[PATCH v1] imx: support i.MX8QM DMSSE20 a1 board

* [PATCH v1] imx: support i.MX8QM DMSSE20 a1 board
@ 2020-08-31 14:54 Oliver Graute
  2020-08-31 16:17 ` Tom Rini
  2020-08-31 21:48 ` Fabio Estevam
  0 siblings, 2 replies; 5+ messages in thread
From: Oliver Graute @ 2020-08-31 14:54 UTC (permalink / raw)
  To: u-boot

Add i.MX8QM DMSSE20 a1 board support

U-Boot 2020.10-rc3-00177-g316f823505 (Aug 31 2020 - 16:08:37 +0200)

Model: Advantech iMX8QM DMSSE20
Board: DMS-SE20A1 8GB
Build: SCFW 494c97f3, SECO-FW d7523fe8, ATF 09c5cc9
Boot:  USB
DRAM:  8 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... Card did not respond to voltage select!
*** Warning - No block device, using default environment

In:    serial at 5a060000
Out:   serial at 5a060000
Err:   serial at 5a060000
Net:
Warning: ethernet at 5b040000 (eth0) using random MAC address - 0e:db:c9:1a:a4:a7
eth0: ethernet at 5b040000 [PRIME]
Warning: ethernet at 5b050000 (eth1) using random MAC address - d2:38:f7:68:ce:91
, eth1: ethernet at 5b050000
Hit any key to stop autoboot:  0

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
 arch/arm/dts/Makefile                         |   1 +
 arch/arm/dts/imx8qm-dmsse20-a1.dts            | 345 ++++++++++++++++++
 arch/arm/mach-imx/imx8/Kconfig                |   7 +
 board/advantech/imx8qm_dmsse20_a1/Kconfig     |  14 +
 board/advantech/imx8qm_dmsse20_a1/MAINTAINERS |   6 +
 board/advantech/imx8qm_dmsse20_a1/Makefile    |   8 +
 board/advantech/imx8qm_dmsse20_a1/README      |  61 ++++
 .../imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c     | 188 ++++++++++
 .../advantech/imx8qm_dmsse20_a1/imximage.cfg  |  21 ++
 board/advantech/imx8qm_dmsse20_a1/spl.c       | 217 +++++++++++
 common/Kconfig                                |   2 +-
 configs/imx8qm_dmsse20a1_defconfig            |  86 +++++
 include/configs/imx8qm_dmsse20.h              | 219 +++++++++++
 13 files changed, 1174 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/imx8qm-dmsse20-a1.dts
 create mode 100644 board/advantech/imx8qm_dmsse20_a1/Kconfig
 create mode 100644 board/advantech/imx8qm_dmsse20_a1/MAINTAINERS
 create mode 100644 board/advantech/imx8qm_dmsse20_a1/Makefile
 create mode 100644 board/advantech/imx8qm_dmsse20_a1/README
 create mode 100644 board/advantech/imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c
 create mode 100644 board/advantech/imx8qm_dmsse20_a1/imximage.cfg
 create mode 100644 board/advantech/imx8qm_dmsse20_a1/spl.c
 create mode 100644 configs/imx8qm_dmsse20a1_defconfig
 create mode 100644 include/configs/imx8qm_dmsse20.h

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index f8f529435b..986d1969da 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -752,6 +752,7 @@ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \
 dtb-$(CONFIG_ARCH_IMX8) += \
 	fsl-imx8qm-apalis.dtb \
 	fsl-imx8qm-mek.dtb \
+	imx8qm-dmsse20-a1.dtb \
 	imx8qm-rom7720-a1.dtb \
 	fsl-imx8qxp-ai_ml.dtb \
 	fsl-imx8qxp-colibri.dtb \
diff --git a/arch/arm/dts/imx8qm-dmsse20-a1.dts b/arch/arm/dts/imx8qm-dmsse20-a1.dts
new file mode 100644
index 0000000000..6f4f795e99
--- /dev/null
+++ b/arch/arm/dts/imx8qm-dmsse20-a1.dts
@@ -0,0 +1,345 @@
+// SPDX-License-Identifier:	GPL-2.0+
+/*
+ * Copyright 2017 NXP
+ */
+
+/dts-v1/;
+
+/* First 128KB is for PSCI ATF. */
+/memreserve/ 0x80000000 0x00020000;
+
+#include "fsl-imx8qm.dtsi"
+
+/ {
+	model = "Advantech iMX8QM DMSSE20";
+	compatible = "fsl,imx8qm-mek", "fsl,imx8qm";
+
+	aliases {
+	   mmc0 = &usdhc1;
+	   mmc2 = &usdhc3;
+	};
+
+	chosen {
+		bootargs = "console=ttyLP0,115200 earlycon=lpuart32,0x5a060000,115200";
+		stdout-path = &lpuart0;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_usb_otg1_vbus: regulator at 0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "usb_otg1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usdhc2_vmmc: usdhc2_vmmc {
+			compatible = "regulator-fixed";
+			regulator-name = "sw-3p3-sd1";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		busfreq {
+			status = "disabled";
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_1>;
+
+	imx8qm-mek {
+		pinctrl_hog_1: hoggrp-1 {
+			fsl,pins = <
+				SC_P_USB_SS3_TC0_LSIO_GPIO4_IO03	0x06000048
+			>;
+		};
+
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD	0x000014a0
+				SC_P_ENET0_MDC_CONN_ENET0_MDC			0x06000020
+				SC_P_ENET0_MDIO_CONN_ENET0_MDIO			0x06000020
+				SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x00000060
+				SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC	0x00000060
+				SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0	0x00000060
+				SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1	0x00000060
+				SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2	0x00000060
+				SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3	0x00000060
+				SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC	0x00000060
+				SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x00000060
+				SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0	0x00000060
+				SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1	0x00000060
+				SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2	0x00000060
+				SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3	0x00000060
+			>;
+		};
+
+		pinctrl_fec2: fec2grp {
+			fsl,pins = <
+				SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD	0x000014a0
+				SC_P_ENET1_MDC_CONN_ENET1_MDC			0x06000020
+				SC_P_ENET1_MDIO_CONN_ENET1_MDIO			0x06000020
+				SC_P_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL	0x00000060
+				SC_P_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC	0x00000060
+				SC_P_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0	0x00000060
+				SC_P_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1	0x00000060
+				SC_P_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2	0x00000060
+				SC_P_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3	0x00000060
+				SC_P_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC	0x00000060
+				SC_P_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL	0x00000060
+				SC_P_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0	0x00000060
+				SC_P_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1	0x00000060
+				SC_P_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2	0x00000060
+				SC_P_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3	0x00000060
+			>;
+		};
+
+		pinctrl_lpuart0: lpuart0grp {
+			fsl,pins = <
+				SC_P_UART0_RX_DMA_UART0_RX		0x06000020
+				SC_P_UART0_TX_DMA_UART0_TX		0x06000020
+			>;
+		};
+
+		pinctrl_usdhc1: usdhc1grp {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000041
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000021
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x06000041
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000040
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000020
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000020
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000020
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000020
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000020
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000020
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000020
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000020
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000020
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x06000040
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000040
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000020
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000020
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000020
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000020
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000020
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000020
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000020
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000020
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000020
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x06000040
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc2_gpio: usdhc2grpgpio {
+			fsl,pins = <
+				SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO07	0x00000020
+				SC_P_USDHC1_VSELECT_LSIO_GPIO4_IO08	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc3_gpio: usdhc3grpgpio {
+			fsl,pins = <
+				SC_P_USDHC2_WP_LSIO_GPIO4_IO11          0x00000021
+				SC_P_USDHC2_CD_B_LSIO_GPIO4_IO12        0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000041
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000021
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000021
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000021
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000021
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000021
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000040
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000020
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000020
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000020
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000020
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000020
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000040
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000020
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000020
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000020
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000020
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000020
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK         0x06000041
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD         0x00000021
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0     0x00000021
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1     0x00000021
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2     0x00000021
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3     0x00000021
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK         0x06000040
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD         0x00000020
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0     0x00000020
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1     0x00000020
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2     0x00000020
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3     0x00000020
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK         0x06000040
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD         0x00000020
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0     0x00000020
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1     0x00000020
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2     0x00000020
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3     0x00000020
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000020
+			>;
+		};
+	};
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&gpio4 {
+	status = "okay";
+};
+
+&gpio5 {
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default","state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,ar8031-phy-fixup;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy at 4 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <4>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec2>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	fsl,ar8031-phy-fixup;
+	fsl,magic-packet;
+	status = "okay";
+	fsl,mii-exclusive;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy at 4 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <4>;
+		};
+	};
+};
+
+&lpuart0 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+	status = "okay";
+};
diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig
index 9d1f73dfc7..ee6781c6f7 100644
--- a/arch/arm/mach-imx/imx8/Kconfig
+++ b/arch/arm/mach-imx/imx8/Kconfig
@@ -86,6 +86,12 @@ config TARGET_IMX8QM_ROM7720_A1
 	select SUPPORT_SPL
 	select IMX8QM
 
+config TARGET_IMX8QM_DMSSE20_A1
+	bool "Support i.MX8QM DMS-SE20-A1 board"
+	select BOARD_LATE_INIT
+	select SUPPORT_SPL
+	select IMX8QM
+
 config TARGET_IMX8QXP_MEK
 	bool "Support i.MX8QXP MEK board"
 	select BOARD_LATE_INIT
@@ -95,6 +101,7 @@ endchoice
 
 source "board/freescale/imx8qm_mek/Kconfig"
 source "board/freescale/imx8qxp_mek/Kconfig"
+source "board/advantech/imx8qm_dmsse20_a1/Kconfig"
 source "board/advantech/imx8qm_rom7720_a1/Kconfig"
 source "board/toradex/apalis-imx8/Kconfig"
 source "board/toradex/colibri-imx8x/Kconfig"
diff --git a/board/advantech/imx8qm_dmsse20_a1/Kconfig b/board/advantech/imx8qm_dmsse20_a1/Kconfig
new file mode 100644
index 0000000000..1d5e68a96f
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/Kconfig
@@ -0,0 +1,14 @@
+if TARGET_IMX8QM_DMSSE20_A1
+
+config SYS_BOARD
+	default "imx8qm_dmsse20_a1"
+
+config SYS_VENDOR
+	default "advantech"
+
+config SYS_CONFIG_NAME
+	default "imx8qm_dmsse20"
+
+source "board/freescale/common/Kconfig"
+
+endif
diff --git a/board/advantech/imx8qm_dmsse20_a1/MAINTAINERS b/board/advantech/imx8qm_dmsse20_a1/MAINTAINERS
new file mode 100644
index 0000000000..c1e8048bbb
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/MAINTAINERS
@@ -0,0 +1,6 @@
+i.MX8QM ROM DMSSE20 a1 BOARD
+M:	Oliver Graute <oliver.graute@kococonnector.com>
+S:	Maintained
+F: 	board/advantech/imx8qm_dmsse20_a1/
+F:	include/configs/imx8qm_dmsse20.h
+F: 	configs/imx8qm_dmsse20a1_defconfig
diff --git a/board/advantech/imx8qm_dmsse20_a1/Makefile b/board/advantech/imx8qm_dmsse20_a1/Makefile
new file mode 100644
index 0000000000..262ffcd683
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += imx8qm_dmsse20_a1.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/advantech/imx8qm_dmsse20_a1/README b/board/advantech/imx8qm_dmsse20_a1/README
new file mode 100644
index 0000000000..2105e9c425
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/README
@@ -0,0 +1,61 @@
+U-Boot for the NXP i.MX8QM DMSSE20-a1 board
+
+Quick Start
+===========
+
+- Build the ARM Trusted firmware binary
+- Get scfw_tcm.bin and ahab-container.img
+- Get imx-mkimage
+- Build U-Boot
+- Build imx-mkimage
+- Flash the binary into the SD card
+- Boot
+
+Get and Build the ARM Trusted firmware
+======================================
+
+$ git clone https://source.codeaurora.org/external/imx/imx-atf
+$ cd imx-atf/
+$ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga
+$ make PLAT=imx8qm bl31
+
+Get scfw_tcm.bin and ahab-container.img
+==============================
+
+$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin
+$ chmod +x imx-sc-firmware-1.1.bin
+$ ./imx-sc-firmware-1.1.bin
+$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
+$ chmod +x firmware-imx-8.0.bin
+$ ./firmware-imx-8.0.bin
+
+Or use this to avoid running random scripts from the internet,
+but note that you must agree to the license the script displays:
+
+$ dd if=imx-sc-firmware-1.1.bin of=imx-sc-firmware-1.1.tar.bz2 bs=37185 skip=1
+$ tar -xf imx-sc-firmware-1.1.tar.bz2
+$ cp imx-sc-firmware-1.1/mx8qm-val-scfw-tcm.bin $(builddir)
+
+$ dd if=firmware-imx-8.0.bin of=firmware-imx-8.0.tar.bz2 bs=37180 skip=1
+$ tar -xf firmware-imx-8.0.tar.bz2
+$ cp firmware-imx-8.0/firmware/seco/mx8qm-ahab-container.img $(builddir)
+
+Build U-Boot
+============
+
+$ export ATF_LOAD_ADDR=0x80000000
+$ export BL33_LOAD_ADDR=0x80020000
+$ make imx8qm_dmsse20a1_defconfig
+$ make u-boot.bin
+$ make flash.bin
+
+Flash the binary into the SD card
+=================================
+
+Burn the flash.bin binary to SD card offset 32KB:
+
+$ sudo dd if=flash.bin of=/dev/sd[x] bs=1k seek=32 conv=fsync
+
+Boot
+====
+Set Boot switch SW1: 011100.
diff --git a/board/advantech/imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c b/board/advantech/imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c
new file mode 100644
index 0000000000..b93d2046f5
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier:	GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ * Copyright (C) 2020 Oliver Graute <oliver.graute@kococonnector.com>
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <linux/libfdt.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/sys_proto.h>
+/* #include <power-domain.h> */
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+static iomux_cfg_t uart0_pads[] = {
+	SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads));
+}
+
+int board_early_init_f(void)
+{
+	sc_pm_clock_rate_t rate = SC_80MHZ;
+	int ret;
+
+	/* Set UART0 clock root to 80 MHz */
+	ret = sc_pm_setup_uart(SC_R_UART_0, rate);
+	if (ret)
+		return ret;
+
+	setup_iomux_uart();
+
+	/* This is needed to because Kernel do not Power Up DC_0 */
+	sc_pm_set_resource_power_mode(-1, SC_R_DC_0, SC_PM_PW_MODE_ON);
+	sc_pm_set_resource_power_mode(-1, SC_R_GPIO_5, SC_PM_PW_MODE_ON);
+
+	return 0;
+}
+
+#if IS_ENABLED(CONFIG_FEC_MXC)
+#include <miiphy.h>
+
+int board_phy_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MXC_GPIO
+
+#define LVDS_ENABLE IMX_GPIO_NR(1, 6)
+#define MIPI_ENABLE IMX_GPIO_NR(1, 7)
+
+#define BB_GPIO_3V3_1 IMX_GPIO_NR(4, 20)
+#define BB_GPIO_3V3_2 IMX_GPIO_NR(4, 24)
+#define BB_GPIO_3V3_3 IMX_GPIO_NR(4, 23)
+
+static void board_gpio_init(void)
+{
+	/* Enable BB 3V3 */
+	gpio_request(BB_GPIO_3V3_1, "bb_3v3_1");
+	gpio_direction_output(BB_GPIO_3V3_1, 1);
+	gpio_request(BB_GPIO_3V3_2, "bb_3v3_2");
+	gpio_direction_output(BB_GPIO_3V3_2, 1);
+	gpio_request(BB_GPIO_3V3_3, "bb_3v3_3");
+	gpio_direction_output(BB_GPIO_3V3_3, 1);
+
+	/* enable LVDS SAS boards */
+	gpio_request(LVDS_ENABLE, "lvds_enable");
+	gpio_direction_output(LVDS_ENABLE, 1);
+
+	/* enable MIPI SAS boards */
+	gpio_request(MIPI_ENABLE, "mipi_enable");
+	gpio_direction_output(MIPI_ENABLE, 1);
+}
+#endif
+
+int checkboard(void)
+{
+	puts("Board: DMS-SE20A1 8GB\n");
+	build_info();
+	print_bootinfo();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	if (IS_ENABLED(CONFIG_XEN))
+		return 0;
+
+#ifdef CONFIG_MXC_GPIO
+	board_gpio_init();
+#endif
+
+	return 0;
+}
+
+void board_quiesce_devices(void)
+{
+	if (IS_ENABLED(CONFIG_XEN)) {
+		/* Clear magic number to let xen know uboot is over */
+		writel(0x0, (void __iomem *)0x80000000);
+		return;
+	}
+}
+
+void detail_board_ddr_info(void)
+{
+	puts("\nDDR    ");
+}
+
+/*
+ * Board specific reset that is system reset.
+ */
+void reset_cpu(ulong addr)
+{
+	puts("SCI reboot request");
+
+	while (1)
+		putc('.');
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+	return 0;
+}
+#endif
+
+int board_mmc_get_env_dev(int devno)
+{
+	/* Use EMMC */
+	if (IS_ENABLED(CONFIG_XEN))
+		return 0;
+
+	return devno;
+}
+
+int mmc_map_to_kernel_blk(int dev_no)
+{
+	/* Use EMMC */
+	if (IS_ENABLED(CONFIG_XEN))
+		return 0;
+
+	return dev_no;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	env_set("board_name", "DMS-SE20A1");
+	env_set("board_rev", "iMX8QM");
+#endif
+
+	env_set("sec_boot", "no");
+#ifdef CONFIG_AHAB_BOOT
+	env_set("sec_boot", "yes");
+#endif
+
+	return 0;
+}
diff --git a/board/advantech/imx8qm_dmsse20_a1/imximage.cfg b/board/advantech/imx8qm_dmsse20_a1/imximage.cfg
new file mode 100644
index 0000000000..e324c7ca37
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/imximage.cfg
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier:	GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#define __ASSEMBLY__
+
+/* Boot from SD, sector size 0x400 */
+BOOT_FROM SD 0x400
+/* SoC type IMX8QM */
+SOC_TYPE IMX8QM
+/* Append seco container image */
+APPEND mx8qm-ahab-container.img
+/* Create the 2nd container */
+CONTAINER
+/* Add scfw image with exec attribute */
+IMAGE SCU mx8qm-val-scfw-tcm.bin
+/* Add ATF image with exec attribute */
+IMAGE A35 bl31.bin 0x80000000
+/* Add U-Boot image with load attribute */
+DATA A35 u-boot-dtb.bin 0x80020000
diff --git a/board/advantech/imx8qm_dmsse20_a1/spl.c b/board/advantech/imx8qm_dmsse20_a1/spl.c
new file mode 100644
index 0000000000..8eb3d53c91
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/spl.c
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier:	GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ */
+#include <common.h>
+#include <dm.h>
+#include <spl.h>
+#include <fsl_esdhc.h>
+
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <asm/arch/iomux.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ESDHC_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ESDHC_CLK_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_INPUT_PAD_CTRL	((SC_PAD_CONFIG_OD_IN << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_NORMAL_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define FSPI_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define GPIO_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define I2C_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_DV_LOW << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define UART_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+#ifdef CONFIG_FSL_ESDHC_IMX
+
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(5, 22)
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(4, 12)
+
+static struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = {
+	{USDHC1_BASE_ADDR, 0, 8},
+	{USDHC3_BASE_ADDR, 0, 4},
+};
+
+static iomux_cfg_t emmc0[] = {
+	SC_P_EMMC0_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+	SC_P_EMMC0_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA4 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA5 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA6 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA7 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_STROBE | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+static iomux_cfg_t usdhc2_sd[] = {
+	SC_P_USDHC2_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+	SC_P_USDHC2_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_WP   | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_CD_B | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+int board_mmc_init(struct bd_info *bis)
+{
+	int i, ret;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    USDHC1
+	 * mmc1                    USDHC2
+	 * mmc2                    USDHC3
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			ret = sc_pm_set_resource_power_mode(-1, SC_R_SDHC_0, SC_PM_PW_MODE_ON);
+			if (ret != SC_ERR_NONE)
+				return ret;
+
+			imx8_iomux_setup_multiple_pads(emmc0, ARRAY_SIZE(emmc0));
+			init_clk_usdhc(0);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		case 1:
+			ret = sc_pm_set_resource_power_mode(-1, SC_R_SDHC_2, SC_PM_PW_MODE_ON);
+			if (ret != SC_ERR_NONE)
+				return ret;
+			ret = sc_pm_set_resource_power_mode(-1, SC_R_GPIO_4, SC_PM_PW_MODE_ON);
+			if (ret != SC_ERR_NONE)
+				return ret;
+
+			imx8_iomux_setup_multiple_pads(usdhc2_sd, ARRAY_SIZE(usdhc2_sd));
+			init_clk_usdhc(2);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			gpio_request(USDHC2_CD_GPIO, "sd2_cd");
+			gpio_direction_input(USDHC2_CD_GPIO);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return 0;
+		}
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = 1;
+		break;
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+
+#endif /* CONFIG_FSL_ESDHC_IMX */
+
+void spl_board_init(void)
+{
+#if defined(CONFIG_SPL_SPI_SUPPORT)
+	if (sc_rm_is_resource_owned(-1, SC_R_FSPI_0)) {
+		if (sc_pm_set_resource_power_mode(-1, SC_R_FSPI_0, SC_PM_PW_MODE_ON))
+			puts("Warning: failed to initialize FSPI0\n");
+	}
+#endif
+
+	puts("Normal Boot\n");
+}
+
+void spl_board_prepare_for_boot(void)
+{
+#if defined(CONFIG_SPL_SPI_SUPPORT)
+	if (sc_rm_is_resource_owned(-1, SC_R_FSPI_0)) {
+		if (sc_pm_set_resource_power_mode(-1, SC_R_FSPI_0, SC_PM_PW_MODE_OFF))
+			puts("Warning: failed to turn off FSPI0\n");
+	}
+#endif
+}
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+	/* Just empty function now - can't decide what to choose */
+	debug("%s: %s\n", __func__, name);
+
+	return 0;
+}
+#endif
+
+void board_init_f(ulong dummy)
+{
+	/* Clear global data */
+	memset((void *)gd, 0, sizeof(gd_t));
+
+	arch_cpu_init();
+
+	board_early_init_f();
+
+	timer_init();
+
+	preloader_console_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	board_init_r(NULL, 0);
+}
diff --git a/common/Kconfig b/common/Kconfig
index c58f08ba91..538dda1c10 100644
--- a/common/Kconfig
+++ b/common/Kconfig
@@ -896,7 +896,7 @@ config BOARD_LATE_INIT
 
 config DISPLAY_CPUINFO
 	bool "Display information about the CPU during start up"
-	default y if ARC|| ARM || NIOS2 || X86 || XTENSA || M68K
+	default y if ARC || ARM || NIOS2 || X86 || XTENSA || M68K
 	help
 	  Display information about the CPU that U-Boot is running on
 	  when U-Boot starts up. The function print_cpuinfo() is called
diff --git a/configs/imx8qm_dmsse20a1_defconfig b/configs/imx8qm_dmsse20a1_defconfig
new file mode 100644
index 0000000000..242b817733
--- /dev/null
+++ b/configs/imx8qm_dmsse20a1_defconfig
@@ -0,0 +1,86 @@
+CONFIG_ARM=y
+CONFIG_SPL_SYS_ICACHE_OFF=y
+CONFIG_SPL_SYS_DCACHE_OFF=y
+CONFIG_ARCH_IMX8=y
+CONFIG_SYS_TEXT_BASE=0x80020000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_TARGET_IMX8QM_DMSSE20_A1=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_ENV_OFFSET=0x400000
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/advantech/imx8qm_dmsse20_a1/imximage.cfg"
+CONFIG_OF_CONTROL=y
+CONFIG_CI_UDC=y
+CONFIG_DM_PCA953X=y
+CONFIG_BOOTDELAY=3
+CONFIG_LOG=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_IMX_BOOTAUX=y
+CONFIG_FS_FAT=y
+CONFIG_FS_EXT4=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_IO_VOLTAGE=y
+CONFIG_MMC_UHS_SUPPORT=y
+CONFIG_MMC_HS400_SUPPORT=y
+CONFIG_MMC_BROKEN_CD=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_EXT4=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx8qm-dmsse20-a1"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_IMX8=y
+CONFIG_CPU=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_FSL_ESDHC_IMX=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+# CONFIG_EFI_LOADER is not set
+CONFIG_FEC_MXC_SHARE_MDIO=y
+CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_IMX8=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_SPL_DM_REGULATOR_GPIO=y
+CONFIG_DM_SERIAL=y
+CONFIG_FSL_LPUART=y
+CONFIG_MISC=y
+CONFIG_SMC_FUSE=y
+CONFIG_BOOTAUX_RESERVED_MEM_BASE=0x88000000
+CONFIG_BOOTAUX_RESERVED_MEM_SIZE=0x08000000
+# CONFIG_DISPLAY_CPUINFO is not set
diff --git a/include/configs/imx8qm_dmsse20.h b/include/configs/imx8qm_dmsse20.h
new file mode 100644
index 0000000000..e1e0bc6e38
--- /dev/null
+++ b/include/configs/imx8qm_dmsse20.h
@@ -0,0 +1,219 @@
+// SPDX-License-Identifier:	GPL-2.0+
+/*
+ * Copyright 2017-2019 NXP
+ */
+
+#ifndef __IMX8QM_DMSSE20_H
+#define __IMX8QM_DMSSE20_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+#define CONFIG_REMAKE_ELF
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_MAX_SIZE		(124 * 1024)
+#define CONFIG_SPL_BSS_START_ADDR	0x00128000
+#define CONFIG_SPL_BSS_MAX_SIZE	0x1000  /* 4 KB */
+#endif
+
+#define CONFIG_NR_DRAM_BANKS		4
+
+/* #define CONFIG_ARCH_MISC_INIT */
+
+/* #define CONFIG_CMD_READ */
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_BOARD_SETUP
+
+/* #undef CONFIG_CMD_EXPORTENV */
+/* #undef CONFIG_CMD_IMPORTENV */
+/* #undef CONFIG_CMD_IMLS */
+
+/* #undef CONFIG_CMD_CRC32 */
+#undef CONFIG_BOOTM_NETBSD
+
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define USDHC1_BASE_ADDR		0x5B010000
+#define USDHC2_BASE_ADDR		0x5B020000
+#define USDHC3_BASE_ADDR		0x5B030000
+
+#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+/* FUSE command */
+#define CONFIG_CMD_FUSE
+
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define FEC_QUIRK_ENET_MAC
+
+#define CONFIG_PHY_GIGE /* Support for 1000BASE-X */
+
+/* ENET0 connects AR8031 on CPU board */
+#define CONFIG_FEC1_ENET_DEV 0
+
+/* ENET1 connects AR8031 on CPU board */
+#define CONFIG_FEC2_ENET_DEV 1
+#define CONFIG_FEC_MXC_PHYADDR		0x4
+#define IMX_FEC_BASE			0x5B040000
+/* FEC1 */
+#define IMX_FEC1_BASE			0x5B040000
+#define CONFIG_FEC1_MXC_PHYADDR		0x4
+#define CONFIG_ETHPRIME			"eth0"
+/* FEC2 */
+#define IMX_FEC2_BASE			0x5B050000
+#define CONFIG_FEC2_MXC_PHYADDR		0x4
+#define CONFIG_ETHPRIME1		"eth1"
+
+/* Boot M4 */
+#define M4_BOOT_ENV \
+	"m4_0_image=m4_0.bin\0" \
+	"m4_1_image=m4_1.bin\0" \
+	"loadm4image_0=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_0_image}\0" \
+	"loadm4image_1=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_1_image}\0" \
+	"m4boot_0=run loadm4image_0; dcache flush; bootaux ${loadaddr} 0\0" \
+	"m4boot_1=run loadm4image_1; dcache flush; bootaux ${loadaddr} 1\0" \
+
+#ifdef CONFIG_NAND_BOOT
+#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:128m(boot),32m(kernel),16m(dtb),8m(misc),-(rootfs) "
+#else
+#define MFG_NAND_PARTITION ""
+#endif
+
+#define CONFIG_MFG_ENV_SETTINGS \
+	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
+	"initrd_addr=0x83100000\0" \
+	"initrd_high=0xffffffffffffffff\0" \
+	"emmc_dev=0\0" \
+	"sd_dev=1\0" \
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	CONFIG_MFG_ENV_SETTINGS \
+	M4_BOOT_ENV \
+	"script=boot.scr\0" \
+	"image=Image\0" \
+	"panel=NULL\0" \
+	"console=ttyLP0\0" \
+	"earlycon=lpuart32,0x5a060000\0" \
+	"fdt_addr=0x83000000\0"			\
+	"fdt_high=0xffffffffffffffff\0"		\
+	"boot_fdt=try\0" \
+	"fdt_file=imx8qm-dmsse20-a1.dtb\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} earlycon=${earlycon},${baudrate} root=${mmcroot}\0 " \
+	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"booti ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"echo WARN: Cannot load the DT; " \
+			"fi; " \
+		"else " \
+			"echo wait for boot; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} earlycon=${earlycon},${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp mac=${ethaddr} nfsroot=${serverip}:${nfsroot},v3,tcp rw\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs;  " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${loadaddr} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"booti ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"echo WARN: Cannot load the DT; " \
+			"fi; " \
+		"else " \
+			"booti; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev}; if mmc rescan; then " \
+		   "if run loadbootscript; then " \
+			   "run bootscript; " \
+		   "else " \
+			   "if run loadimage; then " \
+				   "run mmcboot; " \
+			   "else run netboot; " \
+			   "fi; " \
+		   "fi; " \
+	   "else booti ${loadaddr} - ${fdt_addr}; fi"
+
+/* Link Definitions */
+#define CONFIG_LOADADDR			0x80280000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_SYS_INIT_SP_ADDR		0x80200000
+
+/* Default environment is in SD */
+
+#ifdef CONFIG_QSPI_BOOT
+#define CONFIG_ENV_SECT_SIZE	(128 * 1024)
+#define CONFIG_ENV_SPI_BUS	CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS	CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE	CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ	CONFIG_SF_DEFAULT_SPEED
+#else
+#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
+#endif
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	0
+
+#define CONFIG_SYS_MMC_ENV_DEV		2   /* USDHC3 */
+#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC3 */
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (32 * 1024)) * 1024)
+
+#define CONFIG_SYS_SDRAM_BASE		0x080000000
+#define PHYS_SDRAM_1			0x080000000
+#define PHYS_SDRAM_2			0x880000000
+#define PHYS_SDRAM_1_SIZE		0x080000000	/* 2 GB */
+#define PHYS_SDRAM_2_SIZE		0x180000000	/* 6 GB */
+
+#define CONFIG_SYS_MEMTEST_START	0xA0000000
+#define CONFIG_SYS_MEMTEST_END      (CONFIG_SYS_MEMTEST_START + (PHYS_SDRAM_1_SIZE >> 2))
+
+/* Serial */
+#define CONFIG_BAUDRATE			115200
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY		8000000	/* 8MHz */
+
+#define CONFIG_IMX_SMMU
+
+/* MT35XU512ABA1G12 has only one Die, so QSPI0 B won't work */
+#ifdef CONFIG_FSL_FSPI
+#define CONFIG_SF_DEFAULT_BUS		0
+#define CONFIG_SF_DEFAULT_CS		0
+#define CONFIG_SF_DEFAULT_SPEED		40000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#define FSL_FSPI_FLASH_SIZE		SZ_64M
+#define FSL_FSPI_FLASH_NUM		1
+#define FSPI0_BASE_ADDR			0x5d120000
+#define FSPI0_AMBA_BASE			0
+#define CONFIG_SYS_FSL_FSPI_AHB
+#endif
+
+/* #define CONFIG_OF_SYSTEM_SETUP */
+
+#endif /* __IMX8QM_DMSSE20_H */
-- 
2.17.1

^ permalink raw reply related	[flat|nested] 5+ messages in thread