From: Lars Povlsen <lars.povlsen@microchip.com>
To: Linus Walleij <linus.walleij@linaro.org>
Cc: Lars Povlsen <lars.povlsen@microchip.com>,
Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>,
<devicetree@vger.kernel.org>, <linux-gpio@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Andy Shevchenko <andy.shevchenko@gmail.com>
Subject: [PATCH v10 3/3] arm64: dts: sparx5: Add SGPIO devices
Date: Fri, 13 Nov 2020 15:51:51 +0100 [thread overview]
Message-ID: <20201113145151.68900-4-lars.povlsen@microchip.com> (raw)
In-Reply-To: <20201113145151.68900-1-lars.povlsen@microchip.com>
This adds SGPIO devices for the Sparx5 SoC and configures it for the
applicable reference boards.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
---
arch/arm64/boot/dts/microchip/sparx5.dtsi | 91 ++++++
.../boot/dts/microchip/sparx5_pcb125.dts | 5 +
.../dts/microchip/sparx5_pcb134_board.dtsi | 258 ++++++++++++++++++
.../dts/microchip/sparx5_pcb135_board.dtsi | 55 ++++
4 files changed, 409 insertions(+)
diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index 3cb01c39c3c8..f09707297a9f 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -226,6 +226,22 @@ si2_pins: si2-pins {
function = "si2";
};
+ sgpio0_pins: sgpio-pins {
+ pins = "GPIO_0", "GPIO_1", "GPIO_2", "GPIO_3";
+ function = "sg0";
+ };
+
+ sgpio1_pins: sgpio1-pins {
+ pins = "GPIO_4", "GPIO_5", "GPIO_12", "GPIO_13";
+ function = "sg1";
+ };
+
+ sgpio2_pins: sgpio2-pins {
+ pins = "GPIO_30", "GPIO_31", "GPIO_32",
+ "GPIO_33";
+ function = "sg2";
+ };
+
uart_pins: uart-pins {
pins = "GPIO_10", "GPIO_11";
function = "uart";
@@ -256,6 +272,81 @@ emmc_pins: emmc-pins {
};
};
+ sgpio0: gpio@61101036c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "microchip,sparx5-sgpio";
+ status = "disabled";
+ clocks = <&sys_clk>;
+ pinctrl-0 = <&sgpio0_pins>;
+ pinctrl-names = "default";
+ reg = <0x6 0x1101036c 0x100>;
+ sgpio_in0: gpio@0 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ sgpio_out0: gpio@1 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <1>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ };
+
+ sgpio1: gpio@611010484 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "microchip,sparx5-sgpio";
+ status = "disabled";
+ clocks = <&sys_clk>;
+ pinctrl-0 = <&sgpio1_pins>;
+ pinctrl-names = "default";
+ reg = <0x6 0x11010484 0x100>;
+ sgpio_in1: gpio@0 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ sgpio_out1: gpio@1 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <1>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ };
+
+ sgpio2: gpio@61101059c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "microchip,sparx5-sgpio";
+ status = "disabled";
+ clocks = <&sys_clk>;
+ pinctrl-0 = <&sgpio2_pins>;
+ pinctrl-names = "default";
+ reg = <0x6 0x1101059c 0x100>;
+ sgpio_in2: gpio@0 {
+ reg = <0>;
+ compatible = "microchip,sparx5-sgpio-bank";
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ sgpio_out2: gpio@1 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <1>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ };
+
i2c0: i2c@600101000 {
compatible = "snps,designware-i2c";
status = "disabled";
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
index 6b2da7c7520c..9baa085d7861 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
@@ -69,6 +69,11 @@ spi-flash@9 {
};
};
+&sgpio0 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <0 23>;
+};
+
&i2c1 {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index f37b478d6534..6820579448d0 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -36,6 +36,242 @@ gpio-restart {
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
priority = <200>;
};
+
+ leds {
+ compatible = "gpio-leds";
+ led@0 {
+ label = "twr0:green";
+ gpios = <&sgpio_out0 8 0 GPIO_ACTIVE_LOW>;
+ };
+ led@1 {
+ label = "twr0:yellow";
+ gpios = <&sgpio_out0 8 1 GPIO_ACTIVE_LOW>;
+ };
+ led@2 {
+ label = "twr1:green";
+ gpios = <&sgpio_out0 9 0 GPIO_ACTIVE_LOW>;
+ };
+ led@3 {
+ label = "twr1:yellow";
+ gpios = <&sgpio_out0 9 1 GPIO_ACTIVE_LOW>;
+ };
+ led@4 {
+ label = "twr2:green";
+ gpios = <&sgpio_out0 10 0 GPIO_ACTIVE_LOW>;
+ };
+ led@5 {
+ label = "twr2:yellow";
+ gpios = <&sgpio_out0 10 1 GPIO_ACTIVE_LOW>;
+ };
+ led@6 {
+ label = "twr3:green";
+ gpios = <&sgpio_out0 11 0 GPIO_ACTIVE_LOW>;
+ };
+ led@7 {
+ label = "twr3:yellow";
+ gpios = <&sgpio_out0 11 1 GPIO_ACTIVE_LOW>;
+ };
+ led@8 {
+ label = "eth12:green";
+ gpios = <&sgpio_out0 12 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@9 {
+ label = "eth12:yellow";
+ gpios = <&sgpio_out0 12 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@10 {
+ label = "eth13:green";
+ gpios = <&sgpio_out0 13 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@11 {
+ label = "eth13:yellow";
+ gpios = <&sgpio_out0 13 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@12 {
+ label = "eth14:green";
+ gpios = <&sgpio_out0 14 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@13 {
+ label = "eth14:yellow";
+ gpios = <&sgpio_out0 14 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@14 {
+ label = "eth15:green";
+ gpios = <&sgpio_out0 15 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@15 {
+ label = "eth15:yellow";
+ gpios = <&sgpio_out0 15 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@16 {
+ label = "eth48:green";
+ gpios = <&sgpio_out1 16 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@17 {
+ label = "eth48:yellow";
+ gpios = <&sgpio_out1 16 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@18 {
+ label = "eth49:green";
+ gpios = <&sgpio_out1 17 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@19 {
+ label = "eth49:yellow";
+ gpios = <&sgpio_out1 17 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@20 {
+ label = "eth50:green";
+ gpios = <&sgpio_out1 18 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@21 {
+ label = "eth50:yellow";
+ gpios = <&sgpio_out1 18 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@22 {
+ label = "eth51:green";
+ gpios = <&sgpio_out1 19 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@23 {
+ label = "eth51:yellow";
+ gpios = <&sgpio_out1 19 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@24 {
+ label = "eth52:green";
+ gpios = <&sgpio_out1 20 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@25 {
+ label = "eth52:yellow";
+ gpios = <&sgpio_out1 20 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@26 {
+ label = "eth53:green";
+ gpios = <&sgpio_out1 21 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@27 {
+ label = "eth53:yellow";
+ gpios = <&sgpio_out1 21 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@28 {
+ label = "eth54:green";
+ gpios = <&sgpio_out1 22 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@29 {
+ label = "eth54:yellow";
+ gpios = <&sgpio_out1 22 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@30 {
+ label = "eth55:green";
+ gpios = <&sgpio_out1 23 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@31 {
+ label = "eth55:yellow";
+ gpios = <&sgpio_out1 23 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@32 {
+ label = "eth56:green";
+ gpios = <&sgpio_out1 24 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@33 {
+ label = "eth56:yellow";
+ gpios = <&sgpio_out1 24 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@34 {
+ label = "eth57:green";
+ gpios = <&sgpio_out1 25 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@35 {
+ label = "eth57:yellow";
+ gpios = <&sgpio_out1 25 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@36 {
+ label = "eth58:green";
+ gpios = <&sgpio_out1 26 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@37 {
+ label = "eth58:yellow";
+ gpios = <&sgpio_out1 26 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@38 {
+ label = "eth59:green";
+ gpios = <&sgpio_out1 27 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@39 {
+ label = "eth59:yellow";
+ gpios = <&sgpio_out1 27 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@40 {
+ label = "eth60:green";
+ gpios = <&sgpio_out1 28 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@41 {
+ label = "eth60:yellow";
+ gpios = <&sgpio_out1 28 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@42 {
+ label = "eth61:green";
+ gpios = <&sgpio_out1 29 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@43 {
+ label = "eth61:yellow";
+ gpios = <&sgpio_out1 29 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@44 {
+ label = "eth62:green";
+ gpios = <&sgpio_out1 30 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@45 {
+ label = "eth62:yellow";
+ gpios = <&sgpio_out1 30 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@46 {
+ label = "eth63:green";
+ gpios = <&sgpio_out1 31 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@47 {
+ label = "eth63:yellow";
+ gpios = <&sgpio_out1 31 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
};
&spi0 {
@@ -70,6 +306,28 @@ spi-flash@9 {
};
};
+&sgpio0 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <8 15>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
+&sgpio1 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <24 31>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
&gpio {
i2cmux_pins_i: i2cmux-pins-i {
pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19",
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index b02b8c8ce44d..e28c6dd16377 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -20,6 +20,50 @@ gpio-restart {
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
priority = <200>;
};
+
+ leds {
+ compatible = "gpio-leds";
+ led@0 {
+ label = "eth60:yellow";
+ gpios = <&sgpio_out1 28 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@1 {
+ label = "eth60:green";
+ gpios = <&sgpio_out1 28 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@2 {
+ label = "eth61:yellow";
+ gpios = <&sgpio_out1 29 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@3 {
+ label = "eth61:green";
+ gpios = <&sgpio_out1 29 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@4 {
+ label = "eth62:yellow";
+ gpios = <&sgpio_out1 30 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@5 {
+ label = "eth62:green";
+ gpios = <&sgpio_out1 30 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@6 {
+ label = "eth63:yellow";
+ gpios = <&sgpio_out1 31 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@7 {
+ label = "eth63:green";
+ gpios = <&sgpio_out1 31 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
};
&gpio {
@@ -83,6 +127,17 @@ spi-flash@9 {
};
};
+&sgpio1 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <24 31>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
&axi {
i2c0_imux: i2c0-imux@0 {
compatible = "i2c-mux-pinctrl";
--
2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Lars Povlsen <lars.povlsen@microchip.com>
To: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree@vger.kernel.org,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
linux-kernel@vger.kernel.org,
Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>,
linux-gpio@vger.kernel.org,
Andy Shevchenko <andy.shevchenko@gmail.com>,
Lars Povlsen <lars.povlsen@microchip.com>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH v10 3/3] arm64: dts: sparx5: Add SGPIO devices
Date: Fri, 13 Nov 2020 15:51:51 +0100 [thread overview]
Message-ID: <20201113145151.68900-4-lars.povlsen@microchip.com> (raw)
In-Reply-To: <20201113145151.68900-1-lars.povlsen@microchip.com>
This adds SGPIO devices for the Sparx5 SoC and configures it for the
applicable reference boards.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
---
arch/arm64/boot/dts/microchip/sparx5.dtsi | 91 ++++++
.../boot/dts/microchip/sparx5_pcb125.dts | 5 +
.../dts/microchip/sparx5_pcb134_board.dtsi | 258 ++++++++++++++++++
.../dts/microchip/sparx5_pcb135_board.dtsi | 55 ++++
4 files changed, 409 insertions(+)
diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index 3cb01c39c3c8..f09707297a9f 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -226,6 +226,22 @@ si2_pins: si2-pins {
function = "si2";
};
+ sgpio0_pins: sgpio-pins {
+ pins = "GPIO_0", "GPIO_1", "GPIO_2", "GPIO_3";
+ function = "sg0";
+ };
+
+ sgpio1_pins: sgpio1-pins {
+ pins = "GPIO_4", "GPIO_5", "GPIO_12", "GPIO_13";
+ function = "sg1";
+ };
+
+ sgpio2_pins: sgpio2-pins {
+ pins = "GPIO_30", "GPIO_31", "GPIO_32",
+ "GPIO_33";
+ function = "sg2";
+ };
+
uart_pins: uart-pins {
pins = "GPIO_10", "GPIO_11";
function = "uart";
@@ -256,6 +272,81 @@ emmc_pins: emmc-pins {
};
};
+ sgpio0: gpio@61101036c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "microchip,sparx5-sgpio";
+ status = "disabled";
+ clocks = <&sys_clk>;
+ pinctrl-0 = <&sgpio0_pins>;
+ pinctrl-names = "default";
+ reg = <0x6 0x1101036c 0x100>;
+ sgpio_in0: gpio@0 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ sgpio_out0: gpio@1 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <1>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ };
+
+ sgpio1: gpio@611010484 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "microchip,sparx5-sgpio";
+ status = "disabled";
+ clocks = <&sys_clk>;
+ pinctrl-0 = <&sgpio1_pins>;
+ pinctrl-names = "default";
+ reg = <0x6 0x11010484 0x100>;
+ sgpio_in1: gpio@0 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ sgpio_out1: gpio@1 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <1>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ };
+
+ sgpio2: gpio@61101059c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "microchip,sparx5-sgpio";
+ status = "disabled";
+ clocks = <&sys_clk>;
+ pinctrl-0 = <&sgpio2_pins>;
+ pinctrl-names = "default";
+ reg = <0x6 0x1101059c 0x100>;
+ sgpio_in2: gpio@0 {
+ reg = <0>;
+ compatible = "microchip,sparx5-sgpio-bank";
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ sgpio_out2: gpio@1 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <1>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ ngpios = <96>;
+ };
+ };
+
i2c0: i2c@600101000 {
compatible = "snps,designware-i2c";
status = "disabled";
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
index 6b2da7c7520c..9baa085d7861 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
@@ -69,6 +69,11 @@ spi-flash@9 {
};
};
+&sgpio0 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <0 23>;
+};
+
&i2c1 {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index f37b478d6534..6820579448d0 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -36,6 +36,242 @@ gpio-restart {
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
priority = <200>;
};
+
+ leds {
+ compatible = "gpio-leds";
+ led@0 {
+ label = "twr0:green";
+ gpios = <&sgpio_out0 8 0 GPIO_ACTIVE_LOW>;
+ };
+ led@1 {
+ label = "twr0:yellow";
+ gpios = <&sgpio_out0 8 1 GPIO_ACTIVE_LOW>;
+ };
+ led@2 {
+ label = "twr1:green";
+ gpios = <&sgpio_out0 9 0 GPIO_ACTIVE_LOW>;
+ };
+ led@3 {
+ label = "twr1:yellow";
+ gpios = <&sgpio_out0 9 1 GPIO_ACTIVE_LOW>;
+ };
+ led@4 {
+ label = "twr2:green";
+ gpios = <&sgpio_out0 10 0 GPIO_ACTIVE_LOW>;
+ };
+ led@5 {
+ label = "twr2:yellow";
+ gpios = <&sgpio_out0 10 1 GPIO_ACTIVE_LOW>;
+ };
+ led@6 {
+ label = "twr3:green";
+ gpios = <&sgpio_out0 11 0 GPIO_ACTIVE_LOW>;
+ };
+ led@7 {
+ label = "twr3:yellow";
+ gpios = <&sgpio_out0 11 1 GPIO_ACTIVE_LOW>;
+ };
+ led@8 {
+ label = "eth12:green";
+ gpios = <&sgpio_out0 12 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@9 {
+ label = "eth12:yellow";
+ gpios = <&sgpio_out0 12 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@10 {
+ label = "eth13:green";
+ gpios = <&sgpio_out0 13 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@11 {
+ label = "eth13:yellow";
+ gpios = <&sgpio_out0 13 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@12 {
+ label = "eth14:green";
+ gpios = <&sgpio_out0 14 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@13 {
+ label = "eth14:yellow";
+ gpios = <&sgpio_out0 14 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@14 {
+ label = "eth15:green";
+ gpios = <&sgpio_out0 15 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@15 {
+ label = "eth15:yellow";
+ gpios = <&sgpio_out0 15 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@16 {
+ label = "eth48:green";
+ gpios = <&sgpio_out1 16 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@17 {
+ label = "eth48:yellow";
+ gpios = <&sgpio_out1 16 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@18 {
+ label = "eth49:green";
+ gpios = <&sgpio_out1 17 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@19 {
+ label = "eth49:yellow";
+ gpios = <&sgpio_out1 17 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@20 {
+ label = "eth50:green";
+ gpios = <&sgpio_out1 18 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@21 {
+ label = "eth50:yellow";
+ gpios = <&sgpio_out1 18 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@22 {
+ label = "eth51:green";
+ gpios = <&sgpio_out1 19 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@23 {
+ label = "eth51:yellow";
+ gpios = <&sgpio_out1 19 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@24 {
+ label = "eth52:green";
+ gpios = <&sgpio_out1 20 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@25 {
+ label = "eth52:yellow";
+ gpios = <&sgpio_out1 20 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@26 {
+ label = "eth53:green";
+ gpios = <&sgpio_out1 21 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@27 {
+ label = "eth53:yellow";
+ gpios = <&sgpio_out1 21 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@28 {
+ label = "eth54:green";
+ gpios = <&sgpio_out1 22 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@29 {
+ label = "eth54:yellow";
+ gpios = <&sgpio_out1 22 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@30 {
+ label = "eth55:green";
+ gpios = <&sgpio_out1 23 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@31 {
+ label = "eth55:yellow";
+ gpios = <&sgpio_out1 23 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@32 {
+ label = "eth56:green";
+ gpios = <&sgpio_out1 24 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@33 {
+ label = "eth56:yellow";
+ gpios = <&sgpio_out1 24 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@34 {
+ label = "eth57:green";
+ gpios = <&sgpio_out1 25 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@35 {
+ label = "eth57:yellow";
+ gpios = <&sgpio_out1 25 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@36 {
+ label = "eth58:green";
+ gpios = <&sgpio_out1 26 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@37 {
+ label = "eth58:yellow";
+ gpios = <&sgpio_out1 26 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@38 {
+ label = "eth59:green";
+ gpios = <&sgpio_out1 27 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@39 {
+ label = "eth59:yellow";
+ gpios = <&sgpio_out1 27 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@40 {
+ label = "eth60:green";
+ gpios = <&sgpio_out1 28 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@41 {
+ label = "eth60:yellow";
+ gpios = <&sgpio_out1 28 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@42 {
+ label = "eth61:green";
+ gpios = <&sgpio_out1 29 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@43 {
+ label = "eth61:yellow";
+ gpios = <&sgpio_out1 29 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@44 {
+ label = "eth62:green";
+ gpios = <&sgpio_out1 30 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@45 {
+ label = "eth62:yellow";
+ gpios = <&sgpio_out1 30 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@46 {
+ label = "eth63:green";
+ gpios = <&sgpio_out1 31 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led@47 {
+ label = "eth63:yellow";
+ gpios = <&sgpio_out1 31 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
};
&spi0 {
@@ -70,6 +306,28 @@ spi-flash@9 {
};
};
+&sgpio0 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <8 15>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
+&sgpio1 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <24 31>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
&gpio {
i2cmux_pins_i: i2cmux-pins-i {
pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19",
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index b02b8c8ce44d..e28c6dd16377 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -20,6 +20,50 @@ gpio-restart {
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
priority = <200>;
};
+
+ leds {
+ compatible = "gpio-leds";
+ led@0 {
+ label = "eth60:yellow";
+ gpios = <&sgpio_out1 28 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@1 {
+ label = "eth60:green";
+ gpios = <&sgpio_out1 28 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@2 {
+ label = "eth61:yellow";
+ gpios = <&sgpio_out1 29 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@3 {
+ label = "eth61:green";
+ gpios = <&sgpio_out1 29 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@4 {
+ label = "eth62:yellow";
+ gpios = <&sgpio_out1 30 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@5 {
+ label = "eth62:green";
+ gpios = <&sgpio_out1 30 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@6 {
+ label = "eth63:yellow";
+ gpios = <&sgpio_out1 31 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led@7 {
+ label = "eth63:green";
+ gpios = <&sgpio_out1 31 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
};
&gpio {
@@ -83,6 +127,17 @@ spi-flash@9 {
};
};
+&sgpio1 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <24 31>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
&axi {
i2c0_imux: i2c0-imux@0 {
compatible = "i2c-mux-pinctrl";
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-11-13 14:52 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-13 14:51 [PATCH v10 0/3] Adding support for Microchip/Microsemi serial GPIO controller Lars Povlsen
2020-11-13 14:51 ` Lars Povlsen
2020-11-13 14:51 ` [PATCH v10 1/3] dt-bindings: pinctrl: Add bindings for pinctrl-microchip-sgpio driver Lars Povlsen
2020-11-13 14:51 ` Lars Povlsen
2020-11-13 14:51 ` [PATCH v10 2/3] pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO Lars Povlsen
2020-11-13 14:51 ` Lars Povlsen
2020-11-13 14:51 ` Lars Povlsen [this message]
2020-11-13 14:51 ` [PATCH v10 3/3] arm64: dts: sparx5: Add SGPIO devices Lars Povlsen
2020-11-23 14:31 ` Linus Walleij
2020-11-23 14:31 ` Linus Walleij
2020-11-23 15:03 ` Lars Povlsen
2020-11-23 15:03 ` Lars Povlsen
2020-12-20 22:48 ` Andrew Lunn
2020-12-20 22:48 ` Andrew Lunn
2020-12-22 10:09 ` Lars Povlsen
2020-12-22 10:09 ` Lars Povlsen
2020-12-22 13:56 ` Andrew Lunn
2020-12-22 13:56 ` Andrew Lunn
2020-12-22 14:58 ` Lars Povlsen
2020-12-22 14:58 ` Lars Povlsen
2020-11-23 14:30 ` [PATCH v10 0/3] Adding support for Microchip/Microsemi serial GPIO controller Linus Walleij
2020-11-23 14:30 ` Linus Walleij
2020-11-23 15:05 ` Lars Povlsen
2020-11-23 15:05 ` Lars Povlsen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201113145151.68900-4-lars.povlsen@microchip.com \
--to=lars.povlsen@microchip.com \
--cc=UNGLinuxDriver@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=andy.shevchenko@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.