* Kernel panic caused by plugging in a sata cable on a a minipcie-sata board
@ 2021-01-27 21:27 Rötti
2021-03-07 12:38 ` Rötti
0 siblings, 1 reply; 6+ messages in thread
From: Rötti @ 2021-01-27 21:27 UTC (permalink / raw)
To: Linux ide
Hello everyone,
I own two ESPRESSOBin boards V5.
And to both I attached an XCSOURCE® MiniPCIe Sata3.0 AC696 extension
card via MiniPCIe.
This is the link to amazon: https://www.amazon.de/dp/B06XRG2TGV
I tested several images from
https://www.armbian.com/espressobin/#kernels-archive-all
Tested Kernels 8 weeks ago + the latest two this week:
- 5.10.09-mvebu64 #21.02.0-hirsute (trunk) <-- works not
- 5.08.18-mvebu64 #20.11.6-bionic <-- works not
- 5.08.18-mvebu64 #20.11.3-focal <-- works not
- 5.08.18-mvebu64 #20.11.3-bionic <-- works not
- 5.08.06-mvebu64 #20.08.2-focal <-- works not
- 4.14.135-mvebu64 #19.11.3-bionic <-- works
Here is the whole UART-dump:
TIM-1.0
WTMI-devel-18.12.0-a0a1cb8
WTMI: system early-init
SVC REV: 3, CPU VDD voltage: 1.155V
NOTICE: Booting Trusted Firmware
NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
NOTICE: BL1: Built : 09:48:09, Feb 20 2019
NOTICE: BL1: Booting BL2
NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
NOTICE: BL2: Built : 09:48:10, Feb 20 2019
NOTICE: BL1: Booting BL31
NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
NOTICE: BL31: Built : 09:4
U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04
+0100)
Model: Marvell Armada 3720 Community Board ESPRESSOBin
CPU 1000 [MHz]
L2 800 [MHz]
TClock 200 [MHz]
DDR 800 [MHz]
DRAM: 2 GiB
Comphy chip #0:
Comphy-0: USB3 5 Gbps
Comphy-1: PEX0 2.5 Gbps
Comphy-2: SATA0 6 Gbps
Target spinup took 0 ms.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs
PCIE-0: Link up
MMC: sdhci@d0000: 0, sdhci@d8000: 1
Loading Environment from SPI Flash... SF: Detected w25q32dw with page
size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Model: Marvell Armada 3720 Community Board ESPRESSOBin
Net: eth0: neta@30000 [PRIME]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000104 NbrPorts 2
Starting the controller
USB XHCI 1.00
USB1: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 10750023 Bytes = 10.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 06000000
Booting using the fdt blob at 0x6000000
Loading Ramdisk to 7ebea000, end 7f62a847 ... OK
Using Device Tree in place at 0000000006000000, end 00000000060059cd
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.8.18-mvebu64 (root@beast)
(aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture
8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321)
#20.11.3 SMP PREEMPT Fri Dec 11 21:10:52 CET 2020
[ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
[ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000
(options '')
[ 0.000000] printk: bootconsole [ar3700_uart0] enabled
Loading, please wait...
Starting version 245.4-4ubuntu3.3
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top
... done.
Begin: Running /scripts/local-premount ... Scanning for Btrfs
filesystems
done.
Begin: Will now check root file system ... fsck from util-linux 2.34
[/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0
/dev/mmcblk0p1
/dev/mmcblk0p1: clean, 41739/1828336 files, 439779/7502824 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 3.694604] Internal error: synchronous external abort: 96000210 [#1]
PREEMPT SMP
[ 3.699465] Modules linked in: tag_edsa mv88e6xxx dsa_core bridge stp
llc phy_mvebu_a3700_comphy
[ 3.708518] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
5.8.18-mvebu64 #20.11.3
[ 3.716037] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
[ 3.722685] Workqueue: events free_work
[ 3.726614] pstate: 00000085 (nzcv daIf -PAN -UAO BTYPE=--)
[ 3.732352] pc : ahci_single_level_irq_intr+0x1c/0x90
[ 3.737549] lr : __handle_irq_event_percpu+0x5c/0x168
[ 3.742737] sp : ffffffc0113bbd10
[ 3.746142] x29: ffffffc0113bbd10 x28: ffffff807d48b700
[ 3.751608] x27: 0000000000000060 x26: ffffffc010f085e8
[ 3.757073] x25: ffffffc0113075a5 x24: ffffff8079101800
[ 3.762539] x23: 000000000000002d x22: ffffffc0113bbdd4
[ 3.768004] x21: 0000000000000000 x20: ffffffc011465008
[ 3.773470] x19: ffffff8079381600 x18: 0000000000000000
[ 3.778936] x17: 0000000000000000 x16: 0000000000000000
[ 3.784401] x15: 000000d2c010fc50 x14: 0000000000000323
[ 3.789867] x13: 00000000000002d4 x12: 0000000000000000
[ 3.795332] x11: 0000000000000040 x10: ffffffc011282dd8
[ 3.800798] x9 : ffffffc011282dd0 x8 : ffffff807d000270
[ 3.806263] x7 : 0000000000000000 x6 : 0000000000000000
[ 3.811729] x5 : ffffffc06ea93000 x4 : ffffffc0113bbe10
[ 3.817196] x3 : ffffffc06ea93000 x2 : ffffff8079101a80
[ 3.822661] x1 : ffffff8078803e00 x0 : 000000000000002d
[ 3.828126] Call trace:
[ 3.830642] ahci_single_level_irq_intr+0x1c/0x90
[ 3.835478] __handle_irq_event_percpu+0x5c/0x168
[ 3.840315] handle_irq_event_percpu+0x38/0x90
[ 3.844885] handle_irq_event+0x48/0xe0
[ 3.848828] handle_simple_irq+0x94/0xd0
[ 3.852860] generic_handle_irq+0x30/0x48
[ 3.856985] advk_pcie_irq_handler+0x214/0x240
[ 3.861552] __handle_irq_event_percpu+0x5c/0x168
[ 3.866389] handle_irq_event_percpu+0x38/0x90
[ 3.870959] handle_irq_event+0x48/0xe0
[ 3.874900] handle_fasteoi_irq+0xb8/0x170
[ 3.879112] generic_handle_irq+0x30/0x48
[ 3.883234] __handle_domain_irq+0x64/0xc0
[ 3.887447] gic_handle_irq+0xc8/0x168
[ 3.891298] el1_irq+0xb8/0x180
[ 3.894524] unmap_kernel_range_noflush+0x128/0x188
[ 3.899540] remove_vm_area+0xac/0xd0
[ 3.903303] __vunmap+0x48/0x298
[ 3.906618] free_work+0x44/0x60
[ 3.909937] process_one_work+0x1e8/0x360
[ 3.914057] worker_thread+0x44/0x480
[ 3.917820] kthread+0x154/0x158
[ 3.921135] ret_from_fork+0x10/0x34
[ 3.924812] Code: a90153f3 f9401022 f9400854 91002294 (b9400293)
[ 3.931087] ---[ end trace 98b323414bb99c99 ]---
[ 3.935829] Kernel panic - not syncing: Fatal exception in interrupt
[ 3.942368] SMP: stopping secondary CPUs
[ 3.946403] Kernel Offset: disabled
[ 3.949985] CPU features: 0x240002,2000200c
[ 3.954283] Memory Limit: none
[ 3.957424] ---[ end Kernel panic - not syncing: Fatal exception in
interrupt ]---
The boards boots up if I don't plug in any SATA HDDs into the extension
card.
I hope this helps. If you need any other information just let me know,
I'm absolutely willing to help. But I have no clue of kernel
patching/compiling etc. Sorry!
Thank you very, very much in advance! You're doing an awesome job.
Sincerely Rötti
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Kernel panic caused by plugging in a sata cable on a a minipcie-sata board
2021-01-27 21:27 Kernel panic caused by plugging in a sata cable on a a minipcie-sata board Rötti
@ 2021-03-07 12:38 ` Rötti
2021-03-08 9:54 ` Pali Rohár
0 siblings, 1 reply; 6+ messages in thread
From: Rötti @ 2021-03-07 12:38 UTC (permalink / raw)
To: Linux ide
Hello everyone,
I'm sorry, I've been missing some information:
Here is the output of lspci -nn -vv to correctly identify type of your
PCIe SATA controller:
00:00.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device
[1b4b:0100] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 52
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: e9001000-e9001fff [size=4K]
Memory behind bridge: e8000000-e80fffff [size=1M]
Prefetchable memory behind bridge: [disabled]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
Expansion ROM at e8100000 [virtual] [disabled] [size=2K]
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset-
FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 512 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Exit Latency L0s <128ns, L1 <2us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk- DLActive- BWMgmt-
ABWMgmt-
RootCap: CRSVisible-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna+ CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Kernel driver in use: pcieport
01:00.0 SATA controller [0106]: ASMedia Technology Inc. ASM1062 Serial
ATA Controller [1b21:0612] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
[1b21:1060]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 53
Region 0: I/O ports at 1020 [size=8]
Region 1: I/O ports at 1030 [size=4]
Region 2: I/O ports at 1028 [size=8]
Region 3: I/O ports at 1034 [size=4]
Region 4: I/O ports at 1000 [size=32]
Region 5: Memory at e8010000 (32-bit, non-prefetchable)
[size=512]
Expansion ROM at e8000000 [virtual] [disabled] [size=64K]
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: 7f044770 Data: 0035
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s
<1us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 512 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq-
AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM not
supported
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt-
ABWMgmt-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+,
NROPrPrP-, LTR-
10BitTagComp-, 10BitTagReq-, OBFF Not
Supported, ExtFmt-, EETLPPrefix-
EmergencyPowerReduction Not Supported,
EmergencyPowerReductionInit-
FRS-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-,
LTR-, OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-,
LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1
RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: ahci
Kind regards, Rötti!
Am 27.01.2021 22:27 schrieb Rötti:
> Hello everyone,
>
> I own two ESPRESSOBin boards V5.
>
> And to both I attached an XCSOURCE® MiniPCIe Sata3.0 AC696 extension
> card via MiniPCIe.
>
> This is the link to amazon: https://www.amazon.de/dp/B06XRG2TGV
>
> I tested several images from
> https://www.armbian.com/espressobin/#kernels-archive-all
>
> Tested Kernels 8 weeks ago + the latest two this week:
> - 5.10.09-mvebu64 #21.02.0-hirsute (trunk) <-- works not
> - 5.08.18-mvebu64 #20.11.6-bionic <-- works not
> - 5.08.18-mvebu64 #20.11.3-focal <-- works not
> - 5.08.18-mvebu64 #20.11.3-bionic <-- works not
> - 5.08.06-mvebu64 #20.08.2-focal <-- works not
> - 4.14.135-mvebu64 #19.11.3-bionic <-- works
>
>
> Here is the whole UART-dump:
>
> TIM-1.0
> WTMI-devel-18.12.0-a0a1cb8
> WTMI: system early-init
> SVC REV: 3, CPU VDD voltage: 1.155V
> NOTICE: Booting Trusted Firmware
> NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> NOTICE: BL1: Built : 09:48:09, Feb 20 2019
> NOTICE: BL1: Booting BL2
> NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> NOTICE: BL2: Built : 09:48:10, Feb 20 2019
> NOTICE: BL1: Booting BL31
> NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> NOTICE: BL31: Built : 09:4
>
> U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04
> +0100)
>
> Model: Marvell Armada 3720 Community Board ESPRESSOBin
> CPU 1000 [MHz]
> L2 800 [MHz]
> TClock 200 [MHz]
> DDR 800 [MHz]
> DRAM: 2 GiB
> Comphy chip #0:
> Comphy-0: USB3 5 Gbps
> Comphy-1: PEX0 2.5 Gbps
> Comphy-2: SATA0 6 Gbps
> Target spinup took 0 ms.
> AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
> flags: ncq led only pmp fbss pio slum part sxs
> PCIE-0: Link up
> MMC: sdhci@d0000: 0, sdhci@d8000: 1
> Loading Environment from SPI Flash... SF: Detected w25q32dw with page
> size 256 Bytes, erase size 4 KiB, total 4 MiB
> OK
> Model: Marvell Armada 3720 Community Board ESPRESSOBin
> Net: eth0: neta@30000 [PRIME]
> Hit any key to stop autoboot: 0
> starting USB...
> USB0: Register 2000104 NbrPorts 2
> Starting the controller
> USB XHCI 1.00
> USB1: USB EHCI 1.00
> scanning bus 0 for devices... 1 USB Device(s) found
> scanning bus 1 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 0 Storage Device(s) found
>
> ## Loading init Ramdisk from Legacy Image at 01100000 ...
> Image Name: uInitrd
> Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
> Data Size: 10750023 Bytes = 10.3 MiB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
> ## Flattened Device Tree blob at 06000000
> Booting using the fdt blob at 0x6000000
> Loading Ramdisk to 7ebea000, end 7f62a847 ... OK
> Using Device Tree in place at 0000000006000000, end 00000000060059cd
>
> Starting kernel ...
>
> [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
> [ 0.000000] Linux version 5.8.18-mvebu64 (root@beast)
> (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture
> 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
> A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321)
> #20.11.3 SMP PREEMPT Fri Dec 11 21:10:52 CET 2020
> [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
> [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000
> (options '')
> [ 0.000000] printk: bootconsole [ar3700_uart0] enabled
> Loading, please wait...
> Starting version 245.4-4ubuntu3.3
> Begin: Loading essential drivers ... done.
> Begin: Running /scripts/init-premount ... done.
> Begin: Mounting root file system ... Begin: Running /scripts/local-top
> ... done.
> Begin: Running /scripts/local-premount ... Scanning for Btrfs
> filesystems
> done.
> Begin: Will now check root file system ... fsck from util-linux 2.34
> [/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0
> /dev/mmcblk0p1
> /dev/mmcblk0p1: clean, 41739/1828336 files, 439779/7502824 blocks
> done.
> done.
> Begin: Running /scripts/local-bottom ... done.
> Begin: Running /scripts/init-bottom ... done.
> [ 3.694604] Internal error: synchronous external abort: 96000210
> [#1] PREEMPT SMP
> [ 3.699465] Modules linked in: tag_edsa mv88e6xxx dsa_core bridge
> stp llc phy_mvebu_a3700_comphy
> [ 3.708518] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
> 5.8.18-mvebu64 #20.11.3
> [ 3.716037] Hardware name: Globalscale Marvell ESPRESSOBin Board
> (DT)
> [ 3.722685] Workqueue: events free_work
> [ 3.726614] pstate: 00000085 (nzcv daIf -PAN -UAO BTYPE=--)
> [ 3.732352] pc : ahci_single_level_irq_intr+0x1c/0x90
> [ 3.737549] lr : __handle_irq_event_percpu+0x5c/0x168
> [ 3.742737] sp : ffffffc0113bbd10
> [ 3.746142] x29: ffffffc0113bbd10 x28: ffffff807d48b700
> [ 3.751608] x27: 0000000000000060 x26: ffffffc010f085e8
> [ 3.757073] x25: ffffffc0113075a5 x24: ffffff8079101800
> [ 3.762539] x23: 000000000000002d x22: ffffffc0113bbdd4
> [ 3.768004] x21: 0000000000000000 x20: ffffffc011465008
> [ 3.773470] x19: ffffff8079381600 x18: 0000000000000000
> [ 3.778936] x17: 0000000000000000 x16: 0000000000000000
> [ 3.784401] x15: 000000d2c010fc50 x14: 0000000000000323
> [ 3.789867] x13: 00000000000002d4 x12: 0000000000000000
> [ 3.795332] x11: 0000000000000040 x10: ffffffc011282dd8
> [ 3.800798] x9 : ffffffc011282dd0 x8 : ffffff807d000270
> [ 3.806263] x7 : 0000000000000000 x6 : 0000000000000000
> [ 3.811729] x5 : ffffffc06ea93000 x4 : ffffffc0113bbe10
> [ 3.817196] x3 : ffffffc06ea93000 x2 : ffffff8079101a80
> [ 3.822661] x1 : ffffff8078803e00 x0 : 000000000000002d
> [ 3.828126] Call trace:
> [ 3.830642] ahci_single_level_irq_intr+0x1c/0x90
> [ 3.835478] __handle_irq_event_percpu+0x5c/0x168
> [ 3.840315] handle_irq_event_percpu+0x38/0x90
> [ 3.844885] handle_irq_event+0x48/0xe0
> [ 3.848828] handle_simple_irq+0x94/0xd0
> [ 3.852860] generic_handle_irq+0x30/0x48
> [ 3.856985] advk_pcie_irq_handler+0x214/0x240
> [ 3.861552] __handle_irq_event_percpu+0x5c/0x168
> [ 3.866389] handle_irq_event_percpu+0x38/0x90
> [ 3.870959] handle_irq_event+0x48/0xe0
> [ 3.874900] handle_fasteoi_irq+0xb8/0x170
> [ 3.879112] generic_handle_irq+0x30/0x48
> [ 3.883234] __handle_domain_irq+0x64/0xc0
> [ 3.887447] gic_handle_irq+0xc8/0x168
> [ 3.891298] el1_irq+0xb8/0x180
> [ 3.894524] unmap_kernel_range_noflush+0x128/0x188
> [ 3.899540] remove_vm_area+0xac/0xd0
> [ 3.903303] __vunmap+0x48/0x298
> [ 3.906618] free_work+0x44/0x60
> [ 3.909937] process_one_work+0x1e8/0x360
> [ 3.914057] worker_thread+0x44/0x480
> [ 3.917820] kthread+0x154/0x158
> [ 3.921135] ret_from_fork+0x10/0x34
> [ 3.924812] Code: a90153f3 f9401022 f9400854 91002294 (b9400293)
> [ 3.931087] ---[ end trace 98b323414bb99c99 ]---
> [ 3.935829] Kernel panic - not syncing: Fatal exception in interrupt
> [ 3.942368] SMP: stopping secondary CPUs
> [ 3.946403] Kernel Offset: disabled
> [ 3.949985] CPU features: 0x240002,2000200c
> [ 3.954283] Memory Limit: none
> [ 3.957424] ---[ end Kernel panic - not syncing: Fatal exception in
> interrupt ]---
>
> The boards boots up if I don't plug in any SATA HDDs into the extension
> card.
>
> I hope this helps. If you need any other information just let me know,
> I'm absolutely willing to help. But I have no clue of kernel
> patching/compiling etc. Sorry!
>
> Thank you very, very much in advance! You're doing an awesome job.
>
> Sincerely Rötti
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Kernel panic caused by plugging in a sata cable on a a minipcie-sata board
2021-03-07 12:38 ` Rötti
@ 2021-03-08 9:54 ` Pali Rohár
2021-03-15 19:32 ` Pali Rohár
0 siblings, 1 reply; 6+ messages in thread
From: Pali Rohár @ 2021-03-08 9:54 UTC (permalink / raw)
To: linux-pci, linux-ide, Rötti
Adding linux-pci ML to the loop.
Any idea where can be the issue? Problematic interrupt is triggered from
the pci-aardvark.c driver. But I guess that issue can be in ahci code.
On Sunday 07 March 2021 13:38:03 Rötti wrote:
> Hello everyone,
>
> I'm sorry, I've been missing some information:
>
> Here is the output of lspci -nn -vv to correctly identify type of your PCIe
> SATA controller:
>
> 00:00.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [1b4b:0100]
> (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 52
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: e9001000-e9001fff [size=4K]
> Memory behind bridge: e8000000-e80fffff [size=1M]
> Prefetchable memory behind bridge: [disabled]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> Expansion ROM at e8100000 [virtual] [disabled] [size=2K]
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 512 bytes, PhantFunc 0
> ExtTag- RBE+
> DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 512 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr-
> TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
> Latency L0s <128ns, L1 <2us
> ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
> TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
> RootCap: CRSVisible-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
> CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> Kernel driver in use: pcieport
>
> 01:00.0 SATA controller [0106]: ASMedia Technology Inc. ASM1062 Serial ATA
> Controller [1b21:0612] (rev 02) (prog-if 01 [AHCI 1.0])
> Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
> [1b21:1060]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 53
> Region 0: I/O ports at 1020 [size=8]
> Region 1: I/O ports at 1030 [size=4]
> Region 2: I/O ports at 1028 [size=8]
> Region 3: I/O ports at 1034 [size=4]
> Region 4: I/O ports at 1000 [size=32]
> Region 5: Memory at e8010000 (32-bit, non-prefetchable) [size=512]
> Expansion ROM at e8000000 [virtual] [disabled] [size=64K]
> Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Address: 7f044770 Data: 0035
> Capabilities: [78] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
> DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us,
> L1 <8us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 512 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr-
> TransPend-
> LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM not supported
> ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
> TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Range ABC, TimeoutDis+,
> NROPrPrP-, LTR-
> 10BitTagComp-, 10BitTagReq-, OBFF Not Supported,
> ExtFmt-, EETLPPrefix-
> EmergencyPowerReduction Not Supported,
> EmergencyPowerReductionInit-
> FRS-
> AtomicOpsCap: 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-,
> LTR-, OBFF Disabled
> AtomicOpsCtl: ReqEn-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
> SpeedDis-
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB,
> EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-,
> LinkEqualizationRequest-
> Capabilities: [100 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
> WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Kernel driver in use: ahci
>
>
> Kind regards, Rötti!
>
> Am 27.01.2021 22:27 schrieb Rötti:
> > Hello everyone,
> >
> > I own two ESPRESSOBin boards V5.
> >
> > And to both I attached an XCSOURCE® MiniPCIe Sata3.0 AC696 extension
> > card via MiniPCIe.
> >
> > This is the link to amazon: https://www.amazon.de/dp/B06XRG2TGV
> >
> > I tested several images from
> > https://www.armbian.com/espressobin/#kernels-archive-all
> >
> > Tested Kernels 8 weeks ago + the latest two this week:
> > - 5.10.09-mvebu64 #21.02.0-hirsute (trunk) <-- works not
> > - 5.08.18-mvebu64 #20.11.6-bionic <-- works not
> > - 5.08.18-mvebu64 #20.11.3-focal <-- works not
> > - 5.08.18-mvebu64 #20.11.3-bionic <-- works not
> > - 5.08.06-mvebu64 #20.08.2-focal <-- works not
> > - 4.14.135-mvebu64 #19.11.3-bionic <-- works
> >
> >
> > Here is the whole UART-dump:
> >
> > TIM-1.0
> > WTMI-devel-18.12.0-a0a1cb8
> > WTMI: system early-init
> > SVC REV: 3, CPU VDD voltage: 1.155V
> > NOTICE: Booting Trusted Firmware
> > NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> > NOTICE: BL1: Built : 09:48:09, Feb 20 2019
> > NOTICE: BL1: Booting BL2
> > NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> > NOTICE: BL2: Built : 09:48:10, Feb 20 2019
> > NOTICE: BL1: Booting BL31
> > NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> > NOTICE: BL31: Built : 09:4
> >
> > U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04
> > +0100)
> >
> > Model: Marvell Armada 3720 Community Board ESPRESSOBin
> > CPU 1000 [MHz]
> > L2 800 [MHz]
> > TClock 200 [MHz]
> > DDR 800 [MHz]
> > DRAM: 2 GiB
> > Comphy chip #0:
> > Comphy-0: USB3 5 Gbps
> > Comphy-1: PEX0 2.5 Gbps
> > Comphy-2: SATA0 6 Gbps
> > Target spinup took 0 ms.
> > AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
> > flags: ncq led only pmp fbss pio slum part sxs
> > PCIE-0: Link up
> > MMC: sdhci@d0000: 0, sdhci@d8000: 1
> > Loading Environment from SPI Flash... SF: Detected w25q32dw with page
> > size 256 Bytes, erase size 4 KiB, total 4 MiB
> > OK
> > Model: Marvell Armada 3720 Community Board ESPRESSOBin
> > Net: eth0: neta@30000 [PRIME]
> > Hit any key to stop autoboot: 0
> > starting USB...
> > USB0: Register 2000104 NbrPorts 2
> > Starting the controller
> > USB XHCI 1.00
> > USB1: USB EHCI 1.00
> > scanning bus 0 for devices... 1 USB Device(s) found
> > scanning bus 1 for devices... 1 USB Device(s) found
> > scanning usb for storage devices... 0 Storage Device(s) found
> >
> > ## Loading init Ramdisk from Legacy Image at 01100000 ...
> > Image Name: uInitrd
> > Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
> > Data Size: 10750023 Bytes = 10.3 MiB
> > Load Address: 00000000
> > Entry Point: 00000000
> > Verifying Checksum ... OK
> > ## Flattened Device Tree blob at 06000000
> > Booting using the fdt blob at 0x6000000
> > Loading Ramdisk to 7ebea000, end 7f62a847 ... OK
> > Using Device Tree in place at 0000000006000000, end 00000000060059cd
> >
> > Starting kernel ...
> >
> > [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
> > [ 0.000000] Linux version 5.8.18-mvebu64 (root@beast)
> > (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture
> > 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
> > A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321)
> > #20.11.3 SMP PREEMPT Fri Dec 11 21:10:52 CET 2020
> > [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
> > [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000
> > (options '')
> > [ 0.000000] printk: bootconsole [ar3700_uart0] enabled
> > Loading, please wait...
> > Starting version 245.4-4ubuntu3.3
> > Begin: Loading essential drivers ... done.
> > Begin: Running /scripts/init-premount ... done.
> > Begin: Mounting root file system ... Begin: Running /scripts/local-top
> > ... done.
> > Begin: Running /scripts/local-premount ... Scanning for Btrfs
> > filesystems
> > done.
> > Begin: Will now check root file system ... fsck from util-linux 2.34
> > [/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0
> > /dev/mmcblk0p1
> > /dev/mmcblk0p1: clean, 41739/1828336 files, 439779/7502824 blocks
> > done.
> > done.
> > Begin: Running /scripts/local-bottom ... done.
> > Begin: Running /scripts/init-bottom ... done.
> > [ 3.694604] Internal error: synchronous external abort: 96000210
> > [#1] PREEMPT SMP
> > [ 3.699465] Modules linked in: tag_edsa mv88e6xxx dsa_core bridge
> > stp llc phy_mvebu_a3700_comphy
> > [ 3.708518] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
> > 5.8.18-mvebu64 #20.11.3
> > [ 3.716037] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
> > [ 3.722685] Workqueue: events free_work
> > [ 3.726614] pstate: 00000085 (nzcv daIf -PAN -UAO BTYPE=--)
> > [ 3.732352] pc : ahci_single_level_irq_intr+0x1c/0x90
> > [ 3.737549] lr : __handle_irq_event_percpu+0x5c/0x168
> > [ 3.742737] sp : ffffffc0113bbd10
> > [ 3.746142] x29: ffffffc0113bbd10 x28: ffffff807d48b700
> > [ 3.751608] x27: 0000000000000060 x26: ffffffc010f085e8
> > [ 3.757073] x25: ffffffc0113075a5 x24: ffffff8079101800
> > [ 3.762539] x23: 000000000000002d x22: ffffffc0113bbdd4
> > [ 3.768004] x21: 0000000000000000 x20: ffffffc011465008
> > [ 3.773470] x19: ffffff8079381600 x18: 0000000000000000
> > [ 3.778936] x17: 0000000000000000 x16: 0000000000000000
> > [ 3.784401] x15: 000000d2c010fc50 x14: 0000000000000323
> > [ 3.789867] x13: 00000000000002d4 x12: 0000000000000000
> > [ 3.795332] x11: 0000000000000040 x10: ffffffc011282dd8
> > [ 3.800798] x9 : ffffffc011282dd0 x8 : ffffff807d000270
> > [ 3.806263] x7 : 0000000000000000 x6 : 0000000000000000
> > [ 3.811729] x5 : ffffffc06ea93000 x4 : ffffffc0113bbe10
> > [ 3.817196] x3 : ffffffc06ea93000 x2 : ffffff8079101a80
> > [ 3.822661] x1 : ffffff8078803e00 x0 : 000000000000002d
> > [ 3.828126] Call trace:
> > [ 3.830642] ahci_single_level_irq_intr+0x1c/0x90
> > [ 3.835478] __handle_irq_event_percpu+0x5c/0x168
> > [ 3.840315] handle_irq_event_percpu+0x38/0x90
> > [ 3.844885] handle_irq_event+0x48/0xe0
> > [ 3.848828] handle_simple_irq+0x94/0xd0
> > [ 3.852860] generic_handle_irq+0x30/0x48
> > [ 3.856985] advk_pcie_irq_handler+0x214/0x240
> > [ 3.861552] __handle_irq_event_percpu+0x5c/0x168
> > [ 3.866389] handle_irq_event_percpu+0x38/0x90
> > [ 3.870959] handle_irq_event+0x48/0xe0
> > [ 3.874900] handle_fasteoi_irq+0xb8/0x170
> > [ 3.879112] generic_handle_irq+0x30/0x48
> > [ 3.883234] __handle_domain_irq+0x64/0xc0
> > [ 3.887447] gic_handle_irq+0xc8/0x168
> > [ 3.891298] el1_irq+0xb8/0x180
> > [ 3.894524] unmap_kernel_range_noflush+0x128/0x188
> > [ 3.899540] remove_vm_area+0xac/0xd0
> > [ 3.903303] __vunmap+0x48/0x298
> > [ 3.906618] free_work+0x44/0x60
> > [ 3.909937] process_one_work+0x1e8/0x360
> > [ 3.914057] worker_thread+0x44/0x480
> > [ 3.917820] kthread+0x154/0x158
> > [ 3.921135] ret_from_fork+0x10/0x34
> > [ 3.924812] Code: a90153f3 f9401022 f9400854 91002294 (b9400293)
> > [ 3.931087] ---[ end trace 98b323414bb99c99 ]---
> > [ 3.935829] Kernel panic - not syncing: Fatal exception in interrupt
> > [ 3.942368] SMP: stopping secondary CPUs
> > [ 3.946403] Kernel Offset: disabled
> > [ 3.949985] CPU features: 0x240002,2000200c
> > [ 3.954283] Memory Limit: none
> > [ 3.957424] ---[ end Kernel panic - not syncing: Fatal exception in
> > interrupt ]---
> >
> > The boards boots up if I don't plug in any SATA HDDs into the extension
> > card.
> >
> > I hope this helps. If you need any other information just let me know,
> > I'm absolutely willing to help. But I have no clue of kernel
> > patching/compiling etc. Sorry!
> >
> > Thank you very, very much in advance! You're doing an awesome job.
> >
> > Sincerely Rötti
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Kernel panic caused by plugging in a sata cable on a a minipcie-sata board
2021-03-08 9:54 ` Pali Rohár
@ 2021-03-15 19:32 ` Pali Rohár
2021-03-16 22:36 ` Rötti
0 siblings, 1 reply; 6+ messages in thread
From: Pali Rohár @ 2021-03-15 19:32 UTC (permalink / raw)
To: Rötti; +Cc: Marek Behún, linux-pci, linux-ide
Hello Rötti!
Can you check if that your SATA controller is working fine when is
connected to any other machine, e.g. x86 laptop or desktop?
On Monday 08 March 2021 10:54:57 Pali Rohár wrote:
> Adding linux-pci ML to the loop.
>
> Any idea where can be the issue? Problematic interrupt is triggered from
> the pci-aardvark.c driver. But I guess that issue can be in ahci code.
>
> On Sunday 07 March 2021 13:38:03 Rötti wrote:
> > Hello everyone,
> >
> > I'm sorry, I've been missing some information:
> >
> > Here is the output of lspci -nn -vv to correctly identify type of your PCIe
> > SATA controller:
> >
> > 00:00.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [1b4b:0100]
> > (prog-if 00 [Normal decode])
> > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B- DisINTx-
> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR- INTx-
> > Latency: 0, Cache Line Size: 64 bytes
> > Interrupt: pin A routed to IRQ 52
> > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> > I/O behind bridge: e9001000-e9001fff [size=4K]
> > Memory behind bridge: e8000000-e80fffff [size=1M]
> > Prefetchable memory behind bridge: [disabled]
> > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > <TAbort- <MAbort- <SERR- <PERR-
> > Expansion ROM at e8100000 [virtual] [disabled] [size=2K]
> > BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
> > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> > Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
> > DevCap: MaxPayload 512 bytes, PhantFunc 0
> > ExtTag- RBE+
> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> > MaxPayload 512 bytes, MaxReadReq 512 bytes
> > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr-
> > TransPend-
> > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
> > Latency L0s <128ns, L1 <2us
> > ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
> > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
> > TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
> > RootCap: CRSVisible-
> > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
> > CRSVisible-
> > RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> > Kernel driver in use: pcieport
> >
> > 01:00.0 SATA controller [0106]: ASMedia Technology Inc. ASM1062 Serial ATA
> > Controller [1b21:0612] (rev 02) (prog-if 01 [AHCI 1.0])
> > Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
> > [1b21:1060]
> > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B- DisINTx+
> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR- INTx-
> > Latency: 0
> > Interrupt: pin A routed to IRQ 53
> > Region 0: I/O ports at 1020 [size=8]
> > Region 1: I/O ports at 1030 [size=4]
> > Region 2: I/O ports at 1028 [size=8]
> > Region 3: I/O ports at 1034 [size=4]
> > Region 4: I/O ports at 1000 [size=32]
> > Region 5: Memory at e8010000 (32-bit, non-prefetchable) [size=512]
> > Expansion ROM at e8000000 [virtual] [disabled] [size=64K]
> > Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
> > Address: 7f044770 Data: 0035
> > Capabilities: [78] Power Management version 3
> > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> > PME(D0-,D1-,D2-,D3hot-,D3cold-)
> > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> > Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
> > DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us,
> > L1 <8us
> > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> > MaxPayload 512 bytes, MaxReadReq 512 bytes
> > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr-
> > TransPend-
> > LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM not supported
> > ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
> > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
> > TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> > DevCap2: Completion Timeout: Range ABC, TimeoutDis+,
> > NROPrPrP-, LTR-
> > 10BitTagComp-, 10BitTagReq-, OBFF Not Supported,
> > ExtFmt-, EETLPPrefix-
> > EmergencyPowerReduction Not Supported,
> > EmergencyPowerReductionInit-
> > FRS-
> > AtomicOpsCap: 32bit- 64bit- 128bitCAS-
> > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-,
> > LTR-, OBFF Disabled
> > AtomicOpsCtl: ReqEn-
> > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
> > SpeedDis-
> > Transmit Margin: Normal Operating Range,
> > EnterModifiedCompliance- ComplianceSOS-
> > Compliance De-emphasis: -6dB
> > LnkSta2: Current De-emphasis Level: -3.5dB,
> > EqualizationComplete-, EqualizationPhase1-
> > EqualizationPhase2-, EqualizationPhase3-,
> > LinkEqualizationRequest-
> > Capabilities: [100 v1] Virtual Channel
> > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> > Arb: Fixed- WRR32- WRR64- WRR128-
> > Ctrl: ArbSelect=Fixed
> > Status: InProgress-
> > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
> > WRR256-
> > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> > Status: NegoPending- InProgress-
> > Kernel driver in use: ahci
> >
> >
> > Kind regards, Rötti!
> >
> > Am 27.01.2021 22:27 schrieb Rötti:
> > > Hello everyone,
> > >
> > > I own two ESPRESSOBin boards V5.
> > >
> > > And to both I attached an XCSOURCE® MiniPCIe Sata3.0 AC696 extension
> > > card via MiniPCIe.
> > >
> > > This is the link to amazon: https://www.amazon.de/dp/B06XRG2TGV
> > >
> > > I tested several images from
> > > https://www.armbian.com/espressobin/#kernels-archive-all
> > >
> > > Tested Kernels 8 weeks ago + the latest two this week:
> > > - 5.10.09-mvebu64 #21.02.0-hirsute (trunk) <-- works not
> > > - 5.08.18-mvebu64 #20.11.6-bionic <-- works not
> > > - 5.08.18-mvebu64 #20.11.3-focal <-- works not
> > > - 5.08.18-mvebu64 #20.11.3-bionic <-- works not
> > > - 5.08.06-mvebu64 #20.08.2-focal <-- works not
> > > - 4.14.135-mvebu64 #19.11.3-bionic <-- works
> > >
> > >
> > > Here is the whole UART-dump:
> > >
> > > TIM-1.0
> > > WTMI-devel-18.12.0-a0a1cb8
> > > WTMI: system early-init
> > > SVC REV: 3, CPU VDD voltage: 1.155V
> > > NOTICE: Booting Trusted Firmware
> > > NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> > > NOTICE: BL1: Built : 09:48:09, Feb 20 2019
> > > NOTICE: BL1: Booting BL2
> > > NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> > > NOTICE: BL2: Built : 09:48:10, Feb 20 2019
> > > NOTICE: BL1: Booting BL31
> > > NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> > > NOTICE: BL31: Built : 09:4
> > >
> > > U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04
> > > +0100)
> > >
> > > Model: Marvell Armada 3720 Community Board ESPRESSOBin
> > > CPU 1000 [MHz]
> > > L2 800 [MHz]
> > > TClock 200 [MHz]
> > > DDR 800 [MHz]
> > > DRAM: 2 GiB
> > > Comphy chip #0:
> > > Comphy-0: USB3 5 Gbps
> > > Comphy-1: PEX0 2.5 Gbps
> > > Comphy-2: SATA0 6 Gbps
> > > Target spinup took 0 ms.
> > > AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
> > > flags: ncq led only pmp fbss pio slum part sxs
> > > PCIE-0: Link up
> > > MMC: sdhci@d0000: 0, sdhci@d8000: 1
> > > Loading Environment from SPI Flash... SF: Detected w25q32dw with page
> > > size 256 Bytes, erase size 4 KiB, total 4 MiB
> > > OK
> > > Model: Marvell Armada 3720 Community Board ESPRESSOBin
> > > Net: eth0: neta@30000 [PRIME]
> > > Hit any key to stop autoboot: 0
> > > starting USB...
> > > USB0: Register 2000104 NbrPorts 2
> > > Starting the controller
> > > USB XHCI 1.00
> > > USB1: USB EHCI 1.00
> > > scanning bus 0 for devices... 1 USB Device(s) found
> > > scanning bus 1 for devices... 1 USB Device(s) found
> > > scanning usb for storage devices... 0 Storage Device(s) found
> > >
> > > ## Loading init Ramdisk from Legacy Image at 01100000 ...
> > > Image Name: uInitrd
> > > Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
> > > Data Size: 10750023 Bytes = 10.3 MiB
> > > Load Address: 00000000
> > > Entry Point: 00000000
> > > Verifying Checksum ... OK
> > > ## Flattened Device Tree blob at 06000000
> > > Booting using the fdt blob at 0x6000000
> > > Loading Ramdisk to 7ebea000, end 7f62a847 ... OK
> > > Using Device Tree in place at 0000000006000000, end 00000000060059cd
> > >
> > > Starting kernel ...
> > >
> > > [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
> > > [ 0.000000] Linux version 5.8.18-mvebu64 (root@beast)
> > > (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture
> > > 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
> > > A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321)
> > > #20.11.3 SMP PREEMPT Fri Dec 11 21:10:52 CET 2020
> > > [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
> > > [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000
> > > (options '')
> > > [ 0.000000] printk: bootconsole [ar3700_uart0] enabled
> > > Loading, please wait...
> > > Starting version 245.4-4ubuntu3.3
> > > Begin: Loading essential drivers ... done.
> > > Begin: Running /scripts/init-premount ... done.
> > > Begin: Mounting root file system ... Begin: Running /scripts/local-top
> > > ... done.
> > > Begin: Running /scripts/local-premount ... Scanning for Btrfs
> > > filesystems
> > > done.
> > > Begin: Will now check root file system ... fsck from util-linux 2.34
> > > [/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0
> > > /dev/mmcblk0p1
> > > /dev/mmcblk0p1: clean, 41739/1828336 files, 439779/7502824 blocks
> > > done.
> > > done.
> > > Begin: Running /scripts/local-bottom ... done.
> > > Begin: Running /scripts/init-bottom ... done.
> > > [ 3.694604] Internal error: synchronous external abort: 96000210
> > > [#1] PREEMPT SMP
> > > [ 3.699465] Modules linked in: tag_edsa mv88e6xxx dsa_core bridge
> > > stp llc phy_mvebu_a3700_comphy
> > > [ 3.708518] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
> > > 5.8.18-mvebu64 #20.11.3
> > > [ 3.716037] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
> > > [ 3.722685] Workqueue: events free_work
> > > [ 3.726614] pstate: 00000085 (nzcv daIf -PAN -UAO BTYPE=--)
> > > [ 3.732352] pc : ahci_single_level_irq_intr+0x1c/0x90
> > > [ 3.737549] lr : __handle_irq_event_percpu+0x5c/0x168
> > > [ 3.742737] sp : ffffffc0113bbd10
> > > [ 3.746142] x29: ffffffc0113bbd10 x28: ffffff807d48b700
> > > [ 3.751608] x27: 0000000000000060 x26: ffffffc010f085e8
> > > [ 3.757073] x25: ffffffc0113075a5 x24: ffffff8079101800
> > > [ 3.762539] x23: 000000000000002d x22: ffffffc0113bbdd4
> > > [ 3.768004] x21: 0000000000000000 x20: ffffffc011465008
> > > [ 3.773470] x19: ffffff8079381600 x18: 0000000000000000
> > > [ 3.778936] x17: 0000000000000000 x16: 0000000000000000
> > > [ 3.784401] x15: 000000d2c010fc50 x14: 0000000000000323
> > > [ 3.789867] x13: 00000000000002d4 x12: 0000000000000000
> > > [ 3.795332] x11: 0000000000000040 x10: ffffffc011282dd8
> > > [ 3.800798] x9 : ffffffc011282dd0 x8 : ffffff807d000270
> > > [ 3.806263] x7 : 0000000000000000 x6 : 0000000000000000
> > > [ 3.811729] x5 : ffffffc06ea93000 x4 : ffffffc0113bbe10
> > > [ 3.817196] x3 : ffffffc06ea93000 x2 : ffffff8079101a80
> > > [ 3.822661] x1 : ffffff8078803e00 x0 : 000000000000002d
> > > [ 3.828126] Call trace:
> > > [ 3.830642] ahci_single_level_irq_intr+0x1c/0x90
> > > [ 3.835478] __handle_irq_event_percpu+0x5c/0x168
> > > [ 3.840315] handle_irq_event_percpu+0x38/0x90
> > > [ 3.844885] handle_irq_event+0x48/0xe0
> > > [ 3.848828] handle_simple_irq+0x94/0xd0
> > > [ 3.852860] generic_handle_irq+0x30/0x48
> > > [ 3.856985] advk_pcie_irq_handler+0x214/0x240
> > > [ 3.861552] __handle_irq_event_percpu+0x5c/0x168
> > > [ 3.866389] handle_irq_event_percpu+0x38/0x90
> > > [ 3.870959] handle_irq_event+0x48/0xe0
> > > [ 3.874900] handle_fasteoi_irq+0xb8/0x170
> > > [ 3.879112] generic_handle_irq+0x30/0x48
> > > [ 3.883234] __handle_domain_irq+0x64/0xc0
> > > [ 3.887447] gic_handle_irq+0xc8/0x168
> > > [ 3.891298] el1_irq+0xb8/0x180
> > > [ 3.894524] unmap_kernel_range_noflush+0x128/0x188
> > > [ 3.899540] remove_vm_area+0xac/0xd0
> > > [ 3.903303] __vunmap+0x48/0x298
> > > [ 3.906618] free_work+0x44/0x60
> > > [ 3.909937] process_one_work+0x1e8/0x360
> > > [ 3.914057] worker_thread+0x44/0x480
> > > [ 3.917820] kthread+0x154/0x158
> > > [ 3.921135] ret_from_fork+0x10/0x34
> > > [ 3.924812] Code: a90153f3 f9401022 f9400854 91002294 (b9400293)
> > > [ 3.931087] ---[ end trace 98b323414bb99c99 ]---
> > > [ 3.935829] Kernel panic - not syncing: Fatal exception in interrupt
> > > [ 3.942368] SMP: stopping secondary CPUs
> > > [ 3.946403] Kernel Offset: disabled
> > > [ 3.949985] CPU features: 0x240002,2000200c
> > > [ 3.954283] Memory Limit: none
> > > [ 3.957424] ---[ end Kernel panic - not syncing: Fatal exception in
> > > interrupt ]---
> > >
> > > The boards boots up if I don't plug in any SATA HDDs into the extension
> > > card.
> > >
> > > I hope this helps. If you need any other information just let me know,
> > > I'm absolutely willing to help. But I have no clue of kernel
> > > patching/compiling etc. Sorry!
> > >
> > > Thank you very, very much in advance! You're doing an awesome job.
> > >
> > > Sincerely Rötti
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Kernel panic caused by plugging in a sata cable on a a minipcie-sata board
2021-03-15 19:32 ` Pali Rohár
@ 2021-03-16 22:36 ` Rötti
2021-03-17 12:45 ` Pali Rohár
0 siblings, 1 reply; 6+ messages in thread
From: Rötti @ 2021-03-16 22:36 UTC (permalink / raw)
To: Pali Rohár; +Cc: Marek Behún, linux-pci, linux-ide
Hello Pali,
I'll check that. That may take a few days because I'll have to organize
a x86 device capable of using this controller.
One thing I can say is, that old Kernels have been working in this
(ARM-based) setup.
But I'll report back!
Am 15.03.2021 20:32 schrieb Pali Rohár:
> Hello Rötti!
>
> Can you check if that your SATA controller is working fine when is
> connected to any other machine, e.g. x86 laptop or desktop?
>
> On Monday 08 March 2021 10:54:57 Pali Rohár wrote:
>> Adding linux-pci ML to the loop.
>>
>> Any idea where can be the issue? Problematic interrupt is triggered
>> from
>> the pci-aardvark.c driver. But I guess that issue can be in ahci code.
>>
>> On Sunday 07 March 2021 13:38:03 Rötti wrote:
>> > Hello everyone,
>> >
>> > I'm sorry, I've been missing some information:
>> >
>> > Here is the output of lspci -nn -vv to correctly identify type of your PCIe
>> > SATA controller:
>> >
>> > 00:00.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [1b4b:0100]
>> > (prog-if 00 [Normal decode])
>> > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>> > Stepping- SERR- FastB2B- DisINTx-
>> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>> > <TAbort- <MAbort- >SERR- <PERR- INTx-
>> > Latency: 0, Cache Line Size: 64 bytes
>> > Interrupt: pin A routed to IRQ 52
>> > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>> > I/O behind bridge: e9001000-e9001fff [size=4K]
>> > Memory behind bridge: e8000000-e80fffff [size=1M]
>> > Prefetchable memory behind bridge: [disabled]
>> > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
>> > <TAbort- <MAbort- <SERR- <PERR-
>> > Expansion ROM at e8100000 [virtual] [disabled] [size=2K]
>> > BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
>> > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>> > Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
>> > DevCap: MaxPayload 512 bytes, PhantFunc 0
>> > ExtTag- RBE+
>> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
>> > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
>> > MaxPayload 512 bytes, MaxReadReq 512 bytes
>> > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr-
>> > TransPend-
>> > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
>> > Latency L0s <128ns, L1 <2us
>> > ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
>> > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
>> > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>> > LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
>> > TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
>> > RootCap: CRSVisible-
>> > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
>> > CRSVisible-
>> > RootSta: PME ReqID 0000, PMEStatus- PMEPending-
>> > Kernel driver in use: pcieport
>> >
>> > 01:00.0 SATA controller [0106]: ASMedia Technology Inc. ASM1062 Serial ATA
>> > Controller [1b21:0612] (rev 02) (prog-if 01 [AHCI 1.0])
>> > Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
>> > [1b21:1060]
>> > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>> > Stepping- SERR- FastB2B- DisINTx+
>> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>> > <TAbort- <MAbort- >SERR- <PERR- INTx-
>> > Latency: 0
>> > Interrupt: pin A routed to IRQ 53
>> > Region 0: I/O ports at 1020 [size=8]
>> > Region 1: I/O ports at 1030 [size=4]
>> > Region 2: I/O ports at 1028 [size=8]
>> > Region 3: I/O ports at 1034 [size=4]
>> > Region 4: I/O ports at 1000 [size=32]
>> > Region 5: Memory at e8010000 (32-bit, non-prefetchable) [size=512]
>> > Expansion ROM at e8000000 [virtual] [disabled] [size=64K]
>> > Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
>> > Address: 7f044770 Data: 0035
>> > Capabilities: [78] Power Management version 3
>> > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>> > PME(D0-,D1-,D2-,D3hot-,D3cold-)
>> > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>> > Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
>> > DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us,
>> > L1 <8us
>> > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
>> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
>> > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>> > MaxPayload 512 bytes, MaxReadReq 512 bytes
>> > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr-
>> > TransPend-
>> > LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM not supported
>> > ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
>> > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
>> > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>> > LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
>> > TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
>> > DevCap2: Completion Timeout: Range ABC, TimeoutDis+,
>> > NROPrPrP-, LTR-
>> > 10BitTagComp-, 10BitTagReq-, OBFF Not Supported,
>> > ExtFmt-, EETLPPrefix-
>> > EmergencyPowerReduction Not Supported,
>> > EmergencyPowerReductionInit-
>> > FRS-
>> > AtomicOpsCap: 32bit- 64bit- 128bitCAS-
>> > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-,
>> > LTR-, OBFF Disabled
>> > AtomicOpsCtl: ReqEn-
>> > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
>> > SpeedDis-
>> > Transmit Margin: Normal Operating Range,
>> > EnterModifiedCompliance- ComplianceSOS-
>> > Compliance De-emphasis: -6dB
>> > LnkSta2: Current De-emphasis Level: -3.5dB,
>> > EqualizationComplete-, EqualizationPhase1-
>> > EqualizationPhase2-, EqualizationPhase3-,
>> > LinkEqualizationRequest-
>> > Capabilities: [100 v1] Virtual Channel
>> > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
>> > Arb: Fixed- WRR32- WRR64- WRR128-
>> > Ctrl: ArbSelect=Fixed
>> > Status: InProgress-
>> > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
>> > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
>> > WRR256-
>> > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
>> > Status: NegoPending- InProgress-
>> > Kernel driver in use: ahci
>> >
>> >
>> > Kind regards, Rötti!
>> >
>> > Am 27.01.2021 22:27 schrieb Rötti:
>> > > Hello everyone,
>> > >
>> > > I own two ESPRESSOBin boards V5.
>> > >
>> > > And to both I attached an XCSOURCE® MiniPCIe Sata3.0 AC696 extension
>> > > card via MiniPCIe.
>> > >
>> > > This is the link to amazon: https://www.amazon.de/dp/B06XRG2TGV
>> > >
>> > > I tested several images from
>> > > https://www.armbian.com/espressobin/#kernels-archive-all
>> > >
>> > > Tested Kernels 8 weeks ago + the latest two this week:
>> > > - 5.10.09-mvebu64 #21.02.0-hirsute (trunk) <-- works not
>> > > - 5.08.18-mvebu64 #20.11.6-bionic <-- works not
>> > > - 5.08.18-mvebu64 #20.11.3-focal <-- works not
>> > > - 5.08.18-mvebu64 #20.11.3-bionic <-- works not
>> > > - 5.08.06-mvebu64 #20.08.2-focal <-- works not
>> > > - 4.14.135-mvebu64 #19.11.3-bionic <-- works
>> > >
>> > >
>> > > Here is the whole UART-dump:
>> > >
>> > > TIM-1.0
>> > > WTMI-devel-18.12.0-a0a1cb8
>> > > WTMI: system early-init
>> > > SVC REV: 3, CPU VDD voltage: 1.155V
>> > > NOTICE: Booting Trusted Firmware
>> > > NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
>> > > NOTICE: BL1: Built : 09:48:09, Feb 20 2019
>> > > NOTICE: BL1: Booting BL2
>> > > NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
>> > > NOTICE: BL2: Built : 09:48:10, Feb 20 2019
>> > > NOTICE: BL1: Booting BL31
>> > > NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
>> > > NOTICE: BL31: Built : 09:4
>> > >
>> > > U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04
>> > > +0100)
>> > >
>> > > Model: Marvell Armada 3720 Community Board ESPRESSOBin
>> > > CPU 1000 [MHz]
>> > > L2 800 [MHz]
>> > > TClock 200 [MHz]
>> > > DDR 800 [MHz]
>> > > DRAM: 2 GiB
>> > > Comphy chip #0:
>> > > Comphy-0: USB3 5 Gbps
>> > > Comphy-1: PEX0 2.5 Gbps
>> > > Comphy-2: SATA0 6 Gbps
>> > > Target spinup took 0 ms.
>> > > AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
>> > > flags: ncq led only pmp fbss pio slum part sxs
>> > > PCIE-0: Link up
>> > > MMC: sdhci@d0000: 0, sdhci@d8000: 1
>> > > Loading Environment from SPI Flash... SF: Detected w25q32dw with page
>> > > size 256 Bytes, erase size 4 KiB, total 4 MiB
>> > > OK
>> > > Model: Marvell Armada 3720 Community Board ESPRESSOBin
>> > > Net: eth0: neta@30000 [PRIME]
>> > > Hit any key to stop autoboot: 0
>> > > starting USB...
>> > > USB0: Register 2000104 NbrPorts 2
>> > > Starting the controller
>> > > USB XHCI 1.00
>> > > USB1: USB EHCI 1.00
>> > > scanning bus 0 for devices... 1 USB Device(s) found
>> > > scanning bus 1 for devices... 1 USB Device(s) found
>> > > scanning usb for storage devices... 0 Storage Device(s) found
>> > >
>> > > ## Loading init Ramdisk from Legacy Image at 01100000 ...
>> > > Image Name: uInitrd
>> > > Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
>> > > Data Size: 10750023 Bytes = 10.3 MiB
>> > > Load Address: 00000000
>> > > Entry Point: 00000000
>> > > Verifying Checksum ... OK
>> > > ## Flattened Device Tree blob at 06000000
>> > > Booting using the fdt blob at 0x6000000
>> > > Loading Ramdisk to 7ebea000, end 7f62a847 ... OK
>> > > Using Device Tree in place at 0000000006000000, end 00000000060059cd
>> > >
>> > > Starting kernel ...
>> > >
>> > > [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
>> > > [ 0.000000] Linux version 5.8.18-mvebu64 (root@beast)
>> > > (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture
>> > > 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
>> > > A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321)
>> > > #20.11.3 SMP PREEMPT Fri Dec 11 21:10:52 CET 2020
>> > > [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
>> > > [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000
>> > > (options '')
>> > > [ 0.000000] printk: bootconsole [ar3700_uart0] enabled
>> > > Loading, please wait...
>> > > Starting version 245.4-4ubuntu3.3
>> > > Begin: Loading essential drivers ... done.
>> > > Begin: Running /scripts/init-premount ... done.
>> > > Begin: Mounting root file system ... Begin: Running /scripts/local-top
>> > > ... done.
>> > > Begin: Running /scripts/local-premount ... Scanning for Btrfs
>> > > filesystems
>> > > done.
>> > > Begin: Will now check root file system ... fsck from util-linux 2.34
>> > > [/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0
>> > > /dev/mmcblk0p1
>> > > /dev/mmcblk0p1: clean, 41739/1828336 files, 439779/7502824 blocks
>> > > done.
>> > > done.
>> > > Begin: Running /scripts/local-bottom ... done.
>> > > Begin: Running /scripts/init-bottom ... done.
>> > > [ 3.694604] Internal error: synchronous external abort: 96000210
>> > > [#1] PREEMPT SMP
>> > > [ 3.699465] Modules linked in: tag_edsa mv88e6xxx dsa_core bridge
>> > > stp llc phy_mvebu_a3700_comphy
>> > > [ 3.708518] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
>> > > 5.8.18-mvebu64 #20.11.3
>> > > [ 3.716037] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
>> > > [ 3.722685] Workqueue: events free_work
>> > > [ 3.726614] pstate: 00000085 (nzcv daIf -PAN -UAO BTYPE=--)
>> > > [ 3.732352] pc : ahci_single_level_irq_intr+0x1c/0x90
>> > > [ 3.737549] lr : __handle_irq_event_percpu+0x5c/0x168
>> > > [ 3.742737] sp : ffffffc0113bbd10
>> > > [ 3.746142] x29: ffffffc0113bbd10 x28: ffffff807d48b700
>> > > [ 3.751608] x27: 0000000000000060 x26: ffffffc010f085e8
>> > > [ 3.757073] x25: ffffffc0113075a5 x24: ffffff8079101800
>> > > [ 3.762539] x23: 000000000000002d x22: ffffffc0113bbdd4
>> > > [ 3.768004] x21: 0000000000000000 x20: ffffffc011465008
>> > > [ 3.773470] x19: ffffff8079381600 x18: 0000000000000000
>> > > [ 3.778936] x17: 0000000000000000 x16: 0000000000000000
>> > > [ 3.784401] x15: 000000d2c010fc50 x14: 0000000000000323
>> > > [ 3.789867] x13: 00000000000002d4 x12: 0000000000000000
>> > > [ 3.795332] x11: 0000000000000040 x10: ffffffc011282dd8
>> > > [ 3.800798] x9 : ffffffc011282dd0 x8 : ffffff807d000270
>> > > [ 3.806263] x7 : 0000000000000000 x6 : 0000000000000000
>> > > [ 3.811729] x5 : ffffffc06ea93000 x4 : ffffffc0113bbe10
>> > > [ 3.817196] x3 : ffffffc06ea93000 x2 : ffffff8079101a80
>> > > [ 3.822661] x1 : ffffff8078803e00 x0 : 000000000000002d
>> > > [ 3.828126] Call trace:
>> > > [ 3.830642] ahci_single_level_irq_intr+0x1c/0x90
>> > > [ 3.835478] __handle_irq_event_percpu+0x5c/0x168
>> > > [ 3.840315] handle_irq_event_percpu+0x38/0x90
>> > > [ 3.844885] handle_irq_event+0x48/0xe0
>> > > [ 3.848828] handle_simple_irq+0x94/0xd0
>> > > [ 3.852860] generic_handle_irq+0x30/0x48
>> > > [ 3.856985] advk_pcie_irq_handler+0x214/0x240
>> > > [ 3.861552] __handle_irq_event_percpu+0x5c/0x168
>> > > [ 3.866389] handle_irq_event_percpu+0x38/0x90
>> > > [ 3.870959] handle_irq_event+0x48/0xe0
>> > > [ 3.874900] handle_fasteoi_irq+0xb8/0x170
>> > > [ 3.879112] generic_handle_irq+0x30/0x48
>> > > [ 3.883234] __handle_domain_irq+0x64/0xc0
>> > > [ 3.887447] gic_handle_irq+0xc8/0x168
>> > > [ 3.891298] el1_irq+0xb8/0x180
>> > > [ 3.894524] unmap_kernel_range_noflush+0x128/0x188
>> > > [ 3.899540] remove_vm_area+0xac/0xd0
>> > > [ 3.903303] __vunmap+0x48/0x298
>> > > [ 3.906618] free_work+0x44/0x60
>> > > [ 3.909937] process_one_work+0x1e8/0x360
>> > > [ 3.914057] worker_thread+0x44/0x480
>> > > [ 3.917820] kthread+0x154/0x158
>> > > [ 3.921135] ret_from_fork+0x10/0x34
>> > > [ 3.924812] Code: a90153f3 f9401022 f9400854 91002294 (b9400293)
>> > > [ 3.931087] ---[ end trace 98b323414bb99c99 ]---
>> > > [ 3.935829] Kernel panic - not syncing: Fatal exception in interrupt
>> > > [ 3.942368] SMP: stopping secondary CPUs
>> > > [ 3.946403] Kernel Offset: disabled
>> > > [ 3.949985] CPU features: 0x240002,2000200c
>> > > [ 3.954283] Memory Limit: none
>> > > [ 3.957424] ---[ end Kernel panic - not syncing: Fatal exception in
>> > > interrupt ]---
>> > >
>> > > The boards boots up if I don't plug in any SATA HDDs into the extension
>> > > card.
>> > >
>> > > I hope this helps. If you need any other information just let me know,
>> > > I'm absolutely willing to help. But I have no clue of kernel
>> > > patching/compiling etc. Sorry!
>> > >
>> > > Thank you very, very much in advance! You're doing an awesome job.
>> > >
>> > > Sincerely Rötti
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Kernel panic caused by plugging in a sata cable on a a minipcie-sata board
2021-03-16 22:36 ` Rötti
@ 2021-03-17 12:45 ` Pali Rohár
0 siblings, 0 replies; 6+ messages in thread
From: Pali Rohár @ 2021-03-17 12:45 UTC (permalink / raw)
To: Rötti; +Cc: Marek Behún, linux-pci, linux-ide
Hello Rötti!
Marek found a issue in that Asmedia SATA controller and sent patch
which should workaround it:
https://lore.kernel.org/linux-pci/20210317115924.31885-1-kabel@kernel.org/T/#u
Issue happen only with PCIe controllers which support 512 byte long
packets. Seems that this SATA controller presents that is capable of 512
byte long packets, but when it is enabled then controller / system
crashes.
And based on our testing, it is rare to have machine with PCIe which
support 512 byte long packets. None of our x86 Intel machine support it.
So I guess you would not be able to reproduce this issue on your x86
device and probably also not on low-end ARM device too.
You can check maximal size supported by PCIe controller by looking at
line "DevCap: MaxPayload 512 bytes" in lspci output for device named
"PCI bridge".
My Intel based laptops have only "DevCap: MaxPayload 128 bytes".
We have only two platforms (Marvell A3720 and CN9130) with 512 bytes,
which are affected and patch for both of them fixes support for that
Asmedia SATA controller.
On Espressobin (A3720 based) that issue appeared in kernel version which
introduced support for PCIe Root bridge which allows kernel to configure
MaxPayload size and therefore enable usage of 512 bytes.
On Tuesday 16 March 2021 23:36:00 Rötti wrote:
> Hello Pali,
>
> I'll check that. That may take a few days because I'll have to organize a
> x86 device capable of using this controller.
> One thing I can say is, that old Kernels have been working in this
> (ARM-based) setup.
> But I'll report back!
>
> Am 15.03.2021 20:32 schrieb Pali Rohár:
> > Hello Rötti!
> >
> > Can you check if that your SATA controller is working fine when is
> > connected to any other machine, e.g. x86 laptop or desktop?
> >
> > On Monday 08 March 2021 10:54:57 Pali Rohár wrote:
> > > Adding linux-pci ML to the loop.
> > >
> > > Any idea where can be the issue? Problematic interrupt is triggered
> > > from
> > > the pci-aardvark.c driver. But I guess that issue can be in ahci code.
> > >
> > > On Sunday 07 March 2021 13:38:03 Rötti wrote:
> > > > Hello everyone,
> > > >
> > > > I'm sorry, I've been missing some information:
> > > >
> > > > Here is the output of lspci -nn -vv to correctly identify type of your PCIe
> > > > SATA controller:
> > > >
> > > > 00:00.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [1b4b:0100]
> > > > (prog-if 00 [Normal decode])
> > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > > > Stepping- SERR- FastB2B- DisINTx-
> > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > > > <TAbort- <MAbort- >SERR- <PERR- INTx-
> > > > Latency: 0, Cache Line Size: 64 bytes
> > > > Interrupt: pin A routed to IRQ 52
> > > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> > > > I/O behind bridge: e9001000-e9001fff [size=4K]
> > > > Memory behind bridge: e8000000-e80fffff [size=1M]
> > > > Prefetchable memory behind bridge: [disabled]
> > > > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > > > <TAbort- <MAbort- <SERR- <PERR-
> > > > Expansion ROM at e8100000 [virtual] [disabled] [size=2K]
> > > > BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
> > > > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> > > > Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
> > > > DevCap: MaxPayload 512 bytes, PhantFunc 0
> > > > ExtTag- RBE+
> > > > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > > > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> > > > MaxPayload 512 bytes, MaxReadReq 512 bytes
> > > > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr-
> > > > TransPend-
> > > > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
> > > > Latency L0s <128ns, L1 <2us
> > > > ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
> > > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> > > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > > > LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
> > > > TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
> > > > RootCap: CRSVisible-
> > > > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
> > > > CRSVisible-
> > > > RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> > > > Kernel driver in use: pcieport
> > > >
> > > > 01:00.0 SATA controller [0106]: ASMedia Technology Inc. ASM1062 Serial ATA
> > > > Controller [1b21:0612] (rev 02) (prog-if 01 [AHCI 1.0])
> > > > Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
> > > > [1b21:1060]
> > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > > > Stepping- SERR- FastB2B- DisINTx+
> > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > > > <TAbort- <MAbort- >SERR- <PERR- INTx-
> > > > Latency: 0
> > > > Interrupt: pin A routed to IRQ 53
> > > > Region 0: I/O ports at 1020 [size=8]
> > > > Region 1: I/O ports at 1030 [size=4]
> > > > Region 2: I/O ports at 1028 [size=8]
> > > > Region 3: I/O ports at 1034 [size=4]
> > > > Region 4: I/O ports at 1000 [size=32]
> > > > Region 5: Memory at e8010000 (32-bit, non-prefetchable) [size=512]
> > > > Expansion ROM at e8000000 [virtual] [disabled] [size=64K]
> > > > Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
> > > > Address: 7f044770 Data: 0035
> > > > Capabilities: [78] Power Management version 3
> > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> > > > PME(D0-,D1-,D2-,D3hot-,D3cold-)
> > > > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> > > > Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
> > > > DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us,
> > > > L1 <8us
> > > > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> > > > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > > > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> > > > MaxPayload 512 bytes, MaxReadReq 512 bytes
> > > > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr-
> > > > TransPend-
> > > > LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM not supported
> > > > ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
> > > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> > > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > > > LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
> > > > TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> > > > DevCap2: Completion Timeout: Range ABC, TimeoutDis+,
> > > > NROPrPrP-, LTR-
> > > > 10BitTagComp-, 10BitTagReq-, OBFF Not Supported,
> > > > ExtFmt-, EETLPPrefix-
> > > > EmergencyPowerReduction Not Supported,
> > > > EmergencyPowerReductionInit-
> > > > FRS-
> > > > AtomicOpsCap: 32bit- 64bit- 128bitCAS-
> > > > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-,
> > > > LTR-, OBFF Disabled
> > > > AtomicOpsCtl: ReqEn-
> > > > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
> > > > SpeedDis-
> > > > Transmit Margin: Normal Operating Range,
> > > > EnterModifiedCompliance- ComplianceSOS-
> > > > Compliance De-emphasis: -6dB
> > > > LnkSta2: Current De-emphasis Level: -3.5dB,
> > > > EqualizationComplete-, EqualizationPhase1-
> > > > EqualizationPhase2-, EqualizationPhase3-,
> > > > LinkEqualizationRequest-
> > > > Capabilities: [100 v1] Virtual Channel
> > > > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> > > > Arb: Fixed- WRR32- WRR64- WRR128-
> > > > Ctrl: ArbSelect=Fixed
> > > > Status: InProgress-
> > > > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> > > > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
> > > > WRR256-
> > > > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> > > > Status: NegoPending- InProgress-
> > > > Kernel driver in use: ahci
> > > >
> > > >
> > > > Kind regards, Rötti!
> > > >
> > > > Am 27.01.2021 22:27 schrieb Rötti:
> > > > > Hello everyone,
> > > > >
> > > > > I own two ESPRESSOBin boards V5.
> > > > >
> > > > > And to both I attached an XCSOURCE® MiniPCIe Sata3.0 AC696 extension
> > > > > card via MiniPCIe.
> > > > >
> > > > > This is the link to amazon: https://www.amazon.de/dp/B06XRG2TGV
> > > > >
> > > > > I tested several images from
> > > > > https://www.armbian.com/espressobin/#kernels-archive-all
> > > > >
> > > > > Tested Kernels 8 weeks ago + the latest two this week:
> > > > > - 5.10.09-mvebu64 #21.02.0-hirsute (trunk) <-- works not
> > > > > - 5.08.18-mvebu64 #20.11.6-bionic <-- works not
> > > > > - 5.08.18-mvebu64 #20.11.3-focal <-- works not
> > > > > - 5.08.18-mvebu64 #20.11.3-bionic <-- works not
> > > > > - 5.08.06-mvebu64 #20.08.2-focal <-- works not
> > > > > - 4.14.135-mvebu64 #19.11.3-bionic <-- works
> > > > >
> > > > >
> > > > > Here is the whole UART-dump:
> > > > >
> > > > > TIM-1.0
> > > > > WTMI-devel-18.12.0-a0a1cb8
> > > > > WTMI: system early-init
> > > > > SVC REV: 3, CPU VDD voltage: 1.155V
> > > > > NOTICE: Booting Trusted Firmware
> > > > > NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> > > > > NOTICE: BL1: Built : 09:48:09, Feb 20 2019
> > > > > NOTICE: BL1: Booting BL2
> > > > > NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> > > > > NOTICE: BL2: Built : 09:48:10, Feb 20 2019
> > > > > NOTICE: BL1: Booting BL31
> > > > > NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
> > > > > NOTICE: BL31: Built : 09:4
> > > > >
> > > > > U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04
> > > > > +0100)
> > > > >
> > > > > Model: Marvell Armada 3720 Community Board ESPRESSOBin
> > > > > CPU 1000 [MHz]
> > > > > L2 800 [MHz]
> > > > > TClock 200 [MHz]
> > > > > DDR 800 [MHz]
> > > > > DRAM: 2 GiB
> > > > > Comphy chip #0:
> > > > > Comphy-0: USB3 5 Gbps
> > > > > Comphy-1: PEX0 2.5 Gbps
> > > > > Comphy-2: SATA0 6 Gbps
> > > > > Target spinup took 0 ms.
> > > > > AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
> > > > > flags: ncq led only pmp fbss pio slum part sxs
> > > > > PCIE-0: Link up
> > > > > MMC: sdhci@d0000: 0, sdhci@d8000: 1
> > > > > Loading Environment from SPI Flash... SF: Detected w25q32dw with page
> > > > > size 256 Bytes, erase size 4 KiB, total 4 MiB
> > > > > OK
> > > > > Model: Marvell Armada 3720 Community Board ESPRESSOBin
> > > > > Net: eth0: neta@30000 [PRIME]
> > > > > Hit any key to stop autoboot: 0
> > > > > starting USB...
> > > > > USB0: Register 2000104 NbrPorts 2
> > > > > Starting the controller
> > > > > USB XHCI 1.00
> > > > > USB1: USB EHCI 1.00
> > > > > scanning bus 0 for devices... 1 USB Device(s) found
> > > > > scanning bus 1 for devices... 1 USB Device(s) found
> > > > > scanning usb for storage devices... 0 Storage Device(s) found
> > > > >
> > > > > ## Loading init Ramdisk from Legacy Image at 01100000 ...
> > > > > Image Name: uInitrd
> > > > > Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
> > > > > Data Size: 10750023 Bytes = 10.3 MiB
> > > > > Load Address: 00000000
> > > > > Entry Point: 00000000
> > > > > Verifying Checksum ... OK
> > > > > ## Flattened Device Tree blob at 06000000
> > > > > Booting using the fdt blob at 0x6000000
> > > > > Loading Ramdisk to 7ebea000, end 7f62a847 ... OK
> > > > > Using Device Tree in place at 0000000006000000, end 00000000060059cd
> > > > >
> > > > > Starting kernel ...
> > > > >
> > > > > [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
> > > > > [ 0.000000] Linux version 5.8.18-mvebu64 (root@beast)
> > > > > (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture
> > > > > 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
> > > > > A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321)
> > > > > #20.11.3 SMP PREEMPT Fri Dec 11 21:10:52 CET 2020
> > > > > [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
> > > > > [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000
> > > > > (options '')
> > > > > [ 0.000000] printk: bootconsole [ar3700_uart0] enabled
> > > > > Loading, please wait...
> > > > > Starting version 245.4-4ubuntu3.3
> > > > > Begin: Loading essential drivers ... done.
> > > > > Begin: Running /scripts/init-premount ... done.
> > > > > Begin: Mounting root file system ... Begin: Running /scripts/local-top
> > > > > ... done.
> > > > > Begin: Running /scripts/local-premount ... Scanning for Btrfs
> > > > > filesystems
> > > > > done.
> > > > > Begin: Will now check root file system ... fsck from util-linux 2.34
> > > > > [/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0
> > > > > /dev/mmcblk0p1
> > > > > /dev/mmcblk0p1: clean, 41739/1828336 files, 439779/7502824 blocks
> > > > > done.
> > > > > done.
> > > > > Begin: Running /scripts/local-bottom ... done.
> > > > > Begin: Running /scripts/init-bottom ... done.
> > > > > [ 3.694604] Internal error: synchronous external abort: 96000210
> > > > > [#1] PREEMPT SMP
> > > > > [ 3.699465] Modules linked in: tag_edsa mv88e6xxx dsa_core bridge
> > > > > stp llc phy_mvebu_a3700_comphy
> > > > > [ 3.708518] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
> > > > > 5.8.18-mvebu64 #20.11.3
> > > > > [ 3.716037] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
> > > > > [ 3.722685] Workqueue: events free_work
> > > > > [ 3.726614] pstate: 00000085 (nzcv daIf -PAN -UAO BTYPE=--)
> > > > > [ 3.732352] pc : ahci_single_level_irq_intr+0x1c/0x90
> > > > > [ 3.737549] lr : __handle_irq_event_percpu+0x5c/0x168
> > > > > [ 3.742737] sp : ffffffc0113bbd10
> > > > > [ 3.746142] x29: ffffffc0113bbd10 x28: ffffff807d48b700
> > > > > [ 3.751608] x27: 0000000000000060 x26: ffffffc010f085e8
> > > > > [ 3.757073] x25: ffffffc0113075a5 x24: ffffff8079101800
> > > > > [ 3.762539] x23: 000000000000002d x22: ffffffc0113bbdd4
> > > > > [ 3.768004] x21: 0000000000000000 x20: ffffffc011465008
> > > > > [ 3.773470] x19: ffffff8079381600 x18: 0000000000000000
> > > > > [ 3.778936] x17: 0000000000000000 x16: 0000000000000000
> > > > > [ 3.784401] x15: 000000d2c010fc50 x14: 0000000000000323
> > > > > [ 3.789867] x13: 00000000000002d4 x12: 0000000000000000
> > > > > [ 3.795332] x11: 0000000000000040 x10: ffffffc011282dd8
> > > > > [ 3.800798] x9 : ffffffc011282dd0 x8 : ffffff807d000270
> > > > > [ 3.806263] x7 : 0000000000000000 x6 : 0000000000000000
> > > > > [ 3.811729] x5 : ffffffc06ea93000 x4 : ffffffc0113bbe10
> > > > > [ 3.817196] x3 : ffffffc06ea93000 x2 : ffffff8079101a80
> > > > > [ 3.822661] x1 : ffffff8078803e00 x0 : 000000000000002d
> > > > > [ 3.828126] Call trace:
> > > > > [ 3.830642] ahci_single_level_irq_intr+0x1c/0x90
> > > > > [ 3.835478] __handle_irq_event_percpu+0x5c/0x168
> > > > > [ 3.840315] handle_irq_event_percpu+0x38/0x90
> > > > > [ 3.844885] handle_irq_event+0x48/0xe0
> > > > > [ 3.848828] handle_simple_irq+0x94/0xd0
> > > > > [ 3.852860] generic_handle_irq+0x30/0x48
> > > > > [ 3.856985] advk_pcie_irq_handler+0x214/0x240
> > > > > [ 3.861552] __handle_irq_event_percpu+0x5c/0x168
> > > > > [ 3.866389] handle_irq_event_percpu+0x38/0x90
> > > > > [ 3.870959] handle_irq_event+0x48/0xe0
> > > > > [ 3.874900] handle_fasteoi_irq+0xb8/0x170
> > > > > [ 3.879112] generic_handle_irq+0x30/0x48
> > > > > [ 3.883234] __handle_domain_irq+0x64/0xc0
> > > > > [ 3.887447] gic_handle_irq+0xc8/0x168
> > > > > [ 3.891298] el1_irq+0xb8/0x180
> > > > > [ 3.894524] unmap_kernel_range_noflush+0x128/0x188
> > > > > [ 3.899540] remove_vm_area+0xac/0xd0
> > > > > [ 3.903303] __vunmap+0x48/0x298
> > > > > [ 3.906618] free_work+0x44/0x60
> > > > > [ 3.909937] process_one_work+0x1e8/0x360
> > > > > [ 3.914057] worker_thread+0x44/0x480
> > > > > [ 3.917820] kthread+0x154/0x158
> > > > > [ 3.921135] ret_from_fork+0x10/0x34
> > > > > [ 3.924812] Code: a90153f3 f9401022 f9400854 91002294 (b9400293)
> > > > > [ 3.931087] ---[ end trace 98b323414bb99c99 ]---
> > > > > [ 3.935829] Kernel panic - not syncing: Fatal exception in interrupt
> > > > > [ 3.942368] SMP: stopping secondary CPUs
> > > > > [ 3.946403] Kernel Offset: disabled
> > > > > [ 3.949985] CPU features: 0x240002,2000200c
> > > > > [ 3.954283] Memory Limit: none
> > > > > [ 3.957424] ---[ end Kernel panic - not syncing: Fatal exception in
> > > > > interrupt ]---
> > > > >
> > > > > The boards boots up if I don't plug in any SATA HDDs into the extension
> > > > > card.
> > > > >
> > > > > I hope this helps. If you need any other information just let me know,
> > > > > I'm absolutely willing to help. But I have no clue of kernel
> > > > > patching/compiling etc. Sorry!
> > > > >
> > > > > Thank you very, very much in advance! You're doing an awesome job.
> > > > >
> > > > > Sincerely Rötti
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2021-03-17 12:46 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-01-27 21:27 Kernel panic caused by plugging in a sata cable on a a minipcie-sata board Rötti
2021-03-07 12:38 ` Rötti
2021-03-08 9:54 ` Pali Rohár
2021-03-15 19:32 ` Pali Rohár
2021-03-16 22:36 ` Rötti
2021-03-17 12:45 ` Pali Rohár
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.