCALER_DISPCTRLX(chan),
- SCALER_DISPCTRLX_RESET);
-
- /* While the docs say that reset is self-clearing, it
- * seems it doesn't actually.
- */
- HVS_WRITE(SCALER_DISPCTRLX(chan), 0);
- }
-
- /* Once we leave, the scaler should be disabled and its fifo empty. */
-
- WARN_ON_ONCE(HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_RESET);
-
- WARN_ON_ONCE(VC4_GET_FIELD(HVS_READ(SCALER_DISPSTATX(chan)),
- SCALER_DISPSTATX_MODE) !=
- SCALER_DISPSTATX_MODE_DISABLED);
-
- WARN_ON_ONCE((HVS_READ(SCALER_DISPSTATX(chan)) &
- (SCALER_DISPSTATX_FULL | SCALER_DISPSTATX_EMPTY)) !=
- SCALER_DISPSTATX_EMPTY);
+ vc4_hvs_stop_channel(dev, chan);
}
void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 22/80] drm/vc4: crtc: Move HVS init and close to a function
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to make further refactoring easier, let's move the HVS channel
setup / teardown to their own function.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hvs.c | 104 +++++++++++++++++++----------------
1 file changed, 58 insertions(+), 46 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index fa61cad3a53d..dde931233d4a 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -196,6 +196,62 @@ static void vc4_hvs_update_gamma_lut(struct drm_crtc *crtc)
vc4_hvs_lut_load(crtc);
}
+static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
+ struct drm_display_mode *mode, bool oneshot)
+{
+ struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state);
+ unsigned int chan = vc4_crtc_state->assigned_channel;
+ u32 dispctrl;
+
+ /* Turn on the scaler, which will wait for vstart to start
+ * compositing.
+ * When feeding the transposer, we should operate in oneshot
+ * mode.
+ */
+ dispctrl = SCALER_DISPCTRLX_ENABLE;
+
+ if (!vc4->hvs->hvs5)
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
+ else
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER5_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER5_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
+
+ HVS_WRITE(SCALER_DISPCTRLX(chan), dispctrl);
+
+ return 0;
+}
+
+static void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int chan)
+{
+ struct vc4_dev *vc4 = to_vc4_dev(dev);
+
+ if (HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_ENABLE)
+ return;
+
+ HVS_WRITE(SCALER_DISPCTRLX(chan),
+ HVS_READ(SCALER_DISPCTRLX(chan)) | SCALER_DISPCTRLX_RESET);
+ HVS_WRITE(SCALER_DISPCTRLX(chan),
+ HVS_READ(SCALER_DISPCTRLX(chan)) & ~SCALER_DISPCTRLX_ENABLE);
+
+ /* Once we leave, the scaler should be disabled and its fifo empty. */
+ WARN_ON_ONCE(HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_RESET);
+
+ WARN_ON_ONCE(VC4_GET_FIELD(HVS_READ(SCALER_DISPSTATX(chan)),
+ SCALER_DISPSTATX_MODE) !=
+ SCALER_DISPSTATX_MODE_DISABLED);
+
+ WARN_ON_ONCE((HVS_READ(SCALER_DISPSTATX(chan)) &
+ (SCALER_DISPSTATX_FULL | SCALER_DISPSTATX_EMPTY)) !=
+ SCALER_DISPSTATX_EMPTY);
+}
+
int vc4_hvs_atomic_check(struct drm_crtc *crtc,
struct drm_crtc_state *state)
{
@@ -268,63 +324,19 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool oneshot = vc4_state->feed_txp;
- u32 dispctrl;
vc4_hvs_update_dlist(crtc);
-
- /* Turn on the scaler, which will wait for vstart to start
- * compositing.
- * When feeding the transposer, we should operate in oneshot
- * mode.
- */
- dispctrl = SCALER_DISPCTRLX_ENABLE;
-
- if (!vc4->hvs->hvs5)
- dispctrl |= VC4_SET_FIELD(mode->hdisplay,
- SCALER_DISPCTRLX_WIDTH) |
- VC4_SET_FIELD(mode->vdisplay,
- SCALER_DISPCTRLX_HEIGHT) |
- (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
- else
- dispctrl |= VC4_SET_FIELD(mode->hdisplay,
- SCALER5_DISPCTRLX_WIDTH) |
- VC4_SET_FIELD(mode->vdisplay,
- SCALER5_DISPCTRLX_HEIGHT) |
- (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
-
- HVS_WRITE(SCALER_DISPCTRLX(vc4_state->assigned_channel), dispctrl);
+ vc4_hvs_init_channel(vc4, crtc, mode, oneshot);
}
void vc4_hvs_atomic_disable(struct drm_crtc *crtc,
struct drm_crtc_state *old_state)
{
struct drm_device *dev = crtc->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(old_state);
unsigned int chan = vc4_state->assigned_channel;
- if (HVS_READ(SCALER_DISPCTRLX(chan)) &
- SCALER_DISPCTRLX_ENABLE) {
- HVS_WRITE(SCALER_DISPCTRLX(chan),
- SCALER_DISPCTRLX_RESET);
-
- /* While the docs say that reset is self-clearing, it
- * seems it doesn't actually.
- */
- HVS_WRITE(SCALER_DISPCTRLX(chan), 0);
- }
-
- /* Once we leave, the scaler should be disabled and its fifo empty. */
-
- WARN_ON_ONCE(HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_RESET);
-
- WARN_ON_ONCE(VC4_GET_FIELD(HVS_READ(SCALER_DISPSTATX(chan)),
- SCALER_DISPSTATX_MODE) !=
- SCALER_DISPSTATX_MODE_DISABLED);
-
- WARN_ON_ONCE((HVS_READ(SCALER_DISPSTATX(chan)) &
- (SCALER_DISPSTATX_FULL | SCALER_DISPSTATX_EMPTY)) !=
- SCALER_DISPSTATX_EMPTY);
+ vc4_hvs_stop_channel(dev, chan);
}
void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 22/80] drm/vc4: crtc: Move HVS init and close to a function
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to make further refactoring easier, let's move the HVS channel
setup / teardown to their own function.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hvs.c | 104 +++++++++++++++++++----------------
1 file changed, 58 insertions(+), 46 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index fa61cad3a53d..dde931233d4a 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -196,6 +196,62 @@ static void vc4_hvs_update_gamma_lut(struct drm_crtc *crtc)
vc4_hvs_lut_load(crtc);
}
+static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
+ struct drm_display_mode *mode, bool oneshot)
+{
+ struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state);
+ unsigned int chan = vc4_crtc_state->assigned_channel;
+ u32 dispctrl;
+
+ /* Turn on the scaler, which will wait for vstart to start
+ * compositing.
+ * When feeding the transposer, we should operate in oneshot
+ * mode.
+ */
+ dispctrl = SCALER_DISPCTRLX_ENABLE;
+
+ if (!vc4->hvs->hvs5)
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
+ else
+ dispctrl |= VC4_SET_FIELD(mode->hdisplay,
+ SCALER5_DISPCTRLX_WIDTH) |
+ VC4_SET_FIELD(mode->vdisplay,
+ SCALER5_DISPCTRLX_HEIGHT) |
+ (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
+
+ HVS_WRITE(SCALER_DISPCTRLX(chan), dispctrl);
+
+ return 0;
+}
+
+static void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int chan)
+{
+ struct vc4_dev *vc4 = to_vc4_dev(dev);
+
+ if (HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_ENABLE)
+ return;
+
+ HVS_WRITE(SCALER_DISPCTRLX(chan),
+ HVS_READ(SCALER_DISPCTRLX(chan)) | SCALER_DISPCTRLX_RESET);
+ HVS_WRITE(SCALER_DISPCTRLX(chan),
+ HVS_READ(SCALER_DISPCTRLX(chan)) & ~SCALER_DISPCTRLX_ENABLE);
+
+ /* Once we leave, the scaler should be disabled and its fifo empty. */
+ WARN_ON_ONCE(HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_RESET);
+
+ WARN_ON_ONCE(VC4_GET_FIELD(HVS_READ(SCALER_DISPSTATX(chan)),
+ SCALER_DISPSTATX_MODE) !=
+ SCALER_DISPSTATX_MODE_DISABLED);
+
+ WARN_ON_ONCE((HVS_READ(SCALER_DISPSTATX(chan)) &
+ (SCALER_DISPSTATX_FULL | SCALER_DISPSTATX_EMPTY)) !=
+ SCALER_DISPSTATX_EMPTY);
+}
+
int vc4_hvs_atomic_check(struct drm_crtc *crtc,
struct drm_crtc_state *state)
{
@@ -268,63 +324,19 @@ void vc4_hvs_atomic_enable(struct drm_crtc *crtc,
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
bool oneshot = vc4_state->feed_txp;
- u32 dispctrl;
vc4_hvs_update_dlist(crtc);
-
- /* Turn on the scaler, which will wait for vstart to start
- * compositing.
- * When feeding the transposer, we should operate in oneshot
- * mode.
- */
- dispctrl = SCALER_DISPCTRLX_ENABLE;
-
- if (!vc4->hvs->hvs5)
- dispctrl |= VC4_SET_FIELD(mode->hdisplay,
- SCALER_DISPCTRLX_WIDTH) |
- VC4_SET_FIELD(mode->vdisplay,
- SCALER_DISPCTRLX_HEIGHT) |
- (oneshot ? SCALER_DISPCTRLX_ONESHOT : 0);
- else
- dispctrl |= VC4_SET_FIELD(mode->hdisplay,
- SCALER5_DISPCTRLX_WIDTH) |
- VC4_SET_FIELD(mode->vdisplay,
- SCALER5_DISPCTRLX_HEIGHT) |
- (oneshot ? SCALER5_DISPCTRLX_ONESHOT : 0);
-
- HVS_WRITE(SCALER_DISPCTRLX(vc4_state->assigned_channel), dispctrl);
+ vc4_hvs_init_channel(vc4, crtc, mode, oneshot);
}
void vc4_hvs_atomic_disable(struct drm_crtc *crtc,
struct drm_crtc_state *old_state)
{
struct drm_device *dev = crtc->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(old_state);
unsigned int chan = vc4_state->assigned_channel;
- if (HVS_READ(SCALER_DISPCTRLX(chan)) &
- SCALER_DISPCTRLX_ENABLE) {
- HVS_WRITE(SCALER_DISPCTRLX(chan),
- SCALER_DISPCTRLX_RESET);
-
- /* While the docs say that reset is self-clearing, it
- * seems it doesn't actually.
- */
- HVS_WRITE(SCALER_DISPCTRLX(chan), 0);
- }
-
- /* Once we leave, the scaler should be disabled and its fifo empty. */
-
- WARN_ON_ONCE(HVS_READ(SCALER_DISPCTRLX(chan)) & SCALER_DISPCTRLX_RESET);
-
- WARN_ON_ONCE(VC4_GET_FIELD(HVS_READ(SCALER_DISPSTATX(chan)),
- SCALER_DISPSTATX_MODE) !=
- SCALER_DISPSTATX_MODE_DISABLED);
-
- WARN_ON_ONCE((HVS_READ(SCALER_DISPSTATX(chan)) &
- (SCALER_DISPSTATX_FULL | SCALER_DISPSTATX_EMPTY)) !=
- SCALER_DISPSTATX_EMPTY);
+ vc4_hvs_stop_channel(dev, chan);
}
void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 23/80] drm/vc4: crtc: Move the HVS gamma LUT setup to our init function
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Since most of the HVS channel is setup in the init function, let's move the
gamma setup there too. As this makes the HVS mode_set function empty, let's
remove it in the process.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
drivers/gpu/drm/vc4/vc4_drv.h | 1 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 59 +++++++++--------------------------
drivers/gpu/drm/vc4/vc4_txp.c | 1 +-
4 files changed, 16 insertions(+), 47 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 181d3fd57bc7..284a85b9d7d4 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -379,8 +379,6 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
{
vc4_crtc_config_pv(crtc);
-
- vc4_hvs_mode_set_nofb(crtc);
}
static void require_hvs_enabled(struct drm_device *dev)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 4126506b3a69..dfcc684f5d28 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -904,7 +904,6 @@ int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_crtc_state *state);
void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_flush(struct drm_crtc *crtc, struct drm_crtc_state *state);
-void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc);
void vc4_hvs_dump_state(struct drm_device *dev);
void vc4_hvs_unmask_underrun(struct drm_device *dev, int channel);
void vc4_hvs_mask_underrun(struct drm_device *dev, int channel);
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index dde931233d4a..efaae60bb323 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -201,6 +201,8 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
{
struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state);
unsigned int chan = vc4_crtc_state->assigned_channel;
+ bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
+ u32 dispbkgndx;
u32 dispctrl;
/* Turn on the scaler, which will wait for vstart to start
@@ -225,6 +227,20 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
HVS_WRITE(SCALER_DISPCTRLX(chan), dispctrl);
+ dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(chan));
+ dispbkgndx &= ~SCALER_DISPBKGND_GAMMA;
+ dispbkgndx &= ~SCALER_DISPBKGND_INTERLACE;
+
+ HVS_WRITE(SCALER_DISPBKGNDX(chan), dispbkgndx |
+ SCALER_DISPBKGND_AUTOHS |
+ ((!vc4->hvs->hvs5) ? SCALER_DISPBKGND_GAMMA : 0) |
+ (interlace ? SCALER_DISPBKGND_INTERLACE : 0));
+
+ /* Reload the LUT, since the SRAMs would have been disabled if
+ * all CRTCs had SCALER_DISPBKGND_GAMMA unset at once.
+ */
+ vc4_hvs_lut_load(crtc);
+
return 0;
}
@@ -421,49 +437,6 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
}
}
-void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
-{
- struct drm_device *dev = crtc->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
- struct drm_display_mode *mode = &crtc->state->adjusted_mode;
- bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
-
- if (vc4_state->assigned_channel == 2) {
- u32 dispctrl;
- u32 dsp3_mux;
-
- /*
- * SCALER_DISPCTRL_DSP3 = X, where X < 2 means 'connect DSP3 to
- * FIFO X'.
- * SCALER_DISPCTRL_DSP3 = 3 means 'disable DSP 3'.
- *
- * DSP3 is connected to FIFO2 unless the transposer is
- * enabled. In this case, FIFO 2 is directly accessed by the
- * TXP IP, and we need to disable the FIFO2 -> pixelvalve1
- * route.
- */
- if (vc4_state->feed_txp)
- dsp3_mux = VC4_SET_FIELD(3, SCALER_DISPCTRL_DSP3_MUX);
- else
- dsp3_mux = VC4_SET_FIELD(2, SCALER_DISPCTRL_DSP3_MUX);
-
- dispctrl = HVS_READ(SCALER_DISPCTRL) &
- ~SCALER_DISPCTRL_DSP3_MUX_MASK;
- HVS_WRITE(SCALER_DISPCTRL, dispctrl | dsp3_mux);
- }
-
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
- SCALER_DISPBKGND_AUTOHS |
- ((!vc4->hvs->hvs5) ? SCALER_DISPBKGND_GAMMA : 0) |
- (interlace ? SCALER_DISPBKGND_INTERLACE : 0));
-
- /* Reload the LUT, since the SRAMs would have been disabled if
- * all CRTCs had SCALER_DISPBKGND_GAMMA unset at once.
- */
- vc4_hvs_lut_load(crtc);
-}
-
void vc4_hvs_mask_underrun(struct drm_device *dev, int channel)
{
struct vc4_dev *vc4 = to_vc4_dev(dev);
diff --git a/drivers/gpu/drm/vc4/vc4_txp.c b/drivers/gpu/drm/vc4/vc4_txp.c
index a2380d856000..849dcafbfff1 100644
--- a/drivers/gpu/drm/vc4/vc4_txp.c
+++ b/drivers/gpu/drm/vc4/vc4_txp.c
@@ -436,7 +436,6 @@ static const struct drm_crtc_helper_funcs vc4_txp_crtc_helper_funcs = {
.atomic_flush = vc4_hvs_atomic_flush,
.atomic_enable = vc4_txp_atomic_enable,
.atomic_disable = vc4_txp_atomic_disable,
- .mode_set_nofb = vc4_hvs_mode_set_nofb,
};
static irqreturn_t vc4_txp_interrupt(int irq, void *data)
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 23/80] drm/vc4: crtc: Move the HVS gamma LUT setup to our init function
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Since most of the HVS channel is setup in the init function, let's move the
gamma setup there too. As this makes the HVS mode_set function empty, let's
remove it in the process.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
drivers/gpu/drm/vc4/vc4_drv.h | 1 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 59 +++++++++--------------------------
drivers/gpu/drm/vc4/vc4_txp.c | 1 +-
4 files changed, 16 insertions(+), 47 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 181d3fd57bc7..284a85b9d7d4 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -379,8 +379,6 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
{
vc4_crtc_config_pv(crtc);
-
- vc4_hvs_mode_set_nofb(crtc);
}
static void require_hvs_enabled(struct drm_device *dev)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 4126506b3a69..dfcc684f5d28 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -904,7 +904,6 @@ int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_crtc_state *state);
void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_flush(struct drm_crtc *crtc, struct drm_crtc_state *state);
-void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc);
void vc4_hvs_dump_state(struct drm_device *dev);
void vc4_hvs_unmask_underrun(struct drm_device *dev, int channel);
void vc4_hvs_mask_underrun(struct drm_device *dev, int channel);
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index dde931233d4a..efaae60bb323 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -201,6 +201,8 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
{
struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state);
unsigned int chan = vc4_crtc_state->assigned_channel;
+ bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
+ u32 dispbkgndx;
u32 dispctrl;
/* Turn on the scaler, which will wait for vstart to start
@@ -225,6 +227,20 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
HVS_WRITE(SCALER_DISPCTRLX(chan), dispctrl);
+ dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(chan));
+ dispbkgndx &= ~SCALER_DISPBKGND_GAMMA;
+ dispbkgndx &= ~SCALER_DISPBKGND_INTERLACE;
+
+ HVS_WRITE(SCALER_DISPBKGNDX(chan), dispbkgndx |
+ SCALER_DISPBKGND_AUTOHS |
+ ((!vc4->hvs->hvs5) ? SCALER_DISPBKGND_GAMMA : 0) |
+ (interlace ? SCALER_DISPBKGND_INTERLACE : 0));
+
+ /* Reload the LUT, since the SRAMs would have been disabled if
+ * all CRTCs had SCALER_DISPBKGND_GAMMA unset at once.
+ */
+ vc4_hvs_lut_load(crtc);
+
return 0;
}
@@ -421,49 +437,6 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
}
}
-void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
-{
- struct drm_device *dev = crtc->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
- struct drm_display_mode *mode = &crtc->state->adjusted_mode;
- bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
-
- if (vc4_state->assigned_channel == 2) {
- u32 dispctrl;
- u32 dsp3_mux;
-
- /*
- * SCALER_DISPCTRL_DSP3 = X, where X < 2 means 'connect DSP3 to
- * FIFO X'.
- * SCALER_DISPCTRL_DSP3 = 3 means 'disable DSP 3'.
- *
- * DSP3 is connected to FIFO2 unless the transposer is
- * enabled. In this case, FIFO 2 is directly accessed by the
- * TXP IP, and we need to disable the FIFO2 -> pixelvalve1
- * route.
- */
- if (vc4_state->feed_txp)
- dsp3_mux = VC4_SET_FIELD(3, SCALER_DISPCTRL_DSP3_MUX);
- else
- dsp3_mux = VC4_SET_FIELD(2, SCALER_DISPCTRL_DSP3_MUX);
-
- dispctrl = HVS_READ(SCALER_DISPCTRL) &
- ~SCALER_DISPCTRL_DSP3_MUX_MASK;
- HVS_WRITE(SCALER_DISPCTRL, dispctrl | dsp3_mux);
- }
-
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
- SCALER_DISPBKGND_AUTOHS |
- ((!vc4->hvs->hvs5) ? SCALER_DISPBKGND_GAMMA : 0) |
- (interlace ? SCALER_DISPBKGND_INTERLACE : 0));
-
- /* Reload the LUT, since the SRAMs would have been disabled if
- * all CRTCs had SCALER_DISPBKGND_GAMMA unset at once.
- */
- vc4_hvs_lut_load(crtc);
-}
-
void vc4_hvs_mask_underrun(struct drm_device *dev, int channel)
{
struct vc4_dev *vc4 = to_vc4_dev(dev);
diff --git a/drivers/gpu/drm/vc4/vc4_txp.c b/drivers/gpu/drm/vc4/vc4_txp.c
index a2380d856000..849dcafbfff1 100644
--- a/drivers/gpu/drm/vc4/vc4_txp.c
+++ b/drivers/gpu/drm/vc4/vc4_txp.c
@@ -436,7 +436,6 @@ static const struct drm_crtc_helper_funcs vc4_txp_crtc_helper_funcs = {
.atomic_flush = vc4_hvs_atomic_flush,
.atomic_enable = vc4_txp_atomic_enable,
.atomic_disable = vc4_txp_atomic_disable,
- .mode_set_nofb = vc4_hvs_mode_set_nofb,
};
static irqreturn_t vc4_txp_interrupt(int irq, void *data)
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 23/80] drm/vc4: crtc: Move the HVS gamma LUT setup to our init function
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Since most of the HVS channel is setup in the init function, let's move the
gamma setup there too. As this makes the HVS mode_set function empty, let's
remove it in the process.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
drivers/gpu/drm/vc4/vc4_drv.h | 1 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 59 +++++++++--------------------------
drivers/gpu/drm/vc4/vc4_txp.c | 1 +-
4 files changed, 16 insertions(+), 47 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 181d3fd57bc7..284a85b9d7d4 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -379,8 +379,6 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
{
vc4_crtc_config_pv(crtc);
-
- vc4_hvs_mode_set_nofb(crtc);
}
static void require_hvs_enabled(struct drm_device *dev)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 4126506b3a69..dfcc684f5d28 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -904,7 +904,6 @@ int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_crtc_state *state);
void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_flush(struct drm_crtc *crtc, struct drm_crtc_state *state);
-void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc);
void vc4_hvs_dump_state(struct drm_device *dev);
void vc4_hvs_unmask_underrun(struct drm_device *dev, int channel);
void vc4_hvs_mask_underrun(struct drm_device *dev, int channel);
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index dde931233d4a..efaae60bb323 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -201,6 +201,8 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
{
struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state);
unsigned int chan = vc4_crtc_state->assigned_channel;
+ bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
+ u32 dispbkgndx;
u32 dispctrl;
/* Turn on the scaler, which will wait for vstart to start
@@ -225,6 +227,20 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
HVS_WRITE(SCALER_DISPCTRLX(chan), dispctrl);
+ dispbkgndx = HVS_READ(SCALER_DISPBKGNDX(chan));
+ dispbkgndx &= ~SCALER_DISPBKGND_GAMMA;
+ dispbkgndx &= ~SCALER_DISPBKGND_INTERLACE;
+
+ HVS_WRITE(SCALER_DISPBKGNDX(chan), dispbkgndx |
+ SCALER_DISPBKGND_AUTOHS |
+ ((!vc4->hvs->hvs5) ? SCALER_DISPBKGND_GAMMA : 0) |
+ (interlace ? SCALER_DISPBKGND_INTERLACE : 0));
+
+ /* Reload the LUT, since the SRAMs would have been disabled if
+ * all CRTCs had SCALER_DISPBKGND_GAMMA unset at once.
+ */
+ vc4_hvs_lut_load(crtc);
+
return 0;
}
@@ -421,49 +437,6 @@ void vc4_hvs_atomic_flush(struct drm_crtc *crtc,
}
}
-void vc4_hvs_mode_set_nofb(struct drm_crtc *crtc)
-{
- struct drm_device *dev = crtc->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
- struct drm_display_mode *mode = &crtc->state->adjusted_mode;
- bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
-
- if (vc4_state->assigned_channel == 2) {
- u32 dispctrl;
- u32 dsp3_mux;
-
- /*
- * SCALER_DISPCTRL_DSP3 = X, where X < 2 means 'connect DSP3 to
- * FIFO X'.
- * SCALER_DISPCTRL_DSP3 = 3 means 'disable DSP 3'.
- *
- * DSP3 is connected to FIFO2 unless the transposer is
- * enabled. In this case, FIFO 2 is directly accessed by the
- * TXP IP, and we need to disable the FIFO2 -> pixelvalve1
- * route.
- */
- if (vc4_state->feed_txp)
- dsp3_mux = VC4_SET_FIELD(3, SCALER_DISPCTRL_DSP3_MUX);
- else
- dsp3_mux = VC4_SET_FIELD(2, SCALER_DISPCTRL_DSP3_MUX);
-
- dispctrl = HVS_READ(SCALER_DISPCTRL) &
- ~SCALER_DISPCTRL_DSP3_MUX_MASK;
- HVS_WRITE(SCALER_DISPCTRL, dispctrl | dsp3_mux);
- }
-
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_state->assigned_channel),
- SCALER_DISPBKGND_AUTOHS |
- ((!vc4->hvs->hvs5) ? SCALER_DISPBKGND_GAMMA : 0) |
- (interlace ? SCALER_DISPBKGND_INTERLACE : 0));
-
- /* Reload the LUT, since the SRAMs would have been disabled if
- * all CRTCs had SCALER_DISPBKGND_GAMMA unset at once.
- */
- vc4_hvs_lut_load(crtc);
-}
-
void vc4_hvs_mask_underrun(struct drm_device *dev, int channel)
{
struct vc4_dev *vc4 = to_vc4_dev(dev);
diff --git a/drivers/gpu/drm/vc4/vc4_txp.c b/drivers/gpu/drm/vc4/vc4_txp.c
index a2380d856000..849dcafbfff1 100644
--- a/drivers/gpu/drm/vc4/vc4_txp.c
+++ b/drivers/gpu/drm/vc4/vc4_txp.c
@@ -436,7 +436,6 @@ static const struct drm_crtc_helper_funcs vc4_txp_crtc_helper_funcs = {
.atomic_flush = vc4_hvs_atomic_flush,
.atomic_enable = vc4_txp_atomic_enable,
.atomic_disable = vc4_txp_atomic_disable,
- .mode_set_nofb = vc4_hvs_mode_set_nofb,
};
static irqreturn_t vc4_txp_interrupt(int irq, void *data)
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 24/80] drm/vc4: hvs: Make sure our channel is reset
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
In order to clear our intermediate FIFOs that might end up with a stale
pixel, let's make sure our FIFO channel is reset every time our channel is
setup.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hvs.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index efaae60bb323..0f56a7b57916 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -205,6 +205,10 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
u32 dispbkgndx;
u32 dispctrl;
+ HVS_WRITE(SCALER_DISPCTRLX(chan), 0);
+ HVS_WRITE(SCALER_DISPCTRLX(chan), SCALER_DISPCTRLX_RESET);
+ HVS_WRITE(SCALER_DISPCTRLX(chan), 0);
+
/* Turn on the scaler, which will wait for vstart to start
* compositing.
* When feeding the transposer, we should operate in oneshot
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 24/80] drm/vc4: hvs: Make sure our channel is reset
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to clear our intermediate FIFOs that might end up with a stale
pixel, let's make sure our FIFO channel is reset every time our channel is
setup.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hvs.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index efaae60bb323..0f56a7b57916 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -205,6 +205,10 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
u32 dispbkgndx;
u32 dispctrl;
+ HVS_WRITE(SCALER_DISPCTRLX(chan), 0);
+ HVS_WRITE(SCALER_DISPCTRLX(chan), SCALER_DISPCTRLX_RESET);
+ HVS_WRITE(SCALER_DISPCTRLX(chan), 0);
+
/* Turn on the scaler, which will wait for vstart to start
* compositing.
* When feeding the transposer, we should operate in oneshot
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 24/80] drm/vc4: hvs: Make sure our channel is reset
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to clear our intermediate FIFOs that might end up with a stale
pixel, let's make sure our FIFO channel is reset every time our channel is
setup.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hvs.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index efaae60bb323..0f56a7b57916 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -205,6 +205,10 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
u32 dispbkgndx;
u32 dispctrl;
+ HVS_WRITE(SCALER_DISPCTRLX(chan), 0);
+ HVS_WRITE(SCALER_DISPCTRLX(chan), SCALER_DISPCTRLX_RESET);
+ HVS_WRITE(SCALER_DISPCTRLX(chan), 0);
+
/* Turn on the scaler, which will wait for vstart to start
* compositing.
* When feeding the transposer, we should operate in oneshot
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 25/80] drm/vc4: crtc: Remove mode_set_nofb
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
On BCM2711 to avoid stale pixels getting stuck in intermediate FIFOs, the
pixelvalve needs to be setup each time there's a mode change or enable /
disable sequence.
Therefore, we can't really use mode_set_nofb anymore to configure it, but
we need to move it to atomic_enable.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 7 +------
1 file changed, 1 insertion(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 284a85b9d7d4..2eda2e6429ec 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -376,11 +376,6 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
}
}
-static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
-{
- vc4_crtc_config_pv(crtc);
-}
-
static void require_hvs_enabled(struct drm_device *dev)
{
struct vc4_dev *vc4 = to_vc4_dev(dev);
@@ -433,6 +428,7 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
vc4_crtc_pixelvalve_reset(crtc);
+ vc4_crtc_config_pv(crtc);
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
@@ -791,7 +787,6 @@ static const struct drm_crtc_funcs vc4_crtc_funcs = {
};
static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
- .mode_set_nofb = vc4_crtc_mode_set_nofb,
.mode_valid = vc4_crtc_mode_valid,
.atomic_check = vc4_crtc_atomic_check,
.atomic_flush = vc4_hvs_atomic_flush,
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 25/80] drm/vc4: crtc: Remove mode_set_nofb
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
On BCM2711 to avoid stale pixels getting stuck in intermediate FIFOs, the
pixelvalve needs to be setup each time there's a mode change or enable /
disable sequence.
Therefore, we can't really use mode_set_nofb anymore to configure it, but
we need to move it to atomic_enable.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 7 +------
1 file changed, 1 insertion(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 284a85b9d7d4..2eda2e6429ec 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -376,11 +376,6 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
}
}
-static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
-{
- vc4_crtc_config_pv(crtc);
-}
-
static void require_hvs_enabled(struct drm_device *dev)
{
struct vc4_dev *vc4 = to_vc4_dev(dev);
@@ -433,6 +428,7 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
vc4_crtc_pixelvalve_reset(crtc);
+ vc4_crtc_config_pv(crtc);
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
@@ -791,7 +787,6 @@ static const struct drm_crtc_funcs vc4_crtc_funcs = {
};
static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
- .mode_set_nofb = vc4_crtc_mode_set_nofb,
.mode_valid = vc4_crtc_mode_valid,
.atomic_check = vc4_crtc_atomic_check,
.atomic_flush = vc4_hvs_atomic_flush,
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 25/80] drm/vc4: crtc: Remove mode_set_nofb
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
On BCM2711 to avoid stale pixels getting stuck in intermediate FIFOs, the
pixelvalve needs to be setup each time there's a mode change or enable /
disable sequence.
Therefore, we can't really use mode_set_nofb anymore to configure it, but
we need to move it to atomic_enable.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 7 +------
1 file changed, 1 insertion(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 284a85b9d7d4..2eda2e6429ec 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -376,11 +376,6 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
}
}
-static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
-{
- vc4_crtc_config_pv(crtc);
-}
-
static void require_hvs_enabled(struct drm_device *dev)
{
struct vc4_dev *vc4 = to_vc4_dev(dev);
@@ -433,6 +428,7 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
vc4_crtc_pixelvalve_reset(crtc);
+ vc4_crtc_config_pv(crtc);
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
@@ -791,7 +787,6 @@ static const struct drm_crtc_funcs vc4_crtc_funcs = {
};
static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
- .mode_set_nofb = vc4_crtc_mode_set_nofb,
.mode_valid = vc4_crtc_mode_valid,
.atomic_check = vc4_crtc_atomic_check,
.atomic_flush = vc4_hvs_atomic_flush,
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 26/80] drm/vc4: crtc: Remove redundant pixelvalve reset
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Since we moved the pixelvalve configuration to atomic_enable, we're now
first calling the function that resets the pixelvalve and then the one that
configures it.
However, the first thing the latter is doing is calling the reset function,
meaning that we reset twice our pixelvalve. Let's remove the first call.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 1 -
1 file changed, 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 2eda2e6429ec..2c5ff45dc315 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -427,7 +427,6 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
- vc4_crtc_pixelvalve_reset(crtc);
vc4_crtc_config_pv(crtc);
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 26/80] drm/vc4: crtc: Remove redundant pixelvalve reset
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Since we moved the pixelvalve configuration to atomic_enable, we're now
first calling the function that resets the pixelvalve and then the one that
configures it.
However, the first thing the latter is doing is calling the reset function,
meaning that we reset twice our pixelvalve. Let's remove the first call.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 1 -
1 file changed, 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 2eda2e6429ec..2c5ff45dc315 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -427,7 +427,6 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
- vc4_crtc_pixelvalve_reset(crtc);
vc4_crtc_config_pv(crtc);
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 26/80] drm/vc4: crtc: Remove redundant pixelvalve reset
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Since we moved the pixelvalve configuration to atomic_enable, we're now
first calling the function that resets the pixelvalve and then the one that
configures it.
However, the first thing the latter is doing is calling the reset function,
meaning that we reset twice our pixelvalve. Let's remove the first call.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 1 -
1 file changed, 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 2eda2e6429ec..2c5ff45dc315 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -427,7 +427,6 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
- vc4_crtc_pixelvalve_reset(crtc);
vc4_crtc_config_pv(crtc);
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 27/80] drm/vc4: crtc: Move HVS channel init before the PV initialisation
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:00 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
In order to avoid stale pixels getting stuck in an intermediate FIFO
between the HVS and the pixelvalve on BCM2711, we need to configure the HVS
channel before the pixelvalve is reset and configured.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 2c5ff45dc315..b7b0e19e2fe1 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -427,10 +427,6 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
- vc4_crtc_config_pv(crtc);
-
- CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
-
/* Enable vblank irq handling before crtc is started otherwise
* drm_crtc_get_vblank() fails in vc4_crtc_update_dlist().
*/
@@ -438,6 +434,10 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
vc4_hvs_atomic_enable(crtc, old_state);
+ vc4_crtc_config_pv(crtc);
+
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
+
/* When feeding the transposer block the pixelvalve is unneeded and
* should not be enabled.
*/
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 27/80] drm/vc4: crtc: Move HVS channel init before the PV initialisation
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to avoid stale pixels getting stuck in an intermediate FIFO
between the HVS and the pixelvalve on BCM2711, we need to configure the HVS
channel before the pixelvalve is reset and configured.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 2c5ff45dc315..b7b0e19e2fe1 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -427,10 +427,6 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
- vc4_crtc_config_pv(crtc);
-
- CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
-
/* Enable vblank irq handling before crtc is started otherwise
* drm_crtc_get_vblank() fails in vc4_crtc_update_dlist().
*/
@@ -438,6 +434,10 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
vc4_hvs_atomic_enable(crtc, old_state);
+ vc4_crtc_config_pv(crtc);
+
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
+
/* When feeding the transposer block the pixelvalve is unneeded and
* should not be enabled.
*/
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 27/80] drm/vc4: crtc: Move HVS channel init before the PV initialisation
@ 2020-09-03 8:00 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:00 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to avoid stale pixels getting stuck in an intermediate FIFO
between the HVS and the pixelvalve on BCM2711, we need to configure the HVS
channel before the pixelvalve is reset and configured.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 2c5ff45dc315..b7b0e19e2fe1 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -427,10 +427,6 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
require_hvs_enabled(dev);
- vc4_crtc_config_pv(crtc);
-
- CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
-
/* Enable vblank irq handling before crtc is started otherwise
* drm_crtc_get_vblank() fails in vc4_crtc_update_dlist().
*/
@@ -438,6 +434,10 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
vc4_hvs_atomic_enable(crtc, old_state);
+ vc4_crtc_config_pv(crtc);
+
+ CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
+
/* When feeding the transposer block the pixelvalve is unneeded and
* should not be enabled.
*/
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 28/80] drm/vc4: encoder: Add finer-grained encoder callbacks
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
In the BCM2711, the setup of the HVS, pixelvalve and HDMI controller
requires very precise ordering and timing that the regular atomic callbacks
don't provide. Let's add new callbacks on top of the regular ones to be
able to split the configuration as needed.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 19 +++++++++++++++++++
drivers/gpu/drm/vc4/vc4_drv.h | 7 +++++++
2 files changed, 26 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index b7b0e19e2fe1..d0b326e1df0a 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -389,6 +389,8 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
+ struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
int ret;
require_hvs_enabled(dev);
@@ -401,10 +403,16 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n");
+ if (vc4_encoder->post_crtc_disable)
+ vc4_encoder->post_crtc_disable(encoder);
+
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
vc4_hvs_atomic_disable(crtc, old_state);
+ if (vc4_encoder->post_crtc_powerdown)
+ vc4_encoder->post_crtc_powerdown(encoder);
+
/*
* Make sure we issue a vblank event after disabling the CRTC if
* someone was waiting it.
@@ -424,6 +432,8 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
+ struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
require_hvs_enabled(dev);
@@ -434,15 +444,24 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
vc4_hvs_atomic_enable(crtc, old_state);
+ if (vc4_encoder->pre_crtc_configure)
+ vc4_encoder->pre_crtc_configure(encoder);
+
vc4_crtc_config_pv(crtc);
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
+ if (vc4_encoder->pre_crtc_enable)
+ vc4_encoder->pre_crtc_enable(encoder);
+
/* When feeding the transposer block the pixelvalve is unneeded and
* should not be enabled.
*/
CRTC_WRITE(PV_V_CONTROL,
CRTC_READ(PV_V_CONTROL) | PV_VCONTROL_VIDEN);
+
+ if (vc4_encoder->post_crtc_enable)
+ vc4_encoder->post_crtc_enable(encoder);
}
static enum drm_mode_status vc4_crtc_mode_valid(struct drm_crtc *crtc,
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index dfcc684f5d28..251fcc35530c 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -439,6 +439,13 @@ struct vc4_encoder {
struct drm_encoder base;
enum vc4_encoder_type type;
u32 clock_select;
+
+ void (*pre_crtc_configure)(struct drm_encoder *encoder);
+ void (*pre_crtc_enable)(struct drm_encoder *encoder);
+ void (*post_crtc_enable)(struct drm_encoder *encoder);
+
+ void (*post_crtc_disable)(struct drm_encoder *encoder);
+ void (*post_crtc_powerdown)(struct drm_encoder *encoder);
};
static inline struct vc4_encoder *
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 28/80] drm/vc4: encoder: Add finer-grained encoder callbacks
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In the BCM2711, the setup of the HVS, pixelvalve and HDMI controller
requires very precise ordering and timing that the regular atomic callbacks
don't provide. Let's add new callbacks on top of the regular ones to be
able to split the configuration as needed.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 19 +++++++++++++++++++
drivers/gpu/drm/vc4/vc4_drv.h | 7 +++++++
2 files changed, 26 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index b7b0e19e2fe1..d0b326e1df0a 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -389,6 +389,8 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
+ struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
int ret;
require_hvs_enabled(dev);
@@ -401,10 +403,16 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n");
+ if (vc4_encoder->post_crtc_disable)
+ vc4_encoder->post_crtc_disable(encoder);
+
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
vc4_hvs_atomic_disable(crtc, old_state);
+ if (vc4_encoder->post_crtc_powerdown)
+ vc4_encoder->post_crtc_powerdown(encoder);
+
/*
* Make sure we issue a vblank event after disabling the CRTC if
* someone was waiting it.
@@ -424,6 +432,8 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
+ struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
require_hvs_enabled(dev);
@@ -434,15 +444,24 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
vc4_hvs_atomic_enable(crtc, old_state);
+ if (vc4_encoder->pre_crtc_configure)
+ vc4_encoder->pre_crtc_configure(encoder);
+
vc4_crtc_config_pv(crtc);
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
+ if (vc4_encoder->pre_crtc_enable)
+ vc4_encoder->pre_crtc_enable(encoder);
+
/* When feeding the transposer block the pixelvalve is unneeded and
* should not be enabled.
*/
CRTC_WRITE(PV_V_CONTROL,
CRTC_READ(PV_V_CONTROL) | PV_VCONTROL_VIDEN);
+
+ if (vc4_encoder->post_crtc_enable)
+ vc4_encoder->post_crtc_enable(encoder);
}
static enum drm_mode_status vc4_crtc_mode_valid(struct drm_crtc *crtc,
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index dfcc684f5d28..251fcc35530c 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -439,6 +439,13 @@ struct vc4_encoder {
struct drm_encoder base;
enum vc4_encoder_type type;
u32 clock_select;
+
+ void (*pre_crtc_configure)(struct drm_encoder *encoder);
+ void (*pre_crtc_enable)(struct drm_encoder *encoder);
+ void (*post_crtc_enable)(struct drm_encoder *encoder);
+
+ void (*post_crtc_disable)(struct drm_encoder *encoder);
+ void (*post_crtc_powerdown)(struct drm_encoder *encoder);
};
static inline struct vc4_encoder *
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 28/80] drm/vc4: encoder: Add finer-grained encoder callbacks
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In the BCM2711, the setup of the HVS, pixelvalve and HDMI controller
requires very precise ordering and timing that the regular atomic callbacks
don't provide. Let's add new callbacks on top of the regular ones to be
able to split the configuration as needed.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 19 +++++++++++++++++++
drivers/gpu/drm/vc4/vc4_drv.h | 7 +++++++
2 files changed, 26 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index b7b0e19e2fe1..d0b326e1df0a 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -389,6 +389,8 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
+ struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
int ret;
require_hvs_enabled(dev);
@@ -401,10 +403,16 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n");
+ if (vc4_encoder->post_crtc_disable)
+ vc4_encoder->post_crtc_disable(encoder);
+
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
vc4_hvs_atomic_disable(crtc, old_state);
+ if (vc4_encoder->post_crtc_powerdown)
+ vc4_encoder->post_crtc_powerdown(encoder);
+
/*
* Make sure we issue a vblank event after disabling the CRTC if
* someone was waiting it.
@@ -424,6 +432,8 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
{
struct drm_device *dev = crtc->dev;
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
+ struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
require_hvs_enabled(dev);
@@ -434,15 +444,24 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,
vc4_hvs_atomic_enable(crtc, old_state);
+ if (vc4_encoder->pre_crtc_configure)
+ vc4_encoder->pre_crtc_configure(encoder);
+
vc4_crtc_config_pv(crtc);
CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN);
+ if (vc4_encoder->pre_crtc_enable)
+ vc4_encoder->pre_crtc_enable(encoder);
+
/* When feeding the transposer block the pixelvalve is unneeded and
* should not be enabled.
*/
CRTC_WRITE(PV_V_CONTROL,
CRTC_READ(PV_V_CONTROL) | PV_VCONTROL_VIDEN);
+
+ if (vc4_encoder->post_crtc_enable)
+ vc4_encoder->post_crtc_enable(encoder);
}
static enum drm_mode_status vc4_crtc_mode_valid(struct drm_crtc *crtc,
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index dfcc684f5d28..251fcc35530c 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -439,6 +439,13 @@ struct vc4_encoder {
struct drm_encoder base;
enum vc4_encoder_type type;
u32 clock_select;
+
+ void (*pre_crtc_configure)(struct drm_encoder *encoder);
+ void (*pre_crtc_enable)(struct drm_encoder *encoder);
+ void (*post_crtc_enable)(struct drm_encoder *encoder);
+
+ void (*post_crtc_disable)(struct drm_encoder *encoder);
+ void (*post_crtc_powerdown)(struct drm_encoder *encoder);
};
static inline struct vc4_encoder *
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 29/80] drm/vc4: crtc: Add a delay after disabling the PixelValve output
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
In order to avoid pixels getting stuck in the (unflushable) FIFO between
the HVS and the PV, we need to add some delay after disabling the PV output
and before disabling the HDMI controller. 20ms seems to be good enough so
let's use that.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index d0b326e1df0a..4c23cf8aefb9 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -403,6 +403,24 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n");
+ /*
+ * This delay is needed to avoid to get a pixel stuck in an
+ * unflushable FIFO between the pixelvalve and the HDMI
+ * controllers on the BCM2711.
+ *
+ * Timing is fairly sensitive here, so mdelay is the safest
+ * approach.
+ *
+ * If it was to be reworked, the stuck pixel happens on a
+ * BCM2711 when changing mode with a good probability, so a
+ * script that changes mode on a regular basis should trigger
+ * the bug after less than 10 attempts. It manifests itself with
+ * every pixels being shifted by one to the right, and thus the
+ * last pixel of a line actually being displayed as the first
+ * pixel on the next line.
+ */
+ mdelay(20);
+
if (vc4_encoder->post_crtc_disable)
vc4_encoder->post_crtc_disable(encoder);
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 29/80] drm/vc4: crtc: Add a delay after disabling the PixelValve output
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to avoid pixels getting stuck in the (unflushable) FIFO between
the HVS and the PV, we need to add some delay after disabling the PV output
and before disabling the HDMI controller. 20ms seems to be good enough so
let's use that.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index d0b326e1df0a..4c23cf8aefb9 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -403,6 +403,24 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n");
+ /*
+ * This delay is needed to avoid to get a pixel stuck in an
+ * unflushable FIFO between the pixelvalve and the HDMI
+ * controllers on the BCM2711.
+ *
+ * Timing is fairly sensitive here, so mdelay is the safest
+ * approach.
+ *
+ * If it was to be reworked, the stuck pixel happens on a
+ * BCM2711 when changing mode with a good probability, so a
+ * script that changes mode on a regular basis should trigger
+ * the bug after less than 10 attempts. It manifests itself with
+ * every pixels being shifted by one to the right, and thus the
+ * last pixel of a line actually being displayed as the first
+ * pixel on the next line.
+ */
+ mdelay(20);
+
if (vc4_encoder->post_crtc_disable)
vc4_encoder->post_crtc_disable(encoder);
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 29/80] drm/vc4: crtc: Add a delay after disabling the PixelValve output
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to avoid pixels getting stuck in the (unflushable) FIFO between
the HVS and the PV, we need to add some delay after disabling the PV output
and before disabling the HDMI controller. 20ms seems to be good enough so
let's use that.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index d0b326e1df0a..4c23cf8aefb9 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -403,6 +403,24 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n");
+ /*
+ * This delay is needed to avoid to get a pixel stuck in an
+ * unflushable FIFO between the pixelvalve and the HDMI
+ * controllers on the BCM2711.
+ *
+ * Timing is fairly sensitive here, so mdelay is the safest
+ * approach.
+ *
+ * If it was to be reworked, the stuck pixel happens on a
+ * BCM2711 when changing mode with a good probability, so a
+ * script that changes mode on a regular basis should trigger
+ * the bug after less than 10 attempts. It manifests itself with
+ * every pixels being shifted by one to the right, and thus the
+ * last pixel of a line actually being displayed as the first
+ * pixel on the next line.
+ */
+ mdelay(20);
+
if (vc4_encoder->post_crtc_disable)
vc4_encoder->post_crtc_disable(encoder);
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 30/80] drm/vc4: crtc: Clear the PixelValve FIFO on disable
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
In order to avoid a stale pixel getting stuck on mode change or a disable
/ enable cycle, we need to make sure to flush the PV FIFO on disable.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 4c23cf8aefb9..73d918706f7e 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -424,8 +424,7 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
if (vc4_encoder->post_crtc_disable)
vc4_encoder->post_crtc_disable(encoder);
- CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
-
+ vc4_crtc_pixelvalve_reset(crtc);
vc4_hvs_atomic_disable(crtc, old_state);
if (vc4_encoder->post_crtc_powerdown)
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 30/80] drm/vc4: crtc: Clear the PixelValve FIFO on disable
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to avoid a stale pixel getting stuck on mode change or a disable
/ enable cycle, we need to make sure to flush the PV FIFO on disable.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 4c23cf8aefb9..73d918706f7e 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -424,8 +424,7 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
if (vc4_encoder->post_crtc_disable)
vc4_encoder->post_crtc_disable(encoder);
- CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
-
+ vc4_crtc_pixelvalve_reset(crtc);
vc4_hvs_atomic_disable(crtc, old_state);
if (vc4_encoder->post_crtc_powerdown)
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 30/80] drm/vc4: crtc: Clear the PixelValve FIFO on disable
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to avoid a stale pixel getting stuck on mode change or a disable
/ enable cycle, we need to make sure to flush the PV FIFO on disable.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 4c23cf8aefb9..73d918706f7e 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -424,8 +424,7 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
if (vc4_encoder->post_crtc_disable)
vc4_encoder->post_crtc_disable(encoder);
- CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN);
-
+ vc4_crtc_pixelvalve_reset(crtc);
vc4_hvs_atomic_disable(crtc, old_state);
if (vc4_encoder->post_crtc_powerdown)
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 31/80] drm/vc4: crtc: Clear the PixelValve FIFO during configuration
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Even though it's not really clear why we need to flush the PV FIFO during
the configuration even though we started by flushing it, experience shows
that without it we get a stale pixel stuck in the FIFO between the HVS and
the PV.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 73d918706f7e..00b2c2b011d1 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -358,7 +358,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
if (is_dsi)
CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
- CRTC_WRITE(PV_CONTROL,
+ CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR |
vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) |
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 31/80] drm/vc4: crtc: Clear the PixelValve FIFO during configuration
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Even though it's not really clear why we need to flush the PV FIFO during
the configuration even though we started by flushing it, experience shows
that without it we get a stale pixel stuck in the FIFO between the HVS and
the PV.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 73d918706f7e..00b2c2b011d1 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -358,7 +358,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
if (is_dsi)
CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
- CRTC_WRITE(PV_CONTROL,
+ CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR |
vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) |
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 31/80] drm/vc4: crtc: Clear the PixelValve FIFO during configuration
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Even though it's not really clear why we need to flush the PV FIFO during
the configuration even though we started by flushing it, experience shows
that without it we get a stale pixel stuck in the FIFO between the HVS and
the PV.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 73d918706f7e..00b2c2b011d1 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -358,7 +358,7 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
if (is_dsi)
CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
- CRTC_WRITE(PV_CONTROL,
+ CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR |
vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) |
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 32/80] drm/vc4: hvs: Make the stop_channel function public
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
During the transition from the firmware to the KMS driver, we need to pay
particular attention to how we deal with the pixelvalves that have already
been enabled, otherwise either timeouts or stuck pixels can occur. We'll
thus need to call the function to stop an HVS channel at boot.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 1 +
drivers/gpu/drm/vc4/vc4_hvs.c | 2 +-
2 files changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 251fcc35530c..554c2e29b23d 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -907,6 +907,7 @@ void vc4_irq_reset(struct drm_device *dev);
/* vc4_hvs.c */
extern struct platform_driver vc4_hvs_driver;
+void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int output);
int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_crtc_state *state);
void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 0f56a7b57916..b5ee9556e821 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -248,7 +248,7 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
return 0;
}
-static void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int chan)
+void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int chan)
{
struct vc4_dev *vc4 = to_vc4_dev(dev);
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 32/80] drm/vc4: hvs: Make the stop_channel function public
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
During the transition from the firmware to the KMS driver, we need to pay
particular attention to how we deal with the pixelvalves that have already
been enabled, otherwise either timeouts or stuck pixels can occur. We'll
thus need to call the function to stop an HVS channel at boot.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 1 +
drivers/gpu/drm/vc4/vc4_hvs.c | 2 +-
2 files changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 251fcc35530c..554c2e29b23d 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -907,6 +907,7 @@ void vc4_irq_reset(struct drm_device *dev);
/* vc4_hvs.c */
extern struct platform_driver vc4_hvs_driver;
+void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int output);
int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_crtc_state *state);
void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 0f56a7b57916..b5ee9556e821 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -248,7 +248,7 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
return 0;
}
-static void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int chan)
+void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int chan)
{
struct vc4_dev *vc4 = to_vc4_dev(dev);
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 32/80] drm/vc4: hvs: Make the stop_channel function public
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
During the transition from the firmware to the KMS driver, we need to pay
particular attention to how we deal with the pixelvalves that have already
been enabled, otherwise either timeouts or stuck pixels can occur. We'll
thus need to call the function to stop an HVS channel at boot.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 1 +
drivers/gpu/drm/vc4/vc4_hvs.c | 2 +-
2 files changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 251fcc35530c..554c2e29b23d 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -907,6 +907,7 @@ void vc4_irq_reset(struct drm_device *dev);
/* vc4_hvs.c */
extern struct platform_driver vc4_hvs_driver;
+void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int output);
int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_crtc_state *state);
void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index 0f56a7b57916..b5ee9556e821 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -248,7 +248,7 @@ static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
return 0;
}
-static void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int chan)
+void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int chan)
{
struct vc4_dev *vc4 = to_vc4_dev(dev);
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 33/80] drm/vc4: hvs: Introduce a function to get the assigned FIFO
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
At boot time, if we detect that a pixelvalve has been enabled, we need to
be able to retrieve the HVS channel it has been assigned to so that we can
disable that channel too. Let's create that function that returns the FIFO
or an error from a given output.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 1 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 54 ++++++++++++++++++++++++++++++++++++-
2 files changed, 55 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 554c2e29b23d..860be019d8e3 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -908,6 +908,7 @@ void vc4_irq_reset(struct drm_device *dev);
/* vc4_hvs.c */
extern struct platform_driver vc4_hvs_driver;
void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int output);
+int vc4_hvs_get_fifo_from_output(struct drm_device *dev, unsigned int output);
int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_crtc_state *state);
void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index b5ee9556e821..4d0a833366ce 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -19,6 +19,7 @@
* each CRTC.
*/
+#include <linux/bitfield.h>
#include <linux/clk.h>
#include <linux/component.h>
#include <linux/platform_device.h>
@@ -196,6 +197,59 @@ static void vc4_hvs_update_gamma_lut(struct drm_crtc *crtc)
vc4_hvs_lut_load(crtc);
}
+int vc4_hvs_get_fifo_from_output(struct drm_device *dev, unsigned int output)
+{
+ struct vc4_dev *vc4 = to_vc4_dev(dev);
+ u32 reg;
+ int ret;
+
+ if (!vc4->hvs->hvs5)
+ return output;
+
+ switch (output) {
+ case 0:
+ return 0;
+
+ case 1:
+ return 1;
+
+ case 2:
+ reg = HVS_READ(SCALER_DISPECTRL);
+ ret = FIELD_GET(SCALER_DISPECTRL_DSP2_MUX_MASK, reg);
+ if (ret == 0)
+ return 2;
+
+ return 0;
+
+ case 3:
+ reg = HVS_READ(SCALER_DISPCTRL);
+ ret = FIELD_GET(SCALER_DISPCTRL_DSP3_MUX_MASK, reg);
+ if (ret == 3)
+ return -EPIPE;
+
+ return ret;
+
+ case 4:
+ reg = HVS_READ(SCALER_DISPEOLN);
+ ret = FIELD_GET(SCALER_DISPEOLN_DSP4_MUX_MASK, reg);
+ if (ret == 3)
+ return -EPIPE;
+
+ return ret;
+
+ case 5:
+ reg = HVS_READ(SCALER_DISPDITHER);
+ ret = FIELD_GET(SCALER_DISPDITHER_DSP5_MUX_MASK, reg);
+ if (ret == 3)
+ return -EPIPE;
+
+ return ret;
+
+ default:
+ return -EPIPE;
+ }
+}
+
static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
struct drm_display_mode *mode, bool oneshot)
{
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 33/80] drm/vc4: hvs: Introduce a function to get the assigned FIFO
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
At boot time, if we detect that a pixelvalve has been enabled, we need to
be able to retrieve the HVS channel it has been assigned to so that we can
disable that channel too. Let's create that function that returns the FIFO
or an error from a given output.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 1 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 54 ++++++++++++++++++++++++++++++++++++-
2 files changed, 55 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 554c2e29b23d..860be019d8e3 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -908,6 +908,7 @@ void vc4_irq_reset(struct drm_device *dev);
/* vc4_hvs.c */
extern struct platform_driver vc4_hvs_driver;
void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int output);
+int vc4_hvs_get_fifo_from_output(struct drm_device *dev, unsigned int output);
int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_crtc_state *state);
void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index b5ee9556e821..4d0a833366ce 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -19,6 +19,7 @@
* each CRTC.
*/
+#include <linux/bitfield.h>
#include <linux/clk.h>
#include <linux/component.h>
#include <linux/platform_device.h>
@@ -196,6 +197,59 @@ static void vc4_hvs_update_gamma_lut(struct drm_crtc *crtc)
vc4_hvs_lut_load(crtc);
}
+int vc4_hvs_get_fifo_from_output(struct drm_device *dev, unsigned int output)
+{
+ struct vc4_dev *vc4 = to_vc4_dev(dev);
+ u32 reg;
+ int ret;
+
+ if (!vc4->hvs->hvs5)
+ return output;
+
+ switch (output) {
+ case 0:
+ return 0;
+
+ case 1:
+ return 1;
+
+ case 2:
+ reg = HVS_READ(SCALER_DISPECTRL);
+ ret = FIELD_GET(SCALER_DISPECTRL_DSP2_MUX_MASK, reg);
+ if (ret == 0)
+ return 2;
+
+ return 0;
+
+ case 3:
+ reg = HVS_READ(SCALER_DISPCTRL);
+ ret = FIELD_GET(SCALER_DISPCTRL_DSP3_MUX_MASK, reg);
+ if (ret == 3)
+ return -EPIPE;
+
+ return ret;
+
+ case 4:
+ reg = HVS_READ(SCALER_DISPEOLN);
+ ret = FIELD_GET(SCALER_DISPEOLN_DSP4_MUX_MASK, reg);
+ if (ret == 3)
+ return -EPIPE;
+
+ return ret;
+
+ case 5:
+ reg = HVS_READ(SCALER_DISPDITHER);
+ ret = FIELD_GET(SCALER_DISPDITHER_DSP5_MUX_MASK, reg);
+ if (ret == 3)
+ return -EPIPE;
+
+ return ret;
+
+ default:
+ return -EPIPE;
+ }
+}
+
static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
struct drm_display_mode *mode, bool oneshot)
{
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 33/80] drm/vc4: hvs: Introduce a function to get the assigned FIFO
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
At boot time, if we detect that a pixelvalve has been enabled, we need to
be able to retrieve the HVS channel it has been assigned to so that we can
disable that channel too. Let's create that function that returns the FIFO
or an error from a given output.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_drv.h | 1 +-
drivers/gpu/drm/vc4/vc4_hvs.c | 54 ++++++++++++++++++++++++++++++++++++-
2 files changed, 55 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 554c2e29b23d..860be019d8e3 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -908,6 +908,7 @@ void vc4_irq_reset(struct drm_device *dev);
/* vc4_hvs.c */
extern struct platform_driver vc4_hvs_driver;
void vc4_hvs_stop_channel(struct drm_device *dev, unsigned int output);
+int vc4_hvs_get_fifo_from_output(struct drm_device *dev, unsigned int output);
int vc4_hvs_atomic_check(struct drm_crtc *crtc, struct drm_crtc_state *state);
void vc4_hvs_atomic_enable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
void vc4_hvs_atomic_disable(struct drm_crtc *crtc, struct drm_crtc_state *old_state);
diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c
index b5ee9556e821..4d0a833366ce 100644
--- a/drivers/gpu/drm/vc4/vc4_hvs.c
+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
@@ -19,6 +19,7 @@
* each CRTC.
*/
+#include <linux/bitfield.h>
#include <linux/clk.h>
#include <linux/component.h>
#include <linux/platform_device.h>
@@ -196,6 +197,59 @@ static void vc4_hvs_update_gamma_lut(struct drm_crtc *crtc)
vc4_hvs_lut_load(crtc);
}
+int vc4_hvs_get_fifo_from_output(struct drm_device *dev, unsigned int output)
+{
+ struct vc4_dev *vc4 = to_vc4_dev(dev);
+ u32 reg;
+ int ret;
+
+ if (!vc4->hvs->hvs5)
+ return output;
+
+ switch (output) {
+ case 0:
+ return 0;
+
+ case 1:
+ return 1;
+
+ case 2:
+ reg = HVS_READ(SCALER_DISPECTRL);
+ ret = FIELD_GET(SCALER_DISPECTRL_DSP2_MUX_MASK, reg);
+ if (ret == 0)
+ return 2;
+
+ return 0;
+
+ case 3:
+ reg = HVS_READ(SCALER_DISPCTRL);
+ ret = FIELD_GET(SCALER_DISPCTRL_DSP3_MUX_MASK, reg);
+ if (ret == 3)
+ return -EPIPE;
+
+ return ret;
+
+ case 4:
+ reg = HVS_READ(SCALER_DISPEOLN);
+ ret = FIELD_GET(SCALER_DISPEOLN_DSP4_MUX_MASK, reg);
+ if (ret == 3)
+ return -EPIPE;
+
+ return ret;
+
+ case 5:
+ reg = HVS_READ(SCALER_DISPDITHER);
+ ret = FIELD_GET(SCALER_DISPDITHER_DSP5_MUX_MASK, reg);
+ if (ret == 3)
+ return -EPIPE;
+
+ return ret;
+
+ default:
+ return -EPIPE;
+ }
+}
+
static int vc4_hvs_init_channel(struct vc4_dev *vc4, struct drm_crtc *crtc,
struct drm_display_mode *mode, bool oneshot)
{
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 34/80] drm/vc4: crtc: Move the CRTC disable out
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
We'll need to reuse the part that disables the HVS and PixelValve during
boot too, so let's create a separate function.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 34 ++++++++++++++++++++++------------
1 file changed, 22 insertions(+), 12 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 00b2c2b011d1..4156c5f66877 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -384,20 +384,14 @@ static void require_hvs_enabled(struct drm_device *dev)
SCALER_DISPCTRL_ENABLE);
}
-static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
- struct drm_crtc_state *old_state)
+static int vc4_crtc_disable(struct drm_crtc *crtc, unsigned int channel)
{
- struct drm_device *dev = crtc->dev;
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct drm_device *dev = crtc->dev;
int ret;
- require_hvs_enabled(dev);
-
- /* Disable vblank irq handling before crtc is disabled. */
- drm_crtc_vblank_off(crtc);
-
CRTC_WRITE(PV_V_CONTROL,
CRTC_READ(PV_V_CONTROL) & ~PV_VCONTROL_VIDEN);
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
@@ -421,15 +415,31 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
*/
mdelay(20);
- if (vc4_encoder->post_crtc_disable)
+ if (vc4_encoder && vc4_encoder->post_crtc_disable)
vc4_encoder->post_crtc_disable(encoder);
vc4_crtc_pixelvalve_reset(crtc);
- vc4_hvs_atomic_disable(crtc, old_state);
+ vc4_hvs_stop_channel(dev, channel);
- if (vc4_encoder->post_crtc_powerdown)
+ if (vc4_encoder && vc4_encoder->post_crtc_powerdown)
vc4_encoder->post_crtc_powerdown(encoder);
+ return 0;
+}
+
+static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_state)
+{
+ struct vc4_crtc_state *old_vc4_state = to_vc4_crtc_state(old_state);
+ struct drm_device *dev = crtc->dev;
+
+ require_hvs_enabled(dev);
+
+ /* Disable vblank irq handling before crtc is disabled. */
+ drm_crtc_vblank_off(crtc);
+
+ vc4_crtc_disable(crtc, old_vc4_state->assigned_channel);
+
/*
* Make sure we issue a vblank event after disabling the CRTC if
* someone was waiting it.
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 34/80] drm/vc4: crtc: Move the CRTC disable out
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
We'll need to reuse the part that disables the HVS and PixelValve during
boot too, so let's create a separate function.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 34 ++++++++++++++++++++++------------
1 file changed, 22 insertions(+), 12 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 00b2c2b011d1..4156c5f66877 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -384,20 +384,14 @@ static void require_hvs_enabled(struct drm_device *dev)
SCALER_DISPCTRL_ENABLE);
}
-static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
- struct drm_crtc_state *old_state)
+static int vc4_crtc_disable(struct drm_crtc *crtc, unsigned int channel)
{
- struct drm_device *dev = crtc->dev;
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct drm_device *dev = crtc->dev;
int ret;
- require_hvs_enabled(dev);
-
- /* Disable vblank irq handling before crtc is disabled. */
- drm_crtc_vblank_off(crtc);
-
CRTC_WRITE(PV_V_CONTROL,
CRTC_READ(PV_V_CONTROL) & ~PV_VCONTROL_VIDEN);
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
@@ -421,15 +415,31 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
*/
mdelay(20);
- if (vc4_encoder->post_crtc_disable)
+ if (vc4_encoder && vc4_encoder->post_crtc_disable)
vc4_encoder->post_crtc_disable(encoder);
vc4_crtc_pixelvalve_reset(crtc);
- vc4_hvs_atomic_disable(crtc, old_state);
+ vc4_hvs_stop_channel(dev, channel);
- if (vc4_encoder->post_crtc_powerdown)
+ if (vc4_encoder && vc4_encoder->post_crtc_powerdown)
vc4_encoder->post_crtc_powerdown(encoder);
+ return 0;
+}
+
+static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_state)
+{
+ struct vc4_crtc_state *old_vc4_state = to_vc4_crtc_state(old_state);
+ struct drm_device *dev = crtc->dev;
+
+ require_hvs_enabled(dev);
+
+ /* Disable vblank irq handling before crtc is disabled. */
+ drm_crtc_vblank_off(crtc);
+
+ vc4_crtc_disable(crtc, old_vc4_state->assigned_channel);
+
/*
* Make sure we issue a vblank event after disabling the CRTC if
* someone was waiting it.
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 34/80] drm/vc4: crtc: Move the CRTC disable out
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
We'll need to reuse the part that disables the HVS and PixelValve during
boot too, so let's create a separate function.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 34 ++++++++++++++++++++++------------
1 file changed, 22 insertions(+), 12 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 00b2c2b011d1..4156c5f66877 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -384,20 +384,14 @@ static void require_hvs_enabled(struct drm_device *dev)
SCALER_DISPCTRL_ENABLE);
}
-static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
- struct drm_crtc_state *old_state)
+static int vc4_crtc_disable(struct drm_crtc *crtc, unsigned int channel)
{
- struct drm_device *dev = crtc->dev;
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ struct drm_device *dev = crtc->dev;
int ret;
- require_hvs_enabled(dev);
-
- /* Disable vblank irq handling before crtc is disabled. */
- drm_crtc_vblank_off(crtc);
-
CRTC_WRITE(PV_V_CONTROL,
CRTC_READ(PV_V_CONTROL) & ~PV_VCONTROL_VIDEN);
ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
@@ -421,15 +415,31 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
*/
mdelay(20);
- if (vc4_encoder->post_crtc_disable)
+ if (vc4_encoder && vc4_encoder->post_crtc_disable)
vc4_encoder->post_crtc_disable(encoder);
vc4_crtc_pixelvalve_reset(crtc);
- vc4_hvs_atomic_disable(crtc, old_state);
+ vc4_hvs_stop_channel(dev, channel);
- if (vc4_encoder->post_crtc_powerdown)
+ if (vc4_encoder && vc4_encoder->post_crtc_powerdown)
vc4_encoder->post_crtc_powerdown(encoder);
+ return 0;
+}
+
+static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_state)
+{
+ struct vc4_crtc_state *old_vc4_state = to_vc4_crtc_state(old_state);
+ struct drm_device *dev = crtc->dev;
+
+ require_hvs_enabled(dev);
+
+ /* Disable vblank irq handling before crtc is disabled. */
+ drm_crtc_vblank_off(crtc);
+
+ vc4_crtc_disable(crtc, old_vc4_state->assigned_channel);
+
/*
* Make sure we issue a vblank event after disabling the CRTC if
* someone was waiting it.
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 35/80] drm/vc4: drv: Disable the CRTC at boot time
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
In order to prevent issues during the firmware to KMS transition, we need
to make sure the pixelvalve are disabled at boot time so that the DRM state
matches the hardware state.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 25 +++++++++++++++++++++++++
drivers/gpu/drm/vc4/vc4_drv.c | 4 ++++
drivers/gpu/drm/vc4/vc4_drv.h | 1 +
3 files changed, 30 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 4156c5f66877..dfac304fe2b0 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -427,6 +427,31 @@ static int vc4_crtc_disable(struct drm_crtc *crtc, unsigned int channel)
return 0;
}
+int vc4_crtc_disable_at_boot(struct drm_crtc *crtc)
+{
+ struct drm_device *drm = crtc->dev;
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ int channel;
+
+ if (!(of_device_is_compatible(vc4_crtc->pdev->dev.of_node,
+ "brcm,bcm2711-pixelvalve2") ||
+ of_device_is_compatible(vc4_crtc->pdev->dev.of_node,
+ "brcm,bcm2711-pixelvalve4")))
+ return 0;
+
+ if (!(CRTC_READ(PV_CONTROL) & PV_CONTROL_EN))
+ return 0;
+
+ if (!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN))
+ return 0;
+
+ channel = vc4_hvs_get_fifo_from_output(drm, vc4_crtc->data->hvs_output);
+ if (channel < 0)
+ return 0;
+
+ return vc4_crtc_disable(crtc, channel);
+}
+
static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
struct drm_crtc_state *old_state)
{
diff --git a/drivers/gpu/drm/vc4/vc4_drv.c b/drivers/gpu/drm/vc4/vc4_drv.c
index 38343d2fb4fb..9567d1019212 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.c
+++ b/drivers/gpu/drm/vc4/vc4_drv.c
@@ -252,6 +252,7 @@ static int vc4_drm_bind(struct device *dev)
struct drm_device *drm;
struct vc4_dev *vc4;
struct device_node *node;
+ struct drm_crtc *crtc;
int ret = 0;
dev->coherent_dma_mask = DMA_BIT_MASK(32);
@@ -298,6 +299,9 @@ static int vc4_drm_bind(struct device *dev)
if (ret < 0)
goto unbind_all;
+ drm_for_each_crtc(crtc, drm)
+ vc4_crtc_disable_at_boot(crtc);
+
ret = drm_dev_register(drm, 0);
if (ret < 0)
goto unbind_all;
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 860be019d8e3..1a97545b9244 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -813,6 +813,7 @@ void vc4_bo_remove_from_purgeable_pool(struct vc4_bo *bo);
/* vc4_crtc.c */
extern struct platform_driver vc4_crtc_driver;
+int vc4_crtc_disable_at_boot(struct drm_crtc *crtc);
int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
const struct drm_crtc_funcs *crtc_funcs,
const struct drm_crtc_helper_funcs *crtc_helper_funcs);
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 35/80] drm/vc4: drv: Disable the CRTC at boot time
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to prevent issues during the firmware to KMS transition, we need
to make sure the pixelvalve are disabled at boot time so that the DRM state
matches the hardware state.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 25 +++++++++++++++++++++++++
drivers/gpu/drm/vc4/vc4_drv.c | 4 ++++
drivers/gpu/drm/vc4/vc4_drv.h | 1 +
3 files changed, 30 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 4156c5f66877..dfac304fe2b0 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -427,6 +427,31 @@ static int vc4_crtc_disable(struct drm_crtc *crtc, unsigned int channel)
return 0;
}
+int vc4_crtc_disable_at_boot(struct drm_crtc *crtc)
+{
+ struct drm_device *drm = crtc->dev;
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ int channel;
+
+ if (!(of_device_is_compatible(vc4_crtc->pdev->dev.of_node,
+ "brcm,bcm2711-pixelvalve2") ||
+ of_device_is_compatible(vc4_crtc->pdev->dev.of_node,
+ "brcm,bcm2711-pixelvalve4")))
+ return 0;
+
+ if (!(CRTC_READ(PV_CONTROL) & PV_CONTROL_EN))
+ return 0;
+
+ if (!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN))
+ return 0;
+
+ channel = vc4_hvs_get_fifo_from_output(drm, vc4_crtc->data->hvs_output);
+ if (channel < 0)
+ return 0;
+
+ return vc4_crtc_disable(crtc, channel);
+}
+
static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
struct drm_crtc_state *old_state)
{
diff --git a/drivers/gpu/drm/vc4/vc4_drv.c b/drivers/gpu/drm/vc4/vc4_drv.c
index 38343d2fb4fb..9567d1019212 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.c
+++ b/drivers/gpu/drm/vc4/vc4_drv.c
@@ -252,6 +252,7 @@ static int vc4_drm_bind(struct device *dev)
struct drm_device *drm;
struct vc4_dev *vc4;
struct device_node *node;
+ struct drm_crtc *crtc;
int ret = 0;
dev->coherent_dma_mask = DMA_BIT_MASK(32);
@@ -298,6 +299,9 @@ static int vc4_drm_bind(struct device *dev)
if (ret < 0)
goto unbind_all;
+ drm_for_each_crtc(crtc, drm)
+ vc4_crtc_disable_at_boot(crtc);
+
ret = drm_dev_register(drm, 0);
if (ret < 0)
goto unbind_all;
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 860be019d8e3..1a97545b9244 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -813,6 +813,7 @@ void vc4_bo_remove_from_purgeable_pool(struct vc4_bo *bo);
/* vc4_crtc.c */
extern struct platform_driver vc4_crtc_driver;
+int vc4_crtc_disable_at_boot(struct drm_crtc *crtc);
int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
const struct drm_crtc_funcs *crtc_funcs,
const struct drm_crtc_helper_funcs *crtc_helper_funcs);
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 35/80] drm/vc4: drv: Disable the CRTC at boot time
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
In order to prevent issues during the firmware to KMS transition, we need
to make sure the pixelvalve are disabled at boot time so that the DRM state
matches the hardware state.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 25 +++++++++++++++++++++++++
drivers/gpu/drm/vc4/vc4_drv.c | 4 ++++
drivers/gpu/drm/vc4/vc4_drv.h | 1 +
3 files changed, 30 insertions(+)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index 4156c5f66877..dfac304fe2b0 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -427,6 +427,31 @@ static int vc4_crtc_disable(struct drm_crtc *crtc, unsigned int channel)
return 0;
}
+int vc4_crtc_disable_at_boot(struct drm_crtc *crtc)
+{
+ struct drm_device *drm = crtc->dev;
+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
+ int channel;
+
+ if (!(of_device_is_compatible(vc4_crtc->pdev->dev.of_node,
+ "brcm,bcm2711-pixelvalve2") ||
+ of_device_is_compatible(vc4_crtc->pdev->dev.of_node,
+ "brcm,bcm2711-pixelvalve4")))
+ return 0;
+
+ if (!(CRTC_READ(PV_CONTROL) & PV_CONTROL_EN))
+ return 0;
+
+ if (!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN))
+ return 0;
+
+ channel = vc4_hvs_get_fifo_from_output(drm, vc4_crtc->data->hvs_output);
+ if (channel < 0)
+ return 0;
+
+ return vc4_crtc_disable(crtc, channel);
+}
+
static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,
struct drm_crtc_state *old_state)
{
diff --git a/drivers/gpu/drm/vc4/vc4_drv.c b/drivers/gpu/drm/vc4/vc4_drv.c
index 38343d2fb4fb..9567d1019212 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.c
+++ b/drivers/gpu/drm/vc4/vc4_drv.c
@@ -252,6 +252,7 @@ static int vc4_drm_bind(struct device *dev)
struct drm_device *drm;
struct vc4_dev *vc4;
struct device_node *node;
+ struct drm_crtc *crtc;
int ret = 0;
dev->coherent_dma_mask = DMA_BIT_MASK(32);
@@ -298,6 +299,9 @@ static int vc4_drm_bind(struct device *dev)
if (ret < 0)
goto unbind_all;
+ drm_for_each_crtc(crtc, drm)
+ vc4_crtc_disable_at_boot(crtc);
+
ret = drm_dev_register(drm, 0);
if (ret < 0)
goto unbind_all;
diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h
index 860be019d8e3..1a97545b9244 100644
--- a/drivers/gpu/drm/vc4/vc4_drv.h
+++ b/drivers/gpu/drm/vc4/vc4_drv.h
@@ -813,6 +813,7 @@ void vc4_bo_remove_from_purgeable_pool(struct vc4_bo *bo);
/* vc4_crtc.c */
extern struct platform_driver vc4_crtc_driver;
+int vc4_crtc_disable_at_boot(struct drm_crtc *crtc);
int vc4_crtc_init(struct drm_device *drm, struct vc4_crtc *vc4_crtc,
const struct drm_crtc_funcs *crtc_funcs,
const struct drm_crtc_helper_funcs *crtc_helper_funcs);
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 36/80] dt-bindings: display: vc4: pv: Add BCM2711 pixel valves
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Rob Herring, Chanwoo Choi,
Hoegeun Kwon, Stefan Wahren
The BCM2711 comes with other pixelvalves that have different requirements
and capabilities. Let's document their compatible.
Reviewed-by: Rob Herring <robh+dt@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml
index e60791db1fa1..4e1ba03f6477 100644
--- a/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml
+++ b/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml
@@ -15,6 +15,11 @@ properties:
- brcm,bcm2835-pixelvalve0
- brcm,bcm2835-pixelvalve1
- brcm,bcm2835-pixelvalve2
+ - brcm,bcm2711-pixelvalve0
+ - brcm,bcm2711-pixelvalve1
+ - brcm,bcm2711-pixelvalve2
+ - brcm,bcm2711-pixelvalve3
+ - brcm,bcm2711-pixelvalve4
reg:
maxItems: 1
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 36/80] dt-bindings: display: vc4: pv: Add BCM2711 pixel valves
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, Rob Herring,
bcm-kernel-feedback-list, linux-rpi-kernel, Phil Elwell,
linux-arm-kernel, Maxime Ripard
The BCM2711 comes with other pixelvalves that have different requirements
and capabilities. Let's document their compatible.
Reviewed-by: Rob Herring <robh+dt@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml
index e60791db1fa1..4e1ba03f6477 100644
--- a/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml
+++ b/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml
@@ -15,6 +15,11 @@ properties:
- brcm,bcm2835-pixelvalve0
- brcm,bcm2835-pixelvalve1
- brcm,bcm2835-pixelvalve2
+ - brcm,bcm2711-pixelvalve0
+ - brcm,bcm2711-pixelvalve1
+ - brcm,bcm2711-pixelvalve2
+ - brcm,bcm2711-pixelvalve3
+ - brcm,bcm2711-pixelvalve4
reg:
maxItems: 1
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 36/80] dt-bindings: display: vc4: pv: Add BCM2711 pixel valves
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, Rob Herring,
bcm-kernel-feedback-list, linux-rpi-kernel, Phil Elwell,
linux-arm-kernel, Maxime Ripard
The BCM2711 comes with other pixelvalves that have different requirements
and capabilities. Let's document their compatible.
Reviewed-by: Rob Herring <robh+dt@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml
index e60791db1fa1..4e1ba03f6477 100644
--- a/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml
+++ b/Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml
@@ -15,6 +15,11 @@ properties:
- brcm,bcm2835-pixelvalve0
- brcm,bcm2835-pixelvalve1
- brcm,bcm2835-pixelvalve2
+ - brcm,bcm2711-pixelvalve0
+ - brcm,bcm2711-pixelvalve1
+ - brcm,bcm2711-pixelvalve2
+ - brcm,bcm2711-pixelvalve3
+ - brcm,bcm2711-pixelvalve4
reg:
maxItems: 1
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 37/80] drm/vc4: crtc: Add BCM2711 pixelvalves
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The BCM2711 has 5 pixelvalves, so now that our driver is ready, let's add
support for them.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 95 ++++++++++++++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_regs.h | 7 +++-
2 files changed, 100 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index dfac304fe2b0..a393f93390a2 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -208,6 +208,7 @@ void vc4_crtc_destroy(struct drm_crtc *crtc)
static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
{
+ const struct vc4_crtc_data *crtc_data = vc4_crtc_to_vc4_crtc_data(vc4_crtc);
const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc);
u32 fifo_len_bytes = pv_data->fifo_depth;
@@ -230,6 +231,13 @@ static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
case PV_CONTROL_FORMAT_24:
case PV_CONTROL_FORMAT_DSIV_24:
default:
+ /*
+ * For some reason, the pixelvalve4 doesn't work with
+ * the usual formula and will only work with 32.
+ */
+ if (crtc_data->hvs_output == 5)
+ return 32;
+
return fifo_len_bytes - 3 * HVS_FIFO_LATENCY_PIX;
}
}
@@ -238,9 +246,13 @@ static u32 vc4_crtc_get_fifo_full_level_bits(struct vc4_crtc *vc4_crtc,
u32 format)
{
u32 level = vc4_get_fifo_full_level(vc4_crtc, format);
+ u32 ret = 0;
+
+ ret |= VC4_SET_FIELD((level >> 6),
+ PV5_CONTROL_FIFO_LEVEL_HIGH);
- return VC4_SET_FIELD(level & 0x3f,
- PV_CONTROL_FIFO_LEVEL);
+ return ret | VC4_SET_FIELD(level & 0x3f,
+ PV_CONTROL_FIFO_LEVEL);
}
/*
@@ -278,6 +290,8 @@ static void vc4_crtc_pixelvalve_reset(struct drm_crtc *crtc)
static void vc4_crtc_config_pv(struct drm_crtc *crtc)
{
+ struct drm_device *dev = crtc->dev;
+ struct vc4_dev *vc4 = to_vc4_dev(dev);
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
@@ -358,6 +372,11 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
if (is_dsi)
CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
+ if (vc4->hvs->hvs5)
+ CRTC_WRITE(PV_MUX_CFG,
+ VC4_SET_FIELD(PV_MUX_CFG_RGB_PIXEL_MUX_MODE_NO_SWAP,
+ PV_MUX_CFG_RGB_PIXEL_MUX_MODE));
+
CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR |
vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) |
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
@@ -907,10 +926,82 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
},
};
+static const struct vc4_pv_data bcm2711_pv0_data = {
+ .base = {
+ .hvs_available_channels = BIT(0),
+ .hvs_output = 0,
+ },
+ .debugfs_name = "crtc0_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 1,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_DSI0,
+ [1] = VC4_ENCODER_TYPE_DPI,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv1_data = {
+ .base = {
+ .hvs_available_channels = BIT(0) | BIT(1) | BIT(2),
+ .hvs_output = 3,
+ },
+ .debugfs_name = "crtc1_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 1,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_DSI1,
+ [1] = VC4_ENCODER_TYPE_SMI,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv2_data = {
+ .base = {
+ .hvs_available_channels = BIT(0) | BIT(1) | BIT(2),
+ .hvs_output = 4,
+ },
+ .debugfs_name = "crtc2_regs",
+ .fifo_depth = 256,
+ .pixels_per_clock = 2,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_HDMI0,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv3_data = {
+ .base = {
+ .hvs_available_channels = BIT(1),
+ .hvs_output = 1,
+ },
+ .debugfs_name = "crtc3_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 1,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_VEC,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv4_data = {
+ .base = {
+ .hvs_available_channels = BIT(0) | BIT(1) | BIT(2),
+ .hvs_output = 5,
+ },
+ .debugfs_name = "crtc4_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 2,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_HDMI1,
+ },
+};
+
static const struct of_device_id vc4_crtc_dt_match[] = {
{ .compatible = "brcm,bcm2835-pixelvalve0", .data = &bcm2835_pv0_data },
{ .compatible = "brcm,bcm2835-pixelvalve1", .data = &bcm2835_pv1_data },
{ .compatible = "brcm,bcm2835-pixelvalve2", .data = &bcm2835_pv2_data },
+ { .compatible = "brcm,bcm2711-pixelvalve0", .data = &bcm2711_pv0_data },
+ { .compatible = "brcm,bcm2711-pixelvalve1", .data = &bcm2711_pv1_data },
+ { .compatible = "brcm,bcm2711-pixelvalve2", .data = &bcm2711_pv2_data },
+ { .compatible = "brcm,bcm2711-pixelvalve3", .data = &bcm2711_pv3_data },
+ { .compatible = "brcm,bcm2711-pixelvalve4", .data = &bcm2711_pv4_data },
{}
};
diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h
index 7fbac68b6fe1..c0031ab19689 100644
--- a/drivers/gpu/drm/vc4/vc4_regs.h
+++ b/drivers/gpu/drm/vc4/vc4_regs.h
@@ -129,6 +129,8 @@
#define V3D_ERRSTAT 0x00f20
#define PV_CONTROL 0x00
+# define PV5_CONTROL_FIFO_LEVEL_HIGH_MASK VC4_MASK(26, 25)
+# define PV5_CONTROL_FIFO_LEVEL_HIGH_SHIFT 25
# define PV_CONTROL_FORMAT_MASK VC4_MASK(23, 21)
# define PV_CONTROL_FORMAT_SHIFT 21
# define PV_CONTROL_FORMAT_24 0
@@ -208,6 +210,11 @@
#define PV_HACT_ACT 0x30
+#define PV_MUX_CFG 0x34
+# define PV_MUX_CFG_RGB_PIXEL_MUX_MODE_MASK VC4_MASK(5, 2)
+# define PV_MUX_CFG_RGB_PIXEL_MUX_MODE_SHIFT 2
+# define PV_MUX_CFG_RGB_PIXEL_MUX_MODE_NO_SWAP 8
+
#define SCALER_CHANNELS_COUNT 3
#define SCALER_DISPCTRL 0x00000000
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 37/80] drm/vc4: crtc: Add BCM2711 pixelvalves
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The BCM2711 has 5 pixelvalves, so now that our driver is ready, let's add
support for them.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 95 ++++++++++++++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_regs.h | 7 +++-
2 files changed, 100 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index dfac304fe2b0..a393f93390a2 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -208,6 +208,7 @@ void vc4_crtc_destroy(struct drm_crtc *crtc)
static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
{
+ const struct vc4_crtc_data *crtc_data = vc4_crtc_to_vc4_crtc_data(vc4_crtc);
const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc);
u32 fifo_len_bytes = pv_data->fifo_depth;
@@ -230,6 +231,13 @@ static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
case PV_CONTROL_FORMAT_24:
case PV_CONTROL_FORMAT_DSIV_24:
default:
+ /*
+ * For some reason, the pixelvalve4 doesn't work with
+ * the usual formula and will only work with 32.
+ */
+ if (crtc_data->hvs_output == 5)
+ return 32;
+
return fifo_len_bytes - 3 * HVS_FIFO_LATENCY_PIX;
}
}
@@ -238,9 +246,13 @@ static u32 vc4_crtc_get_fifo_full_level_bits(struct vc4_crtc *vc4_crtc,
u32 format)
{
u32 level = vc4_get_fifo_full_level(vc4_crtc, format);
+ u32 ret = 0;
+
+ ret |= VC4_SET_FIELD((level >> 6),
+ PV5_CONTROL_FIFO_LEVEL_HIGH);
- return VC4_SET_FIELD(level & 0x3f,
- PV_CONTROL_FIFO_LEVEL);
+ return ret | VC4_SET_FIELD(level & 0x3f,
+ PV_CONTROL_FIFO_LEVEL);
}
/*
@@ -278,6 +290,8 @@ static void vc4_crtc_pixelvalve_reset(struct drm_crtc *crtc)
static void vc4_crtc_config_pv(struct drm_crtc *crtc)
{
+ struct drm_device *dev = crtc->dev;
+ struct vc4_dev *vc4 = to_vc4_dev(dev);
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
@@ -358,6 +372,11 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
if (is_dsi)
CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
+ if (vc4->hvs->hvs5)
+ CRTC_WRITE(PV_MUX_CFG,
+ VC4_SET_FIELD(PV_MUX_CFG_RGB_PIXEL_MUX_MODE_NO_SWAP,
+ PV_MUX_CFG_RGB_PIXEL_MUX_MODE));
+
CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR |
vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) |
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
@@ -907,10 +926,82 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
},
};
+static const struct vc4_pv_data bcm2711_pv0_data = {
+ .base = {
+ .hvs_available_channels = BIT(0),
+ .hvs_output = 0,
+ },
+ .debugfs_name = "crtc0_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 1,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_DSI0,
+ [1] = VC4_ENCODER_TYPE_DPI,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv1_data = {
+ .base = {
+ .hvs_available_channels = BIT(0) | BIT(1) | BIT(2),
+ .hvs_output = 3,
+ },
+ .debugfs_name = "crtc1_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 1,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_DSI1,
+ [1] = VC4_ENCODER_TYPE_SMI,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv2_data = {
+ .base = {
+ .hvs_available_channels = BIT(0) | BIT(1) | BIT(2),
+ .hvs_output = 4,
+ },
+ .debugfs_name = "crtc2_regs",
+ .fifo_depth = 256,
+ .pixels_per_clock = 2,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_HDMI0,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv3_data = {
+ .base = {
+ .hvs_available_channels = BIT(1),
+ .hvs_output = 1,
+ },
+ .debugfs_name = "crtc3_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 1,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_VEC,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv4_data = {
+ .base = {
+ .hvs_available_channels = BIT(0) | BIT(1) | BIT(2),
+ .hvs_output = 5,
+ },
+ .debugfs_name = "crtc4_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 2,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_HDMI1,
+ },
+};
+
static const struct of_device_id vc4_crtc_dt_match[] = {
{ .compatible = "brcm,bcm2835-pixelvalve0", .data = &bcm2835_pv0_data },
{ .compatible = "brcm,bcm2835-pixelvalve1", .data = &bcm2835_pv1_data },
{ .compatible = "brcm,bcm2835-pixelvalve2", .data = &bcm2835_pv2_data },
+ { .compatible = "brcm,bcm2711-pixelvalve0", .data = &bcm2711_pv0_data },
+ { .compatible = "brcm,bcm2711-pixelvalve1", .data = &bcm2711_pv1_data },
+ { .compatible = "brcm,bcm2711-pixelvalve2", .data = &bcm2711_pv2_data },
+ { .compatible = "brcm,bcm2711-pixelvalve3", .data = &bcm2711_pv3_data },
+ { .compatible = "brcm,bcm2711-pixelvalve4", .data = &bcm2711_pv4_data },
{}
};
diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h
index 7fbac68b6fe1..c0031ab19689 100644
--- a/drivers/gpu/drm/vc4/vc4_regs.h
+++ b/drivers/gpu/drm/vc4/vc4_regs.h
@@ -129,6 +129,8 @@
#define V3D_ERRSTAT 0x00f20
#define PV_CONTROL 0x00
+# define PV5_CONTROL_FIFO_LEVEL_HIGH_MASK VC4_MASK(26, 25)
+# define PV5_CONTROL_FIFO_LEVEL_HIGH_SHIFT 25
# define PV_CONTROL_FORMAT_MASK VC4_MASK(23, 21)
# define PV_CONTROL_FORMAT_SHIFT 21
# define PV_CONTROL_FORMAT_24 0
@@ -208,6 +210,11 @@
#define PV_HACT_ACT 0x30
+#define PV_MUX_CFG 0x34
+# define PV_MUX_CFG_RGB_PIXEL_MUX_MODE_MASK VC4_MASK(5, 2)
+# define PV_MUX_CFG_RGB_PIXEL_MUX_MODE_SHIFT 2
+# define PV_MUX_CFG_RGB_PIXEL_MUX_MODE_NO_SWAP 8
+
#define SCALER_CHANNELS_COUNT 3
#define SCALER_DISPCTRL 0x00000000
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 37/80] drm/vc4: crtc: Add BCM2711 pixelvalves
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The BCM2711 has 5 pixelvalves, so now that our driver is ready, let's add
support for them.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_crtc.c | 95 ++++++++++++++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_regs.h | 7 +++-
2 files changed, 100 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c
index dfac304fe2b0..a393f93390a2 100644
--- a/drivers/gpu/drm/vc4/vc4_crtc.c
+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
@@ -208,6 +208,7 @@ void vc4_crtc_destroy(struct drm_crtc *crtc)
static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
{
+ const struct vc4_crtc_data *crtc_data = vc4_crtc_to_vc4_crtc_data(vc4_crtc);
const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc);
u32 fifo_len_bytes = pv_data->fifo_depth;
@@ -230,6 +231,13 @@ static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format)
case PV_CONTROL_FORMAT_24:
case PV_CONTROL_FORMAT_DSIV_24:
default:
+ /*
+ * For some reason, the pixelvalve4 doesn't work with
+ * the usual formula and will only work with 32.
+ */
+ if (crtc_data->hvs_output == 5)
+ return 32;
+
return fifo_len_bytes - 3 * HVS_FIFO_LATENCY_PIX;
}
}
@@ -238,9 +246,13 @@ static u32 vc4_crtc_get_fifo_full_level_bits(struct vc4_crtc *vc4_crtc,
u32 format)
{
u32 level = vc4_get_fifo_full_level(vc4_crtc, format);
+ u32 ret = 0;
+
+ ret |= VC4_SET_FIELD((level >> 6),
+ PV5_CONTROL_FIFO_LEVEL_HIGH);
- return VC4_SET_FIELD(level & 0x3f,
- PV_CONTROL_FIFO_LEVEL);
+ return ret | VC4_SET_FIELD(level & 0x3f,
+ PV_CONTROL_FIFO_LEVEL);
}
/*
@@ -278,6 +290,8 @@ static void vc4_crtc_pixelvalve_reset(struct drm_crtc *crtc)
static void vc4_crtc_config_pv(struct drm_crtc *crtc)
{
+ struct drm_device *dev = crtc->dev;
+ struct vc4_dev *vc4 = to_vc4_dev(dev);
struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
@@ -358,6 +372,11 @@ static void vc4_crtc_config_pv(struct drm_crtc *crtc)
if (is_dsi)
CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
+ if (vc4->hvs->hvs5)
+ CRTC_WRITE(PV_MUX_CFG,
+ VC4_SET_FIELD(PV_MUX_CFG_RGB_PIXEL_MUX_MODE_NO_SWAP,
+ PV_MUX_CFG_RGB_PIXEL_MUX_MODE));
+
CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR |
vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) |
VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
@@ -907,10 +926,82 @@ static const struct vc4_pv_data bcm2835_pv2_data = {
},
};
+static const struct vc4_pv_data bcm2711_pv0_data = {
+ .base = {
+ .hvs_available_channels = BIT(0),
+ .hvs_output = 0,
+ },
+ .debugfs_name = "crtc0_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 1,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_DSI0,
+ [1] = VC4_ENCODER_TYPE_DPI,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv1_data = {
+ .base = {
+ .hvs_available_channels = BIT(0) | BIT(1) | BIT(2),
+ .hvs_output = 3,
+ },
+ .debugfs_name = "crtc1_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 1,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_DSI1,
+ [1] = VC4_ENCODER_TYPE_SMI,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv2_data = {
+ .base = {
+ .hvs_available_channels = BIT(0) | BIT(1) | BIT(2),
+ .hvs_output = 4,
+ },
+ .debugfs_name = "crtc2_regs",
+ .fifo_depth = 256,
+ .pixels_per_clock = 2,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_HDMI0,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv3_data = {
+ .base = {
+ .hvs_available_channels = BIT(1),
+ .hvs_output = 1,
+ },
+ .debugfs_name = "crtc3_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 1,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_VEC,
+ },
+};
+
+static const struct vc4_pv_data bcm2711_pv4_data = {
+ .base = {
+ .hvs_available_channels = BIT(0) | BIT(1) | BIT(2),
+ .hvs_output = 5,
+ },
+ .debugfs_name = "crtc4_regs",
+ .fifo_depth = 64,
+ .pixels_per_clock = 2,
+ .encoder_types = {
+ [0] = VC4_ENCODER_TYPE_HDMI1,
+ },
+};
+
static const struct of_device_id vc4_crtc_dt_match[] = {
{ .compatible = "brcm,bcm2835-pixelvalve0", .data = &bcm2835_pv0_data },
{ .compatible = "brcm,bcm2835-pixelvalve1", .data = &bcm2835_pv1_data },
{ .compatible = "brcm,bcm2835-pixelvalve2", .data = &bcm2835_pv2_data },
+ { .compatible = "brcm,bcm2711-pixelvalve0", .data = &bcm2711_pv0_data },
+ { .compatible = "brcm,bcm2711-pixelvalve1", .data = &bcm2711_pv1_data },
+ { .compatible = "brcm,bcm2711-pixelvalve2", .data = &bcm2711_pv2_data },
+ { .compatible = "brcm,bcm2711-pixelvalve3", .data = &bcm2711_pv3_data },
+ { .compatible = "brcm,bcm2711-pixelvalve4", .data = &bcm2711_pv4_data },
{}
};
diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h
index 7fbac68b6fe1..c0031ab19689 100644
--- a/drivers/gpu/drm/vc4/vc4_regs.h
+++ b/drivers/gpu/drm/vc4/vc4_regs.h
@@ -129,6 +129,8 @@
#define V3D_ERRSTAT 0x00f20
#define PV_CONTROL 0x00
+# define PV5_CONTROL_FIFO_LEVEL_HIGH_MASK VC4_MASK(26, 25)
+# define PV5_CONTROL_FIFO_LEVEL_HIGH_SHIFT 25
# define PV_CONTROL_FORMAT_MASK VC4_MASK(23, 21)
# define PV_CONTROL_FORMAT_SHIFT 21
# define PV_CONTROL_FORMAT_24 0
@@ -208,6 +210,11 @@
#define PV_HACT_ACT 0x30
+#define PV_MUX_CFG 0x34
+# define PV_MUX_CFG_RGB_PIXEL_MUX_MODE_MASK VC4_MASK(5, 2)
+# define PV_MUX_CFG_RGB_PIXEL_MUX_MODE_SHIFT 2
+# define PV_MUX_CFG_RGB_PIXEL_MUX_MODE_NO_SWAP 8
+
#define SCALER_CHANNELS_COUNT 3
#define SCALER_DISPCTRL 0x00000000
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 38/80] drm/vc4: hdmi: Use debugfs private field
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
We're calling vc4_debugfs_add_file with our struct vc4_hdmi pointer set
in the private field, but we don't use that field and go through the
main struct vc4_dev to get it.
Let's use the private field directly, that will save us some trouble
later on.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index ec34c08b16df..ae8c4d53e239 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -183,9 +183,7 @@ static const struct debugfs_reg32 hd_regs[] = {
static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
{
struct drm_info_node *node = (struct drm_info_node *)m->private;
- struct drm_device *dev = node->minor->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *hdmi = node->info_ent->data;
struct drm_printer p = drm_seq_file_printer(m);
drm_print_regset32(&p, &hdmi->hdmi_regset);
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 38/80] drm/vc4: hdmi: Use debugfs private field
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
We're calling vc4_debugfs_add_file with our struct vc4_hdmi pointer set
in the private field, but we don't use that field and go through the
main struct vc4_dev to get it.
Let's use the private field directly, that will save us some trouble
later on.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index ec34c08b16df..ae8c4d53e239 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -183,9 +183,7 @@ static const struct debugfs_reg32 hd_regs[] = {
static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
{
struct drm_info_node *node = (struct drm_info_node *)m->private;
- struct drm_device *dev = node->minor->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *hdmi = node->info_ent->data;
struct drm_printer p = drm_seq_file_printer(m);
drm_print_regset32(&p, &hdmi->hdmi_regset);
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 38/80] drm/vc4: hdmi: Use debugfs private field
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
We're calling vc4_debugfs_add_file with our struct vc4_hdmi pointer set
in the private field, but we don't use that field and go through the
main struct vc4_dev to get it.
Let's use the private field directly, that will save us some trouble
later on.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index ec34c08b16df..ae8c4d53e239 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -183,9 +183,7 @@ static const struct debugfs_reg32 hd_regs[] = {
static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
{
struct drm_info_node *node = (struct drm_info_node *)m->private;
- struct drm_device *dev = node->minor->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *hdmi = node->info_ent->data;
struct drm_printer p = drm_seq_file_printer(m);
drm_print_regset32(&p, &hdmi->hdmi_regset);
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 39/80] drm/vc4: hdmi: Move structure to header
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
We will need to share the vc4_hdmi and related structures with multiple
files, so let's create a header for it.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 76 +-------------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 86 +++++++++++++++++++++++++++++++++++-
2 files changed, 87 insertions(+), 75 deletions(-)
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index ae8c4d53e239..5c4d2fee6b86 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -49,87 +49,13 @@
#include <sound/soc.h>
#include "media/cec.h"
#include "vc4_drv.h"
+#include "vc4_hdmi.h"
#include "vc4_regs.h"
#define HSM_CLOCK_FREQ 163682864
#define CEC_CLOCK_FREQ 40000
#define CEC_CLOCK_DIV (HSM_CLOCK_FREQ / CEC_CLOCK_FREQ)
-/* HDMI audio information */
-struct vc4_hdmi_audio {
- struct snd_soc_card card;
- struct snd_soc_dai_link link;
- struct snd_soc_dai_link_component cpu;
- struct snd_soc_dai_link_component codec;
- struct snd_soc_dai_link_component platform;
- int samplerate;
- int channels;
- struct snd_dmaengine_dai_dma_data dma_data;
- struct snd_pcm_substream *substream;
-};
-
-/* General HDMI hardware state. */
-struct vc4_hdmi {
- struct platform_device *pdev;
-
- struct drm_encoder *encoder;
- struct drm_connector *connector;
-
- struct vc4_hdmi_audio audio;
-
- struct i2c_adapter *ddc;
- void __iomem *hdmicore_regs;
- void __iomem *hd_regs;
- int hpd_gpio;
- bool hpd_active_low;
-
- struct cec_adapter *cec_adap;
- struct cec_msg cec_rx_msg;
- bool cec_tx_ok;
- bool cec_irq_was_rx;
-
- struct clk *pixel_clock;
- struct clk *hsm_clock;
-
- struct debugfs_regset32 hdmi_regset;
- struct debugfs_regset32 hd_regset;
-};
-
-#define HDMI_READ(offset) readl(vc4->hdmi->hdmicore_regs + offset)
-#define HDMI_WRITE(offset, val) writel(val, vc4->hdmi->hdmicore_regs + offset)
-#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
-#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
-
-/* VC4 HDMI encoder KMS struct */
-struct vc4_hdmi_encoder {
- struct vc4_encoder base;
- bool hdmi_monitor;
- bool limited_rgb_range;
-};
-
-static inline struct vc4_hdmi_encoder *
-to_vc4_hdmi_encoder(struct drm_encoder *encoder)
-{
- return container_of(encoder, struct vc4_hdmi_encoder, base.base);
-}
-
-/* VC4 HDMI connector KMS struct */
-struct vc4_hdmi_connector {
- struct drm_connector base;
-
- /* Since the connector is attached to just the one encoder,
- * this is the reference to it so we can do the best_encoder()
- * hook.
- */
- struct drm_encoder *encoder;
-};
-
-static inline struct vc4_hdmi_connector *
-to_vc4_hdmi_connector(struct drm_connector *connector)
-{
- return container_of(connector, struct vc4_hdmi_connector, base);
-}
-
static const struct debugfs_reg32 hdmi_regs[] = {
VC4_REG32(VC4_HDMI_CORE_REV),
VC4_REG32(VC4_HDMI_SW_RESET_CONTROL),
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
new file mode 100644
index 000000000000..5ec5d1f6b1e6
--- /dev/null
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -0,0 +1,86 @@
+#ifndef _VC4_HDMI_H_
+#define _VC4_HDMI_H_
+
+#include <drm/drm_connector.h>
+#include <media/cec.h>
+#include <sound/dmaengine_pcm.h>
+#include <sound/soc.h>
+
+#include "vc4_drv.h"
+
+/* HDMI audio information */
+struct vc4_hdmi_audio {
+ struct snd_soc_card card;
+ struct snd_soc_dai_link link;
+ struct snd_soc_dai_link_component cpu;
+ struct snd_soc_dai_link_component codec;
+ struct snd_soc_dai_link_component platform;
+ int samplerate;
+ int channels;
+ struct snd_dmaengine_dai_dma_data dma_data;
+ struct snd_pcm_substream *substream;
+};
+
+/* General HDMI hardware state. */
+struct vc4_hdmi {
+ struct platform_device *pdev;
+
+ struct drm_encoder *encoder;
+ struct drm_connector *connector;
+
+ struct vc4_hdmi_audio audio;
+
+ struct i2c_adapter *ddc;
+ void __iomem *hdmicore_regs;
+ void __iomem *hd_regs;
+ int hpd_gpio;
+ bool hpd_active_low;
+
+ struct cec_adapter *cec_adap;
+ struct cec_msg cec_rx_msg;
+ bool cec_tx_ok;
+ bool cec_irq_was_rx;
+
+ struct clk *pixel_clock;
+ struct clk *hsm_clock;
+
+ struct debugfs_regset32 hdmi_regset;
+ struct debugfs_regset32 hd_regset;
+};
+
+#define HDMI_READ(offset) readl(vc4->hdmi->hdmicore_regs + offset)
+#define HDMI_WRITE(offset, val) writel(val, vc4->hdmi->hdmicore_regs + offset)
+#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
+#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
+
+/* VC4 HDMI encoder KMS struct */
+struct vc4_hdmi_encoder {
+ struct vc4_encoder base;
+ bool hdmi_monitor;
+ bool limited_rgb_range;
+};
+
+static inline struct vc4_hdmi_encoder *
+to_vc4_hdmi_encoder(struct drm_encoder *encoder)
+{
+ return container_of(encoder, struct vc4_hdmi_encoder, base.base);
+}
+
+/* VC4 HDMI connector KMS struct */
+struct vc4_hdmi_connector {
+ struct drm_connector base;
+
+ /* Since the connector is attached to just the one encoder,
+ * this is the reference to it so we can do the best_encoder()
+ * hook.
+ */
+ struct drm_encoder *encoder;
+};
+
+static inline struct vc4_hdmi_connector *
+to_vc4_hdmi_connector(struct drm_connector *connector)
+{
+ return container_of(connector, struct vc4_hdmi_connector, base);
+}
+
+#endif /* _VC4_HDMI_H_ */
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 39/80] drm/vc4: hdmi: Move structure to header
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
We will need to share the vc4_hdmi and related structures with multiple
files, so let's create a header for it.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 76 +-------------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 86 +++++++++++++++++++++++++++++++++++-
2 files changed, 87 insertions(+), 75 deletions(-)
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index ae8c4d53e239..5c4d2fee6b86 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -49,87 +49,13 @@
#include <sound/soc.h>
#include "media/cec.h"
#include "vc4_drv.h"
+#include "vc4_hdmi.h"
#include "vc4_regs.h"
#define HSM_CLOCK_FREQ 163682864
#define CEC_CLOCK_FREQ 40000
#define CEC_CLOCK_DIV (HSM_CLOCK_FREQ / CEC_CLOCK_FREQ)
-/* HDMI audio information */
-struct vc4_hdmi_audio {
- struct snd_soc_card card;
- struct snd_soc_dai_link link;
- struct snd_soc_dai_link_component cpu;
- struct snd_soc_dai_link_component codec;
- struct snd_soc_dai_link_component platform;
- int samplerate;
- int channels;
- struct snd_dmaengine_dai_dma_data dma_data;
- struct snd_pcm_substream *substream;
-};
-
-/* General HDMI hardware state. */
-struct vc4_hdmi {
- struct platform_device *pdev;
-
- struct drm_encoder *encoder;
- struct drm_connector *connector;
-
- struct vc4_hdmi_audio audio;
-
- struct i2c_adapter *ddc;
- void __iomem *hdmicore_regs;
- void __iomem *hd_regs;
- int hpd_gpio;
- bool hpd_active_low;
-
- struct cec_adapter *cec_adap;
- struct cec_msg cec_rx_msg;
- bool cec_tx_ok;
- bool cec_irq_was_rx;
-
- struct clk *pixel_clock;
- struct clk *hsm_clock;
-
- struct debugfs_regset32 hdmi_regset;
- struct debugfs_regset32 hd_regset;
-};
-
-#define HDMI_READ(offset) readl(vc4->hdmi->hdmicore_regs + offset)
-#define HDMI_WRITE(offset, val) writel(val, vc4->hdmi->hdmicore_regs + offset)
-#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
-#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
-
-/* VC4 HDMI encoder KMS struct */
-struct vc4_hdmi_encoder {
- struct vc4_encoder base;
- bool hdmi_monitor;
- bool limited_rgb_range;
-};
-
-static inline struct vc4_hdmi_encoder *
-to_vc4_hdmi_encoder(struct drm_encoder *encoder)
-{
- return container_of(encoder, struct vc4_hdmi_encoder, base.base);
-}
-
-/* VC4 HDMI connector KMS struct */
-struct vc4_hdmi_connector {
- struct drm_connector base;
-
- /* Since the connector is attached to just the one encoder,
- * this is the reference to it so we can do the best_encoder()
- * hook.
- */
- struct drm_encoder *encoder;
-};
-
-static inline struct vc4_hdmi_connector *
-to_vc4_hdmi_connector(struct drm_connector *connector)
-{
- return container_of(connector, struct vc4_hdmi_connector, base);
-}
-
static const struct debugfs_reg32 hdmi_regs[] = {
VC4_REG32(VC4_HDMI_CORE_REV),
VC4_REG32(VC4_HDMI_SW_RESET_CONTROL),
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
new file mode 100644
index 000000000000..5ec5d1f6b1e6
--- /dev/null
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -0,0 +1,86 @@
+#ifndef _VC4_HDMI_H_
+#define _VC4_HDMI_H_
+
+#include <drm/drm_connector.h>
+#include <media/cec.h>
+#include <sound/dmaengine_pcm.h>
+#include <sound/soc.h>
+
+#include "vc4_drv.h"
+
+/* HDMI audio information */
+struct vc4_hdmi_audio {
+ struct snd_soc_card card;
+ struct snd_soc_dai_link link;
+ struct snd_soc_dai_link_component cpu;
+ struct snd_soc_dai_link_component codec;
+ struct snd_soc_dai_link_component platform;
+ int samplerate;
+ int channels;
+ struct snd_dmaengine_dai_dma_data dma_data;
+ struct snd_pcm_substream *substream;
+};
+
+/* General HDMI hardware state. */
+struct vc4_hdmi {
+ struct platform_device *pdev;
+
+ struct drm_encoder *encoder;
+ struct drm_connector *connector;
+
+ struct vc4_hdmi_audio audio;
+
+ struct i2c_adapter *ddc;
+ void __iomem *hdmicore_regs;
+ void __iomem *hd_regs;
+ int hpd_gpio;
+ bool hpd_active_low;
+
+ struct cec_adapter *cec_adap;
+ struct cec_msg cec_rx_msg;
+ bool cec_tx_ok;
+ bool cec_irq_was_rx;
+
+ struct clk *pixel_clock;
+ struct clk *hsm_clock;
+
+ struct debugfs_regset32 hdmi_regset;
+ struct debugfs_regset32 hd_regset;
+};
+
+#define HDMI_READ(offset) readl(vc4->hdmi->hdmicore_regs + offset)
+#define HDMI_WRITE(offset, val) writel(val, vc4->hdmi->hdmicore_regs + offset)
+#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
+#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
+
+/* VC4 HDMI encoder KMS struct */
+struct vc4_hdmi_encoder {
+ struct vc4_encoder base;
+ bool hdmi_monitor;
+ bool limited_rgb_range;
+};
+
+static inline struct vc4_hdmi_encoder *
+to_vc4_hdmi_encoder(struct drm_encoder *encoder)
+{
+ return container_of(encoder, struct vc4_hdmi_encoder, base.base);
+}
+
+/* VC4 HDMI connector KMS struct */
+struct vc4_hdmi_connector {
+ struct drm_connector base;
+
+ /* Since the connector is attached to just the one encoder,
+ * this is the reference to it so we can do the best_encoder()
+ * hook.
+ */
+ struct drm_encoder *encoder;
+};
+
+static inline struct vc4_hdmi_connector *
+to_vc4_hdmi_connector(struct drm_connector *connector)
+{
+ return container_of(connector, struct vc4_hdmi_connector, base);
+}
+
+#endif /* _VC4_HDMI_H_ */
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 39/80] drm/vc4: hdmi: Move structure to header
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
We will need to share the vc4_hdmi and related structures with multiple
files, so let's create a header for it.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 76 +-------------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 86 +++++++++++++++++++++++++++++++++++-
2 files changed, 87 insertions(+), 75 deletions(-)
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index ae8c4d53e239..5c4d2fee6b86 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -49,87 +49,13 @@
#include <sound/soc.h>
#include "media/cec.h"
#include "vc4_drv.h"
+#include "vc4_hdmi.h"
#include "vc4_regs.h"
#define HSM_CLOCK_FREQ 163682864
#define CEC_CLOCK_FREQ 40000
#define CEC_CLOCK_DIV (HSM_CLOCK_FREQ / CEC_CLOCK_FREQ)
-/* HDMI audio information */
-struct vc4_hdmi_audio {
- struct snd_soc_card card;
- struct snd_soc_dai_link link;
- struct snd_soc_dai_link_component cpu;
- struct snd_soc_dai_link_component codec;
- struct snd_soc_dai_link_component platform;
- int samplerate;
- int channels;
- struct snd_dmaengine_dai_dma_data dma_data;
- struct snd_pcm_substream *substream;
-};
-
-/* General HDMI hardware state. */
-struct vc4_hdmi {
- struct platform_device *pdev;
-
- struct drm_encoder *encoder;
- struct drm_connector *connector;
-
- struct vc4_hdmi_audio audio;
-
- struct i2c_adapter *ddc;
- void __iomem *hdmicore_regs;
- void __iomem *hd_regs;
- int hpd_gpio;
- bool hpd_active_low;
-
- struct cec_adapter *cec_adap;
- struct cec_msg cec_rx_msg;
- bool cec_tx_ok;
- bool cec_irq_was_rx;
-
- struct clk *pixel_clock;
- struct clk *hsm_clock;
-
- struct debugfs_regset32 hdmi_regset;
- struct debugfs_regset32 hd_regset;
-};
-
-#define HDMI_READ(offset) readl(vc4->hdmi->hdmicore_regs + offset)
-#define HDMI_WRITE(offset, val) writel(val, vc4->hdmi->hdmicore_regs + offset)
-#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
-#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
-
-/* VC4 HDMI encoder KMS struct */
-struct vc4_hdmi_encoder {
- struct vc4_encoder base;
- bool hdmi_monitor;
- bool limited_rgb_range;
-};
-
-static inline struct vc4_hdmi_encoder *
-to_vc4_hdmi_encoder(struct drm_encoder *encoder)
-{
- return container_of(encoder, struct vc4_hdmi_encoder, base.base);
-}
-
-/* VC4 HDMI connector KMS struct */
-struct vc4_hdmi_connector {
- struct drm_connector base;
-
- /* Since the connector is attached to just the one encoder,
- * this is the reference to it so we can do the best_encoder()
- * hook.
- */
- struct drm_encoder *encoder;
-};
-
-static inline struct vc4_hdmi_connector *
-to_vc4_hdmi_connector(struct drm_connector *connector)
-{
- return container_of(connector, struct vc4_hdmi_connector, base);
-}
-
static const struct debugfs_reg32 hdmi_regs[] = {
VC4_REG32(VC4_HDMI_CORE_REV),
VC4_REG32(VC4_HDMI_SW_RESET_CONTROL),
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
new file mode 100644
index 000000000000..5ec5d1f6b1e6
--- /dev/null
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -0,0 +1,86 @@
+#ifndef _VC4_HDMI_H_
+#define _VC4_HDMI_H_
+
+#include <drm/drm_connector.h>
+#include <media/cec.h>
+#include <sound/dmaengine_pcm.h>
+#include <sound/soc.h>
+
+#include "vc4_drv.h"
+
+/* HDMI audio information */
+struct vc4_hdmi_audio {
+ struct snd_soc_card card;
+ struct snd_soc_dai_link link;
+ struct snd_soc_dai_link_component cpu;
+ struct snd_soc_dai_link_component codec;
+ struct snd_soc_dai_link_component platform;
+ int samplerate;
+ int channels;
+ struct snd_dmaengine_dai_dma_data dma_data;
+ struct snd_pcm_substream *substream;
+};
+
+/* General HDMI hardware state. */
+struct vc4_hdmi {
+ struct platform_device *pdev;
+
+ struct drm_encoder *encoder;
+ struct drm_connector *connector;
+
+ struct vc4_hdmi_audio audio;
+
+ struct i2c_adapter *ddc;
+ void __iomem *hdmicore_regs;
+ void __iomem *hd_regs;
+ int hpd_gpio;
+ bool hpd_active_low;
+
+ struct cec_adapter *cec_adap;
+ struct cec_msg cec_rx_msg;
+ bool cec_tx_ok;
+ bool cec_irq_was_rx;
+
+ struct clk *pixel_clock;
+ struct clk *hsm_clock;
+
+ struct debugfs_regset32 hdmi_regset;
+ struct debugfs_regset32 hd_regset;
+};
+
+#define HDMI_READ(offset) readl(vc4->hdmi->hdmicore_regs + offset)
+#define HDMI_WRITE(offset, val) writel(val, vc4->hdmi->hdmicore_regs + offset)
+#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
+#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
+
+/* VC4 HDMI encoder KMS struct */
+struct vc4_hdmi_encoder {
+ struct vc4_encoder base;
+ bool hdmi_monitor;
+ bool limited_rgb_range;
+};
+
+static inline struct vc4_hdmi_encoder *
+to_vc4_hdmi_encoder(struct drm_encoder *encoder)
+{
+ return container_of(encoder, struct vc4_hdmi_encoder, base.base);
+}
+
+/* VC4 HDMI connector KMS struct */
+struct vc4_hdmi_connector {
+ struct drm_connector base;
+
+ /* Since the connector is attached to just the one encoder,
+ * this is the reference to it so we can do the best_encoder()
+ * hook.
+ */
+ struct drm_encoder *encoder;
+};
+
+static inline struct vc4_hdmi_connector *
+to_vc4_hdmi_connector(struct drm_connector *connector)
+{
+ return container_of(connector, struct vc4_hdmi_connector, base);
+}
+
+#endif /* _VC4_HDMI_H_ */
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 40/80] drm/vc4: hdmi: rework connectors and encoders
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
the vc4_hdmi driver has some custom structures to hold the data it needs to
associate with the drm_encoder and drm_connector structures.
However, it allocates them separately from the vc4_hdmi structure which
makes it more complicated than it needs to be.
Move those structures to be contained by vc4_hdmi and update the code
accordingly.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 87 ++++++++++++++++-------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 64 +++++++++++++-------------
2 files changed, 72 insertions(+), 79 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 5c4d2fee6b86..9a0612a87fb8 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -191,20 +191,15 @@ static const struct drm_connector_helper_funcs vc4_hdmi_connector_helper_funcs =
.get_modes = vc4_hdmi_connector_get_modes,
};
-static struct drm_connector *vc4_hdmi_connector_init(struct drm_device *dev,
- struct drm_encoder *encoder,
- struct i2c_adapter *ddc)
+static int vc4_hdmi_connector_init(struct drm_device *dev,
+ struct vc4_hdmi *vc4_hdmi,
+ struct i2c_adapter *ddc)
{
- struct drm_connector *connector;
- struct vc4_hdmi_connector *hdmi_connector;
+ struct vc4_hdmi_connector *hdmi_connector = &vc4_hdmi->connector;
+ struct drm_connector *connector = &hdmi_connector->base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
int ret;
- hdmi_connector = devm_kzalloc(dev->dev, sizeof(*hdmi_connector),
- GFP_KERNEL);
- if (!hdmi_connector)
- return ERR_PTR(-ENOMEM);
- connector = &hdmi_connector->base;
-
hdmi_connector->encoder = encoder;
drm_connector_init_with_ddc(dev, connector,
@@ -216,7 +211,7 @@ static struct drm_connector *vc4_hdmi_connector_init(struct drm_device *dev,
/* Create and attach TV margin props to this connector. */
ret = drm_mode_create_tv_margin_properties(dev);
if (ret)
- return ERR_PTR(ret);
+ return ret;
drm_connector_attach_tv_margin_properties(connector);
@@ -228,7 +223,7 @@ static struct drm_connector *vc4_hdmi_connector_init(struct drm_device *dev,
drm_connector_attach_encoder(connector, encoder);
- return connector;
+ return 0;
}
static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
@@ -298,21 +293,22 @@ static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
struct vc4_dev *vc4 = encoder->dev->dev_private;
struct vc4_hdmi *hdmi = vc4->hdmi;
- struct drm_connector_state *cstate = hdmi->connector->state;
+ struct drm_connector *connector = &hdmi->connector.base;
+ struct drm_connector_state *cstate = connector->state;
struct drm_crtc *crtc = encoder->crtc;
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
union hdmi_infoframe frame;
int ret;
ret = drm_hdmi_avi_infoframe_from_display_mode(&frame.avi,
- hdmi->connector, mode);
+ connector, mode);
if (ret < 0) {
DRM_ERROR("couldn't fill AVI infoframe\n");
return;
}
drm_hdmi_avi_infoframe_quant_range(&frame.avi,
- hdmi->connector, mode,
+ connector, mode,
vc4_encoder->limited_rgb_range ?
HDMI_QUANTIZATION_RANGE_LIMITED :
HDMI_QUANTIZATION_RANGE_FULL);
@@ -628,7 +624,8 @@ static const struct drm_encoder_helper_funcs vc4_hdmi_encoder_helper_funcs = {
/* HDMI audio codec callbacks */
static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
{
- struct drm_device *drm = hdmi->encoder->dev;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 hsm_clock = clk_get_rate(hdmi->hsm_clock);
unsigned long n, m;
@@ -647,7 +644,7 @@ static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
static void vc4_hdmi_set_n_cts(struct vc4_hdmi *hdmi)
{
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_crtc *crtc = encoder->crtc;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -685,7 +682,8 @@ static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_connector *connector = &hdmi->connector.base;
struct vc4_dev *vc4 = to_vc4_dev(encoder->dev);
int ret;
@@ -702,8 +700,7 @@ static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
VC4_HDMI_RAM_PACKET_ENABLE))
return -ENODEV;
- ret = snd_pcm_hw_constraint_eld(substream->runtime,
- hdmi->connector->eld);
+ ret = snd_pcm_hw_constraint_eld(substream->runtime, connector->eld);
if (ret)
return ret;
@@ -717,7 +714,7 @@ static int vc4_hdmi_audio_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
static void vc4_hdmi_audio_reset(struct vc4_hdmi *hdmi)
{
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct device *dev = &hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -751,7 +748,7 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct device *dev = &hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -824,7 +821,7 @@ static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -868,9 +865,10 @@ static int vc4_hdmi_audio_eld_ctl_info(struct snd_kcontrol *kcontrol,
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &hdmi->connector.base;
uinfo->type = SNDRV_CTL_ELEM_TYPE_BYTES;
- uinfo->count = sizeof(hdmi->connector->eld);
+ uinfo->count = sizeof(connector->eld);
return 0;
}
@@ -880,9 +878,10 @@ static int vc4_hdmi_audio_eld_ctl_get(struct snd_kcontrol *kcontrol,
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &hdmi->connector.base;
- memcpy(ucontrol->value.bytes.data, hdmi->connector->eld,
- sizeof(hdmi->connector->eld));
+ memcpy(ucontrol->value.bytes.data, connector->eld,
+ sizeof(connector->eld));
return 0;
}
@@ -1220,7 +1219,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
struct vc4_hdmi *hdmi;
- struct vc4_hdmi_encoder *vc4_hdmi_encoder;
+ struct drm_encoder *encoder;
struct device_node *ddc_node;
u32 value;
int ret;
@@ -1229,14 +1228,10 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
if (!hdmi)
return -ENOMEM;
- vc4_hdmi_encoder = devm_kzalloc(dev, sizeof(*vc4_hdmi_encoder),
- GFP_KERNEL);
- if (!vc4_hdmi_encoder)
- return -ENOMEM;
- vc4_hdmi_encoder->base.type = VC4_ENCODER_TYPE_HDMI0;
- hdmi->encoder = &vc4_hdmi_encoder->base.base;
-
+ encoder = &hdmi->encoder.base.base;
+ hdmi->encoder.base.type = VC4_ENCODER_TYPE_HDMI0;
hdmi->pdev = pdev;
+
hdmi->hdmicore_regs = vc4_ioremap_regs(pdev, 0);
if (IS_ERR(hdmi->hdmicore_regs))
return PTR_ERR(hdmi->hdmicore_regs);
@@ -1324,15 +1319,13 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
}
pm_runtime_enable(dev);
- drm_simple_encoder_init(drm, hdmi->encoder, DRM_MODE_ENCODER_TMDS);
- drm_encoder_helper_add(hdmi->encoder, &vc4_hdmi_encoder_helper_funcs);
+ drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
+ drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
- hdmi->connector =
- vc4_hdmi_connector_init(drm, hdmi->encoder, hdmi->ddc);
- if (IS_ERR(hdmi->connector)) {
- ret = PTR_ERR(hdmi->connector);
+ ret = vc4_hdmi_connector_init(drm, hdmi, hdmi->ddc);
+ if (ret)
goto err_destroy_encoder;
- }
+
#ifdef CONFIG_DRM_VC4_HDMI_CEC
hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
vc4, "vc4",
@@ -1342,7 +1335,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
if (ret < 0)
goto err_destroy_conn;
- cec_fill_conn_info_from_drm(&conn_info, hdmi->connector);
+ cec_fill_conn_info_from_drm(&conn_info, &hdmi->connector.base);
cec_s_conn_info(hdmi->cec_adap, &conn_info);
HDMI_WRITE(VC4_HDMI_CPU_MASK_SET, 0xffffffff);
@@ -1379,10 +1372,10 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
err_delete_cec_adap:
cec_delete_adapter(hdmi->cec_adap);
err_destroy_conn:
- vc4_hdmi_connector_destroy(hdmi->connector);
+ vc4_hdmi_connector_destroy(&hdmi->connector.base);
#endif
err_destroy_encoder:
- drm_encoder_cleanup(hdmi->encoder);
+ drm_encoder_cleanup(encoder);
err_unprepare_hsm:
clk_disable_unprepare(hdmi->hsm_clock);
pm_runtime_disable(dev);
@@ -1400,8 +1393,8 @@ static void vc4_hdmi_unbind(struct device *dev, struct device *master,
struct vc4_hdmi *hdmi = vc4->hdmi;
cec_unregister_adapter(hdmi->cec_adap);
- vc4_hdmi_connector_destroy(hdmi->connector);
- drm_encoder_cleanup(hdmi->encoder);
+ vc4_hdmi_connector_destroy(&hdmi->connector.base);
+ drm_encoder_cleanup(&hdmi->encoder.base.base);
clk_disable_unprepare(hdmi->hsm_clock);
pm_runtime_disable(dev);
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
index 5ec5d1f6b1e6..17079a39f1b1 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -8,6 +8,36 @@
#include "vc4_drv.h"
+/* VC4 HDMI encoder KMS struct */
+struct vc4_hdmi_encoder {
+ struct vc4_encoder base;
+ bool hdmi_monitor;
+ bool limited_rgb_range;
+};
+
+static inline struct vc4_hdmi_encoder *
+to_vc4_hdmi_encoder(struct drm_encoder *encoder)
+{
+ return container_of(encoder, struct vc4_hdmi_encoder, base.base);
+}
+
+/* VC4 HDMI connector KMS struct */
+struct vc4_hdmi_connector {
+ struct drm_connector base;
+
+ /* Since the connector is attached to just the one encoder,
+ * this is the reference to it so we can do the best_encoder()
+ * hook.
+ */
+ struct drm_encoder *encoder;
+};
+
+static inline struct vc4_hdmi_connector *
+to_vc4_hdmi_connector(struct drm_connector *connector)
+{
+ return container_of(connector, struct vc4_hdmi_connector, base);
+}
+
/* HDMI audio information */
struct vc4_hdmi_audio {
struct snd_soc_card card;
@@ -25,8 +55,8 @@ struct vc4_hdmi_audio {
struct vc4_hdmi {
struct platform_device *pdev;
- struct drm_encoder *encoder;
- struct drm_connector *connector;
+ struct vc4_hdmi_encoder encoder;
+ struct vc4_hdmi_connector connector;
struct vc4_hdmi_audio audio;
@@ -53,34 +83,4 @@ struct vc4_hdmi {
#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
-/* VC4 HDMI encoder KMS struct */
-struct vc4_hdmi_encoder {
- struct vc4_encoder base;
- bool hdmi_monitor;
- bool limited_rgb_range;
-};
-
-static inline struct vc4_hdmi_encoder *
-to_vc4_hdmi_encoder(struct drm_encoder *encoder)
-{
- return container_of(encoder, struct vc4_hdmi_encoder, base.base);
-}
-
-/* VC4 HDMI connector KMS struct */
-struct vc4_hdmi_connector {
- struct drm_connector base;
-
- /* Since the connector is attached to just the one encoder,
- * this is the reference to it so we can do the best_encoder()
- * hook.
- */
- struct drm_encoder *encoder;
-};
-
-static inline struct vc4_hdmi_connector *
-to_vc4_hdmi_connector(struct drm_connector *connector)
-{
- return container_of(connector, struct vc4_hdmi_connector, base);
-}
-
#endif /* _VC4_HDMI_H_ */
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 40/80] drm/vc4: hdmi: rework connectors and encoders
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
the vc4_hdmi driver has some custom structures to hold the data it needs to
associate with the drm_encoder and drm_connector structures.
However, it allocates them separately from the vc4_hdmi structure which
makes it more complicated than it needs to be.
Move those structures to be contained by vc4_hdmi and update the code
accordingly.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 87 ++++++++++++++++-------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 64 +++++++++++++-------------
2 files changed, 72 insertions(+), 79 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 5c4d2fee6b86..9a0612a87fb8 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -191,20 +191,15 @@ static const struct drm_connector_helper_funcs vc4_hdmi_connector_helper_funcs =
.get_modes = vc4_hdmi_connector_get_modes,
};
-static struct drm_connector *vc4_hdmi_connector_init(struct drm_device *dev,
- struct drm_encoder *encoder,
- struct i2c_adapter *ddc)
+static int vc4_hdmi_connector_init(struct drm_device *dev,
+ struct vc4_hdmi *vc4_hdmi,
+ struct i2c_adapter *ddc)
{
- struct drm_connector *connector;
- struct vc4_hdmi_connector *hdmi_connector;
+ struct vc4_hdmi_connector *hdmi_connector = &vc4_hdmi->connector;
+ struct drm_connector *connector = &hdmi_connector->base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
int ret;
- hdmi_connector = devm_kzalloc(dev->dev, sizeof(*hdmi_connector),
- GFP_KERNEL);
- if (!hdmi_connector)
- return ERR_PTR(-ENOMEM);
- connector = &hdmi_connector->base;
-
hdmi_connector->encoder = encoder;
drm_connector_init_with_ddc(dev, connector,
@@ -216,7 +211,7 @@ static struct drm_connector *vc4_hdmi_connector_init(struct drm_device *dev,
/* Create and attach TV margin props to this connector. */
ret = drm_mode_create_tv_margin_properties(dev);
if (ret)
- return ERR_PTR(ret);
+ return ret;
drm_connector_attach_tv_margin_properties(connector);
@@ -228,7 +223,7 @@ static struct drm_connector *vc4_hdmi_connector_init(struct drm_device *dev,
drm_connector_attach_encoder(connector, encoder);
- return connector;
+ return 0;
}
static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
@@ -298,21 +293,22 @@ static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
struct vc4_dev *vc4 = encoder->dev->dev_private;
struct vc4_hdmi *hdmi = vc4->hdmi;
- struct drm_connector_state *cstate = hdmi->connector->state;
+ struct drm_connector *connector = &hdmi->connector.base;
+ struct drm_connector_state *cstate = connector->state;
struct drm_crtc *crtc = encoder->crtc;
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
union hdmi_infoframe frame;
int ret;
ret = drm_hdmi_avi_infoframe_from_display_mode(&frame.avi,
- hdmi->connector, mode);
+ connector, mode);
if (ret < 0) {
DRM_ERROR("couldn't fill AVI infoframe\n");
return;
}
drm_hdmi_avi_infoframe_quant_range(&frame.avi,
- hdmi->connector, mode,
+ connector, mode,
vc4_encoder->limited_rgb_range ?
HDMI_QUANTIZATION_RANGE_LIMITED :
HDMI_QUANTIZATION_RANGE_FULL);
@@ -628,7 +624,8 @@ static const struct drm_encoder_helper_funcs vc4_hdmi_encoder_helper_funcs = {
/* HDMI audio codec callbacks */
static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
{
- struct drm_device *drm = hdmi->encoder->dev;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 hsm_clock = clk_get_rate(hdmi->hsm_clock);
unsigned long n, m;
@@ -647,7 +644,7 @@ static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
static void vc4_hdmi_set_n_cts(struct vc4_hdmi *hdmi)
{
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_crtc *crtc = encoder->crtc;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -685,7 +682,8 @@ static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_connector *connector = &hdmi->connector.base;
struct vc4_dev *vc4 = to_vc4_dev(encoder->dev);
int ret;
@@ -702,8 +700,7 @@ static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
VC4_HDMI_RAM_PACKET_ENABLE))
return -ENODEV;
- ret = snd_pcm_hw_constraint_eld(substream->runtime,
- hdmi->connector->eld);
+ ret = snd_pcm_hw_constraint_eld(substream->runtime, connector->eld);
if (ret)
return ret;
@@ -717,7 +714,7 @@ static int vc4_hdmi_audio_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
static void vc4_hdmi_audio_reset(struct vc4_hdmi *hdmi)
{
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct device *dev = &hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -751,7 +748,7 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct device *dev = &hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -824,7 +821,7 @@ static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -868,9 +865,10 @@ static int vc4_hdmi_audio_eld_ctl_info(struct snd_kcontrol *kcontrol,
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &hdmi->connector.base;
uinfo->type = SNDRV_CTL_ELEM_TYPE_BYTES;
- uinfo->count = sizeof(hdmi->connector->eld);
+ uinfo->count = sizeof(connector->eld);
return 0;
}
@@ -880,9 +878,10 @@ static int vc4_hdmi_audio_eld_ctl_get(struct snd_kcontrol *kcontrol,
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &hdmi->connector.base;
- memcpy(ucontrol->value.bytes.data, hdmi->connector->eld,
- sizeof(hdmi->connector->eld));
+ memcpy(ucontrol->value.bytes.data, connector->eld,
+ sizeof(connector->eld));
return 0;
}
@@ -1220,7 +1219,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
struct vc4_hdmi *hdmi;
- struct vc4_hdmi_encoder *vc4_hdmi_encoder;
+ struct drm_encoder *encoder;
struct device_node *ddc_node;
u32 value;
int ret;
@@ -1229,14 +1228,10 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
if (!hdmi)
return -ENOMEM;
- vc4_hdmi_encoder = devm_kzalloc(dev, sizeof(*vc4_hdmi_encoder),
- GFP_KERNEL);
- if (!vc4_hdmi_encoder)
- return -ENOMEM;
- vc4_hdmi_encoder->base.type = VC4_ENCODER_TYPE_HDMI0;
- hdmi->encoder = &vc4_hdmi_encoder->base.base;
-
+ encoder = &hdmi->encoder.base.base;
+ hdmi->encoder.base.type = VC4_ENCODER_TYPE_HDMI0;
hdmi->pdev = pdev;
+
hdmi->hdmicore_regs = vc4_ioremap_regs(pdev, 0);
if (IS_ERR(hdmi->hdmicore_regs))
return PTR_ERR(hdmi->hdmicore_regs);
@@ -1324,15 +1319,13 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
}
pm_runtime_enable(dev);
- drm_simple_encoder_init(drm, hdmi->encoder, DRM_MODE_ENCODER_TMDS);
- drm_encoder_helper_add(hdmi->encoder, &vc4_hdmi_encoder_helper_funcs);
+ drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
+ drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
- hdmi->connector =
- vc4_hdmi_connector_init(drm, hdmi->encoder, hdmi->ddc);
- if (IS_ERR(hdmi->connector)) {
- ret = PTR_ERR(hdmi->connector);
+ ret = vc4_hdmi_connector_init(drm, hdmi, hdmi->ddc);
+ if (ret)
goto err_destroy_encoder;
- }
+
#ifdef CONFIG_DRM_VC4_HDMI_CEC
hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
vc4, "vc4",
@@ -1342,7 +1335,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
if (ret < 0)
goto err_destroy_conn;
- cec_fill_conn_info_from_drm(&conn_info, hdmi->connector);
+ cec_fill_conn_info_from_drm(&conn_info, &hdmi->connector.base);
cec_s_conn_info(hdmi->cec_adap, &conn_info);
HDMI_WRITE(VC4_HDMI_CPU_MASK_SET, 0xffffffff);
@@ -1379,10 +1372,10 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
err_delete_cec_adap:
cec_delete_adapter(hdmi->cec_adap);
err_destroy_conn:
- vc4_hdmi_connector_destroy(hdmi->connector);
+ vc4_hdmi_connector_destroy(&hdmi->connector.base);
#endif
err_destroy_encoder:
- drm_encoder_cleanup(hdmi->encoder);
+ drm_encoder_cleanup(encoder);
err_unprepare_hsm:
clk_disable_unprepare(hdmi->hsm_clock);
pm_runtime_disable(dev);
@@ -1400,8 +1393,8 @@ static void vc4_hdmi_unbind(struct device *dev, struct device *master,
struct vc4_hdmi *hdmi = vc4->hdmi;
cec_unregister_adapter(hdmi->cec_adap);
- vc4_hdmi_connector_destroy(hdmi->connector);
- drm_encoder_cleanup(hdmi->encoder);
+ vc4_hdmi_connector_destroy(&hdmi->connector.base);
+ drm_encoder_cleanup(&hdmi->encoder.base.base);
clk_disable_unprepare(hdmi->hsm_clock);
pm_runtime_disable(dev);
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
index 5ec5d1f6b1e6..17079a39f1b1 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -8,6 +8,36 @@
#include "vc4_drv.h"
+/* VC4 HDMI encoder KMS struct */
+struct vc4_hdmi_encoder {
+ struct vc4_encoder base;
+ bool hdmi_monitor;
+ bool limited_rgb_range;
+};
+
+static inline struct vc4_hdmi_encoder *
+to_vc4_hdmi_encoder(struct drm_encoder *encoder)
+{
+ return container_of(encoder, struct vc4_hdmi_encoder, base.base);
+}
+
+/* VC4 HDMI connector KMS struct */
+struct vc4_hdmi_connector {
+ struct drm_connector base;
+
+ /* Since the connector is attached to just the one encoder,
+ * this is the reference to it so we can do the best_encoder()
+ * hook.
+ */
+ struct drm_encoder *encoder;
+};
+
+static inline struct vc4_hdmi_connector *
+to_vc4_hdmi_connector(struct drm_connector *connector)
+{
+ return container_of(connector, struct vc4_hdmi_connector, base);
+}
+
/* HDMI audio information */
struct vc4_hdmi_audio {
struct snd_soc_card card;
@@ -25,8 +55,8 @@ struct vc4_hdmi_audio {
struct vc4_hdmi {
struct platform_device *pdev;
- struct drm_encoder *encoder;
- struct drm_connector *connector;
+ struct vc4_hdmi_encoder encoder;
+ struct vc4_hdmi_connector connector;
struct vc4_hdmi_audio audio;
@@ -53,34 +83,4 @@ struct vc4_hdmi {
#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
-/* VC4 HDMI encoder KMS struct */
-struct vc4_hdmi_encoder {
- struct vc4_encoder base;
- bool hdmi_monitor;
- bool limited_rgb_range;
-};
-
-static inline struct vc4_hdmi_encoder *
-to_vc4_hdmi_encoder(struct drm_encoder *encoder)
-{
- return container_of(encoder, struct vc4_hdmi_encoder, base.base);
-}
-
-/* VC4 HDMI connector KMS struct */
-struct vc4_hdmi_connector {
- struct drm_connector base;
-
- /* Since the connector is attached to just the one encoder,
- * this is the reference to it so we can do the best_encoder()
- * hook.
- */
- struct drm_encoder *encoder;
-};
-
-static inline struct vc4_hdmi_connector *
-to_vc4_hdmi_connector(struct drm_connector *connector)
-{
- return container_of(connector, struct vc4_hdmi_connector, base);
-}
-
#endif /* _VC4_HDMI_H_ */
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 40/80] drm/vc4: hdmi: rework connectors and encoders
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
the vc4_hdmi driver has some custom structures to hold the data it needs to
associate with the drm_encoder and drm_connector structures.
However, it allocates them separately from the vc4_hdmi structure which
makes it more complicated than it needs to be.
Move those structures to be contained by vc4_hdmi and update the code
accordingly.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 87 ++++++++++++++++-------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 64 +++++++++++++-------------
2 files changed, 72 insertions(+), 79 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 5c4d2fee6b86..9a0612a87fb8 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -191,20 +191,15 @@ static const struct drm_connector_helper_funcs vc4_hdmi_connector_helper_funcs =
.get_modes = vc4_hdmi_connector_get_modes,
};
-static struct drm_connector *vc4_hdmi_connector_init(struct drm_device *dev,
- struct drm_encoder *encoder,
- struct i2c_adapter *ddc)
+static int vc4_hdmi_connector_init(struct drm_device *dev,
+ struct vc4_hdmi *vc4_hdmi,
+ struct i2c_adapter *ddc)
{
- struct drm_connector *connector;
- struct vc4_hdmi_connector *hdmi_connector;
+ struct vc4_hdmi_connector *hdmi_connector = &vc4_hdmi->connector;
+ struct drm_connector *connector = &hdmi_connector->base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
int ret;
- hdmi_connector = devm_kzalloc(dev->dev, sizeof(*hdmi_connector),
- GFP_KERNEL);
- if (!hdmi_connector)
- return ERR_PTR(-ENOMEM);
- connector = &hdmi_connector->base;
-
hdmi_connector->encoder = encoder;
drm_connector_init_with_ddc(dev, connector,
@@ -216,7 +211,7 @@ static struct drm_connector *vc4_hdmi_connector_init(struct drm_device *dev,
/* Create and attach TV margin props to this connector. */
ret = drm_mode_create_tv_margin_properties(dev);
if (ret)
- return ERR_PTR(ret);
+ return ret;
drm_connector_attach_tv_margin_properties(connector);
@@ -228,7 +223,7 @@ static struct drm_connector *vc4_hdmi_connector_init(struct drm_device *dev,
drm_connector_attach_encoder(connector, encoder);
- return connector;
+ return 0;
}
static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
@@ -298,21 +293,22 @@ static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
struct vc4_dev *vc4 = encoder->dev->dev_private;
struct vc4_hdmi *hdmi = vc4->hdmi;
- struct drm_connector_state *cstate = hdmi->connector->state;
+ struct drm_connector *connector = &hdmi->connector.base;
+ struct drm_connector_state *cstate = connector->state;
struct drm_crtc *crtc = encoder->crtc;
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
union hdmi_infoframe frame;
int ret;
ret = drm_hdmi_avi_infoframe_from_display_mode(&frame.avi,
- hdmi->connector, mode);
+ connector, mode);
if (ret < 0) {
DRM_ERROR("couldn't fill AVI infoframe\n");
return;
}
drm_hdmi_avi_infoframe_quant_range(&frame.avi,
- hdmi->connector, mode,
+ connector, mode,
vc4_encoder->limited_rgb_range ?
HDMI_QUANTIZATION_RANGE_LIMITED :
HDMI_QUANTIZATION_RANGE_FULL);
@@ -628,7 +624,8 @@ static const struct drm_encoder_helper_funcs vc4_hdmi_encoder_helper_funcs = {
/* HDMI audio codec callbacks */
static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
{
- struct drm_device *drm = hdmi->encoder->dev;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 hsm_clock = clk_get_rate(hdmi->hsm_clock);
unsigned long n, m;
@@ -647,7 +644,7 @@ static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
static void vc4_hdmi_set_n_cts(struct vc4_hdmi *hdmi)
{
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_crtc *crtc = encoder->crtc;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -685,7 +682,8 @@ static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_connector *connector = &hdmi->connector.base;
struct vc4_dev *vc4 = to_vc4_dev(encoder->dev);
int ret;
@@ -702,8 +700,7 @@ static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
VC4_HDMI_RAM_PACKET_ENABLE))
return -ENODEV;
- ret = snd_pcm_hw_constraint_eld(substream->runtime,
- hdmi->connector->eld);
+ ret = snd_pcm_hw_constraint_eld(substream->runtime, connector->eld);
if (ret)
return ret;
@@ -717,7 +714,7 @@ static int vc4_hdmi_audio_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
static void vc4_hdmi_audio_reset(struct vc4_hdmi *hdmi)
{
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct device *dev = &hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -751,7 +748,7 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct device *dev = &hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -824,7 +821,7 @@ static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = hdmi->encoder;
+ struct drm_encoder *encoder = &hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -868,9 +865,10 @@ static int vc4_hdmi_audio_eld_ctl_info(struct snd_kcontrol *kcontrol,
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &hdmi->connector.base;
uinfo->type = SNDRV_CTL_ELEM_TYPE_BYTES;
- uinfo->count = sizeof(hdmi->connector->eld);
+ uinfo->count = sizeof(connector->eld);
return 0;
}
@@ -880,9 +878,10 @@ static int vc4_hdmi_audio_eld_ctl_get(struct snd_kcontrol *kcontrol,
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &hdmi->connector.base;
- memcpy(ucontrol->value.bytes.data, hdmi->connector->eld,
- sizeof(hdmi->connector->eld));
+ memcpy(ucontrol->value.bytes.data, connector->eld,
+ sizeof(connector->eld));
return 0;
}
@@ -1220,7 +1219,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
struct vc4_hdmi *hdmi;
- struct vc4_hdmi_encoder *vc4_hdmi_encoder;
+ struct drm_encoder *encoder;
struct device_node *ddc_node;
u32 value;
int ret;
@@ -1229,14 +1228,10 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
if (!hdmi)
return -ENOMEM;
- vc4_hdmi_encoder = devm_kzalloc(dev, sizeof(*vc4_hdmi_encoder),
- GFP_KERNEL);
- if (!vc4_hdmi_encoder)
- return -ENOMEM;
- vc4_hdmi_encoder->base.type = VC4_ENCODER_TYPE_HDMI0;
- hdmi->encoder = &vc4_hdmi_encoder->base.base;
-
+ encoder = &hdmi->encoder.base.base;
+ hdmi->encoder.base.type = VC4_ENCODER_TYPE_HDMI0;
hdmi->pdev = pdev;
+
hdmi->hdmicore_regs = vc4_ioremap_regs(pdev, 0);
if (IS_ERR(hdmi->hdmicore_regs))
return PTR_ERR(hdmi->hdmicore_regs);
@@ -1324,15 +1319,13 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
}
pm_runtime_enable(dev);
- drm_simple_encoder_init(drm, hdmi->encoder, DRM_MODE_ENCODER_TMDS);
- drm_encoder_helper_add(hdmi->encoder, &vc4_hdmi_encoder_helper_funcs);
+ drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
+ drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
- hdmi->connector =
- vc4_hdmi_connector_init(drm, hdmi->encoder, hdmi->ddc);
- if (IS_ERR(hdmi->connector)) {
- ret = PTR_ERR(hdmi->connector);
+ ret = vc4_hdmi_connector_init(drm, hdmi, hdmi->ddc);
+ if (ret)
goto err_destroy_encoder;
- }
+
#ifdef CONFIG_DRM_VC4_HDMI_CEC
hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
vc4, "vc4",
@@ -1342,7 +1335,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
if (ret < 0)
goto err_destroy_conn;
- cec_fill_conn_info_from_drm(&conn_info, hdmi->connector);
+ cec_fill_conn_info_from_drm(&conn_info, &hdmi->connector.base);
cec_s_conn_info(hdmi->cec_adap, &conn_info);
HDMI_WRITE(VC4_HDMI_CPU_MASK_SET, 0xffffffff);
@@ -1379,10 +1372,10 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
err_delete_cec_adap:
cec_delete_adapter(hdmi->cec_adap);
err_destroy_conn:
- vc4_hdmi_connector_destroy(hdmi->connector);
+ vc4_hdmi_connector_destroy(&hdmi->connector.base);
#endif
err_destroy_encoder:
- drm_encoder_cleanup(hdmi->encoder);
+ drm_encoder_cleanup(encoder);
err_unprepare_hsm:
clk_disable_unprepare(hdmi->hsm_clock);
pm_runtime_disable(dev);
@@ -1400,8 +1393,8 @@ static void vc4_hdmi_unbind(struct device *dev, struct device *master,
struct vc4_hdmi *hdmi = vc4->hdmi;
cec_unregister_adapter(hdmi->cec_adap);
- vc4_hdmi_connector_destroy(hdmi->connector);
- drm_encoder_cleanup(hdmi->encoder);
+ vc4_hdmi_connector_destroy(&hdmi->connector.base);
+ drm_encoder_cleanup(&hdmi->encoder.base.base);
clk_disable_unprepare(hdmi->hsm_clock);
pm_runtime_disable(dev);
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
index 5ec5d1f6b1e6..17079a39f1b1 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -8,6 +8,36 @@
#include "vc4_drv.h"
+/* VC4 HDMI encoder KMS struct */
+struct vc4_hdmi_encoder {
+ struct vc4_encoder base;
+ bool hdmi_monitor;
+ bool limited_rgb_range;
+};
+
+static inline struct vc4_hdmi_encoder *
+to_vc4_hdmi_encoder(struct drm_encoder *encoder)
+{
+ return container_of(encoder, struct vc4_hdmi_encoder, base.base);
+}
+
+/* VC4 HDMI connector KMS struct */
+struct vc4_hdmi_connector {
+ struct drm_connector base;
+
+ /* Since the connector is attached to just the one encoder,
+ * this is the reference to it so we can do the best_encoder()
+ * hook.
+ */
+ struct drm_encoder *encoder;
+};
+
+static inline struct vc4_hdmi_connector *
+to_vc4_hdmi_connector(struct drm_connector *connector)
+{
+ return container_of(connector, struct vc4_hdmi_connector, base);
+}
+
/* HDMI audio information */
struct vc4_hdmi_audio {
struct snd_soc_card card;
@@ -25,8 +55,8 @@ struct vc4_hdmi_audio {
struct vc4_hdmi {
struct platform_device *pdev;
- struct drm_encoder *encoder;
- struct drm_connector *connector;
+ struct vc4_hdmi_encoder encoder;
+ struct vc4_hdmi_connector connector;
struct vc4_hdmi_audio audio;
@@ -53,34 +83,4 @@ struct vc4_hdmi {
#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
-/* VC4 HDMI encoder KMS struct */
-struct vc4_hdmi_encoder {
- struct vc4_encoder base;
- bool hdmi_monitor;
- bool limited_rgb_range;
-};
-
-static inline struct vc4_hdmi_encoder *
-to_vc4_hdmi_encoder(struct drm_encoder *encoder)
-{
- return container_of(encoder, struct vc4_hdmi_encoder, base.base);
-}
-
-/* VC4 HDMI connector KMS struct */
-struct vc4_hdmi_connector {
- struct drm_connector base;
-
- /* Since the connector is attached to just the one encoder,
- * this is the reference to it so we can do the best_encoder()
- * hook.
- */
- struct drm_encoder *encoder;
-};
-
-static inline struct vc4_hdmi_connector *
-to_vc4_hdmi_connector(struct drm_connector *connector)
-{
- return container_of(connector, struct vc4_hdmi_connector, base);
-}
-
#endif /* _VC4_HDMI_H_ */
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 41/80] drm/vc4: hdmi: Remove DDC argument to connector_init
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Now that we are passing the vc4_hdmi structure to the connector init
function, we can simply use the pointer in that structure instead of
having the pointer as an argument.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 9a0612a87fb8..1f350b068fcd 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -192,8 +192,7 @@ static const struct drm_connector_helper_funcs vc4_hdmi_connector_helper_funcs =
};
static int vc4_hdmi_connector_init(struct drm_device *dev,
- struct vc4_hdmi *vc4_hdmi,
- struct i2c_adapter *ddc)
+ struct vc4_hdmi *vc4_hdmi)
{
struct vc4_hdmi_connector *hdmi_connector = &vc4_hdmi->connector;
struct drm_connector *connector = &hdmi_connector->base;
@@ -205,7 +204,7 @@ static int vc4_hdmi_connector_init(struct drm_device *dev,
drm_connector_init_with_ddc(dev, connector,
&vc4_hdmi_connector_funcs,
DRM_MODE_CONNECTOR_HDMIA,
- ddc);
+ vc4_hdmi->ddc);
drm_connector_helper_add(connector, &vc4_hdmi_connector_helper_funcs);
/* Create and attach TV margin props to this connector. */
@@ -1322,7 +1321,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
- ret = vc4_hdmi_connector_init(drm, hdmi, hdmi->ddc);
+ ret = vc4_hdmi_connector_init(drm, hdmi);
if (ret)
goto err_destroy_encoder;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 41/80] drm/vc4: hdmi: Remove DDC argument to connector_init
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Now that we are passing the vc4_hdmi structure to the connector init
function, we can simply use the pointer in that structure instead of
having the pointer as an argument.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 9a0612a87fb8..1f350b068fcd 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -192,8 +192,7 @@ static const struct drm_connector_helper_funcs vc4_hdmi_connector_helper_funcs =
};
static int vc4_hdmi_connector_init(struct drm_device *dev,
- struct vc4_hdmi *vc4_hdmi,
- struct i2c_adapter *ddc)
+ struct vc4_hdmi *vc4_hdmi)
{
struct vc4_hdmi_connector *hdmi_connector = &vc4_hdmi->connector;
struct drm_connector *connector = &hdmi_connector->base;
@@ -205,7 +204,7 @@ static int vc4_hdmi_connector_init(struct drm_device *dev,
drm_connector_init_with_ddc(dev, connector,
&vc4_hdmi_connector_funcs,
DRM_MODE_CONNECTOR_HDMIA,
- ddc);
+ vc4_hdmi->ddc);
drm_connector_helper_add(connector, &vc4_hdmi_connector_helper_funcs);
/* Create and attach TV margin props to this connector. */
@@ -1322,7 +1321,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
- ret = vc4_hdmi_connector_init(drm, hdmi, hdmi->ddc);
+ ret = vc4_hdmi_connector_init(drm, hdmi);
if (ret)
goto err_destroy_encoder;
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 41/80] drm/vc4: hdmi: Remove DDC argument to connector_init
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Now that we are passing the vc4_hdmi structure to the connector init
function, we can simply use the pointer in that structure instead of
having the pointer as an argument.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 9a0612a87fb8..1f350b068fcd 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -192,8 +192,7 @@ static const struct drm_connector_helper_funcs vc4_hdmi_connector_helper_funcs =
};
static int vc4_hdmi_connector_init(struct drm_device *dev,
- struct vc4_hdmi *vc4_hdmi,
- struct i2c_adapter *ddc)
+ struct vc4_hdmi *vc4_hdmi)
{
struct vc4_hdmi_connector *hdmi_connector = &vc4_hdmi->connector;
struct drm_connector *connector = &hdmi_connector->base;
@@ -205,7 +204,7 @@ static int vc4_hdmi_connector_init(struct drm_device *dev,
drm_connector_init_with_ddc(dev, connector,
&vc4_hdmi_connector_funcs,
DRM_MODE_CONNECTOR_HDMIA,
- ddc);
+ vc4_hdmi->ddc);
drm_connector_helper_add(connector, &vc4_hdmi_connector_helper_funcs);
/* Create and attach TV margin props to this connector. */
@@ -1322,7 +1321,7 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
- ret = vc4_hdmi_connector_init(drm, hdmi, hdmi->ddc);
+ ret = vc4_hdmi_connector_init(drm, hdmi);
if (ret)
goto err_destroy_encoder;
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 42/80] drm/vc4: hdmi: Rename hdmi to vc4_hdmi
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The driver isn't consistent with the name given to the vc4_hdmi
structure pointer in its functions. Make sure to use a consistent name.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 283 +++++++++++++++++-----------------
1 file changed, 142 insertions(+), 141 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 1f350b068fcd..6733e4bc235b 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -109,11 +109,11 @@ static const struct debugfs_reg32 hd_regs[] = {
static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
{
struct drm_info_node *node = (struct drm_info_node *)m->private;
- struct vc4_hdmi *hdmi = node->info_ent->data;
+ struct vc4_hdmi *vc4_hdmi = node->info_ent->data;
struct drm_printer p = drm_seq_file_printer(m);
- drm_print_regset32(&p, &hdmi->hdmi_regset);
- drm_print_regset32(&p, &hdmi->hd_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hdmi_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hd_regset);
return 0;
}
@@ -291,8 +291,8 @@ static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
{
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
struct vc4_dev *vc4 = encoder->dev->dev_private;
- struct vc4_hdmi *hdmi = vc4->hdmi;
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
struct drm_connector_state *cstate = connector->state;
struct drm_crtc *crtc = encoder->crtc;
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
@@ -337,7 +337,7 @@ static void vc4_hdmi_set_audio_infoframe(struct drm_encoder *encoder)
{
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
union hdmi_infoframe frame;
int ret;
@@ -346,7 +346,7 @@ static void vc4_hdmi_set_audio_infoframe(struct drm_encoder *encoder)
frame.audio.coding_type = HDMI_AUDIO_CODING_TYPE_STREAM;
frame.audio.sample_frequency = HDMI_AUDIO_SAMPLE_FREQUENCY_STREAM;
frame.audio.sample_size = HDMI_AUDIO_SAMPLE_SIZE_STREAM;
- frame.audio.channels = hdmi->audio.channels;
+ frame.audio.channels = vc4_hdmi->audio.channels;
vc4_hdmi_write_infoframe(encoder, &frame);
}
@@ -361,7 +361,7 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
{
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
int ret;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG, 0);
@@ -370,9 +370,9 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
HD_WRITE(VC4_HD_VID_CTL,
HD_READ(VC4_HD_VID_CTL) & ~VC4_HD_VID_CTL_ENABLE);
- clk_disable_unprepare(hdmi->pixel_clock);
+ clk_disable_unprepare(vc4_hdmi->pixel_clock);
- ret = pm_runtime_put(&hdmi->pdev->dev);
+ ret = pm_runtime_put(&vc4_hdmi->pdev->dev);
if (ret < 0)
DRM_ERROR("Failed to release power domain: %d\n", ret);
}
@@ -383,7 +383,7 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
bool debug_dump_regs = false;
bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
@@ -405,13 +405,13 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
u32 csc_ctl;
int ret;
- ret = pm_runtime_get_sync(&hdmi->pdev->dev);
+ ret = pm_runtime_get_sync(&vc4_hdmi->pdev->dev);
if (ret < 0) {
DRM_ERROR("Failed to retain power domain: %d\n", ret);
return;
}
- ret = clk_set_rate(hdmi->pixel_clock,
+ ret = clk_set_rate(vc4_hdmi->pixel_clock,
mode->clock * 1000 *
((mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1));
if (ret) {
@@ -419,7 +419,7 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
return;
}
- ret = clk_prepare_enable(hdmi->pixel_clock);
+ ret = clk_prepare_enable(vc4_hdmi->pixel_clock);
if (ret) {
DRM_ERROR("Failed to turn on pixel clock: %d\n", ret);
return;
@@ -439,11 +439,11 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
HDMI_WRITE(VC4_HDMI_TX_PHY_RESET_CTL, 0);
if (debug_dump_regs) {
- struct drm_printer p = drm_info_printer(&hdmi->pdev->dev);
+ struct drm_printer p = drm_info_printer(&vc4_hdmi->pdev->dev);
- dev_info(&hdmi->pdev->dev, "HDMI regs before:\n");
- drm_print_regset32(&p, &hdmi->hdmi_regset);
- drm_print_regset32(&p, &hdmi->hd_regset);
+ dev_info(&vc4_hdmi->pdev->dev, "HDMI regs before:\n");
+ drm_print_regset32(&p, &vc4_hdmi->hdmi_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hd_regset);
}
HD_WRITE(VC4_HD_VID_CTL, 0);
@@ -518,11 +518,11 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
HDMI_WRITE(VC4_HDMI_FIFO_CTL, VC4_HDMI_FIFO_CTL_MASTER_SLAVE_N);
if (debug_dump_regs) {
- struct drm_printer p = drm_info_printer(&hdmi->pdev->dev);
+ struct drm_printer p = drm_info_printer(&vc4_hdmi->pdev->dev);
- dev_info(&hdmi->pdev->dev, "HDMI regs after:\n");
- drm_print_regset32(&p, &hdmi->hdmi_regset);
- drm_print_regset32(&p, &hdmi->hd_regset);
+ dev_info(&vc4_hdmi->pdev->dev, "HDMI regs after:\n");
+ drm_print_regset32(&p, &vc4_hdmi->hdmi_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hd_regset);
}
HD_WRITE(VC4_HD_VID_CTL,
@@ -621,15 +621,15 @@ static const struct drm_encoder_helper_funcs vc4_hdmi_encoder_helper_funcs = {
};
/* HDMI audio codec callbacks */
-static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
+static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
- u32 hsm_clock = clk_get_rate(hdmi->hsm_clock);
+ u32 hsm_clock = clk_get_rate(vc4_hdmi->hsm_clock);
unsigned long n, m;
- rational_best_approximation(hsm_clock, hdmi->audio.samplerate,
+ rational_best_approximation(hsm_clock, vc4_hdmi->audio.samplerate,
VC4_HD_MAI_SMP_N_MASK >>
VC4_HD_MAI_SMP_N_SHIFT,
(VC4_HD_MAI_SMP_M_MASK >>
@@ -641,14 +641,14 @@ static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
VC4_SET_FIELD(m - 1, VC4_HD_MAI_SMP_M));
}
-static void vc4_hdmi_set_n_cts(struct vc4_hdmi *hdmi)
+static void vc4_hdmi_set_n_cts(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_crtc *crtc = encoder->crtc;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
- u32 samplerate = hdmi->audio.samplerate;
+ u32 samplerate = vc4_hdmi->audio.samplerate;
u32 n, cts;
u64 tmp;
@@ -680,16 +680,16 @@ static inline struct vc4_hdmi *dai_to_hdmi(struct snd_soc_dai *dai)
static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
struct vc4_dev *vc4 = to_vc4_dev(encoder->dev);
int ret;
- if (hdmi->audio.substream && hdmi->audio.substream != substream)
+ if (vc4_hdmi->audio.substream && vc4_hdmi->audio.substream != substream)
return -EINVAL;
- hdmi->audio.substream = substream;
+ vc4_hdmi->audio.substream = substream;
/*
* If the HDMI encoder hasn't probed, or the encoder is
@@ -711,11 +711,11 @@ static int vc4_hdmi_audio_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
return 0;
}
-static void vc4_hdmi_audio_reset(struct vc4_hdmi *hdmi)
+static void vc4_hdmi_audio_reset(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
- struct device *dev = &hdmi->pdev->dev;
+ struct device *dev = &vc4_hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
int ret;
@@ -731,14 +731,14 @@ static void vc4_hdmi_audio_reset(struct vc4_hdmi *hdmi)
static void vc4_hdmi_audio_shutdown(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
- if (substream != hdmi->audio.substream)
+ if (substream != vc4_hdmi->audio.substream)
return;
- vc4_hdmi_audio_reset(hdmi);
+ vc4_hdmi_audio_reset(vc4_hdmi);
- hdmi->audio.substream = NULL;
+ vc4_hdmi->audio.substream = NULL;
}
/* HDMI audio codec callbacks */
@@ -746,23 +746,23 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
- struct device *dev = &hdmi->pdev->dev;
+ struct device *dev = &vc4_hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 audio_packet_config, channel_mask;
u32 channel_map, i;
- if (substream != hdmi->audio.substream)
+ if (substream != vc4_hdmi->audio.substream)
return -EINVAL;
dev_dbg(dev, "%s: %u Hz, %d bit, %d channels\n", __func__,
params_rate(params), params_width(params),
params_channels(params));
- hdmi->audio.channels = params_channels(params);
- hdmi->audio.samplerate = params_rate(params);
+ vc4_hdmi->audio.channels = params_channels(params);
+ vc4_hdmi->audio.samplerate = params_rate(params);
HD_WRITE(VC4_HD_MAI_CTL,
VC4_HD_MAI_CTL_RESET |
@@ -771,23 +771,23 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
VC4_HD_MAI_CTL_ERRORE |
VC4_HD_MAI_CTL_ERRORF);
- vc4_hdmi_audio_set_mai_clock(hdmi);
+ vc4_hdmi_audio_set_mai_clock(vc4_hdmi);
audio_packet_config =
VC4_HDMI_AUDIO_PACKET_ZERO_DATA_ON_SAMPLE_FLAT |
VC4_HDMI_AUDIO_PACKET_ZERO_DATA_ON_INACTIVE_CHANNELS |
VC4_SET_FIELD(0xf, VC4_HDMI_AUDIO_PACKET_B_FRAME_IDENTIFIER);
- channel_mask = GENMASK(hdmi->audio.channels - 1, 0);
+ channel_mask = GENMASK(vc4_hdmi->audio.channels - 1, 0);
audio_packet_config |= VC4_SET_FIELD(channel_mask,
VC4_HDMI_AUDIO_PACKET_CEA_MASK);
/* Set the MAI threshold. This logic mimics the firmware's. */
- if (hdmi->audio.samplerate > 96000) {
+ if (vc4_hdmi->audio.samplerate > 96000) {
HD_WRITE(VC4_HD_MAI_THR,
VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQHIGH) |
VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQLOW));
- } else if (hdmi->audio.samplerate > 48000) {
+ } else if (vc4_hdmi->audio.samplerate > 48000) {
HD_WRITE(VC4_HD_MAI_THR,
VC4_SET_FIELD(0x14, VC4_HD_MAI_THR_DREQHIGH) |
VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQLOW));
@@ -811,7 +811,7 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
HDMI_WRITE(VC4_HDMI_MAI_CHANNEL_MAP, channel_map);
HDMI_WRITE(VC4_HDMI_AUDIO_PACKET_CONFIG, audio_packet_config);
- vc4_hdmi_set_n_cts(hdmi);
+ vc4_hdmi_set_n_cts(vc4_hdmi);
return 0;
}
@@ -819,8 +819,8 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -831,7 +831,7 @@ static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
HDMI_READ(VC4_HDMI_TX_PHY_CTL0) &
~VC4_HDMI_TX_PHY_RNG_PWRDN);
HD_WRITE(VC4_HD_MAI_CTL,
- VC4_SET_FIELD(hdmi->audio.channels,
+ VC4_SET_FIELD(vc4_hdmi->audio.channels,
VC4_HD_MAI_CTL_CHNUM) |
VC4_HD_MAI_CTL_ENABLE);
break;
@@ -863,8 +863,8 @@ static int vc4_hdmi_audio_eld_ctl_info(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_info *uinfo)
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
- struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
uinfo->type = SNDRV_CTL_ELEM_TYPE_BYTES;
uinfo->count = sizeof(connector->eld);
@@ -876,8 +876,8 @@ static int vc4_hdmi_audio_eld_ctl_get(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
- struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
memcpy(ucontrol->value.bytes.data, connector->eld,
sizeof(connector->eld));
@@ -945,9 +945,9 @@ static const struct snd_soc_component_driver vc4_hdmi_audio_cpu_dai_comp = {
static int vc4_hdmi_audio_cpu_dai_probe(struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
- snd_soc_dai_init_dma_data(dai, &hdmi->audio.dma_data, NULL);
+ snd_soc_dai_init_dma_data(dai, &vc4_hdmi->audio.dma_data, NULL);
return 0;
}
@@ -973,11 +973,11 @@ static const struct snd_dmaengine_pcm_config pcm_conf = {
.prepare_slave_config = snd_dmaengine_pcm_prepare_slave_config,
};
-static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
+static int vc4_hdmi_audio_init(struct vc4_hdmi *vc4_hdmi)
{
- struct snd_soc_dai_link *dai_link = &hdmi->audio.link;
- struct snd_soc_card *card = &hdmi->audio.card;
- struct device *dev = &hdmi->pdev->dev;
+ struct snd_soc_dai_link *dai_link = &vc4_hdmi->audio.link;
+ struct snd_soc_card *card = &vc4_hdmi->audio.card;
+ struct device *dev = &vc4_hdmi->pdev->dev;
const __be32 *addr;
int ret;
@@ -995,9 +995,9 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
* This VC/MMU should probably be exposed to avoid this kind of hacks.
*/
addr = of_get_address(dev->of_node, 1, NULL, NULL);
- hdmi->audio.dma_data.addr = be32_to_cpup(addr) + VC4_HD_MAI_DATA;
- hdmi->audio.dma_data.addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- hdmi->audio.dma_data.maxburst = 2;
+ vc4_hdmi->audio.dma_data.addr = be32_to_cpup(addr) + VC4_HD_MAI_DATA;
+ vc4_hdmi->audio.dma_data.addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ vc4_hdmi->audio.dma_data.maxburst = 2;
ret = devm_snd_dmaengine_pcm_register(dev, &pcm_conf, 0);
if (ret) {
@@ -1020,9 +1020,9 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
return ret;
}
- dai_link->cpus = &hdmi->audio.cpu;
- dai_link->codecs = &hdmi->audio.codec;
- dai_link->platforms = &hdmi->audio.platform;
+ dai_link->cpus = &vc4_hdmi->audio.cpu;
+ dai_link->codecs = &vc4_hdmi->audio.codec;
+ dai_link->platforms = &vc4_hdmi->audio.platform;
dai_link->num_cpus = 1;
dai_link->num_codecs = 1;
@@ -1047,7 +1047,7 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
* now stored in card->drvdata and should be retrieved with
* snd_soc_card_get_drvdata() if needed.
*/
- snd_soc_card_set_drvdata(card, hdmi);
+ snd_soc_card_set_drvdata(card, vc4_hdmi);
ret = devm_snd_soc_register_card(dev, card);
if (ret)
dev_err(dev, "Could not register sound card: %d\n", ret);
@@ -1060,20 +1060,21 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
static irqreturn_t vc4_cec_irq_handler_thread(int irq, void *priv)
{
struct vc4_dev *vc4 = priv;
- struct vc4_hdmi *hdmi = vc4->hdmi;
-
- if (hdmi->cec_irq_was_rx) {
- if (hdmi->cec_rx_msg.len)
- cec_received_msg(hdmi->cec_adap, &hdmi->cec_rx_msg);
- } else if (hdmi->cec_tx_ok) {
- cec_transmit_done(hdmi->cec_adap, CEC_TX_STATUS_OK,
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+
+ if (vc4_hdmi->cec_irq_was_rx) {
+ if (vc4_hdmi->cec_rx_msg.len)
+ cec_received_msg(vc4_hdmi->cec_adap,
+ &vc4_hdmi->cec_rx_msg);
+ } else if (vc4_hdmi->cec_tx_ok) {
+ cec_transmit_done(vc4_hdmi->cec_adap, CEC_TX_STATUS_OK,
0, 0, 0, 0);
} else {
/*
* This CEC implementation makes 1 retry, so if we
* get a NACK, then that means it made 2 attempts.
*/
- cec_transmit_done(hdmi->cec_adap, CEC_TX_STATUS_NACK,
+ cec_transmit_done(vc4_hdmi->cec_adap, CEC_TX_STATUS_NACK,
0, 2, 0, 0);
}
return IRQ_HANDLED;
@@ -1099,23 +1100,23 @@ static void vc4_cec_read_msg(struct vc4_dev *vc4, u32 cntrl1)
static irqreturn_t vc4_cec_irq_handler(int irq, void *priv)
{
struct vc4_dev *vc4 = priv;
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 stat = HDMI_READ(VC4_HDMI_CPU_STATUS);
u32 cntrl1, cntrl5;
if (!(stat & VC4_HDMI_CPU_CEC))
return IRQ_NONE;
- hdmi->cec_rx_msg.len = 0;
+ vc4_hdmi->cec_rx_msg.len = 0;
cntrl1 = HDMI_READ(VC4_HDMI_CEC_CNTRL_1);
cntrl5 = HDMI_READ(VC4_HDMI_CEC_CNTRL_5);
- hdmi->cec_irq_was_rx = cntrl5 & VC4_HDMI_CEC_RX_CEC_INT;
- if (hdmi->cec_irq_was_rx) {
+ vc4_hdmi->cec_irq_was_rx = cntrl5 & VC4_HDMI_CEC_RX_CEC_INT;
+ if (vc4_hdmi->cec_irq_was_rx) {
vc4_cec_read_msg(vc4, cntrl1);
cntrl1 |= VC4_HDMI_CEC_CLEAR_RECEIVE_OFF;
HDMI_WRITE(VC4_HDMI_CEC_CNTRL_1, cntrl1);
cntrl1 &= ~VC4_HDMI_CEC_CLEAR_RECEIVE_OFF;
} else {
- hdmi->cec_tx_ok = cntrl1 & VC4_HDMI_CEC_TX_STATUS_GOOD;
+ vc4_hdmi->cec_tx_ok = cntrl1 & VC4_HDMI_CEC_TX_STATUS_GOOD;
cntrl1 &= ~VC4_HDMI_CEC_START_XMIT_BEGIN;
}
HDMI_WRITE(VC4_HDMI_CEC_CNTRL_1, cntrl1);
@@ -1217,46 +1218,46 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
struct platform_device *pdev = to_platform_device(dev);
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *hdmi;
+ struct vc4_hdmi *vc4_hdmi;
struct drm_encoder *encoder;
struct device_node *ddc_node;
u32 value;
int ret;
- hdmi = devm_kzalloc(dev, sizeof(*hdmi), GFP_KERNEL);
- if (!hdmi)
+ vc4_hdmi = devm_kzalloc(dev, sizeof(*vc4_hdmi), GFP_KERNEL);
+ if (!vc4_hdmi)
return -ENOMEM;
- encoder = &hdmi->encoder.base.base;
- hdmi->encoder.base.type = VC4_ENCODER_TYPE_HDMI0;
- hdmi->pdev = pdev;
+ encoder = &vc4_hdmi->encoder.base.base;
+ vc4_hdmi->encoder.base.type = VC4_ENCODER_TYPE_HDMI0;
+ vc4_hdmi->pdev = pdev;
- hdmi->hdmicore_regs = vc4_ioremap_regs(pdev, 0);
- if (IS_ERR(hdmi->hdmicore_regs))
- return PTR_ERR(hdmi->hdmicore_regs);
+ vc4_hdmi->hdmicore_regs = vc4_ioremap_regs(pdev, 0);
+ if (IS_ERR(vc4_hdmi->hdmicore_regs))
+ return PTR_ERR(vc4_hdmi->hdmicore_regs);
- hdmi->hd_regs = vc4_ioremap_regs(pdev, 1);
- if (IS_ERR(hdmi->hd_regs))
- return PTR_ERR(hdmi->hd_regs);
+ vc4_hdmi->hd_regs = vc4_ioremap_regs(pdev, 1);
+ if (IS_ERR(vc4_hdmi->hd_regs))
+ return PTR_ERR(vc4_hdmi->hd_regs);
- hdmi->hdmi_regset.base = hdmi->hdmicore_regs;
- hdmi->hdmi_regset.regs = hdmi_regs;
- hdmi->hdmi_regset.nregs = ARRAY_SIZE(hdmi_regs);
- hdmi->hd_regset.base = hdmi->hd_regs;
- hdmi->hd_regset.regs = hd_regs;
- hdmi->hd_regset.nregs = ARRAY_SIZE(hd_regs);
+ vc4_hdmi->hdmi_regset.base = vc4_hdmi->hdmicore_regs;
+ vc4_hdmi->hdmi_regset.regs = hdmi_regs;
+ vc4_hdmi->hdmi_regset.nregs = ARRAY_SIZE(hdmi_regs);
+ vc4_hdmi->hd_regset.base = vc4_hdmi->hd_regs;
+ vc4_hdmi->hd_regset.regs = hd_regs;
+ vc4_hdmi->hd_regset.nregs = ARRAY_SIZE(hd_regs);
- hdmi->pixel_clock = devm_clk_get(dev, "pixel");
- if (IS_ERR(hdmi->pixel_clock)) {
- ret = PTR_ERR(hdmi->pixel_clock);
+ vc4_hdmi->pixel_clock = devm_clk_get(dev, "pixel");
+ if (IS_ERR(vc4_hdmi->pixel_clock)) {
+ ret = PTR_ERR(vc4_hdmi->pixel_clock);
if (ret != -EPROBE_DEFER)
DRM_ERROR("Failed to get pixel clock\n");
return ret;
}
- hdmi->hsm_clock = devm_clk_get(dev, "hdmi");
- if (IS_ERR(hdmi->hsm_clock)) {
+ vc4_hdmi->hsm_clock = devm_clk_get(dev, "hdmi");
+ if (IS_ERR(vc4_hdmi->hsm_clock)) {
DRM_ERROR("Failed to get HDMI state machine clock\n");
- return PTR_ERR(hdmi->hsm_clock);
+ return PTR_ERR(vc4_hdmi->hsm_clock);
}
ddc_node = of_parse_phandle(dev->of_node, "ddc", 0);
@@ -1265,9 +1266,9 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
return -ENODEV;
}
- hdmi->ddc = of_find_i2c_adapter_by_node(ddc_node);
+ vc4_hdmi->ddc = of_find_i2c_adapter_by_node(ddc_node);
of_node_put(ddc_node);
- if (!hdmi->ddc) {
+ if (!vc4_hdmi->ddc) {
DRM_DEBUG("Failed to get ddc i2c adapter by node\n");
return -EPROBE_DEFER;
}
@@ -1276,13 +1277,13 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
* needs to be a bit higher than the pixel clock rate
* (generally 148.5Mhz).
*/
- ret = clk_set_rate(hdmi->hsm_clock, HSM_CLOCK_FREQ);
+ ret = clk_set_rate(vc4_hdmi->hsm_clock, HSM_CLOCK_FREQ);
if (ret) {
DRM_ERROR("Failed to set HSM clock rate: %d\n", ret);
goto err_put_i2c;
}
- ret = clk_prepare_enable(hdmi->hsm_clock);
+ ret = clk_prepare_enable(vc4_hdmi->hsm_clock);
if (ret) {
DRM_ERROR("Failed to turn on HDMI state machine clock: %d\n",
ret);
@@ -1295,18 +1296,18 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
if (of_find_property(dev->of_node, "hpd-gpios", &value)) {
enum of_gpio_flags hpd_gpio_flags;
- hdmi->hpd_gpio = of_get_named_gpio_flags(dev->of_node,
- "hpd-gpios", 0,
- &hpd_gpio_flags);
- if (hdmi->hpd_gpio < 0) {
- ret = hdmi->hpd_gpio;
+ vc4_hdmi->hpd_gpio = of_get_named_gpio_flags(dev->of_node,
+ "hpd-gpios", 0,
+ &hpd_gpio_flags);
+ if (vc4_hdmi->hpd_gpio < 0) {
+ ret = vc4_hdmi->hpd_gpio;
goto err_unprepare_hsm;
}
- hdmi->hpd_active_low = hpd_gpio_flags & OF_GPIO_ACTIVE_LOW;
+ vc4_hdmi->hpd_active_low = hpd_gpio_flags & OF_GPIO_ACTIVE_LOW;
}
- vc4->hdmi = hdmi;
+ vc4->hdmi = vc4_hdmi;
/* HDMI core must be enabled. */
if (!(HD_READ(VC4_HD_M_CTL) & VC4_HD_M_ENABLE)) {
@@ -1321,21 +1322,21 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
- ret = vc4_hdmi_connector_init(drm, hdmi);
+ ret = vc4_hdmi_connector_init(drm, vc4_hdmi);
if (ret)
goto err_destroy_encoder;
#ifdef CONFIG_DRM_VC4_HDMI_CEC
- hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
- vc4, "vc4",
- CEC_CAP_DEFAULTS |
- CEC_CAP_CONNECTOR_INFO, 1);
- ret = PTR_ERR_OR_ZERO(hdmi->cec_adap);
+ vc4_hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
+ vc4, "vc4",
+ CEC_CAP_DEFAULTS |
+ CEC_CAP_CONNECTOR_INFO, 1);
+ ret = PTR_ERR_OR_ZERO(vc4_hdmi->cec_adap);
if (ret < 0)
goto err_destroy_conn;
- cec_fill_conn_info_from_drm(&conn_info, &hdmi->connector.base);
- cec_s_conn_info(hdmi->cec_adap, &conn_info);
+ cec_fill_conn_info_from_drm(&conn_info, &vc4_hdmi->connector.base);
+ cec_s_conn_info(vc4_hdmi->cec_adap, &conn_info);
HDMI_WRITE(VC4_HDMI_CPU_MASK_SET, 0xffffffff);
value = HDMI_READ(VC4_HDMI_CEC_CNTRL_1);
@@ -1354,32 +1355,32 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
"vc4 hdmi cec", vc4);
if (ret)
goto err_delete_cec_adap;
- ret = cec_register_adapter(hdmi->cec_adap, dev);
+ ret = cec_register_adapter(vc4_hdmi->cec_adap, dev);
if (ret < 0)
goto err_delete_cec_adap;
#endif
- ret = vc4_hdmi_audio_init(hdmi);
+ ret = vc4_hdmi_audio_init(vc4_hdmi);
if (ret)
goto err_destroy_encoder;
- vc4_debugfs_add_file(drm, "hdmi_regs", vc4_hdmi_debugfs_regs, hdmi);
+ vc4_debugfs_add_file(drm, "hdmi_regs", vc4_hdmi_debugfs_regs, vc4_hdmi);
return 0;
#ifdef CONFIG_DRM_VC4_HDMI_CEC
err_delete_cec_adap:
- cec_delete_adapter(hdmi->cec_adap);
+ cec_delete_adapter(vc4_hdmi->cec_adap);
err_destroy_conn:
- vc4_hdmi_connector_destroy(&hdmi->connector.base);
+ vc4_hdmi_connector_destroy(&vc4_hdmi->connector.base);
#endif
err_destroy_encoder:
drm_encoder_cleanup(encoder);
err_unprepare_hsm:
- clk_disable_unprepare(hdmi->hsm_clock);
+ clk_disable_unprepare(vc4_hdmi->hsm_clock);
pm_runtime_disable(dev);
err_put_i2c:
- put_device(&hdmi->ddc->dev);
+ put_device(&vc4_hdmi->ddc->dev);
return ret;
}
@@ -1389,16 +1390,16 @@ static void vc4_hdmi_unbind(struct device *dev, struct device *master,
{
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
- cec_unregister_adapter(hdmi->cec_adap);
- vc4_hdmi_connector_destroy(&hdmi->connector.base);
- drm_encoder_cleanup(&hdmi->encoder.base.base);
+ cec_unregister_adapter(vc4_hdmi->cec_adap);
+ vc4_hdmi_connector_destroy(&vc4_hdmi->connector.base);
+ drm_encoder_cleanup(&vc4_hdmi->encoder.base.base);
- clk_disable_unprepare(hdmi->hsm_clock);
+ clk_disable_unprepare(vc4_hdmi->hsm_clock);
pm_runtime_disable(dev);
- put_device(&hdmi->ddc->dev);
+ put_device(&vc4_hdmi->ddc->dev);
vc4->hdmi = NULL;
}
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 42/80] drm/vc4: hdmi: Rename hdmi to vc4_hdmi
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The driver isn't consistent with the name given to the vc4_hdmi
structure pointer in its functions. Make sure to use a consistent name.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 283 +++++++++++++++++-----------------
1 file changed, 142 insertions(+), 141 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 1f350b068fcd..6733e4bc235b 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -109,11 +109,11 @@ static const struct debugfs_reg32 hd_regs[] = {
static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
{
struct drm_info_node *node = (struct drm_info_node *)m->private;
- struct vc4_hdmi *hdmi = node->info_ent->data;
+ struct vc4_hdmi *vc4_hdmi = node->info_ent->data;
struct drm_printer p = drm_seq_file_printer(m);
- drm_print_regset32(&p, &hdmi->hdmi_regset);
- drm_print_regset32(&p, &hdmi->hd_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hdmi_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hd_regset);
return 0;
}
@@ -291,8 +291,8 @@ static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
{
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
struct vc4_dev *vc4 = encoder->dev->dev_private;
- struct vc4_hdmi *hdmi = vc4->hdmi;
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
struct drm_connector_state *cstate = connector->state;
struct drm_crtc *crtc = encoder->crtc;
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
@@ -337,7 +337,7 @@ static void vc4_hdmi_set_audio_infoframe(struct drm_encoder *encoder)
{
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
union hdmi_infoframe frame;
int ret;
@@ -346,7 +346,7 @@ static void vc4_hdmi_set_audio_infoframe(struct drm_encoder *encoder)
frame.audio.coding_type = HDMI_AUDIO_CODING_TYPE_STREAM;
frame.audio.sample_frequency = HDMI_AUDIO_SAMPLE_FREQUENCY_STREAM;
frame.audio.sample_size = HDMI_AUDIO_SAMPLE_SIZE_STREAM;
- frame.audio.channels = hdmi->audio.channels;
+ frame.audio.channels = vc4_hdmi->audio.channels;
vc4_hdmi_write_infoframe(encoder, &frame);
}
@@ -361,7 +361,7 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
{
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
int ret;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG, 0);
@@ -370,9 +370,9 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
HD_WRITE(VC4_HD_VID_CTL,
HD_READ(VC4_HD_VID_CTL) & ~VC4_HD_VID_CTL_ENABLE);
- clk_disable_unprepare(hdmi->pixel_clock);
+ clk_disable_unprepare(vc4_hdmi->pixel_clock);
- ret = pm_runtime_put(&hdmi->pdev->dev);
+ ret = pm_runtime_put(&vc4_hdmi->pdev->dev);
if (ret < 0)
DRM_ERROR("Failed to release power domain: %d\n", ret);
}
@@ -383,7 +383,7 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
bool debug_dump_regs = false;
bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
@@ -405,13 +405,13 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
u32 csc_ctl;
int ret;
- ret = pm_runtime_get_sync(&hdmi->pdev->dev);
+ ret = pm_runtime_get_sync(&vc4_hdmi->pdev->dev);
if (ret < 0) {
DRM_ERROR("Failed to retain power domain: %d\n", ret);
return;
}
- ret = clk_set_rate(hdmi->pixel_clock,
+ ret = clk_set_rate(vc4_hdmi->pixel_clock,
mode->clock * 1000 *
((mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1));
if (ret) {
@@ -419,7 +419,7 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
return;
}
- ret = clk_prepare_enable(hdmi->pixel_clock);
+ ret = clk_prepare_enable(vc4_hdmi->pixel_clock);
if (ret) {
DRM_ERROR("Failed to turn on pixel clock: %d\n", ret);
return;
@@ -439,11 +439,11 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
HDMI_WRITE(VC4_HDMI_TX_PHY_RESET_CTL, 0);
if (debug_dump_regs) {
- struct drm_printer p = drm_info_printer(&hdmi->pdev->dev);
+ struct drm_printer p = drm_info_printer(&vc4_hdmi->pdev->dev);
- dev_info(&hdmi->pdev->dev, "HDMI regs before:\n");
- drm_print_regset32(&p, &hdmi->hdmi_regset);
- drm_print_regset32(&p, &hdmi->hd_regset);
+ dev_info(&vc4_hdmi->pdev->dev, "HDMI regs before:\n");
+ drm_print_regset32(&p, &vc4_hdmi->hdmi_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hd_regset);
}
HD_WRITE(VC4_HD_VID_CTL, 0);
@@ -518,11 +518,11 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
HDMI_WRITE(VC4_HDMI_FIFO_CTL, VC4_HDMI_FIFO_CTL_MASTER_SLAVE_N);
if (debug_dump_regs) {
- struct drm_printer p = drm_info_printer(&hdmi->pdev->dev);
+ struct drm_printer p = drm_info_printer(&vc4_hdmi->pdev->dev);
- dev_info(&hdmi->pdev->dev, "HDMI regs after:\n");
- drm_print_regset32(&p, &hdmi->hdmi_regset);
- drm_print_regset32(&p, &hdmi->hd_regset);
+ dev_info(&vc4_hdmi->pdev->dev, "HDMI regs after:\n");
+ drm_print_regset32(&p, &vc4_hdmi->hdmi_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hd_regset);
}
HD_WRITE(VC4_HD_VID_CTL,
@@ -621,15 +621,15 @@ static const struct drm_encoder_helper_funcs vc4_hdmi_encoder_helper_funcs = {
};
/* HDMI audio codec callbacks */
-static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
+static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
- u32 hsm_clock = clk_get_rate(hdmi->hsm_clock);
+ u32 hsm_clock = clk_get_rate(vc4_hdmi->hsm_clock);
unsigned long n, m;
- rational_best_approximation(hsm_clock, hdmi->audio.samplerate,
+ rational_best_approximation(hsm_clock, vc4_hdmi->audio.samplerate,
VC4_HD_MAI_SMP_N_MASK >>
VC4_HD_MAI_SMP_N_SHIFT,
(VC4_HD_MAI_SMP_M_MASK >>
@@ -641,14 +641,14 @@ static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
VC4_SET_FIELD(m - 1, VC4_HD_MAI_SMP_M));
}
-static void vc4_hdmi_set_n_cts(struct vc4_hdmi *hdmi)
+static void vc4_hdmi_set_n_cts(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_crtc *crtc = encoder->crtc;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
- u32 samplerate = hdmi->audio.samplerate;
+ u32 samplerate = vc4_hdmi->audio.samplerate;
u32 n, cts;
u64 tmp;
@@ -680,16 +680,16 @@ static inline struct vc4_hdmi *dai_to_hdmi(struct snd_soc_dai *dai)
static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
struct vc4_dev *vc4 = to_vc4_dev(encoder->dev);
int ret;
- if (hdmi->audio.substream && hdmi->audio.substream != substream)
+ if (vc4_hdmi->audio.substream && vc4_hdmi->audio.substream != substream)
return -EINVAL;
- hdmi->audio.substream = substream;
+ vc4_hdmi->audio.substream = substream;
/*
* If the HDMI encoder hasn't probed, or the encoder is
@@ -711,11 +711,11 @@ static int vc4_hdmi_audio_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
return 0;
}
-static void vc4_hdmi_audio_reset(struct vc4_hdmi *hdmi)
+static void vc4_hdmi_audio_reset(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
- struct device *dev = &hdmi->pdev->dev;
+ struct device *dev = &vc4_hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
int ret;
@@ -731,14 +731,14 @@ static void vc4_hdmi_audio_reset(struct vc4_hdmi *hdmi)
static void vc4_hdmi_audio_shutdown(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
- if (substream != hdmi->audio.substream)
+ if (substream != vc4_hdmi->audio.substream)
return;
- vc4_hdmi_audio_reset(hdmi);
+ vc4_hdmi_audio_reset(vc4_hdmi);
- hdmi->audio.substream = NULL;
+ vc4_hdmi->audio.substream = NULL;
}
/* HDMI audio codec callbacks */
@@ -746,23 +746,23 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
- struct device *dev = &hdmi->pdev->dev;
+ struct device *dev = &vc4_hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 audio_packet_config, channel_mask;
u32 channel_map, i;
- if (substream != hdmi->audio.substream)
+ if (substream != vc4_hdmi->audio.substream)
return -EINVAL;
dev_dbg(dev, "%s: %u Hz, %d bit, %d channels\n", __func__,
params_rate(params), params_width(params),
params_channels(params));
- hdmi->audio.channels = params_channels(params);
- hdmi->audio.samplerate = params_rate(params);
+ vc4_hdmi->audio.channels = params_channels(params);
+ vc4_hdmi->audio.samplerate = params_rate(params);
HD_WRITE(VC4_HD_MAI_CTL,
VC4_HD_MAI_CTL_RESET |
@@ -771,23 +771,23 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
VC4_HD_MAI_CTL_ERRORE |
VC4_HD_MAI_CTL_ERRORF);
- vc4_hdmi_audio_set_mai_clock(hdmi);
+ vc4_hdmi_audio_set_mai_clock(vc4_hdmi);
audio_packet_config =
VC4_HDMI_AUDIO_PACKET_ZERO_DATA_ON_SAMPLE_FLAT |
VC4_HDMI_AUDIO_PACKET_ZERO_DATA_ON_INACTIVE_CHANNELS |
VC4_SET_FIELD(0xf, VC4_HDMI_AUDIO_PACKET_B_FRAME_IDENTIFIER);
- channel_mask = GENMASK(hdmi->audio.channels - 1, 0);
+ channel_mask = GENMASK(vc4_hdmi->audio.channels - 1, 0);
audio_packet_config |= VC4_SET_FIELD(channel_mask,
VC4_HDMI_AUDIO_PACKET_CEA_MASK);
/* Set the MAI threshold. This logic mimics the firmware's. */
- if (hdmi->audio.samplerate > 96000) {
+ if (vc4_hdmi->audio.samplerate > 96000) {
HD_WRITE(VC4_HD_MAI_THR,
VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQHIGH) |
VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQLOW));
- } else if (hdmi->audio.samplerate > 48000) {
+ } else if (vc4_hdmi->audio.samplerate > 48000) {
HD_WRITE(VC4_HD_MAI_THR,
VC4_SET_FIELD(0x14, VC4_HD_MAI_THR_DREQHIGH) |
VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQLOW));
@@ -811,7 +811,7 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
HDMI_WRITE(VC4_HDMI_MAI_CHANNEL_MAP, channel_map);
HDMI_WRITE(VC4_HDMI_AUDIO_PACKET_CONFIG, audio_packet_config);
- vc4_hdmi_set_n_cts(hdmi);
+ vc4_hdmi_set_n_cts(vc4_hdmi);
return 0;
}
@@ -819,8 +819,8 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -831,7 +831,7 @@ static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
HDMI_READ(VC4_HDMI_TX_PHY_CTL0) &
~VC4_HDMI_TX_PHY_RNG_PWRDN);
HD_WRITE(VC4_HD_MAI_CTL,
- VC4_SET_FIELD(hdmi->audio.channels,
+ VC4_SET_FIELD(vc4_hdmi->audio.channels,
VC4_HD_MAI_CTL_CHNUM) |
VC4_HD_MAI_CTL_ENABLE);
break;
@@ -863,8 +863,8 @@ static int vc4_hdmi_audio_eld_ctl_info(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_info *uinfo)
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
- struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
uinfo->type = SNDRV_CTL_ELEM_TYPE_BYTES;
uinfo->count = sizeof(connector->eld);
@@ -876,8 +876,8 @@ static int vc4_hdmi_audio_eld_ctl_get(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
- struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
memcpy(ucontrol->value.bytes.data, connector->eld,
sizeof(connector->eld));
@@ -945,9 +945,9 @@ static const struct snd_soc_component_driver vc4_hdmi_audio_cpu_dai_comp = {
static int vc4_hdmi_audio_cpu_dai_probe(struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
- snd_soc_dai_init_dma_data(dai, &hdmi->audio.dma_data, NULL);
+ snd_soc_dai_init_dma_data(dai, &vc4_hdmi->audio.dma_data, NULL);
return 0;
}
@@ -973,11 +973,11 @@ static const struct snd_dmaengine_pcm_config pcm_conf = {
.prepare_slave_config = snd_dmaengine_pcm_prepare_slave_config,
};
-static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
+static int vc4_hdmi_audio_init(struct vc4_hdmi *vc4_hdmi)
{
- struct snd_soc_dai_link *dai_link = &hdmi->audio.link;
- struct snd_soc_card *card = &hdmi->audio.card;
- struct device *dev = &hdmi->pdev->dev;
+ struct snd_soc_dai_link *dai_link = &vc4_hdmi->audio.link;
+ struct snd_soc_card *card = &vc4_hdmi->audio.card;
+ struct device *dev = &vc4_hdmi->pdev->dev;
const __be32 *addr;
int ret;
@@ -995,9 +995,9 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
* This VC/MMU should probably be exposed to avoid this kind of hacks.
*/
addr = of_get_address(dev->of_node, 1, NULL, NULL);
- hdmi->audio.dma_data.addr = be32_to_cpup(addr) + VC4_HD_MAI_DATA;
- hdmi->audio.dma_data.addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- hdmi->audio.dma_data.maxburst = 2;
+ vc4_hdmi->audio.dma_data.addr = be32_to_cpup(addr) + VC4_HD_MAI_DATA;
+ vc4_hdmi->audio.dma_data.addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ vc4_hdmi->audio.dma_data.maxburst = 2;
ret = devm_snd_dmaengine_pcm_register(dev, &pcm_conf, 0);
if (ret) {
@@ -1020,9 +1020,9 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
return ret;
}
- dai_link->cpus = &hdmi->audio.cpu;
- dai_link->codecs = &hdmi->audio.codec;
- dai_link->platforms = &hdmi->audio.platform;
+ dai_link->cpus = &vc4_hdmi->audio.cpu;
+ dai_link->codecs = &vc4_hdmi->audio.codec;
+ dai_link->platforms = &vc4_hdmi->audio.platform;
dai_link->num_cpus = 1;
dai_link->num_codecs = 1;
@@ -1047,7 +1047,7 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
* now stored in card->drvdata and should be retrieved with
* snd_soc_card_get_drvdata() if needed.
*/
- snd_soc_card_set_drvdata(card, hdmi);
+ snd_soc_card_set_drvdata(card, vc4_hdmi);
ret = devm_snd_soc_register_card(dev, card);
if (ret)
dev_err(dev, "Could not register sound card: %d\n", ret);
@@ -1060,20 +1060,21 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
static irqreturn_t vc4_cec_irq_handler_thread(int irq, void *priv)
{
struct vc4_dev *vc4 = priv;
- struct vc4_hdmi *hdmi = vc4->hdmi;
-
- if (hdmi->cec_irq_was_rx) {
- if (hdmi->cec_rx_msg.len)
- cec_received_msg(hdmi->cec_adap, &hdmi->cec_rx_msg);
- } else if (hdmi->cec_tx_ok) {
- cec_transmit_done(hdmi->cec_adap, CEC_TX_STATUS_OK,
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+
+ if (vc4_hdmi->cec_irq_was_rx) {
+ if (vc4_hdmi->cec_rx_msg.len)
+ cec_received_msg(vc4_hdmi->cec_adap,
+ &vc4_hdmi->cec_rx_msg);
+ } else if (vc4_hdmi->cec_tx_ok) {
+ cec_transmit_done(vc4_hdmi->cec_adap, CEC_TX_STATUS_OK,
0, 0, 0, 0);
} else {
/*
* This CEC implementation makes 1 retry, so if we
* get a NACK, then that means it made 2 attempts.
*/
- cec_transmit_done(hdmi->cec_adap, CEC_TX_STATUS_NACK,
+ cec_transmit_done(vc4_hdmi->cec_adap, CEC_TX_STATUS_NACK,
0, 2, 0, 0);
}
return IRQ_HANDLED;
@@ -1099,23 +1100,23 @@ static void vc4_cec_read_msg(struct vc4_dev *vc4, u32 cntrl1)
static irqreturn_t vc4_cec_irq_handler(int irq, void *priv)
{
struct vc4_dev *vc4 = priv;
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 stat = HDMI_READ(VC4_HDMI_CPU_STATUS);
u32 cntrl1, cntrl5;
if (!(stat & VC4_HDMI_CPU_CEC))
return IRQ_NONE;
- hdmi->cec_rx_msg.len = 0;
+ vc4_hdmi->cec_rx_msg.len = 0;
cntrl1 = HDMI_READ(VC4_HDMI_CEC_CNTRL_1);
cntrl5 = HDMI_READ(VC4_HDMI_CEC_CNTRL_5);
- hdmi->cec_irq_was_rx = cntrl5 & VC4_HDMI_CEC_RX_CEC_INT;
- if (hdmi->cec_irq_was_rx) {
+ vc4_hdmi->cec_irq_was_rx = cntrl5 & VC4_HDMI_CEC_RX_CEC_INT;
+ if (vc4_hdmi->cec_irq_was_rx) {
vc4_cec_read_msg(vc4, cntrl1);
cntrl1 |= VC4_HDMI_CEC_CLEAR_RECEIVE_OFF;
HDMI_WRITE(VC4_HDMI_CEC_CNTRL_1, cntrl1);
cntrl1 &= ~VC4_HDMI_CEC_CLEAR_RECEIVE_OFF;
} else {
- hdmi->cec_tx_ok = cntrl1 & VC4_HDMI_CEC_TX_STATUS_GOOD;
+ vc4_hdmi->cec_tx_ok = cntrl1 & VC4_HDMI_CEC_TX_STATUS_GOOD;
cntrl1 &= ~VC4_HDMI_CEC_START_XMIT_BEGIN;
}
HDMI_WRITE(VC4_HDMI_CEC_CNTRL_1, cntrl1);
@@ -1217,46 +1218,46 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
struct platform_device *pdev = to_platform_device(dev);
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *hdmi;
+ struct vc4_hdmi *vc4_hdmi;
struct drm_encoder *encoder;
struct device_node *ddc_node;
u32 value;
int ret;
- hdmi = devm_kzalloc(dev, sizeof(*hdmi), GFP_KERNEL);
- if (!hdmi)
+ vc4_hdmi = devm_kzalloc(dev, sizeof(*vc4_hdmi), GFP_KERNEL);
+ if (!vc4_hdmi)
return -ENOMEM;
- encoder = &hdmi->encoder.base.base;
- hdmi->encoder.base.type = VC4_ENCODER_TYPE_HDMI0;
- hdmi->pdev = pdev;
+ encoder = &vc4_hdmi->encoder.base.base;
+ vc4_hdmi->encoder.base.type = VC4_ENCODER_TYPE_HDMI0;
+ vc4_hdmi->pdev = pdev;
- hdmi->hdmicore_regs = vc4_ioremap_regs(pdev, 0);
- if (IS_ERR(hdmi->hdmicore_regs))
- return PTR_ERR(hdmi->hdmicore_regs);
+ vc4_hdmi->hdmicore_regs = vc4_ioremap_regs(pdev, 0);
+ if (IS_ERR(vc4_hdmi->hdmicore_regs))
+ return PTR_ERR(vc4_hdmi->hdmicore_regs);
- hdmi->hd_regs = vc4_ioremap_regs(pdev, 1);
- if (IS_ERR(hdmi->hd_regs))
- return PTR_ERR(hdmi->hd_regs);
+ vc4_hdmi->hd_regs = vc4_ioremap_regs(pdev, 1);
+ if (IS_ERR(vc4_hdmi->hd_regs))
+ return PTR_ERR(vc4_hdmi->hd_regs);
- hdmi->hdmi_regset.base = hdmi->hdmicore_regs;
- hdmi->hdmi_regset.regs = hdmi_regs;
- hdmi->hdmi_regset.nregs = ARRAY_SIZE(hdmi_regs);
- hdmi->hd_regset.base = hdmi->hd_regs;
- hdmi->hd_regset.regs = hd_regs;
- hdmi->hd_regset.nregs = ARRAY_SIZE(hd_regs);
+ vc4_hdmi->hdmi_regset.base = vc4_hdmi->hdmicore_regs;
+ vc4_hdmi->hdmi_regset.regs = hdmi_regs;
+ vc4_hdmi->hdmi_regset.nregs = ARRAY_SIZE(hdmi_regs);
+ vc4_hdmi->hd_regset.base = vc4_hdmi->hd_regs;
+ vc4_hdmi->hd_regset.regs = hd_regs;
+ vc4_hdmi->hd_regset.nregs = ARRAY_SIZE(hd_regs);
- hdmi->pixel_clock = devm_clk_get(dev, "pixel");
- if (IS_ERR(hdmi->pixel_clock)) {
- ret = PTR_ERR(hdmi->pixel_clock);
+ vc4_hdmi->pixel_clock = devm_clk_get(dev, "pixel");
+ if (IS_ERR(vc4_hdmi->pixel_clock)) {
+ ret = PTR_ERR(vc4_hdmi->pixel_clock);
if (ret != -EPROBE_DEFER)
DRM_ERROR("Failed to get pixel clock\n");
return ret;
}
- hdmi->hsm_clock = devm_clk_get(dev, "hdmi");
- if (IS_ERR(hdmi->hsm_clock)) {
+ vc4_hdmi->hsm_clock = devm_clk_get(dev, "hdmi");
+ if (IS_ERR(vc4_hdmi->hsm_clock)) {
DRM_ERROR("Failed to get HDMI state machine clock\n");
- return PTR_ERR(hdmi->hsm_clock);
+ return PTR_ERR(vc4_hdmi->hsm_clock);
}
ddc_node = of_parse_phandle(dev->of_node, "ddc", 0);
@@ -1265,9 +1266,9 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
return -ENODEV;
}
- hdmi->ddc = of_find_i2c_adapter_by_node(ddc_node);
+ vc4_hdmi->ddc = of_find_i2c_adapter_by_node(ddc_node);
of_node_put(ddc_node);
- if (!hdmi->ddc) {
+ if (!vc4_hdmi->ddc) {
DRM_DEBUG("Failed to get ddc i2c adapter by node\n");
return -EPROBE_DEFER;
}
@@ -1276,13 +1277,13 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
* needs to be a bit higher than the pixel clock rate
* (generally 148.5Mhz).
*/
- ret = clk_set_rate(hdmi->hsm_clock, HSM_CLOCK_FREQ);
+ ret = clk_set_rate(vc4_hdmi->hsm_clock, HSM_CLOCK_FREQ);
if (ret) {
DRM_ERROR("Failed to set HSM clock rate: %d\n", ret);
goto err_put_i2c;
}
- ret = clk_prepare_enable(hdmi->hsm_clock);
+ ret = clk_prepare_enable(vc4_hdmi->hsm_clock);
if (ret) {
DRM_ERROR("Failed to turn on HDMI state machine clock: %d\n",
ret);
@@ -1295,18 +1296,18 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
if (of_find_property(dev->of_node, "hpd-gpios", &value)) {
enum of_gpio_flags hpd_gpio_flags;
- hdmi->hpd_gpio = of_get_named_gpio_flags(dev->of_node,
- "hpd-gpios", 0,
- &hpd_gpio_flags);
- if (hdmi->hpd_gpio < 0) {
- ret = hdmi->hpd_gpio;
+ vc4_hdmi->hpd_gpio = of_get_named_gpio_flags(dev->of_node,
+ "hpd-gpios", 0,
+ &hpd_gpio_flags);
+ if (vc4_hdmi->hpd_gpio < 0) {
+ ret = vc4_hdmi->hpd_gpio;
goto err_unprepare_hsm;
}
- hdmi->hpd_active_low = hpd_gpio_flags & OF_GPIO_ACTIVE_LOW;
+ vc4_hdmi->hpd_active_low = hpd_gpio_flags & OF_GPIO_ACTIVE_LOW;
}
- vc4->hdmi = hdmi;
+ vc4->hdmi = vc4_hdmi;
/* HDMI core must be enabled. */
if (!(HD_READ(VC4_HD_M_CTL) & VC4_HD_M_ENABLE)) {
@@ -1321,21 +1322,21 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
- ret = vc4_hdmi_connector_init(drm, hdmi);
+ ret = vc4_hdmi_connector_init(drm, vc4_hdmi);
if (ret)
goto err_destroy_encoder;
#ifdef CONFIG_DRM_VC4_HDMI_CEC
- hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
- vc4, "vc4",
- CEC_CAP_DEFAULTS |
- CEC_CAP_CONNECTOR_INFO, 1);
- ret = PTR_ERR_OR_ZERO(hdmi->cec_adap);
+ vc4_hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
+ vc4, "vc4",
+ CEC_CAP_DEFAULTS |
+ CEC_CAP_CONNECTOR_INFO, 1);
+ ret = PTR_ERR_OR_ZERO(vc4_hdmi->cec_adap);
if (ret < 0)
goto err_destroy_conn;
- cec_fill_conn_info_from_drm(&conn_info, &hdmi->connector.base);
- cec_s_conn_info(hdmi->cec_adap, &conn_info);
+ cec_fill_conn_info_from_drm(&conn_info, &vc4_hdmi->connector.base);
+ cec_s_conn_info(vc4_hdmi->cec_adap, &conn_info);
HDMI_WRITE(VC4_HDMI_CPU_MASK_SET, 0xffffffff);
value = HDMI_READ(VC4_HDMI_CEC_CNTRL_1);
@@ -1354,32 +1355,32 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
"vc4 hdmi cec", vc4);
if (ret)
goto err_delete_cec_adap;
- ret = cec_register_adapter(hdmi->cec_adap, dev);
+ ret = cec_register_adapter(vc4_hdmi->cec_adap, dev);
if (ret < 0)
goto err_delete_cec_adap;
#endif
- ret = vc4_hdmi_audio_init(hdmi);
+ ret = vc4_hdmi_audio_init(vc4_hdmi);
if (ret)
goto err_destroy_encoder;
- vc4_debugfs_add_file(drm, "hdmi_regs", vc4_hdmi_debugfs_regs, hdmi);
+ vc4_debugfs_add_file(drm, "hdmi_regs", vc4_hdmi_debugfs_regs, vc4_hdmi);
return 0;
#ifdef CONFIG_DRM_VC4_HDMI_CEC
err_delete_cec_adap:
- cec_delete_adapter(hdmi->cec_adap);
+ cec_delete_adapter(vc4_hdmi->cec_adap);
err_destroy_conn:
- vc4_hdmi_connector_destroy(&hdmi->connector.base);
+ vc4_hdmi_connector_destroy(&vc4_hdmi->connector.base);
#endif
err_destroy_encoder:
drm_encoder_cleanup(encoder);
err_unprepare_hsm:
- clk_disable_unprepare(hdmi->hsm_clock);
+ clk_disable_unprepare(vc4_hdmi->hsm_clock);
pm_runtime_disable(dev);
err_put_i2c:
- put_device(&hdmi->ddc->dev);
+ put_device(&vc4_hdmi->ddc->dev);
return ret;
}
@@ -1389,16 +1390,16 @@ static void vc4_hdmi_unbind(struct device *dev, struct device *master,
{
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
- cec_unregister_adapter(hdmi->cec_adap);
- vc4_hdmi_connector_destroy(&hdmi->connector.base);
- drm_encoder_cleanup(&hdmi->encoder.base.base);
+ cec_unregister_adapter(vc4_hdmi->cec_adap);
+ vc4_hdmi_connector_destroy(&vc4_hdmi->connector.base);
+ drm_encoder_cleanup(&vc4_hdmi->encoder.base.base);
- clk_disable_unprepare(hdmi->hsm_clock);
+ clk_disable_unprepare(vc4_hdmi->hsm_clock);
pm_runtime_disable(dev);
- put_device(&hdmi->ddc->dev);
+ put_device(&vc4_hdmi->ddc->dev);
vc4->hdmi = NULL;
}
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 42/80] drm/vc4: hdmi: Rename hdmi to vc4_hdmi
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The driver isn't consistent with the name given to the vc4_hdmi
structure pointer in its functions. Make sure to use a consistent name.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 283 +++++++++++++++++-----------------
1 file changed, 142 insertions(+), 141 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 1f350b068fcd..6733e4bc235b 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -109,11 +109,11 @@ static const struct debugfs_reg32 hd_regs[] = {
static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
{
struct drm_info_node *node = (struct drm_info_node *)m->private;
- struct vc4_hdmi *hdmi = node->info_ent->data;
+ struct vc4_hdmi *vc4_hdmi = node->info_ent->data;
struct drm_printer p = drm_seq_file_printer(m);
- drm_print_regset32(&p, &hdmi->hdmi_regset);
- drm_print_regset32(&p, &hdmi->hd_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hdmi_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hd_regset);
return 0;
}
@@ -291,8 +291,8 @@ static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
{
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
struct vc4_dev *vc4 = encoder->dev->dev_private;
- struct vc4_hdmi *hdmi = vc4->hdmi;
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
struct drm_connector_state *cstate = connector->state;
struct drm_crtc *crtc = encoder->crtc;
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
@@ -337,7 +337,7 @@ static void vc4_hdmi_set_audio_infoframe(struct drm_encoder *encoder)
{
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
union hdmi_infoframe frame;
int ret;
@@ -346,7 +346,7 @@ static void vc4_hdmi_set_audio_infoframe(struct drm_encoder *encoder)
frame.audio.coding_type = HDMI_AUDIO_CODING_TYPE_STREAM;
frame.audio.sample_frequency = HDMI_AUDIO_SAMPLE_FREQUENCY_STREAM;
frame.audio.sample_size = HDMI_AUDIO_SAMPLE_SIZE_STREAM;
- frame.audio.channels = hdmi->audio.channels;
+ frame.audio.channels = vc4_hdmi->audio.channels;
vc4_hdmi_write_infoframe(encoder, &frame);
}
@@ -361,7 +361,7 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
{
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
int ret;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG, 0);
@@ -370,9 +370,9 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
HD_WRITE(VC4_HD_VID_CTL,
HD_READ(VC4_HD_VID_CTL) & ~VC4_HD_VID_CTL_ENABLE);
- clk_disable_unprepare(hdmi->pixel_clock);
+ clk_disable_unprepare(vc4_hdmi->pixel_clock);
- ret = pm_runtime_put(&hdmi->pdev->dev);
+ ret = pm_runtime_put(&vc4_hdmi->pdev->dev);
if (ret < 0)
DRM_ERROR("Failed to release power domain: %d\n", ret);
}
@@ -383,7 +383,7 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
bool debug_dump_regs = false;
bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
@@ -405,13 +405,13 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
u32 csc_ctl;
int ret;
- ret = pm_runtime_get_sync(&hdmi->pdev->dev);
+ ret = pm_runtime_get_sync(&vc4_hdmi->pdev->dev);
if (ret < 0) {
DRM_ERROR("Failed to retain power domain: %d\n", ret);
return;
}
- ret = clk_set_rate(hdmi->pixel_clock,
+ ret = clk_set_rate(vc4_hdmi->pixel_clock,
mode->clock * 1000 *
((mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1));
if (ret) {
@@ -419,7 +419,7 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
return;
}
- ret = clk_prepare_enable(hdmi->pixel_clock);
+ ret = clk_prepare_enable(vc4_hdmi->pixel_clock);
if (ret) {
DRM_ERROR("Failed to turn on pixel clock: %d\n", ret);
return;
@@ -439,11 +439,11 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
HDMI_WRITE(VC4_HDMI_TX_PHY_RESET_CTL, 0);
if (debug_dump_regs) {
- struct drm_printer p = drm_info_printer(&hdmi->pdev->dev);
+ struct drm_printer p = drm_info_printer(&vc4_hdmi->pdev->dev);
- dev_info(&hdmi->pdev->dev, "HDMI regs before:\n");
- drm_print_regset32(&p, &hdmi->hdmi_regset);
- drm_print_regset32(&p, &hdmi->hd_regset);
+ dev_info(&vc4_hdmi->pdev->dev, "HDMI regs before:\n");
+ drm_print_regset32(&p, &vc4_hdmi->hdmi_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hd_regset);
}
HD_WRITE(VC4_HD_VID_CTL, 0);
@@ -518,11 +518,11 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
HDMI_WRITE(VC4_HDMI_FIFO_CTL, VC4_HDMI_FIFO_CTL_MASTER_SLAVE_N);
if (debug_dump_regs) {
- struct drm_printer p = drm_info_printer(&hdmi->pdev->dev);
+ struct drm_printer p = drm_info_printer(&vc4_hdmi->pdev->dev);
- dev_info(&hdmi->pdev->dev, "HDMI regs after:\n");
- drm_print_regset32(&p, &hdmi->hdmi_regset);
- drm_print_regset32(&p, &hdmi->hd_regset);
+ dev_info(&vc4_hdmi->pdev->dev, "HDMI regs after:\n");
+ drm_print_regset32(&p, &vc4_hdmi->hdmi_regset);
+ drm_print_regset32(&p, &vc4_hdmi->hd_regset);
}
HD_WRITE(VC4_HD_VID_CTL,
@@ -621,15 +621,15 @@ static const struct drm_encoder_helper_funcs vc4_hdmi_encoder_helper_funcs = {
};
/* HDMI audio codec callbacks */
-static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
+static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
- u32 hsm_clock = clk_get_rate(hdmi->hsm_clock);
+ u32 hsm_clock = clk_get_rate(vc4_hdmi->hsm_clock);
unsigned long n, m;
- rational_best_approximation(hsm_clock, hdmi->audio.samplerate,
+ rational_best_approximation(hsm_clock, vc4_hdmi->audio.samplerate,
VC4_HD_MAI_SMP_N_MASK >>
VC4_HD_MAI_SMP_N_SHIFT,
(VC4_HD_MAI_SMP_M_MASK >>
@@ -641,14 +641,14 @@ static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *hdmi)
VC4_SET_FIELD(m - 1, VC4_HD_MAI_SMP_M));
}
-static void vc4_hdmi_set_n_cts(struct vc4_hdmi *hdmi)
+static void vc4_hdmi_set_n_cts(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_crtc *crtc = encoder->crtc;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
- u32 samplerate = hdmi->audio.samplerate;
+ u32 samplerate = vc4_hdmi->audio.samplerate;
u32 n, cts;
u64 tmp;
@@ -680,16 +680,16 @@ static inline struct vc4_hdmi *dai_to_hdmi(struct snd_soc_dai *dai)
static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
struct vc4_dev *vc4 = to_vc4_dev(encoder->dev);
int ret;
- if (hdmi->audio.substream && hdmi->audio.substream != substream)
+ if (vc4_hdmi->audio.substream && vc4_hdmi->audio.substream != substream)
return -EINVAL;
- hdmi->audio.substream = substream;
+ vc4_hdmi->audio.substream = substream;
/*
* If the HDMI encoder hasn't probed, or the encoder is
@@ -711,11 +711,11 @@ static int vc4_hdmi_audio_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
return 0;
}
-static void vc4_hdmi_audio_reset(struct vc4_hdmi *hdmi)
+static void vc4_hdmi_audio_reset(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
- struct device *dev = &hdmi->pdev->dev;
+ struct device *dev = &vc4_hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
int ret;
@@ -731,14 +731,14 @@ static void vc4_hdmi_audio_reset(struct vc4_hdmi *hdmi)
static void vc4_hdmi_audio_shutdown(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
- if (substream != hdmi->audio.substream)
+ if (substream != vc4_hdmi->audio.substream)
return;
- vc4_hdmi_audio_reset(hdmi);
+ vc4_hdmi_audio_reset(vc4_hdmi);
- hdmi->audio.substream = NULL;
+ vc4_hdmi->audio.substream = NULL;
}
/* HDMI audio codec callbacks */
@@ -746,23 +746,23 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
- struct device *dev = &hdmi->pdev->dev;
+ struct device *dev = &vc4_hdmi->pdev->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 audio_packet_config, channel_mask;
u32 channel_map, i;
- if (substream != hdmi->audio.substream)
+ if (substream != vc4_hdmi->audio.substream)
return -EINVAL;
dev_dbg(dev, "%s: %u Hz, %d bit, %d channels\n", __func__,
params_rate(params), params_width(params),
params_channels(params));
- hdmi->audio.channels = params_channels(params);
- hdmi->audio.samplerate = params_rate(params);
+ vc4_hdmi->audio.channels = params_channels(params);
+ vc4_hdmi->audio.samplerate = params_rate(params);
HD_WRITE(VC4_HD_MAI_CTL,
VC4_HD_MAI_CTL_RESET |
@@ -771,23 +771,23 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
VC4_HD_MAI_CTL_ERRORE |
VC4_HD_MAI_CTL_ERRORF);
- vc4_hdmi_audio_set_mai_clock(hdmi);
+ vc4_hdmi_audio_set_mai_clock(vc4_hdmi);
audio_packet_config =
VC4_HDMI_AUDIO_PACKET_ZERO_DATA_ON_SAMPLE_FLAT |
VC4_HDMI_AUDIO_PACKET_ZERO_DATA_ON_INACTIVE_CHANNELS |
VC4_SET_FIELD(0xf, VC4_HDMI_AUDIO_PACKET_B_FRAME_IDENTIFIER);
- channel_mask = GENMASK(hdmi->audio.channels - 1, 0);
+ channel_mask = GENMASK(vc4_hdmi->audio.channels - 1, 0);
audio_packet_config |= VC4_SET_FIELD(channel_mask,
VC4_HDMI_AUDIO_PACKET_CEA_MASK);
/* Set the MAI threshold. This logic mimics the firmware's. */
- if (hdmi->audio.samplerate > 96000) {
+ if (vc4_hdmi->audio.samplerate > 96000) {
HD_WRITE(VC4_HD_MAI_THR,
VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQHIGH) |
VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQLOW));
- } else if (hdmi->audio.samplerate > 48000) {
+ } else if (vc4_hdmi->audio.samplerate > 48000) {
HD_WRITE(VC4_HD_MAI_THR,
VC4_SET_FIELD(0x14, VC4_HD_MAI_THR_DREQHIGH) |
VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQLOW));
@@ -811,7 +811,7 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
HDMI_WRITE(VC4_HDMI_MAI_CHANNEL_MAP, channel_map);
HDMI_WRITE(VC4_HDMI_AUDIO_PACKET_CONFIG, audio_packet_config);
- vc4_hdmi_set_n_cts(hdmi);
+ vc4_hdmi_set_n_cts(vc4_hdmi);
return 0;
}
@@ -819,8 +819,8 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &hdmi->encoder.base.base;
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
+ struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_device *drm = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(drm);
@@ -831,7 +831,7 @@ static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
HDMI_READ(VC4_HDMI_TX_PHY_CTL0) &
~VC4_HDMI_TX_PHY_RNG_PWRDN);
HD_WRITE(VC4_HD_MAI_CTL,
- VC4_SET_FIELD(hdmi->audio.channels,
+ VC4_SET_FIELD(vc4_hdmi->audio.channels,
VC4_HD_MAI_CTL_CHNUM) |
VC4_HD_MAI_CTL_ENABLE);
break;
@@ -863,8 +863,8 @@ static int vc4_hdmi_audio_eld_ctl_info(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_info *uinfo)
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
- struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
uinfo->type = SNDRV_CTL_ELEM_TYPE_BYTES;
uinfo->count = sizeof(connector->eld);
@@ -876,8 +876,8 @@ static int vc4_hdmi_audio_eld_ctl_get(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
- struct vc4_hdmi *hdmi = snd_component_to_hdmi(component);
- struct drm_connector *connector = &hdmi->connector.base;
+ struct vc4_hdmi *vc4_hdmi = snd_component_to_hdmi(component);
+ struct drm_connector *connector = &vc4_hdmi->connector.base;
memcpy(ucontrol->value.bytes.data, connector->eld,
sizeof(connector->eld));
@@ -945,9 +945,9 @@ static const struct snd_soc_component_driver vc4_hdmi_audio_cpu_dai_comp = {
static int vc4_hdmi_audio_cpu_dai_probe(struct snd_soc_dai *dai)
{
- struct vc4_hdmi *hdmi = dai_to_hdmi(dai);
+ struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
- snd_soc_dai_init_dma_data(dai, &hdmi->audio.dma_data, NULL);
+ snd_soc_dai_init_dma_data(dai, &vc4_hdmi->audio.dma_data, NULL);
return 0;
}
@@ -973,11 +973,11 @@ static const struct snd_dmaengine_pcm_config pcm_conf = {
.prepare_slave_config = snd_dmaengine_pcm_prepare_slave_config,
};
-static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
+static int vc4_hdmi_audio_init(struct vc4_hdmi *vc4_hdmi)
{
- struct snd_soc_dai_link *dai_link = &hdmi->audio.link;
- struct snd_soc_card *card = &hdmi->audio.card;
- struct device *dev = &hdmi->pdev->dev;
+ struct snd_soc_dai_link *dai_link = &vc4_hdmi->audio.link;
+ struct snd_soc_card *card = &vc4_hdmi->audio.card;
+ struct device *dev = &vc4_hdmi->pdev->dev;
const __be32 *addr;
int ret;
@@ -995,9 +995,9 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
* This VC/MMU should probably be exposed to avoid this kind of hacks.
*/
addr = of_get_address(dev->of_node, 1, NULL, NULL);
- hdmi->audio.dma_data.addr = be32_to_cpup(addr) + VC4_HD_MAI_DATA;
- hdmi->audio.dma_data.addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- hdmi->audio.dma_data.maxburst = 2;
+ vc4_hdmi->audio.dma_data.addr = be32_to_cpup(addr) + VC4_HD_MAI_DATA;
+ vc4_hdmi->audio.dma_data.addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ vc4_hdmi->audio.dma_data.maxburst = 2;
ret = devm_snd_dmaengine_pcm_register(dev, &pcm_conf, 0);
if (ret) {
@@ -1020,9 +1020,9 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
return ret;
}
- dai_link->cpus = &hdmi->audio.cpu;
- dai_link->codecs = &hdmi->audio.codec;
- dai_link->platforms = &hdmi->audio.platform;
+ dai_link->cpus = &vc4_hdmi->audio.cpu;
+ dai_link->codecs = &vc4_hdmi->audio.codec;
+ dai_link->platforms = &vc4_hdmi->audio.platform;
dai_link->num_cpus = 1;
dai_link->num_codecs = 1;
@@ -1047,7 +1047,7 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
* now stored in card->drvdata and should be retrieved with
* snd_soc_card_get_drvdata() if needed.
*/
- snd_soc_card_set_drvdata(card, hdmi);
+ snd_soc_card_set_drvdata(card, vc4_hdmi);
ret = devm_snd_soc_register_card(dev, card);
if (ret)
dev_err(dev, "Could not register sound card: %d\n", ret);
@@ -1060,20 +1060,21 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *hdmi)
static irqreturn_t vc4_cec_irq_handler_thread(int irq, void *priv)
{
struct vc4_dev *vc4 = priv;
- struct vc4_hdmi *hdmi = vc4->hdmi;
-
- if (hdmi->cec_irq_was_rx) {
- if (hdmi->cec_rx_msg.len)
- cec_received_msg(hdmi->cec_adap, &hdmi->cec_rx_msg);
- } else if (hdmi->cec_tx_ok) {
- cec_transmit_done(hdmi->cec_adap, CEC_TX_STATUS_OK,
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+
+ if (vc4_hdmi->cec_irq_was_rx) {
+ if (vc4_hdmi->cec_rx_msg.len)
+ cec_received_msg(vc4_hdmi->cec_adap,
+ &vc4_hdmi->cec_rx_msg);
+ } else if (vc4_hdmi->cec_tx_ok) {
+ cec_transmit_done(vc4_hdmi->cec_adap, CEC_TX_STATUS_OK,
0, 0, 0, 0);
} else {
/*
* This CEC implementation makes 1 retry, so if we
* get a NACK, then that means it made 2 attempts.
*/
- cec_transmit_done(hdmi->cec_adap, CEC_TX_STATUS_NACK,
+ cec_transmit_done(vc4_hdmi->cec_adap, CEC_TX_STATUS_NACK,
0, 2, 0, 0);
}
return IRQ_HANDLED;
@@ -1099,23 +1100,23 @@ static void vc4_cec_read_msg(struct vc4_dev *vc4, u32 cntrl1)
static irqreturn_t vc4_cec_irq_handler(int irq, void *priv)
{
struct vc4_dev *vc4 = priv;
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 stat = HDMI_READ(VC4_HDMI_CPU_STATUS);
u32 cntrl1, cntrl5;
if (!(stat & VC4_HDMI_CPU_CEC))
return IRQ_NONE;
- hdmi->cec_rx_msg.len = 0;
+ vc4_hdmi->cec_rx_msg.len = 0;
cntrl1 = HDMI_READ(VC4_HDMI_CEC_CNTRL_1);
cntrl5 = HDMI_READ(VC4_HDMI_CEC_CNTRL_5);
- hdmi->cec_irq_was_rx = cntrl5 & VC4_HDMI_CEC_RX_CEC_INT;
- if (hdmi->cec_irq_was_rx) {
+ vc4_hdmi->cec_irq_was_rx = cntrl5 & VC4_HDMI_CEC_RX_CEC_INT;
+ if (vc4_hdmi->cec_irq_was_rx) {
vc4_cec_read_msg(vc4, cntrl1);
cntrl1 |= VC4_HDMI_CEC_CLEAR_RECEIVE_OFF;
HDMI_WRITE(VC4_HDMI_CEC_CNTRL_1, cntrl1);
cntrl1 &= ~VC4_HDMI_CEC_CLEAR_RECEIVE_OFF;
} else {
- hdmi->cec_tx_ok = cntrl1 & VC4_HDMI_CEC_TX_STATUS_GOOD;
+ vc4_hdmi->cec_tx_ok = cntrl1 & VC4_HDMI_CEC_TX_STATUS_GOOD;
cntrl1 &= ~VC4_HDMI_CEC_START_XMIT_BEGIN;
}
HDMI_WRITE(VC4_HDMI_CEC_CNTRL_1, cntrl1);
@@ -1217,46 +1218,46 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
struct platform_device *pdev = to_platform_device(dev);
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *hdmi;
+ struct vc4_hdmi *vc4_hdmi;
struct drm_encoder *encoder;
struct device_node *ddc_node;
u32 value;
int ret;
- hdmi = devm_kzalloc(dev, sizeof(*hdmi), GFP_KERNEL);
- if (!hdmi)
+ vc4_hdmi = devm_kzalloc(dev, sizeof(*vc4_hdmi), GFP_KERNEL);
+ if (!vc4_hdmi)
return -ENOMEM;
- encoder = &hdmi->encoder.base.base;
- hdmi->encoder.base.type = VC4_ENCODER_TYPE_HDMI0;
- hdmi->pdev = pdev;
+ encoder = &vc4_hdmi->encoder.base.base;
+ vc4_hdmi->encoder.base.type = VC4_ENCODER_TYPE_HDMI0;
+ vc4_hdmi->pdev = pdev;
- hdmi->hdmicore_regs = vc4_ioremap_regs(pdev, 0);
- if (IS_ERR(hdmi->hdmicore_regs))
- return PTR_ERR(hdmi->hdmicore_regs);
+ vc4_hdmi->hdmicore_regs = vc4_ioremap_regs(pdev, 0);
+ if (IS_ERR(vc4_hdmi->hdmicore_regs))
+ return PTR_ERR(vc4_hdmi->hdmicore_regs);
- hdmi->hd_regs = vc4_ioremap_regs(pdev, 1);
- if (IS_ERR(hdmi->hd_regs))
- return PTR_ERR(hdmi->hd_regs);
+ vc4_hdmi->hd_regs = vc4_ioremap_regs(pdev, 1);
+ if (IS_ERR(vc4_hdmi->hd_regs))
+ return PTR_ERR(vc4_hdmi->hd_regs);
- hdmi->hdmi_regset.base = hdmi->hdmicore_regs;
- hdmi->hdmi_regset.regs = hdmi_regs;
- hdmi->hdmi_regset.nregs = ARRAY_SIZE(hdmi_regs);
- hdmi->hd_regset.base = hdmi->hd_regs;
- hdmi->hd_regset.regs = hd_regs;
- hdmi->hd_regset.nregs = ARRAY_SIZE(hd_regs);
+ vc4_hdmi->hdmi_regset.base = vc4_hdmi->hdmicore_regs;
+ vc4_hdmi->hdmi_regset.regs = hdmi_regs;
+ vc4_hdmi->hdmi_regset.nregs = ARRAY_SIZE(hdmi_regs);
+ vc4_hdmi->hd_regset.base = vc4_hdmi->hd_regs;
+ vc4_hdmi->hd_regset.regs = hd_regs;
+ vc4_hdmi->hd_regset.nregs = ARRAY_SIZE(hd_regs);
- hdmi->pixel_clock = devm_clk_get(dev, "pixel");
- if (IS_ERR(hdmi->pixel_clock)) {
- ret = PTR_ERR(hdmi->pixel_clock);
+ vc4_hdmi->pixel_clock = devm_clk_get(dev, "pixel");
+ if (IS_ERR(vc4_hdmi->pixel_clock)) {
+ ret = PTR_ERR(vc4_hdmi->pixel_clock);
if (ret != -EPROBE_DEFER)
DRM_ERROR("Failed to get pixel clock\n");
return ret;
}
- hdmi->hsm_clock = devm_clk_get(dev, "hdmi");
- if (IS_ERR(hdmi->hsm_clock)) {
+ vc4_hdmi->hsm_clock = devm_clk_get(dev, "hdmi");
+ if (IS_ERR(vc4_hdmi->hsm_clock)) {
DRM_ERROR("Failed to get HDMI state machine clock\n");
- return PTR_ERR(hdmi->hsm_clock);
+ return PTR_ERR(vc4_hdmi->hsm_clock);
}
ddc_node = of_parse_phandle(dev->of_node, "ddc", 0);
@@ -1265,9 +1266,9 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
return -ENODEV;
}
- hdmi->ddc = of_find_i2c_adapter_by_node(ddc_node);
+ vc4_hdmi->ddc = of_find_i2c_adapter_by_node(ddc_node);
of_node_put(ddc_node);
- if (!hdmi->ddc) {
+ if (!vc4_hdmi->ddc) {
DRM_DEBUG("Failed to get ddc i2c adapter by node\n");
return -EPROBE_DEFER;
}
@@ -1276,13 +1277,13 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
* needs to be a bit higher than the pixel clock rate
* (generally 148.5Mhz).
*/
- ret = clk_set_rate(hdmi->hsm_clock, HSM_CLOCK_FREQ);
+ ret = clk_set_rate(vc4_hdmi->hsm_clock, HSM_CLOCK_FREQ);
if (ret) {
DRM_ERROR("Failed to set HSM clock rate: %d\n", ret);
goto err_put_i2c;
}
- ret = clk_prepare_enable(hdmi->hsm_clock);
+ ret = clk_prepare_enable(vc4_hdmi->hsm_clock);
if (ret) {
DRM_ERROR("Failed to turn on HDMI state machine clock: %d\n",
ret);
@@ -1295,18 +1296,18 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
if (of_find_property(dev->of_node, "hpd-gpios", &value)) {
enum of_gpio_flags hpd_gpio_flags;
- hdmi->hpd_gpio = of_get_named_gpio_flags(dev->of_node,
- "hpd-gpios", 0,
- &hpd_gpio_flags);
- if (hdmi->hpd_gpio < 0) {
- ret = hdmi->hpd_gpio;
+ vc4_hdmi->hpd_gpio = of_get_named_gpio_flags(dev->of_node,
+ "hpd-gpios", 0,
+ &hpd_gpio_flags);
+ if (vc4_hdmi->hpd_gpio < 0) {
+ ret = vc4_hdmi->hpd_gpio;
goto err_unprepare_hsm;
}
- hdmi->hpd_active_low = hpd_gpio_flags & OF_GPIO_ACTIVE_LOW;
+ vc4_hdmi->hpd_active_low = hpd_gpio_flags & OF_GPIO_ACTIVE_LOW;
}
- vc4->hdmi = hdmi;
+ vc4->hdmi = vc4_hdmi;
/* HDMI core must be enabled. */
if (!(HD_READ(VC4_HD_M_CTL) & VC4_HD_M_ENABLE)) {
@@ -1321,21 +1322,21 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
drm_simple_encoder_init(drm, encoder, DRM_MODE_ENCODER_TMDS);
drm_encoder_helper_add(encoder, &vc4_hdmi_encoder_helper_funcs);
- ret = vc4_hdmi_connector_init(drm, hdmi);
+ ret = vc4_hdmi_connector_init(drm, vc4_hdmi);
if (ret)
goto err_destroy_encoder;
#ifdef CONFIG_DRM_VC4_HDMI_CEC
- hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
- vc4, "vc4",
- CEC_CAP_DEFAULTS |
- CEC_CAP_CONNECTOR_INFO, 1);
- ret = PTR_ERR_OR_ZERO(hdmi->cec_adap);
+ vc4_hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops,
+ vc4, "vc4",
+ CEC_CAP_DEFAULTS |
+ CEC_CAP_CONNECTOR_INFO, 1);
+ ret = PTR_ERR_OR_ZERO(vc4_hdmi->cec_adap);
if (ret < 0)
goto err_destroy_conn;
- cec_fill_conn_info_from_drm(&conn_info, &hdmi->connector.base);
- cec_s_conn_info(hdmi->cec_adap, &conn_info);
+ cec_fill_conn_info_from_drm(&conn_info, &vc4_hdmi->connector.base);
+ cec_s_conn_info(vc4_hdmi->cec_adap, &conn_info);
HDMI_WRITE(VC4_HDMI_CPU_MASK_SET, 0xffffffff);
value = HDMI_READ(VC4_HDMI_CEC_CNTRL_1);
@@ -1354,32 +1355,32 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
"vc4 hdmi cec", vc4);
if (ret)
goto err_delete_cec_adap;
- ret = cec_register_adapter(hdmi->cec_adap, dev);
+ ret = cec_register_adapter(vc4_hdmi->cec_adap, dev);
if (ret < 0)
goto err_delete_cec_adap;
#endif
- ret = vc4_hdmi_audio_init(hdmi);
+ ret = vc4_hdmi_audio_init(vc4_hdmi);
if (ret)
goto err_destroy_encoder;
- vc4_debugfs_add_file(drm, "hdmi_regs", vc4_hdmi_debugfs_regs, hdmi);
+ vc4_debugfs_add_file(drm, "hdmi_regs", vc4_hdmi_debugfs_regs, vc4_hdmi);
return 0;
#ifdef CONFIG_DRM_VC4_HDMI_CEC
err_delete_cec_adap:
- cec_delete_adapter(hdmi->cec_adap);
+ cec_delete_adapter(vc4_hdmi->cec_adap);
err_destroy_conn:
- vc4_hdmi_connector_destroy(&hdmi->connector.base);
+ vc4_hdmi_connector_destroy(&vc4_hdmi->connector.base);
#endif
err_destroy_encoder:
drm_encoder_cleanup(encoder);
err_unprepare_hsm:
- clk_disable_unprepare(hdmi->hsm_clock);
+ clk_disable_unprepare(vc4_hdmi->hsm_clock);
pm_runtime_disable(dev);
err_put_i2c:
- put_device(&hdmi->ddc->dev);
+ put_device(&vc4_hdmi->ddc->dev);
return ret;
}
@@ -1389,16 +1390,16 @@ static void vc4_hdmi_unbind(struct device *dev, struct device *master,
{
struct drm_device *drm = dev_get_drvdata(master);
struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
- cec_unregister_adapter(hdmi->cec_adap);
- vc4_hdmi_connector_destroy(&hdmi->connector.base);
- drm_encoder_cleanup(&hdmi->encoder.base.base);
+ cec_unregister_adapter(vc4_hdmi->cec_adap);
+ vc4_hdmi_connector_destroy(&vc4_hdmi->connector.base);
+ drm_encoder_cleanup(&vc4_hdmi->encoder.base.base);
- clk_disable_unprepare(hdmi->hsm_clock);
+ clk_disable_unprepare(vc4_hdmi->hsm_clock);
pm_runtime_disable(dev);
- put_device(&hdmi->ddc->dev);
+ put_device(&vc4_hdmi->ddc->dev);
vc4->hdmi = NULL;
}
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 43/80] drm/vc4: hdmi: Move accessors to vc4_hdmi
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The current driver only supports a single HDMI controller, and part of
the issue is that the main vc4_dev structure holds a pointer to its
(only) HDMI controller, and the HDMI registers accessors will use it to
retrieve the mapped addresses.
Let's modify those accessors to use directly the vc4_hdmi structure so
that we can eventually get rid of that single global pointer.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 22 ++++++++--------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 8 ++++----
2 files changed, 12 insertions(+), 18 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 6733e4bc235b..81c0f67cd0eb 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -123,6 +123,7 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
{
struct drm_device *dev = connector->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
if (vc4->hdmi->hpd_gpio) {
if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
@@ -230,6 +231,7 @@ static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
{
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 packet_id = type - 0x80;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG,
@@ -244,6 +246,7 @@ static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
{
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 packet_id = frame->any.type - 0x80;
u32 packet_reg = VC4_HDMI_RAM_PACKET(packet_id);
uint8_t buffer[VC4_HDMI_PACKET_STRIDE];
@@ -623,9 +626,6 @@ static const struct drm_encoder_helper_funcs vc4_hdmi_encoder_helper_funcs = {
/* HDMI audio codec callbacks */
static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 hsm_clock = clk_get_rate(vc4_hdmi->hsm_clock);
unsigned long n, m;
@@ -645,8 +645,6 @@ static void vc4_hdmi_set_n_cts(struct vc4_hdmi *vc4_hdmi)
{
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_crtc *crtc = encoder->crtc;
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
u32 samplerate = vc4_hdmi->audio.samplerate;
u32 n, cts;
@@ -683,7 +681,6 @@ static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_connector *connector = &vc4_hdmi->connector.base;
- struct vc4_dev *vc4 = to_vc4_dev(encoder->dev);
int ret;
if (vc4_hdmi->audio.substream && vc4_hdmi->audio.substream != substream)
@@ -714,9 +711,7 @@ static int vc4_hdmi_audio_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
static void vc4_hdmi_audio_reset(struct vc4_hdmi *vc4_hdmi)
{
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
struct device *dev = &vc4_hdmi->pdev->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
int ret;
ret = vc4_hdmi_stop_packet(encoder, HDMI_INFOFRAME_TYPE_AUDIO);
@@ -747,10 +742,7 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
struct device *dev = &vc4_hdmi->pdev->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 audio_packet_config, channel_mask;
u32 channel_map, i;
@@ -821,8 +813,6 @@ static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
{
struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
switch (cmd) {
case SNDRV_PCM_TRIGGER_START:
@@ -1082,7 +1072,8 @@ static irqreturn_t vc4_cec_irq_handler_thread(int irq, void *priv)
static void vc4_cec_read_msg(struct vc4_dev *vc4, u32 cntrl1)
{
- struct cec_msg *msg = &vc4->hdmi->cec_rx_msg;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct cec_msg *msg = &vc4_hdmi->cec_rx_msg;
unsigned int i;
msg->len = 1 + ((cntrl1 & VC4_HDMI_CEC_REC_WRD_CNT_MASK) >>
@@ -1128,6 +1119,7 @@ static irqreturn_t vc4_cec_irq_handler(int irq, void *priv)
static int vc4_hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
{
struct vc4_dev *vc4 = cec_get_drvdata(adap);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
/* clock period in microseconds */
const u32 usecs = 1000000 / CEC_CLOCK_FREQ;
u32 val = HDMI_READ(VC4_HDMI_CEC_CNTRL_5);
@@ -1171,6 +1163,7 @@ static int vc4_hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
static int vc4_hdmi_cec_adap_log_addr(struct cec_adapter *adap, u8 log_addr)
{
struct vc4_dev *vc4 = cec_get_drvdata(adap);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
HDMI_WRITE(VC4_HDMI_CEC_CNTRL_1,
(HDMI_READ(VC4_HDMI_CEC_CNTRL_1) & ~VC4_HDMI_CEC_ADDR_MASK) |
@@ -1182,6 +1175,7 @@ static int vc4_hdmi_cec_adap_transmit(struct cec_adapter *adap, u8 attempts,
u32 signal_free_time, struct cec_msg *msg)
{
struct vc4_dev *vc4 = cec_get_drvdata(adap);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 val;
unsigned int i;
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
index 17079a39f1b1..cdc9d90f62ac 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -78,9 +78,9 @@ struct vc4_hdmi {
struct debugfs_regset32 hd_regset;
};
-#define HDMI_READ(offset) readl(vc4->hdmi->hdmicore_regs + offset)
-#define HDMI_WRITE(offset, val) writel(val, vc4->hdmi->hdmicore_regs + offset)
-#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
-#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
+#define HDMI_READ(offset) readl(vc4_hdmi->hdmicore_regs + offset)
+#define HDMI_WRITE(offset, val) writel(val, vc4_hdmi->hdmicore_regs + offset)
+#define HD_READ(offset) readl(vc4_hdmi->hd_regs + offset)
+#define HD_WRITE(offset, val) writel(val, vc4_hdmi->hd_regs + offset)
#endif /* _VC4_HDMI_H_ */
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 43/80] drm/vc4: hdmi: Move accessors to vc4_hdmi
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The current driver only supports a single HDMI controller, and part of
the issue is that the main vc4_dev structure holds a pointer to its
(only) HDMI controller, and the HDMI registers accessors will use it to
retrieve the mapped addresses.
Let's modify those accessors to use directly the vc4_hdmi structure so
that we can eventually get rid of that single global pointer.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 22 ++++++++--------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 8 ++++----
2 files changed, 12 insertions(+), 18 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 6733e4bc235b..81c0f67cd0eb 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -123,6 +123,7 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
{
struct drm_device *dev = connector->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
if (vc4->hdmi->hpd_gpio) {
if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
@@ -230,6 +231,7 @@ static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
{
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 packet_id = type - 0x80;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG,
@@ -244,6 +246,7 @@ static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
{
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 packet_id = frame->any.type - 0x80;
u32 packet_reg = VC4_HDMI_RAM_PACKET(packet_id);
uint8_t buffer[VC4_HDMI_PACKET_STRIDE];
@@ -623,9 +626,6 @@ static const struct drm_encoder_helper_funcs vc4_hdmi_encoder_helper_funcs = {
/* HDMI audio codec callbacks */
static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 hsm_clock = clk_get_rate(vc4_hdmi->hsm_clock);
unsigned long n, m;
@@ -645,8 +645,6 @@ static void vc4_hdmi_set_n_cts(struct vc4_hdmi *vc4_hdmi)
{
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_crtc *crtc = encoder->crtc;
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
u32 samplerate = vc4_hdmi->audio.samplerate;
u32 n, cts;
@@ -683,7 +681,6 @@ static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_connector *connector = &vc4_hdmi->connector.base;
- struct vc4_dev *vc4 = to_vc4_dev(encoder->dev);
int ret;
if (vc4_hdmi->audio.substream && vc4_hdmi->audio.substream != substream)
@@ -714,9 +711,7 @@ static int vc4_hdmi_audio_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
static void vc4_hdmi_audio_reset(struct vc4_hdmi *vc4_hdmi)
{
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
struct device *dev = &vc4_hdmi->pdev->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
int ret;
ret = vc4_hdmi_stop_packet(encoder, HDMI_INFOFRAME_TYPE_AUDIO);
@@ -747,10 +742,7 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
struct device *dev = &vc4_hdmi->pdev->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 audio_packet_config, channel_mask;
u32 channel_map, i;
@@ -821,8 +813,6 @@ static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
{
struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
switch (cmd) {
case SNDRV_PCM_TRIGGER_START:
@@ -1082,7 +1072,8 @@ static irqreturn_t vc4_cec_irq_handler_thread(int irq, void *priv)
static void vc4_cec_read_msg(struct vc4_dev *vc4, u32 cntrl1)
{
- struct cec_msg *msg = &vc4->hdmi->cec_rx_msg;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct cec_msg *msg = &vc4_hdmi->cec_rx_msg;
unsigned int i;
msg->len = 1 + ((cntrl1 & VC4_HDMI_CEC_REC_WRD_CNT_MASK) >>
@@ -1128,6 +1119,7 @@ static irqreturn_t vc4_cec_irq_handler(int irq, void *priv)
static int vc4_hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
{
struct vc4_dev *vc4 = cec_get_drvdata(adap);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
/* clock period in microseconds */
const u32 usecs = 1000000 / CEC_CLOCK_FREQ;
u32 val = HDMI_READ(VC4_HDMI_CEC_CNTRL_5);
@@ -1171,6 +1163,7 @@ static int vc4_hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
static int vc4_hdmi_cec_adap_log_addr(struct cec_adapter *adap, u8 log_addr)
{
struct vc4_dev *vc4 = cec_get_drvdata(adap);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
HDMI_WRITE(VC4_HDMI_CEC_CNTRL_1,
(HDMI_READ(VC4_HDMI_CEC_CNTRL_1) & ~VC4_HDMI_CEC_ADDR_MASK) |
@@ -1182,6 +1175,7 @@ static int vc4_hdmi_cec_adap_transmit(struct cec_adapter *adap, u8 attempts,
u32 signal_free_time, struct cec_msg *msg)
{
struct vc4_dev *vc4 = cec_get_drvdata(adap);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 val;
unsigned int i;
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
index 17079a39f1b1..cdc9d90f62ac 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -78,9 +78,9 @@ struct vc4_hdmi {
struct debugfs_regset32 hd_regset;
};
-#define HDMI_READ(offset) readl(vc4->hdmi->hdmicore_regs + offset)
-#define HDMI_WRITE(offset, val) writel(val, vc4->hdmi->hdmicore_regs + offset)
-#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
-#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
+#define HDMI_READ(offset) readl(vc4_hdmi->hdmicore_regs + offset)
+#define HDMI_WRITE(offset, val) writel(val, vc4_hdmi->hdmicore_regs + offset)
+#define HD_READ(offset) readl(vc4_hdmi->hd_regs + offset)
+#define HD_WRITE(offset, val) writel(val, vc4_hdmi->hd_regs + offset)
#endif /* _VC4_HDMI_H_ */
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 43/80] drm/vc4: hdmi: Move accessors to vc4_hdmi
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The current driver only supports a single HDMI controller, and part of
the issue is that the main vc4_dev structure holds a pointer to its
(only) HDMI controller, and the HDMI registers accessors will use it to
retrieve the mapped addresses.
Let's modify those accessors to use directly the vc4_hdmi structure so
that we can eventually get rid of that single global pointer.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 22 ++++++++--------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 8 ++++----
2 files changed, 12 insertions(+), 18 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 6733e4bc235b..81c0f67cd0eb 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -123,6 +123,7 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
{
struct drm_device *dev = connector->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
if (vc4->hdmi->hpd_gpio) {
if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
@@ -230,6 +231,7 @@ static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
{
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 packet_id = type - 0x80;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG,
@@ -244,6 +246,7 @@ static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
{
struct drm_device *dev = encoder->dev;
struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 packet_id = frame->any.type - 0x80;
u32 packet_reg = VC4_HDMI_RAM_PACKET(packet_id);
uint8_t buffer[VC4_HDMI_PACKET_STRIDE];
@@ -623,9 +626,6 @@ static const struct drm_encoder_helper_funcs vc4_hdmi_encoder_helper_funcs = {
/* HDMI audio codec callbacks */
static void vc4_hdmi_audio_set_mai_clock(struct vc4_hdmi *vc4_hdmi)
{
- struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 hsm_clock = clk_get_rate(vc4_hdmi->hsm_clock);
unsigned long n, m;
@@ -645,8 +645,6 @@ static void vc4_hdmi_set_n_cts(struct vc4_hdmi *vc4_hdmi)
{
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_crtc *crtc = encoder->crtc;
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
u32 samplerate = vc4_hdmi->audio.samplerate;
u32 n, cts;
@@ -683,7 +681,6 @@ static int vc4_hdmi_audio_startup(struct snd_pcm_substream *substream,
struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
struct drm_connector *connector = &vc4_hdmi->connector.base;
- struct vc4_dev *vc4 = to_vc4_dev(encoder->dev);
int ret;
if (vc4_hdmi->audio.substream && vc4_hdmi->audio.substream != substream)
@@ -714,9 +711,7 @@ static int vc4_hdmi_audio_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
static void vc4_hdmi_audio_reset(struct vc4_hdmi *vc4_hdmi)
{
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
struct device *dev = &vc4_hdmi->pdev->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
int ret;
ret = vc4_hdmi_stop_packet(encoder, HDMI_INFOFRAME_TYPE_AUDIO);
@@ -747,10 +742,7 @@ static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
- struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
struct device *dev = &vc4_hdmi->pdev->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
u32 audio_packet_config, channel_mask;
u32 channel_map, i;
@@ -821,8 +813,6 @@ static int vc4_hdmi_audio_trigger(struct snd_pcm_substream *substream, int cmd,
{
struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai);
struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base;
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(drm);
switch (cmd) {
case SNDRV_PCM_TRIGGER_START:
@@ -1082,7 +1072,8 @@ static irqreturn_t vc4_cec_irq_handler_thread(int irq, void *priv)
static void vc4_cec_read_msg(struct vc4_dev *vc4, u32 cntrl1)
{
- struct cec_msg *msg = &vc4->hdmi->cec_rx_msg;
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct cec_msg *msg = &vc4_hdmi->cec_rx_msg;
unsigned int i;
msg->len = 1 + ((cntrl1 & VC4_HDMI_CEC_REC_WRD_CNT_MASK) >>
@@ -1128,6 +1119,7 @@ static irqreturn_t vc4_cec_irq_handler(int irq, void *priv)
static int vc4_hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
{
struct vc4_dev *vc4 = cec_get_drvdata(adap);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
/* clock period in microseconds */
const u32 usecs = 1000000 / CEC_CLOCK_FREQ;
u32 val = HDMI_READ(VC4_HDMI_CEC_CNTRL_5);
@@ -1171,6 +1163,7 @@ static int vc4_hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
static int vc4_hdmi_cec_adap_log_addr(struct cec_adapter *adap, u8 log_addr)
{
struct vc4_dev *vc4 = cec_get_drvdata(adap);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
HDMI_WRITE(VC4_HDMI_CEC_CNTRL_1,
(HDMI_READ(VC4_HDMI_CEC_CNTRL_1) & ~VC4_HDMI_CEC_ADDR_MASK) |
@@ -1182,6 +1175,7 @@ static int vc4_hdmi_cec_adap_transmit(struct cec_adapter *adap, u8 attempts,
u32 signal_free_time, struct cec_msg *msg)
{
struct vc4_dev *vc4 = cec_get_drvdata(adap);
+ struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
u32 val;
unsigned int i;
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
index 17079a39f1b1..cdc9d90f62ac 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -78,9 +78,9 @@ struct vc4_hdmi {
struct debugfs_regset32 hd_regset;
};
-#define HDMI_READ(offset) readl(vc4->hdmi->hdmicore_regs + offset)
-#define HDMI_WRITE(offset, val) writel(val, vc4->hdmi->hdmicore_regs + offset)
-#define HD_READ(offset) readl(vc4->hdmi->hd_regs + offset)
-#define HD_WRITE(offset, val) writel(val, vc4->hdmi->hd_regs + offset)
+#define HDMI_READ(offset) readl(vc4_hdmi->hdmicore_regs + offset)
+#define HDMI_WRITE(offset, val) writel(val, vc4_hdmi->hdmicore_regs + offset)
+#define HD_READ(offset) readl(vc4_hdmi->hd_regs + offset)
+#define HD_WRITE(offset, val) writel(val, vc4_hdmi->hd_regs + offset)
#endif /* _VC4_HDMI_H_ */
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 44/80] drm/vc4: hdmi: Use local vc4_hdmi directly
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
The function vc4_hdmi_connector_detect access its vc4_hdmi struct by
dereferencing the pointer in the structure vc4_dev. This will cause some
issues when we will have multiple HDMI controllers, so let's just use the
local variable for now instead of dereferencing that pointer all the time,
and we'll fix the local variable later.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 81c0f67cd0eb..93865327a8d4 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -125,20 +125,20 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
- if (vc4->hdmi->hpd_gpio) {
- if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
- vc4->hdmi->hpd_active_low)
+ if (vc4_hdmi->hpd_gpio) {
+ if (gpio_get_value_cansleep(vc4_hdmi->hpd_gpio) ^
+ vc4_hdmi->hpd_active_low)
return connector_status_connected;
- cec_phys_addr_invalidate(vc4->hdmi->cec_adap);
+ cec_phys_addr_invalidate(vc4_hdmi->cec_adap);
return connector_status_disconnected;
}
- if (drm_probe_ddc(vc4->hdmi->ddc))
+ if (drm_probe_ddc(vc4_hdmi->ddc))
return connector_status_connected;
if (HDMI_READ(VC4_HDMI_HOTPLUG) & VC4_HDMI_HOTPLUG_CONNECTED)
return connector_status_connected;
- cec_phys_addr_invalidate(vc4->hdmi->cec_adap);
+ cec_phys_addr_invalidate(vc4_hdmi->cec_adap);
return connector_status_disconnected;
}
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 44/80] drm/vc4: hdmi: Use local vc4_hdmi directly
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The function vc4_hdmi_connector_detect access its vc4_hdmi struct by
dereferencing the pointer in the structure vc4_dev. This will cause some
issues when we will have multiple HDMI controllers, so let's just use the
local variable for now instead of dereferencing that pointer all the time,
and we'll fix the local variable later.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 81c0f67cd0eb..93865327a8d4 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -125,20 +125,20 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
- if (vc4->hdmi->hpd_gpio) {
- if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
- vc4->hdmi->hpd_active_low)
+ if (vc4_hdmi->hpd_gpio) {
+ if (gpio_get_value_cansleep(vc4_hdmi->hpd_gpio) ^
+ vc4_hdmi->hpd_active_low)
return connector_status_connected;
- cec_phys_addr_invalidate(vc4->hdmi->cec_adap);
+ cec_phys_addr_invalidate(vc4_hdmi->cec_adap);
return connector_status_disconnected;
}
- if (drm_probe_ddc(vc4->hdmi->ddc))
+ if (drm_probe_ddc(vc4_hdmi->ddc))
return connector_status_connected;
if (HDMI_READ(VC4_HDMI_HOTPLUG) & VC4_HDMI_HOTPLUG_CONNECTED)
return connector_status_connected;
- cec_phys_addr_invalidate(vc4->hdmi->cec_adap);
+ cec_phys_addr_invalidate(vc4_hdmi->cec_adap);
return connector_status_disconnected;
}
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 44/80] drm/vc4: hdmi: Use local vc4_hdmi directly
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
The function vc4_hdmi_connector_detect access its vc4_hdmi struct by
dereferencing the pointer in the structure vc4_dev. This will cause some
issues when we will have multiple HDMI controllers, so let's just use the
local variable for now instead of dereferencing that pointer all the time,
and we'll fix the local variable later.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 81c0f67cd0eb..93865327a8d4 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -125,20 +125,20 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
struct vc4_dev *vc4 = to_vc4_dev(dev);
struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
- if (vc4->hdmi->hpd_gpio) {
- if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
- vc4->hdmi->hpd_active_low)
+ if (vc4_hdmi->hpd_gpio) {
+ if (gpio_get_value_cansleep(vc4_hdmi->hpd_gpio) ^
+ vc4_hdmi->hpd_active_low)
return connector_status_connected;
- cec_phys_addr_invalidate(vc4->hdmi->cec_adap);
+ cec_phys_addr_invalidate(vc4_hdmi->cec_adap);
return connector_status_disconnected;
}
- if (drm_probe_ddc(vc4->hdmi->ddc))
+ if (drm_probe_ddc(vc4_hdmi->ddc))
return connector_status_connected;
if (HDMI_READ(VC4_HDMI_HOTPLUG) & VC4_HDMI_HOTPLUG_CONNECTED)
return connector_status_connected;
- cec_phys_addr_invalidate(vc4->hdmi->cec_adap);
+ cec_phys_addr_invalidate(vc4_hdmi->cec_adap);
return connector_status_disconnected;
}
--
git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 45/80] drm/vc4: hdmi: Add container_of macros for encoders and connectors
2020-09-03 8:00 ` Maxime Ripard
(?)
@ 2020-09-03 8:01 ` Maxime Ripard
-1 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, Chanwoo Choi, Hoegeun Kwon,
Stefan Wahren
Whenever the code needs to access the vc4_hdmi structure from a DRM
connector or encoder, it first accesses the drm_device associated to the
connector, then retrieve the drm_dev private data which gives it a
pointer to our vc4_dev, and will finally follow the vc4_hdmi pointer in
that structure.
That will also give us some trouble when having multiple controllers,
but now that we have our encoder and connector structures that are part
of vc4_hdmi, we can simply call container_of on the DRM connector or
encoder and retrieve the vc4_hdmi structure directly.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 41 ++++++++++-------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 16 ++++++++++++++-
2 files changed, 28 insertions(+), 29 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 93865327a8d4..a2053da4e443 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -121,9 +121,7 @@ static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
static enum drm_connector_status
vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
{
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = connector_to_vc4_hdmi(connector);
if (vc4_hdmi->hpd_gpio) {
if (gpio_get_value_cansleep(vc4_hdmi->hpd_gpio) ^
@@ -150,17 +148,13 @@ static void vc4_hdmi_connector_destroy(struct drm_connector *connector)
static int vc4_hdmi_connector_get_modes(struct drm_connector *connector)
{
- struct vc4_hdmi_connector *vc4_connector =
- to_vc4_hdmi_connector(connector);
- struct drm_encoder *encoder = vc4_connector->encoder;
- struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = connector_to_vc4_hdmi(connector);
+ struct vc4_hdmi_encoder *vc4_encoder = &vc4_hdmi->encoder;
int ret = 0;
struct edid *edid;
- edid = drm_get_edid(connector, vc4->hdmi->ddc);
- cec_s_phys_addr_from_edid(vc4->hdmi->cec_adap, edid);
+ edid = drm_get_edid(connector, vc4_hdmi->ddc);
+ cec_s_phys_addr_from_edid(vc4_hdmi->cec_adap, edid);
if (!edid)
return -ENODEV;
@@ -229,9 +223,7 @@ static int vc4_hdmi_connector_init(struct drm_device *dev,
static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
enum hdmi_infoframe_type type)
{
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
u32 packet_id = type - 0x80;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG,
@@ -244,9 +236,7 @@ static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
union hdmi_infoframe *frame)
{
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
u32 packet_id = frame->any.type - 0x80;
u32 packet_reg = VC4_HDMI_RAM_PACKET(packet_id);
uint8_t buffer[VC4_HDMI_PACKET_STRIDE];
@@ -292,9 +282,8 @@ static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
{
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct vc4_dev *vc4 = encoder->dev->dev_private;
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
struct drm_connector *connector = &vc4_hdmi->connector.base;
struct drm_connector_state *cstate = connector->state;
struct drm_crtc *crtc = encoder->crtc;
@@ -338,9 +327,7 @@ static void vc4_hdmi_set_spd_infoframe(struct drm_encoder *encoder)
static void vc4_hdmi_set_audio_infoframe(struct drm_encoder *encoder)
{
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
union hdmi_infoframe frame;
int ret;
@@ -362,9 +349,7 @@ static void vc4_hdmi_set_infoframes(struct drm_encoder *encoder)
static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
{
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
int ret;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG, 0);
@@ -383,10 +368,8 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
{
struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
- struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
+ struct vc4_hdmi_encoder *vc4_encoder = &vc4_hdmi->encoder;
bool debug_dump_regs = false;
bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
index cdc9d90f62ac..749a807cd1f3 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -78,6 +78,22 @@ struct vc4_hdmi {
struct debugfs_regset32 hd_regset;
};
+static inline struct vc4_hdmi *
+connector_to_vc4_hdmi(struct drm_connector *connector)
+{
+ struct vc4_hdmi_connector *_connector = to_vc4_hdmi_connector(connector);
+
+ return container_of(_connector, struct vc4_hdmi, connector);
+}
+
+static inline struct vc4_hdmi *
+encoder_to_vc4_hdmi(struct drm_encoder *encoder)
+{
+ struct vc4_hdmi_encoder *_encoder = to_vc4_hdmi_encoder(encoder);
+
+ return container_of(_encoder, struct vc4_hdmi, encoder);
+}
+
#define HDMI_READ(offset) readl(vc4_hdmi->hdmicore_regs + offset)
#define HDMI_WRITE(offset, val) writel(val, vc4_hdmi->hdmicore_regs + offset)
#define HD_READ(offset) readl(vc4_hdmi->hd_regs + offset)
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 45/80] drm/vc4: hdmi: Add container_of macros for encoders and connectors
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Whenever the code needs to access the vc4_hdmi structure from a DRM
connector or encoder, it first accesses the drm_device associated to the
connector, then retrieve the drm_dev private data which gives it a
pointer to our vc4_dev, and will finally follow the vc4_hdmi pointer in
that structure.
That will also give us some trouble when having multiple controllers,
but now that we have our encoder and connector structures that are part
of vc4_hdmi, we can simply call container_of on the DRM connector or
encoder and retrieve the vc4_hdmi structure directly.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 41 ++++++++++-------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 16 ++++++++++++++-
2 files changed, 28 insertions(+), 29 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 93865327a8d4..a2053da4e443 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -121,9 +121,7 @@ static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
static enum drm_connector_status
vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
{
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = connector_to_vc4_hdmi(connector);
if (vc4_hdmi->hpd_gpio) {
if (gpio_get_value_cansleep(vc4_hdmi->hpd_gpio) ^
@@ -150,17 +148,13 @@ static void vc4_hdmi_connector_destroy(struct drm_connector *connector)
static int vc4_hdmi_connector_get_modes(struct drm_connector *connector)
{
- struct vc4_hdmi_connector *vc4_connector =
- to_vc4_hdmi_connector(connector);
- struct drm_encoder *encoder = vc4_connector->encoder;
- struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = connector_to_vc4_hdmi(connector);
+ struct vc4_hdmi_encoder *vc4_encoder = &vc4_hdmi->encoder;
int ret = 0;
struct edid *edid;
- edid = drm_get_edid(connector, vc4->hdmi->ddc);
- cec_s_phys_addr_from_edid(vc4->hdmi->cec_adap, edid);
+ edid = drm_get_edid(connector, vc4_hdmi->ddc);
+ cec_s_phys_addr_from_edid(vc4_hdmi->cec_adap, edid);
if (!edid)
return -ENODEV;
@@ -229,9 +223,7 @@ static int vc4_hdmi_connector_init(struct drm_device *dev,
static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
enum hdmi_infoframe_type type)
{
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
u32 packet_id = type - 0x80;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG,
@@ -244,9 +236,7 @@ static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
union hdmi_infoframe *frame)
{
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
u32 packet_id = frame->any.type - 0x80;
u32 packet_reg = VC4_HDMI_RAM_PACKET(packet_id);
uint8_t buffer[VC4_HDMI_PACKET_STRIDE];
@@ -292,9 +282,8 @@ static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
{
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct vc4_dev *vc4 = encoder->dev->dev_private;
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
struct drm_connector *connector = &vc4_hdmi->connector.base;
struct drm_connector_state *cstate = connector->state;
struct drm_crtc *crtc = encoder->crtc;
@@ -338,9 +327,7 @@ static void vc4_hdmi_set_spd_infoframe(struct drm_encoder *encoder)
static void vc4_hdmi_set_audio_infoframe(struct drm_encoder *encoder)
{
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
union hdmi_infoframe frame;
int ret;
@@ -362,9 +349,7 @@ static void vc4_hdmi_set_infoframes(struct drm_encoder *encoder)
static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
{
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
int ret;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG, 0);
@@ -383,10 +368,8 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
{
struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
- struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
+ struct vc4_hdmi_encoder *vc4_encoder = &vc4_hdmi->encoder;
bool debug_dump_regs = false;
bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
index cdc9d90f62ac..749a807cd1f3 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -78,6 +78,22 @@ struct vc4_hdmi {
struct debugfs_regset32 hd_regset;
};
+static inline struct vc4_hdmi *
+connector_to_vc4_hdmi(struct drm_connector *connector)
+{
+ struct vc4_hdmi_connector *_connector = to_vc4_hdmi_connector(connector);
+
+ return container_of(_connector, struct vc4_hdmi, connector);
+}
+
+static inline struct vc4_hdmi *
+encoder_to_vc4_hdmi(struct drm_encoder *encoder)
+{
+ struct vc4_hdmi_encoder *_encoder = to_vc4_hdmi_encoder(encoder);
+
+ return container_of(_encoder, struct vc4_hdmi, encoder);
+}
+
#define HDMI_READ(offset) readl(vc4_hdmi->hdmicore_regs + offset)
#define HDMI_WRITE(offset, val) writel(val, vc4_hdmi->hdmicore_regs + offset)
#define HD_READ(offset) readl(vc4_hdmi->hd_regs + offset)
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 342+ messages in thread
* [PATCH v5 45/80] drm/vc4: hdmi: Add container_of macros for encoders and connectors
@ 2020-09-03 8:01 ` Maxime Ripard
0 siblings, 0 replies; 342+ messages in thread
From: Maxime Ripard @ 2020-09-03 8:01 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: Stefan Wahren, Tim Gover, Dave Stevenson, linux-kernel,
dri-devel, Hoegeun Kwon, Chanwoo Choi, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Maxime Ripard
Whenever the code needs to access the vc4_hdmi structure from a DRM
connector or encoder, it first accesses the drm_device associated to the
connector, then retrieve the drm_dev private data which gives it a
pointer to our vc4_dev, and will finally follow the vc4_hdmi pointer in
that structure.
That will also give us some trouble when having multiple controllers,
but now that we have our encoder and connector structures that are part
of vc4_hdmi, we can simply call container_of on the DRM connector or
encoder and retrieve the vc4_hdmi structure directly.
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
drivers/gpu/drm/vc4/vc4_hdmi.c | 41 ++++++++++-------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 16 ++++++++++++++-
2 files changed, 28 insertions(+), 29 deletions(-)
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 93865327a8d4..a2053da4e443 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -121,9 +121,7 @@ static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
static enum drm_connector_status
vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
{
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = connector_to_vc4_hdmi(connector);
if (vc4_hdmi->hpd_gpio) {
if (gpio_get_value_cansleep(vc4_hdmi->hpd_gpio) ^
@@ -150,17 +148,13 @@ static void vc4_hdmi_connector_destroy(struct drm_connector *connector)
static int vc4_hdmi_connector_get_modes(struct drm_connector *connector)
{
- struct vc4_hdmi_connector *vc4_connector =
- to_vc4_hdmi_connector(connector);
- struct drm_encoder *encoder = vc4_connector->encoder;
- struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
+ struct vc4_hdmi *vc4_hdmi = connector_to_vc4_hdmi(connector);
+ struct vc4_hdmi_encoder *vc4_encoder = &vc4_hdmi->encoder;
int ret = 0;
struct edid *edid;
- edid = drm_get_edid(connector, vc4->hdmi->ddc);
- cec_s_phys_addr_from_edid(vc4->hdmi->cec_adap, edid);
+ edid = drm_get_edid(connector, vc4_hdmi->ddc);
+ cec_s_phys_addr_from_edid(vc4_hdmi->cec_adap, edid);
if (!edid)
return -ENODEV;
@@ -229,9 +223,7 @@ static int vc4_hdmi_connector_init(struct drm_device *dev,
static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
enum hdmi_infoframe_type type)
{
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
u32 packet_id = type - 0x80;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG,
@@ -244,9 +236,7 @@ static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
union hdmi_infoframe *frame)
{
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
u32 packet_id = frame->any.type - 0x80;
u32 packet_reg = VC4_HDMI_RAM_PACKET(packet_id);
uint8_t buffer[VC4_HDMI_PACKET_STRIDE];
@@ -292,9 +282,8 @@ static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
{
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct vc4_dev *vc4 = encoder->dev->dev_private;
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
struct drm_connector *connector = &vc4_hdmi->connector.base;
struct drm_connector_state *cstate = connector->state;
struct drm_crtc *crtc = encoder->crtc;
@@ -338,9 +327,7 @@ static void vc4_hdmi_set_spd_infoframe(struct drm_encoder *encoder)
static void vc4_hdmi_set_audio_infoframe(struct drm_encoder *encoder)
{
- struct drm_device *drm = encoder->dev;
- struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
union hdmi_infoframe frame;
int ret;
@@ -362,9 +349,7 @@ static void vc4_hdmi_set_infoframes(struct drm_encoder *encoder)
static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
{
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
int ret;
HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG, 0);
@@ -383,10 +368,8 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
{
struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
- struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_hdmi *vc4_hdmi = vc4->hdmi;
+ struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
+ struct vc4_hdmi_encoder *vc4_encoder = &vc4_hdmi->encoder;
bool debug_dump_regs = false;
bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.h b/drivers/gpu/drm/vc4/vc4_hdmi.h
index cdc9d90f62ac..749a807cd1f3 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.h
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.h
@@ -78,6 +78,22 @@ struct vc4_hdmi {
struct debugfs_regset32 hd_regset;
};
+static inline struct vc4_hdmi *
+connector_to_vc4_hdmi(struct drm_connector *connector)
+{
+ struct vc4_hdmi_connector *_connector = to_vc4_hdmi_connector(connector);
+
+ return container_of(_connector, struct vc4_hdmi, connector);
+}
+
+static inline struct vc4_hdm