* [PATCH 1/7] arm64: dts: qcom: sm8350: fix typo
2021-02-12 11:55 [PATCH 0/7] arm64: dts: qcom: sm8350: additional device support Vinod Koul
@ 2021-02-12 11:55 ` Vinod Koul
2021-02-12 11:55 ` [PATCH 2/7] arm64: dts: qcom: sm8350: Add rpmhpd node Vinod Koul
` (5 subsequent siblings)
6 siblings, 0 replies; 9+ messages in thread
From: Vinod Koul @ 2021-02-12 11:55 UTC (permalink / raw)
To: Bjorn Andersson; +Cc: linux-arm-msm, Vinod Koul, Andy Gross, linux-kernel
Fix the typo s/Limaited/Limited
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 188f4011352c..b53744618102 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: BSD-3-Clause
/*
- * Copyright (c) 2020, Linaro Limaited
+ * Copyright (c) 2020, Linaro Limited
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
--
2.26.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 2/7] arm64: dts: qcom: sm8350: Add rpmhpd node
2021-02-12 11:55 [PATCH 0/7] arm64: dts: qcom: sm8350: additional device support Vinod Koul
2021-02-12 11:55 ` [PATCH 1/7] arm64: dts: qcom: sm8350: fix typo Vinod Koul
@ 2021-02-12 11:55 ` Vinod Koul
2021-02-12 11:55 ` [PATCH 3/7] arm64: dts: qcom: sm8350: Add rmtfs node Vinod Koul
` (4 subsequent siblings)
6 siblings, 0 replies; 9+ messages in thread
From: Vinod Koul @ 2021-02-12 11:55 UTC (permalink / raw)
To: Bjorn Andersson; +Cc: linux-arm-msm, Vinod Koul, Andy Gross, linux-kernel
This adds RPMH power domain found in SM8350 SoC
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 49 ++++++++++++++++++++++++++++
1 file changed, 49 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index b53744618102..0bf5cec3a2aa 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -591,6 +591,55 @@ rpmhcc: clock-controller {
clocks = <&xo_board>;
};
+ rpmhpd: power-controller {
+ compatible = "qcom,sm8350-rpmhpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmhpd_opp_table>;
+
+ rpmhpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmhpd_opp_ret: opp1 {
+ opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+ };
+
+ rpmhpd_opp_min_svs: opp2 {
+ opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+ };
+
+ rpmhpd_opp_low_svs: opp3 {
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+ };
+
+ rpmhpd_opp_svs: opp4 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+ };
+
+ rpmhpd_opp_svs_l1: opp5 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ };
+
+ rpmhpd_opp_nom: opp6 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+ };
+
+ rpmhpd_opp_nom_l1: opp7 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+ };
+
+ rpmhpd_opp_nom_l2: opp8 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+ };
+
+ rpmhpd_opp_turbo: opp9 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+ };
+
+ rpmhpd_opp_turbo_l1: opp10 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+ };
+ };
+ };
};
ufs_mem_hc: ufshc@1d84000 {
--
2.26.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 3/7] arm64: dts: qcom: sm8350: Add rmtfs node
2021-02-12 11:55 [PATCH 0/7] arm64: dts: qcom: sm8350: additional device support Vinod Koul
2021-02-12 11:55 ` [PATCH 1/7] arm64: dts: qcom: sm8350: fix typo Vinod Koul
2021-02-12 11:55 ` [PATCH 2/7] arm64: dts: qcom: sm8350: Add rpmhpd node Vinod Koul
@ 2021-02-12 11:55 ` Vinod Koul
2021-02-12 11:55 ` [PATCH 4/7] arm64: dts: qcom: sm8350: Add SMP2P nodes Vinod Koul
` (3 subsequent siblings)
6 siblings, 0 replies; 9+ messages in thread
From: Vinod Koul @ 2021-02-12 11:55 UTC (permalink / raw)
To: Bjorn Andersson; +Cc: linux-arm-msm, Vinod Koul, Andy Gross, linux-kernel
Add the rmtfs as a reserved memory node.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 0bf5cec3a2aa..faa0d0a716e6 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -257,6 +257,16 @@ pil_modem_mem: memory@8b800000 {
no-map;
};
+ rmtfs_mem: memory@9b800000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0x9b800000 0x0 0x280000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+
+
hyp_reserved_mem: memory@d0000000 {
reg = <0x0 0xd0000000 0x0 0x800000>;
no-map;
--
2.26.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 4/7] arm64: dts: qcom: sm8350: Add SMP2P nodes
2021-02-12 11:55 [PATCH 0/7] arm64: dts: qcom: sm8350: additional device support Vinod Koul
` (2 preceding siblings ...)
2021-02-12 11:55 ` [PATCH 3/7] arm64: dts: qcom: sm8350: Add rmtfs node Vinod Koul
@ 2021-02-12 11:55 ` Vinod Koul
2021-02-12 11:55 ` [PATCH 5/7] arm64: dts: qcom: sm8350: Add remoteprocs Vinod Koul
` (2 subsequent siblings)
6 siblings, 0 replies; 9+ messages in thread
From: Vinod Koul @ 2021-02-12 11:55 UTC (permalink / raw)
To: Bjorn Andersson; +Cc: linux-arm-msm, Vinod Koul, Andy Gross, linux-kernel
SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute, modem and sensor subsystems.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 96 ++++++++++++++++++++++++++++
1 file changed, 96 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index faa0d0a716e6..1ea72f30ea5a 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -304,6 +304,102 @@ smem: qcom,smem {
hwlocks = <&tcsr_mutex 3>;
};
+ smp2p-adsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <443>, <429>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_SMP2P
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_SMP2P>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <2>;
+
+ smp2p_adsp_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_adsp_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-cdsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <94>, <432>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_SMP2P
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_SMP2P>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <5>;
+
+ smp2p_cdsp_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_cdsp_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-modem {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+ IPCC_MPROC_SIGNAL_SMP2P
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_MPSS
+ IPCC_MPROC_SIGNAL_SMP2P>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ smp2p_modem_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_modem_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-slpi {
+ compatible = "qcom,smp2p";
+ qcom,smem = <481>, <430>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_SMP2P
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_SMP2P>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <3>;
+
+ smp2p_slpi_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_slpi_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
soc: soc@0 {
#address-cells = <2>;
#size-cells = <2>;
--
2.26.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 5/7] arm64: dts: qcom: sm8350: Add remoteprocs
2021-02-12 11:55 [PATCH 0/7] arm64: dts: qcom: sm8350: additional device support Vinod Koul
` (3 preceding siblings ...)
2021-02-12 11:55 ` [PATCH 4/7] arm64: dts: qcom: sm8350: Add SMP2P nodes Vinod Koul
@ 2021-02-12 11:55 ` Vinod Koul
2021-02-12 11:55 ` [PATCH 6/7] arm64: dts: qcom: sm8350-mtp: Enable remoteprocs Vinod Koul
2021-02-12 11:55 ` [PATCH 7/7] arm64: dts: qcom: sm8350: Use enums for GCC Vinod Koul
6 siblings, 0 replies; 9+ messages in thread
From: Vinod Koul @ 2021-02-12 11:55 UTC (permalink / raw)
To: Bjorn Andersson; +Cc: linux-arm-msm, Vinod Koul, Andy Gross, linux-kernel
Add remoteproc nodes for the audio, compute and sensor cores, define
glink for each one.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 158 +++++++++++++++++++++++++++
1 file changed, 158 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 1ea72f30ea5a..6e366653eeab 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -562,6 +562,46 @@ tcsr_mutex: hwlock@1f40000 {
#hwlock-cells = <1>;
};
+ mpss: remoteproc@4080000 {
+ compatible = "qcom,sm8350-mpss-pas";
+ reg = <0x0 0x04080000 0x0 0x4040>;
+
+ interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_modem_in 7 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready", "handover",
+ "stop-ack", "shutdown-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_MODEM>,
+ <&rpmhpd SM8350_CX>,
+ <&rpmhpd SM8350_MSS>;
+ power-domain-names = "load_state", "cx", "mss";
+
+ memory-region = <&pil_modem_mem>;
+
+ qcom,smem-states = <&smp2p_modem_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_MPSS
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+ interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
+ label = "modem";
+ qcom,remote-pid = <1>;
+ };
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sm8350-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
@@ -824,6 +864,85 @@ ufs_mem_phy_lanes: lanes@1d87400 {
};
};
+ slpi: remoteproc@5c00000 {
+ compatible = "qcom,sm8350-slpi-pas";
+ reg = <0 0x05c00000 0 0x4000>;
+
+ interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>,
+ <&rpmhpd SM8350_LCX>,
+ <&rpmhpd SM8350_LMX>;
+ power-domain-names = "load_state", "lcx", "lmx";
+
+ memory-region = <&pil_slpi_mem>;
+
+ qcom,smem-states = <&smp2p_slpi_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "slpi";
+ qcom,remote-pid = <3>;
+
+ };
+ };
+
+ cdsp: remoteproc@98900000 {
+ compatible = "qcom,sm8350-cdsp-pas";
+ reg = <0 0x098900000 0 0x1400000>;
+
+ interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>,
+ <&rpmhpd SM8350_CX>,
+ <&rpmhpd SM8350_MXC>;
+ power-domain-names = "load_state", "cx", "mxc";
+
+ memory-region = <&pil_cdsp_mem>;
+
+ qcom,smem-states = <&smp2p_cdsp_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "cdsp";
+ qcom,remote-pid = <5>;
+ };
+ };
+
usb_1_hsphy: phy@88e3000 {
compatible = "qcom,sm8350-usb-hs-phy",
"qcom,usb-snps-hs-7nm-phy";
@@ -1002,6 +1121,45 @@ usb_2_dwc3: dwc3@a800000 {
phy-names = "usb2-phy", "usb3-phy";
};
};
+
+ adsp: remoteproc@17300000 {
+ compatible = "qcom,sm8350-adsp-pas";
+ reg = <0 0x17300000 0 0x100>;
+
+ interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>,
+ <&rpmhpd SM8350_LCX>,
+ <&rpmhpd SM8350_LMX>;
+ power-domain-names = "load_state", "lcx", "lmx";
+
+ memory-region = <&pil_adsp_mem>;
+
+ qcom,smem-states = <&smp2p_adsp_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "lpass";
+ qcom,remote-pid = <2>;
+ };
+ };
};
timer {
--
2.26.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 6/7] arm64: dts: qcom: sm8350-mtp: Enable remoteprocs
2021-02-12 11:55 [PATCH 0/7] arm64: dts: qcom: sm8350: additional device support Vinod Koul
` (4 preceding siblings ...)
2021-02-12 11:55 ` [PATCH 5/7] arm64: dts: qcom: sm8350: Add remoteprocs Vinod Koul
@ 2021-02-12 11:55 ` Vinod Koul
2021-02-12 11:55 ` [PATCH 7/7] arm64: dts: qcom: sm8350: Use enums for GCC Vinod Koul
6 siblings, 0 replies; 9+ messages in thread
From: Vinod Koul @ 2021-02-12 11:55 UTC (permalink / raw)
To: Bjorn Andersson; +Cc: linux-arm-msm, Vinod Koul, Andy Gross, linux-kernel
This enabled the four remoteprocs found in SM8350, audio, compute, modem
and sensor for MTP platform and adds firmware for them.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8350-mtp.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts
index e544fe6b421f..98a517edd442 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts
@@ -32,6 +32,11 @@ vph_pwr: vph-pwr-regulator {
};
};
+&adsp {
+ status = "okay";
+ firmware-name = "qcom/sm8350/adsp.mbn";
+};
+
&apps_rsc {
pm8350-rpmh-regulators {
compatible = "qcom,pm8350-rpmh-regulators";
@@ -265,10 +270,25 @@ vreg_l13c_3p0: ldo13 {
};
};
+&cdsp {
+ status = "okay";
+ firmware-name = "qcom/sm8350/cdsp.mbn";
+};
+
+&mpss {
+ status = "okay";
+ firmware-name = "qcom/sm8350/modem.mbn";
+};
+
&qupv3_id_1 {
status = "okay";
};
+&slpi {
+ status = "okay";
+ firmware-name = "qcom/sm8350/slpi.mbn";
+};
+
&tlmm {
gpio-reserved-ranges = <52 8>;
};
--
2.26.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 7/7] arm64: dts: qcom: sm8350: Use enums for GCC
2021-02-12 11:55 [PATCH 0/7] arm64: dts: qcom: sm8350: additional device support Vinod Koul
` (5 preceding siblings ...)
2021-02-12 11:55 ` [PATCH 6/7] arm64: dts: qcom: sm8350-mtp: Enable remoteprocs Vinod Koul
@ 2021-02-12 11:55 ` Vinod Koul
2021-02-16 11:17 ` [PATCH 7/6] arm64: dts: qcom: sm8350: Add cpufreq node Vinod Koul
6 siblings, 1 reply; 9+ messages in thread
From: Vinod Koul @ 2021-02-12 11:55 UTC (permalink / raw)
To: Bjorn Andersson; +Cc: linux-arm-msm, Vinod Koul, Andy Gross, linux-kernel
Now that we have GCC define, use the enums instead of numbers in the DTS
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 91 ++++++++++++++--------------
1 file changed, 46 insertions(+), 45 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 6e366653eeab..d19ed7b5aae0 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -4,6 +4,7 @@
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-sm8350.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/power/qcom-aoss-qmp.h>
@@ -430,8 +431,8 @@ qupv3_id_1: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x009c0000 0x0 0x6000>;
clock-names = "m-ahb", "s-ahb";
- clocks = <&gcc 121>,
- <&gcc 122>;
+ clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
@@ -441,7 +442,7 @@ uart2: serial@98c000 {
compatible = "qcom,geni-debug-uart";
reg = <0 0x0098c000 0 0x4000>;
clock-names = "se";
- clocks = <&gcc 83>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_uart3_default_state>;
interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
@@ -797,10 +798,10 @@ ufs_mem_hc: ufshc@1d84000 {
phy-names = "ufsphy";
lanes-per-direction = <2>;
#reset-cells = <1>;
- resets = <&gcc 25>;
+ resets = <&gcc GCC_UFS_PHY_BCR>;
reset-names = "rst";
- power-domains = <&gcc 3>;
+ power-domains = <&gcc UFS_PHY_GDSC>;
iommus = <&apps_smmu 0xe0 0x0>;
@@ -816,14 +817,14 @@ ufs_mem_hc: ufshc@1d84000 {
"rx_lane1_sync_clk";
clocks =
<&rpmhcc RPMH_CXO_CLK>,
- <&gcc 155>,
- <&gcc 16>,
- <&gcc 154>,
- <&gcc 170>,
+ <&gcc GCC_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_UFS_PHY_AHB_CLK>,
+ <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
- <&gcc 168>,
- <&gcc 164>,
- <&gcc 166>;
+ <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
freq-table-hz =
<75000000 300000000>,
<75000000 300000000>,
@@ -847,7 +848,7 @@ ufs_mem_phy: phy@1d87000 {
clock-names = "ref",
"ref_aux";
clocks = <&rpmhcc RPMH_CXO_CLK>,
- <&gcc 161>;
+ <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
resets = <&ufs_mem_hc 0>;
reset-names = "ufsphy";
@@ -953,7 +954,7 @@ usb_1_hsphy: phy@88e3000 {
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "ref";
- resets = <&gcc 20>;
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
};
usb_2_hsphy: phy@88e4000 {
@@ -966,7 +967,7 @@ usb_2_hsphy: phy@88e4000 {
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "ref";
- resets = <&gcc 21>;
+ resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
};
usb_1_qmpphy: phy-wrapper@88e9000 {
@@ -980,13 +981,13 @@ usb_1_qmpphy: phy-wrapper@88e9000 {
#size-cells = <2>;
ranges;
- clocks = <&gcc 187>,
+ clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
- <&gcc 189>;
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
clock-names = "aux", "ref_clk_src", "com_aux";
- resets = <&gcc 28>,
- <&gcc 30>;
+ resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+ <&gcc GCC_USB3_PHY_PRIM_BCR>;
reset-names = "phy", "common";
usb_1_ssphy: phy@88e9200 {
@@ -998,7 +999,7 @@ usb_1_ssphy: phy@88e9200 {
<0 0x088e9a00 0 0x100>;
#phy-cells = <0>;
#clock-cells = <1>;
- clocks = <&gcc 190>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
clock-names = "pipe0";
clock-output-names = "usb3_phy_pipe_clk_src";
};
@@ -1013,14 +1014,14 @@ usb_2_qmpphy: phy-wrapper@88eb000 {
#size-cells = <2>;
ranges;
- clocks = <&gcc 193>,
+ clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
- <&gcc 192>,
- <&gcc 195>;
+ <&gcc GCC_USB3_SEC_CLKREF_EN>,
+ <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
clock-names = "aux", "ref_clk_src", "ref", "com_aux";
- resets = <&gcc 33>,
- <&gcc 31>;
+ resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+ <&gcc GCC_USB3_PHY_SEC_BCR>;
reset-names = "phy", "common";
usb_2_ssphy: phy@88ebe00 {
@@ -1029,7 +1030,7 @@ usb_2_ssphy: phy@88ebe00 {
<0 0x088eb200 0 0x1100>;
#phy-cells = <0>;
#clock-cells = <1>;
- clocks = <&gcc 196>;
+ clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
clock-names = "pipe0";
clock-output-names = "usb3_uni_phy_pipe_clk_src";
};
@@ -1043,16 +1044,16 @@ usb_1: usb@a6f8800 {
#size-cells = <2>;
ranges;
- clocks = <&gcc 23>,
- <&gcc 173>,
- <&gcc 18>,
- <&gcc 176>,
- <&gcc 179>;
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
clock-names = "cfg_noc", "core", "iface", "mock_utmi",
"sleep";
- assigned-clocks = <&gcc 176>,
- <&gcc 173>;
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
assigned-clock-rates = <19200000>, <200000000>;
interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
@@ -1062,9 +1063,9 @@ usb_1: usb@a6f8800 {
interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
"dm_hs_phy_irq", "ss_phy_irq";
- power-domains = <&gcc 4>;
+ power-domains = <&gcc USB30_PRIM_GDSC>;
- resets = <&gcc 26>;
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
usb_1_dwc3: dwc3@a600000 {
compatible = "snps,dwc3";
@@ -1086,17 +1087,17 @@ usb_2: usb@a8f8800 {
#size-cells = <2>;
ranges;
- clocks = <&gcc 24>,
- <&gcc 180>,
- <&gcc 19>,
- <&gcc 183>,
- <&gcc 186>,
- <&gcc 192>;
+ clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_EN>;
clock-names = "cfg_noc", "core", "iface", "mock_utmi",
"sleep", "xo";
- assigned-clocks = <&gcc 183>,
- <&gcc 180>;
+ assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>;
assigned-clock-rates = <19200000>, <200000000>;
interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
@@ -1106,9 +1107,9 @@ usb_2: usb@a8f8800 {
interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
"dm_hs_phy_irq", "ss_phy_irq";
- power-domains = <&gcc 5>;
+ power-domains = <&gcc USB30_SEC_GDSC>;
- resets = <&gcc 27>;
+ resets = <&gcc GCC_USB30_SEC_BCR>;
usb_2_dwc3: dwc3@a800000 {
compatible = "snps,dwc3";
--
2.26.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 7/6] arm64: dts: qcom: sm8350: Add cpufreq node
2021-02-12 11:55 ` [PATCH 7/7] arm64: dts: qcom: sm8350: Use enums for GCC Vinod Koul
@ 2021-02-16 11:17 ` Vinod Koul
0 siblings, 0 replies; 9+ messages in thread
From: Vinod Koul @ 2021-02-16 11:17 UTC (permalink / raw)
To: Bjorn Andersson; +Cc: linux-arm-msm, Vinod Koul, Andy Gross, linux-kernel
Add cpufreq node and reference it for the CPUs.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
- appended this to dts patch series
arch/arm64/boot/dts/qcom/sm8350.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 1aa2a9e00a75..91d4cbbe38dc 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -45,6 +45,7 @@ CPU0: cpu@0 {
reg = <0x0 0x0>;
enable-method = "psci";
next-level-cache = <&L2_0>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
L2_0: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
@@ -60,6 +61,7 @@ CPU1: cpu@100 {
reg = <0x0 0x100>;
enable-method = "psci";
next-level-cache = <&L2_100>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
L2_100: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
@@ -72,6 +74,7 @@ CPU2: cpu@200 {
reg = <0x0 0x200>;
enable-method = "psci";
next-level-cache = <&L2_200>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
L2_200: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
@@ -84,6 +87,7 @@ CPU3: cpu@300 {
reg = <0x0 0x300>;
enable-method = "psci";
next-level-cache = <&L2_300>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
L2_300: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
@@ -96,6 +100,7 @@ CPU4: cpu@400 {
reg = <0x0 0x400>;
enable-method = "psci";
next-level-cache = <&L2_400>;
+ qcom,freq-domain = <&cpufreq_hw 1>;
L2_400: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
@@ -108,6 +113,7 @@ CPU5: cpu@500 {
reg = <0x0 0x500>;
enable-method = "psci";
next-level-cache = <&L2_500>;
+ qcom,freq-domain = <&cpufreq_hw 1>;
L2_500: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
@@ -121,6 +127,7 @@ CPU6: cpu@600 {
reg = <0x0 0x600>;
enable-method = "psci";
next-level-cache = <&L2_600>;
+ qcom,freq-domain = <&cpufreq_hw 1>;
L2_600: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
@@ -133,6 +140,7 @@ CPU7: cpu@700 {
reg = <0x0 0x700>;
enable-method = "psci";
next-level-cache = <&L2_700>;
+ qcom,freq-domain = <&cpufreq_hw 2>;
L2_700: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
@@ -852,6 +860,19 @@ apps_bcm_voter: bcm_voter {
};
};
+ cpufreq_hw: cpufreq@18591000 {
+ compatible = "qcom,sm8350-cpufreq-epss", "qcom,cpufreq-epss";
+ reg = <0 0x18591000 0 0x1000>,
+ <0 0x18592000 0 0x1000>,
+ <0 0x18593000 0 0x1000>;
+ reg-names = "freq-domain0", "freq-domain1", "freq-domain2";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
+ clock-names = "xo", "alternate";
+
+ #freq-domain-cells = <1>;
+ };
+
ufs_mem_hc: ufshc@1d84000 {
compatible = "qcom,sm8350-ufshc", "qcom,ufshc",
"jedec,ufs-2.0";
--
2.26.2
^ permalink raw reply related [flat|nested] 9+ messages in thread