* [PATCH 1/2] mmc: rtsx: add delay before power on
@ 2020-12-30 9:04 ricky_wu
2020-12-30 9:04 ` [PATCH 2/2] mmc: rtsx: Add MMC_CAP2_NO_SDIO flag ricky_wu
2021-01-13 9:58 ` [PATCH 1/2] mmc: rtsx: add delay before power on Ulf Hansson
0 siblings, 2 replies; 5+ messages in thread
From: ricky_wu @ 2020-12-30 9:04 UTC (permalink / raw)
To: ulf.hansson, ricky_wu, gregkh, rui_feng, rmfrfs, dianders,
lee.jones, linux-mmc, linux-kernel
From: Ricky Wu <ricky_wu@realtek.com>
Make sure voltage below 0.5V before power on
when do power cycle
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
---
drivers/mmc/host/rtsx_pci_sdmmc.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/mmc/host/rtsx_pci_sdmmc.c b/drivers/mmc/host/rtsx_pci_sdmmc.c
index e6f5bbce5685..d21b99962b36 100644
--- a/drivers/mmc/host/rtsx_pci_sdmmc.c
+++ b/drivers/mmc/host/rtsx_pci_sdmmc.c
@@ -906,6 +906,8 @@ static int sd_power_on(struct realtek_pci_sdmmc *host)
if (host->power_state == SDMMC_POWER_ON)
return 0;
+ mdelay(100);
+
rtsx_pci_init_cmd(pcr);
rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_SELECT, 0x07, SD_MOD_SEL);
rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_SHARE_MODE,
--
2.17.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/2] mmc: rtsx: Add MMC_CAP2_NO_SDIO flag
2020-12-30 9:04 [PATCH 1/2] mmc: rtsx: add delay before power on ricky_wu
@ 2020-12-30 9:04 ` ricky_wu
2021-01-13 11:25 ` Ulf Hansson
2021-01-13 9:58 ` [PATCH 1/2] mmc: rtsx: add delay before power on Ulf Hansson
1 sibling, 1 reply; 5+ messages in thread
From: ricky_wu @ 2020-12-30 9:04 UTC (permalink / raw)
To: ulf.hansson, ricky_wu, gregkh, rui_feng, rmfrfs, dianders,
lee.jones, linux-mmc, linux-kernel
From: Ricky Wu <ricky_wu@realtek.com>
Added flag MMC_CAP2_NO_SDIO to mmc->caps2
Card Reader not support SDIO
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
---
drivers/mmc/host/rtsx_pci_sdmmc.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/rtsx_pci_sdmmc.c b/drivers/mmc/host/rtsx_pci_sdmmc.c
index d21b99962b36..6a8b0282f272 100644
--- a/drivers/mmc/host/rtsx_pci_sdmmc.c
+++ b/drivers/mmc/host/rtsx_pci_sdmmc.c
@@ -1427,7 +1427,8 @@ static void realtek_init_host(struct realtek_pci_sdmmc *host)
MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25;
if (pcr->rtd3_en)
mmc->caps = mmc->caps | MMC_CAP_AGGRESSIVE_PM;
- mmc->caps2 = MMC_CAP2_NO_PRESCAN_POWERUP | MMC_CAP2_FULL_PWR_CYCLE;
+ mmc->caps2 = MMC_CAP2_NO_PRESCAN_POWERUP | MMC_CAP2_FULL_PWR_CYCLE |
+ MMC_CAP2_NO_SDIO;
mmc->max_current_330 = 400;
mmc->max_current_180 = 800;
mmc->ops = &realtek_pci_sdmmc_ops;
--
2.17.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 1/2] mmc: rtsx: add delay before power on
2020-12-30 9:04 [PATCH 1/2] mmc: rtsx: add delay before power on ricky_wu
2020-12-30 9:04 ` [PATCH 2/2] mmc: rtsx: Add MMC_CAP2_NO_SDIO flag ricky_wu
@ 2021-01-13 9:58 ` Ulf Hansson
2021-01-13 10:20 ` 吳昊澄 Ricky
1 sibling, 1 reply; 5+ messages in thread
From: Ulf Hansson @ 2021-01-13 9:58 UTC (permalink / raw)
To: 吳昊澄 Ricky
Cc: Greg Kroah-Hartman, Rui Feng, Rui Miguel Silva, Doug Anderson,
Lee Jones, linux-mmc, Linux Kernel Mailing List
On Wed, 30 Dec 2020 at 10:04, <ricky_wu@realtek.com> wrote:
>
> From: Ricky Wu <ricky_wu@realtek.com>
>
> Make sure voltage below 0.5V before power on
> when do power cycle
>
> Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
> ---
> drivers/mmc/host/rtsx_pci_sdmmc.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/drivers/mmc/host/rtsx_pci_sdmmc.c b/drivers/mmc/host/rtsx_pci_sdmmc.c
> index e6f5bbce5685..d21b99962b36 100644
> --- a/drivers/mmc/host/rtsx_pci_sdmmc.c
> +++ b/drivers/mmc/host/rtsx_pci_sdmmc.c
> @@ -906,6 +906,8 @@ static int sd_power_on(struct realtek_pci_sdmmc *host)
> if (host->power_state == SDMMC_POWER_ON)
> return 0;
>
> + mdelay(100);
> +
Why exactly 100 ms? Can you at least add a comment about why in the code?
Moreover, I think you should convert to use msleep() rather than mdelay.
> rtsx_pci_init_cmd(pcr);
> rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_SELECT, 0x07, SD_MOD_SEL);
> rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_SHARE_MODE,
> --
> 2.17.1
>
Kind regards
Uffe
^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: [PATCH 1/2] mmc: rtsx: add delay before power on
2021-01-13 9:58 ` [PATCH 1/2] mmc: rtsx: add delay before power on Ulf Hansson
@ 2021-01-13 10:20 ` 吳昊澄 Ricky
0 siblings, 0 replies; 5+ messages in thread
From: 吳昊澄 Ricky @ 2021-01-13 10:20 UTC (permalink / raw)
To: Ulf Hansson
Cc: Greg Kroah-Hartman, Rui Feng, Rui Miguel Silva, Doug Anderson,
Lee Jones, linux-mmc, Linux Kernel Mailing List
> On Wed, 30 Dec 2020 at 10:04, <ricky_wu@realtek.com> wrote:
> >
> > From: Ricky Wu <ricky_wu@realtek.com>
> >
> > Make sure voltage below 0.5V before power on when do power cycle
> >
> > Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
> > ---
> > drivers/mmc/host/rtsx_pci_sdmmc.c | 2 ++
> > 1 file changed, 2 insertions(+)
> >
> > diff --git a/drivers/mmc/host/rtsx_pci_sdmmc.c
> > b/drivers/mmc/host/rtsx_pci_sdmmc.c
> > index e6f5bbce5685..d21b99962b36 100644
> > --- a/drivers/mmc/host/rtsx_pci_sdmmc.c
> > +++ b/drivers/mmc/host/rtsx_pci_sdmmc.c
> > @@ -906,6 +906,8 @@ static int sd_power_on(struct realtek_pci_sdmmc
> *host)
> > if (host->power_state == SDMMC_POWER_ON)
> > return 0;
> >
> > + mdelay(100);
> > +
>
> Why exactly 100 ms? Can you at least add a comment about why in the code?
>
> Moreover, I think you should convert to use msleep() rather than mdelay.
>
Because we need to make sure voltage below 0.5V before power on
mmc-core will do quickly power cycle at recognition card phase,
we need at least 100ms to make our device voltage below 0.5V
I will change mdelay() to msleep()
> > rtsx_pci_init_cmd(pcr);
> > rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_SELECT, 0x07,
> SD_MOD_SEL);
> > rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_SHARE_MODE,
> > --
> > 2.17.1
> >
>
> Kind regards
> Uffe
>
> ------Please consider the environment before printing this e-mail.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 2/2] mmc: rtsx: Add MMC_CAP2_NO_SDIO flag
2020-12-30 9:04 ` [PATCH 2/2] mmc: rtsx: Add MMC_CAP2_NO_SDIO flag ricky_wu
@ 2021-01-13 11:25 ` Ulf Hansson
0 siblings, 0 replies; 5+ messages in thread
From: Ulf Hansson @ 2021-01-13 11:25 UTC (permalink / raw)
To: 吳昊澄 Ricky
Cc: Greg Kroah-Hartman, Rui Feng, Rui Miguel Silva, Doug Anderson,
Lee Jones, linux-mmc, Linux Kernel Mailing List
On Wed, 30 Dec 2020 at 10:04, <ricky_wu@realtek.com> wrote:
>
> From: Ricky Wu <ricky_wu@realtek.com>
>
> Added flag MMC_CAP2_NO_SDIO to mmc->caps2
> Card Reader not support SDIO
>
> Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Applied for next, thanks!
Kind regards
Uffe
> ---
> drivers/mmc/host/rtsx_pci_sdmmc.c | 3 ++-
> 1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/mmc/host/rtsx_pci_sdmmc.c b/drivers/mmc/host/rtsx_pci_sdmmc.c
> index d21b99962b36..6a8b0282f272 100644
> --- a/drivers/mmc/host/rtsx_pci_sdmmc.c
> +++ b/drivers/mmc/host/rtsx_pci_sdmmc.c
> @@ -1427,7 +1427,8 @@ static void realtek_init_host(struct realtek_pci_sdmmc *host)
> MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25;
> if (pcr->rtd3_en)
> mmc->caps = mmc->caps | MMC_CAP_AGGRESSIVE_PM;
> - mmc->caps2 = MMC_CAP2_NO_PRESCAN_POWERUP | MMC_CAP2_FULL_PWR_CYCLE;
> + mmc->caps2 = MMC_CAP2_NO_PRESCAN_POWERUP | MMC_CAP2_FULL_PWR_CYCLE |
> + MMC_CAP2_NO_SDIO;
> mmc->max_current_330 = 400;
> mmc->max_current_180 = 800;
> mmc->ops = &realtek_pci_sdmmc_ops;
> --
> 2.17.1
>
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2021-01-13 11:27 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-12-30 9:04 [PATCH 1/2] mmc: rtsx: add delay before power on ricky_wu
2020-12-30 9:04 ` [PATCH 2/2] mmc: rtsx: Add MMC_CAP2_NO_SDIO flag ricky_wu
2021-01-13 11:25 ` Ulf Hansson
2021-01-13 9:58 ` [PATCH 1/2] mmc: rtsx: add delay before power on Ulf Hansson
2021-01-13 10:20 ` 吳昊澄 Ricky
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.