[PATCH v3 00/11] arm64: dts: layerscape: update MAC nodes with PHY information

[PATCH v3 00/11] arm64: dts: layerscape: update MAC nodes with PHY information

[Ioana Ciornei]

This patch set aims to add the necessary DTS nodes to complete the
MAC/PCS/PHY representation on DPAA2 devices. The external MDIO bus nodes
and the PHYs found on them are added, along with the PCS MDIO internal
buses and their PCS PHYs. Also, links to these PHYs are added from the
DPMAC node.

Changes in v2:
 - documented the dpmac node into a new yaml entry
 - dropped the '0x' from some unit addresses

Changes in v3:
 - renamed dpmac@x into ethernet@x
 - renamed the new documentation file to use the same name as the
   compatible
 - marked additionalProperties as false
 - added a reference to ethernet-controller.yaml
 - added a new patch to document 10gbase-r - 2/11

Ioana Ciornei (11):
  dt-bindings: net: add the DPAA2 MAC DTS definition
  dt-bindings: net: add the 10gbase-r connection type
  arm64: dts: ls1088a: add external MDIO device nodes
  arm64: dts: ls1088ardb: add QSGMII PHY nodes
  arm64: dts: ls1088ardb: add necessary DTS nodes for DPMAC2
  arm64: dts: ls208xa: add the external MDIO nodes
  arm64: dts: ls2088ardb: add PHY nodes for the CS4340 PHYs
  arm64: dts: ls2088ardb: add PHY nodes for the AQR405 PHYs
  arm64: dts: ls208xa: add PCS MDIO and PCS PHY nodes
  arm64: dts: lx2160a: add PCS MDIO and PCS PHY nodes
  arm64: dts: lx2160ardb: add nodes for the AQR107 PHYs

 .../bindings/net/ethernet-controller.yaml     |   1 +
 .../bindings/net/fsl,qoriq-mc-dpmac.yaml      |  60 ++++
 .../boot/dts/freescale/fsl-ls1088a-rdb.dts    | 119 ++++++++
 .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 101 +++++-
 .../boot/dts/freescale/fsl-ls2088a-rdb.dts    | 118 +++++++
 .../arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 274 ++++++++++++++++-
 .../boot/dts/freescale/fsl-lx2160a-rdb.dts    |  32 ++
 .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 288 ++++++++++++++++--
 8 files changed, 949 insertions(+), 44 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml

-- 
2.28.0

[PATCH v3 01/11] dt-bindings: net: add the DPAA2 MAC DTS definition

[Ioana Ciornei]

Add a documentation entry for the DTS bindings needed and supported by
the dpaa2-mac driver.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - new patch
Changes in v3:
 - renamed dpmac@x into ethernet@x
 - renamed the new documentation file to use the same name as the
   compatible
 - marked additionalProperties as false
 - added a reference to ethernet-controller.yaml

 .../bindings/net/fsl,qoriq-mc-dpmac.yaml      | 60 +++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml

diff --git a/Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml b/Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml
new file mode 100644
index 000000000000..2159b7d1f537
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/fsl,qoriq-mc-dpmac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: DPAA2 MAC bindings
+
+maintainers:
+  - Ioana Ciornei <ioana.ciornei@nxp.com>
+
+description:
+  This binding represents the DPAA2 MAC objects found on the fsl-mc bus and
+  located under the 'dpmacs' node for the fsl-mc bus DTS node.
+
+allOf:
+  - $ref: "ethernet-controller.yaml#"
+
+properties:
+  compatible:
+    const: fsl,qoriq-mc-dpmac
+
+  reg:
+    maxItems: 1
+    description: The DPMAC number
+
+  phy-handle: true
+
+  phy-connection-type: true
+
+  phy-mode: true
+
+  pcs-handle:
+    $ref: /schemas/types.yaml#definitions/phandle
+    description:
+      A reference to a node representing a PCS PHY device found on
+      the internal MDIO bus.
+
+  managed: true
+
+required:
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    dpmacs {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      ethernet@4 {
+        compatible = "fsl,qoriq-mc-dpmac";
+        reg = <0x4>;
+        phy-handle = <&mdio1_phy6>;
+        phy-connection-type = "qsgmii";
+        managed = "in-band-status";
+        pcs-handle = <&pcs3_1>;
+      };
+    };
-- 
2.28.0

[PATCH v3 02/11] dt-bindings: net: add the 10gbase-r connection type

[Ioana Ciornei]

Add 10gbase-r to the list of accepted PHY connection types between an
Ethernet device and a physical PHY. This is available as a valid
connection type since commit c114574ebfdf ("net: phy: add
PHY_INTERFACE_MODE_10GBASER")

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v3:
 -  new patch

 Documentation/devicetree/bindings/net/ethernet-controller.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/net/ethernet-controller.yaml b/Documentation/devicetree/bindings/net/ethernet-controller.yaml
index 137fbb95c0ea..75f9155ce161 100644
--- a/Documentation/devicetree/bindings/net/ethernet-controller.yaml
+++ b/Documentation/devicetree/bindings/net/ethernet-controller.yaml
@@ -95,6 +95,7 @@ properties:
       # 10GBASE-KR, XFI, SFI
       - 10gbase-kr
       - usxgmii
+      - 10gbase-r
 
   phy-mode:
     $ref: "#/properties/phy-connection-type"
-- 
2.28.0

[PATCH v3 03/11] arm64: dts: ls1088a: add external MDIO device nodes

[Ioana Ciornei]

Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - removed the 0x from the unit addresses
Changes in v3:
 - none

 arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index 169f4742ae3b..421ff19f02c9 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -654,6 +654,24 @@ ptp-timer@8b95000 {
 			fsl,extts-fifo;
 		};
 
+		emdio1: mdio@8b96000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8B96000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		emdio2: mdio@8b97000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8B97000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		cluster1_core0_watchdog: wdt@c000000 {
 			compatible = "arm,sp805-wdt", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
-- 
2.28.0

[PATCH v3 04/11] arm64: dts: ls1088ardb: add QSGMII PHY nodes

[Ioana Ciornei]

Annotate the external MDIO1 node and describe the 8 QSGMII PHYs found on
the LS1088ARDB board and add phy-handles for DPMACs 3-10 to its
associated PHY.  Also, add the internal PCS MDIO nodes for the internal
MDIO buses found on the LS1088A SoC along with their internal PCS PHY
and link the corresponding DPMAC to the PCS through the pcs-handle.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - none
Changes in v3:
 - renamed dpmac@x into ethernet@x

 .../boot/dts/freescale/fsl-ls1088a-rdb.dts    | 100 ++++++++++++++++++
 .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi |  70 ++++++++++--
 2 files changed, 160 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
index 5633e59febc3..d7886b084f7f 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
@@ -17,6 +17,98 @@ / {
 	compatible = "fsl,ls1088a-rdb", "fsl,ls1088a";
 };
 
+&dpmac3 {
+	phy-handle = <&mdio1_phy5>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	pcs-handle = <&pcs3_0>;
+};
+
+&dpmac4 {
+	phy-handle = <&mdio1_phy6>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	pcs-handle = <&pcs3_1>;
+};
+
+&dpmac5 {
+	phy-handle = <&mdio1_phy7>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	pcs-handle = <&pcs3_2>;
+};
+
+&dpmac6 {
+	phy-handle = <&mdio1_phy8>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	pcs-handle = <&pcs3_3>;
+};
+
+&dpmac7 {
+	phy-handle = <&mdio1_phy1>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	pcs-handle = <&pcs7_0>;
+};
+
+&dpmac8 {
+	phy-handle = <&mdio1_phy2>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	pcs-handle = <&pcs7_1>;
+};
+
+&dpmac9 {
+	phy-handle = <&mdio1_phy3>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	pcs-handle = <&pcs7_2>;
+};
+
+&dpmac10 {
+	phy-handle = <&mdio1_phy4>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	pcs-handle = <&pcs7_3>;
+};
+
+&emdio1 {
+	status = "okay";
+
+	mdio1_phy1: emdio1_phy@1 {
+		reg = <0x1c>;
+	};
+
+	mdio1_phy2: emdio1_phy@2 {
+		reg = <0x1d>;
+	};
+
+	mdio1_phy3: emdio1_phy@3 {
+		reg = <0x1e>;
+	};
+
+	mdio1_phy4: emdio1_phy@4 {
+		reg = <0x1f>;
+	};
+
+	mdio1_phy5: emdio1_phy@5 {
+		reg = <0x0c>;
+	};
+
+	mdio1_phy6: emdio1_phy@6 {
+		reg = <0x0d>;
+	};
+
+	mdio1_phy7: emdio1_phy@7 {
+		reg = <0x0e>;
+	};
+
+	mdio1_phy8: emdio1_phy@8 {
+		reg = <0x0f>;
+	};
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -87,6 +179,14 @@ &esdhc {
 	status = "okay";
 };
 
+&pcs_mdio3 {
+	status = "okay";
+};
+
+&pcs_mdio7 {
+	status = "okay";
+};
+
 &qspi {
 	status = "okay";
 
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index 421ff19f02c9..43a14bbfe59c 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -672,6 +672,56 @@ emdio2: mdio@8b97000 {
 			status = "disabled";
 		};
 
+		pcs_mdio3: mdio@8c0f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c0f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs3_0: pcs-phy@0 {
+				reg = <0>;
+			};
+
+			pcs3_1: pcs-phy@1 {
+				reg = <1>;
+			};
+
+			pcs3_2: pcs-phy@2 {
+				reg = <2>;
+			};
+
+			pcs3_3: pcs-phy@3 {
+				reg = <3>;
+			};
+		};
+
+		pcs_mdio7: mdio@8c1f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c1f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs7_0: pcs-phy@0 {
+				reg = <0>;
+			};
+
+			pcs7_1: pcs-phy@1 {
+				reg = <1>;
+			};
+
+			pcs7_2: pcs-phy@2 {
+				reg = <2>;
+			};
+
+			pcs7_3: pcs-phy@3 {
+				reg = <3>;
+			};
+		};
+
 		cluster1_core0_watchdog: wdt@c000000 {
 			compatible = "arm,sp805-wdt", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
@@ -749,52 +799,52 @@ dpmacs {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				dpmac1: dpmac@1 {
+				dpmac1: ethernet@1 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <1>;
 				};
 
-				dpmac2: dpmac@2 {
+				dpmac2: ethernet@2 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <2>;
 				};
 
-				dpmac3: dpmac@3 {
+				dpmac3: ethernet@3 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <3>;
 				};
 
-				dpmac4: dpmac@4 {
+				dpmac4: ethernet@4 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <4>;
 				};
 
-				dpmac5: dpmac@5 {
+				dpmac5: ethernet@5 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <5>;
 				};
 
-				dpmac6: dpmac@6 {
+				dpmac6: ethernet@6 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <6>;
 				};
 
-				dpmac7: dpmac@7 {
+				dpmac7: ethernet@7 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <7>;
 				};
 
-				dpmac8: dpmac@8 {
+				dpmac8: ethernet@8 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <8>;
 				};
 
-				dpmac9: dpmac@9 {
+				dpmac9: ethernet@9 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <9>;
 				};
 
-				dpmac10: dpmac@a {
+				dpmac10: ethernet@a {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xa>;
 				};
-- 
2.28.0

[PATCH v3 05/11] arm64: dts: ls1088ardb: add necessary DTS nodes for DPMAC2

[Ioana Ciornei]

Annotate the external MDIO2 node and describe the 10GBASER PHY found on
the LS1088ARDB board and add a phy-handle for DPMAC2 to link it.
Also, add the internal PCS MDIO node for the internal MDIO buses found
on the LS1088A SoC along with its internal PCS PHY and link the
corresponding DPMAC to the PCS through the pcs-handle.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - none
Changes in v3:
 - none

 .../boot/dts/freescale/fsl-ls1088a-rdb.dts    | 19 +++++++++++++++++++
 .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 13 +++++++++++++
 2 files changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
index d7886b084f7f..661898064f0c 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
@@ -17,6 +17,12 @@ / {
 	compatible = "fsl,ls1088a-rdb", "fsl,ls1088a";
 };
 
+&dpmac2 {
+	phy-handle = <&mdio2_aquantia_phy>;
+	phy-connection-type = "10gbase-r";
+	pcs-handle = <&pcs2>;
+};
+
 &dpmac3 {
 	phy-handle = <&mdio1_phy5>;
 	phy-connection-type = "qsgmii";
@@ -109,6 +115,15 @@ mdio1_phy8: emdio1_phy@8 {
 	};
 };
 
+&emdio2 {
+	status = "okay";
+
+	mdio2_aquantia_phy: emdio2_aquantia@0 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x0>;
+	};
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -179,6 +194,10 @@ &esdhc {
 	status = "okay";
 };
 
+&pcs_mdio2 {
+	status = "okay";
+};
+
 &pcs_mdio3 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index 43a14bbfe59c..52c3a1ac6b69 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -672,6 +672,19 @@ emdio2: mdio@8b97000 {
 			status = "disabled";
 		};
 
+		pcs_mdio2: mdio@8c0b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c0b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs2: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
 		pcs_mdio3: mdio@8c0f000 {
 			compatible = "fsl,fman-memac-mdio";
 			reg = <0x0 0x8c0f000 0x0 0x1000>;
-- 
2.28.0

[PATCH v3 06/11] arm64: dts: ls208xa: add the external MDIO nodes

[Ioana Ciornei]

Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - removed the 0x from the unit addresses
Changes in v3:
 - none

 arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index 41102dacc2e1..22607096b5b9 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -335,6 +335,24 @@ ptp-timer@8b95000 {
 			fsl,extts-fifo;
 		};
 
+		emdio1: mdio@8b96000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8B96000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		emdio2: mdio@8b97000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8B97000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		fsl_mc: fsl-mc@80c000000 {
 			compatible = "fsl,qoriq-mc";
 			reg = <0x00000008 0x0c000000 0 0x40>,	 /* MC portal base */
-- 
2.28.0

[PATCH v3 07/11] arm64: dts: ls2088ardb: add PHY nodes for the CS4340 PHYs

[Ioana Ciornei]

Annotate the EMDIO1 node and describe the 4 10GBASER PHYs found on the
LS2088ARDB board. Also, add phy-handles for DPMACs 1-4 to their
associated PHY.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - none
Changes in v3:
 - none

 .../boot/dts/freescale/fsl-ls2088a-rdb.dts    | 41 +++++++++++++++++++
 1 file changed, 41 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
index f6b4d75a258b..0d1935fcd201 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
@@ -22,3 +22,44 @@ chosen {
 		stdout-path = "serial1:115200n8";
 	};
 };
+
+&dpmac1 {
+	phy-handle = <&mdio1_phy1>;
+};
+
+&dpmac2 {
+	phy-handle = <&mdio1_phy2>;
+};
+
+&dpmac3 {
+	phy-handle = <&mdio1_phy3>;
+};
+
+&dpmac4 {
+	phy-handle = <&mdio1_phy4>;
+};
+
+&emdio1 {
+	status = "okay";
+
+	mdio1_phy1: emdio1_phy@1 {
+		compatible = "ethernet-phy-id13e5.1002";
+		reg = <0x10>;
+		phy-connection-type = "10gbase-r";
+	};
+	mdio1_phy2: emdio1_phy@2 {
+		compatible = "ethernet-phy-id13e5.1002";
+		reg = <0x11>;
+		phy-connection-type = "10gbase-r";
+	};
+	mdio1_phy3: emdio1_phy@3 {
+		compatible = "ethernet-phy-id13e5.1002";
+		reg = <0x12>;
+		phy-connection-type = "10gbase-r";
+	};
+	mdio1_phy4: emdio1_phy@4 {
+		compatible = "ethernet-phy-id13e5.1002";
+		reg = <0x13>;
+		phy-connection-type = "10gbase-r";
+	};
+};
-- 
2.28.0

[PATCH v3 08/11] arm64: dts: ls2088ardb: add PHY nodes for the AQR405 PHYs

[Ioana Ciornei]

Annotate the EMDIO2 node and describe the other 4 10GBASER PHYs found on
the LS2088ARDB board. Also, add phy-handles for DPMACs 5-8 to their
associated PHY.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - none
Changes in v3:
 - none


 .../boot/dts/freescale/fsl-ls2088a-rdb.dts    | 45 +++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
index 0d1935fcd201..0492c9f76490 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
@@ -39,6 +39,22 @@ &dpmac4 {
 	phy-handle = <&mdio1_phy4>;
 };
 
+&dpmac5 {
+	phy-handle = <&mdio2_phy1>;
+};
+
+&dpmac6 {
+	phy-handle = <&mdio2_phy2>;
+};
+
+&dpmac7 {
+	phy-handle = <&mdio2_phy3>;
+};
+
+&dpmac8 {
+	phy-handle = <&mdio2_phy4>;
+};
+
 &emdio1 {
 	status = "okay";
 
@@ -63,3 +79,32 @@ mdio1_phy4: emdio1_phy@4 {
 		phy-connection-type = "10gbase-r";
 	};
 };
+
+&emdio2 {
+	status = "okay";
+
+	mdio2_phy1: emdio2_phy@1 {
+		compatible = "ethernet-phy-id03a1.b4b0", "ethernet-phy-ieee802.3-c45";
+		interrupts = <0 1 0x4>;
+		reg = <0x0>;
+		phy-connection-type = "10gbase-r";
+	};
+	mdio2_phy2: emdio2_phy@2 {
+		compatible = "ethernet-phy-id03a1.b4b0", "ethernet-phy-ieee802.3-c45";
+		interrupts = <0 2 0x4>;
+		reg = <0x1>;
+		phy-connection-type = "10gbase-r";
+	};
+	mdio2_phy3: emdio2_phy@3 {
+		compatible = "ethernet-phy-id03a1.b4b0", "ethernet-phy-ieee802.3-c45";
+		interrupts = <0 4 0x4>;
+		reg = <0x2>;
+		phy-connection-type = "10gbase-r";
+	};
+	mdio2_phy4: emdio2_phy@4 {
+		compatible = "ethernet-phy-id03a1.b4b0", "ethernet-phy-ieee802.3-c45";
+		interrupts = <0 5 0x4>;
+		reg = <0x3>;
+		phy-connection-type = "10gbase-r";
+	};
+};
-- 
2.28.0

[PATCH v3 09/11] arm64: dts: ls208xa: add PCS MDIO and PCS PHY nodes

[Ioana Ciornei]

Add PCS MDIO nodes for the internal MDIO buses on the LS208x SoCs, along
with their internal PCS PHYs which will be used when the DPMAC object is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - none
Changes in v3:
 - renamed dpmac@x into ethernet@x

 .../boot/dts/freescale/fsl-ls2088a-rdb.dts    |  32 +++
 .../arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 256 ++++++++++++++++--
 2 files changed, 272 insertions(+), 16 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
index 0492c9f76490..20e14d1a3caa 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
@@ -108,3 +108,35 @@ mdio2_phy4: emdio2_phy@4 {
 		phy-connection-type = "10gbase-r";
 	};
 };
+
+&pcs_mdio1 {
+	status = "okay";
+};
+
+&pcs_mdio2 {
+	status = "okay";
+};
+
+&pcs_mdio3 {
+	status = "okay";
+};
+
+&pcs_mdio4 {
+	status = "okay";
+};
+
+&pcs_mdio5 {
+	status = "okay";
+};
+
+&pcs_mdio6 {
+	status = "okay";
+};
+
+&pcs_mdio7 {
+	status = "okay";
+};
+
+&pcs_mdio8 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index 22607096b5b9..bb6cf1b3447b 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -353,6 +353,214 @@ emdio2: mdio@8b97000 {
 			status = "disabled";
 		};
 
+		pcs_mdio1: mdio@8c07000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c07000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs1: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio2: mdio@8c0b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c0b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs2: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio3: mdio@8c0f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c0f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs3: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio4: mdio@8c13000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c13000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs4: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio5: mdio@8c17000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c17000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs5: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio6: mdio@8c1b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c1b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs6: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio7: mdio@8c1f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c1f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs7: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio8: mdio@8c23000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c23000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs8: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio9: mdio@8c27000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c27000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs9: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio10: mdio@8c2b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c2b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs10: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio11: mdio@8c2f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c2f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs11: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio12: mdio@8c33000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c33000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs12: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio13: mdio@8c37000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c37000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs13: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio14: mdio@8c3b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c3b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs14: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio15: mdio@8c3f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c3f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs15: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio16: mdio@8c43000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c43000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs16: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
 		fsl_mc: fsl-mc@80c000000 {
 			compatible = "fsl,qoriq-mc";
 			reg = <0x00000008 0x0c000000 0 0x40>,	 /* MC portal base */
@@ -377,84 +585,100 @@ dpmacs {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				dpmac1: dpmac@1 {
+				dpmac1: ethernet@1 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x1>;
+					pcs-handle = <&pcs1>;
 				};
 
-				dpmac2: dpmac@2 {
+				dpmac2: ethernet@2 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x2>;
+					pcs-handle = <&pcs2>;
 				};
 
-				dpmac3: dpmac@3 {
+				dpmac3: ethernet@3 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x3>;
+					pcs-handle = <&pcs3>;
 				};
 
-				dpmac4: dpmac@4 {
+				dpmac4: ethernet@4 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x4>;
+					pcs-handle = <&pcs4>;
 				};
 
-				dpmac5: dpmac@5 {
+				dpmac5: ethernet@5 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x5>;
+					pcs-handle = <&pcs5>;
 				};
 
-				dpmac6: dpmac@6 {
+				dpmac6: ethernet@6 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x6>;
+					pcs-handle = <&pcs6>;
 				};
 
-				dpmac7: dpmac@7 {
+				dpmac7: ethernet@7 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x7>;
+					pcs-handle = <&pcs7>;
 				};
 
-				dpmac8: dpmac@8 {
+				dpmac8: ethernet@8 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x8>;
+					pcs-handle = <&pcs8>;
 				};
 
-				dpmac9: dpmac@9 {
+				dpmac9: ethernet@9 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x9>;
+					pcs-handle = <&pcs9>;
 				};
 
-				dpmac10: dpmac@a {
+				dpmac10: ethernet@a {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xa>;
+					pcs-handle = <&pcs10>;
 				};
 
-				dpmac11: dpmac@b {
+				dpmac11: ethernet@b {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xb>;
+					pcs-handle = <&pcs11>;
 				};
 
-				dpmac12: dpmac@c {
+				dpmac12: ethernet@c {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xc>;
+					pcs-handle = <&pcs12>;
 				};
 
-				dpmac13: dpmac@d {
+				dpmac13: ethernet@d {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xd>;
+					pcs-handle = <&pcs13>;
 				};
 
-				dpmac14: dpmac@e {
+				dpmac14: ethernet@e {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xe>;
+					pcs-handle = <&pcs14>;
 				};
 
-				dpmac15: dpmac@f {
+				dpmac15: ethernet@f {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xf>;
+					pcs-handle = <&pcs15>;
 				};
 
-				dpmac16: dpmac@10 {
+				dpmac16: ethernet@10 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x10>;
+					pcs-handle = <&pcs16>;
 				};
 			};
 		};
-- 
2.28.0

[PATCH v3 10/11] arm64: dts: lx2160a: add PCS MDIO and PCS PHY nodes

[Ioana Ciornei]

Add PCS MDIO nodes for the internal MDIO buses on the LX2160A, along
with their internal PCS PHYs, which will be used when the DPMAC is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - none
Changes in v3:
 - renamed dpmac@x into ethernet@x

 .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 288 ++++++++++++++++--
 1 file changed, 270 insertions(+), 18 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
index d247e4228d60..010e7d8619e5 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -1305,6 +1305,240 @@ emdio2: mdio@8b97000 {
 			status = "disabled";
 		};
 
+		pcs_mdio1: mdio@8c07000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c07000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs1: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio2: mdio@8c0b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c0b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs2: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio3: mdio@8c0f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c0f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs3: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio4: mdio@8c13000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c13000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs4: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio5: mdio@8c17000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c17000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs5: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio6: mdio@8c1b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c1b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs6: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio7: mdio@8c1f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c1f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs7: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio8: mdio@8c23000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c23000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs8: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio9: mdio@8c27000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c27000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs9: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio10: mdio@8c2b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c2b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs10: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio11: mdio@8c2f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c2f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs11: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio12: mdio@8c33000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c33000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs12: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio13: mdio@8c37000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c37000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs13: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio14: mdio@8c3b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c3b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs14: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio15: mdio@8c3f000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c3f000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs15: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio16: mdio@8c43000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c43000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs16: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio17: mdio@8c47000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c47000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs17: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
+		pcs_mdio18: mdio@8c4b000 {
+			compatible = "fsl,fman-memac-mdio";
+			reg = <0x0 0x8c4b000 0x0 0x1000>;
+			little-endian;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			pcs18: pcs-phy@0 {
+				reg = <0>;
+			};
+		};
+
 		fsl_mc: fsl-mc@80c000000 {
 			compatible = "fsl,qoriq-mc";
 			reg = <0x00000008 0x0c000000 0 0x40>,
@@ -1330,94 +1564,112 @@ dpmacs {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				dpmac1: dpmac@1 {
+				dpmac1: ethernet@1 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x1>;
+					pcs-handle = <&pcs1>;
 				};
 
-				dpmac2: dpmac@2 {
+				dpmac2: ethernet@2 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x2>;
+					pcs-handle = <&pcs2>;
 				};
 
-				dpmac3: dpmac@3 {
+				dpmac3: ethernet@3 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x3>;
+					pcs-handle = <&pcs3>;
 				};
 
-				dpmac4: dpmac@4 {
+				dpmac4: ethernet@4 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x4>;
+					pcs-handle = <&pcs4>;
 				};
 
-				dpmac5: dpmac@5 {
+				dpmac5: ethernet@5 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x5>;
+					pcs-handle = <&pcs5>;
 				};
 
-				dpmac6: dpmac@6 {
+				dpmac6: ethernet@6 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x6>;
+					pcs-handle = <&pcs6>;
 				};
 
-				dpmac7: dpmac@7 {
+				dpmac7: ethernet@7 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x7>;
+					pcs-handle = <&pcs7>;
 				};
 
-				dpmac8: dpmac@8 {
+				dpmac8: ethernet@8 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x8>;
+					pcs-handle = <&pcs8>;
 				};
 
-				dpmac9: dpmac@9 {
+				dpmac9: ethernet@9 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x9>;
+					pcs-handle = <&pcs9>;
 				};
 
-				dpmac10: dpmac@a {
+				dpmac10: ethernet@a {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xa>;
+					pcs-handle = <&pcs10>;
 				};
 
-				dpmac11: dpmac@b {
+				dpmac11: ethernet@b {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xb>;
+					pcs-handle = <&pcs11>;
 				};
 
-				dpmac12: dpmac@c {
+				dpmac12: ethernet@c {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xc>;
+					pcs-handle = <&pcs12>;
 				};
 
-				dpmac13: dpmac@d {
+				dpmac13: ethernet@d {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xd>;
+					pcs-handle = <&pcs13>;
 				};
 
-				dpmac14: dpmac@e {
+				dpmac14: ethernet@e {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xe>;
+					pcs-handle = <&pcs14>;
 				};
 
-				dpmac15: dpmac@f {
+				dpmac15: ethernet@f {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0xf>;
+					pcs-handle = <&pcs15>;
 				};
 
-				dpmac16: dpmac@10 {
+				dpmac16: ethernet@10 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x10>;
+					pcs-handle = <&pcs16>;
 				};
 
-				dpmac17: dpmac@11 {
+				dpmac17: ethernet@11 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x11>;
+					pcs-handle = <&pcs17>;
 				};
 
-				dpmac18: dpmac@12 {
+				dpmac18: ethernet@12 {
 					compatible = "fsl,qoriq-mc-dpmac";
 					reg = <0x12>;
+					pcs-handle = <&pcs18>;
 				};
 			};
 		};
-- 
2.28.0

[PATCH v3 11/11] arm64: dts: lx2160ardb: add nodes for the AQR107 PHYs

[Ioana Ciornei]

Annotate the EMDIO1 node and describe the 2 AQR107 PHYs found on the
LX2160ARDB board. Also, add the necessary phy-handles for DPMACs 3 and 4
to their associated PHY.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
---
Changes in v2:
 - none
Changes in v3:
 - none

 .../boot/dts/freescale/fsl-lx2160a-rdb.dts    | 32 +++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
index 54fe8cd3a711..7723ad5efd37 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
@@ -35,6 +35,18 @@ &crypto {
 	status = "okay";
 };
 
+&dpmac3 {
+	phy-handle = <&aquantia_phy1>;
+	phy-connection-type = "usxgmii";
+	managed = "in-band-status";
+};
+
+&dpmac4 {
+	phy-handle = <&aquantia_phy2>;
+	phy-connection-type = "usxgmii";
+	managed = "in-band-status";
+};
+
 &dpmac17 {
 	phy-handle = <&rgmii_phy1>;
 	phy-connection-type = "rgmii-id";
@@ -61,6 +73,18 @@ rgmii_phy2: ethernet-phy@2 {
 		reg = <0x2>;
 		eee-broken-1000t;
 	};
+
+	aquantia_phy1: ethernet-phy@4 {
+		/* AQR107 PHY */
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x4>;
+	};
+
+	aquantia_phy2: ethernet-phy@5 {
+		/* AQR107 PHY */
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x5>;
+	};
 };
 
 &esdhc0 {
@@ -156,6 +180,14 @@ rtc@51 {
 	};
 };
 
+&pcs_mdio3 {
+	status = "okay";
+};
+
+&pcs_mdio4 {
+	status = "okay";
+};
+
 &sata0 {
 	status = "okay";
 };
-- 
2.28.0

Re: [PATCH v3 01/11] dt-bindings: net: add the DPAA2 MAC DTS definition

[Rob Herring]

On Wed, 07 Oct 2020 23:39:26 +0300, Ioana Ciornei wrote:
> Add a documentation entry for the DTS bindings needed and supported by
> the dpaa2-mac driver.
> 
> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
> ---
> Changes in v2:
>  - new patch
> Changes in v3:
>  - renamed dpmac@x into ethernet@x
>  - renamed the new documentation file to use the same name as the
>    compatible
>  - marked additionalProperties as false
>  - added a reference to ethernet-controller.yaml
> 
>  .../bindings/net/fsl,qoriq-mc-dpmac.yaml      | 60 +++++++++++++++++++
>  1 file changed, 60 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 02/11] dt-bindings: net: add the 10gbase-r connection type

[Rob Herring]

On Wed, 07 Oct 2020 23:39:27 +0300, Ioana Ciornei wrote:
> Add 10gbase-r to the list of accepted PHY connection types between an
> Ethernet device and a physical PHY. This is available as a valid
> connection type since commit c114574ebfdf ("net: phy: add
> PHY_INTERFACE_MODE_10GBASER")
> 
> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
> ---
> Changes in v3:
>  -  new patch
> 
>  Documentation/devicetree/bindings/net/ethernet-controller.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 01/11] dt-bindings: net: add the DPAA2 MAC DTS definition

[Ioana Ciornei]

On Tue, Oct 13, 2020 at 08:31:32AM -0500, Rob Herring wrote:
> On Wed, 07 Oct 2020 23:39:26 +0300, Ioana Ciornei wrote:
> > Add a documentation entry for the DTS bindings needed and supported by
> > the dpaa2-mac driver.
> > 
> > Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
> > ---
> > Changes in v2:
> >  - new patch
> > Changes in v3:
> >  - renamed dpmac@x into ethernet@x
> >  - renamed the new documentation file to use the same name as the
> >    compatible
> >  - marked additionalProperties as false
> >  - added a reference to ethernet-controller.yaml
> > 
> >  .../bindings/net/fsl,qoriq-mc-dpmac.yaml      | 60 +++++++++++++++++++
> >  1 file changed, 60 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml
> > 
> 
> Reviewed-by: Rob Herring <robh@kernel.org>

Thanks for the review.

Is this going in 5.10 by any chance or should I resend these after
the merge window with the reviewed-by tags?

Ioana

Re: [PATCH v3 01/11] dt-bindings: net: add the DPAA2 MAC DTS definition

[Rob Herring]

On Tue, Oct 13, 2020 at 9:19 AM Ioana Ciornei <ioana.ciornei@nxp.com> wrote:
>
> On Tue, Oct 13, 2020 at 08:31:32AM -0500, Rob Herring wrote:
> > On Wed, 07 Oct 2020 23:39:26 +0300, Ioana Ciornei wrote:
> > > Add a documentation entry for the DTS bindings needed and supported by
> > > the dpaa2-mac driver.
> > >
> > > Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
> > > ---
> > > Changes in v2:
> > >  - new patch
> > > Changes in v3:
> > >  - renamed dpmac@x into ethernet@x
> > >  - renamed the new documentation file to use the same name as the
> > >    compatible
> > >  - marked additionalProperties as false
> > >  - added a reference to ethernet-controller.yaml
> > >
> > >  .../bindings/net/fsl,qoriq-mc-dpmac.yaml      | 60 +++++++++++++++++++
> > >  1 file changed, 60 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml
> > >
> >
> > Reviewed-by: Rob Herring <robh@kernel.org>
>
> Thanks for the review.
>
> Is this going in 5.10 by any chance or should I resend these after
> the merge window with the reviewed-by tags?

I just noticed you didn't Cc netdev as I would expect this to go via
the networking tree. So yes, resend after the merge window.

Rob

Re: [PATCH v3 01/11] dt-bindings: net: add the DPAA2 MAC DTS definition

[Ioana Ciornei]

On Tue, Oct 13, 2020 at 12:21:53PM -0500, Rob Herring wrote:
> On Tue, Oct 13, 2020 at 9:19 AM Ioana Ciornei <ioana.ciornei@nxp.com> wrote:
> >
> > On Tue, Oct 13, 2020 at 08:31:32AM -0500, Rob Herring wrote:
> > > On Wed, 07 Oct 2020 23:39:26 +0300, Ioana Ciornei wrote:
> > > > Add a documentation entry for the DTS bindings needed and supported by
> > > > the dpaa2-mac driver.
> > > >
> > > > Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
> > > > ---
> > > > Changes in v2:
> > > >  - new patch
> > > > Changes in v3:
> > > >  - renamed dpmac@x into ethernet@x
> > > >  - renamed the new documentation file to use the same name as the
> > > >    compatible
> > > >  - marked additionalProperties as false
> > > >  - added a reference to ethernet-controller.yaml
> > > >
> > > >  .../bindings/net/fsl,qoriq-mc-dpmac.yaml      | 60 +++++++++++++++++++
> > > >  1 file changed, 60 insertions(+)
> > > >  create mode 100644 Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml
> > > >
> > >
> > > Reviewed-by: Rob Herring <robh@kernel.org>
> >
> > Thanks for the review.
> >
> > Is this going in 5.10 by any chance or should I resend these after
> > the merge window with the reviewed-by tags?
> 
> I just noticed you didn't Cc netdev as I would expect this to go via
> the networking tree. So yes, resend after the merge window.
> 

David said to an earlier version of this patch set that he would not
want to pick this up through net-next since it's a sizable change and
this should go through the devicetree trees.
https://lore.kernel.org/netdev/20201002.161318.726844448692603677.davem@davemloft.net/

This is why I didn't cc again the netdev.

Ioana